®
Chromalox
SERVICE REFERENCE
Installation, Operation,
DIVISION
SALES
4
SECTION TL
Maintenance Instructions
(Supersedes PD411-9)
REFERENCE
PD411-10
and
161-048529-001
DATE
AUGUST, 2008
RENEWAL PARTS IDENTIFICATION
Incorporates PD410-8 and PD413-6.
These manuals have been discontinued.
Type TLC, TLO, TLS, TLI, KTLC, KTLO, KTLS,
KTLI, KBLC, KBLS, BLCK, & BLCS Series
Industrial Over-The-Side Immersion Heaters
Type KBLS
Type TLC
Type KTLC
Shown above are Moisture Resistant Terminal Enclosures. Explosion Resistant Terminal Enclosure not shown.
Note: Consult factory for specific installation instructions for heaters with additional features not detailed in this installation guide.
Such additional features may include thermocouples supplied as a special order modification.
GENERAL
Safety Guidelines
Read and follow these instructions to minimize risks of electric
shock or fire. Save these instructions for future reference.
The safety and performance of this heater is dependent on proper
handling, installation, control and maintenance. As Chromalox can not
anticipate all conditions under which this information and heater, or
this heater in combination with other manufacturer’s products may be
used, it is advised that you conduct your own tests to determine the
safety and suitability of this heater in combination with other products
in your application. Where the consequences of overheating or failure
could result in personal injury or property damage, back-up controls
and safety devices are essential.
Chromalox Type TLC, TLO,TLS,TLI, KTLC, KTLO, KTLS,
KTLI, KBLC, KBLS, BLCK, & BLCS series industrial Over-The-
Side immersion heaters are designed for a wide variety of heating
applications.
1. Heater Construction Characteristics
A. High quality resistance wire held in place by compacted
Magnesium Oxide Refractory or compacted proprietary
cement enclosed in a wide variety of sheath materials.
B. Low to high watt densities.
The Safety Alert Symbol:
is found throughout these installa-
tion instructions to identify potential hazards that can result in person-
al injury. The seriousness of the potential risk is identified by one of
these three words:
C. Standard selection of sheath materials include copper, steel,
INCOLOY® alloy and stainless steel. This broad selection of
sheath materials will operate successfully in many corrosive
solutions.
– will result in serious injury or death.
!
– could result in serious injury or death.
WARNING
!
– may result in minor or moderate injury.
© 2010 Chromalox, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS (cont’d.)
KTLC, KTLI, KTLO, KTLS
Section A-A
(B)
(A)
Min. Tank
Clearance
(A)
A
A
(B)
(B)
Figure 2
Figure 1
Specifications –
Dimensions (In.)
(A) Standard (B) Min.
Element
Tank Opening Arrange-
No.
No.
Sheath
Riser
Model
Elements Phase
Volts
kW
Model
Elements
Phase
Volts
kW
Material
Height
Clearance
ment
KTLC-210
KTLC-212
2
2
1
1
240-480
240-480
10
12
KTLC-315
KTLC-318
3
3
1 or 3Δz
1 or 3Δz
240-480
240-480
15
18
Copper
Copper
48
48
21-1/4
23-1/2
Fig. 2
Fig. 2
1 or 3Δz
1 or 3Y
120-240
480
KTLC-220
2
1
120-240-480
2
KTLC-330
3
3
Copper
36
10-5/8
Fig. 1
KTLC-240
KTLC-260
KTLC-280
2
2
2
1
1
1
120-240-480
120-240-480
240-480
4
6
8
KTLC-360
KTLC-390
KTLC-312
3
3
3
1 or 3Δ
1 or 3Δ
1 or 3Δ
120-240-480
120-240-480
240-480
6
9
12
Copper
Copper
Cooper
36
36
36, 48
13-3/4
16-1/8
18-5/8
Fig. 2
Fig. 2
Fig. 2
KTLI-210
KTLI-212
2
2
1
1
240-480
240-480
10
12
KTLI-315
KTLI-318
3
3
1 or 3Δ
1 or 3Δ
240-480
240-480
15
18
Incoloy
Incoloy
48
48
21-1/4
23-1/2
Fig. 2
Fig. 2
1 or 3Δ
1 or 3Y
120-240
480
KTLI-220
2
1
120-240-480
2
KTLI-330
3
3
Incoloy
36
10-5/8
Fig. 1
KTLI-240
KTLI-260
KTLI-280
2
2
2
1
1
1
120-240-480
120-240-480
240-480
4
6
8
KTLI-360
KTLI-390
KTLI-312
3
3
3
1 or 3Δ
1 or 3Δ
1 or 3Δ
120-240-480
120-240-480
240-480
6
9
12
Incoloy
Incoloy
Incoloy
36
36
36, 48
13-3/4
16-1/8
18-5/8
Fig. 2
Fig. 2
Fig. 2
KTLO-220
KTLO-230
KTLO-240
KTLO-250
KTLO-260
KTLO-270
2
2
2
2
2
2
1
1
1
1
1
1
120-240-480
120-240-480
120-240-480
120-240-480
120-240-480
240-480
2
3
4
5
6
7
KTLO-330
KTLO-345
KTLO-360
KTLO-375
KTLO-390
KTLO-310
3
3
3
3
3
3
1 or 3Δ
1 or 3Δ
1 or 3Δ
1 or 3Δ
1 or 3Δ
1 or 3Δ
120-240-480
120-240-480
120-240-480
120-240-480
120-240-480
240-480
3
4.5
6
7.5
9
10
Steel
Steel
Steel
Steel
Steel
Steel
36
36
36, 48
48
48
48
13-3/4
16-1/8
18-5/8
21-1/4
23-1/2
24-7/8
Fig. 2
Fig. 2
Fig. 2
Fig. 2
Fig. 2
Fig. 2
KTLS-210
KTLS-212
2
2
1
1
240-480
240-480
10
12
KTLS-315
KTLS-318
3
3
1 or 3Δ
1 or 3Δ
240-480
240-480
15
18
Stainless Steel
Stainless Steel
48
48
21-1/4
23-1/2
Fig. 2
Fig. 2
1 or 3Δ
1 or 3Y
120-240
480
KTLS-220
2
1
120-240-480
2
KTLS-330
3
3
Stainless Steel
36
10-5/8
Fig. 1
KTLS-240
KTLS-260
KTLS-280
2
2
2
1
1
1
120-240-480
120-240-480
240-480
4
6
8
KTLS-360
KTLS-390
KTLS-312
3
3
3
1 or 3Δ
1 or 3Δ
1 or 3Δ
120-240-480
120-240-480
240-480
6
9
12
Stainless Steel
Stainless Steel
Stainless Steel
36
36
36, 48
13-3/4
16-1/8
18-5/8
Fig. 2
Fig. 2
Fig. 2
KBLC, KBLS
Specifications –
DIMENSIONS
Inches
(A)
(B)
Kw
(11 WPSI)
Riser
Height
Min. Opening
Clearance
Model
Volts
Type KBLC – Steel Construction
KBLC-24
120 or 240
120 or 240
120 or 240
240 only
240 only
240 only
2.2
2.2
2.2
4.4
4.4
4.4
36
36
36
36
36
36
12-3/4
12-3/4
12-3/4
17-3/4
17-3/4
17-3/4
KBLC-24T2
KBLC-24T3
KBLC-28
(A)
KBLC-28T2
KBLC-28T3
Type KBLS – Stainless Steel Construction
KBLS-244
120 or 240
120 or 240
120 or 240
120 or 240
240 only
2.2
2.2
2.2
2.2
4.4
4.4
4.4
4.4
36
36
36
36
36
36
36
36
12-3/4
12-3/4
12-3/4
12-3/4
17-3/4
17-3/4
17-3/4
17-3/4
KBLS-244T1
KBLS-244T2
KBLS-244T3
KBLS-288
KBLS-288T1
KBLS-288T2
KBLS-288T3
240 only
240 only
240 only
(B)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS (cont’d.)
1-1/4” Pipe Opening
C
BLCK, BLCS
L
of Mtg. Hole
same as Dim. “A”
1-1/4” Ground Joint
Malleable Iron Union
Type BLCK-MH
Suspension Bracket
(4-5/32)
1-1/4” Round
Floor Flange
(A)
Malleable Iron
(C)
(A)
Type BLCS
4 to 12 Blades
(C)
1-1/4” Steel
Pipe Riser
4 to 12 Blades
(B)
(B)
Specifications –
Model
Kilowats
Fuel Oil
12 W/in2
Dimensions (In.)
(B) Min. Tank
Riser Height Opening Clearance
No.
Blades
Regular Oil
18 W/in2
(A)
Phase
40 W/in2
Voltage
(C)
BLCK-MH618
BLCK-MH824
BLCK-MH103
BLCK-MH236
6
8
10
12
1 or 3 ⌬
1 or 3 ⌬
1 or 3 ⌬
1 or 3 ⌬
12
16
20
24
7.5
10
12.5
15
–
–
–
–
240 or 480
240 or 480
240 or 480
240 or 480
144
144
144
144
16-1/2
16-1/2
16-1/2
16-1/2
8-7/8
12
15-1/8
18-1/4
BLCS-618
BLCS-824
BLCS-1030
BLCS-1236
6
8
10
12
1 or 3 ⌬
1 or 3 ⌬
1 or 3 ⌬
1 or 3 ⌬
12
16
20
24
7.5
10
12.5
15
–
–
–
–
240 or 480
240 or 480
240 or 480
240 or 480
144
144
144
144
34
34
34
34
8-7/8
12
15-1/8
18-1/4
electric heating equipment. Where the conse-
quences of failure could result in personal injury or
property damage, back-up controls are essential.
FIRE HAZARD. An integral thermostat, if provided,
is designed for temperature control service only.
Because the thermostat does not fail safe, it should
not be used for temperature limiting duty. Wiring to
this device is the responsibility of the user.
FIRE/EXPLOSION HAZARD. Use only Explosion
Resistant Enclosures (E2, E3 or ER) in hazardous
atmospheres where flammable vapors, gases, liquids
or other combustible atmospheres are present as
defined in the National Electrical Code (NFPA 70).
Failure to comply could result in personal injury or
property damage.
The system designer is responsible for the safety
of this equipment and should install adequate
back-up controls and safety devices with their
INSTALLATION
7. When melting solids by direct immersion, a surface vent should be
provided to allow gases to escape. Operate the heater on half volt-
age until melted material completely covers the heater area.
8. A drip loop is recommended to minimize passage of moisture
along wiring into terminal enclosure and connections.
ELECTRIC SHOCK HAZARD. Disconnect all power
before installing or servicing heater. Failure to do
so could result in personal injury or property dam-
age. Heater must be installed by a qualified person
in accordance with the National Electrical Code,
NFPA 70.
FIRE HAZARD. Since heaters are capable of developing
high temperatures, extreme care should be taken to:
A. Use explosion-resistant terminal enclosures in hazardous loca-
tions. Consult Chromalox for selection of explosion-resistant
terminal enclosures for hazardous locations.
1. Before installing, check your Over-The-Side heater for any dam-
age that may have occurred during shipment. Also, check to ensure
that the line voltage is the same as that stamped on the nameplate.
2. Do not bend heating elements. If bending is necessary, consult factory.
3. IMPORTANT: Mount the heater in the tank so that the liquid
level will always be above the effective heated portion of the
heater. If the heater is not properly submerged, it will overheat and
damage the heating elements and create a possible fire hazard due
to excessive sheath temperatures. See “Warning” under
“Installation” section. (see Figure 3).
B. Avoid contact between heater and combustible materials.
C. Keep combustible materials far enough away to be free of the
effects of high temperatures.
!
FREEZE HAZARD. Some Over-The-Side heaters are
equipped with a thermowell for process control or
over-temperature control. Do not allow moisture to
accumulate in thermowell. Freezing temperatures
can cause damage that may result in the heated
medium leaking into terminal enclosure.
4. Heater must be supported from tank bottom. Heater must not be
operated in sludge. Sludge legs can be provided. Assemble as
shown in Figure 3.
5. Where work will pass over or near equipment, additional protec-
tion, such as a metal guard, may be needed.
6. In the electroplating operation the heaters are not, under any cir-
cumstance, to be placed between the electrodes and the work.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION (cont’d.)
9. To prevent moisture accumulation in cryogenic applications or
when heater is exposed to freezing temperatures:
A. Slope conduit away from enclosure (drip loop).
B. Seal all conduit openings to moisture/explosion resistant ter-
minal enclosure.
FIRE OR EXPLOSION HAZARD. If the heater is not
properly submerged, the heating elements will over-
heat and could result in a fire or damaged equipment.
C. Insulate terminal enclosure.
NOTE: If heating in closed vessels, controls and
backup controls must be used to prevent buildup of
temperature and/or pressure. Maximum pressure
rating is 50 PSI.
FIRE OR SHOCK HAZARD. Moisture accumulation
in the element refractory material, element over-
temperature, or sheath corrosion can cause
ground fault to the element sheath, generating arc-
ing and molten metal. Install Ground Fault Circuit-
Interrupter (GFCI) to prevent personal injury or
Equipment Ground Fault Protection to prevent
property damage.
Suitable Wiring
Drip Loop recommended to
minimize passage of moisture
along wiring into terminal
wiring connections.
Expected Low Liquid Level
10. Heaters with floor flange:
A. Remove electrical enclosure.
B. Mount heater to tank or manhole cover.
C. Install electrical enclosure.
6 to 8"
Always maintain a minimum of
Minimum
6 to 8" of liquid above the heated
portion of the element to prevent
exposure of the effective
heated length.
!
Expected maximum
Fittings into electrical enclosure must be properly
sealed to prevent contamination of electrical con-
tacts from vapors.
Sludge Legs
sediment level
NOTE: Locate the heater as low as possible for maximum
heated liquid storage capacity. Heat does not move downward.
FIGURE 3 Open Tank Illustration
WIRING
6. Heaters are prewired and tagged for easy installation of electrical
wiring to the heater. Tagging of the individual circuits of
Chromalox Industrial Over-The-Side Immersion heaters is shown
in the following tabulations. Refers to Type TLC, TLO, TLS, TLI,
KTLC, KTLO, KTLS, KTLI, KBLC, KBLS, BLCK, and BLCS
Series heaters.
7. Make sure heater, is grounded by attaching ground conductor,
traceable back to service entrance, to the ground terminal located
inside the terminal enclosure. If heater is used in an electroplating
tank, the heater should be grounded externally to the tank wall to
minimize stray plating currents in heater sheath that may cause
sheath corrosion.
ELECTRIC SHOCK HAZARD. Any installation involv-
ing electric heaters must be performed by a quali-
fied person and must be effectively grounded in
accordance with the National Electrical Code to
eliminate shock hazard.
1. Electric wiring to heater must be installed in accordance with the
National Electrical Code and with local codes by a qualified per-
son. CAUTION: Use copper conductors only.
2. When element wattages are not equal, heaters must not be con-
nected in series.
8. Check for loose terminal connections and tighten if necessary.
Made to order items are prewired and tagged at the factory. Wiring
of made to order items may differ from those shown in the tabu-
lations. Carefully check voltage and phase on the heater name-
plate and select either the appropriate wiring shown above or
check for the appropriate wiring diagram in the heater termi-
nal enclosure. For reference purposes, some typical wiring dia-
grams are shown in the following figures.
3. Electrical wiring to heater should be contained in rigid conduit or
in sealed flexible conduit to keep corrosive vapors and liquids out
of the terminal enclosure. If high humidity is encountered, the con-
duit should slope away from the heater.
4. If flexible cord is employed, a watertight connector should be used
for entry of the cord into the terminal enclosure. Outdoor applica-
tions require liquid-tight conduit and connectors.
5. Bring the power line wires through the opening in the terminal
enclosure.
WIRING DIAGRAMS – TLC, TLO, TLS, TLI
120V 120V 240V 240V 480V 480V 480V
120V 120V 240V 240V 480V 480V 480V
Model
1ø
3øΔz
1ø
3øΔz
1ø
3øΔz 3øY
Model
1ø
3øΔz
1ø
3øΔz
1ø
3øΔz 3øY
Fig.
Fig. Fig.
Fig. Fig.
Fig. Fig.
Fig.
Fig.
Fig.
Fig.
Fig.
Fig. Fig.
TLC, TLI and TLS 210
TLC, TLI and TLS 212
TLC, TLI, TLO and TLS 220
TLO 230
TLC, TLI, TLO and TLS 240
TLO 250
TLC, TLI, TLO and TLS 260
TLO 270
TLC, TLI and TLS 280
—
—
1
—
—
—
—
—
—
—
—
—
1
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
1
1
2
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
TLO 310
—
—
—
—
3
—
—
—
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
3
3
3
3
5
3
3
3
3
4
4
4
4
4
4
4
4
4
—
—
—
—
6
—
—
—
—
TLC, TLI and TLS 312
TLC, TLI and TLS 315
TLC, TLI and TLS 318
TLC, TLI, TLO and TLS 330
TLO 345
1
1
4
4
4
4
4
1
3
1
TLC, TLI, TLO and TLS 360
TLO 375
TLC, TLI, TLO and TLS 390
3
—
—
3
3
Note: Use wire size and type specified by NEC.
480V heaters require 600V wire per NEC.
480V heaters require a contactor.
Contactor and wiring supplied by customer.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAMS – KTLC, KTLO, KTLS, KTLI
120V 120V 240V 240V 480V 480V 480V
120V 120V 240V 240V 480V 480V 480V
Model
1ø
3øΔz
1ø
3øΔz
1ø
3øΔz 3øY
Model
1ø
3øΔz
1ø
3øΔz
1ø
3øΔz 3øY
Fig.
Fig. Fig.
Fig. Fig.
Fig. Fig.
Fig.
Fig.
Fig.
Fig.
Fig.
Fig. Fig.
KTLC, KTLI and KTLS 210
KTLC, KTLI and KTLS 212
KTLC, KTLI, KTLO and KTLS 220
KTLO 230
KTLC, KTLI, KTLO and KTLS 240
KTLO 250
KTLC, KTLI, KTLO and KTLS 260
KTLO 270
KTLC, KTLI and KTLS 280
—
—
1
—
—
—
—
—
—
—
—
—
1
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
1
1
2
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
KTLO 310
—
—
—
—
3
—
—
—
3
3
3
3
3
3
3
3
3
4
4
4
4
4
4
4
4
4
3
3
3
3
5
3
3
3
3
4
4
4
4
4
4
4
4
4
—
—
—
—
6
—
—
—
—
KTLC, KTLI and KTLS 312
KTLC, KTLI and KTLS 315
KTLC, KTLI and KTLS 318
KTLC, KTLI, KTLO and KTLS 330
KTLO 345
1
1
4
4
4
4
4
1
3
1
KTLC, KTLI, KTLO and KTLS 360
KTLO 375
KTLC, KTLI, KTLO and KTLS 390
3
—
—
3
3
Note: Use wire size and type specified by NEC.
480V heaters require 600V wire per NEC.
480V heaters require a contactor.
Contactor and wiring supplied by customer.
WIRING DIAGRAMS – BLCK, BLCS
120V 120V 240V 240V 480V 480V 480V
120V 120V 240V 240V 480V 480V 480V
Model
1ø
3øΔz
1ø
3øΔz
1ø
3øΔz 3øY
Model
1ø
3øΔz
1ø
3øΔz
1ø
3øΔz 3øY
Fig.
Fig. Fig.
Fig. Fig.
Fig. Fig.
Fig.
Fig.
Fig.
Fig.
Fig.
Fig. Fig.
BLCK
—
—
1
4
1
4
—
BLCS
—
—
7
8
7
8
—
Note: Use wire size and type specified by NEC.
480V heaters require 600V wire per NEC.
480V heaters require a contactor.
Contactor and wiring supplied by customer.
Factory
Field
Factory
Field
Term. Block
Contactor
Term. Block
Contactor
L1
L2
L1
L2
120V
or
120V
or
240V
240V
Junction Box
Junction Box
Low
Low
Liquid
Control
Thermostat
Liquid
Control
Thermostat
WIRING DIAGRAM 2
WIRING DIAGRAM 1
Factory
Field
Factory
Field
Term. Block
Term. Block
Contactor
Contactor
L1
L2
L3
L1
L2
120V
or
240V
120V
or
240V
Junction Box
Junction Box
Low
Low
Liquid
Thermostat
Liquid
Control
Thermostat
Control
WIRING DIAGRAM 3
WIRING DIAGRAM 4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Factory
Field
Factory
Field
Term. Block
Contactor
Term. Block
Contactor
L1
L2
L1
L2
L3
120V
or
240V
120V
or
Junction Box
240V
Low
Junction Box
Liquid
Control
Thermostat
Low
Liquid
Control
Thermostat
WIRING DIAGRAM 5
WIRING DIAGRAM 6
Factory
Field
Factory
Field
Term. Block
Contactor
Term. Block
Contactor
L1
L1
L2
L3
L2
120V
or
240V
120V
or
Junction Box
Junction Box
240V
Low
Liquid
Control
Thermostat
Low
Thermostat
Liquid
Control
WIRING DIAGRAM 7
WIRING DIAGRAM 8
OPERATION
1. Do not operate heater at voltages in excess of that stamped on the
assemblies or 20 megohm on individual unsealed elements. It is
recommended that heaters with 1 megohm or less be dried out
before applying full power. If dried properly, low megohm will not
effect heater life or efficiency.
To correct a low megohm condition, remove terminal enclosure
cover, gaskets, and terminal hardware. Bake heaters in an oven at
300 to 500˚F for several hours or preferably overnight.
An alternate procedure is to cycle the heater in 10 to 15 minute
periods at low voltage until megohm values are normal. Sheath
temperatures should not exceed 350˚F.
heater since excess voltage will shorten heater life.
2. Always maintain a minimum of 6 to 8” of liquid above the heated
portion of the element to prevent exposure of the effective heated
length. If the heater is not properly submerged, it will overheat and
shorten heater life. DO NOT OPERATE HEATER IF DRY.
3. Keep heating elements above sediment deposits.
4. Low Megohm Condition — The refractory material used in elec-
tric heaters may absorb moisture during transit, storage or when
subject to humid environments that will reduce the cold insulation
resistance (low megohm). Low megohm may result in a high leak-
age current to ground and nuisance trips of ground fault protection
equipment. Normally, the megohm value increases after heat-up.
Typical insulation valves are 5 megohm or greater on complete
NOTE: Low megohm on heating elements with epoxy or hermetic
seals cannot be serviced in the field. Typical resistance val-
ues when sealed are 200 megohm or greater. Contact Chro-
malox service center at number listed.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Note: User is responsible for maintenance schedule based on their
knowledge of the heated medium and operating conditions.
3. Remove any accumulated sludge deposits from heater and from
tank.
ELECTRIC SHOCK HAZARD. Disconnect all power
before installing or servicing heater. Failure to do so
could result in personal injury or property damage.
4. Check for loose terminal connections.
5. If corrosion is indicated in the terminal enclosure, check termi-
nal enclosure gasket and replace if necessary. Check conduit
layout to correct conditions that allow corrosion to enter the ter-
minal enclosure.
1. Heaters should be checked periodically for coatings and corrosion
and cleaned if necessary.
2. The tank should be checked regularly for sediment around the
heater as sediment can act as an insulator and shorten heater life.
Note: Applies to all items, not just #2.
6. Clean terminal ends of all contamination.
RENEWAL PARTS
1. Thermostat Kit (order by PCN):
Gasket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .132-012603-004
Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .080-012602-001
4 Post Terminal Block . . . . . . . . . . . . . . . . . . . . . . .303-001843-001
3 Post Terminal Block . . . . . . . . . . . . . . . . . . . . . . .303-006621-003
Thermostat Mounting Bracket . . . . . . . . . . . . . . . . .027-072456-001
A.0-100°F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PCN 277835
B.60-250°F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .PCN 277819
2. Thermostat Knob:
A.0-100°F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169-019605-002
B.60-250°F . . . . . . . . . . . . . . . . . . . . . . . . . . . . .169-019604-001
C. 200-550˚F . . . . . . . . . . . . . . . . . . . . . . . . . . . .169-019604-002
3. Sludge Legs:
4. Thermostat
A.0-100°F (84” Capillary) . . . . . . . . . . . . . . . . . .300-048518-005
B.60-250°F (84” Capillary) . . . . . . . . . . . . . . . . .300-048518-002
C. 200-550˚F (84” Capillary) . . . . . . . . . . . . . . . .300-048518-004
D.0-100°F (144” Capillary) . . . . . . . . . . . . . . . . .300-048518-019
E. 60-250°F (180” Capillary) . . . . . . . . . . . . . . . .300-048518-022
F. 200-550˚F (180” Capillary) . . . . . . . . . . . . . . .300-048518-023
A.TLC, KTLC Series . . . . . . . . . . . . . . . . . . . . . .176-114713-001
B.TLI, KTLI Series . . . . . . . . . . . . . . . . . . . . . . .176-114713-001
C.TLO, KTLO Series . . . . . . . . . . . . . . . . . . . . . .176-114713-002
D.TLS, KTLS Series . . . . . . . . . . . . . . . . . . . . . .176-114713-003
Limited Warranty:
Please refer to the Chromalox limited warranty applicable to this product at
2150 N. RULON WHITE BLVD., OGDEN, UT 84404
TA -V7 - EF
Litho in U.S.A.
Phone: 1-800-368-2493
Download from Www.Somanuals.com. All Manuals Search And Download.
|