I N S T A L L A T I O N I N S T R U C T I O N S
Small Flat Panel In-Wall Swing Arm Mount
FWDIW Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FWDIW Series
TOOLS REQUIRED FOR INSTALLATION AND PARTS
3/16"
(Included)
B (4)
2 short (SIDES)
2 long
A (1)
I/M
x1
E (4)
1/4"
C (4)
D (4)
5/16"
5/16-18 x 5/8"
F (1)
K (2)
08 x 1/2"
J (4)
8-32 x 3/8"
G (2)
H (2)
P (4)
N (1)
3/16"
L (12)
M (4)
Q
R
Q4 (1)
Q1 (4)
M4x8mm
R5 (4)
R1 (4)
R2 (4)
M4x12mm
M4x30mm
M4x20mm
Q2 (6)
M4x16mm
R3 (4)
.375"
R4 (4)
.750"
Q3 (6)
1/8"
3
Download from Www.Somanuals.com. All Manuals Search And Download.
FWDIW Series
Installation Instructions
with four mounting holes in FAC501. (See Figure 2)
Installation
The following procedure assumes that a Chief Model FAC501
In-Wall accessory has previously been installed following the
installation instructions provided by the manufaurer. If a
FAC501 is not installed or there are any other questions
regarding the installation of this accessory, immediately contact
Chief.
Swing Arm
Mounting
Bracket
5
WARNING: IMPROPER INSTALLATION CAN LEAD TO
MOUNT FALLING CAUSING SEVERE PERSONAL INJURY
OR DAMAGE TO EQUIPMENT! DO NOT deviate from
installation instructions provided. DO NOT substitute
hardware.
3
Install Bumper
1. Install two bumpers (G) to bumper mounting bracket (F).
(See Figure 1)
4
NOTE: A screwdriver may be required to push bumper into
hole in bumper mounting bracket.
2. Secure bumper mounting bracket (F) to FAC501 onto the
side the arm will be located when retracted using two
Phillips pan head screws (K). (See Figure 1)
Lower Support Plate
Figure 2
1
6. Secure swing arm to FAC501 using four button head cap
screws (C), four lock washers (D) and four flat washers (E).
(F) x1
NOTE: The mounting holes in the swing arm monting bracketd
are slotted horizontally to allow the mount to be slighlty
off-center to provide better cable clearance.
(G) x2
2
(K) x2
6
(E) x4
(C) x4
(D) x4
Figure 1
3. Align bottom of swing arm pivot pin with hole in lower
support plate. (See Figure 2)
Figure 3
4. Lower swing arm until pivot pin rests in hole in lower support
plate. (See Figure 2)
5. Align four mounting holes in swing arm mounting bracket
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FWDIW Series
Display Installation
The mounting holes on the back of the display will either be
flush with the back surface, or recessed into the back surface.
Refer to the applicable installation procedure below.
2
Flush Mount Display
3
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Using screws of
improper size may damage your display! Proper screws will
easily and completely thread into display mounting holes.
Ensure that screws are not too long.
4
WARNING: IMPROPER INSTALLATION CAN LEAD TO
DISPLAY FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Inadequate thread
engagement in display may cause display to fall! Back out
screws ONLY as necessary to allow installation of Centris
bracket!
(R1) x 2
1. Partially install two screws (R1) into upper mounting holes
in display back. (See Figure 4)
Figure 5
NOTE: Leave at least 1/8" of each screw protruding out back
of display.
Recessed Mount
1. Place four spacers (R3, R4) over each mounting hole in
display back.
2. Align teardrop mounting holes in faceplate with holes in
spacers (R3, R4).
3. Install four Phillips pan head screws (R2) through faceplate
and spacers (R3, R4) and into mounting holes in back of
display.
1
4. Tighten all screws.
2
1
(R1) x2
Figure 4
3
2. Align two screws (R1) in display back with upper teardrop
mounting holes in faceplate. (See Figure 5)
3. Place two screws (R1) in display back into upper teardrop
mounting holes in faceplate and lower display until screws
are seated in lower area of teardrop mounting holes.
(See Figure 5)
(R2) x 4
(R3, R4) x 4
4. Install two screws (R1) through lower mounting holes in
faceplate and into display back. (See Figure 5)
5. Tighten all hardware.
Figure 6
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FWDIW Series
Installation Instructions
lower mounting holes in interface bracket (Q4).
(See Figure 9)
Attach Interface Bracket to Display
1. Lay display face down on a clean and dry flat surface.
2. Attach Interface Bracket (Q4) to display using six M4x16mm
Phillips flat machine screws (Q2) and six 1/8" spacers (Q3).
(See Figure 7)
3. Tighten all screws.
(Q4)
(Q4)
(R1) x 4
(Q2) x 6
(Q3) x 6
Figure 9
Figure 7
Cable Management
Attach Display to Mount
1. Attach all cables to display.
1. Start two M4 x 12mm Phillips pan head screws (R1) into top
mounting holes on interface bracket (Q4). (See Figure 8)
CAUTION: Ensure that adequate cable slack exists for
movement of display, and that cables will not be pinched by
installation of cover (H) or screws (J).
2. Align two screws in interface bracket (Q4) with upper
mounting holes in Centris cup and lower display until
screws are seated in lower area of teardrop mounting
holes. (See Figure 8)
2. Carefully insert cables in cavity located in lower portion of
mount arm (See Figure 10).
3. Using Phillips screwdriver, install cover (H) with two screws
(J). (See Figure 10)
2
3
Cable Path
(typical)
(H) x 2
(J) x 4
(R1) x 4
(Q4)
Figure 8
3. Hold display so that display back is against Centris cup and
install two M4 x 12mm Phillips pan head machine screws
(R1) through lower mounting holes in Centris cup and into
Figure 10
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
FWDIW Series
Trim Installation
To install optional trim;
1. Remove paper covering adhesive and affix three tape
squares (L) to inside lower flange of each trim piece (B).
(See Figure 11)
2. Orient trim pieces (B) as shown in figure below.
(See Figure 11)
3. Remove paper covering adhesive back from tape squares
(L) on trim and press trim (B) against inner wall of box.
(See Figure 11)
2
3
Figure 12
(B) x 4
(L) x 12
To adjust display Roll, Pitch, and YAW tension:
1. Disconnect all wires and cable from the display.
2. Remove two Lower screws securing display to Centris cup.
3. Loosen two Upper screws securing display.
4. Lift display upward and away from mount.
Figure 11
Adjustments
Swing Arm
PIVOT / SWING Tension
5. Using a Phillips screwdriver turn the tension adjustment
screw clockwise to increase tension, or counter-clockwise
to decrease tension. (See Figure 13)
1. Using 3/16" hex key (N), slightly loosen or tighten the
adjustment screw(s) as necessary (See Figure 12).
6. Re-install display.
Figure 13
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FWDIW Series
Installation Instructions
USA/International
Europe
A
P
F
A
P
F
8401 Eagle Creek Parkway, Savage, MN 55378
800.582.6480 / 952.894.6280
877.894.6918 / 952.894.6918
Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
+31 (0)40 2668620
Chief Manufacturing, a division of
Milestone AV Technologies
+31 (0)40 2668615
Asia Pacific
A
Room 24F, Block D, Lily YinDu International Building
LuoGang, BuJi Town, Shenzhen, CHINA.
8805-000240 Rev B
¤2008 Milestone AV Technologies
10/08
P
F
+86-755-8996 9226
+86-755-8996 9217
Download from Www.Somanuals.com. All Manuals Search And Download.
|