1-1/2 HP Plunge RouteR
67119
Set uP and oPeRating inStRuctionS
®
distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe tHiS manual.
©
®
Copyright 2009 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form without the express written consent of
Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein. Tools required for
assembly and service may not be included.
For technical questions or replacement parts, please call 1-800-444-3353.
Download from Www.Somanuals.com. All Manuals Search And Download.
notice is used to
address practices
SaVe tHiS manual
Keep this manual for the safety warn-
ings and precautions, assembly, operat-
ing, inspection, maintenance and cleaning
procedures. Write the product’s serial
number in the back of the manual near the
assembly diagram (or month and year of
purchase if product has no number). Keep
this manual and the receipt in a safe and
dry place for future reference.
not related to personal injury.
caution, without
the safety alert
symbol, is used to address
practices not related to
personal injury.
general Power tool Safety
warnings
waRning Read all safety
warnings and instructions.
Failure to follow the warnings and
instructions may result in electric
shock, fire and/or serious injury.
Save all warnings and
instructions for future reference.
The term ″power tool″ in the
warnings refers to your mains-
operated (corded) power tool.
imPoRtant SaFetY
inFoRmation
in this manual, on the labeling,
and all other information provid-
ed with this product:
this is the safety alert
symbol. it is used to alert
you to potential personal
injury hazards. obey all
safety messages that
1. work area safety
a. keep work area clean and well lit.
Cluttered or dark areas invite acci-
dents.
follow this symbol to avoid
possible injury or death.
b. do not operate power tools in ex-
plosive atmospheres, such as in
the presence of flammable liquids,
gases or dust. Power tools create
sparks which may ignite the dust or
fumes.
dangeR indicates
a hazardous
situation which, if not
avoided, will result in death or
serious injury.
waRning
indicates a
hazardous situation which, if
not avoided, could result in
death or serious injury.
c. keep children and bystanders
away while operating a power
tool. Distractions can cause you to
lose control.
2. electrical safety
caution, used
with the safety
alert symbol, indicates a
hazardous situation which, if
not avoided, could result in
minor or moderate injury.
a. Power tool plugs must match the
outlet. never modify the plug in
any way. do not use any adapter
plugs with grounded power tools.
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Unmodified plugs and matching out-
lets will reduce risk of electric shock.
dust mask, non-skid safety shoes,
hard hat, or hearing protection used
for appropriate conditions will reduce
personal injuries.
b. avoid body contact with grounded
surfaces such as pipes, radiators,
ranges and refrigerators. There is
an increased risk of electric shock if
your body is grounded.
c. Prevent unintentional starting.
ensure the switch is in the off-
position before connecting to
power source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your finger
on the switch or energizing power
tools that have the switch on invites
accidents.
c. do not expose power tools to rain
or wet conditions. Water entering
a power tool will increase the risk of
electric shock.
d. do not abuse the cord. never use
the cord for carrying, pulling or
unplugging the power tool. keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk
of electric shock.
d. Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left at-
tached to a rotating part of the power
tool may result in personal injury.
e. do not overreach. keep proper
footing and balance at all times.
This enables better control of the
power tool in unexpected situations.
e. when operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduc-
es the risk of electric shock.
f. dress properly. do not wear
loose clothing or jewelry. keep
your hair, clothing and gloves
away from moving parts. Loose
clothes, jewelry or long hair can be
caught in moving parts.
f. if operating a power tool in a
damp location is unavoidable, use
a ground Fault circuit interrupter
(gFci) protected supply. Use of
a GFCI reduces the risk of electric
shock.
g. if devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of these devices can reduce
dust-related hazards.
3. Personal safety
a. Stay alert, watch what you are
doing and use common sense
when operating a power tool. do
not use a power tool while you
are tired or under the influence of
drugs, alcohol or medication. A
moment of inattention while operat-
ing power tools may result in serious
personal injury.
h. only use safety equipment that
has been approved by an appro-
priate standards agency. Unap-
proved safety equipment may not
provide adequate protection. Eye
protection must be ANSI-approved
and breathing protection must be
NIOSH-approved for the specific
hazards in the work area.
b. use personal protective equip-
ment. always wear eye protec-
tion. Safety equipment such as a
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Power tool use and care
into account the working condi-
tions and the work to be per-
formed. Use of the power tool
for operations different from those
intended could result in a hazardous
situation.
a. do not force the power tool. use
the correct power tool for your
application. The correct power tool
will do the job better and safer at the
rate for which it was designed.
b. do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be con-
trolled with the switch is dangerous
and must be repaired.
5. Service
a. Have your power tool serviced by
a qualified repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
c. disconnect the plug from the
power source and/or the battery
pack from the power tool before
making any adjustments, chang-
ing accessories, or storing power
tools. Such preventive safety mea-
sures reduce the risk of starting the
power tool accidentally.
Plunge Router Safety warnings
1. Hold power tool by insulated grip-
ping surfaces when performing an
operation where cutting tool may
contact hidden wiring or its own
cord. Contact with a ″live″ wire will
make exposed metal parts of the tool
″live″ and shock the operator.
d. Store idle power tools out of the
reach of children and do not allow
persons unfamiliar with the power
tool or these instructions to oper-
ate the power tool. Power tools are
dangerous in the hands of untrained
users.
2. use clamps or another practical
way to secure and support the
work piece to a stable platform.
Holding the work by hand or against
your body leaves it unstable and may
lead to loss of control.
e. maintain power tools. check for
misalignment or binding of mov-
ing parts, breakage of parts and
any other condition that may af-
fect the power tool’s operation. if
damaged, have the power tool re-
paired before use. Many accidents
are caused by poorly maintained
power tools.
3. Use only accessories rated at least
equal to maximum speed marked on
Router.
4. Only use router bits with a shank di-
ameter equal to the size of the tool’s
collet. The collet size is 1/4”.
f. keep cutting tools sharp and
clean. Properly maintained cutting
tools with sharp cutting edges are
less likely to bind and are easier to
control.
5. Make sure the collet nut is securely
tightened before use to prevent the
router bit from slipping during use.
6. Do not use with base removed.
7. Hold router with both hands.
g. use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Keep hands away from the cutting
area. Do not place hands beneath the
workpiece for any reason. Keep the
base of the router in firm contact with
the workpiece while cutting.
router will continue to operate while
the locking mechanism is engaged.
Do not lay the router down or hand it
to another person while the locking
mechanism is engaged.
9. Keep Handles dry, clean, and free of
oil or grease. This will permit better
control of the tool.
19. Before Routing, run the tool for about
10 seconds to ensure that all moving
parts are running smoothly and there
are no loose parts, rattles, or spark-
ing that would indicate damage.
10. Do not use damaged bits.
11. Do not lay the Router down until it
has stopped rotating completely.
20. Maintain labels and nameplates on
the tool. These carry important safety
information. If unreadable or miss-
ing, contact Harbor Freight Tools for a
replacement.
12. Hold the Router firmly when starting,
as startup rotation creates significant
torque.
21. Avoid unintentional starting. Prepare
to begin work before turning on the
tool.
13. Hold the Router firmly while cutting.
The action of the bit against the work-
piece can cause it to “kick out”, jump-
ing rapidly away from the workpiece.
This can be caused by an improper
type of bit, or a dull bit.
22. Do not lay the tool down until it has
come to a complete stop. Moving
parts can grab the surface and pull
the tool out of your control.
14. Do not handle the Router bit immedi-
ately after cutting. It may be very hot,
potentially causing burns or injury.
23. When using a handheld power tool,
maintain a firm grip on the tool with
both hands to resist starting torque.
15. Avoid overloading the tool. If the
speed drops abnormally, decrease
the pressure on the bit immediately.
Do not apply excessive pressure to
the router while cutting.
24. Do not leave the tool unattended
when it is plugged into an electrical
outlet. Turn off the tool, and unplug it
from its electrical outlet before leav-
ing.
16. Always use sharpened bits. If the bit
stops abruptly, or the bit becomes
blocked, remove the Router from the
workpiece and shut it off.
25. This product is not a toy. Keep it out
of reach of children.
26. People with pacemakers should
consult their physician(s) before use.
Electromagnetic fields in close prox-
imity to heart pacemaker could cause
pacemaker interference or pacemak-
er failure. In addition, people with
pacemakers should:
17. Do not start the Router while the bit
is in contact with the workpiece. Allow
the tool to reach its normal operating
speed before applying the bit to the
workpiece.
18. Use caution when setting the Lock-
ing Trigger Switch. Be aware that the
• Avoid operating alone.
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
• Do not use with power switch locked
on.
• Properly maintain and inspect to
avoid electrical shock.
• Any power cord must be properly
grounded. Ground Fault Circuit Inter-
rupter (GFCI) should also be imple-
mented – it prevents sustained elec-
trical shock.
ditions and situations that may occur.
It must be understood by the operator
that common sense and caution are
factors which cannot be built into this
product, but must be supplied by the
operator.
Vibration Safety
This tool vibrates during use. Re-
peated or long-term exposure to
vibration may cause temporary or
permanent physical injury, particularly
to the hands, arms and shoulders. To
reduce the risk of vibration-related
injury:
27. WARNING: Some dust created by
power sanding, sawing, grinding, drill-
ing, and other construction activities,
contains chemicals known [to the
State of California] to cause cancer,
birth defects or other reproductive
harm. Some examples of these
chemicals are:
1. Anyone using vibrating tools regu-
larly or for an extended period should
first be examined by a doctor and
then have regular medical check-
ups to ensure medical problems are
not being caused or worsened from
use. Pregnant women or people
who have impaired blood circulation
to the hand, past hand injuries, ner-
vous system disorders, diabetes, or
Raynaud’s Disease should not use
this tool. If you feel any symptoms
related to vibration (such as tingling,
numbness, and white or blue fingers),
seek medical advice as soon as pos-
sible.
• Lead from lead-based paints
• Crystalline silica from bricks and ce-
ment or other masonry products
• Arsenic and chromium from chemi-
cally treated lumber
Your risk from these exposures var-
ies, depending on how often you do
this type of work. To reduce your
exposure to these chemicals: work in
a well ventilated area, and work with
approved safety equipment, such as
those dust masks that are specially
designed to filter out microscopic
particles. (California Health & Safety
Code § 25249.5, et seq.)
2. Do not smoke during use. Nico-
tine reduces the blood supply to the
hands and fingers, increasing the risk
of vibration-related injury.
28. WARNING: Handling the cord on
this product will expose you to lead,
a chemical known to the State of
California to cause cancer, and birth
defects or other reproductive harm.
Wash hands after handling. (Califor-
nia Health & Safety Code § 25249.5,
et seq.)
3. Wear suitable gloves to reduce the
vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
29. The warnings, precautions, and in-
structions discussed in this instruction
manual cannot cover all possible con-
5. Include vibration-free periods each
day of work.
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Grip tool as lightly as possible (while
still keeping safe control of it). Let
the tool do the work.
grounded tools: tools with three
Prong Plugs
7. To reduce vibration, maintain the tool
as explained in this manual. If any
abnormal vibration occurs, stop use
immediately.
SaVe tHeSe
inStRuctionS.
3-Prong Plug and outlet
gRounding
1. Tools marked with “Grounding Re-
quired” have a three wire cord and
three prong grounding plug. The
plug must be connected to a properly
grounded outlet. If the tool should
electrically malfunction or break
down, grounding provides a low
resistance path to carry electricity
away from the user, reducing the risk
of electric shock. (See 3-Prong Plug
and outlet.)
to PReVent
electRic SHock
and deatH FRom
incoRRect gRounding
wiRe connection:
Check with a qualified
electrician if you are in doubt
as to whether the outlet is
properly grounded. do not
modify the power cord plug
provided with the tool. never
remove the grounding prong
from the plug. do not use the
tool if the power cord or plug
is damaged. if damaged, have
it repaired by a service facility
before use. if the plug will not
fit the outlet, have a proper
outlet installed by a qualified
electrician.
2. The grounding prong in the plug is
connected through the green wire in-
side the cord to the grounding system
in the tool. The green wire in the cord
must be the only wire connected to
the tool’s grounding system and must
never be attached to an electrically
“live” terminal. (See 3-Prong Plug
and outlet.)
3. The tool must be plugged into an
appropriate outlet, properly installed
and grounded in accordance with all
codes and ordinances. The plug and
outlet should look like those in the
preceding illustration. (See 3-Prong
Plug and outlet.)
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
3. The smaller the gauge number of the
wire, the greater the capacity of the
cord. For example, a 14 gauge cord
can carry a higher current than a 16
gauge cord. (See table a.)
double insulated tools: tools
with two Prong Plugs
4. When using more than one exten-
sion cord to make up the total length,
make sure each cord contains at
least the minimum wire size required.
(See table a.)
outlets for 2-Prong Plug
5. If you are using one extension cord
for more than one tool, add the
nameplate amperes and use the sum
to determine the required minimum
cord size. (See table a.)
1. Tools marked “Double Insulated” do
not require grounding. They have
a special double insulation system
which satisfies OSHA requirements
and complies with the applicable
standards of Underwriters Labora-
tories, Inc., the Canadian Standard
Association, and the National Electri-
cal Code. (See outlets for 2-Prong
Plug.)
6. If you are using an extension cord
outdoors, make sure it is marked with
the suffix “W-A” (“W” in Canada) to
indicate it is acceptable for outdoor
use.
7. Make sure the extension cord is prop-
erly wired and in good electrical con-
dition. Always replace a damaged
extension cord or have it repaired by
a qualified electrician before using it.
2. Double insulated tools may be used
in either of the 120 volt outlets shown
in the preceding illustration. (See
outlets for 2-Prong Plug.)
8. Protect the extension cords from
sharp objects, excessive heat, and
damp or wet areas.
extension cords
1. Grounded tools require a three wire
extension cord. Double Insulated
tools can use either a two or three
wire extension cord.
2. As the distance from the supply outlet
increases, you must use a heavier
gauge extension cord. Using exten-
sion cords with inadequately sized
wire causes a serious drop in voltage,
resulting in loss of power and pos-
sible tool damage.
(See table a.)
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Recommended minimum wiRe
gauge FoR extenSion coRdS*
(120/240 Volt)
extenSion coRd
namePlate
lengtH
amPeReS
(at full load)
0 – 2.0
2.1 – 3.4
18
18
18
18
18
14
12
18
18
18
16
14
12
10
18
18
16
14
12
10
-
18
16
14
12
10
-
16
14
12
12
-
3.5 – 5.0
5.1 – 7.0
7.1 – 12.0
12.1 – 16.0
16.1 – 20.0
-
-
-
* based on limiting the line
voltage drop to five volts at
150% of the rated amperes.
table a
Symbology
Double Insulated
Canadian Standards Association
Underwriters Laboratories, Inc.
Volts Alternating Current
Amperes
V~
a
No Load Revolutions per Minute
(RPM)
n xxxx/min.
0
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
note: For additional information regarding the
parts listed in the following pages, refer
to the Assembly Diagram near the end of
this manual.
SPeciFicationS
Power
1-1/2 HP
Electrical Input
Motor Speed
120 V~ / 60 Hz / 10 A
11,000 - 28,000 RPM (No
Load)
Functions
Collet Capacity 1/4”
Depth
of Cut
Scale
Maximum
Plunge
Adjusting
Knob (26)
2-1/8”
Speed Adjuster (4)
Depth
Measurements
Pointer
(28)
1/16” increments
4-stage turret stop
Depth Stop
93ma
Spindle
Lock
Button
(46)
Depth
Stop Bar
(30)
e194601
Thumb
Screw
Depth
Stop
unPacking
Spindle
Turret
(67)
When unpacking, make sure that the
item is intact and undamaged. If any parts are
missing or broken, please call Harbor Freight
Tools at 1-800-444-3353 as soon as possible.
Collet Nut (50)
Chip Shield (70)
Thumb Screw (81)
Trigger
Switch
(60)
inStRuctionS FoR
Putting into uSe
Lock-on Button
Read the entiRe imPoRtant
SaFetY inFoRmation
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
Plunge Lock
Lever (32)
Thumb
Screw
(81)
Dust Extraction
Adapter
to PReVent
SeRiouS injuRY
Base Plate
FRom accidental
oPeRation:
Spanner
Wrench (51)
turn the Power Switch of the
tool off and unplug the tool
from its electrical outlet
before set up, assembly, or
making any adjustments to
the tool.
Edge Guide
Figure 1
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
place. Keep the Spindle Lock Button
depressed through step 6.
oPeRating inStRuctionS
Read the entiRe imPoRtant
SaFetY inFoRmation
section at the beginning of this
manual including all text under
subheadings therein before set
up or use of this product.
4. Use the Spanner Wrench (51) to
loosen the Collet Nut (50).
5. Insert the bit all the way into the
Collet. caution! bits are sharp,
Handle with care.
6. Securely tighten Collet Nut.
tool Set up
7. Release the Spindle Lock Button.
to PReVent
SeRiouS injuRY
FRom accidental
oPeRation:
8. Pull up the Lock Lever to free the
shaft.
turn the Power Switch of the
tool off and unplug the tool
from its electrical outlet
before preparing for
operation.
9. Replace the Chip Shield.
cutting depth adjustment
Depth
Stop
Bar (30)
installing bits
Spindle Lock Button (46) Spindle
Depth
Adjusting
Bolt (29)
Depth
of Cut
Depth
Stop
Turret
Chip
Shield
(70)
(67)
Screw
(85)
Collet Nut (50)
Figure 3
Figure 2
The depth of cut is equal to the dis-
tance between the lower end of the
Depth Adjusting Bolt (29) and the
section of the Depth Stop Turret (67)
directly below the Depth Stop Bar
(30). First, install the bit you will use
for the cut, then adjust the Router as
follows to set up the desired cutting
depth.
1. Unthread the Screw (85) holding the
Chip Shield (70) in place and remove
the Chip Shield.
2. Lock the Plunge Lock Lever (32) in
place to keep the shaft stationary.
3. Depress the Spindle Lock Button (46)
and rotate the Spindle until it locks in
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Loosen the Thumb Screw so that the
Depth Stop Bar (30) can slide freely.
Stop Turret (67). Slide the Pointer
(28) to zero on the Increment Guide,
then raise the Depth Stop Bar to the
desired height using the Pointer and
the Increment Guide. Tighten the
Thumb Screw to hold the Stop Bar in
place.
2. Rotate the Adjusting Knob (26) until
the Depth Adjusting Bolt (29) pro-
trudes about 1/4” from the Depth
Stop Bar.
3. Rotate the Depth Stop Bar to the left
so that the indexing mark along the
top of the Bar is visible from under
the Pointer (28).
• Or, using a piece of wood the thick-
ness of the desired cut, place the
piece of wood on the Lowest level
of the Depth Stop Turret (67). Adjust
the Depth Stop Bar (29) so that the
Depth Stop Bolt (29) rests on the
piece of wood and tighten in place
with the Thumb Screw.
4. Hold the Bar and rotate the Adjust-
ing Knob until the Zero mark along
the base of the adjusting Knob aligns
with the indexing line.
note: For marginal depth adjustments,
raise the Depth Adjusting Bolt (29)
(located inside the Depth Stop Bar)
in fine increments by turning the
Adjusting Knob (26) to set the exact
desired depth of cut. Use the Pointer
(28) along with the increment guide to
help make the adjustment.
5. Rotate the Depth Stop Turret (67) to
the lowest setting.
6. Loosen the Plunge Lock Lever (32).
7. Lower the Router body until the bit
just touches the workpiece.
8. Tighten the Plunge Lock Lever.
10. Loosen the Plunge Lock Lever and
allow the router to return to its original
position.
9. Use one of the following two ways to
adjust the router depth:
Adjusting
Knob (26)
Increment Guide
edge guide
Thumb Screws (81)
Depth
Stop
Bar
Pointer
(28)
(30)
Bars
Fence
Edge Guide
Figure 5
Thumb Screw
To attach the Edge Guide when mak-
ing straight cuts:
Figure 4
• Position the Depth Adjusting Bolt
a. Loosen the Thumb Screws (81).
(29), so that it is touching the Depth
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Slide the bars on the Edge Guide
into the slots on the Base of the
Router with the fence facing the
workpiece.
The power cord must reach the work
area with enough extra length to al-
low free movement while working.
3. Secure loose work pieces using a
vise or clamps (not included) to pre-
vent movement while working.
note: The Edge Guide can be inserted
into either side of the tool to make
cuts along the left or right side of the
material.
4. Make sure there are no metal objects
in the wood which might make con-
tact with the router bit.
c. Adjust the distance between the
router bit and the fence of the Edge
Guide to the desired setting.
5. Hold Router handles firmly with both
hands.
d. Tighten the Thumb Screws (81).
6. Always hold the Router from the
front, ensuring that the Chip Shield
(70) is between you and the bit.
dust extraction adapter
1. If desired, attach a vacuum cleaner
hose to the Dust Extraction Adapter
(62).
7. Keep hands away from rotating bit.
Unplug the tool and wait until the bit
stops rotating completely before mak-
ing adjustments.
2. Be sure the hose, vacuum cleaner,
and power cord are out of the way
and properly secured so they will not
tip over or interfere with the Router
or workpiece. If they cannot be posi-
tioned safely, they should not be used
with the Router.
8. Do not touch the bit right after cutting.
It becomes very hot.
9. Before cutting material, turn the
Router on. Watch and feel for vibra-
tion which could indicate an improp-
erly installed bit.
3. Turn on the vacuum before turning on
the Router.
10. Turn the Router off when not actually
cutting. Do not leave running.
4. Empty the vacuum cleaner as need-
ed only after turning off and unplug-
ging both the vacuum cleaner and the
Router.
general operating instructions
note: Use two or more passes for deep
cuts, especially in the case of hard-
wood. Do not attempt to cut deeper
than 5/8” in a single pass. Turn the
Depth Stop Turret (67) so that the
first pass will be less than 5/8” deep,
then rotate the Turret one step for
each progressive pass, until the final
depth is achieved.
work Piece and work area Set up
1. Designate a work area that is clean
and well-lit. The work area must not
allow access by children or pets to
prevent distraction and injury.
2. Route the power cord along a safe
route to reach the work area without
creating a tripping hazard or exposing
the power cord to possible damage.
caution: When first turning on the
Router, grip the Handles firmly as the
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
tool may try to twist from the strong
initial torque.
switches, depress and hold in the
Trigger Switch (60), then push the
Lock-on Button. Release the Trig-
ger Switch, then the Lock-on Button.
To stop the Router from this setting,
press and release the Trigger Switch.
note: The Router bit should always be fed
into the stock from left to right so as
to match the clockwise rotation of the
router. When cutting outside edges,
rotate the router counterclockwise.
Rotate it clockwise when cutting in-
side edges.
5. Allow the bit to come to full speed,
slowly engage material. DO NOT
force the Router down into the mate-
rial.
note: Make practice cuts at different
speeds in scrap material until you are 6. When the tool reaches its pre-set
able to produce a smooth cut with no
burnishing or burn marks. Burn marks
are caused by moving too slowly
through the wood. Feeding the Rout-
er too quickly, or trying to remove too
much material in a single pass cre-
ates a rough cut and can overload
the motor.
depth, tighten the Plunge Lock Lever
(32).
7. Once you have finished the cut, loos-
en the Plunge Lock Lever and allow
the spring to lift the Router directly
out of the workpiece.
8. When finished, raise the Router so
the bit is clear of the material, then
release the Trigger Switch, or press
and release the Trigger Switch if the
Lock-on Button was set. Do not set
the Router down until the bit has
come to a complete stop.
1. Set the desired speed by turning the
Speed Adjuster (4). Use lower set-
tings for large diameter bits and high-
er settings for small diameter bits.
2. Place the Router directly above the
point you plan to cut. Verify that there
are no obstructions in the cutting
path.
9. When making more than one pass
to achieve the desired cutting depth,
turn the Depth Stop Turret to the next
lower level and repeat the cut. Re-
peat again as needed until the cut is
the desired depth.
3. Verify that the Plunge Lock Lever (32)
is loose.
4. Turn on the Router. The Router can
be powered with or without the Lock- 10. To prevent accidents, disconnect the
on Button engaged.
power supply after use. Clean, then
store the tool indoors out of children’s
reach.
• To power the Router so that the
power is on only while the Trigger
Switch is depressed: depress and
hold in the Trigger Switch (60). To
stop the Router from this setting,
release the Trigger Switch.
• To power the Router continuously,
without holding in any buttons or
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
soft brush and/or blowing clear with
compressed air.
maintenance and
SeRVicing
4.
waRning! if the supply cord of
this power tool is damaged, it must
be replaced only by a qualified
service technician.
Procedures not specifically
explained in this manual
must be performed only by a
qualified technician.
to PReVent
SeRiouS injuRY
FRom accidental
oPeRation:
turn the Power Switch of the
tool off and unplug the tool
from its electrical outlet
before performing any
inspection, maintenance, or
cleaning procedures.
to PReVent SeRiouS
injuRY FRom tool
FailuRe:
do not use damaged
equipment. if abnormal noise
or vibration occurs, have the
problem corrected before
further use.
cleaning, maintenance, and
lubrication
1. beFoRe eacH uSe, inspect the
general condition of the tool. Check
for loose hardware, misalignment or
binding of moving parts, cracked or
broken parts, damaged electrical wir-
ing, and any other condition that may
affect its safe operation.
2. aFteR uSe, wipe external surfaces
of the tool with a clean cloth. Do not
use any abrasive or solvent-based
cleaners.
3. Regularly clean all ventilation open-
ings by periodically brushing with a
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
troubleshooting
Problem
Tool will not start.
Possible causes
1. Cord not connected.
likely Solutions
1. Check that cord is plugged in.
2. No power at outlet.
2. Check power at outlet. If outlet is
unpowered, turn off tool and check circuit
breaker. If breaker is tripped, make sure
circuit is right capacity for tool and circuit
has no other loads.
3. Tool’s thermal reset breaker
tripped (if equipped).
3. Turn off tool and allow to cool. Press
reset button on tool.
4. Internal damage or wear.
(Carbon brushes or switch, for
example.)
4. Have technician service tool.
Tool operates slowly. Power being reduced by long or
small diameter extension cord.
Eliminate use of extension cord. If an
extension cord is needed, use one with the
proper diameter for its length and load. See
Extension Cords in GROUNDING section.
1. Keep cutting accessories sharp.
Replace as needed.
Performance
1. Accessory dull or damaged.
decreases over time.
2. Carbon brushes worn or
damaged.
2. Have qualified technician replace
brushes.
Excessive noise or Internal damage or wear. (Carbon
Have technician service tool.
rattling.
Overheating.
brushes or bearings, for example.)
1. Forcing tool to work too fast.
1. Allow tool to work at its own rate.
2. Accessory misaligned.
2. Check and correct accessory to fence
and/or table alignment.
3. Accessory dull or damaged.
4. Blocked motor housing vents.
3. Keep cutting accessories sharp.
Replace as needed.
4. Wear ANSI-approved safety goggles and
NIOSH-approved dust mask/respirator
while blowing dust out of motor using
compressed air.
5. Motor being strained by long or
small diameter extension cord.
5. Eliminate use of extension cord. If
an extension cord is needed, use one
with the proper diameter for its length
and load. See Extension Cords in
GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing the
tool. disconnect power supply before service.
PleaSe Read tHe Following caReFullY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS qUALIFIED
TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANY PARTS
OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLY STATES THAT
ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED
TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT
OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
PaRtS liSt
Part
description
Qty
8
1
2
1
5
2
1
1
2
2
2
2
1
1
1
1
1
2
1
3
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
5
5
1
1
4
1
Part
description
Qty
2
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
2
1
2
2
1
1
1
1
1
1
1
2
1
3
1
2
1
2
2
2
3
2
1
2
1
1
2
3
4
5
6
7
8
9
Tapping Screw
Cover
Screw
44 Spring
45 Spindle Lock
46 Spindle Lock Button
47 Lock Cover
48 Screw
49 Collet
50 Collet Nut
51 Collet Wrench
52 Inner Wire
53 Right Handle Cover
54 Right Handle
55 Cord Anchor
56 Screw
57 Cord Guard
58 Power Cord and Plug
59 Cover
Speed Adjuster
Tapping Screw
Tapping Screw
Cover
Cover
Tapping Screw
10 Epoxy Board
11 Brush Holder
12 Carbon Brush
13 Motor Housing
14 Spring
15 Washer
16 Bearing
17 Stator
18 Tapping Screw
19 Rotor
20 Circlips for Shaft
21 Fan Baffle
22 Screw
23 Bearing Clamping Plate
24 Ball Bearing 608 R5
25 Screw
26 Adjusting Knob
27 O-Ring
28 Depth Indicator
29 Depth Adjusting Bolt
30 Depth Stop Bar
31 Screw
32 Plunge Lock Lever
33 Slotted Set Screw
34 Wave Washer
35 Nut
36 Left Handle Cover
37 Hexagon Socket Screw
38 Spring Washer
39 Plain Washer
40 Left Handle
41 Plunge Frame
42 Tapping Screw
43 Nut
60 Switch
61 Spring
62 Dust Extraction Adapter
63 Hexagon Nut
64 Bellows Seal
65 Screw 4mm x 0.7
66 Waver Washer
67 Depth Stop Turret
68 Steel Ball Ø 5mm
69 Spring
70 Chip Shield
71 Bottom Support
72 Guiding Rod
73 Base Plate
74 Screw
75 Guide Bushing
76 Screw
77 Parallel Guide
78 Plain Washer
79 Spring Washer
80 Screw
81 Thumb Screw
82 Spring Pin
83 Lower Cover
84 Plunge Rod
85 Screw, Chip Shield 4mm x 0.7
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
aSSemblY diagRam
Record Product’s Serial number Here:
note: If product has no serial number, record month and year of purchase instead.
note: Some parts are listed and shown for illustration purposes only, and are not avail-
able individually as replacement parts.
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
limited 90 daY waRRantY
Harbor Freight Tools Co. makes every effort to assure that its products meet high
quality and durability standards, and warrants to the original purchaser that this prod-
uct is free from defects in materials and workmanship for the period of 90 days from
the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance.
We shall in no event be liable for death, injuries to persons or property, or for incidental,
contingent, special or consequential damages arising from the use of our product. Some
states do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS ExPRESS-
LY IN LIEU OF ALL OTHER WARRANTIES, ExPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with
transportation charges prepaid. Proof of purchase date and an explanation of the com-
plaint must accompany the merchandise. If our inspection verifies the defect, we will ei-
ther repair or replace the product at our election or we may elect to refund the purchase
price if we cannot readily and quickly provide you with a replacement. We will return re-
paired products at our expense, but if we determine there is no defect, or that the defect
resulted from causes not within the scope of our warranty, then you must bear the cost
of returning the product.
This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353
SKU 67119
For technical questions, please call 1-800-444-3353.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
|