User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Table of Contents
1. Before You Begin...............................................................................................1
Unpacking Instructions................................................................................................... 1
Icon Meaning................................................................................................................. 1
Safety Notes.................................................................................................................. 2
2. Introduction........................................................................................................3
Product Dimensions....................................................................................................... 5
DMX Modes...........................................................................................................................7
4. Operation............................................................................................................9
Control Options.............................................................................................................. 9
Programming................................................................................................................. 9
Master/Slave........................................................................................................................10
Software Version..................................................................................................................10
Keylock................................................................................................................................10
Fan......................................................................................................................................10
Reset...................................................................................................................................10
Reset Control.......................................................................................................................11
Fan Control..........................................................................................................................12
White Calibration..................................................................................................................13
System Default.....................................................................................................................13
ADVANCED.........................................................................................................................17
Q-Wash 360Z-LED User Manual Rev. 01g
-a-
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
5. Technical Information......................................................................................18
Returns Procedure........................................................................................................20
-b-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
1. Before You Begin
·
·
·
·
·
·
One Q-Wash 360Z-LED
What is
Included
One IEC power cord with Edison plug (US market)
One safety cable
Two omega brackets
Warranty Card
Quick Reference Guide
Immediately upon receiving this product, carefully unpack it and check the container in
which you received it. Make sure that you have received all the parts indicated above and
that they are all in good condition. If the material inside the container (this product and any
other accessory included with it) appears damaged from shipping, or if the container shows
signs of mishandling, notify the shipper immediately. In addition, retain the container and
all the packing material for inspection.
Unpacking
Instructions
See the Claims section in the Technical Information chapter.
Convention
1~512
Meaning
Typographic
Conventions
A range of values in the text
50/60
A set of mutually exclusive values in the text
A new term, or a section or chapter in this document
Claims
“COLORado™ 1 UM” The name of another publication or manual
<SET>
Settings
MENU > Settings
1~10
A button on the fixture’s control panel
A fixture function or a menu option
A sequence of menu options
A range of menu values from which to choose in a menu
A set of two mutually exclusive menu options in a menu
A unique value to be entered or selected in a menu
Yes/No
ON
Icon
Meaning
Icon Meaning
This icon indicates critical installation, configuration, or operation
information. Failure to comply with this information may render the
fixture partially or completely inoperative, damage third-party
equipment, or cause harm to the user.
This icon indicates important installation or configuration
information. Failure to comply with this information may prevent
the fixture from functioning correctly.
This icon indicates useful, although non-critical information.
The term “DMX” used throughout this document refers to the USITT DMX512-A
transmission protocol.
Use on Dimmer
Outdoor Use
Sound Activated
DMX
Auto Programs
x
x
x
P
P
P
P
x
Product at a
Glance
Auto-ranging Power Supply
Replaceable Fuse
User Serviceable
Duty Cycle
Master/Slave
x
P
Q-Wash 360Z-LED User Manual Rev. 01g
-1-
Download from Www.Somanuals.com. All Manuals Search And Download.
Before You Begin
Please read the following notes carefully because they include important safety
information about the installation, usage, and maintenance of this product.
Safety Notes
It is important to read all these notes before starting to work with this product.
There are no user serviceable parts inside this product. Any reference to servicing
it you may find from now on in this User Manual will only apply to properly
CHAUVET® certified technicians. Do not open the housing or attempt any repairs
unless you are one of them.
Please refer to all applicable local codes and regulations for the proper installation
of this product.
Personal Safety
·
·
·
·
Avoid direct eye exposure to the light source while the fixture is on.
Always disconnect this product from its power source before servicing.
Always connect this product to a grounded circuit to avoid the risk of electrocution.
Do not touch this product’s housing when operating because it may be hot.
Mounting and Rigging
·
This product is for indoor use only! To prevent risk of fire or shock, do not expose this
product to rain or moisture.
·
·
Make sure there are no flammable materials close to this product while operating.
When hanging this product, always secure it to a fastening device using a safety cable
(included).
·
·
Do not carry this fixture from the head; use the handles instead.
Power and Wiring
Operation
Always make sure that you are connecting this product to the proper voltage, as per
the specifications in this manual or on the product’s sticker.
·
·
Never connect this product to a dimmer pack or rheostat.
Never disconnect this product by pulling or tugging on the power cable.
·
·
·
·
·
Do not operate this fixture if you see damage on the housing, lenses, or cables. In any
of these cases, have the damaged parts replaced by an authorized technician at once.
Do not cover the ventilation slots when the fixture is operating to avoid internal
overheating.
Do not aim this fixture toward the Sun. Otherwise, the lenses could concentrate the
solar energy and cause internal overheating.
The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this product
at a higher temperature.
In case of a serious operating problem, stop using this product immediately!
In the unlikely event that your CHAUVET® product may require service, please
contact CHAUVET® Technical Support.
LEDs gradually decline in brightness over time, mostly because of heat. Packaged in
clusters, LEDs exhibit higher operating temperatures than in ideal, single LED conditions.
For this reason, using clustered LEDs at their fullest intensity significantly reduces the
LEDs’ lifespan. Under normal conditions, this lifespan can be of 40,000 to 50,000 hours. If
extending this lifespan is vital, lower the operational temperature by improving the fixture’s
ventilation and reducing the external temperature. In addition, limiting the overall
projection intensity may also help to extend the LEDs’ lifespan.
Expected LED
Lifespan
-2-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
2. Introduction
The Q-Wash 360Z-LED is an RGBW LED moving yoke, wash fixture.
Product
Description
It consists of a base section and a moving yoke with a pan range of up to 540º. The
moving head, which has a tilt range of 270º, contains the 91 RGBW LEDs and the zoom
motors. The base section has the 3- and 5-pin DMX input and output sockets, the IEC
power input connector and the LCD based control panel.
·
·
·
·
·
·
·
·
·
·
·
·
·
·
·
11 or 15-channel
Features
Pan: 540°
Tilt: 270°
RGBW color static mixing with or without DMX control
Continuously variable zoom (9º~26°)
Electronic strobe (0~20 Hz)
Electronic dimmer (0~100%).
High power setting
Built-in automated programs
Remote fixture reset and vector speed channel
255-step fully customizable program
Recall auto or custom programs via control panel or DMX
Color temperature presets (3,200~10,000 K)
Color calibration
Fan speed control
·
·
3- and 5-pin DMX input and output connectors
LCD display with password protection
Additional
Features
Q-Wash 360Z-LED User Manual Rev. 01g
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
3. Setup
The Q-Wash 360Z-LED has an auto-ranging power supply that can work with an input
voltage range of 100~240 VAC, 50/60 Hz.
AC Power
Make sure that you are connecting this product to the proper voltage, as per the
specifications in this guide, the product’s user manual, or on the product’s sticker.
Always connect this product to a protected circuit with an appropriate electrical
ground to avoid the risk of electrocution or fire.
To determine the power requirements for the Q-Wash 360Z-LED see the label affixed to
the side of the fixture. Alternatively, you may refer to the Technical Specifications chart in
the Technical Information chapter of this manual.
The listed current rating indicates the maximum current draw during normal operation. For
more information, you may download the “Sizing the Circuit Breakers” document from the
CHAUVET® Web site.
Never connect this product to a rheostat (variable resistor) or dimmer circuit, even if
the rheostat or dimmer channel serves only as a 0 to 100% switch.
The Q-Wash 360Z-LED comes with a power input cord terminated with an IEC connector
on one end an Edison plug on the other end (US market). If the power input cord that came
with your product has no plug or you need to change the Edison plug, use the table below
to wire the new plug.
AC Plug
Connection
AC Live
Wire (US)
Black
Wire (Europe)
Brown
Screw Color (US)
Yellow or Brass
Silver
AC Neutral
AC Ground
White
Blue
Green/Yellow
Green/Yellow
Green
Make sure to disconnect the fixture’s power cord before replacing a blown fuse, and
always replace it with a fuse of the same type and rating.
1) Wedge the tip of a flat head screwdriver into the slot of the fuse holder and pry it out of
its housing.
Fuse Replacement
2) Remove the blown fuse from its holder and replace it with a fuse of the exact same
type and rating (T 5 A, 250 V).
2) Insert the fuse holder back in its place, and reconnect power.
The fuse is located
inside this compartment.
Remove it using a flat
head screwdriver.
-6-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
You may link the Q-Wash 360Z-LED to a DMX controller using a standard DMX serial
connection. If using other DMX compatible fixtures with this product, it is possible to control
DMX Linking
them individually with a single DMX controller.
If you are not familiar with the DMX standard, or if you need information about the DMX
cables needed to link this product to a DMX controller, you may download the “DMX
Primer” document from the CHAUVET® Web site.
The Q-Wash 360Z-LED uses the standard DMX data connection for its Basic and
Advanced DMX modes. You will find information about these DMX modes in the Operation
chapter (configuration details), and the DMX Values section (individual channel values).
DMX Modes
The Master/Slave mode allows a Q-Wash 360Z-LED fixture to control one or more fixtures
of the same model without a DMX controller. The controlling fixture becomes the “master
fixture” when running the Auto1, Auto2, or Custom programs. You must configure the
controlled (slave) fixtures to operate in “SLAVE” mode from their respective control panels.
During the Master/Slave operation, the slave fixtures will operate in unison with the master
fixture.
Master/Slave
Connectivity
The master links to the slave fixtures using the standard DMX serial connection. If you are
not familiar with the Master/Slave connectivity, you may download the “DMX Primer”
document from the CHAUVET® Web site.
DO NOT connect a DMX controller to the fixtures operating in Master/Slave mode.
Otherwise, the signals from the DMX controller may interfere with the signals from
the master fixture.
The Operation chapter of this manual provides detailed instructions on how to
configure the Master and Slave units.
Q-Wash 360Z-LED User Manual Rev. 01g
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Before mounting this product, read and follow the safety recommendations indicated in the
Safety Notes section (page 2 of this manual).
Mounting
Always mount this product in any safe position while making sure that there is adequate
room around it for ventilation, head motion, configuration, and maintenance.
Orientation
Rigging
CHAUVET® recommends following the general guidelines below when mounting this
product.
·
·
·
·
When selecting an installation location, consider ease of access to the fixture for
operation, programming adjustments, and routine maintenance.
Make sure to mount this product away from any flammable material, as indicated in the
Safety Notes section, or obstructions that may block the moving head.
Never mount the product in places where rain, high humidity, extreme temperature
changes, or restricted ventilation may affect it.
If hanging this product, make sure that the location where you are mounting it can
support its weight. Please see the Technical Specifications section of this manual for
the weight requirement of this fixture.
Procedure
The Q-Wash 360Z-LED comes with two omega brackets to which you can attach “C” or “O”
clamps. You must supply your own “C” or “O” clamps and make sure that they are capable
of supporting the weight of this fixture. You will have to use two mounting points per fixture.
The omega brackets also serve to anchor this product to a panel. For floor standing
operation, this product has built-in rubber feet.
Safety Cable (included)
C clamp (not included)
Omega bracket (included)
Product Mounting
Diagram
Overhead Mounting
Floor Standing
-8-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
4. Operation
Function
Exits from the current menu or function
Button
Control Panel
Description
<MENU>
Enables the currently displayed menu or sets the currently selected value
in to the current function
<ENTER>
<UP>
Navigates upwards through the menu list and increases the numeric value
when in a function
Navigates downwards through the menu list and decreases the numeric
value when in a function
<DOWN>
You can set the Q-Wash 360Z-LED start address in the 001~512 DMX range. This allows
for the control of up to 34 fixtures in the 15-channel ADVANCED personality.
Control Options
Programming
Refer to the Menu Map on page 14 to learn how the menu options relate to each other.
The menu map has a Menu Level and a variable number of programming levels for each
option.
To go to an option in the Menu Level, press <MENU> repeatedly until the option shows on
the display. Press <ENTER> to select it. This will take you to the first programming level for
that option.
To select an option or value within the current programming level press <UP> or <DOWN>
until it shows on the display. Press <ENTER> to accept it. In this case, if there is another
programming level, you will see its first option. Otherwise, you will see the selected value.
To exit to the previous menu level, press <MENU>.
In the EDIT menu, <UP> and <DOWN> will only change the value of the current
option. To change to the next option, press <ENTER>.
1) Select DMX operation.
DMX Operation
a) Go to MENU > INTRO > RUN.
b) Select DMX512.
2) Select a DMX mode.
a) Go to MENU > INTRO > CHANNELS.
b) Select BASIC or ADVANCED.
3) Select the starting address.
a) Go to MENU > INTRO > ADDRESS.
b) Select a starting address, 001~498 (Advanced) or 001~502 (Basic).
The highest recommended starting address for each of the two DMX modes are as
follows:
BASIC:
502
ADVANCED: 498
1) Go to MENU > INTRO > RUN.
Stand-alone
Operation
2) Select a stand-alone operation mode (AUTO 1, AUTO 2, CUSTOM, or TEST).
Of all the stand-alone operation modes indicated above, only “CUSTOM” is editable
(see Edit Custom).
Continues on the next page
Q-Wash 360Z-LED User Manual Rev. 01g
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
The Master/Slave mode allows a group of Q-Wash 360Z-LED fixtures (the slaves) to
simultaneously duplicate the output of another Q-Wash 360Z-LED (the master), whether
static mode settings or auto/custom programs, without a DMX controller.
Master/Slave
1) Set the master unit:
a) Select a stand-alone mode, as indicated above.
2) Set each of the slave units:
a) Go to MENU > INTRO > RUN.
b) Select SLAVE.
·
·
Do not connect a DMX controller to the master or slave fixtures.
The master unit should be the first in the DMX string.
This mode defines how the LCD’s backlight will work.
1) Go to MENU > INTRO > DISPLAY.
Display Mode
2) Select a display mode (60 CLOSE or BRIGHT).
·
·
When in the “60 CLOSE” setting, the LCD’s backlight will turn off after 60 s.
When in the “BRIGHT” setting, the LCD’s backlight will stay on.
This option will show the installed software version.
1) Go to MENU > INTRO > INFO.
Software Version
Keylock
2) The display will show Edition.
3) Press <ENTER> to see the installed software version.
This option enables or disables the LCD key.
1) Go to MENU > INTRO > KEYLOCK.
2) Select YES or NO.
When in the “YES” setting, the user will have to enter the password after 30 seconds
of control panel inactivity or each time he/she turns the fixture on.
The default (non-modifiable) password is
<UP>, <DOWN>, <UP>, <DOWN>, and <ENTER>.
You can select the fan operation mode, as follows:
1) Go to MENU > INTRO > FAN.
Fan
2) Select HIGH, NORMAL, LOW, or AUTO.
The fixture’s controller will force the fan to High if the fixture’s internal temperature
becomes too high, despite any manual or DMX setting.
This option allows you to reset all custom settings to their default values.
1) Go to MENU > INTRO > RESET.
Reset
2) Select YES or NO.
Continues on the next page
-10-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
To select the dimmer curve, do the following:
1) Go to MENU > INTRO > DIMMER.
2) Select DIMMER0~4.
Dimmer Curve
DIMMER0:
The output is proportional (linear) to the Dimmer and RGBW channel
values.
DIMMER1~4:
The output follows the Dimmer and RGBW channel values based on the
corresponding dimmer curve, being DIM1 the fastest and DIM4 the
slowest.
This option allows you to define how the pan, tilt, and dimmer increase based on the
direction you move the corresponding fader.
Fader Reversal
1) Go to MENU > INVERT > PAN.
2) Select a fader direction (NORMAL or REVERSE).
3) Go to MENU > INVERT > TILT.
4) Select a fader direction (NORMAL or REVERSE).
5) Go to MENU > INVERT > DIMMER.
6) Select a fader direction (NORMAL or REVERSE).
7) Go to MENU > INVERT > USE.
8) Select YES to activate the new settings or NO to stop using them.
·
·
When in NORMAL, the pan, tilt, and dimmer values will increase as the position
of the respective fader increases.
When in REVERSE, the pan, tilt, and dimmer values will decrease as the position
of the respective fader increases.
When it is necessary to limit the pan or tilt range, you can do the following:
1) Go to MENU > RANGE > P/START.
Range Limitation
2) Select the starting point for the limited pan (000~255).
3) Go to MENU > RANGE > P/FINISH.
4) Select the finishing point for the limited pan (000~255).
5) Go to MENU > RANGE > T/START.
6) Select the starting point for the limited tilt (000~255).
7) Go to MENU > RANGE > T/FINISH.
8) Select the finishing point for the limited tilt (000~255).
9) Go to MENU > RANGE > USE.
10) Select YES to activate the new settings or NO to stop using them.
It is possible to select how you can reset the fixture, whether with the DMX controller or
only from the control panel.
Reset Control
1) Go to MENU > SPECIAL > RESET.
2) Select DMX or SYSTEM.
DMX: Enables the DMX controller to reset the fixture (Control function).
SYSTEM:
Restricts the reset function to the control panel..
Continues on the next page
Q-Wash 360Z-LED User Manual Rev. 01g
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
This option allows you to activate or deactivate the move-in black 3-seconds delay.
1) Go to MENU > SPECIAL > BLACK
Move-in Black
2) Select YES to enable the 3 seconds delay or NO to make the blackout immediate.
You may use this function to boost the output power for specific, short-term applications.
1) Go to MENU > SPECIAL > POWER.
Power
2) Select NORMAL or HIGH.
The fixture will return to Normal if the LEDs’ temperature becomes too high.
The COLOR setting determines how the Q-Wash 360Z-LED generates the white color
based on various RGB settings.
Color Settings
1) Go to MENU > SPECIAL > COLOR.
2) Select OFF, RGBTOW, or UC.
UC:
RGBTOW:
OFF:
When the RGB faders are all set to “255”, the output matches that of less
efficient fixtures (Universal Color).
When the RGB faders are all set to “255”, the resulting output is defined by
RGB-W (see MENU > EXTRA > CALIB).
When the RGB faders are all set to “255”, the output is maximum, although
the resulting white color may not be balanced.
This option defines how you can control the fan speed, whether with the DMX controller or
only from the control panel.
Fan Control
1) Go to MENU > SPECIAL > FAN.
2) Select DMX or SYSTEM.
DMX: Enables the DMX controller to control the fan speed (Control function).
SYSTEM:
Restricts the control of the fan speed to the control panel..
If necessary, you may adjust the color temperature of each of the macros (White1~11).
1) Go to MENU > EXTRA.
Color Calibration
2) Press <ENTER> (PASSWORD) will show on the display.
3) Press <ENTER> (**** will show on the display).
4) Enter the password, as explained in Keylock (CALIB will show on the display).
5) Press <ENTER> (3200K will show on the display).
6) Use <UP> or <DOWN> to select another color temperature (3400~10000 K), or press
<ENTER> to edit the current temperature.
7) Select RED, GREEN, or BLUE.
8) Select a value (000~255).
9) Repeat for the other colors.
Continues on the next page
-12-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
You may calibrate the white color shown when the RGB faders are at “255” and the
MENU > SPECIAL > COLOR setting is RGBTOW.
White Calibration
1) Go to MENU > EXTRA.
2) Press <ENTER> (PASSWORD) will show on the display.
3) Press <ENTER> (**** will show on the display).
4) Enter the password, as explained in Keylock (CALIB will show on the display).
5) Press <ENTER> (3200K will show on the display).
6) Use <UP> or <DOWN> to select RGBW.
7) Select RED, GREEN, or BLUE.
8) Select a value (000~255).
9) Repeat for the other colors.
To default all the fixture’s parameters to their default values, do the following:
1) Go to MENU > EXTRA.
System Default
2) Press <ENTER> (PASSWORD) will show on the display.
3) Press <ENTER> (**** will show on the display).
4) Enter the password, as explained in Keylock (CALIB will show on the display).
5) Use <UP> to select DEFAULT.
6) Press <ENTER> (NO will show on the display).
7) Select YES and press <ENTER> to default the fixture or press <MENU> to exit.
This function allows you to program up to 255 steps in a single custom program.
1) Go to MENU > EDIT.
Edit Custom
2) Press <ENTER> to go to STEP.
3) Press <ENTER> to select a value. The current value (001~255) will show on the LCD.
4) Press <UP> or <DOWN> to select a new value.
5) Press <ENTER> to accept the value.
6) Press <ENTER> to go to PAN.
7) Repeat steps “1” through “6” for TILT, SPEED, RED, GREEN, BLUE, WHITE,
DIMMER, STROBE, ZOOM, DIMSPEED, and TIME.
8) Press <ENTER> to go to USE.
9) Select YES to save the settings for this step or NO to delete them.
10) Repeat steps “3” to “8” for the other steps.
The fixture will execute all the steps in the CUSTOM program and it will stop.
To make the fixture start over add a last step whose duration is 0 seconds.
Example:
Step 1:
Step 2:
Step 3:
Step 4:
Step 5:
Time = 5
Time = 4
Time = 6
Time = 0
Time = 0
Use = Yes
Use = Yes
Use = Yes
Use = Yes
Use = No
(This step creates a loop)
(Unused steps)
Step 255
Time = 0
Use = No
Q-Wash 360Z-LED User Manual Rev. 01g
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Menu Map
1st Level
2nd Level
3rd Level
Description
Selects a starting DMX address
Resets the fixture’s custom settings
ADDRESS
RESET
001~512
NO/YES
HIGH
Select the fan’s operation mode.
NORMAL
LOW
AUTO
NOTE: The fan will go to High mode if the fixture’s internal
temperature becomes too high, despite any manual or
DMX setting
FAN
DMX512
AUTO 1
AUTO 2
CUSTOM
SLAVE
TEST
Selects DMX running mode
Selects the first automatic program
Selects the second automatic program
Selects the user customizable program
Selects the Slave running mode
Starts the fixture’s test sequence
Selects the 11-channel DMX mode
RUN
INTRO
BASIC
CHANNELS
ADVANCED Selects the 15-channel DMX mode
60 CLOSE Turns off the display after 60 seconds
BRIGHT
NO/YES
DIMMER4~1 Slow (DIMMER4) to fast (DIMMER1) dimmer curves
DIMMER0 Linear dimmer
DISPLAY
KEYLOCK
DIMMER
Keeps the display on
Activates/deactivates the control panel password
INFO
PAN
TILT
DIMMER
USE
EDITION
Shows the version of the installed S/W
Defines the direction of the pan fader
Defines the direction of the tilt fader
Defines the direction of the dimmer fader
Activates the changes
NORMAL/
REVERSE
INVERT
RANGE
NO/YES
P/START
P/FINISH
T/START
T/FINISH
USE
Sets the pan start point (restricted range)
Sets the pan end point (restricted range)
Sets the tilt start point (restricted range)
Sets the tilt end point (restricted range)
Activates the changes
000~255
BLACKD
NO/YES
DMX
SYSTEM
Activates the move-in black delay (3 s)
The DMX controller can reset the fixture
The control panel can reset the fixture
RESET
LEDs illuminate at normal or high intensity
NOTE: The fixture will return to Normal if the LEDs’
temperature becomes too high
NORMAL/
HIGH
POWER
SPECIAL
UC
RGBW = 255: The output matches that of older fixtures
COLOR
FAN
RGBTOW RGBW = 255: The RGBW output is set by RGB-W
OFF
DMX
SYSTEM
RGBW = 255: The RGBW output is maximum
The DMX controller can set the fan speed
The control panel can reset the fan speed
Selects the program step
STEP
PAN
Selects the pan position
TILT
Selects the tilt position
SPEED
RED
Selects the pan/tilt speed
EDIT
000~255
GREEN
BLUE
WHITE
Combines red, green, blue, and white to obtain a custom
color
Continues on the next page
-14-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Continued from previous page
1st Level
2nd Level
3rd Level
Description
Selects the dimmer value
Selects the strobe frequency and mode
Select the zoom position
DIMMER
STROBE
ZOOM
000~255
EDIT
(Cont.)
DIMSPEED
TIME
Selects the dimmer speed
Selects the step duration
USE
PASSWORD
NO/YES
****
Activates the changes
Opens the Extra menu (see below)
EXTRA
Extra Menu
1st Level
2nd Level
3rd Level
4th Level
Description
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
RED
GREEN
BLUE
NO/YES
3200 K
Sets color temperature for White 1
Sets color temperature for White 2
Sets color temperature for White 3
Sets color temperature for White 4
Sets color temperature for White 5
Sets color temperature for White 6
Sets color temperature for White 7
Sets color temperature for White 8
Sets color temperature for White 9
Sets color temperature for White 10
Sets color temperature for White 11
3400 K
4200 K
4900 K
5600 K
5900 K
6500 K
7200 K
8000 K
8500 K
10000 K
CALIB
000~255
Sets color temperature for
SPECIAL > COLOR > RGBTOW
RGB-W
DEFAULT
DEFAULT
N/A
Defaults the fixture to factory settings
Q-Wash 360Z-LED User Manual Rev. 01g
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
DMX Values
Channel
Function
Value
Percent/Setting
BASIC
1
2
3
4
5
6
Pan
Tilt
Red
Green
Blue
White
000 ó 255 0~540º
000 ó 255 0~270º
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 005 No function
006 ó 010 High power
011 ó 030 R: 100% G: Up
031 ó 050 R: Down G: 100%
B: 0%
B: 0%
051 ó 070 R: 0%
071 ó 090 R: 0%
091 ó 110 R: Up
G: 100%
G: Down
G: 0%
B: Up
B: 100%
B: 100%
B: Down
B: Up
B: 100%
B: 100%
111 ó 130 R: 100% G: 0%
131 ó 150 R: 100% G: Up
151 ó 170 R: Down G: Down
171 ó 200 R: 100% G: 100%
201 ó 205 White 1: 3200 K
206 ó 210 White 2: 3400 K
211 ó 215 White 3: 4200 K
216 ó 220 White 4: 4900 K
221 ó 225 White 5: 5600 K
226 ó 230 White 6: 5900 K
231 ó 235 White 7: 6500 K
236 ó 240 White 8: 7200 K
241 ó 245 White 9: 8000 K
246 ó 250 White 10: 8500 K
251 ó 255 White 11: 10,000 K
Power and Color
Macro
W: 100%
7
8
9
Dimmer
Strobe
Zoom
000 ó 255 0~100%
000 ó 009 No function
010 ó 255 01~20 Hz
10
000 ó 255 9º~26º
000 ó 019 No function
020 ó 039 Pan/tilt black activation
040 ó 059 Pan/tilt black deactivation
060 ó 079 Automatic fan speed
080 ó 099 Slow fan speed
100 ó 119 Normal fan speed
120 ó 139 High fan speed
11
Control
140 ó 149 Auto program 1 (3 s activation delay)
150 ó 159 Auto program 2 (3 s activation delay)
160 ó 169 Test (3 s activation delay)
170 ó 179 Custom program (3 s activation delay)
180 ó 199 No function
200 ó 219 Reset (3 s activation delay)
220 ó 255 No function
-16-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Channel
Function
Value
Percent/Setting
ADVANCED
1
2
3
4
5
6
7
8
9
Pan
000 ó 255 0~540º
000 ó 255 Fine movement control
000 ó 255 0~270º
Pan Fine
Tilt
Tilt Fine
Pan/Tilt Speed
Red
000 ó 255 Fine movement control
000 ó 255 Fast~Slow
000 ó 255 0~100%
000 ó 255 0~100%
000 ó 255 0~100%
Green
Blue
White
000 ó 255 0~100%
000 ó 005 No function
006 ó 010 High power
011 ó 030 R: 100% G: Up
031 ó 050 R: Down G: 100%
B: 0%
B: 0%
051 ó 070 R: 0%
071 ó 090 R: 0%
091 ó 110 R: Up
G: 100%
G: Down
G: 0%
B: Up
B: 100%
B: 100%
B: Down
B: Up
B: 100%
B: 100%
111 ó 130 R: 100% G: 0%
131 ó 150 R: 100% G: Up
151 ó 170 R: Down G: Down
171 ó 200 R: 100% G: 100%
201 ó 205 White 1: 3200 K
206 ó 210 White 2: 3400 K
211 ó 215 White 3: 4200 K
216 ó 220 White 4: 4900 K
221 ó 225 White 5: 5600 K
226 ó 230 White 6: 5900 K
231 ó 235 White 7: 6500 K
236 ó 240 White 8: 7200 K
241 ó 245 White 9: 8000 K
246 ó 250 White 10: 8500 K
251 ó 255 White 11: 10,000 K
Power and Color
Macro
W: 100%
10
11
12
13
Dimmer
Strobe
Zoom
000 ó 255 0~100%
000 ó 009 No function
010 ó 255 01~20 Hz
000 ó 255 9º~26º
000 ó 009 Set dimmer speed from control panel
010 ó 029 Linear dimmer
030 ó 069 Non-linear dimmer (fastest)
070 ó 128 Non-linear dimmer
14
Dimmer Speed
130 ó 189 Non-linear dimmer
190 ó 255 Non-linear dimmer (slowest)
000 ó 019 No function
020 ó 039 Pan/tilt black activation
040 ó 059 Pan/tilt black deactivation
060 ó 079 Automatic fan speed
080 ó 099 Slow fan speed
100 ó 119 Normal fan speed
120 ó 139 High fan speed
15
Control
140 ó 149 Auto program 1 (3 s activation delay)
150 ó 159 Auto program 2 (3 s activation delay)
160 ó 169 Test (3 s activation delay)
170 ó 179 Custom program (3 s activation delay)
180 ó 199 No function
200 ó 219 Reset (3 s activation delay)
220 ó 255 No function
Q-Wash 360Z-LED User Manual Rev. 01g
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
5. Technical Information
To maintain optimum performance and minimize wear, the user should clean this product
frequently. Usage and environment are contributing factors in determining the cleaning
frequency.
Fixture
Maintenance
As a rule, the user should clean this product at least twice a month. Dust build up reduces
light output performance and can cause overheating. This can lead to reduced light
source life and increased mechanical wear.
To clean a fixture, follow the recommendations below:
·
·
·
Unplug the fixture from power.
Wait until the fixture is cold.
Use a vacuum (or dry compressed air) and a soft brush to remove dust collected on
the external vents and accessible internal components.
·
Clean the LEDs cover with a mild solution of non-ammonia glass cleaner or isopropyl
alcohol.
·
·
·
Apply the solution directly to a soft, lint-free cotton cloth or a lens cleaning tissue.
Drag any dirt or grime to the outside rim of the LEDs cover.
Gently polish the LEDs cover until it is free of haze and lint.
Always dry the LEDs cover carefully after cleaning it.
Refrain from spinning this product’s fans using compressed air.
-18-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
Troubleshooting Guide
Symptom
Cause(s)
Fixture defaulted
Action(s)
Configure fixture’s parameters
Faulty LED board
Fixture is on
LEDs are off
Faulty LED Driver board
Faulty LED Control board
Faulty Display board
Faulty head fan
Send unit for repair
Replace head fan
Fixture and LEDs are on
Head fan is off
Faulty sensor or wiring
Faulty wiring
Verify temperature sensor and wiring
Verify wiring
Faulty zoom servo
Faulty LED Control board
Faulty Display board
Faulty sensor
Fixture and LEDs are on
Zoom is inactive
Send unit for repair
Replace sensor
Faulty pan belt
Replace pan belt
Pan movement problem
Tilt movement problem
Faulty pan motor
Replace pan motor
Faulty Display board
Faulty tilt sensor
Send unit for repair
Replace tilt sensor
Faulty tilt belt
Replace tilt belt
Faulty tilt motor
Replace tilt motor
Faulty Display board
Excessive circuit load
Short circuit along the power wires
No power
Send unit for repair
Reduce total load placed on the electrical circuit
Check electrical wiring
Check for voltage on outlet
Check power cord
Circuit breaker/fuse
keeps tripping/blowing
Loose or damaged power cord
Blown fuse
Fixture does not power
up
Replace fuse
Faulty internal power supply
Wrong DMX addressing
Damaged DMX cables
Wrong polarity on the controller
Loose DMX cables
Non DMX cables
Send unit for repair
Check unit addressing
Check DMX cables
Check polarity switch settings on the controller
Check cable connections
Use only DMX compatible cables
Install terminator as suggested
Bouncing signals
Fixture does not respond
to wired DMX or
responds erratically
Long cable / low level signal
Install an optically coupled DMX splitter before a
long section of cable or right after the fixture with
the strong signal
Too many fixtures
Install an optically coupled DMX splitter after unit
#32
Interference from AC wires
Faulty Display board
Keep DMX cables separated from power cables
or fluorescent/black lights
Send unit for repair
If you still experience technical problems after trying the above solutions or if you
need to send the unit for repair, contact CHAUVET® Technical Support.
Q-Wash 360Z-LED User Manual Rev. 01g
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
The user must send the merchandise prepaid, in the original box, and with its original
packing and accessories. CHAUVET® will not issue call tags.
Returns
Procedure
Call CHAUVET® and request a Return Merchandise Authorization (RMA) number before
shipping the fixture. Be prepared to provide the model number, serial number, and a brief
description of the cause for the return.
The user must clearly label the package with a Return Merchandise Authorization (RMA)
number. CHAUVET® will refuse any product returned without an RMA number.
DO NOT write the RMA number directly on the box. Instead, write it on a properly
affixed label.
Once you have received the RMA number please include the following information on a
piece of paper inside the box:
·
·
·
·
·
Your name
Your address
Your phone number
The RMA number
A brief description of the problem
Be sure to pack the fixture properly. Any shipping damage resulting from inadequate
packaging will be the customer’s responsibility. As a suggestion, proper UPS packing or
double-boxing is always a safe method to use.
CHAUVET® reserves the right to use its own discretion to repair or replace returned
product(s).
The carrier is responsible for any damage incurred during shipping to this product or any
part that shipped with it. Therefore, if the received merchandise appears to have damages
caused during shipping, the customer must submit the damage report and any related
claims with the carrier, not CHAUVET®. The customer must submit the report upon
reception of the damaged merchandise. Failure to do so in a timely manner may invalidate
the customer’s claim with the carrier.
Claims
For other issues such as missing components or parts, damage not related to shipping, or
concealed damage, the customer must make claims to CHAUVET® within seven (7) days
of receiving the merchandise.
World Headquarters
United Kingdom & Ireland
Contact Us
CHAUVET®
CHAUVET® Europe Ltd.
General Information
General Information
Address:
5200 NW 108th Avenue
Sunrise, FL 33351
(954) 929-1115
Address:
Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice:
Fax:
(954) 929-5560
Toll free:
(800) 762-1084
Voice:
Fax:
+44 (0)1773 511115
+44 (0)1773 511110
Technical Support
Technical Support
Voice:
Fax:
Email:
(954) 929-1115 (Press 4)
(954) 756-8015
Email:
World Wide Web
World Wide Web
-20-
Q-Wash 360Z-LED User Manual Rev. 01g
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
Technical Specifications
Length
Width
Height
Weight
Dimensions and
Weight
13.3 in (339 mm)
9.1 in (232 mm)
17.3 in (439 mm)
24.2lbs (11kg)
Note: Dimensions in inches rounded to the nearest decimal digit.
Power Supply Type
Range
Voltage Selection
Electrical
Switching (internal)
100~240 V, 50/60 Hz
Auto-ranging
Parameter
Consumption
120 V, 60 Hz
310 W
230 V, 50 Hz
310 W
Operation/Inrush current
Fuse
2.6 A/2.6 A
T 5 A, 250 V
1.3 A/1.3 A
T 5 A, 250 V
Power I/O
US/Worldwide
IEC
Europe
IEC
Power input connector
Power cord plug
Edison (US)
Local plug
Type
Power
Lifespan
Light Source
LED (91)
3 W
50,000 hours
Color
Red
Quantity
Current
800 mA
800 mA
800 mA
800 mA
23
23
23
22
Green
Blue
White
Parameter
Illuminance @ 5 m
Beam angle
9º~26º Zoom
6,171 lx (9º Zoom)
9º~26º
Photo Optic
Field angle
14º~40º
Pan
Tilt
Motion
Thermal
DMX
0~540º
0~270º
Max. External Temperature
Cooling System
104° F (40° C)
Forced (fans)
I/O Connectors
Connector Type
Channel Range
3- and 5- pin XLR
Sockets
11,15
Product Name
Item Code
Item Number
Ordering
Q-Wash 360Z-LED
01010253
QWASH360ZLED
Q-Wash 360Z-LED User Manual Rev. 01g
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Information
CHAUVET®
5200 NW 108th Avenue
Sunrise, FL 33351 (USA)
(800) 762-1084 – (954) 929-1115
FAX (954) 929-5560
Q-Wash 360Z-LED User Manual Rev. 01g
June 2011
Download from Www.Somanuals.com. All Manuals Search And Download.
|