2H253-25R
SmartSwitch 2200
Installation User’s Guide
FAST ETHERNET WORKGROUP SWITCH
LED
14
13
16
15
18
17
20
19
22
21
24
23
2
1
4
3
6
5
8
7
10
9
12
11
MODE
RX-TX
DPX-SPD
PWR
CPU
RESET
2H253-25R
COM
9034006
Download from Www.Somanuals.com. All Manuals Search And Download.
Only qualified personnel should perform installation procedures.
NOTICE
Cabletron Systems reserves the right to make changes in specifications and other information contained in this document
without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes
have been made.
The hardware, firmware, or software described in this manual is subject to change without notice.
IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL,
OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS)
ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF
CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY
OF SUCH DAMAGES.
2000 by Cabletron Systems, Inc., P.O. Box 5005, Rochester, NH 03866-5005
All Rights Reserved
Printed in the United States of America
Order Number: 9034006 January 2000
Cabletron Systems, LANVIEW, QuickSET, and SecureFast are registered trademarks and SmartSwitch is a trademark
of Cabletron Systems, Inc.
All other product names mentioned in this manual may be trademarks or registered trademarks of their respective
companies.
i
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment uses, generates, and can radiate radio frequency
energy and if not installed in accordance with the operator’s manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause interference in which case the user
will be required to correct the interference at his own expense.
WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
INDUSTRY CANADA NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the
Radio Interference Regulations of the Canadian Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils
numériques de la class A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des
Communications du Canada.
VCCI NOTICE
This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information
Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When
such trouble occurs, the user may be required to take corrective actions.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLETRON SYSTEMS, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE FOLLOWING
GEOGRAPHICAL REGIONS:
CANADA
MEXICO
CENTRAL AMERICA
SOUTH AMERICA
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ
THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) between You, the end user, and Cabletron Systems, Inc. (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in the package.
The Program may be contained in firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU
ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO CABLETRON OR
YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL
REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS
+1- 603-332-9400. Attn: Legal Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the
terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the
United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state
and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by
agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of
certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government
or an exception from obtaining such license may be relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export
Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the
Program for civil end uses only and not for military purposes.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export
Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You
agree not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country
in Country Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia,
Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be
designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct
product of the Program or the technology, if such foreign produced direct product is subject to national security controls
as identified on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r
any major component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as identified on the
U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely
at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section
52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in
all respects is proprietary data belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product
is considered commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and use,
duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron
makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY
CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO
THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS
SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE
ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLETRON SYSTEMS SALES AND SERVICE, INC.
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR USE OF PRODUCT IN THE UNITED STATES OF AMERICA
AND BY UNITED STATES OF AMERICA GOVERNMENT END USERS.
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ
THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) betweenYou, the end user, and Cabletron Systems Sales and Service, Inc.
(“Cabletron”) that sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in
the package. The Program may be contained in firmware, chips or other media. UTILIZING THE ENCLOSED
PRODUCT, YOU ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH
INCLUDES THE LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF
YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO
CABLETRON OR YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT
FOR A FULL REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS
+1- 603-332-9400. Attn: Legal Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the
terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the
United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be interpreted and governed under the laws and in the state
and federal courts of New Hampshire. You accept the personal jurisdiction and venue of the New Hampshire courts.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by
agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of
certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government
or an exception from obtaining such license may be relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export
Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the
Program for civil end uses only and not for military purposes.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export
Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You
agree not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country
in Country Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia,
Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be
designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct
product of the Program or the technology, if such foreign produced direct product is subject to national security controls
as identified on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r
any major component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as identified on the
U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely
at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section
52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in
all respects is proprietary data belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product
is considered commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and use,
duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron
makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY
CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO
THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS
SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE
ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
CABLETRON SYSTEMS LIMITED
PROGRAM LICENSE AGREEMENT
IMPORTANT: THIS LICENSE APPLIES FOR THE USE OF THE PRODUCT IN THE FOLLOWING
GEOGRAPHICAL REGIONS:
EUROPE
MIDDLE EAST
AFRICA
ASIA
AUSTRALIA
PACIFIC RIM
BEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT, CAREFULLY READ
THIS LICENSE AGREEMENT.
This document is an agreement (“Agreement”) betweenYou, the end user, and Cabletron Systems Limited (“Cabletron”)
that sets forth your rights and obligations with respect to the Cabletron software program (“Program”) in the package.
The Program may be contained in firmware, chips or other media. UTILIZING THE ENCLOSED PRODUCT, YOU
ARE AGREEING TO BECOME BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE
LICENSE AND THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT
AGREE TO THE TERMS OF THIS AGREEMENT, RETURN THE UNOPENED PRODUCT TO CABLETRON OR
YOUR DEALER, IF ANY, WITHIN TEN (10) DAYS FOLLOWING THE DATE OF RECEIPT FOR A FULL
REFUND.
IF YOU HAVE ANY QUESTIONS ABOUT THIS AGREEMENT, CONTACT CABLETRON SYSTEMS
+1- 603-332-9400. Attn: Legal Department.
1. LICENSE. You have the right to use only the one (1) copy of the Program provided in this package subject to the
terms and conditions of this License Agreement.
You may not copy, reproduce or transmit any part of the Program except as permitted by the Copyright Act of the
United States or as authorized in writing by Cabletron.
2. OTHER RESTRICTIONS. You may not reverse engineer, decompile, or disassemble the Program.
3. APPLICABLE LAW. This License Agreement shall be governed in accordance with English law. The English
courts shall have exclusive jurisdiction in the event of any disputes.
4. EXPORT REQUIREMENTS. You understand that Cabletron and its Affiliates are subject to regulation by
agencies of the U.S. Government, including the U.S. Department of Commerce, which prohibit export or diversion of
certain technical products to certain countries, unless a license to export the product is obtained from the U.S. Government
or an exception from obtaining such license may be relied upon by the exporting party.
If the Program is exported from the United States pursuant to the License Exception CIV under the U.S. Export
Administration Regulations, You agree that You are a civil end user of the Program and agree that You will use the
Program for civil end uses only and not for military purposes.
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
If the Program is exported from the United States pursuant to the License Exception TSR under the U.S. Export
Administration Regulations, in addition to the restriction on transfer set forth in Sections 1 or 2 of this Agreement, You
agree not to (i) reexport or release the Program, the source code for the Program or technology to a national of a country
in Country Groups D:1 or E:2 (Albania, Armenia, Azerbaijan, Belarus, Bulgaria, Cambodia, Cuba, Estonia, Georgia,
Iraq, Kazakhstan, Kyrgyzstan, Laos, Latvia, Libya, Lithuania, Moldova, North Korea, the People’s Republic of China,
Romania, Russia, Rwanda, Tajikistan, Turkmenistan, Ukraine, Uzbekistan, Vietnam, or such other countries as may be
designated by the United States Government), (ii) export to Country Groups D:1 or E:2 (as defined herein) the direct
product of the Program or the technology, if such foreign produced direct product is subject to national security controls
as identified on the U.S. Commerce Control List, or (iii) if the direct product of the technology is a complete plant o r
any major component of a plant, export to Country Groups D:1 or E:2 the direct product of the plant or a major
component thereof, if such foreign produced direct product is subject to national security controls as identified on the
U.S. Commerce Control List or is subject to State Department controls under the U.S. Munitions List.
5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely
at private expense; (ii) contains “restricted computer software” submitted with restricted rights in accordance with section
52.227-19 (a) through (d) of the Commercial Computer Software-Restricted Rights Clause and its successors, and (iii) in
all respects is proprietary data belonging to Cabletron and/or its suppliers. For Department of Defense units, the Product
is considered commercial computer software in accordance with DFARS section 227.7202-3 and its successors, and use,
duplication, or disclosure by the Government is subject to restrictions set forth herein.
6. EXCLUSION OF WARRANTY. Except as may be specifically provided by Cabletron in writing, Cabletron
makes no warranty, expressed or implied, concerning the Program (including its documentation and media).
CABLETRON DISCLAIMS ALL WARRANTIES, OTHER THAN THOSE SUPPLIED TO YOU BY
CABLETRON IN WRITING, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH RESPECT TO
THE PROGRAM, THE ACCOMPANYING WRITTEN MATERIALS, AND ANY ACCOMPANYING HARDWARE.
7. NO LIABILITY FOR CONSEQUENTIAL DAMAGES. IN NO EVENT SHALL CABLETRON OR ITS
SUPPLIERS BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF BUSINESS, PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS
INFORMATION, SPECIAL, INCIDENTAL, CONSEQUENTIAL, OR RELIANCE DAMAGES, OR OTHER LOSS)
ARISING OUT OF THE USE OR INABILITY TO USE THIS CABLETRON PRODUCT, EVEN IF CABLETRON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE SOME STATES DO NOT
ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES, OR IN THE DURATION OR LIMITATION OF IMPLIED WARRANTIES IN SOME INSTANCES, THE
ABOVE LIMITATION AND EXCLUSIONS MAY NOT APPLY TO YOU.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARATION OF CONFORMITY
Application of Council Directive(s): 89/336/EEC
73/23/EEC
Manufacturer’s Name: Cabletron Systems, Inc.
Manufacturer’s Address: 35 Industrial Way
PO Box 5005
Rochester, NH 03867
European Representative Name: Mr. J. Solari
European Representative Address: Cabletron Systems Limited
Nexus House, Newbury Business Park
London Road, Newbury
Berkshire RG14 2PZ, England
Conformance to Directive(s)/Product Standards: EC Directive 89/336/EEC
EC Directive 73/23/EEC
EN 55022
EN 50082-1
EN 60950
Equipment Type/Environment: Networking Equipment, for use in a Commercial
or Light Industrial Environment.
We the undersigned, hereby declare, under our sole responsibility, that the equipment packaged with this
notice conforms to the above directives.
Manufacturer
Legal Representative in Europe
Mr. Ronald Fotino
Mr. J. Solari
___________________________________
___________________________________
Full Name
Full Name
Compliance Engineering Manager
Managing Director - E.M.E.A.
___________________________________
___________________________________
Title
Title
Rochester, NH, USA
Newbury, Berkshire, England
___________________________________
___________________________________
Location
Location
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
x
Download from Www.Somanuals.com. All Manuals Search And Download.
Figures ..........................................................................................................................................xiii
ABOUT THIS GUIDE
Structure of This Guide ..................................................................................................xv
Document Conventions................................................................................................xvii
1
Overview .........................................................................................................1-1
Connectivity ....................................................................................1-2
Switching Options ...........................................................................1-6
Optional HSIMs and VHSIMs..........................................................1-7
Year 2000 Compliant ......................................................................1-7
1.1.9
1.1.14
1.1.15
1.1.17
Getting Help ....................................................................................................1-8
2
NETWORK REQUIREMENTS
2.1
2.2
2.3
SmartTrunk .....................................................................................................2-1
10BASE-T Network.........................................................................................2-1
100BASE-TX Network.....................................................................................2-2
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
3
3.3
Unpacking the Device .....................................................................................3-1
Installing Options.............................................................................................3-2
Installing the Device........................................................................................3-2
3.3.1
Tabletop or Shelf Installation ..........................................................3-3
Connecting to the Network..............................................................................3-8
Completing the Installation............................................................................3-10
4
Using LANVIEW..............................................................................................4-1
Troubleshooting Checklist...............................................................................4-5
Using the RESET Button.................................................................................4-8
A
A.2
A.3
A.6
Device Specifications......................................................................................A-1
Physical Properties .........................................................................................A-1
Electrical Specifications ..................................................................................A-2
Input/Output Ports...........................................................................................A-2
COM Port Pinout Assignments .......................................................................A-3
B
B.2
B.3
Removing the Chassis Cover..........................................................................B-2
Setting the Mode Switches..............................................................................B-5
SIMM Upgrade................................................................................................B-6
B.4.1
B.4.2
Locating SIMMs ..............................................................................B-7
Installing the DRAM SIMM..............................................................B-7
B.5
INDEX
xii
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure
1-1
3-1
3-2
3-3
3-4
3-5
3-6
4-1
4-2
B-1
B-2
B-3
B-4
B-5
The 2H253-25R SmartSwitch 2200.................................................................................1-1
Tabletop or Shelf Installation...........................................................................................3-4
Attaching the Strain-Relief Bracket .................................................................................3-5
Attaching the Rackmount Brackets .................................................................................3-6
Installing the Device in a Rack ........................................................................................3-6
2H253-25R Rear View ....................................................................................................3-7
Straight Cable Connection ..............................................................................................3-9
LANVIEW LEDs ..............................................................................................................4-1
RESET Button.................................................................................................................4-8
Removing the Chassis Cover..........................................................................................B-4
Mode Switch Location .....................................................................................................B-5
SIMM Slot Locations .......................................................................................................B-7
Installing the DRAM.........................................................................................................B-8
HSIM and VHSIM Connector Locations..........................................................................B-9
xiii
Download from Www.Somanuals.com. All Manuals Search And Download.
Tables
Table
Page
3-1
4-1
4-2
A-1
Contents of 2H253-25R Carton........................................................................................3-2
LANVIEW LEDs ..............................................................................................................4-2
Troubleshooting Checklist ...............................................................................................4-5
COM Port Pin Assignments............................................................................................ A-3
xiv
Download from Www.Somanuals.com. All Manuals Search And Download.
About This Guide
Welcome to the 2H253-25R SmartSwitch 2200 Installation User’s Guide. This guide describes
the 2H253-25R SmartSwitch 2200 device and provides information concerning network
requirements, installation, and troubleshooting. For information about how to use Local
Management to configure and manage the 2H253-25R, refer to the Cabletron Systems
SmartSwitch Series 2E253, 2H252, 2H253 and 2H258 Local Management User’s Guide.
Important Notice
Depending on the firmware version used in the 2H253-25R, some features described in this
document may not be supported. Refer to the Release Notes shipped with the 2H253-25R to
determine which features are supported.
USING THIS GUIDE
Read through this guide and the SmartSwitch Series 2E253, 2H252, 2H253 and 2H258 Local
Management User’s Guide to completely understand the 2H253-25R capabilities and Local
Management functions.
A general working knowledge of Ethernet and IEEE 802.3 type data communications networks
and their physical layer components is helpful when using this device.
In this document, the device is referred to as either the “2H253-25R” or the “device”.
NOTE
This guide is organized as follows:
obtaining additional information or help from Cabletron Systems are also included in this chapter.
Chapter 2, Network Requirements, explains the network requirements to consider before
installing the 2H253-25R.
Chapter 3, Installation, provides instructions on how to install the 2H253-25R and connect
segments to the device.
xv
Download from Www.Somanuals.com. All Manuals Search And Download.
quickly diagnose network/operational problems.
Appendix A, Specifications, contains information on functionality and operating specifications,
connector pinouts, environmental requirements, and physical properties.
Appendix B, Optional Installations and Mode Switch Bank Settings, describes how to remove
the cover from the device, set the Mode Switch, and shows the location of an optional High Speed
Interface Module (HSIM) or Very High Speed Interface Module (VHSIM) when one is installed.
RELATED DOCUMENTS
The following Cabletron Systems documents may help to set up, control, and manage the
2H253-25R:
The following Cabletron Systems documents may help to set up and manage the 2H253-25R:
•
•
•
•
•
SmartSwitch Series 2E253, 2H252, 2H253 and 2H258 Local Management User’s Guide
Ethernet Technology Guide
Cabling Guide
SmartTrunk User’s Guide
WAN Series Local Management User’s Guide
The following are Cabletron Systems documents associated with optional interface modules:
•
•
•
•
•
•
•
•
•
HSIM-A6DP User’s Guide
HSIM-F6 User’s Guide
HSIM-FE6 User’s Guide
HSIM-W6 Installation Guide
HSIM-W84 Installation Guide
HSIM-W87 User’s Guide
HSIM-G01/G09 User’s Guide
VHSIM-G6 User’s Guide
VHSIM-A6DP User’s Guide
xvi
Download from Www.Somanuals.com. All Manuals Search And Download.
Document Conventions
The HSIM-W6 Installation Guide, the HSIM-W84 Installation Guide, and the WAN Series Local
Management User’s Guide are included on the QuickSET CD-ROM and, along with the other
manuals listed above, can be obtained from the World Wide Web in Adobe Acrobat Portable
Document Format (PDF) at the following site:
All documentation for the Cabletron Systems SecureFast VLAN Manager software is
contained on the VLAN Manager CD-ROM.
NOTE
DOCUMENT CONVENTIONS
The guide uses the following conventions:
Note symbol. Calls the reader’s attention to any item of information that may be of
special importance.
NOTE
Tip symbol. Conveys helpful hints concerning procedures or actions.
TIP
Caution symbol. Contains information essential to avoid damage to the equipment.
!
CAUTION
Electrical Hazard Warning symbol. Warns against an action that could result in
personal injury or death due to an electrical hazard.
Warning symbol. Warns against an action that could result in personal injury or death.
WARNING
xvii
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
This chapter introduces the 2H253-25R SmartSwitch 2200 device and provides information about
how to obtain additional support from Cabletron Systems.
Important Notice
Depending on the firmware version used in the 2H253-25R, some features described in this
document may not be supported. Refer to the Release Notes shipped with the 2H253-25R to
determine which features are supported.
1.1 OVERVIEW
The 2H253-25R (Figure 1-1) is an Ethernet/Fast Ethernet standalone device with two RJ21 front
panel connectors (each containing 12 switched ports), and 1 slot for an optional High Speed
Interface Module (HSIM) or Very High Speed Interface Module (VHSIM).
Port Status
LEDs
HSIM/VHSIM Slot
LED MODE Switch
FAST ETHERNET WORKGROUP SWITCH
LED
14
13
16
15
18
17
20
19
22
21
24
23
2
4
3
6
5
8
7
10
9
12
11
MODE
1
RX-TX
DPX-SPD
PWR
RESET
CPU
2H253-25R
COM
Reset
Button
COM
Port
System Network Ports 1-24
LEDs
(Two RJ21 connectors)
27621-01
Figure 1-1 The 2H253-25R SmartSwitch 2200
Introduction
1-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
The 2H253-25R is used to connect individual high-bandwidth user devices, such as workstations,
or to provide a central switching point for multiple 10/100 Mbps Fast Ethernet segments. The
optional HSIMs provide high speed uplinks to networking technologies such as Fast Ethernet,
Gigabit Ethernet, Fiber Distributed Data Interface (FDDI), Wide Area Network (WAN), and
Asynchronous Transfer Mode (ATM). Some HSIMs can provide additional Fast Ethernet ports in
varying media types. The optional VHSIMs provide very high speed uplinks to networking
technologies such as Gigabit Ethernet and ATM.
The 2H253-25R ports can be configured to control frame traffic in several ways, including
prioritizing traffic flow according to protocol type. The 2H253-25R can also be configured to
establish Virtual Local Area Networks (VLANs) and control the flow of frames associated with
each VLAN according to priority and Ether type. Detailed information about VLANs is provided
in the Cabletron Systems 802.1Q VLAN User’s Guide.
The 2H253-25R may be used as a tabletop unit or can be installed in a standard 19-inch rack using
the supplied rack mounting hardware.
The 2H253-25R has two power supplies. The power supplies load share 50% (+/-5%) of the power
required by the device. If one power supply fails, the remaining power supply assumes the entire
load of the device without interruption to network traffic. Each power supply module supports its
own ac input connection, which enables each power supply to be connected to a different ac power
circuit.
1.1.1 Connectivity
The 2H253-25R connects to Ethernet networks or workstations through two RJ21 ports on the
front panel. Each RJ21 connector contains 12, 10/100 Mbps Ethernet ports. These ports are IEEE
802.3 10BASE-T and IEEE 802.3u 100BASE-TX compliant, and they support Category 3
(10-Mbps operation only) and Category 5 Unshielded Twisted Pair cabling. The Category 5
cabling must have an impedance of between 85 and 111 ohms at lengths up to 100 meters.
The device also has a slot for an optional HSIM or VHSIM to provide additional connectivity to
various networking technologies.
1.1.2 Auto-Negotiation
The fixed twisted pair ports (1 through 24) on the 2H253-25R have the ability to auto-negotiate the
type of connection required to provide a link to another device. During Auto-Negotiation, two
devices automatically exchange information so they know each others operating capabilities. The
Auto-Negotiation feature targets the maximum capabilities that can be reached between the two
devices. For example, the 2H253-25R can adjust to 100 Mbps when the device on the other end of
the connection can also adjust from 10 Mbps to 100 Mbps. If the device on the other end of the
connection can only operate at 10 Mbps, then the 2H253-25R simply adjusts to operate at
10 Mbps.
1-2
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
When Auto-Negotiation is supported at both ends of a link, the two devices dynamically adjust to
full or half duplex operation based on the maximum capability that can be reached between the
two devices. If the device connected to the 2H253-25R cannot auto-negotiate, the 2H253-25R
operates according to the capabilities of the other device.
1.1.3 Runtime IP Address Discovery
This feature enables the 2H253-25R device to automatically accept an IP address from a Boot
Strap Protocol (BootP) server on the network without requiring a user to enter an IP address
through Local Management.
When the device is connected to the network and powered up, Runtime IP Address Discovery
(RAD) checks the device for an IP address. If one has not yet been assigned (device IP address set
to 0.0.0.0), RAD checks to see if any of the device interfaces have a link. If so, RAD sends out
Reverse Address Resolution Protocol (RARP) and BootP requests to obtain an IP address from a
BootP server on the network.
The RAD requests start at an interval of 1 per second. The interval then doubles after every
transmission until an interval of 300 seconds is reached. At this point, the interval remains at 300
seconds. The RAD requests continue until an IP address is received from a RARP or BootP server,
or an IP address is entered using Local Management.
The 2H253-25R will reboot after RAD is successful.
NOTE
1.1.4 Full Duplex Switched Ethernet
Each switched Fast Ethernet port on the 2H253-25R supports 10/100 Mbps operation, and can
operate in Full Duplex Switched Ethernet (FDSE) mode. FDSE enables each port to provide up to
200 Mbps of bandwidth to connected devices that support FDSE.
1.1.5 SmartTrunk
Traditional 802.1D Spanning Tree Bridges only allow one active data path between any two
switches; all other parallel data paths are in Standby or Blocking mode. If one interface or path
should fail, then the other interface automatically comes out of Blocking mode and forwards all of
the traffic. This is fine for redundancy purposes. However, it is not the most efficient use of
resources.
Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
SmartTrunk, also referred to as SmartTrunking, is Cabletron Systems’ terminology for load
balancing or load sharing. SmartTrunk provides the ability to take full advantage of the network’s
redundant bandwidth. SmartTrunk divides network traffic across multiple ports in parallel to
provide additional throughput. The SmartTrunk application can be used with any of Cabletron
Systems’ switch modules (except ATM modules).
For more information about SmartTrunk and how to configure it the SmartSwitch device, refer to
the Cabletron Systems SmartTrunk User’s Guide.
1.1.6 Remote Monitoring (RMON)
The 2H253-25R supports all nine Ethernet RMON groups. The Statistics, Alarms, Events and
History groups are enabled on all ports by default.
Cabletron Systems RMON Actions is a vendor-specific extension of RMON and provides the
ability to set an “Action” on any SNMP MIB variable. The Action can be triggered by any RMON
Event and/or Alarm. An example of an Action would be to turn off a MIB-2 interface if a broadcast
threshold is crossed.
1.1.7 Broadcast Suppression
Broadcast Suppression enables a user to set a desired limit of receive broadcast frames per port/per
second to be forwarded out the other ports on the device. Any broadcast frames above this
specified limit are dropped. In the event that broadcast frames are being suppressed, multicast and
unicast frames continue to be switched.
1.1.8 Port/VLAN Redirect Functions
The port redirect function, also referred to as “Port Mirroring,” is a troubleshooting tool used to
map traffic from a single source port to a single destination port within the device. This feature
allows frames, including those with errors to be copied and sent to an analyzer or RMON probe.
The analyzer or RMON probe will see the data as if it were directly connected to the LAN segment
of the source port.
The VLAN redirect function is similar to the port redirect function except that the frames received
by the device are redirected to a designated destination port according to the VLAN classification
of the frames received. Multiple VLANs can be directed to the same port. The VLAN redirect
function is only supported when the device is operating as an 802.1Q switch.
1-4
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1.1.9 Rate Limiting
The Rate Limiting feature enables the SmartSwitch device to control traffic rates on a per-port,
per-priority basis. The network administrator can configure a rate limit (from 100 kbps to 1 Gbs)
for a given port with an associated list of IEEE 802.1p priorities (which can include one, some, or
all of the eight priority levels defined in 802.1p). Each rate limit is specified as an inbound or an
outbound limit. The combined rate of all traffic on the port that matches the listed priorities cannot
exceed the programmed limit. If the rate exceeds the defined limit, frames are dropped until the
rate falls below the limit.
Administrators can configure up to four rate limit rules per port; however, each rule must not
include conflicting 802.1p priority values. In order to control traffic inbound and outbound on the
same port, two rate limit rules must be configured (one inbound and one outbound). Since the rate
limiting operation occurs after the processing of the multi-layer classification rules, the two
features can be combined to provide application-aware rate limiting.
This traffic rate function is not supported on ports configured as SmartTrunk ports.
NOTE
For more information about the application of the Traffic Rate function, refer to the SmartSwitch
Series 2E253, 2H252, 2H253 and 2H258 Local Management User’s Guide.
1.1.10 Flow Control
Flow control is a method of managing the flow of frames between two devices. It ensures that a
transmitting device does not overwhelm a receiving device with data. This is accomplished by the
transmitting device pausing its transmission while the receiving device processes the frames
already received.
The 2H253-25R supports the following two types of flow control:
•
•
Frame based 802.3x
Back pressure
Frame based 802.3x flow control is supported on all Ethernet ports operating in the full duplex
mode. Flow control can be enabled or disabled on a port-by-port basis.
Back pressure flow control is supported on all Ethernet ports operating in the standard mode of
operation. Flow control can be enabled or disabled on a port-by-port basis.
Introduction
1-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1.1.11 GARP Switch Operation
Some or all ports on the switch may be activated to operate under the Generic Attribute
Registration Protocol (GARP) applications, GARP VLAN Registration Protocol (GVRP) and/or
GARP Multicast Registration Protocol (GMRP).
GARP is a protocol, or set of rules, that outlines a mechanism for propagating the port state and/or
user information throughout a bridged LAN to keep track of users and VLANs on the network
fabric. MAC bridges and end users alike can take part in the registration and de-registration of
GARP attributes such as VLAN and multicast group membership. For more details on how GVRP
and GMRP handle frames under GARP, and how to configure the switch ports to take advantage of
this operation, refer to the SmartSwitch Series 2E253, 2H252, 2H253 and 2H258 Local
Management User’s Guide.
1.1.12 802.1 Port Priority
The 802.1 port priority is used to assign a default priority to the frames received without priority
information in their tag header, map prioritized frames to the appropriate transmit queues, and
prioritize frames according to protocol type. The 802.1 port priority is part of the IEEE 802.1D
standard.
1.1.13 Management
Management of the 2H253-25R is accomplished using SNMP-compliant management tools for
in-band Local Management. Out-of-band Local Management is provided through the RJ45 COM
port on the front panel using a VT100 terminal or a VT100 terminal emulator. In-band remote
management is possible through any SNMP compliant Network Management Software.
Local Management described in the SmartSwitch Series 2E253, 2H252, 2H253 and 2H258 Local
Management User’s Guide provides the ability to manage the 2H253-25R, and optional HSIMs
and VHSIMs that support Ethernet. For information about Local Management for optional
non-Ethernet HSIMs or VHSIMs, refer to their respective user’s guide.
1.1.14 Switching Options
The 2H253-25R provides 802.1Q switching or SecureFast Switching Virtual Network Services
between all of the front panel interfaces including the optional HSIM or VHSIM interface. In the
802.1Q mode (the default mode of operation), the switch functions as an 802.1D switch until
VLANs are configured.
IEEE 802.1Q switching and SecureFast switching allow migration to Virtual Network
technologies without requiring the replacement of existing equipment.
1-6
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
1.1.15 Optional HSIMs and VHSIMs
Optional HSIMs and VHSIMs are available from Cabletron Systems for additional connectivity to
various networking technologies. The HSIMs and VHSIMs available for the 2H253-25R are listed
in the Release Notes shipped with the device.
1.1.16 Standards Compatibility
The 2H253-25R is fully compliant with the IEEE 802.3, 802.3u, 802.3x, 802.1D, and 802.1Q
standards. The 2H253-25R provides IEEE 802.1D Spanning Tree Algorithm (STA) support to
enhance the overall reliability of the network and protect against “loop” conditions. The
2H253-25R supports a wide variety of industry standard MIBs including RFC 1213 (MIB II),
RFC 1757 (RMON), RFC 1493 (Bridge MIB), RFC 1354 (FIB MIB), and RFC 1190 (Path MTU
Discovery). A full suite of Cabletron Systems Enterprise MIBs provide a wide array of statistical
information to enhance troubleshooting. For information on how to extract and compile individual
MIBs, contact Cabletron Systems.
1.1.17 Year 2000 Compliant
The 2H253-25R has an internal clock that can maintain the current time and date beyond the year
1999.
1.1.18 LANVIEW Diagnostic LEDs
LANVIEW diagnostic LEDs serve as an important troubleshooting aid by providing an easy way
to observe the status of individual ports and overall network operations.
Introduction
1-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Help
1.2 GETTING HELP
For additional support related to this device or document, contact Cabletron Systems using one of
the following methods:
World Wide Web
Phone
(603) 332-9400
Internet mail
FTP
anonymous
Login
Password
your email address
To send comments or suggestions concerning this document, contact the Cabletron Systems
Make sure to include the document Part Number in the email message.
Before calling Cabletron Systems, have the following information ready:
•
•
•
Your Cabletron Systems service contract number
A description of the failure
A description of any action(s) already taken to resolve the problem (e.g., changing mode
switches, rebooting the unit, etc.)
•
•
•
•
•
The serial and revision numbers of all involved Cabletron Systems products in the network
A description of your network environment (layout, cable type, etc.)
Network load and frame size at the time of trouble (if known)
The device history (i.e., have you returned the device before, is this a recurring problem, etc.)
Any previous Return Material Authorization (RMA) numbers
1-8
Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Network Requirements
Before installing the 2H253-25R, review the requirements and specifications referred to in this
chapter concerning the following:
•
•
•
SmartTrunk (Section 2.1)
10BASE-T Twisted Pair Network (Section 2.2)
100BASE-TX Twisted Pair Network (Section 2.3)
The network installation must meet the requirements to ensure satisfactory performance of this
equipment. Failure to do so will produce poor network performance.
The Cabletron Systems SmartTrunk User’s Guide and Cabling Guide referred to
in the following sections can be found on the Cabletron Systems World Wide
NOTE
Web site: http://www.cabletron.com/
2.1 SmartTrunk
To connect the 2H253-25R to a network so it can take advantage of the SmartTrunk feature, there
are certain rules concerning port connections and configurations that must be followed for proper
operation. Refer to the Cabletron Systems SmartTrunk User’s Guide for additional information.
2.2 10BASE-T NETWORK
When connecting a 10BASE-T segment to any of the 2H253-25R ports (1 through 24), ensure that
The ports support Category 3 UTP cabling when connected to a 10BASE-T segment. Refer to the
Cabletron Systems Cabling Guide for details.
If a port is to operate at 10 and 100 Mbps, Category 5 cabling must be used.
Refer to Section 2.3 for information about 100BASE-TX networks and cabling.
NOTE
Network Requirements
2-1
Download from Www.Somanuals.com. All Manuals Search And Download.
100BASE-TX Network
2.3 100BASE-TX NETWORK
The two RJ21 connectors on the front panel of the 2H253-25R each provide 12 fixed ports (ports 1
through 24) that support Category 5 UTP cabling. The device at the other end of the twisted pair
segment must meet IEEE 802.3u 100BASE-TX Fast Ethernet network requirements for the
devices to operate at 100 Mbps. Refer to the Cabletron Systems Cabling Guide for details.
The fixed ports of the 2H253-25R support Category 5 UTP cabling that has an
impedance between 85 and 111 ohms.
NOTE
The 2H253-25R is capable of operating at either 10 or 100 Mbps.When the port
is configured for Auto-Negotiation, the 2H253-25R automatically senses the
speed of the other device and adjusts its speed accordingly.
2-2
Network Requirements
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Installation
Only qualified personnel should install the 2H253-25R.
Read the Release Notes shipped with the device to check for any exceptions to the
supported features and operation documented in this guide.
NOTE
required to install options into the device or install the device into a rack. Follow the order of the
sections listed below to correctly install the device.
•
•
•
•
•
Unpacking the Device (Section 3.1)
Installing Options (Section 3.2)
Installing the Device (on a shelf or tabletop, or into a standard rack) (Section 3.3)
Connecting to the Network (Section 3.4)
Completing the Installation (Section 3.5)
3.1 UNPACKING THE DEVICE
Unpack the device as follows:
1. Open the box and remove the packing material protecting the 2H253-25R.
2. Verify the contents of the carton as listed in Table 3-1.
Installation
3-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Options
Table 3-1 Contents of 2H253-25R Carton
Item
Quantity
2H253-25R
1
1
1
1
1
1
Antistatic Wrist Strap
Console Cable Kit
Rackmount Kit
Strain-Relief Bracket
Manual Accessory Kit
Power Cord
3. Remove the tape seal on the non-conductive bag to remove the 2H253-25R.
Systems if there are any signs of damage. Refer to Section 1.2 for details.
3.2 INSTALLING OPTIONS
Install any optional equipment before proceeding to Section 3.3.
NOTE
If the 2H253-25R is to be installed with an optional HSIM or VHSIM, refer to the user’s guide of
that device for the installation instructions.
3.3 INSTALLING THE DEVICE
The 2H253-25R may be installed on a tabletop, shelf, or in a 19-inch rack. Section 3.3.1 describes
a tabletop or shelf installation and Section 3.3.2 describes the rackmount installation.
To prevent possible personal injury and/or damage to the unit, do NOT connect power to
the 2H253-25R until instructed to do so.
3-2
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Device
3.3.1 Tabletop or Shelf Installation
The following two subsections provide guidelines for installation on a tabletop or shelf.
Guidelines for Tabletop and Shelf Installations
Tabletop and shelf installations must be within reach of the network cabling and meet the
requirements listed below:
•
•
•
Locate the 2H253-25R within seven feet of an appropriately grounded power receptacle that
meets the power supply requirements listed in Appendix A.
In a shelf installation, the shelf must support 13.5 kg (30 lb) of static weight for each
2H253-25R.
Maintain a temperature of between 5°C (41°F) and 40°C (104°F) at the installation site with
fluctuations of less than 10°C (18°F) per hour.
To ensure proper ventilation and prevent overheating, leave a minimum clearance space
of 5.1 cm (2.0 in) at the left, right, and rear of the 2H253-25R.
!
CAUTION
•
Maintain a 2-inch clearance from the left, right, and rear sides of the device to provide adequate
ventilation.
Installation
For a tabletop or shelf installation, locate the 2H253-25R within seven feet of its power source and
on an unrestricted free surface area as shown in Figure 3-1. Proceed to Section 3.3.3 for power
connection instructions.
Installation
3-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Device
C
B
FAST ETHERNET WORKGROUP SWITCH
LED
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
20
19
22
21
24
23
MODE
RX-TX
DPX-SPD
PWR
CPU
A
RESET
2H253-25R
COM
D
A = 15 cm (6 in)
B = 57 cm (22.5 in)
C = 53 cm (21 in)
D = 213 cm (7 ft)
2762-02
Figure 3-1 Tabletop or Shelf Installation
3.3.2 Rackmount Installation
To install the 2H253-25R in a 19-inch rack, Cabletron Systems includes a strain-relief bracket for
cable management and an accessory kit containing the rackmount brackets, and mounting screws
to attach the rackmount brackets and strain-relief bracket.
Guidelines for the Rackmount Installation
The installation site must be within reach of the network cabling and meet the requirements listed
below:
•
•
An appropriate grounded power receptacle must be located within seven feet of the location.
Maintain a temperature of between 5°C (41°F) and 40°C (104°F) at the installation site with
fluctuations of less than 10°C (18°F) per hour.
To ensure proper ventilation and prevent overheating, leave a minimum clearance space
of 5.1 cm (2.0 in) at the left, right, and rear of the 2H253-25R.
!
CAUTION
Before installing the 2H253-25R into a rack, ensure that the rack supports the device(s)
without compromising the stability of the rack. Otherwise, personal injury and/or
equipment damage may result.
WARNING
3-4
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Device
Installation
Rack mounting the 2H253-25R involves the following:
•
•
Attaching the strain-relief bracket
Rack mounting the 2H253-25R (attaching the mounting brackets and fastening the device to the
rack)
Attaching the Strain-Relief Bracket
Attach the strain-relief bracket to the 2H253-25R as follows:
Do not attempt to attach the strain-relief bracket with screws other than the 8-32 x
5/16-inch screws included with the 2H253-25R. Use of longer screws may damage the
!
CAUTION
unit.
2. Place the 2H253-25R upside down (as shown in Figure 3-2) on a clean flat surface. Then attach
the strain-relief bracket to the bottom of the 2H253-25R using the four 8-32 x 5/16-inch
pan-head screws.
Strain-Relief
Bracket Screws
Strain-Relief
Bracket
C O M
2 H 2 5 3 - 2 5 R
C P U
P W R
R E S E T
D P X - S P D
R X - T X
2 3
2 4
2 1
2 2
1 9
2 0
1 7
1 8
1 5
1 6
1 3
1 4
1 1
1 2
9
7
8
5
6
3
4
1
2
M O D E
L E D
1 0
S W I T C H
A F S T E T H E R N E T W O R K G R O U P
2762-03
Figure 3-2 Attaching the Strain-Relief Bracket
Installation
3-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Device
Rack Mounting the 2H253-25R
Proceed as follows to install the 2H253-25R into a 19-inch rack:
that each mounting bracket may be adjusted forward or backward to mount the device further
into, or out of the rack, depending on the installation requirements. Position the rackmount
brackets over the appropriate holes.
2. Locate the four 6-32 x 1/4-inch flathead screws in the rackmount kit. Use these screws to attach
the rackmount brackets to the bottom of the 2H253-25R as shown in Figure 3-3.
Rackmount Bracket Screws
Rackmount Bracket
C O M
2 H 2 5 3 - 2 5 R
P W R
D P X - S P D
R X - T X
2 3
2 4
2 1
2 2
1 9
2 0
1 7
1 8
1 5
1 6
1 3
1 4
1 1
1 2
9
7
8
5
6
3
4
1
2
M O D E
L E D
1 0
S W I T C H
A F S T E T H E R N E T W O R K G R O U P
27621-04
Figure 3-3 Attaching the Rackmount Brackets
3. With the mounting brackets attached, position the 2H253-25R between the vertical frame
members of the 19-inch rack and fasten it securely with mounting screws as shown in
Figure 3-4.
FAST ETHERNET WORKGROUP SWITCH
2
1
4
3
6
5
8
7
10
9
12
11
14
13
16
15
18
17
20
19
22
21
24
23
-
Screws
19-Inch Rack
27621-05
Figure 3-4 Installing the Device in a Rack
3-6
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Device
3.3.3 Connecting Power
The two power supplies in the 2H253-25R have automatic voltage sensing that allows
50/60 Hz.
NOTE
To connect the 2H253-25R to the power sources, proceed as follows:
1. Plug each power cord into a grounded wall outlet, see Figure 3-5. To take advantage of the load
sharing and redundancy capabilities, each power cord must be plugged into a separate dedicated
ac outlet. The POWER LED turns ON (green) and the CPU LED alternates between green and
amber during boot up. It takes approximately one minute for the 2H253-25R to boot up.
If the power-up sequence is interrupted on this device, or if optional hardware has been
installed or removed, this device may run an extended diagnostics sequence that may
NOTE
take up to five minutes to complete.
Primary
Redundant
AC outlets are
on separate circuits
26001-06
Figure 3-5 2H253-25R Rear View
Installation
3-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Network
2. Observe the LANVIEW LEDs. After a successful boot, the PWR LED turns ON (green). If the
PWR LED is amber, there is no power redundancy. Check the power cord connections and the
power source. If there are no problems with the power cord connections or power source and
the PWR LED is still amber, contact Cabletron Systems for support. Refer to Section 1.2 for
details.
3.4 CONNECTING TO THE NETWORK
This section provides the procedures for connecting unshielded twisted pair (UTP) segments from
the network or other devices to the 2H253-25R. To make connections to an optional HSIM or
VHSIM installed in the HSIM/VHSIM slot of the 2H253-25R, refer to the associated user’s guide
for the HSIM or VHSIM.
If the 2H253-25R is being installed in a network using SmartTrunking, there are rules
concerning the network cable and port configurations that must be followed for
NOTE
SmartTrunking to operate properly. Before connecting the cables, refer to the Cabletron
Systems SmartTrunk User’s Guide for the configuration information.
Each of the two RJ21 connectors on the front panel have 12 UTP port connections. These ports (1
through 24) are 10/100 ports with internal crossovers. When connecting a workstation, use a
straight-through cable. When connecting networking devices, such as another bridge, repeater, or
router, use a crossover cable.
If a port is connected to a 10-Mbps segment, Category 3 Unshielded Twisted Pair (UTP)
cable is sufficient to use. However, if the segment is to carry 10- or 100-Mbps
NOTE
transmissions, use only Category 5 UTP cabling that has an impedance of between 85
and 111 ohms.
To connect an RJ21, proceed as follows:
1. Ensure that the device connected to the other end of the segment is powered on.
2. If using an RJ21 straight connector, plug it into the appropriate RJ21 port as shown in
Figure 3-6.
3-8
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting to the Network
Receive (RX)
LED
MODE
LED MODE Switch
in RX–TX position
RX-TX
Transmit (TX)
DPX-SPD
24
22
20
18
17
23
16
15
21
14
13
19
12
10
9
8
6
5
11
4
3
2
1
7
LED
MODE
RX-TX
DPX-SPD
PWR
CPU
RESET
COM
2H253-25R
Screw
RJ21
LED MODE Switch
Screw
2762-07
3. Tighten the two screws on the RJ21 straight cable connector to secure it to the device.
The cable pinouts for a 25-pair cable (RJ21) can be found in the Cabletron Systems
Cabling Guide. Refer to Section 1.2 for details on how to obtain this document.
NOTE
4. Verify that a link exists on each twisted pair segment of the RJ21 connector by checking that
the associated port RX LED is on (flashing amber, blinking green, or solid green). If the RX
LED is off and the TX LED is not blinking amber, perform the following steps until it is on:
a. Verify that the LED switch located near the COM port of the device is in the left-most
position (RX and TX LED indicators) as shown in Figure 3-6.
10BASE-T or 100BASE-TX). The Category 5 cabling must have an impedance of between
85 and 111 ohms.
If a port is to operate at 10 and 100 Mbps, Category 5 cabling must be used. Refer to
Section 2.3 for information about 100BASE-TX networks and cabling.
NOTE
Installation
3-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Completing the Installation
up.
d. Check the cable for continuity.
e. If a link is not established, contact Cabletron Systems for technical support. Refer to
Section 1.2 for details.
5. Repeat steps 1 through 4 above, until all connections have been made.
3.5 COMPLETING THE INSTALLATION
After installing the 2H253-25R and any optional HSIM or VHSIM, and making the connections to
the network, proceed as follows:
1. Secure the cables by running the cables along the strain-relief bracket and tying them to the
strain-relief bracket using cable ties.
2. The 2H253-25R is now ready to be configured through Local Management. Refer to the
SmartSwitch Series 2E253, 2H252, 2H253, and 2H258 Local Management User’s Guide for
information on how to access and use Local Management.
3-10
Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Troubleshooting
This chapter provides information concerning the following:
•
•
•
Using LANVIEW (Section 4.1)
Troubleshooting Checklist (Section 4.2)
Using the RESET Button (Section 4.3)
4.1 USING LANVIEW
The 2H253-25R uses Cabletron Systems’ built-in visual diagnostic and status monitoring system
called LANVIEW. The LANVIEW LEDs (Figure 4-1) allow quick observation of the network
status to aid in diagnosing network problems.
Receive (RX)
Full Duplex Status
Speed Status
LED
LED
MODE
MODE
RX-TX
RX-TX
A
B
DPX-SPD
DPX-SPD
Transmit (TX)
FAST ETHERNET WORKGROUP SWITCH
LED
14
13
16
15
18
17
20
19
22
21
24
23
2
1
4
3
6
5
8
7
10
9
12
11
MODE
RX-TX
DPX-SPD
PWR
RESET
CPU
2H253-25R
COM
CPU
PWR
LED functions when LED MODE switch is in the RX-TX position. This is the
default switch setting.
A
B
LED functions when LED MODE switch is in the DPX-SPD position.
2762-09
Figure 4-1 LANVIEW LEDs
Troubleshooting
4-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Using LANVIEW
The LED MODE switch is located on the front panel of the 2H253-25R as shown in Figure 4-1.
This switch enables the user to change the function of the port LEDs. When the LED MODE
switch is moved to the left, the LEDs indicate the receive (RX) and transmit (TX) status of the
respective fixed ports (ports 1 through 24). When the LED MODE switch is moved to the right, the
port LEDs indicate whether the respective ports are operating in the standard or full duplex mode
(FDX) and if their operating speed (SPD) is 10 or 100 Mbps.
The LED mode switch does not change the function of any LEDs on an installed HSIM
or VHSIM.
NOTE
Table 4-1 describes the LED indications and provides recommended actions as appropriate.
Refer to the HSIM or VHSIM user’s guide for a description of the HSIM or VHSIM LED
indications.
The terms flashing, blinking, and solid used in Table 4-1 indicate the following:
NOTE
Flashing indicates an LED is flashing randomly.
Blinking indicates an LED is flashing at a steady rate (approximately 50% on, 50% off).
Solid indicates a steady LED light. No pulsing.
Table 4-1 LANVIEW LEDs
LED
Color
State
Recommended Action
PWR
Off
Device electronics not
receiving power from power
supply(ies).
1.Ensure that the power cords are
plugged in correctly and that there is
power at the power source.
2.Contact Cabletron Systems for
assistance.
Green
Functional. Power supply(ies)
operating normally.
None.
Amber Indicates loss of power supply
redundancy.
1.Ensure that the power cords are
plugged in correctly and that there is
power at the power source.
2.Contact Cabletron Systems for
assistance.
4-2
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Using LANVIEW
Table 4-1 LANVIEW LEDs (Cont’d)
State Recommended Action
LED
Color
CPU
Off
Power off.
Power up device.
Red
Blinking. Hardware failure has Contact Cabletron Systems for
occurred. assistance.
Solid. Resetting, normal power If the LED remains Red for several
up reset.
minutes, contact Cabletron Systems
for assistance.
Amber Blinking. Crippled.
Solid. Testing.
Contact Cabletron Systems for
assistance.
If the LED remains Amber for several
minutes, contact Cabletron Systems
for assistance.
Green
Solid. Functional.
None.
None.
Amber Booting. Blinks amber and
and
green while booting.
Green
The following port RX and TX LED indications are only valid when the LED MODE switch is
in the RX-TX position.
RX
Off
No link.
None.
None.
(Receive)
Green
Solid. Port enabled, link, no
activity.
Blinking. Port disabled, link.
None.
None.
Amber Flashing. Port enabled, link,
activity.
Red
Diagnostic failure.
Contact Cabletron Systems for
assistance.
Troubleshooting
4-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Using LANVIEW
Table 4-1 LANVIEW LEDs (Cont’d)
State Recommended Action
LED
Color
TX
(Transmit)
Off
Port enabled, and no activity.
1.Ensure that the STA is enabled and
that there is a valid link.
2.Contact Cabletron Systems for
assistance.
Should flash green every two
seconds indicating BPDUs
being sent if STA is enabled
and there is a valid link.
Green
Flashing. Indicates activity.
None.
Rate indicates data rate.
Amber Blinking. Port in standby.
1.Ensure that the port is not disabled.
2.Contact Cabletron Systems for
assistance.
Port may be disabled due to
Spanning Tree.
Red
Flashing. Indicates collision
rate.
None, unless there is a high amount of
activity. In this case, check for
network configuration problems or a
defective device.
Solid. Diagnostic failure.
Contact Cabletron Systems for
assistance.
The following port DPX and SPD LED indications are only valid when the LED MODE switch
is in the DPX-SPD position.
FDX
Amber Port is operating in standard
mode (10 Mbps or 100 Mbps).
None.
(Full
Duplex
Status)
Green
Port is operating in full duplex None.
mode (20 Mbps or 200 Mbps).
SPD
(Speed
Status)
Amber There is a link and the port is
operating at 10 Mbps.
None.
Green
There is a link and the port is
operating at 100 Mbps.
None.
4-4
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
4.2 TROUBLESHOOTING CHECKLIST
If the 2H253-25R is not working properly, refer to Table 4-2 for a checklist of possible problems,
causes, and recommended actions to resolve the problem.
Table 4-2 Troubleshooting Checklist
Problem
Possible Cause
Recommended Action
All LEDs are
OFF.
Loss of power.
Check for proper connection of the
power cable and its access to a live
outlet.
Installed improperly.
Ensure that the 2H253-25R was
installed properly according to the
installation instructions in Chapter 3.
No Local
Management
Autobaud is enabled, but the
baud rate has not yet been
Press ENTER (RETURN) (may take
up to four times).
Password screen. detected.
Terminal setup is not correct.
Refer to the SmartSwitch Series
2E253, 2H252, 2H253, and 2H258
Local Management User’s Guide for
proper setup procedures.
Improper console cable pinouts. Refer to Appendix A for proper
console port pinouts.
Corrupt firmware image, or
hardware fault.
If possible, attempt to download the
image to the 2H253-25R again. Refer
to Section B.3 for instructions to clear
NVRAM.
Cannot navigate
beyond Password Table.
screen.
Improper Community Names
1.Refer to the SmartSwitch Series
Local Management User’s Guide for
the Community Names Table setup.
2.If you have forgotten the
Community Names, refer to
Appendix B for instructions on how
to set the mode switch to reset the
Community Names to their default
values.
Troubleshooting
4-5
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
Table 4-2 Troubleshooting Checklist (Cont’d)
Problem
Possible Cause
Recommended Action
Cannot contact
the 2H253-25R
through in-band
management.
IP address not assigned.
Refer to the SmartSwitch Series
2E253, 2H252, 2H253, and 2H258
Local Management User’s Guide for
IP address assignment procedure.
Port is disabled.
Enable port. Refer to the SmartSwitch
Series 2E253, 2H252, 2H253, and
2H258 Local Management User’s
Guide for instructions to
enable/disable ports.
No link to device.
1.Verify that all network connections
between the network management
station and the 2H253-25R are valid
and operating.
2.If the problem continues, contact
Cabletron Systems for assistance.
Port(s) goes into
standby for no
apparent reason.
Loop condition detected.
1.Verify that Spanning Tree is
enabled. Refer to the SmartSwitch
Series 2E253, 2H252, 2H253, and
2H258 Local Management User’s
Guide for the instructions to set the
type of STA.
2.Review network design and delete
unnecessary loops.
3.If the problem continues, contact
Cabletron Systems for assistance.
4-6
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting Checklist
Table 4-2 Troubleshooting Checklist (Cont’d)
Problem
Possible Cause
Recommended Action
User parameters
(IP address,
Device and
Module name,
etc.) were lost
when the
2H253-25R
power was cycled
or the front panel 2.Clear NVRAM was set
1. Position of Mode switch (7),
NVRAM Reset, was changed
sometimebeforeeithercycling
power or pressing the RESET
button, causing the
user-entered parameters to
reset to factory default
settings.
1.Reenter the lost parameters as
necessary. Refer to the SmartSwitch
Series 2E253, 2H252, 2H253, and
2H258 Local Management User’s
Guide for the instructions to
configure the device through Local
Management.
2.If the problem continues, contact
Cabletron Systems for assistance.
RESET button
was pressed.
through Local Management.
Troubleshooting
4-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the RESET Button
4.3 USING THE RESET BUTTON
The RESET button shown in Figure 4-2 resets and re-initializes the 2H253-25R.
Pressing the RESET button resets the device, and all current switching being performed
by the device is halted. A network downtime of up to two minutes will result from this
!
CAUTION
action.
FAST ETHERNET WORKGROUP SWITCH
LED
14
13
16
15
18
17
20
19
22
21
24
23
2
1
4
3
6
5
8
7
10
9
12
11
MODE
RX-TX
DPX-SPD
PWR
CPU
RESET
2H253-25R
COM
2762-10
RESET Button
Figure 4-2 RESET Button
To reset the 2H253-25R processor, press and release the RESET button. The 2H253-25R goes
through a reset process for approximately 60 seconds. Additional downtime may result as the
device reenters the network.
It is not recommended to press the RESET button while the device is already in reset
mode. If so, the device will enter an extended diagnostic procedure, which is
NOTE
unnecessary for normal operation. This extended diagnostic procedure takes much
longer than a minute.
4-8
Troubleshooting
Download from Www.Somanuals.com. All Manuals Search And Download.
A
Specifications
This appendix provides operating specifications for the Cabletron Systems 2H253-25R. Cabletron
Systems reserves the right to change these specifications at any time without notice.
A.1 DEVICE SPECIFICATIONS
Processors:
Intel i960 RISC processor Power PC
Dynamic Random Access
Memory (DRAM):
20 MB expandable to 32 MB
FLASH Memory:
Shared Memory:
8 MB
4 MB
A.2 PHYSICAL PROPERTIES
Dimensions:
7.11H x 43.18W x 46.99D (cm)
2.8H x 17W x 18.5D (in)
Approximate Weight (Unit):
MTBF (Predicted):
8.18 kg (18 lb)
200,000 hours
Specifications
A-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Specifications
A.3 ELECTRICAL SPECIFICATIONS
Line Input Range, Volts (V):
100–125 Vac
2.3 A
200–240 Vac
1.2 A
Input Current, Amperes (A):
Frequency, Hertz (Hz):
50/60 Hz
250 VA
50/60 Hz
250 VA
Input Power, Volt Amperes (VA:)
A.4 ENVIRONMENTAL REQUIREMENTS
Operating Temperature:
Storage Temperature:
5°C to 40°C (41°F to 104°F)
-30°C to 73°C (-22°F to 164°F)
5% to 90% (non-condensing)
Operating Relative Humidity:
A.5 INPUT/OUTPUT PORTS
Ports 1 through 24:
Fast Ethernet 10/100 Mbps (10BASE-T and
100BASE-TX compliant) with RJ21 type connectors
(twelve ports per connector).
Interface Slot:
Slot accepts optional High Speed Interface Module
(HSIM) or Very High Speed Interface Module
(VHSIM) to provide a variety of cabling
connections.
A-2
Specifications
Download from Www.Somanuals.com. All Manuals Search And Download.
COM Port Pinout Assignments
A.6 COM PORT PINOUT ASSIGNMENTS
The COM port is a serial communications port that supports Local Management or connection to a
UPS.
Table A-1 shows the COM port pin assignments.
Table A-1 COM Port Pin Assignments
Pin
Signal Name
Input/Output
1
2
3
4
5
6
7
8
Transmit Data (XMT)
Data Carrier Detect (DCD)
Data Set Ready (DSR)
Receive Data (RCV)
Output
Output
Input
Input
NA
Signal Ground (GND)
Data Terminal Ready (DTR)
Request to Send (RTS)
Clear to Send (CTS)
Output
Input
NA
A.7 REGULATORY COMPLIANCE
This equipment meets the following safety and electromagnetic compatibility (EMC)
requirements:
Safety:
UL 1950, CSA C22.2 No 950, 73/23/EEC,
EN 60950, IEC 950
Electromagnetic
Compatibility (EMC):
FCC Part 15, CSA C108.8, 89/336/EEC, EN 55022,
EN 61000-3-2, EN 61000-3-3, EN 50082-1,
AS/NZS 3548, VCCI V-3
Specifications
A-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
B
Optional Installations and
Mode Switch Bank Settings
ONLY QUALIFIED SERVICE PERSONNEL SHOULD ATTEMPT THE FOLLOWING
PROCEDURES.
NUR QUALIFIEZIERTE SERVICE PERSONNAL DIE FOLGENDE PROCEDURE
FOLGEN SOLLTEN.
SOLAMENTE PERSONAL CALIFICADO DEBE INTENTAR ESTE PROCEDIMIENTO.
The top cover must be removed to gain access to the mode bank switches, to install optional
Interface Module (HSIM) or Very High Speed Interface Module (VHSIM).
This appendix covers the following items:
•
•
•
•
•
Required tools (Section B.1)
Removing the chassis cover (Section B.2)
Locations, functions, and settings for the mode switches (Section B.3)
Installing optional SIMM upgrades (Section B.4)
Location of optional HSIMs (Section B.5)
B.1 REQUIRED TOOLS
Use the following tools to perform the procedures provided in this appendix:
•
•
Antistatic wrist strap
Phillips screwdriver
Optional Installations and Mode Switch Bank Settings
B-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Chassis Cover
B.2 REMOVING THE CHASSIS COVER
This section describes how to remove the 2H253-25R chassis cover.
DO NOT REMOVE THE COVER FROM THE 2H253-25R WHILE POWER IS APPLIED
TO THE UNIT. HAZARDOUS VOLTAGES ARE PRESENT AND COULD CAUSE
PERSONAL INJURY AND/OR DAMAGE THE UNIT.
DO NOT POWER UP THE 2H253-25R AGAIN UNTIL THE COVER AND SCREWS
ARE IN PLACE.
DECKEL VON DAS 2H253-25R NICHT ABZIEHEN UNTER SPANNUNG. GEFAHR
FÜR DAS PERSONNAL UND/ODER DAS GERÄT WEGEN GEFÄHRLICHE
SPANNUNGEN ENSTEHT.
2H253-25R NICHEINSCHALTEN SO LANG DER DECKEL UND SCHRAUBEN NICHT
EINGEBAUT SIND.
NO DEBE DE REMOVER LA TAPA DURENTE QUE ESTE CONELTADO A LA
CORRIENTE, UNA DESCARGA ELECTRICA LE PUEDE CAUSAR Y PROBOCARLE
DAÑOS, AL IGUAL QUE AL APARATO.
NO ENCHUFE A LA CORRIENTE HASTA QUE LA TAPA Y LOS TORNILLOS ESTEN
EN SU LUGAR.
CAUTION: THIS UNIT MAY HAVE MORE THAN ONE POWER SUPPLY CORD.
DISCONNECT TWO POWER SUPPLY CORDS BEFORE SERVICING TO AVOID
ELECTRIC SHOCK.
VORSICHT: DIESES GERÄT HAT MEHR ALS EINEN NETZANSCHLUß. TRENNEN
SIE VOR WARTUNGSARBEITEN DIE 2 NET ZANSCHLÜSSE VOM NETZ, UM
ELEKTRISCHE SCHLÄGE ZU VERMEIDEN.
ATTENTION: CET APPAREIL COMPORTE PLUS D’UN CORDON D’ALIMENTATION.
RAFIN DE PREVENIR LES CHOCS ELECTRIQUES, DEGRANCHER LES DEUX
CORDONS D’ALIMENTATION AVANT DE FAIRE LE DEPANNAGE.
B-2
Optional Installations and Mode Switch Bank Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Chassis Cover
To remove the chassis cover, proceed as follows:
1. Disconnect the 2H253-25R from the network as follows:
a. Unplug both power cords from the rear of the chassis.
TURN OFF THE 2H253-25R BY UNPLUGGING THE POWER CORD FROM THE
REAR OF THE CHASSIS.
AM HINTEN DES 2H253-25R STECHEI ABZIEHEN UM AUS ZU SCHALTEN.
APAGUE EL 2H253-25R DESENCHUFE EL CABLE DE LA UNIDAD.
Before performing step b, mark the cables connected to the 2H253-25R according to
their associated port numbers. This is recommended for ease of reinstallation.
TIP
2. If the 2H253-25R is rack mounted, remove it from the rack and remove the rackmount brackets
(refer to Chapter 3).
3. Use a Phillips screwdriver to remove the four screws attaching the cover to the chassis. (See
Figure B-1.)
4. Remove the cover by sliding it back until it clears the front of the chassis and then lifting it
straight up and off the chassis.
To reinstall the chassis cover, perform the removal procedures in reverse.
Optional Installations and Mode Switch Bank Settings
B-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Chassis Cover
Screws (4)
Chassis Cover
Front Panel
Chassis
Note: If the device was rack mounted, the four screws fastening the cover to
the front panel are removed and installed along with the rackmount brackets.
2504-30
Figure B-1 Removing the Chassis Cover
B-4
Optional Installations and Mode Switch Bank Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Mode Switches
B.3 SETTING THE MODE SWITCHES
Figure B-2 shows the location of the mode switches and the switch settings for normal operation.
These switches are set at the factory and rarely need to be changed.
Switch definitions and positions are as follows:
•
•
Switches 1 through 4 – For Cabletron Systems use only.
Switch 5 – COM Port Autobaud. The default (OFF) position enables Autobaud sensing on the
COM port for Local Management sessions. Changing the switch to the ON position disables
Autobaud sensing and sets the COM port to 9600 baud for Local Management sessions.
TOP VIEW WITHOUT COVER
Redundant
Power
Supply
Primary
Power
Supply
MODE SWITCH BANK
ON
OFF
1
2
3
4
5
6
7
8
FRONT PANEL
25041-11
Figure B-2 Mode Switch Location
•
Switch 6 – Forced BootP.
After changing the position of switch 6, DO NOT reapply power to the chassis until there
is a station on the network acting as a BootP server, which contains the downloadable
firmware image file.
NOTE
Optional Installations and Mode Switch Bank Settings
B-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SIMM Upgrade
DO NOT attempt a Forced BootP unless a BootP server has been configured for the
2H253-25R. The BootP server references the location of a station acting as a Trivial File
Transfer Protocol (TFTP) server containing the 2H253-25R image file.
When the position of Switch 6 is changed and the power is cycled to the 2H253-25R, the device
requests the image file location from the BootP server and uses TFTP to download the image
from the TFTP server. If one of these requirements is not met, the 2H253-25R continues to
request either the BootP server or the TFTP server until the RESET button on the 2H253-25R
is pressed. Once the RESET button is pressed, the 2H253-25R resets after one minute and loads
the image stored in FLASH memory.
•
•
Switch 7 – Clear NVRAM. Changing the position of this switch resets NVRAM on the next
power-up of the device. All user-entered parameters, such as the IP address, device names, etc.,
are reset to the factory default settings. Once the 2H253-25R resets, you can either use the
factory default settings or reenter your own parameters.
Switch 8 – Reset Password/Community Names. Changing the position of this switch clears
user-entered passwords stored in NVRAM, and restores the factory default passwords on the
next power-up of the device. Once the 2H253-25R resets, you can either use the factory default
settings or reenter your own passwords.
Do not change the position of Switch 8 unless it is necessary to reset the module
super-user configured passwords to their factory default settings.
NOTE
B.4 SIMM UPGRADE
Memory upgrade is available for the 2H253-25R to expand its DRAM to 32 MB. This section
explains how to locate and add/replace a Single In-line Memory Module (SIMM). For information
on the available SIMM upgrades, call Cabletron Systems for technical support. For details on
getting help, refer to Section 1.2.
B-6
Optional Installations and Mode Switch Bank Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
SIMM Upgrade
B.4.1 Locating SIMMs
Figure B-3 shows the two locations of the DRAM SIMM connector.
TOP VIEW WITHOUT COVER
Redundant
Power
Supply
Primary
Power
Supply
DRAM
FRONT PANEL
2504-84
Figure B-3 SIMM Slot Locations
B.4.2 Installing the DRAM SIMM
Observe all antistatic precautions when handling sensitive electronic equipment.
!
CAUTION
To install a DRAM SIMM, refer to Figure B-4 and proceed as follows:
1. With the SIMM alignment notch oriented as shown in Figure B-4, insert the SIMM down
between the connector teeth.
Optional Installations and Mode Switch Bank Settings
B-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SIMM Upgrade
2. Pivot the SIMM downward so the connector clips align with the two side notches of the SIMM
and the connector clips lock the SIMM into place.
Connector
Connector
Teeth
Clip
Side Notch
1
Clip
Alignment Notch
2
SIMM
Side Notch
2504-91
Figure B-4 Installing the DRAM
B-8
Optional Installations and Mode Switch Bank Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Optional HSIM or VHSIM Interface Modules
B.5 INSTALLING OPTIONAL HSIM OR VHSIM INTERFACE MODULES
Figure B-5 shows the location of the two connectors for an optional High HSIM or VHSIM.
Depending on the HSIM or VHSIM installed, one or both connectors are used.
The installation instructions for the optional HSIM or VHSIM are in the associated user’s
guide.
NOTE
TOP VIEW WITHOUT COVER
Redundant
Power
Supply
Primary
Power
Supply
Optional
HSIM or VHSIM
Connectors
FRONT PANEL
Figure B-5 HSIM and VHSIM Connector Locations
2504-31
Optional Installations and Mode Switch Bank Settings
B-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Numerics
D
100BASE-T
requirements 2-2
10BASE-T
requirements 2-1
2H253-25R
Environmental requirements A-2
description of 1-1
front panel 1-1
802.1p Port Priority
introduction to 1-6
F
Flow control
introduction to 1-5
Full Duplex Switched Ethernet, introduction
to 1-3
A
Auto-Negotiation
introduction to 1-2
G
Getting help 1-8
B
Broadcast Suppression
introduction to 1-4
installation of B-9
C
Cable specifications
100BASE-TX network 2-2
10BASE-T network 2-1
Chassis cover, removal of B-2
COM port
High speed interface module
location of B-9
pin assignments A-3
Connecting to the network 3-8
Connectivity
in a rack 3-4
on a tabletop or shelf 3-3
Very High speed interface module
location of B-9
introduction to 1-2
Index-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
L
S
LANVIEW LEDs 4-1
Local Management
introduction to 1-6
SIMMs
location B-7
introduction to 1-3
Specifications A-1
Standards compatibility 1-7
Switching options
introduction to 1-6
M
Management
use of 1-6
Memory
upgrading B-6
Mode Switch
setting B-5
T
Troubleshooting 4-1
checklist 4-5
N
Network connections 3-8
Unpacking 3-1
P
Physical properties A-1
Port Redirect Function, introduction to 1-4
Power connection 3-7
V
VLAN Redirect Function, introduction to 1-4
R
Redirect functions
port and VLAN, introduction to 1-4
Regulatory Compliance A-3
Related manuals xvi
Remote Monitoring (RMON)
introduction to 1-4
RESET button 4-8
Runtime IP address discovery
introduction to 1-3
Index-2
Download from Www.Somanuals.com. All Manuals Search And Download.
|