Have Questions?
Quick Setup Guide
Do not return to store. We can help.
Call Customer Service Toll-Free 1-800-743-4115
or vist our web site BRIGGSandSTRATTON.COM
Portable Generator
Add Engine Oil and Fuel
WARNING Failure to read and follow the operator’s
manual and all operating instructions could
result in death, serious injury, and/or property
damage.
WARNING Running engine gives off carbon
4
monoxide, an odorless, colorless, poison
gas. Breathing carbon monoxide could result
in death, serious injury, nausea or fainting.
Operate this product ONLY outdoors. DO NOT operate
this product inside any building or enclosure, even if
windows and doors are open.
NOTICE Be sure you have attached wheels and support leg prior to this
step.
NOTICE You MUST properly fill engine with oil before attempting to
start generator.
WARNING Fuel and its vapors are extremely
flammable and explosive which could cause
burns, fire or explosion resulting in death,
serious injury and/or property damage. Turn
generator engine OFF and let it cool at least 2 minutes
before removing fuel cap. Let spilled fuel evaporate
before starting engine. Always allow space for fuel
expansion.
NOTICE DO NOT use unapproved fuel such as E85.
NOTICE DO NOT mix oil in fuel.
L
WARNING Generator voltage could cause electrical
shock or burn resulting in death or serious
injury. DO NOT operate under wet conditions.
NOTICE DO NOT modify engine to run on alternate fuels.
1. Move generator outdoors to a flat, level surface.
2. Clean area around oil fill and remove yellow oil fill
5
cap/dipstick ( ).
4
3. Using oil funnel (optional), slowly pour contents of provided oil bottle
WARNING Contact with muffler area could cause
burns resulting in serious injury. DO NOT
into oil fill opening to the point of overflowing (L).
4
4. Replace oil fill cap/dipstick and fully tighten.
touch hot parts and AVOID hot exhaust gases.
5
5. Clean area around fuel fill cap ( ), remove cap.
6. Slowly add unleaded gasoline (M) to fuel tank (N). Be careful not
to fill above the baffle (P). This allows adequate space for fuel
6
7
6
expansion as shown.
T
N
P
7. Install fuel cap and let any spilled fuel evaporate before starting
engine.
F
M
Move Generator to
Safe Operating Location
Exhaust Port
Pointed away from
dwelling openings
Items Included:
8
9
Operator’s Manual (Not Shown)
1. Move generator outdoors to a flat, level surface, in an area that will
not accumulate deadly exhaust gas. DO NOT place generator where
exhaust gas could accumulate and enter inside or be drawn into a
potentially occupied building. Ensure exhaust gas is kept away from
any windows, doors, ventilation intakes, or other openings that can
allow exhaust gas to collect in a confined area. Prevailing winds and
acurrents should be taken into considration when positioning
Q
7
generator.
o reduce the risk of exhaust xhaust gases igniting nearby
mbustible material, keep at 1.5 m) clearance on all
es of generator, including ov
R
Start Generator
1. Make sure unit s on a level surface. Disconnect all electrical loads
from the generaor.
8
2. Turn the fuel alve (Q) to the “On” position.
You Will Need:
9
3. Move choke levr (R) to “Choke” position.
• Utility knife • Socket wrench with 13 mm socket • 13 mm wrench • Unleaded fue• Oil Funnel (Optional)
4. engine rocker switch (S) to “ON or I” position.
10
10
5. coil handle and pull slowly until slight resistance is felt. Then
idly one time only to start engine.
U
Unpack Generator
1
If engine starts, proceed to step 7. If engine does not start, refer to
operator’s manual for detailed starting instructions.
1. Set the carton on a rigid flat surface.
S
B
2. Remove everything from carton except generator.
3. Open carton completely by cutting each corner from top to bottom.
7. Slowly move choke lever to “Run” position. If engine falters, move
choke lever to “Half” choke position until engine runs smoothly, and
then to “Run” position.
T
4. Ensure you have all included items prior to assembly. If items are
damaged or missing call 1-800-743-4115.
Plug in Items to be Powered
5. Leave generator on carton to install wheel kit.
1. Let engine stabilize and warm up for a few minutes after starting.
NOTICE DO NOT connect 240 Volt loads to the 120 Volt receptacles.
NOTICE DO NOT connect 3-phase loads to the generator.
NOTICE DO NOT connect 50 Hz loads to the generator.
C
Install Wheel Kit
A
NOTICE Wheels and support leg must be attached prior to adding any
fuel and oil.
2
3
1. Tip generator so that engine end is down.
NOTICE DO NOT OVERLOAD THE GENERATOR. See Don’t Overload
Generator, in Operator’s Manual.
G
2. Slide axle stud (A) through wheel (B).
1
NOTICE Be sure to install wheel with raised hub inboard.
3. Slide a spacer (C) over axle stud on back side of wheel.
WARNING Damaged or overloaded electrical cords could overheat,
arc, and burn resulting in death, serious injury, and/or
property damage. ONLY use cords rated for your loads.
1
4. Slide axle stud through mounting bracket.
1
Follow all safeties on electrical cords. Inspect cord sets before
each use.
5. Insert retaining pin (D) through hole on axle stud.
1
F
E
6. Repeat steps 2 through 5 to secure second wheel.
2. Connect electrical loads in OFF position, then turn ON for operation.
3. Plug in and turn on the desired 120 Volt AC (T), single phase, 60 Hz
7. Line up holes in support leg (E) with holes in generator frame.
2
electrical loads.
10
8. Attach support leg using two 16 mm capscrews (F) and two M8 hex
nuts (G). Tighten with a 13 mm socket wrench and 13 mm wrench.
2
4. Push-to-reset circuit breakers (U) are provided to protect the
K
J
generator against electrical overload.
10
9. Return generator to normal operating position (resting on wheels).
H
10. Slide handle bracket over generator frame and attach handle (H)
using two 50 mm capscrews (J) and two M8 hex nuts (K). Tighten
Shut Down Generator
with a 13 mm socket wrench and 13 mm wrench.
3
1. Turn OFF and unplug all electrical loads from generator panel
receptacles. NEVER start or stop engine with electrical devices
plugged in and turned on.
2. Let engine run at no load for several minutes to stabilize internal
temperatures of engine and generator.
10
3. Push rocker switch (S) to “OFF or O” position.
8
4. Move fuel valve (Q) to “Off” position.
5. To prepare for storage, refer to Storage in Operator’s Manual.
© 2012 Briggs & Stratton Power Products Group, LLC. All rights reserved.
Every effort has been made to ensure that the information in this document is accurate and correct. However, we reserve the right to alter or otherwise improve the product and this document at any time without prior notice and without incurring obligation.
This generator is rated in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-04 (motors and generators).
316674, Rev A
Download from Www.Somanuals.com. All Manuals Search And Download.
|