Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Power Requirements
Power Consumption
Screen Size
DC 12V
9W
11. 2 TFT-LCD
16:9 Wide
Screen Format
Resolution Pixel
2400*480
A/V Inputs
2 A/V RCA Inputs
(L)13. 5 (W)12. 1 (H)3. 1inch
DC 12V
Dimensions
IR Power Requirements
IR Power Consumption
IR Transmitter Frequency
LCD Panel Type
3W
Right 2. 8MHz Left 2. 3MHz
Active Matrix TFT
NTSC/PAL auto select
Compatible video standard
Note : This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at his own expense.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO OPERATE THE MONITOR
Releasing the Monitor
CONTENTS
Push the open button (located on the front edge of the screen housing)
and lower the monitor to the desired angle. You can also adjust the
swivel angle.
,
Please read this User s Manual in detail and use the set properly.
CAUTION
4
5
INSTALLATION
PUSH BUTTON
NAME AND FUNCTION OF EACH PARTS
Unit
6
6
Remote Control
7
CONNECTIONS
8
HOW TO OPERATION THE MONITOR
Releasing The Monitor
How To Watch Monitor
SPECIFICATIONS
9
9
How to watch the monitor
9
10
1. Connect the monitor to the external devices.
2. Press the POWER button on either the remote control or the unit once to turn
the power on.
Press the same POWER button to turn the power off.
POWER
POWER
REMOTE CONTROLLER
UNIT
3. Turn on the external devices and view.
9
2
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
CONNECTIONS
,
Please read and observe all warnings and instructions in this owner s manual
and those marked on the unit. Retain this booklet for future reference.
There are two kinds of alarm symbols as follows:
Red AUDIO(R)
White AUDIO(L)
Yellow VIDEO
The lightening flash with arrowhead symbol within an equilateral
triangle is intended to alert the user to the presence of
Red AUDIO(R)
GAME
,
dangerous voltage within the product s enclosure that may be
of sufficient magnitude to constitute a risk of electric shock to
GAME
White AUDIO(L)
WARNING
people.
Yellow VIDEO
CAMCORDER
CAMCORDER
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
YELLOW
AV Input
(AV 2)
Constant 12 Volts
AV Input
(AV 1)
BLACK
RED
Ground
the product.
CAUTION
Switched 12 Volts
Car dome lamp
WHITE
WARNING
Do not mount the product where
Installation of all TV monitors
must be out of the driver s
field of sight.
it will obstruct the deployment of
the airbag or in an area where it
would affect the vehicular control.
Also be careful to avoid mounting
the product where it can become
hazardous during sudden stops or
in the event of an accident.
M
E
N
U
Do not try and service these
products yourself, Seek only
a qualified service center or
factory service center.
Use extra caution with any liquids
in your car. If you or your child
Spills any liquid on these products,
pull your vehicle to the roadside
and turn the key off to disconnect
or wipe the products with a towel. Do not
operate the equipment until all liquids have
either evaporated or you have had the monitor
inspected at a service center by a qualified
technician, Severe harm or danger can
Occur.
Be careful not to drop or
apply under pressure to the
front panel of your video
monitor. If the screen cracks
due to misuse, your warranty
will be void!
Use only a damp cloth to clean
the screen and use only purified
water on the cloth. Wring out all
excess water prior to wiping the
screen. Do not use any cleaners
or chemicals to clean the screen.
In most cases a dry cloth will do!
Be careful not to overload your
cigarette lighter plug by adding
more than one device at a time.
Positive Negative
Trigger Door Trigger Door
Switch Switch
Dome Light Trigger
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
NAME AND FUNCTION OF EACH PART
POWER Button
Dome Light Button
MENU Button
CAUTION
Watching the monitor for an
extended period of time
with the engine turned off
may deplete the vehicle s
battery.
Quality installations are best
performed by qualified and
certifled installers.
This product is designed for
operation with a 12 Volt DC,
negative ground vehicle. It
is not suitable for operation
under other conditions or
voltages.
Don t touch the unit if there is
a flash of lightning. It may
receive an electric shock.
Dome Light Button
AV Select Button
+/- Buttons
Do not cover heater ducts or vents.
This may cause a fire or an electric
shock.
Interface Switch Function
Power Power ON/OFF
AV Signal Select
Menu Press this button for OSD menu.
And select menu option
Increase current option value.
Decrease current option value.
+
-
Check Point
1. The operating temperature of this product is limited to 14 F~140 F
(-10 C~60 C).
Your vehicle can reach temperatures up to 100 C in the summertime.
POWER KEY
AV1/AV2 KEY
MENU KEY
2. When your vehicle is extremely hot or cold you must allow time for your air
conditioner or heater to cool or heat the vehicle and for operating temperatures
to return to normal operating ranges. Your monitor will return to its normal
functions when these operating ranges are achieved.
3. Optimum picture quality is achieved when you are directly in front of the monitor
(+/-45 degrees).
+ KEY
- KEY
7
4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
NAME AND FUNCTION OF EACH PART
Unit
1. Open the package and check that these items are presents.
Dome light
INSTALLATION PLATE
UNIT
SCREW A
SCREW B
Infrared Transmitter
2. Connect the external compoments to the RCA cable or AV output.
(Refer to the connection diagram on page 8)
3.Match the position of installation bracket and
installation plate with screw A.
Monitor
(Front)
AUX Input Jack
4. Tighten the unit with the supplied
screw B.
VIDEO
AUDIO
L
AV2 INPUTS
R
Monitor
(Rear)
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|