Operation guide
High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Contents
Preface................................................................................................................................. 5
Notes for the reader......................................................................................................................................... 6
Components and their functions.......................................................................................7
Description of the main parts..........................................................................................................................8
Description of the stacker control panel.......................................................................................................10
Basic instructions..............................................................................................................13
Turn the stacker on.........................................................................................................................................14
Turn the stacker off........................................................................................................................................ 15
Eject a stack manually....................................................................................................................................16
Use the stacker................................................................................................................. 17
Filling scenarios..............................................................................................................................................18
Change the default stacker settings..............................................................................................................19
Set the maximum stack height......................................................................................................................21
Set the minimum filling level........................................................................................................................ 22
Examples of using the Maximum stack height and the Minimum filling level settings...........................23
Troubleshooting................................................................................................................27
Error location labels....................................................................................................................................... 28
Remove an error sheet from the internal error tray (A1)............................................................................30
Clear a paper jam in the input paper path (A2-A5)......................................................................................31
Clear a paper jam in the input paper path of the registration unit (A6-A7)...............................................33
Clear a paper jam in the paper path (B1)......................................................................................................35
Clear a paper jam in the horizontal paper path (B2-B5)..............................................................................37
Clear a paper jam at the flip wheel (C1)....................................................................................................... 39
Options.............................................................................................................................. 41
Use the EasyLift to unload the stacker......................................................................................................... 42
Specifications....................................................................................................................45
Specifications..................................................................................................................................................46
Index...................................................................................................................................47
3
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
4
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes for the reader
Notes for the reader
Introduction
This manual helps you to use the High Capacity Stacker-G1 . The manual contains a description
of the product and guidelines to use and operate the High Capacity Stacker-G1 .
Definition
Attention-Getters
Parts of this manual require your special attention. These parts can provide the following:
• Additional general information, for example, information that is useful when you perform a
task.
• Information to prevent personal injuries or property damage.
Symbols used in this manual
The following symbols are used in this manual to explain procedures, restrictions, handling
precautions, and instructions that should be observed for safety.
Overview of the attention-getters
Word
Icon
Indicates
WARNING
Indicates a warning concerning operations that may
lead to death or injury to persons if not performed
correctly. To use the machine safely, always pay at-
tention to these warnings.
CAUTION
Indicates a caution concerning operations that may
lead to injury to persons if not performed correctly.
To use the machine safely, always pay attention to
these cautions.
IMPORTANT
Indicates operational requirements and restrictions.
Be sure to read these items carefully to operate the
machine correctly and to avoid damaging the ma-
chine or property.
NOTE
Indicates a clarification of an operation or contains
additional explanations for a procedure. Reading
these notes is highly recommended.
-
Indicates an operation that must not be performed.
Read these items carefully and make sure not to
perform the described operations.
6
Chapter 1 - Preface
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the main parts
Description of the main parts
Illustration
10
5
6
4
2
7
1
3
8
9
[1] The main parts of High Capacity Stacker-G1
Main parts
Part
Description
1
2
3
Front door
Front cover
Slide door
The front door gives access to the registration unit and
the error locations A1-A7.
The front cover gives access to the flip rings and error
location C1 (flip wheel).
The slide door covers the tray and the stack inside the
stacker.
4
5
Top cover
The top cover gives access to the error locations B1-B5.
Power switch cover
The optional power switch cover shields the power
switch.
6
7
Power switch
The optional power switch turns the machine on or off.
Stacker control panel
The stacker control panel contains status LEDs, error
LEDs and the eject button.
8
Stack tray
The stack tray receives the prints and transfers the stack
of prints to the eject tray. After the transfer, the stack
tray moves back up and the filling can continue.
4
8
Chapter 2 - Components and their functions
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the main parts
Part
Description
9
Eject tray
The eject tray receives the stack from the stack tray.
Then the eject tray moves horizontally out of the stacker.
When the eject tray is outside the stacker, you can re-
move the stack. In the meantime, the filling of the stack
tray can continue. When you empty the eject tray regu-
larly, the printer can continue printing. This maximizes
the productivity.
10
Top tray
The top tray is an output location for small jobs, proof
prints, error prints and unused cyclic media.
Related information
Chapter 2 - Components and their functions
9
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the stacker control panel
Description of the stacker control panel
Illustration
A
E
D
C
B
[2] The items of the stacker control panel
Description of the stacker control panel
Item
A
Description
Filling level indicator (off, orange or red).
Stack height indicators.
B
C
Eject button.
The eject button LED can have the following statuses:
• Off: Normal situation
• Blinking slowly (green): The stack will be ejected at the next possible set
boundary.
Therefore, the stack will usually contain complete sets.
• Blinking fast (green): The stack will be ejected as soon as possible.
Therefore, the stack can contain incomplete sets.
• Permanent red: An error has occurred that requires opening the slide
door.
D
E
Error location indicators.
Error indicator.
Status LEDs on the stacker control panel
Status LEDs
Status
Description
No stack height indicator is lit. The stack tray is
empty.
When the machine is off or in low power
mode, the LEDs are off.
4
10
Chapter 2 - Components and their functions
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the stacker control panel
Status
Description
1 stack height indicator is lit. The stack tray
contains at least 1 sheet.
All stack height indicators are lit. The stack
height comes close to the factory default value
of 302 mm (11.9").
Stacks with a height of maximum 302 mm
(11.9") are always ejected properly. For higher
stacks, there is a risk that the top sheets touch
the underside of the slide door when ejected.
Error LEDs on the stacker control panel
Error LEDs
Error
Description
Paper tray icon is orange. The stack height ex-
ceeds 302 mm (11.9"). This is possible when
the maximum stack height and the filling level
are set to a higher level than the factory de-
fault value, for example.
Paper tray icon is red. Operator intervention is
required. The eject tray must be emptied be-
fore printing continues.
The green LEDs in the illustration are just an
example. The red icon does not depend on the
number of LEDs lit.
An error or paper jam has occurred at the posi-
tion indicated in red. In this example, the paper
jam has occurred at the flip wheel (C1).
Related information
Chapter 2 - Components and their functions
11
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the stacker control panel
12
Chapter 2 - Components and their functions
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the stacker on
Turn the stacker on
The power switch is optional. If the switch is missing, the high capacity stacker is turned on
automatically when the printer is turned on.
CAUTION
Never plug in the power plug while your hands are wet. Doing so creates the risk of electric
shock.
Illustration
[3] The location of the power switch
Procedure
1. Confirm that the power plug is plugged securely into a power outlet.
2. Open the power switch cover.
3. Press the ON side (I) of the power switch to turn the stacker on.
4. Close the power switch cover.
14
Chapter 3 - Basic instructions
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Turn the stacker off
Turn the stacker off
The power switch is optional. If the switch is missing, the high capacity stacker is turned off
automatically when the printer is turned off.
CAUTION
Never unplug the power plug while your hands are wet. Doing so creates the risk of electric
shock.
Illustration
[4] The location of the power switch
Procedure
1. Open the power switch cover.
2. Press the OFF side (O) of the power switch to turn the stacker off.
3. Close the power switch cover.
4. If required, disconnect the power plug to cut off the power supply to the stacker completely.
Chapter 3 - Basic instructions
15
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Eject a stack manually
Eject a stack manually
Eject a stack
When you press the eject button on the stack‐ Then
er
1x
The stack will be ejected on the next possible
The eject button on the stacker control panel
blinks slowly (green).
set boundary. Then the filling of the stacker
continues.
Therefore, the stack will usually contain com-
plete sets.
2x
The stack will be ejected as soon as possible.
Then the filling of the stacker continues.
Therefore, the stack can contain incomplete
sets.
The eject button on the stacker control panel
blinks fast (green).
NOTE
To stop a job competely, you must use the Stop button on the printer control panel.
16
Chapter 3 - Basic instructions
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Filling scenarios
Filling scenarios
Filling scenarios
Scenario
Description
Where to define the settings?
Filling with default
settings
The stack tray is filled until the
stack reaches the factory default
height of 302 mm (11.9"). Then
the stack is ejected.
Next job, next tray
Each new job is delivered to an On the printer control panel: [Sys-
empty stack tray.
tem] -> [Setup] -> [Workflow profile]
-> [Output] -> [Next output tray] ->
[After each job].
Maximum tray filling
To optimize the productivity,
you can set the stack height to
maximum 355 mm (14.0").
Due to curl and an uneven toner
coverage of sheets, a slanting
stack can occur. This can result
in sheets falling off the stack
during the ejection because
these sheets can touch the un-
derside of the slide door.
In the Settings Editor: [Preferences] -
> [Print job defaults] -> [Stacker] ->
[Maximum stack height].
See the section 'Set the maxi-
mum stack height'.
Limit the stack height According to your needs, if
In the Settings Editor: [Preferences] -
stacks must fit into boxes for ex- > [Print job defaults] -> [Stacker] ->
ample, you can define a stack
height below the factory default
value.
[Maximum stack height].
See the section 'Set the maxi-
mum stack height'.
Filling level
This setting is used to keep sets In the Settings Editor: [Preferences] -
together.
See the section 'Set the mini-
mum filling level'.
> [Print job defaults] -> [Stacker] ->
[Minimum filling level].
18
Chapter 4 - Use the stacker
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Change the default stacker settings
Change the default stacker settings
Introduction
In the Settings Editor on the PRISMAsync controller, a key operator can define a number of
default stacker settings ([Preferences] -> [Print job defaults] - [Stacker]). These settings are
described below. Some of these default settings can be overruled in an application, on the printer
operator panel and in the printer driver.
NOTE
The [Stacker] section also displays settings for other stackers. Only for the High Capacity
Stacker-G1 the settings described below are applicable.
NOTE
Changing these settings requires the key operator password for the Settings Editor.
Settings for the stacker
Setting
Description
[Stacker]
Feed edge
This read-only setting indicates whether a stacker is present.
The feed edge is the direction in which the printed documents are de-
livered to the stack tray, either [Long-edge feed (LEF)] or [Short-edge
feed (SEF)]. You can only select the feed edge for A4-like or LTR-like
media. The feed edge for large media, A3 and Tabloid for example, is
always [Short-edge feed (SEF)]. You can set the feed edge for both the
top tray and the stack tray.
Factory default value: [Long-edge feed (LEF)].
Face orientation
The face orientation defines whether the front side of the printed docu-
ments points up or down. [Face down] means that the front side of the
sheet points down. You can set the face orientation for both the top
tray and the stack tray.
Factory default value: [Face down].
Header orientation
The header orientation defines whether the header of the printed docu-
ments points towards the back or towards the front of the printer.
[Header-up] means that the header points towards the back of the
printer. You can set the header orientation for both the top tray and the
stack tray.
Factory default value: [Header-up].
Reverse order
Offset stacking
The sheet order defines how the sheets are delivered to the tray. [First
sheet first] means that the first sheet is delivered first. You can set the
reverse order for both the top tray and the stack tray.
Factory default value: [First sheet first].
Offset stacking means that each set is shifted on top of the previous set
to create a visible distinction between sets. You can define a value from
0-15 mm (0-0.6") for the stack tray only.
When you set the value to 0 you get the straightest stacks possible.
When the value is 0 while offset stacking is enabled, for example in a
workflow profile, the offset stacking setting will be overruled. The
sheets will be stacked without offset.
Factory default value: 15 mm (0.6").
4
[Minimum filling level] See the section 'Set the minimum filling level'.
Chapter 4 - Use the stacker
19
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Change the default stacker settings
Setting
Description
[Maximum stack
height]
See the section 'Set the maximum stack height'.
Procedure
1. Access the Settings Editor on the PRISMAsync controller.
2. Click [Preferences] - [Print job defaults].
3. Scroll down to the [Stacker] section.
4. Click the setting you want to change.
5. Change the value.
6. Click [OK].
20
Chapter 4 - Use the stacker
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the maximum stack height
Set the maximum stack height
Introduction
The maximum stack height is 355 mm (14") or 3,000 sheets A4/LTR (80 g/m² / 20 lb bond).
However, to guarantee a safe ejection of the stack, the factory default is set to 302 mm (11.9").
Depending on your needs, you can set the maximum stack height to a higher or lower value.
When the stack reaches the specified height, the stack is ejected.
Higher value
A higher value can be useful when you want to make optimal use of the output capacity in case of
unattended printing, for example.
However, when you set the value close to the maximum value, there is an increasing risk that
sets get split when the stack tray is almost full. Furthermore, curled paper or a slightly slanting
stack can touch the underside of the slide door during the ejection. This can result in sheets
falling off the stack.
Lower value
A lower value can be useful in the following situations, for example.
• When a stack must fit into a box.
• When a stack must fit the processable amount of sheets of specific offline finishing.
• When specific prints, such as curling prints or prints with an uneven toner coverage, result in
slanting stacks.
• When a stack becomes too heavy to lift manually.
Next job, next tray
NOTE
When the "next job, next tray" filling scenario is active (on the printer operator panel: [System] ->
[Setup] -> [Workflow profile] -> [Output] -> [Next output tray] -> [After each job]), the stack will
be ejected when the specified stack height is reached. The controller does not make sure that
sets are kept together.
Procedure
1. Access the Settings Editor on the PRISMAsync controller.
2. Enter the key operator password.
3. Click [Preferences] -> [Print job defaults].
4. Scroll down to the [Stacker] section.
5. Click [Maximum stack height].
6. Enter the desired stack height.
You can enter a value from 10 mm to 355 mm (0.4" to 14.0"). The factory default value is 302 mm
(11.9").
7. Click [OK].
Chapter 4 - Use the stacker
21
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the minimum filling level
Set the minimum filling level
Introduction
NOTE
The [Minimum filling level] setting is only applied when, on the printer control panel, the [Next
output tray] setting is set to [When tray is full] (under [System] -> [Setup] -> [Workflow profile] ->
[Output]).
Purposes
The [Minimum filling level] setting has the following purposes.
• Maximize the time that the printer can run unattended.
• Keep sets together.
Scenarios
The minimum filling level is a percentage of the specified maximum stack height. The following
scenarios can occur.
Scenarios to keep sets together
When
Then
A job is completed before the minimum filling The next job is delivered to the same output
level is reached
tray.
A job exceeds the minimum filling level
The stack will be ejected after the job is ready.
A set is completed before the minimum filling The next set is delivered to the same output
level is reached
tray.
A set exceeds the minimum filling level
The controller calculates whether the next set
can be added to the stack.
If the total stack height, including the next set,
is still lower than the maximum stack height,
then the next set is added to the stack.
If the total stack height, including the next set,
will become higher than the maximum stack
height, then the next set is added to the next
output tray available. The stack will be ejected
after the current set is ready.
Procedure
1. Access the Settings Editor on the PRISMAsync controller.
2. Enter the key operator password.
3. Click [Preferences] -> [Print job defaults].
4. Scroll down to the [Stacker] section.
5. Click [Minimum filling level].
6. Enter the desired filling level.
You can define a percentage from 1% - 100% in steps of 1%. The factory default value is 80%. This
value makes sure that, in most cases, sets are kept together.
7. Click [OK].
22
Chapter 4 - Use the stacker
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of using the [Maximum stack height] and the [Minimum filling level] settings
Examples of using the [Maximum stack height] and the
[Minimum filling level] settings
Example 1 - Fill a box
Assumption
In the Settings Editor, the [Maximum stack height] setting is set to 302 mm (11.9").
In the Settings Editor, the [Minimum filling level] setting is set to 80%.
1 job using plain paper with a stack height > 302 mm (11.9").
What happens?
If you want to fill a box, you can limit the maximum stack height to the height of that box. The
stacker:
• Fills the stack tray up to the specified height of 302 mm (11.9").
• Ejects the stack.
• Puts the rest of the job on the next output tray available.
302 mm / 11.9”
302 mm / 11.9”
80%
80%
Example 2 - Handle a slanting stack
Assumption
In the Settings Editor, the [Maximum stack height] setting is set to 250 mm (9.8").
In the Settings Editor, the [Minimum filling level] setting is set to 80%.
1 job using punched media with a stack height > 302 mm (11.9").
What happens?
Punched media can create a slanting stack. To prevent sheets from sliding off the stack, you can
limit the maximum stack height to 250 mm (9.8"), for example. The stacker:
• Fills the stack tray up to the specified height of 250 mm (9.8").
• Ejects the stack.
• Puts the rest of the job on the next output tray available.
Chapter 4 - Use the stacker
23
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of using the [Maximum stack height] and the [Minimum filling level] settings
250 mm / 9.8”
250 mm / 9.8”
80%
80%
Example 3 - Keep sets together
Assumption
In the Settings Editor, the [Maximum stack height] setting is set to 302 mm (11.9").
In the Settings Editor, the [Minimum filling level] setting is set to 80%.
1 job with a stack height of 100 mm (3.9").
4 copies required.
What happens?
The sets are stacked. At the end of each set, the controller calculates whether the next set will fit.
When the next set will not fit, the set is delivered to the next output tray available.
302 mm / 11.9”
302 mm / 11.9”
80%
80%
Example 4 - Keep jobs together
Assumption
In the Settings Editor, the [Maximum stack height] setting is set to 302 mm (11.9").
In the Settings Editor, the [Minimum filling level] setting is set to 80%.
4 different jobs with a stack height of 100 mm (3.9") each.
1 copy required.
What happens?
The jobs are stacked. At the end of each job, the controller calculates whether the next job will fit.
When the next job will not fit, the job is delivered to the next output tray available.
24
Chapter 4 - Use the stacker
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of using the [Maximum stack height] and the [Minimum filling level] settings
302 mm / 11.9”
302 mm / 11.9”
80%
80%
Example 5 - Two jobs exceed the maximum stack height
Assumption
In the Settings Editor, the [Maximum stack height] setting is set to 302 mm (11.9").
In the Settings Editor, the [Minimum filling level] setting is set to 80%.
On the printer operator panel, the workflow profile setting [Next output tray] is set to [When tray
is full].
2 different jobs with a stack height > 302 mm (11.9") each.
1 copy required
What happens?
Job 1 is stacked until a height of 302 mm (11.9") is reached. Then the stack with the partial job 1 is
ejected. The rest of job 1 is deposited on the stack tray. After you empty the stacker, job 2 will be
deposited the same way. Job 2 will not be deposited on top of job 1. The keep-jobs-together
function prevails.
302 mm / 11.9”
302 mm / 11.9”
302 mm / 11.9”
302 mm / 11.9”
80%
80%
80%
80%
Related information
Chapter 4 - Use the stacker
25
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Examples of using the [Maximum stack height] and the [Minimum filling level] settings
26
Chapter 4 - Use the stacker
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Error location labels
Error location labels
Introduction
The stacker has various labels inside that indicate error locations. You can access these locations
to remove error sheets or jammed paper.
Illustration
A2
A6
A3
A7
A4
A1
A5
[5] Example of a label inside the stacker
Error codes and locations
Overview of error codes and locations
Error codes
A1-A7
B1-B5
Error locations
Paper path
Paper path
Flip wheel
How to access the error locations
Open the front door.
Open the top cover.
C1
Open the front cover.
No label, only in- Stack area
dicated on the
Press the eject button.
stacker control
panel
28
Chapter 5 - Troubleshooting
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Error location labels
Chapter 5 - Troubleshooting
29
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove an error sheet from the internal error tray (A1)
Remove an error sheet from the internal error tray (A1)
When to do
A red LED lights up at the stacker control panel.
Illustration
[6] Indication at the stacker control panel
Remove an error sheet from A1
Step
Action
Illustration
1
Open the front door.
2
3
Remove the sheets from the internal error
tray (A1).
Close the front door.
30
Chapter 5 - Troubleshooting
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the input paper path (A2-A5)
Clear a paper jam in the input paper path (A2-A5)
When to do
A red LED lights up at the stacker control panel.
Illustration
[7] Indication at the stacker control panel
Clear a paper jam at A2-A5
Step
Action
Illustration
1
Open the front door.
2
Turn A7 to remove jammed paper.
CAUTION
When you turn the knob,
be careful not to get your
fingers caught.
3
Open A2, A3, A4 and A5 to remove the jam-
med paper.
4
Chapter 5 - Troubleshooting
31
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the input paper path (A2-A5)
Step
Action
Illustration
4
Close the front door.
32
Chapter 5 - Troubleshooting
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the input paper path of the registration unit (A6-A7)
Clear a paper jam in the input paper path of the
registration unit (A6-A7)
When to do
A red LED lights up at the stacker control panel.
Illustration
[8] Indication at the stacker control panel
Clear a paper jam at A6-A7
Step
Action
Illustration
1
Open the front door.
2
Turn A7 to remove the jammed paper.
CAUTION
When you turn the knob, be
careful not to get your fingers
caught.
4
Chapter 5 - Troubleshooting
33
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the input paper path of the registration unit (A6-A7)
Step
Action
Illustration
3
Remove the jammed paper from A6.
CAUTION
If the lower input paper path of
the registration unit also con‐
tains jammed paper, only au‐
thorized and trained persons
are allowed to remove the jam‐
med paper.
4
Close the front door.
34
Chapter 5 - Troubleshooting
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the paper path (B1)
Clear a paper jam in the paper path (B1)
When to do
A red LED lights up at the stacker control panel.
Illustration
[9] Indication at the stacker control panel
Clear a paper jam at B1
Step
Action
Illustration
1
Open the top cover.
2
Open B1 and remove the jammed paper.
4
Chapter 5 - Troubleshooting
35
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the paper path (B1)
Step
Action
Illustration
3
Close the top cover.
CAUTION
When you close the top cover,
be careful not to get your fin‐
gers caught.
36
Chapter 5 - Troubleshooting
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the horizontal paper path (B2-B5)
Clear a paper jam in the horizontal paper path (B2-B5)
When to do
A red LED lights up at the stacker control panel.
Illustration
[10] Indication at the stacker control panel
Clear a paper jam at B2-B5
Step
Action
Illustration
1
Open the top cover.
2
Open B2, B3, B4 and B5 to remove the
jammed paper.
4
Chapter 5 - Troubleshooting
37
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam in the horizontal paper path (B2-B5)
Step
Action
Illustration
3
Close the top cover.
CAUTION
When you close the top cover,
be careful not to get your fin‐
gers caught.
38
Chapter 5 - Troubleshooting
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam at the flip wheel (C1)
Clear a paper jam at the flip wheel (C1)
When to do
A red LED lights up at the stacker control panel.
Illustration
[11] Indication at the stacker control panel
Clear a paper jam at C1
Step
Action
Illustration
1
Open the front cover.
2
Open C1 and remove the jammed paper
from the flip wheel.
3
Close the front cover.
Chapter 5 - Troubleshooting
39
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Clear a paper jam at the flip wheel (C1)
40
Chapter 5 - Troubleshooting
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the EasyLift to unload the stacker
Use the EasyLift to unload the stacker
Introduction
The optional EasyLift is a manual device that helps you to remove a stack of paper more easily.
NOTE
The EasyLift is delivered with a user guide. Refer to the EasyLift user guide for more information.
This section contains a brief description for reference only.
Examples of stack weights
The tables below give an indication of the weights of stacks of paper.
• Green = OK to lift manually
• Red (strike-through) = too heavy to lift manually
Illustration
[12] The weight of stacks of 100, 500, 1,000 and 2,000 sheets - Examples for ISO media
[13] The weight of stacks of 100, 500, 1,000 and 2,000 sheets - Examples for US media
Use the EasyLift
Step
Action
Illustration
1
Slide the forks of the EasyLift under the
paper.
4
42
Chapter 6 - Options
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the EasyLift to unload the stacker
Step
Action
Illustration
2
When lifting, make sure to bend your
knees and keep your back straight.
CAUTION
Do not lift more than 15 kg (33
lb) to avoid physical injuries.
Please observe the national
health and safety regulations in
your country.
3
Lift the EasyLift to remove the paper from
the eject tray.
Make sure to place the EasyLift on a level
surface.
Chapter 6 - Options
43
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the EasyLift to unload the stacker
44
Chapter 6 - Options
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Specifications
Item
Specification
Paper size/weight/type
Paper size (Top tray, stack tray, eject tray):
A3, B4, A4R, A4, B5R, B5, A5R
LGL, LTR, LTRR, STMTR, SRA3, EXEC, EXECR
11" x 17", 12" x 18", 13" x 19"
Custom sizes: 140 mm x 182 mm - 330.2 mm x 487.7 mm
(5.5" x 7.2" - 13.0" x 19.2")
Weight*: 50 g/m² to 325 g/m² (13 lb bond to 120 lb cover)
Type: All media supported by printer
Tray capacity
Top tray: 200 sheets (80 g/m², 20 lb bond) (20 mm, 0.8" in
height)
Stack tray, eject tray: 3,000 sheets (80 g/m², 20 lb bond) or 355
mm (14.0") in height
Power source
90 V - 264 V, 47 Hz - 63 Hz, 10 A
300 W maximum
Maximum power consumption
Dimensions (H x W x D)
1,040 mm x 899 mm x 745 mm (40.9" x 35.4" x 29.3")
1,040 mm x 899 mm x 1,250 mm (40.9" x 35.4" x 49.2") (when
eject tray is ejected)
Weight
120 kg (264.6 lb)
* Paper weight differs depending on the connected host machine.
46
Appendix A - Specifications
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Index
C1.......................................................................39
Flip wheel..........................................................39
Horizontal paper path...................................... 37
Input paper path...............................................31
Input paper path of registration unit.............. 33
Paper path.........................................................35
E
Eject a stack manually
As soon as possible......................................... 16
Error sheet
A1...................................................................... 30
Power
F
Turn off............................................................. 15
Turn on..............................................................14
Examples.......................................................... 23
Filling scenarios
S
Filling level........................................................18
Limit the stack height.......................................18
Next job, next tray............................................18
Settings Editor
Face orientation................................................19
Feed edge......................................................... 19
Filling level........................................................19
Header orientation........................................... 19
Maximum stack height.................................... 19
Offset stacking..................................................19
Reverse order................................................... 19
Stacker.............................................................. 19
Stack height............................................................ 21
Stacker control panel
Eject button.......................................................10
LEDs.................................................................. 10
Status................................................................ 10
Straightest stacks possible.................................... 19
M
Main parts
Eject tray............................................................. 8
Front cover..........................................................8
Power switch...................................................... 8
Power switch cover............................................8
Slide door........................................................... 8
Stack tray............................................................ 8
Top tray...............................................................8
Maximum stack height...........................................21
Examples.......................................................... 23
Minimum filling level
T
Turn the stacker off................................................ 15
Turn the stacker on.................................................14
Examples.......................................................... 23
O
Optionals
EasyLift..............................................................42
P
Paper jam
A2-A5.................................................................31
A6-A7.................................................................33
B1.......................................................................35
47
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
48
Canon High Capacity Stacker-G1
Download from Www.Somanuals.com. All Manuals Search And Download.
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON U.S.A., INC.
One Canon Park, Melville, NY 11747, U.S.A.
CANON CANADA INC.
6390 Dixie Road Mississauga, Ontario L5T 1P7, Canada
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
CANON LATIN AMERICA, INC.
703 Waterford Way Suite 400 Miami, Florida 33126 U.S.A.
CANON AUSTRALIA PTY. LTD
1 Thomas Holt Drive, North Ryde, Sydney, N.S.W. 2113, Australia
CANON CHINA CO., LTD
15F Jinbao Building No.89 Jinbao Street, Dongcheng District, Beijing 100005, China
CANON SINGAPORE PTE. LTD.
1 HarbourFront Avenue #04-01 Keppel Bay Tower, Singapore 098632
CANON HONGKONG CO., LTD
19/F., The Metropolis Tower, 10 Metropolis Drive, Hunghom, Kowloon, Hong Kong
CANON INC. 2014
USRM2-5629-00
Download from Www.Somanuals.com. All Manuals Search And Download.
|