DVAS
Instruction Manual
EN Digital Video Array
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Safety Precautions
EN 3
WARNING:
For Indoor Product
Electrostatic-sensitive device. Use
proper CMOS/MOSFET handling
precautions to avoid electrostatic
discharge.
1. Water and Moisture - Do not use this unit near
water - for example, in a wet basement, in an
unprotected outdoor installation, or in any area
classified as a wet location.
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC SENSITIVE
DEVICES
2. Object and Liquid Entry - Never push objects of
any kind into this unit through openings, as they
may touch dangerous voltage points or short out
parts that could result in a fire or electrical shock.
Never spill liquid of any kind on the unit.
3. Power Cord and Power Cord Protection - For
units intended to operate with 230VAC, 50Hz,
the input and output power cord must comply
with the latest versions of IEC Publication 227 or
IEC Publication 245.
NOTE: Grounded wrist straps must be worn and proper ESD
safety precautions observed when handling the electrostatic-
sensitive printed circuit boards.
CAUTION: Lithium Battery
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer. Dispose of used
batteries according to the battery manufacturer’s
instructions.
Power supply cords should be routed so they are
not likely to be walked on or pinched. Pay
particular attention to location of cords and plugs,
convenience receptacles, and the point of exit
from the appliance.
Safety Precautions
4. Overloading - Do not overload outlets and
extension cords; this can result in a risk of fire or
electrical shock.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
For Outdoor Product
Power Lines - An outdoor system should not be
located in the vicinity of overhead power lines,
electric lights, or power circuits, or where it may
contact such power lines or circuits. When
installing an outdoor system, extreme care should
be taken to keep from touching power lines or
circuits, as this contact might be fatal. U.S.A.
models only - refer to the National Electrical
Code Article 820 regarding installation of CATV
systems.
This symbol indicates the presence of
uninsulated “dangerous voltage” within the
product’s enclosure. This may constitute a
risk of electric shock.
The user should consult the operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Attention: Installation should be performed by
qualified service personnel only in accordance
with the National Electrical Code or applicable
local codes.
For Rack-Mount Product
1. Ventilation - This unit should not be placed in a
built-in installation or rack, unless proper
ventilation is provided, or the manufacturer’s
instructions have been adhered to. The
equipment must not exceed its maximum
operating temperature requirements.
2. Mechanical Loading - Mounting of the
equipment in a rack shall be such that a
hazardous condition is not achieved due to
uneven mechanical loading.
Power Disconnect. Units with or without ON-
OFF switches have power supplied to the unit
whenever the power cord is inserted into the
power source; however, the unit is operational
only when the ON-OFF switch is in the ON
position. The power cord is the main power
disconnect for all units.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | FCC & ICES Information
EN 4
FCC & ICES INFORMATION
Sécurité
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION,
N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU
ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN COMPOSANT
SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILISATEUR. CONFIEZ
LA RÉPARATION DE L'APPAREIL À DU PERSONNEL QUALIFIÉ.
NOTE: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules and ICES-003 of
Industry Canada. These limits are designed to provide
reasonable protection against harmful interference
when the equipment is operated in a commercial
environment. This equipment generates, uses and
radiates radio frequency energy, and if not installed
and used in accordance with the instruction manual,
may cause harmful interference to radio
Ce symbole signale que le produit renferme une « tension
potentiellement dangereuse » non isolée susceptible de
provoquer une électrocution.
Ce symbole invite l'utilisateur à consulter les instructions
d'utilisation et d'entretien (dépannage) reprises dans la
documentation qui accompagne l'appareil.
Attention : l'installation doit exclusivement être réalisée par du
personnel qualifié, conformément au code national d'électricité
américain (NEC) ou au code d'électricité local en vigueur.
Coupure de l'alimentation. Qu'ils soient pourvus ou non d'un
commutateur ON/OFF, tous les appareils reçoivent de l'énergie une
fois le cordon branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque
le commutateur est réglé sur ON. Le débranchement du cordon
d'alimentation permet de couper l'alimentation des appareils.
communications. Operation of this equipment in a
residential area is likely to cause harmful interference,
in which case the user will be required to correct the
interference at his expense.
Intentional or unintentional changes or modifications,
not expressly approved by the party responsible for
compliance, shall not be made. Any such changes
or modifications could void the user’s authority to
operate the equipment. If necessary, the user should
consult the dealer or an experienced radio/television
technician for corrective action.
The user may find the following booklet, prepared by
the Federal Communications Commission, helpful:
How to Identify and Resolve Radio-TV Interference
Problems. This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402,
Stock No. 004-000-00345-4.
Sicherheitshinweise
VORSICHT: UM EINEN ELEKTRISCHEN SCHLAG ZU
VERMEIDEN, IST DIE ABDECKUNG (ODER RÜCKSEITE) NICHT
ZU ENTFERNEN. ES BEFINDEN SICH KEINE TEILE IN DIESEM
BEREICH, DIE VOM BENUTZER GEWARTET WERDEN
KÖNNEN. LASSEN SIE WARTUNGSARBEITEN NUR VON
QUALIFIZIERTEM WARTUNGSPERSONAL AUSFÜHREN.
Das Symbol macht auf nicht isolierte „gefährliche Spannung"
im Gehäuse aufmerksam. Dies kann zu einem elektrischen
Schlag führen.
WARNING: This is a Class A product. In a domestic
environment, this product may cause radio
interference, in which case, the user may be required
to take adequate measures.
Der Benutzer sollte sich ausführlich über Anweisungen für
die Bedienung und Instandhaltung (Wartung) in den
begleitenden Unterlagen informieren.
Achtung! Die Installation sollte nur von qualifiziertem
Kundendienstpersonal gemäß jeweils zutreffender
Elektrovorschriften ausgeführt werden.
Unterbrechung des Netzanschlusses. Geräte mit oder ohne
Netzschalter haben Spannung am Gerät anliegen, sobald der
Netzstecker in die Steckdose gesteckt wird. Das Gerät ist jedoch
nur betriebsbereit, wenn der Netzschalter (EIN/AUS) auf EIN
steht. Wenn das Netzkabel aus der Steckdose gezogen wird, ist
die Spannungszuführung zum Gerät vollkommen unterbrochen.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Safety Precautions
EN 5
Precauciones de Seguridad
Sicurezza
PRECAUCIÓN: PARA DISMINUIR EL RIESGO DE DESCARGA
ELÉCTRICA, NO RETIRE LA CUBIERTA (NI LA PARTE
POSTERIOR). NO EXISTEN PIEZAS DE RECAMBIO EN EL
INTERIOR DEL EQUIPO. EL PERSONAL DE SERVICIO
CUALIFICADO SE ENCARGA DE REALIZAR LAS
REPARACIONES.
ATTENZIONE: PER RIDURRE IL RISCHIO DI SCOSSE
ELETTRICHE NON RIMUOVERE LA COPERTURA (O IL
PANNELLO POSTERIORE). L'UNITÀ NON CONTIENE
COMPONENTI INTERNI RIPARABILI DALL'UTENTE. PER
QUALSIASI INTERVENTO, RIVOLGERSI A PERSONALE
TECNICO QUALIFICATO.
Este símbolo indica que existen puntos de tensión peligrosos
sin aislamiento dentro de la cubierta de la unidad. Estos
puntos pueden constituir un riesgo de descarga eléctrica.
Questo simbolo indica la presenza di "tensione pericolosa" non
isolata all'interno del contenitore del prodotto. Ciò comporta
un potenziale rischio di scosse elettriche.
El usuario debe consultar las instrucciones de funcionamiento y
mantenimiento (reparación) en la documentación que se
suministra con el aparato.
Si consiglia di consultare le istruzioni operative e di
manutenzione (interventi tecnici) contenute nella
documentazione fornita con il dispositivo.
Atención: la instalación la debe realizar únicamente personal
cualificado de conformidad con el National Electric Code o las
normas aplicables en su país.
Attenzione: l'installazione deve essere effettuata esclusivamente
da personale tecnico qualificato in conformità con il National
Electrical Code o con le normative locali vigenti.
Desconexión de la alimentación. Las unidades con o sin
interruptores de encendido/apagado reciben alimentación
eléctrica siempre que el cable de alimentación esté conectado a
la fuente de alimentación. Sin embargo, la unidad sólo funciona
cuando el interruptor está en la posición de encendido. El cable
de alimentación es la principal fuente de desconexión de todas
las unidades.
Scollegamento dell'alimentazione. Le unità dotate o sprovviste di
interruttori ON-OFF vengono alimentate quando si inserisce il
cavo nella presa dell'alimentazione. L'unità è tuttavia in funzione
solo quando l'interruttore ON-OFF si trova nella posizione ON. Il
cavo di alimentazione costituisce il dispositivo di scollegamento
dell'alimentazione principale per tutte le unità.
Veiligheidsmaatregelen
Medidas de Segurança
VOORZICHTIG: OPEN DE BEHUIZING OF DE ACHTERKANT
VAN HET APPARAAT NIET. ZO VERMINDERT U HET RISICO
OP ELEKTRISCHE SCHOKKEN. IN HET APPARAAT
BEVINDEN ZICH GEEN ONDERDELEN DIE U ZELF KUNT
REPAREREN. LAAT SERVICE EN ONDERHOUD UITVOEREN
DOOR GEKWALIFICEERD PERSONEEL.
CUIDADO: PARA REDUZIR O RISCO DE CHOQUE
ELÉCTRICO, NÃO RETIRE A TAMPA (OU A PARTE
POSTERIOR). NO INTERIOR, NÃO EXISTEM PEÇAS QUE
POSSAM SER REPARADAS PELO UTILIZADOR. REMETA A
ASSISTÊNCIA PARA OS TÉCNICOS QUALIFICADOS.
Este símbolo indica a presença de "tensão perigosa" não
isolada dentro da estrutura do produto, o que pode constituir
risco de choque eléctrico.
Dit symbool geeft aan dat er binnen in het apparaat
ongeïsoleerde, gevaarlijke spanning aanwezig is die mogelijk
elektrische schokken kan veroorzaken.
O utilizador deve consultar as instruções de funcionamento
e manutenção (assistência) nos documentos que
acompanham o aparelho.
De gebruiker dient de bedienings- en onderhoudsvoorschriften
te raadplegen in de documentatie die werd meegeleverd met
het apparaat.
Atenção: a instalação deve ser executada apenas por técnicos
qualificados da assistência, de acordo com o código eléctrico
nacional ou os códigos locais aplicáveis.
Attentie: het apparaat mag alleen door gekwalificeerd personeel
worden geïnstalleerd. De installatie dient in overeenstemming
met de nationale elektrische richtlijnen of de van toepassing
zijnde lokale richtlijnen te worden uitgevoerd.
Corte de corrente. As unidades com ou sem interruptores
ON-OFF (ligar/desligar) recebem corrente sempre que o fio de
alimentação está introduzido na fonte de alimentação; contudo, a
unidade apenas está operacional quando o interruptor ON-OFF
está na posição ON. O fio de alimentação destina-se a desligar a
corrente em todas as unidades.
Spanning uitschakelen. Apparatuur met of zonder
aan-uitschakelaar staat onder spanning zolang de stekker is
aangesloten op de wandcontactdoos. De apparatuur is uitsluitend
in werking als de aan-uitschakelaar aan staat. Het netsnoer is de
"hoofdschakelaar" voor alle apparatuur.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Safety Precautions
EN 6
Zasady Bezpieczeństwa
PRZESTROGA: ABY ZMNIEJSZYĆ RYZYKO PORAŻENIA
ELEKTRYCZNEGO, NIE NALEŻY ZDEJMOWAĆ POKRYWY
GÓRNEJ (ani tylnej). WEWNĄTRZ URZĄDZENIA NIE MA
ŻADNYCH ELEMENTÓW, KTÓRE MOGĄ BYĆ NAPRAWIANE
SAMODZIELNIE PRZEZ UŻYTKOWNIKA. SERWIS NALEŻY
ZLECAĆ WYKWALIFIKOWANYM PRACOWNIKOM OBSŁUGI.
Ten symbol wskazuje na obecność nieizolowanego
„niebezpiecznego napięcia” we wnętrzu urządzenia. Napięcie
to grozi porażeniem elektrycznym.
Użytkownik powinien zapoznać się z instrukcjami obsługi i
konserwacji (serwisu), zamieszczonymi w dokumentacji
towarzyszącej urządzeniu.
Uwaga: Instalacja może być wykonywana wyłącznie przez
wykwalifikowanych pracowników obsługi, zgodnie z zasadami
kodeksu National Electrical Code lub innych obowiązujących
norm.
Odłączanie zasilania Niezależnie od wyposażenia w wyłącznik
zasilania, prąd do urządzenia jest doprowadzany zawsze, gdy
przewód zasilania jest podłączony do źródła zasilania; jednak
urządzenie działa tylko wtedy, gdy wyłącznik zasilania jest
włączony. Przewód zasilania jest głównym wyłącznikiem zasilania
we wszystkich urządzeniach.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Table of Contents
EN 7
Table of Contents
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
FCC & ICES Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
1
PRODUCT INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
UNPACKING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Safety Concerns . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Serviceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
PHYSICAL COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
RAID Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Hard Drive Assemblies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
PRODUCT OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
LED DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Basic Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Setting Up the Network Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Manually Setting the IP Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Quick Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Setting Up SCSI Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Creating a RAID Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Adding and Mapping a Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
BOSCH (GUI) Graphic User Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Menu Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Information Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
RAID Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Volumes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Progress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Disk Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Network Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
1.1
1.2
1.3
2
2.1
2.2
3
3.1
3.2
3.3
4
5
5.1
6
6.1
6.2
6.3
6.4
6.5
6.6
6.7
7
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10 Bad Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
7.11 Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
7.12 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
7.13 Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
8
RAID MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Add Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Add Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Expand Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Delete Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
8.1
8.2
8.3
8.4
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Table of Contents
EN 8
8.5
8.6
8.7
8.8
8.9
Map Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Rename Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Rename Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Delete Array . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Add Spare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
8.10 Delete Spare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
9
SYSTEM MENU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
SCSI Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Network Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
E-Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
Date + Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Cache Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Administration Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
LOG OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
ADDITIONAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
10
11
11.1 Required Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
11.2 Rail Kit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
12
13
14
TECHNICAL SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
FIRMWARE UPDATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
APPENDIX A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Product Introduction
EN 9
1
PRODUCT INTRODUCTION
2
UNPACKING
DVAS Series Digital Video Array is a high speed, fault
tolerant RAID subsystem design. It uses a mid-plane
design to eliminate the problems associated with cable
interconnects. Unlike conventional RAID products, the
DVAS Series disk array uses ATA disk drives to store
RAID data, rather than high cost SCSI or Fiber Channel
disks. Its advanced electronic soft-start technology makes
hot-swappable ATA drives very reliable.
2.1 Safety Concerns
•
Computer components and disk drives are
sensitive to static charge. Take precautions to
divert any electrostatic charge from your person
before and while handling the components with
your hands or any tools.
•
•
Before removing Controllers or Power Supplies,
ensure that the system is powered down and
disconnected from the main socket.
1.1 Models
Model
Number of DVRs
Connected
Allocation of
Storage
Ensure correct lifting methods are used when
handling the DVAS Series disk array. Special
care should be taken when removing the
DVAS Series disk array from its packaging and
positioning it in the required location.
4 Hard Drive
Model
1 DVR (Channel 0)
100% to Host Port 0
8 Hard Drive
Model
1 DVR (Channel 0)
100% to Host Port 0
50% to Host Port 0
•
When installing DVAS Series disk array as a
rack-mounted component, ensure that all
fixtures are secure. All bolts and screws should
be fully tightened. Failure to comply with this
may result in the unit not being fully supported
in the rack and could lead to the product
dropping out of rack or falling onto other rack
components.
14 Hard Drive 2 DVRs
Model
(Channel 0 + Channel 1) 50% to Host Port 1
1.2 Accessories
The DVAS includes a controller board, power supply,
SCSI cable, and specified number of hard disks.
Item
Type#
Controller Board
Power Supply
ACCCB
ACCPS
•
EMC Regulations require that all data and
network cables be the shielded type. Special
care should be taken to ensure that the network
cable is shielded and that the shield is connected
at both ends.
Hard Disk Assembly (160 GB or 300 GB) (ACCDC016M or
ACCDC030M)
SCSI cable
SCSIVHD50
WARNING:
Electrostatic-sensitive device. Use
proper CMOS/MOSFET handling
precautions to avoid electrostatic
discharge.
1.3 Features
•
RAID 5 Protection with up to 3.9Terabytes of
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
Video Storage
ELECTROSTATIC SENSITIVE
DEVICES
•
•
•
•
Up to 14 Hot-swappable Disk Drives
19-in 3U Rack-mount Chassis
NOTE: Grounded wrist straps must be worn and proper ESD
safety precautions observed when handling the electrostatic-
sensitive printed circuit boards.
Hot Spare and Automatic Rebuild
CAUTION: Lithium Battery
Modular Design for Easy Service, with Optional
Redundant Power Supply and Controller Board
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer. Dispose of used
batteries according to the battery manufacturer’s
instructions.
•
•
Web-based GUI with Quick Configuration page
Dual Host Capability, Providing Storage for
Two (2) DVRs
•
•
Auto-terminating SCSI Ports
ATA Mid-plane Design, for Added Reliability
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Unpacking
EN 10
On receipt of your DVAS Series disk array, ensure that
no damage has been sustained in transit and that you
have received the following items:
2.2 Serviceable Parts
This product has no user serviceable parts. Any
attempts to remove this product’s cover may result in
loss of warranty. If the unit ever needs repair service,
contact the nearest Bosch Security Systems, Inc.
Service Center for a return authorization number and
shipping instructions.
•
•
DVAS Chassis with Controller Board and Power
Supply/Fan Assembly Installed
Hard Disk Assemblies1 (ACCDC016M or
ACCDC030M)
Service Centers
U.S.A.: Phone: 800-366-2283 or 408-956-3895
•
•
•
•
•
Blank Panels1 (ACCBP)
fax:
800-366-1329 or 408-956-3896
SCSI Cable (SCSIVHD50)
Power Cords (2; America and European types)
Mounting Hardware
e-mail: [email protected]
514-738-2434
Canada:
Europe, Middle East & Asia Pacific Region:
32-1-440-0711
For additional information,
This Instruction Manual
1The supplied quantity is dependent upon the model purchased. The
number of Hard Disk Assemblies and blank panels should total 14.
3
PHYSICAL COMPONENTS
NOTE: For proper cooling of the unit, blank panels
must be installed.
3.1 Power Supplies
3.1.1 Insertion
Pull the handle of the Power Supply Unit (PSU) so
that it is at 90° to the main PSU unit. Line up the PSU
with the guide rails in the DVAS Series. Insert the PSU
gently until it comes to a halt, then close the handle
and secure it in place with the attached screw.
The shipping carton is the safest container in which to
transport the unit. Save it and all packing materials for
future use.
3.1.2
Removal
Turn off the power switch. Disconnect the
power cord, loosening the cable clamp if
necessary. Loosen the screw on the power
supply by turning it counterclockwise. Pull out
the handle of the PSU so that it is 90° to the
chassis. While supporting the weight of the
PSU during removal, use the handle to pull
the power supply free from the chassis.
Figure 1 Components
If your DVAS has the dual redundant power
supply option, it is permissible to remove and
replace a faulty power supply while the unit is
operational. Only remove a power supply from
a working unit if it is faulty and a replacement is
on-site. Removing a PSU when no replacement
is immediately available may result in
overheating and shutdown. When removing a
faulty power supply, be sure to remove the
correct one; faulty power supplies have no green
status LED illuminated on the rear panel.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Physical Components
EN 11
3.2 RAID Controller
3.2.1 Insertion
A RAID controller should not be inserted while the
unit is powered on. Shut down before replacing a
faulty RAID controller.
Insert the RAID controller into its slot, lining up the
metal runners with the internal guides. Firmly push the
RAID controller fully into the chassis until the side
clips click into place.
3.2.2 Removal
Power down before removing a faulty
controller.
Push the controller side clips inward (towards each
other). While supporting the weight of the unit, use the
handles to pull the controller free from the unit.
3.3 Hard Drive Assemblies
3.3.1 Insertion
Align the disk carrier with an available disk slot.
Ensure that the handle is open and the carrier push
button is toward the bottom of the chassis. Push the
disk carrier until fully inserted, then close the handle
and push in the carrier button to secure the chassis in
place.
3.3.2 Removal
Do not remove a disk while in operation within a
RAID set, as this will cause the RAID set to degrade.
Only remove a disk marked as bad by the GUI and
having an amber LED illuminated beneath it. To
remove a disk, push the button on the disk carrier,
releasing the handle. Gently pull the bottom of the
handle toward you and wait for ten seconds for the
disk to stop spinning, then continue sliding the disk
out of the chassis.
Disk drives are sensitive to static electricity
and physical shock. Observe proper ESD
precautions and handle with care.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | Product Overview
EN 12
4
PRODUCT OVERVIEW
Drive Module
Chassis Services LEDs
Reset Button
Drive Status Indicators
Drive Release Button
Drive Release Lever
Figure 2 DVAS Front
Power Switch
Fan or Optional Power Supply
Mains Connector
Release Lever
Raid Controller
Release Caps
Serial Port
Network Connector
Blank Panel
Figure 3 DVAS Rear
Disk Channel &
Loop Through
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS Series | Instruction Manual | LED Display
EN 13
5
LED DISPLAY
Temperature + Ventilation Status
Power Supply Status
Management Alarm
Silence Button
Disk Activity
Disk Drive Alarm
Figure 4 LED Display
5.1 Status Indicators
LED
Status
Temperature and Ventilation Status
GREEN LED indicates that blowers are operating at an acceptable RPM, and the internal
temperature sensors are within acceptable limits.
Alternating GREEN and RED LED indicates a predicted blower failure, or rapid temperature
increase.
RED LED indicates that a blower has failed, or the unit is too hot; an audible alarm will also
sound.
Power Supply Status
GREEN LED indicates both power supplies are functional.
RED LED indicates either power supply has failed; an audible alarm sounds. In this case, the LEDs
on each power supply should be examined to determine which has failed.
IMPORTANT:
•
Inadvertently removing the functional, surviving power supply will result in system failure and
possible data loss.
A failed power supply or blower should be replaced as quickly as possible. Do not remove the
failed power supply until a replacement is on hand. Continued operation with a failed power
supply or blower will result in a dramatic, irreversible reduction in system life.
•
Management Alarm
Silence Button
GREEN LED indicates normal status.
RED LED indicates a RAID controller board error.
Insert a paper clip to silence the audible alarm, or to confirm creation of a RAID set.
Disk Drive Alarm
Disk Drive Activity
AMBER LED indicates that a drive is suspected to be bad.
GREEN LED indicates that an installed drive is in a ‘ready’ state. During activity, the LED will
flicker.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Before You Begin
EN 14
These configurations suit most applications, but if not,
or to use additional features, you must set up the
network connection and access the GUI. See
6
BEFORE YOU BEGIN
Ensure the following:
•
•
Installation environment is less than 40°C.
SECTION 6.2, Setting up the Network Connection.
The front drive bays and rear ventilation panels
are not obstructed.
Use the GUI interface to:
•
Add a Hot Spare.
•
Main Power is sufficient to handle the load of
the system.
•
Add Drive(s) (if storage is expanded, the entire
RAID must be reconstructed).
•
Rack is properly grounded.
•
Change the allocation of storage (only applicable
if two DVRs are connected to a single DVAS).
Tips for Rack-mounting:
•
•
Monitor the DVAS system.
•
Remove the power supplies and hard disk
canisters to make the system lighter.
Use the e-mail alert feature (warnings and error
messages can be e-mailed to a specified address).
•
•
•
Request assistance to lift the unit into the rack.
Do not to trap fingers or items of clothing.
•
•
Attach two DVRs to a DVAS0416 or a
DVAS0816 unit (see Quick Configuration page).
Ensure all fixtures are secure and bolts and
screws are fully tightened.
Attach only one DVR to a DVAS1416 (see Quick
Configuration page).
6.1 Basic Installation Steps
1. Attach the SCSI cable from the DVR to the
DVAS.
6.2 Setting up the Network Connection
To use the web-based GUI, perform the following:
1. Attach a network cable from the DVAS’s
Ethernet port to a network. A simple crossover
cable can be used from a PC to the DVAS’s
Ethernet port.
If only one DVR is connected to the DVAS, ensure
that the cable is connected to Channel 0. Refer to
SECTION 4.0, PRODUCT OVERVIEW.
2. Attach the power cord(s) to the disk array and
apply power to the unit.
2. Access any computer on the network.
If no crossover cable was used to connect the unit to a
network, the network’s subnet mask may not allow access
to this IP address without some reconfiguration. Access
the DVAS Series disk array via a shell or DOS prompt
on the host computer and enter the following command.
If an audible alarm is heard, the DVAS unit does not
have a RAID group configured, or no disks are
present.
3. Wait one minute and apply power to the DVR
unit.
®
Windows
:
route add 10.11.12.13 mask 255.255.255.255 <workstation IP number>
4. Configure the DVR for archiving (see DVR
instruction manual).
Linux:
/sbin/route add 10.11.12.13/32 gw <workstation IP number>
Solaris:
5. Depending upon the model purchased, the
DVAS unit is preconfigured.
route add 10.11.12.13 mask 255.255.255.255 <workstation IP number>
Where <Workstation IP number> refers to the IP
address of the workstation being used. The DVAS
Series disk array’s web interface is now accessible via a
standard browser (Netscape or Internet Explorer).
For your convenience, DVAS disk arrays are shipped
with drives preconfigured for RAID.
Model
Number of DVRs Connected
Allocation of Storage
4 Hard Drive Model
8 Hard Drive Model
14 Hard Drive Model
1 DVR (Channel 0)
100% to Host Port 0
1 DVR (Channel 0)
100% to Host Port 0
2 DVRs (Channel 0 + Channel 1)
50% to Host Port 0; 50% to Host Port 1
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Before You Begin
EN 15
6.3 Manually Setting the IP Address
Using a web browser program (Netscape or Internet
Explorer), type the unit’s IP address in the URL and
press GO (the default IP address is 10.11.12.13).
Figure 5 Setting the IP Address
When the login page is displayed, click Login to
continue; by default, no user name or password is
required.
From this Main page, click System, located at the
middle of the left-hand side of the screen.
Figure 6 System Setting
Then select the Net Settings tab.
Figure 7 Net Settings
By default, the Net Settings new page requests a user
name and password:
User name = ADMIN
Password = PASSWORD
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Before You Begin
EN 16
The main frame will change to the Network Settings
Web Page Auto Refresh
page. Insert the new settings into the text boxes.
Determines whether the web pages should be reloaded
at a specified interval, to show any changes to the
system on-screen. If desired, ensure that the Enabled
box is checked. A value (number of seconds) must be
specified, to indicate the frequency of refreshing the
web page.
When all settings have been updated, press Save
Configuration.
Restart the system to activate these changes.
6.4 Quick Configuration
THIS PROCESS CLEARS ALL DATA!
Figure 8 Network Settings
The DVAS can be fully configured with the Quick
Config function. To access this function, click Quick
Config, in the left-hand menu of the main web page.
How to Set IP Address
Decide whether to use DHCP (Dynamic Host
Configuration Protocol), or a manually set IP address.
Use the radio buttons to select the desired value. If
choosing DHCP, no further values are required. It is
recommended that you have your DHCP server
reserve a static IP for your DVAS Series disk array.
When the Quick Config page loads, select one of two
configurations by clicking on one of the page tabs at
the top of the page. Configuration options are:
1 DVR CONFIG: Select if your unit is to be used with
a single DVR.
IP Address
2 DVR CONFIG: Select if you wish to attach two
DVRs to the unit.
If setting up the network manually, enter a free IP
address into the text box.
The selected DVR Config tab displays the status of the
configuration, identifying the settings to be configured.
Subnet Mask
Type the appropriate subnet mask for the class of your
network. In most cases 255.255.255.0 is fine, but
Bosch recommends contacting your IT administrator
for further assistance.
Gateway
Type the IP address of your Internet gateway here.
Figure 9 DVR Config
Primary/Secondary DNS
Type the IP address of both the Primary and
Secondary DNS into the text boxes.
The status column (on the right side) will display either
OK, or Needs Configuring. If all settings report OK, there
is no need to continue. To continue with the automatic
configuration, scroll to the bottom of the Quick Config
window.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Before You Begin
EN 17
Check the check box and click Quickstart configure for
(x) DVR.
SCSI ID
Use the drop down menu to choose the desired ID.
Termination
AUTOMATIC is the default setting and will work with
all Bosch DVRs.
SCSI Max Transfer Rate
Defines the maximum speed of the SCSI bus. The
default setting for the DVAS is Ultra2. This setting
should only be changed if the DVR specifies a
different setting.
Figure 10 Quick Config Confirmation
Quick Config adjusts the settings required to configure
the disk array to work with 1 or 2 DVRs. If prompted
for a system reboot, manually cycle the power
switches. Once the system reboots, Quick Config has
finished.
Click Save Settings to save these settings.
Power cycle the unit so the new Network and SCSI
settings are applied.
6.5 Setting Up SCSI Interfaces
The DVAS Series disk array’s SCSI settings are
preconfigured to work with Bosch DVRs, without any
adjustments.
To accommodate future products, the SCSI settings
may be altered. This section explains each setting.
To change the SCSI setting select System on the
DVAS Series disk array’s main page.
Figure 11 SCSI Interfacing
Select the SCSI tab to access the SCSI settings.
When the Configure SCSI page is loaded in the main
frame, use the drop down menus to select the new
setting for the SCSI host channels.
Figure 12 SCSI Settings
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Before You Begin
EN 18
Use the tick boxes to select the drives to be used in the
array.
6.6 Creating a RAID Set
As stated earlier, the DVAS is shipped with drives
preconfigured for RAID. However, if any of the
following occurs, you must create a RAID set.
NOTE: Unused disks are not automatically used as
spares.
•
New drives have been added, and are to be part
of the RAID set.
Select RAID Level
Choose the RAID level that best suits your application
via the drop down menu.
•
The RAID set was destroyed (this could happen
if two or more drives failed at the same time).
Select Stripe Size
Current DVRs require a stripe size of 64KB, although
future products may require a different setting. Use the
drop down menu to select the desired stripe size for
the array.
To create a RAID set, the default volume and RAID
set must be deleted. To do this, click RAID, on the
left-hand side of the main page, and select the Delete
Volume tab from the top bar.
Once all settings are complete, press Create RAID
Set to continue.
The configured volumes will be listed. Click the radio
button of the volume to be deleted, then Delete
Volume. Respond to the confirmation message as it
appears.
When the new page is displayed, click Delete Array.
Click the radio button of the array to be deleted, then
click Delete RAID Array.
Figure 14 Creating a RAID Set
The RAID set will begin building. Array construction
can take several hours to complete. Monitor the
progress from the Progress page by clicking
Information, at the left-hand side of the page. Select
the Progress tab to show an overview of all utilities
running on the array.
NOTE: Only one array can be deleted at a time.
When prompted, confirm the deletion by clicking the
tick box in the center of the screen, then Confirm
Delete Command. To cancel the command, click
CANCEL Delete.
Select the Add Array tab.
Figure 13 Configuring a RAID Array
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Before You Begin
EN 19
Stages of Array Mapping:
Reserve an optional free space area at the
•
Array Construct: Writes the RAID stripes to
disk.
beginning of the new volume for future expansion
of a previous volume. A volume can only be
expanded in this way. Data on a volume must be
sequential; it is not possible to add data on an array
unless it directly follows the volume.
•
Array Verify: Verifies that data can be read
from each block of the array.
Dependant on disk capacity, it can take up to six hours
to create a RAID Set.
Select logical unit number (LUN) for new volume
on host 0/1. Use the drop down menu to define the
LUN for each volume, on one or both Host Channels.
6.7 Adding and Mapping a Volume
NOTE: It is recommended to use the Quick
Configuration page for adding and mapping volumes.
This section may be used for future DVRs requiring
more sophisticated volume mapping.
A LUN can only be accessed by one DVR.
To confirm your choices, select the Add Volume tab. To
create more than one array, enter this page again using
the left-hand menu.
New arrays must be partitioned, via ADD VOLUME.
A maximum of 16 volumes can be created (with a
maximum of eight volumes per channel). Once a
volume has been created, it must be mapped to a
LUN or LUNs, and Host Channel or Channels.
Once the volumes have been created and mapped,
restart the computer to access the DVAS Series disk
array.
To create a volume, click RAID, at the left-hand side
of the main page, then select the Add Volume tab.
Figure 15 Creating Volume
Enter the name for the new volume to define the
friendly name of the volume, for use in the GUI.
Enter the size of the new volume in
Megabytes (MB). You may create one volume that
is the maximum size of the array, or a number of
volumes. The remaining free space on the array is
shown at the bottom of the screen.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Bosch GUI
EN 20
7
Bosch GUI
(Graphic User Interface)
7.1 Menu Tree
Home
Information
RAID Arrays
– Volumes
– Drives
– Progress
– System Information
– Disk Statistics
– Network Statistics
– Bad Blocks
– Problems
– Event Log
– Key
RAID Menu
Add Array
– Add Volume
– Expand Volume
– Delete Volume
– Map Volume
– Rename Volume
– Rename Array
– Delete Array
– Add Spare
– Delete Spare
System Menu
SCSI
– Network Settings
– Network Port
– E-Alerts
– Date & Time
– Security
– Multi View
– Config Dump
– Cache
– Admin
– Tech Support
Quick Configuration
1 DVR
– 2 DVR
Home
Log Off
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Bosch GUI
EN 21
7.2 Information Menu
Click Information to view various information. No
edit capability is available from this view.
Use the tabs to access the various pages.
Figure 16 Information Menu
Available Information:
7.3 RAID Array
This page provides information on the created array.
Information
Description
Array Number
Reference number, normally given in
order of creation.
Array Name
User-defined label for array.
Array Status / Health
Current health value. Fault Tolerant/Not
Fault Tolerant/Critical/Offline.
RAID Level
Displays the RAID level of the array.
Array Capacity
Displays array capacity in Gigabytes (GB).
No. of Array Members Displays the number of disks in the array.
No. of Spares
Displays total number of spares for the
array.
No. of Volumes
Displays total number of configured
volumes for the array.
Data Stripe Size
Write Cache
Displays stripe size for the array.
Displays whether write caches are
enabled or disabled.
Figure 17 RAID Array Information
Write Cache Size
Rebuild Priority
Verify Utility
Displays the amount of write cache.
Displays the user-definable rebuild rate.
Displays the time and type of the next
scheduled array verification.
Verify Utility Interval
Displays frequency of verification.
Time Created
Date Created
Displays the time of the array creation.
Displays the date of the array creation.
You may need to scroll the browser to the right to see
all of the disks.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Bosch GUI
EN 22
Click on a drive to view its information.
7.4 Volumes
This page provides information on the volumes within
the created array.
Figure 20 Drive Information
Available Information:
Information
Status
Description
Displays ownership status.
Figure 18 Volume Array
Capacity
Model
Displays raw capacity of disk drive.
Displays manufacturer’s drive model
number.
Available Information:
Information
Description
Serial Number
Firmware
Displays serial number of the drive.
Volume Name
Volume Capacity
User-defined name for the volume.
Displays current firmware level of drive.
Size of the volume in Megabytes;
[Gigabytes in brackets].
R/W Transfer Retries
Displays number of transfer retries
(normally 0).
Percentage of Total
Array Used
Displays the percentage of the entire
array capacity that’s used by the volume.
R/W Media Retries
Displays number of media retries
(normally 0).
Host 0/1 Target ID:
LUN
Displays the SCSI ID and LUN of the
array, on both host channels.
R/W Transfer Retries and R/W Media Retries can
indicate problems with a disk. Retries are generally not
harmful, but more than ten retries in a 24-hour period
are cause for concern, particularly if one or two disks
consistently have a higher retry count than the others.
Contact technical support for further guidance.
Volume Serial Number Displays the volume serial number, which
may be required for some SCSI tasks.
Volume Creation Time Displays the time of volume creation.
Volume Creation Date Displays the date of volume creation.
7.6 Progress
7.5 Drives
This page shows the progress of certain array utilities.
This page provides extended information about the
The following progress is viewable on this screen:
ATA disks installed within the array.
Figure 19 Drive Array
Figure 21 Array Utilities
•
•
•
•
Array Construct (create)
Array Verify
Array Reconstruct (rebuild)
Consistency check
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Bosch GUI
EN 23
Available Information:
This page may help with troubleshooting.
7.7 System Information
This page provides information regarding non-disk
hardware.
Information
Cooling
Description
Displays the status of the blowers.
Power
Displays the status of the power
supplies.
Voltage
Displays Rail, CPU, and Battery voltages.
Temperature
Displays controller and battery
temperature.
Charge Mode
Time
Displays battery charging mode.
Displays current time.
Date
Displays current date.
Firmware version
Displays the firmware version.
Web GUI version
Write Cache
Displays the version of the WEB GUI.
Displays the write cache amount and
status.
Figure 22 System Information
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Bosch GUI
EN 24
7.8 Disk Statistics
The page shows information on the disks in the
system.
Figure 23 Disk Statistics
Each disk displays its Reads, Writes, Others, Transfer
Retries, and Media Retries. If a disk is generating
errors, it may fail sometime in the future. RAID 5
configurations should distribute reads and writes
evenly among all of the drives.
Available Information:
Information
Description
IOs
Displays the number of requested IOs by the
host system. The individual figures represent
each request. Note that a single request may
be up to 255 blocks long.
Transfer Retries
Media Retries
Displays the number of failure instances due
to a problem between the RAID controller and
the ATA disk; normally 0.
Displays the number of failure instances due
to bad surface media on the hard disk;
normally 0, although a moderate amount of
retries is acceptable.
Read
Write
Other
Number of host reads.
Number of host writes.
Number of accesses to RAID configuration
and/or GUI information (event log, etc.) on the
disk.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Bosch GUI
EN 25
7.9 Network Statistics
7.10 Bad Blocks
This page provides information about the network
link. If you are having problems with the network, this
page may be helpful.
Bad blocks are sections of the disk that data can no
longer be read from or written to. A DVAS array
automatically remaps single bad blocks to a spare
blocks portion of the disk when using a parity-
protected RAID level. However, if two bad blocks are
discovered at once, that block of data is lost. This is
most likely to happen during a rebuild, or when one
disk is missing and another disk has a media error. In
general, bad blocks are unlikely to occur.
This page shows the number of bad blocks for each
drive. If there are bad blocks present, their location
can be viewed by clicking Details (in the right-hand
column).
Figure 24 Network Statistics
Available Information:
Figure 25 Bad Blocks
Information
Description
Collisions
Counter of packet collisions when two network
devices transmit at the same time.
FIFO errors
Counter of DMA (Direct Memory Access)
transfer errors when loading the FIFO (First In
First Out buffer) on the Network IC.
Carrier errors
Window errors
Counter of errors from the data carrier signal
due to being outside the limits or lost during
transfer.
Counter of times the Network IC runs out of
FIFO space.
Overflow errors Counter of times the Network IC runs out of
FIFO space.
Length errors
Counter of packets less than 64bytes or greater
than 1518bytes.
CRC errors
Counter of packets with bad CRC (cyclic
redundancy check); count increases when a
packet containing corrupt data is received.
Frame errors
Counter of frame alignment errors caused by a
frame without the correct number of bytes, but
still within the length limit.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Bosch GUI
EN 26
7.11 Problems
This page summarizes any problems encountered by
the DVAS. In normal circumstances, this page should
be empty.
Figure 26 DVAS Problems
7.12 Key
The key is a legend of all symbols used in the Bosch
web interface.
7.13 Event Log
This page displays controller events (disk information,
RAID status changes, power supply status changes,
network events, etc.).
Events are placed in chronological order, newest first.
The event log can be saved as text by highlighting,
copying, and pasting into notepad, or by clicking
Download Event Log and Config Dump on the
event log page.
Figure 27 Event Log
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | RAID Menu
EN 27
8
RAID MENU
This page is used to create or alter settings related to
the RAID array. To access the RAID page, click
RAID, on the left-hand side of the main screen.
8.1 Add Array
To create RAID arrays, from the Add Array tab, select
the drive(s) to be used by clicking the appropriate
check box(es). Arrays can only be built when there are
at least three disks. Disks allocated as spares cannot be
used without first being deleted.
Figure 28 Configuring an Array
Click Create RAID Set to continue. The RAID set
Select RAID Level
will start to build. Array construction can take several
hours to complete. Monitor the progress via the
Progress tab, by clicking Information, at the left-hand
side of the page. Select the Progress tab to show an
overview of all utilities running on the array.
Allows selection of the RAID level for the array.
Currently, RAID 0, 4, and 5 are available. Most server
applications will work best with RAID 5. RAID 4 is
suitable for lots of sequential transactions, but is not
the ideal choice for server environments. RAID 0 is
for users who need speed, not redundancy.
Stages of Array Mapping:
•
Array construct: Writes RAID stripes to disk.
Select Stripe Size
Stripe size for the array designates the amount of data
written to a single disk, before moving on to the next.
Sequential access benefits from a smaller stripe size,
wheras random access benefits from a larger stripe
size. Bosch DVRs require 64KB.
•
Array verify: Verifies that data can be read from
each block of the array.
Depending on disk capacity, it can take up to six hours
to create a RAID Set.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | RAID Menu
EN 28
8.2 Add Volume
8.3 Expand Volume
To add a volume, you must have an array create free
space available. To create an array, first click the radio
button of the array, from the top of the page.
To expand the capacity of a volume, a volume must
have been created, with free space available before the
beginning of the next volume. If you only have a
volume with free space, this is acceptable.
Figure 30 Expanding a Volume
Figure 29 Creating a Volume
Enter the amount of MB to expand the volume by.
Click Expand Volume to advance to the confirmation
page. Select the check box, then click Confirm
Expand Command to continue.
Once the array has been selected, scroll to view the
amount of space available for each array. With this
knowledge, use the following information to define
the volume parameters.
8.4 Delete Volume
Enter the Name for the New Volume
Deleting a volume destroys all data on the volume.
Use this command only if you are sure you wish to
delete this information.
Enter the Size of the New Volume in
Megabytes (MB)
Defines the size of the new volume in Megabytes.
Reserve an Optional Free Space Area at
Beginning of the New Volume for Future
Expansion of a Previous Volume
Defines the amount of free space to be reserved
for expansion of the previous volume.
Select Logical Unit Number (LUN) for New
Volume on Host 0/1
Figure 31 Deleting a Volume
Defines the LUN for each volume on either or
both Host Channels. Use the drop down menu
to select each LUN.
Check the box of the volume to be deleted, then click
Delete Volume to continue. Confirm by selecting the
check box, then click Confirm Delete Command.
A specified LUN can only be accessed by one DVR.
To confirm your choices click Create Volume.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | RAID Menu
EN 29
8.5 Map Volume
Although this page is functional, it is recommended to use the Quick Config page.
To be accessed, each volume must be mapped to a LUN on at least one host channel. If you failed to map a
volume when it was created, or want to change the mapping, use this page.
Figure 32 Mapping Logical Volumes
Use the drop down menus for each volume to select the LUN for each Host Channel. A maximum of eight
LUNS can be applied per channel. Selecting UNMAPPED causes inaccessibility of the selected LUN over that
channel. Click Save Settings to confirm changes.
Changes are made immediately, so changing the LUN of a volume already in use could create a problem with the DVR.
8.6 Rename Volume
This page is used to supply a user-friendly name for a volume.
Figure 33 Renaming a Volume
To change the name of a volume, simply type the new name into the text box and click Save Settings to
continue.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | RAID Menu
EN 30
8.7 Rename Array
Use the Rename Array tab to change the user-defined
name of each configured array.
To rename an array, enter the new name of the array
in the text box and click Save Settings.
Figure 36 Adding a Hot Spare
The two types of hot spares are pool spares and
dedicated spares. Pool spares can be used to rebuild
any array in the event of a disk failure. A dedicated
spare is only used to rebuild the array that it is
dedicated to.
Figure 34 Renaming an Array
To add a pool spare, click the radio button adjacent to
the text Add a pool (floating) hot spare disk, then scroll
down and click the tick button of the unused disk to be
added as a spare. Click Add Hot Spare.
8.8 Delete Array
Use the Delete Array tab to delete an entire array. This
feature (and others) can be disabled via the GUI Mode
tab of the System Settings menu. An array can only be
deleted when all volumes configured on it have been
deleted.
To add a dedicated spare, click the radio button
adjacent to the text Add a hot spare disk dedicated to an
array. Click the radio button of the array to add a
dedicated spare to, then scroll down and click the tick
button of the unused disk to be added as a spare. Click
Add Hot Spare.
8.10 Delete Spare
Use the Delete Spare tab to change the status of the
drive from spare to unused.
Figure 35 Deleting a RAID Array
To delete an array, click the radio button of the array
to be deleted, then click Delete RAID Array. Note
that only one array can be deleted at a time.
When prompted, confirm the deletion by clicking the
tick box in the center of the screen, then click
Confirm Delete Command. To cancel, click Cancel
Delete.
8.9 Add Spare
Use the Add Spare tab to configure a hot spare, which is
a disk used to rebuild data when a RAID disk fails.
Figure 37 Deleting a Hot Spare
To delete the spare status of a drive, click the check
box associated with the spare drive. Once the desired
drive(s) have been selected, click Delete Hot Spare.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | System Menu
EN 31
9.2 Network Settings
9
SYSTEM MENU
The Net Settings tab permits alteration of the properties
of the DVAS Series disk array’s network connection.
Enter any new settings into the text boxes on the right-
hand side of the page, then click Save Configuration
to apply them.
The System Menu page permits access to the pages that
define the DVAS Series disk array connection to the
network.
9.1 SCSI Settings
Quick Configuration automatically configures these
settings.
Refer to the applicable DVR manual for
recommended SCSI settings.
Use this page to alter the behavior of the SCSI Host
Channels.
Figure 39 Configuring Network Settings
How to Set IP Address
Use the radio buttons to select either DHCP (Dynamic
Host Configuration Protocol), or to manually set IP
address. If DHCP is chosen, no further values are required.
IP Address
If manually setting up the network, enter a free IP
address into the text box. The current IP address may
be acceptable.
Figure 38 Configuring SCSI
SCSI ID
Subnet Mask
Allows alteration of the SCSI ID of the DVAS array.
For most operating systems, the default SCSI ID of
0 is fine. All SCSI IDs on a bus must be different, so
ensure that the selected ID does not conflict with
another device ID on the bus. Use the pull down
menu to choose the desired ID.
Set the subnet mask that fits your network class. In
most cases, 255.255.255.0 is fine. Enter the new subnet
mask into the text box.
Gateway
Enter the IP address of your Internet gateway into this
text box.
Termination
By default, termination is set to AUTOMATIC, to
automatically determine whether termination is
required.
Primary/Secondary DNS
Enter the IP address of both your Primary and
Secondary DNS into the text boxes.
SCSI Max Transfer Rate
Web Page Auto Refresh
Defines the maximum speed of the SCSI bus. The
default setting is Ultra2. Click Save Settings to save
these settings.
Identifies whether the web pages should be reloaded
at a selected interval to show any system changes on-
screen. Check Enabled to use this function and specify
a value (in seconds) for frequency of web page
refreshing.
To apply the new Network and SCSI setting, cycle
power to the unit.
When all settings have been updated, click Save
Configuration. Restart the system so the changes take
effect.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | System Menu
EN 32
9.3 Network Port
9.4 E-Alert
Use this page to alter the speed and duplex mode of
The DVAS Series disk array has the capability of
sending an e-mail to a specified e-mail address, in the
event of a warning or error condition.
the Network port.
The DVAS Series disk array has a 10/100Base-T
Ethernet port that can be used in various modes. Use
the drop down menu to select the required mode.
In warning conditions, the DVAS Series disk array
operation continues as normal, but an event has
occurred, indicating potential future difficulties.
Examples are:
Mode Selections are:
•
Higher than normal internal temperature
•
Network IP address change dictated by a
DHCP server (you need to use a new network
address to access the Web Monitor)
Figure 40 Network Port Settings
•
•
Auto negotiate network speed and duplex
Error conditions denote events that significantly reduce
the security of the system. Examples are:
Auto negotiate network speed with fixed full
duplex
•
Failure of a data disk
•
Loss of data due to errors on matching parts of
two or more disks
•
Auto negotiate network speed with fixed half
duplex
•
Failure of a power supply
•
•
•
•
Fixed to 100Megabits Full Duplex
Fixed to 100Megabits Half Duplex
Fixed to 10Megabits Full Duplex
Fixed to 10Megabits Half Duplex
If the DVAS Series disk array is connected to a switch,
you may use full duplex. Half duplex will work
properly with hubs and switches, but may run a little
slower. Only use 100Megabits if you are sure you have
100Megabits networking. If unsure about your
network, use Fixed to 10Megabits Half Duplex.
Figure 41 E-Alert Settings
Click Save Network Port Setting when finished.
To enable the settings, restart the DVAS Series disk
array.
Sender E-mail Address
This is the e-mail address assumed by the DVAS Series
disk array.
SMTP E-mail Address
This is the address or name of your mail server. If
DNS is correctly set up, enter the name of your mail
server either manually or via DHCP.
Recipient E-mail Address
Enter an e-mail address for the DVAS to send e-mail
to; typically the address of an administrator.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | System Menu
EN 33
ATA RAID System-friendly Name
Time Server IP address for auto time and date
This aids in determining the location of a DVAS Series
disk array that has sent e-mail. This feature is useful for
users with many systems, and is a friendly name
relating to the location or use of the unit.
configure allows selection of a time server manually,
or from the preconfigured list.
Time Server time and date format. Select via drop
down box.
When to Send
Indicates the circumstances causing an e-mail to be
sent. The possible options are:
Set system time and date by the time server every
24 hours defines whether the time server is updated
daily.
•
Don’t Send E-mail Alarms
This setting is only recommended for users who do
not wish to receive any e-mails from the unit. Only
an audible alarm will occur in case of a problem.
Once all settings have been entered, click Save
Settings to apply them.
•
•
Send E-mail Alarms for Errors Only
This setting is suitable for most users.
9.6 Security
WARNING: Resetting the factory defaults also resets
the password to the factory default, PASSWORD,
which should be changed immediately to a secure
password.
Send E-mail Alarms for Warnings and Errors
This setting is ideal for expert users. Use the
drop down menu to choose the desired option.
•
E-alert Settings
Send automatic status e-mails. Set to either
Enabled or Disabled.
The DVAS offers two levels of menu security; User and
Administrator. The USER account allows browsing of
many of the information pages and verification of
general product status. ADMIN access allows
alteration of settings and entry to boot mode. By
default, the password login for ADMIN is turned on.
The default passwords for USER and ADMIN are
PASSWORD. Default passwords and usernames must
be entered in UPPERCASE.
Click Save E-alert Settings to confirm the new
settings. Reload this page and use Send Test E-mail
Now to verify that the configuration works.
9.5 Date and Time
It is important to correctly set the subsystem’s date and
time. E-mails sent from a DVAS Series disk array are
time stamped. To accurately gauge the time of an
event, the time/date must be correct.
WARNING: The DVAS should be connected only to
secure networks. To guard against accidental or malicious
tampering of the DVAS, the ADMIN password should
be set to something impossible to guess.
Figure 42 Time and Date Configuration
Enter the date and time in the following format:
Date: dd/mm/yyyy
Time: hh:mm:ss
Figure 43 Password Configuration
Time zone: (relative to GMT) via the drop down
menu.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | System Menu
EN 34
Available Information:
Desired Write Cache State
Use these radio buttons to select the preferred write
cache state; Enabled or Disabled.
Information
Description
Current ADMIN /
USER Login Password
Requirement
Displays whether security is enabled.
Allow SCSI Host to Override Write Cache
Configuration
Some SCSI commands force write cache not to be
used. Check the box to override this.
Change ADMIN /
USER Login Password
Requirement to
Use the radio buttons to select the
security mode for either ADMIN or
USER.
Login User Name is
Fixed to
Both USER and ADMIN user names are
fixed (cannot be altered).
Once the required changes have been made, click
Save Settings to continue.
Password
Type the new password in the text box.
Number of host writes.
Write
Confirm Password
9.8 System Administration
When the new USER / ADMIN settings have been
entered, press the relevant Set ____ Password button.
Only alter one user at a time.
The ADMIN tab allows muting and resounding of the
audible alarm when there is a problem, and clearing
events that require manual responses from the
problem page.
9.7 Cache Settings
DVAS Series disk array has a write cache memory,
which is normally enabled. The cache memory holds
data being written to disk, enabling the controller to
confirm that a command is complete before data is
physically written. A battery backup protects cached
data for up to three days in the event of a power
failure during an unfinished write operation. The
DVAS Series disk array controller automatically
completes any unfinished write operations once power
has been restored, provided the cached data is
available.
Figure 45 System Administration
•
Silence the Audible Alarm
Click this button to silence the audible alarm. If
this does not solve the problem that caused the
alarm to sound, click the red X at the top right
of the window to examine the Problems page.
•
•
Re-sound the Audible Alarm
Click this button to restart the alarm if there is a
fault present.
Figure 44 Cache Configuration
Current Write Cache State
Shows how cache is currently being used.
Acknowledge Lost Data Warning
When the RAID controller cannot reconstruct
array data due to lack of access to the
redundant data (two or more blocks not
accessible, or two disks failed), the following
warning displays: The RAID controller has found
some unrecoverable data blocks. To clear this
warning, click Acknowledge Lost Data
Warning. For information regarding bad blocks,
click Bad Blocks.
Manually Override Current Write Cache Status
Check this box to force the cache on or off without
rebooting.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | System Menu
EN 35
•
Set Rebuild Priority
•
Reboot Controller
Use this setting to increase the amount of IO
time dedicated to rebuilding a critical array. If
host activity is high, a higher rebuild priority
may be needed so the array rebuild completes
in a shorter time period.
Click Reboot Controller to reboot the ATA
RAID controller. While rebooting, configured
arrays and volumes are not accessible from the
attached host system(s). Before using this
function, it is advised to cease all host IO. It
may also be necessary to reboot the host
system(s) once the RAID controller has
rebooted.
•
Set Verify Utility
Set either Surface Scanning or Parity Scrub for
the next array verify utility, once the utility
interval has expired. Surface Scanning uses very
little array IO time, whereas Parity Scrub uses
much more. Surface scanning ensures that all
data blocks on all array disks are readable.
Parity Scrub reads all array data and ensures
parity (redundant) data is intact. Any parity
inconsistencies will be corrected. Both utilities
will correct (where possible) unreadable blocks,
by using the parity data to rebuild missing data
onto a remapped block.
•
Set Spare Mode
Inserted Disks Automatically used as Hot Spares
Any disk not belonging to a RAID array will be
used as a hot spare/rebuild disk. A hot spare
disk must be at least the same capacity as the
smallest RAID array member.
Inserted disks must be manually configured as
hot spares. No newly inserted disk or existing
unused disk will be used as a rebuild disk. The
disk must first be configured as a hot spare, so it
can be used by a degraded/critical array.
Click Execute Verify Utility NOW to force the
selected array utility to run now.
10
LOG OFF
Terminates browser session. This concludes the
Menu Tree.
•
Set Verify Utility Execute Interval
Use the above settings to set the internal time
between verify cycles, or click Execute verify
utility NOW to start the selected verify utility.
Disable Dangerous Commands
Confirm, and click Disable Dangerous
Commands, to put the GUI into this mode.
In this mode, any configuration commands
that will cause data loss or result in loss of
host communications are not permitted.
Read Only
Confirm and click Read Only, and no
configuration of the ATA RAID system is
permitted.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Additional Information
EN 36
NOTE: Make sure the flange is on the bottom edge.
11
Additional Information
Step 4. Attach left and right front (short) extended
brackets to the outer rail using 2 x 8300045
M4 screws, 2 x 8300045 washers , and
2 x 8300044 nuts for each bracket
(FIGURE 49).
11.1 Required Components
•
(1) Slide Kit and Mounting Hardware
•
(1) Pair Accuride Slide Rails
11.2 Rail Kit Installation
Step 1. Remove inner slide rail as shown in
NOTE: Make sure the flange is on the bottom edge.
FIGURE 46. Press down on latch to release.
Figure 46 Remove Slide Rail
Step 2. Attach inner slide rail to chassis using
3 x 8300047 M4 screws, as shown in
FIGURE 47.
Figure 49 Attach (Short) Extended Brackets
Step 5. Attach outer rail to chassis using 4 x M6 x 12
screws and cage nuts per rail, 2 at each end.
NOTE: When attaching the extended brackets, first
attach them loosely. Adjust the length to fit the cabinet,
and then tighten.
Step 6. Slide chassis into outer rail, carefully making
sure the chassis is level with the slide as in
FIGURE 50 (it’s easier if the drives and
power supplies are removed).
Figure 47 Attach Rail to Chassis
Step 3. Attach left and right rear (long) extended
brackets to the outer rail using 2 x 8300045
M4 screws, 2 x 8300045 washers, and
2 x 8300044 nuts for each bracket
(FIGURE 48).
Figure 50 Attach Outer Rail and Slide Chassis in
Figure 48 Attach (Long) Extended Brackets
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Technical Specifications
EN 37
12
DVAS Series Disk Array
Technical Specifications
Physical Specifications
Information
Height
Description
132mm [5.16in] 3U
483mm [18.87in]
521mm [20.35in]
Width
Depth
Depth Including power 537mm [20.98in]
supply handles
Approximate weight
32kg (including drives + packaging)
Power and Cooling
Information
Description
Power Supplies
Cooling
1 x 450W or 2 x 450W load sharing
2 x Radial blowers in power supplies and
one blower in each controller
Communication
Information
Interface
Description
10/100 Base-T Ethernet RJ-45
Protocols
TCP/IP, HTTP, SMTP and FTP
GUI HTML, supports most standard
Internet browsers
E-mail sent via SMTP at failure or warning
event
Data Interfaces
Information
Description
Hard Disk Interface
ATA/100 (14 channels)
Host Channel Interface Ultra 160 SCSI (two channels)
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Instruction Manual | Troubleshooting
EN 38
13
Troubleshooting
Web Interface Problems
Solution
Problem
Nothing happens when I type
the assigned DVAS IP
address into my web browser.
•
•
Verify that the system is responding.
Verify that the IP address is saved, and you can connect to the DVAS. The best way to establish communication with the DVAS
Series disk array is by using a ping utility. Different operating systems have different ping utilities, but they are all very similar.
®
Microsoft will be used for the purpose of this guide.
Open a DOS window and retreat to the root level of the C drive (or the drive containing the Operating System). To do this, type
the following: cd \
C:/> ping 192.1.168.225
(Replace the above IP address with that of the DVAS Series disk array.)
If the ping is successful, a response similar to the one below will be generated.
Reply from 192.168.1.225: bytes=32 time=10ms TTL=30
Reply from 192.168.1.225: bytes=32 time<10ms TTL=30
Ping statistics for 192.168.1.225:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milliseconds:
Minimum = 0ms, Maximum = 10ms, Average = 2ms
If you have a successful reply, but cannot access the home page, consult technical support.
If no reply is returned, verify that the IP address is correct. If using DHCP, verify that DHCP has allocated an address to the unit.
When using the menus I am
prompted to provide a user
name and password.
•
•
This indicates that security is turned on. The user name ADMIN and password PASSWORD (both uppercase) permits access to
any page, unless the password has been changed.
The default user name and
password are not responding.
The login is case sensitive; both username and password are in UPPERCASE. If still unable to login, the user name and
password may have been changed from the factory settings. To cancel this, the unit must be returned to its factory settings.
Restoring factory settings will not harm your data.
•
To restore the factory settings, follow the instructions below. If only resetting the IP address, skip Steps 8 and 9.
1. Make a note of the product’s serial number, as it will be needed later.
2. Turn off the system.
3. Turn power back on while depressing the alarm silence button for more than ten seconds, then release.
4. Depress the button again.
5. The exclamation light should now flash red.
6. Release the button for two seconds and depress it again.
7. After a few seconds the power light will flash red.
8. Release the button for two seconds and depress it again.
9. After a few seconds, the fan light will flash red.
10. Release the button and cycle power to the unit.
The above steps reset DVAS Series disk array to Gleaning mode, which means that an IP address can be set manually.
1. To set an IP address, access a command line, either in a DOS or UNIX compatible computer that is connected to the same
network as the DVAS Series disk array.
2. You must first add an entry to the ARP (Address Resolution Protocol) table of this computer. The entry should be the desired
IP address of the DVAS Series disk array, followed by the MAC address (serial number).
Example: If the MAC address of the DVAS is 00:04:02:D0:00:FD, and the required IP address is 192.168.1.201, you would
type the following at either a DOS prompt, or a UNIX console: arp -s 192.168.1.201 00-04-02-d0-00-fd
arp /a
3. The current ARP table will be displayed. Ensure that the DVAS has been added. Ping the IP address you have specified, as
in: ping 192.168.1.201
4. When the DVAS Series disk array receives the first packet, it will set the IP address that it has received. This means that the
first few packets should timeout. It may take up to thirty seconds for the IP address to be saved. It is not necessary to reboot
the DVAS for the IP address to take effect.
NOTE: This only saves the IP address, not other important settings such as the subnet mask, gateway, and DNS server
addresses. It is important to alter these settings via the GUI interface.
The passwords and security should now be set to the default.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Troubleshooting
EN 39
Start-up Problems
Solution
Problem
The system beeps at power
up.
•
•
Beeping does not mean that the unit is broken. If e-mail is enabled, check the inbox. This will likely provide a clear explanation of
the problem.
Current problems can also be found via the GUI interface; click the red X in top right-hand corner of the home page, or check the
lights on the unit.
LED/Icon
Indication
Power Icon
•
•
Normally Green.
If Red, verify that both power supplies have power, and are switched on. If a power supply has failed, the LED on the power
supply will not be illuminated, although the blower should still be powered from the surviving power supply.
Fan LED
•
•
Normally Green.
If Red, one or more blowers have failed. There are two blowers in the rear of the unit. The two power supplies have embedded
blowers. It is possible for the blower to fail, and the power supply continues to work. This will not be apparent by looking at the
LED. You can Determine if the blower has failed via the web GUI.
Exclaimation Mark LED
Disk Drive LEDs
•
•
Normally Green.
If Red, the RAID controller has failed, or has a problem. This does not necessarily mean that the controller must be replaced. This
LED may indicate other faults, such as missing disks or battery errors. Use the web interface to discover the exact nature of the
problem.
•
•
During activity, the Green LED(s) will flicker (on the front panel, corresponding to the disk drive(s).
If a failure occurs, the LED in the shape of an exclamation mark will illuminate in Amber.
Resolving Problems
The Bosch Interface indicates
that a disk has failed, and my
data is still online.
•
Determine which disk has failed by its Amber exclamation mark on the front LED panel. Extract the faulty disk and insert a
blanking panel into its slot.
•
Contact the dealer to obtain a replacement as soon as possible, as the array may be in a critical state. When the replacement
module arrives, verify that no damage has occurred during transit. Insert the new disk into the empty slot. The DVAS Series disk
array will detect the new disk, and rebuild to it if the array is critical. If you already had a spare disk, the DVAS Series disk array
will assign the new disk as a spare too.
A power supply has failed, but
the system is still operational.
•
Do not remove the faulty power supply! If a power supply fails, the surviving power supply will continue to power the blower in the
failed power supply. Removing a power supply drastically reduces airflow in the chassis. Contact your dealer regarding a
replacement power supply (ACCPS). Only remove the failed power supply when the replacement arrives.
The RAID controller has failed.
•
•
If a RAID controller fails, the data is inaccessible. Your data is safe on the disks until a replacement controller arrives. Data in write
cache will be lost if a controller fails.
Leave the controller in place.
Contact your dealer for assistance with other inquiries.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Firmware Update
EN 40
DO NOT switch the DVAS Series disk array off until
the Microcode Updated OK message is posted at the top
of the event log. If the web interface is not accessible,
wait at least ten minutes before switching the DVAS
Series disk array off.
14
Firmware Update Instructions
The DVAS Series disk array is controlled by firmware
that resides in the controller flash memory (ROM).
Upgrades to provide improved operation capabilities
may be issued by Bosch from time to time, in the form
of e-mail or similar means.
Here are some example messages from the controller’s
event log BEFORE the firmware update completes.
The firmware file is downloaded to the DVAS Series
disk array via FTP (file transfer protocol), and can be
downloaded from any computer that supports FTP, on
the same network as the DVAS Series disk array.
Microsoft Windows® 98/NT/2000 and Unix systems,
for example, support FTP, which is conventionally
activated from a command line (MS-DOS window in
NT systems). Due to the DVAS Series disk array FTP
restrictions, we recommend this method be used for
security and memory space reasons.
0036: 0055R, 0000-00:10:10: Microcode Updated OK
0037: 0055R, 0000-00:08:08: Microcode extents, Start
Addr 0x10000, End Addr 0x148938
0038: 0055R, 0000-00:08:08: Microcode S-record file
verified OK
0039: 0055R, 0000-00:08:05: Starting microcode
update
Remember - DO NOT switch the DVAS Series disk
array off until Microcode Updated OK appears in the
event log shown above. The controller event log is
stored on disk, so at least one disk must be installed in
the DVAS Series disk array for the firmware update to
proceed.
Downloading does not affect the operation of the
DVAS Series disk array, and can be carried out at any
convenient time during system operation. It is
recommended that the host system be shut down to
cease RAID array read/write activity. A DVAS Series
disk array restart is required to activate the new
firmware. Verify the firmware version by accessing the
Information MENU > HARDWARE, via the web user
interface.
Controller Update Procedure
To begin the controller firmware update, first copy the
new firmware file from Bosch, onto the machine where
you intend to run FTP.
Before actually beginning the firmware update, READ
the following carefully. If these instructions are not
followed, the DVAS Series disk array may be rendered
unusable and the RAID array will not be available to
the host computer system.
1. In a command line window, go to the directory
(folder) where the firmware resides, and type:
ftp <IP address>
When prompted for a user name, type ADMIN
in upper case. The password is required (if not
changed, the default password is PASSWORD).
DO NOT switch the DVAS Series disk array off
during a firmware update process. This will likely
render the DVAS Series disk array unusable.
2. Now type:
If unsure about the state of the firmware update, wait
at least ten minutes (from the start of sending the new
firmware), for the update to complete.
put <filename>
where the filename is the name of the update file
supplied by Bosch.
Wait five minutes before accessing the event log. Do
not continually click the event log link, as it is a large
web page that will slow down the firmware update
process. It is recommended that you access the event
log every 30 seconds or so after the initial five
minutes.
You may have to change the local directory from within
FTP if you are not already in the directory of the new
firmware file. To do this, use a command such as:
lcd <newfirmwarefilepath>
(local change directory to the location of the new
firmware file).
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Firmware Update
EN 41
3. The download process includes storing the data
on the DVAS Series disk array, and will take
five to ten minutes. When the update has
finished, a message Transfer OK. firmware update
successful should appear.
4. Confirm that the update has succeeded by
entering the Web Monitor, and selecting the
Event Log page in user mode. The message,
Microcode Updated OK should be visible near the
top of the log.
5. The new firmware will take effect at the next
DVAS Series disk array power up.
Windows 98 timeout
If this procedure is followed on Windows 98 systems
(and possibly other systems), the FTP process in
Windows 98 will time out during Step 3. This occurs
after all data has been transferred to the DVAS Series
disk array, but before the storage process (flash update)
is complete. In this case, the Transfer OK message will
not appear, although the download should have
completed successfully.
After at least five minutes from the start of Step 2,
check the log to ensure that the update has been
successful. If so, the update will take effect at the next
restart (Step 5).
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual | Appendix A
EN 42
Hard Drive Assemblies
Appendix A
Servicing Removable Components
Disk drives are sensitive to static electricity and
physical shock. Observe proper ESD
precautions and handle with care.
Power Supply Unit (PSU)
Insertion
Insertion
Pull the handle of the PSU so it is at 90° to the main
PSU unit. Line up the PSU with the guide rails on the
DVAS. Insert the PSU gently until it comes to a halt,
then close the handle and secure it in place with the
screw (included).
Line the disk carrier up to an available disk slot. Be
sure the handle is open, and the carrier push button is
toward the bottom of the chassis. Push the disk carrier
in until it is fully inserted. Close the handle and push
in the carrier button to secure it in place.
Removal
Removal
Turn off the power switch. Disconnect the power cord,
loosening the cable clamp if necessary. Loosen the
screw on the power supply by turning it counter-
clockwise. Pull out the handle of the PSU so that is 90°
to the chassis. While supporting the weight of the PSU,
use the handle to pull the power supply free from the
chassis.
Removing a disk while in operation within a RAID set
will cause the RAID set to degrade. Only remove a
disk which has been marked as bad by the GUI, with
an Amber LED illuminated beneath it. To remove a
disk, push the button on the disk carrier to release the
handle. Gently pull the bottom of the handle toward
you and wait ten seconds for the disk to stop spinning.
Continue sliding the disk out of the chassis.
If your DVAS has the dual redundant power supply
option, a faulty power supply may be removed and
replaced while the unit is operational. Only remove a
power supply from a working unit if it is faulty and a
replacement is on-site. Removing a PSU when no
replacement is immediately available may result in
overheating and shutdown. Ensure that the correct
PSU is removed; the faulty power supply will not have
a green status LED illuminated on its rear panel.
RAID Controller
Insertion
A RAID controller should not be inserted while the
unit is powered on. If exchanging a faulty RAID
controller, schedule a shutdown before replacing it.
Insert the RAID controller into its slot, ensuring that
the metal runners line up with the internal guides.
Firmly push the RAID controller fully into the chassis
until the side clips click into place.
Removal
Do not remove a faulty controller while power is on;
power must be disconnected.
Push the side clips securing the controller inwards
(toward each other). While supporting the weight of
the unit, use the handles to pull the controller free
from the unit.
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
|
DVAS | Instruction Manual |
EN 43
Bosch Security Systems | 20 January 2004
Download from Www.Somanuals.com. All Manuals Search And Download.
Bosch Security Systems, Inc.
850 Greenfield Road
Robert Bosch GmbH
Geschäftsbereich
Bosch Security Systems B.V.
P.O. Box 80002
Lancaster, PA 17601 EE.UU.
Tel: 800-326-3270
Postfach 10 60 50
70049 Stuttgart
5600 JB Eindhoven
The Netherlands
Fax: 1-717-735-6560
Telefax (0711) 811-12 34
Tele +31 40 27 80000
© 2004 Bosch Security Systems GmbH
3935 890 43112 04-04 | January 20, 2004 | Data subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|