Acer Projector
P7270/P7270i/P7280/P7280i Series
User's Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•
•
•
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
•
•
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
•
•
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
•
•
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, type
SPT-2, rated 7A 125V minimum, VDE approved or its equivalent, 4.6 meters
(15 feet) maximum length.
Download from Www.Somanuals.com. All Manuals Search And Download.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
•
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
•
•
Turn on the projector first and then signal sources
Do not place the product in following environments:
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
•
•
•
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
•
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
Download from Www.Somanuals.com. All Manuals Search And Download.
vi
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
•
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
•
•
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, sugges to ensure the projector
completes its cooling cycle before disconnecting power.
•
Do not turn off the main power abruptly or unplug the projector during
operation. It can lead to lamp breakage, fire, electric shock or other
trouble. The best way is to wait for the fan to turn off before turning main
power off.
•
•
Do not touch air outlet grille and bottom plate which becomes hot.
Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
•
•
•
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the projector or remote controller.
•
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
•
•
•
•
•
•
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
•
•
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
Download from Www.Somanuals.com. All Manuals Search And Download.
vii
Operating environment for using wireless function
(Optional)
Warning! For safety reasons, turn off all wireless or radio transmitting
devices when using your machine under the following conditions. These
devices may include, but are not limited to: wireless LAN (WLAN), Bluetooth
and/or 3G.
Remember to follow any special regulations in force in any area, and always
switch off your device when its use is prohibited or when it may cause
interference or danger. Use the device only in its normal operating positions.
This device meets RF exposure guidelines when used normally, and it and its
antenna are positioned at least 1.5 centimeters (5/8 inches) away from your
body. It should not contain metal and you should position the device the above-
stated distance from your body.
To successfully transmit data files or messages, this device requires a good
quality connection to the network. In some cases, transmission of data files or
messages may be delayed until such a connection is available.
Ensure that the above separation distance instructions are followed until the
transmission is completed.
Parts of the device are magnetic. Metallic materials may be attracted to the
device, and persons with hearing aids should not hold the device to the ear with
the hearing aid. Do not place credit cards or other magnetic storage media near
the device, because information stored on them may be erased.
Medical devices
Operation of any radio transmitting equipment, including wireless phones, may
interfere with the functionality of inadequately protected medical devices.
Consult a physician or the manufacturer of the medical device to determine if
they are adequately shielded from external RF energy or if you have any
questions. Switch off your device in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health care facilities
may be using equipment that could be sensitive to external RF transmissions.
Pacemakers. Pacemaker manufacturers recommend that a minimum separation
of 15.3 centimeters (6 inches) be maintained between wireless devices and a
pacemaker to avoid potential interference with the pacemaker. These
recommendations are consistent with the independent research by and
recommendations of Wireless Technology Research. Persons with pacemakers
should do the following:
•
Always keep the device more than 15.3 centimeters (6 inches) from the
pacemaker.
•
Not carry the device near your pacemaker when the device is switched on.
If you suspect interference, switch off your device, and move it.
Download from Www.Somanuals.com. All Manuals Search And Download.
viii
Hearing aids. Some digital wireless devices may interfere with some hearing
aids. If interference occurs, consult your service provider.
Vehicles
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles such as electronic fuel injection systems, electronic
antiskid (antilock) braking systems, electronic speed control systems, and air bag
systems. For more information, check with the manufacturer, or its
representative, of your vehicle or any equipment that has been added. Only
qualified personnel should service the device, or install the device in a vehicle.
Faulty installation or service may be dangerous and may invalidate any
warranty that may apply to the device. Check regularly that all wireless
equipment in your vehicle is mounted and operating properly. Do not store or
carry flammable liquids, gases, or explosive materials in the same compartment
as the device, its parts, or enhancements. For vehicles equipped with an air bag,
remember that air bags inflate with great force. Do not place objects, including
installed or portable wireless equipment in the area over the air bag or in the
air bag deployment area. If in-vehicle wireless equipment is improperly
installed, and the air bag inflates, serious injury could result.
Using your device while flying in aircraft is prohibited. Switch off your device
before boarding an aircraft. The use of wireless teledevices in an aircraft may be
dangerous to the operation of the aircraft, disrupt the wireless telephone
network, and may be illegal.
Potentially explosive environments
Switch off your device when in any area with a potentially explosive
atmosphere and obey all signs and instructions. Potentially explosive
atmospheres include areas where you would normally be advised to turn off
your vehicle engine. Sparks in such areas could cause an explosion or fire
resulting in bodily injury or even death. Switch off the device at refueling points
such as near gas pumps at service stations. Observe restrictions on the use of
radio equipment in fuel depots, storage, and distribution areas; chemical plants;
or where blasting operations are in progress. Areas with a potentially explosive
atmosphere are often, but not always, clearly marked. They include below deck
on boats, chemical transfer or storage facilities, vehicles using liquefied
petroleum gas (such as propane or butane), and areas where the air contains
chemicals or particles such as grain, dust or metal powders.
Caution for Listening
To protect your hearing, follow these instructions.
•
•
•
•
•
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Download from Www.Somanuals.com. All Manuals Search And Download.
ix
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit http://global.acer.com/about/
sustainability.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
information, check www.lamprecycle.org
Download from Www.Somanuals.com. All Manuals Search And Download.
x
First things first
Usage Notes
Do:
•
•
Turn off the product before cleaning.
Use a soft cloth moistened with mild detergent to clean the display
housing.
•
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•
•
•
Block the slots and openings on the unit provided for ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
•
•
•
•
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•
•
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•
•
Please do not open or disassemble the product as this may cause electric shock.
When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
•
•
•
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•
•
•
Turn on the projector first and then the signal sources.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Download from Www.Somanuals.com. All Manuals Search And Download.
4
8
10
How to get a preferred image size by adjusting
21
23
25
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Compatibility modes
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Introduction
Product Features
This product is a single-chip DLP® projector. Outstanding features include:
•
•
DLP® technology
Native 1024 x 768 XGA resolution
4:3 / 16:9 aspect ratio supported
•
Acer ColorBoost technology delivers nature’s true colors for vivid, life-like
images
•
•
High brightness and contrast ratio
Versatile display modes (Bright, Standard, Video, Blackboard, User 1, User
2) enable optimum performance in any situation
•
•
•
•
NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
Top-loading lamp design allows easy lamp replacement
Lower power consumption and economy (ECO) mode extends lamp life
Empowering Key reveals Acer Empowering Technology utilities (Acer
eView, eTimer, eOpening Management) for easy adjustment of settings
•
•
•
•
•
•
Equipped with DVI and HDMITM connections supporting HDCP
Advanced digital keystone correction optimizes presentations
Multi-language onscreen display (OSD) menus
Full-function remote control
Manual focus projection lens zooms up to 1.2x
8x digital zoom and pan move function
•
Microsoft® Windows® 2000, XP, Vista® OS compliant
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Package Overview
This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.
Projector with lens cap
Compostive video cable
S-Video cable
Power cord
DVI-D cable
Carrying case
VGA cable
3 RCA component cable
Security card
Acer Projector
Quick Start Guide
2 x User's Guide (Wireless CD
for P7270i/P7280i Series)
Remote control
2 x Quick start guide
(Wireless Quick Start Guide
for P7270i/P7280i Series )
2 x Batteries
2 x Dust filters
Wireless antenna
(P7270i/P7280i series)
Battery Pack with USB PnS
handy drive (P7270i/P7280i
Series)
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Projector Overview
Projector Outlook
Front / upper side
1
6
2
3
4
7
8
5
6
9
#
Description
#
Description
Remote control receiver
Tilt adjusting wheel
Elevator button
1
6
Control panel
Zoom ring
Focus ring
Zoom lens
Lens cap
2
3
4
5
7
8
9
Elevator foot
Rear side
20 21 22 23 24
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
17
18
19
#
Description
#
Description
PC analog signal/HDTV/component
video input connector (VGA IN 2)
Audio input connector (VGA IN 1/DVI-
D/HDMI signal)
1
2
3
13
PC analog signal/HDTV/component
video input connector (VGA IN 1)
14 USB connector
DVI input connector (for digital signal
with HDCP function)
15 RS232 connector
4
5
6
HDMI connector
16 Audio output connector
17 SPDIF output connector
18 Power socket
Top cover release button
TM
Kensington lock port
Download from Www.Somanuals.com. All Manuals Search And Download.
4
#
7
8
Description
#
Description
Horn
19(#) Wired IR remote input connector
20(#) Antenna
YPbPr/YCbCr input connector
Monitor loop-through output
connector (VGA-Out)
9
21(#) Lan (RJ45 Port for 10/100M Ethernet)
10 S-Video input connector
22(#) Audio output connector for wireless
23(#) Reset button
11 Composite video input connector
Audio input connector (VGA IN 2/
12
24(#) Power LED for wireless
Component/S-video/Composite signal)
Note: "*" Only for P7270i/P7280i series.
Control Panel
5
6
1
2
7
3
4
8
9
#
Function
Description
Automatically synchronizes the projector to the
input source.
1
RESYNC
MENU
•
Press "MENU" to launch the Onscreen display
(OSD) menu, back to the previous step for the
OSD menu operation or exit the OSD menu.
Confirm your selection of items.
2
•
3
4
TEMP
LAMP
Temp Indicator LED
Lamp Indicator LED
Use to
select items or make
5
6
Four directional select keys
SOURCE
adjustments to your selection.
Press "SOURCE" to choose RGB, Component, S-
Video, Composite, DVI, HDTV and HDMI™
sources.
7
8
Empowering key
Unique Acer functions: eOpening, eView, eTimer.
Sends signals to the projector.
Infrared transmitter
See the contents in "Turning the Projector On/
Off" section.
9
POWER
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Remote Control Layout
2
1
3
10
4
5
11
12
6
23
14
15
16
7
8
9
17
18
19
25
26
27
28
20
21
22
29
13
24
30
31
#
Icon
Function
Infrared
transmitter
Laser pointer
Description
1
Sends signals to the projector.
2(#)
3
Aim the remote at the viewing screen.
POWER
Refer to the "Turning the Projector On/Off" sec
4
5
6
7
RESYNC
FREEZE
ASPECT RATIO
ZOOM
Automatically synchronizes the projector to the input source.
To pause the screen image.
To choose the desired aspect ratio (Auto/4:3/16:9).
Zooms the projector display in or out.
Left-/right-click buttons are on the left and right, respectively;
the center button works as a multidirectional pointer stick. To
enable this function, an USB cable must be connected to
projector from your PC.
MOUSE Left/
Right Click
8
9
VOLUME
Increases/decreases the volume.
Aim the remote at the viewing screen, press and hold this
button to activate the laser pointer.
10(#)
Laser button
This function is not supported in Japanese market.
Press "SOURCE" to choose from RGB, Component-p,
Component-i, S-Video, Composite, DVI-D, Video and HDTV
sources.
11
SOURCE
Momentarily turns off the video. Press "HIDE" to hide the
image, press again to display the image.
To turn on/off the volume.
12
13
HIDE
MUTE
Download from Www.Somanuals.com. All Manuals Search And Download.
6
#
Icon
Function
Description
•
•
Press "MENU" to launch the Onscreen display (OSD) menu,
back to the previous step for the OSD menu operation or
exit the OSD menu.
14
MENU
Confirm your selection of items.
Four directional Use up, down, left, right buttons to select items or make
select keys
KEYSTONE
LOCATION
adjustments to your selection.
15
Adjusts the image to compensate for distortion caused by
tilting the projector.
16
17
Choose the menu location on the display screen.
For computer mode only. Use this button to select the next or
previous page. This function is only available when connected
to a computer via a USB cable.
PAGE
Empowering
key
COLOR
Unique Acer functions: eOpening, eView, eTimer
18
19
20
Management.
Press "COLOR" to adjust the color temperature of image.
Use the "CONTRAST" option to control the difference
between the lightest and darkest parts of the picture.
CONTRAST
21
22
VIDEO
S-VIDEO
To change source to COMPOSITE VIDEO.
To change source to S-Video.
Press "PIP" to see two screens at the same time. The main
screen projection signal uses VGA input by default while the
smaller PIP display uses a secondary video source.
23
PIP
Press "WIRELESS" to display the image which is wirelessly
transmitted from the PC to the projector via the "Acer
eProjection Management" utility. (for wireless model)
24(*)
WIRELESS
25
26
BRIGHTNESS
RGB
Press "BRIGHTNESS" to adjust the brightness of the image.
Press "RGB" for true-color optimization.
Press "COMPONENT" to change source to Component video.
This connection supports YPbPr (480p/576p/720p/1080i) and
YCbCr (480i/576i).
Press "VGA" to change source to the VGA connector. This
connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
Press "DVI" to change source to DVI. This connection supports
digital RGB, analog RGB, YPbPr (480p/576p/720p/1080i), YCbCr
(480i/576i) and HDCP signals.
27
28
29
COMPONENT
VGA
DVI
30
31
HDMI™
KeyPad 0~9
To change source to HDMI™.
Press "0~9" to input a password in the "Security settings".
Note: "*" Only for P7270i/P7280i series.
"#" Japan area is not supported.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Note:
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Getting Started
Connecting the Projector
Wired Remote
DVD player
VGA, DVI
DVD player,
10
Set-top Box,
HDTV receiver
DVI-D
D-Sub
HDMI
D-Sub
10
2
8
14
9
R
B
5
G
HDTV adapter
D-Sub
R
B
G
HDMI
D-Sub
DVI-D
1
Y
3
B
13
B
6
W
R
12
11
S-Video Output
Video Output
7
RS232
4
USB
RS232
#
Description
#
Description
1 Power cord
2 VGA cable
8 DVI cable
9 HDMI cable
3 Composite video cable
4 USB cable
10 3 RCA component cable
11 RS232 cable
5 VGA to component/HDTV adapter
6 S-Video cable
12 Audio cable Jack/RCA
13 SPDIF cable
7 Audio cable jack/jack
14 Audio cable Jack for wired remote
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Installing the dust filter of the projector
This projector support dust proof function.
Follow these steps:
1
2
3
Take two dust filters from the
accessory bag.
Slide the dust filter in
(Illustration #1)
Insert a suitable coin into the
top cover release button
(Illustration #2) and rotate
clockwise (Illustration #3).
Open the top cover.
4
5
(Illustration #4)
Slide in another dust filter.
(Illustration #5)
6
7
Connect the power cord.
Turn on the projector by
pressing the power cord.
Caution:
1
2
The dust proof is optional function depend on users.
Once you decide to implement the dust proof function, please
ensure that both top and bottom dust filters are properly
installed. Otherwise there will be a warning sound and the
projector can not be turned on.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Turning the Projector On/Off
Turning on the Projector
1
2
Remove the lens cap.(Illustration #1)
Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
3
4
Turn on the projector by pressing "Power" button on the control panel,
and the Power indicator LED will turn blue.(Illustration #2)
Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
•
If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.
•
•
If the screen displays "No Signal", please make sure the signal cables
are securely connected.
If you connect to multiple sources at the same time, use the "Source"
button on either control panel or the remote control or direct source
key on the remote control to switch between inputs.
2
Power button
1
Lens cap
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Turning off the Projector
1
To turn off the projector, press the "Power" button twice. The message
below will display onscreen for 10 seconds.
"Please press power button again to complete the shutdown process."
2
Immediately after powering off, the Power indicator LED will flash RED
rapidly and the fan(s) will continue to operate for about 120 seconds. This
is to ensure that the system cools correctly.
3
4
Once the system has finished cooling, the "Power" indicator LED will turn
solid RED which means projector enter standby mode.
It is now safe to unplug the power cord.
Warning: Do not turn on the projector immediately after
powering off.
Note: If you wish to turn the projector back on, you must wait for
60 seconds at least to press the "Power" button to restart the
projector.
Warning indicators:
•
•
If the projector automatically shuts down and the LAMP indicator
turns solid RED, please contact your local reseller or service center.
If the projector automatically shuts down and the TEMP indicator
turns solid RED, this indicates that the projector has overheated. The
message below will display onscreen if this is about to happen:
"Projector Overheated. Lamp will automatically turn off soon."
•
If the TEMP indicator flashes RED and the message below is displayed
onscreen, please contact your local dealer or service center:
"Fan fail. Lamp will automatically turn off soon."
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Adjusting the Projected Image
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise the image:
1
2
Press the elevator foot release. (Illustration #1)
Raise the image to the desired height angle (Illustration #2), then release
the button to lock the elevator foot into position.
3
Use Tilt adjusting wheel (Illustration #3) to fine-tune the display angle.
To lower the image:
1
2
Press the elevator foot release. (Illustration #1)
Lower the image to the desired height angle (Illustration #2) , then release
the button to lock the elevator foot into position.
3
Use Tilt adjusting wheel (Illustration #3) to fine-tune the display angle.
1
Elevator Button
3
2
Tilt adjusting wheel
Elevator Foot
Download from Www.Somanuals.com. All Manuals Search And Download.
14
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen. Example: If the
projector is 3 m from the screen, good image quality is possible for image sizes
between 78" and 94".
Note: Remind as below figure, the space of 158 cm height is
required when located at 3m distance.
Max screen size
Min screen size
94"
B
78"
Height: 158cm
Form base to
top of image
Height:
131cm
C
A
3m
Desired Distance
Figure: Fixed distance with different zoom and screen size.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Screen size
(Min zoom)
Screen size
(Max zoom)
Top
Top
Desired
Distance
(m)
From base
to top of
image (cm)
<C>
From base to
top of image
(cm)
Diagonal
(inch) W (cm) x H (cm)
<B>
Diagonal
(inch) W (cm) x H (cm)
<B>
<A>
<C>
1.2
1.5
2
31
39
64 x 48
79 x 60
52
38
47
76 x 57
96 x 72
63
65
79
52
106 x 79
132 x 99
159 x 119
185 x 139
212 x 159
238 x 179
265 x 198
317 x 238
370 x 278
423 x 317
476 x 357
87
63
127 x 96
105
131
158
184
210
236
263
315
368
420
473
2.5
3
65
109
131
153
175
196
218
262
306
349
393
78
159 x 119
191 x 143
223 x 167
255 x 191
287 x 215
318 x 239
382 x 287
446 x 334
510 x 382
573 x 430
78
94
3.5
4
91
110
125
141
157
188
219
251
282
104
117
130
156
182
208
234
4.5
5
6
7
8
9
Zoom Ratio: 1.2x
Download from Www.Somanuals.com. All Manuals Search And Download.
16
How to get a preferred image size by adjusting
distance and zoom
A
50"
Desired
image size
D
Height
Form base to
top of image
1.6m
B
1.9m
Desired Distance
C
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring. For example: to obtain an image size of 50" set
the projector at a distance 1.6 m and 1.9 m from the screen and adjust the zoom
level accordingly.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Desired Image Size
Distance (m)
Top (cm)
From base to top of
Diagonal (inch)
Max zoom
Min zoom
<C>
W (cm) x H (cm)
image
<D>
<A>
<B>
***
1.3
1.6
1.9
2.2
2.6
2.9
3.2
3.8
4.8
5.7
6.4
8.0
9.6
31
63 x 47
81 x 61
1.2
1.5
1.9
2.3
2.7
3.1
3.5
3.8
4.6
5.8
6.9
7.7
9.6
***
52
40
67
50
102 x 76
122 x 91
142 x 107
163 x 122
183 x 137
203 x 152
244 x 183
305 x 229
366 x 274
406 x 305
508 x 381
610 x 457
84
60
101
117
134
151
168
201
251
302
335
419
503
70
80
90
100
120
150
180
200
250
300
Zoom Ratio: 1.2x
Download from Www.Somanuals.com. All Manuals Search And Download.
18
User Controls
Acer Empowering Technology
Acer Empowering Key provides three
Empowering Key
Acer unique functions, they are "Acer
eView Management", "Acer eTimer
Management" and "Acer eOpening
Management" respectively. Press "
"
key for more than one second to launch
the Onscreen display main menu to
modify its function.
Acer eView Management
Press " " to launch "Acer eView
Management" submenu.
"Acer eView Management" is for
display mode selection. Please refer to
Onscreen Display Menus section for
more detail.
Acer eTimer Management
Press " " to launch "Acer eTimer
Management" submenu.
"Acer eTimer Management" provides
the reminding function for
presentation time control. Please refer
to Onscreen Display Menus section for
more detail.
Acer eOpening Management
Press " " to launch "Acer eOpening
Management".
"Acer eOpening Management" allows
user to change the Startup screen to
their personalized image. Please refer
to Onscreen Display section for more
detail.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
•
To open the OSD menu, press "MENU" on the remote control or control
panel.
•
When the OSD is displayed, use the
keys to select any item in the
main menu. After selecting the desired main menu item, press
submenu for feature setting.
to enter
•
Use the
keys to select the desired item and adjust the settings by
keys.
using the
•
•
•
Select the next item to be adjusted in the submenu and adjust as described
above.
Press "MENU" on the remote control or control panel, the screen will
return to the main menu.
To exit OSD, press "MENU" on the remote control or control panel again.
The OSD menu will close and the projector will automatically save the new
settings.
Main menu
Setting
Sub menu
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Color setting
There are many factory presets optimized for various types of
images.
Display Mode
•
•
•
•
Bright: For brightness optimization.
Standard: For common environment.
Video: For playing video in a bright environment.
Blackboard: Blackboard mode can improve displayed color
when you project onto darker surfaces.
•
•
User 1: Memorize user’s settings.
User 2: Memorize user’s settings.
Adjust the brightness of the image.
Brightness
Contrast
•
•
Press
Press
to darken image.
to lighten the image.
"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
•
•
Press
Press
to decrease the contrast.
to increase the contrast.
Adjust the color temperature. At higher color temperatures, the
screen looks colder; at lower color temperatures, the screen looks
warmer.
Color
Temperature
Effects the representation of dark scenery. With greater gamma
value, dark scenery will look brighter.
Degamma
Adjusts the red color.
Adjusts the green color.
Adjusts the blue color.
Color R
Color G
Color B
Adjusts a video image from black and white to fully saturated
color.
Saturation
•
•
Press
Press
to decrease the amount of color in the image.
to increase the amount of color in the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Adjusts the color balance of red and green.
Tint
•
•
Press
Press
to increase the amount of green in the image.
to increase the amount of red in the image.
Note: "Saturation" and "Tint" functions are not supported under computer
mode or DVI mode.
Image setting
H Keystone
Press the
or
to adjust image distortion horizontal and makes
to adjust image distortion vertical and makes a
a squarer image.
Press the or
squarer image.
Use this function to choose your desired aspect ratio.
V Keystone
Aspect Ratio
•
•
•
Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
Projection
Front-Desktop
•
The factory default setting.
Front-Ceiling
•
When you select this function, the projector inverts the image for
ceiling-mounted projection.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Rear-Desktop
When you select this function, the projector reverses the image so
you can project from behind a translucent screen.
Rear-Ceiling
•
•
When you select this function, the projector reverses and inverts
the image at same time. You can project from behind a
translucent screen with ceiling mounted projection.
H. Position
(Horizontal
position)
•
•
Press
Press
to move the image left.
to to move the image right.
V. Position
(Vertical position)
•
•
Press
Press
to move the image down.
to move the image up.
Frequency
"Frequency" changes the projector's refresh rate to match the
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
Tracking
Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to
correct it.
Sharpeness
Adjusts the sharpness of the image.
•
•
Press
Press
to decrease the sharpness.
to increase the sharpness.
Signal Type
Select signal type from RGB, YCbCr or YPbPr source.
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under DVI or Video mode.
Note: "Sharpness" functions is not supported under DVI and Computer
mode.
Note: "Signal Type" function is only for HDMI or SCART connector.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Management setting
ECO Mode
Choose "On" to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
Auto Shutdown
Source Lock
The projector will automatically shutdown when there is no signal
input after the allocated time. (in minutes)
When source lock is turned "off", the projector will search for
other signals if the current input signal is lost. When source lock is
turned "on", it will "lock" the current source channel unless you
press "Source" button on the remote control for the next channel.
Menu Location
Startup Screen
Choose the menu location on the display screen.
Use this function to select your desired startup screen. If you
change the setting, the changes will take effect when you exit the
OSD menu.
•
•
Acer: The default startup screen of your Acer projector.
User: Use memorize picture from "Screen Capture" function.
Screen Capture
Use this function to customize the startup screen. To capture the
image that you want to use as the startup screen, follow the
instructions below.
Notice:
Before proceeding with the following steps, make sure that the
"Keystone" is set to the default value 0 and the aspect ratio is set
to 4:3. For details, refer to the "Image Setting" section.
•
Change the "Startup Screen" from the default setting "Acer"
to "User".
•
•
Press "Screen Capture" to customize the startup screen.
A dialog box appears to confirm the action. Choose "Yes" to
use the current image as your customized startup screen. The
capture range is the red rectangular area. Choose "No" to
cancel the screen capture and exit the onscreen display (OSD).
A message appears, stating that the screen capture is in
progress.
When the screen capture is finished, the message disappears
and the original display is shown.
The customized startup screen, as shown below, takes effect
when there is a new input signal or when you restart the
projector.
•
•
•
Note: This screen capture function is limited by 4:3 aspect ratio only.
Note: For XGA models, to get best quality for you desired image, suggest
end-user set PC resolution to 1024 x 768 before you use this function.
Note: For SVGA models, to get best quality for you desired image, suggest
end-user set PC resolution to 800 x 600 before you use this function.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Lamp Hour Elapse
Lamp Reminding
Displays the lamp’s elapsed operating time (in hours).
Activate this function to display a reminder to change the lamp 30
hours before its expected end-of-life.
Lamp Hour Reset
Security
Press the
counter to 0 hours.
button after choosing "Yes" to turn the lamp hour
Security
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press
to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first
before changing the security settings.
•
Select "On" to enable the security function. The user has to
enter a password to operate the projector. Please refer to the
"User Password" section for details.
•
If "Off" is selected, then the user can turn on the projector
without password.
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
•
Press
or
to select the timeout interval.
•
•
The range is from 10 minute to 990 minutes.
When the time is up, the projector will prompt the user to
enter the password again.
•
•
The factory default setting of "Timeout(Min.)" is "Off".
Once the security function is enabled, the projector will
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
User password
•
•
Press
to setup or change the "User Password".
Press number keys to set your password on the remote control
and press "MENU" to confirm.
•
•
Press
to delete character.
Enter the password when you see "Confirm Password"
displayed.
•
•
The password should be between 4 and 8 characters long.
If you select "Request password only after plugging power
cord", the projector will prompt the user to enter the
password every time the power cord is plugged.
•
If you select "Always request password while projector turns
on", the user has to enter the password every time when the
projector is turned on.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•
•
Press
to change the "Administrator Password".
The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to
retrieve the administrator password:
•
An unique 6-digit "Universal Password" which is printed on
the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.
•
If losing this security card and number, please contact with an
Acer service center.
Lock User Startup Screen
•
Default Lock User Startup Screen is "OFF". If lock user startup
screen is "ON", users cannot change startup screen anymore
and avoid other users change that arbitrarily. Choose "OFF"
to unlock startup screen.
Reset
•
•
Press the button after choosing "Yes" to return the
parameters on all menus to the factory default settings.
Wireless
Please refer to wireless booklet for details. (For P7270i/P7280i
series only)
Audio setting
Volume
•
Press
Press
to decrease the volume.
to increase the volume.
•
Mute
•
•
Choose "On" to mute the volume.
Choose "Off" to restore the volume.
Power On/Off Volume
•
Select this function to adjust the notification volume when
turning the projector on/off.
Alarm Volume
•
Select this function to adjust the volume of any warning
notifications.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Timer setting
Timer Start
•
Press
Press
to start or stop the timer.
or to adjust the timer period.
Timer Period
•
Timer Volume
•
Select this function to adjust the notification volume when
the timer function is enabled and time is up.
Timer Display
•
Press
or
to which timer mode to display on the
screen.
Timer Location
•
Choose the location of the timer on the screen.
PIP setting
PIP
•
•
Choose "On" to to see two screens at the same time.
Choose "Off" to disable the function.
PIP Source
Press
and
to choose the secondary video source:
Composite, S-Video or Component signal.
PIP Location
PIP Size
Choose the PIP secondary signal location on the display screen.
Choose the PIP secondary signal size on the display screen.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
#
Problem
Solution
1
No image appears
onscreen
•
•
•
Connected as described in the "Getting Started"
section.
Ensure none of the connector pins are bent or
broken.
Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
•
Make sure you have removed the lens cap and the
projector is switched on.
2
Partial, scrolling
or incorrectly
displayed
image(For PC
(Windows 95/98/
2000/XP))
•
•
Press "RESYNC" on the remote control or control panel.
For an incorrectly displayed image:
•
Open "My Computer," open the "Control
Panel," and then double-click the "Display"
icon.
•
•
Select the "Settings" tab.
Verify that your display resolution setting is
lower than or equal to UXGA (1600 x 1200).
Click the "Advanced Properties" button.
•
If the problem still appears, change the monitor display
you are using and follow the steps below:
•
•
•
Verify that the resolution setting is lower than
or equal to UXGA (1600 x 1200).
Click the "Change" button under the
"Monitor" tab.
Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
•
Verify that the resolution setting of the
monitor display is lower than or equal to UXGA
(1600 x 1200).
Download from Www.Somanuals.com. All Manuals Search And Download.
29
3
Partial, scrolling
or incorrectly
displayed image
(For notebooks)
•
•
Press "RESYNC" on the remote control or control
panel.
For an incorrectly displayed image:
•
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
•
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP
[Fn]+[F4], NEC [Fn]+[F3], Toshiba [Fn]+[F5 ]
•
•
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
®
®
4
The screen of the
notebook
computer is not
displaying your
presentation
If you are using a Microsoft Windows based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
®
®
•
If you are using an Apple Mac OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On".
5
6
Image is unstable
or flickering
•
•
Adjust the "Tracking" to correct it. Refer to the
"Image Setting" section for more information.
Change the display color depth settings on your
computer.
Image has vertical
flickering bar
•
•
Use "Frequency" to make an adjustment. Refer to
the "Image Setting" section for more information.
Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
7
8
Image is out of
focus
•
•
•
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the
required distance of 3.9 to 32.9 feet (1.2 to
10.0meters) from the projector. Refer to the "How
to Get a Preferred Image Size by Adjusting Distance
and Zoom" section for more information.
Image is stretched
when displaying a
"widescreen"
DVD title
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
•
If you play an Letterbox(LBX) format DVD title,
please change the format to Letterbox(LBX) in the
projector OSD.
•
•
If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
9
Image is too small
or too large
•
•
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the
screen.
•
Press "MENU" on the remote control or on the
control panel. Go to "Image setting --> Aspect
Ratio" and try different settings.
10
Image has slanted
sides
•
•
If possible, reposition the projector so that it is
centered on the screen.
Press the "Keystone
/
/
/
" on the OSD or the
remote control until the sides are vertical.
11
Image is reversed
•
Select "Image --> Projection" on the OSD and adjust
the projection direction.
Problems with the Projector
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2
Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
Download from Www.Somanuals.com. All Manuals Search And Download.
31
OSD Messages
#
Condition
Message
Message Reminder
1
Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it may be used. Please also check the dust
filters if they are installed. If the dust filter is clogged with
dust, please clean it. Please refer to "Cleaning and replacing
the dust filter" for details.
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
LED & Alarm Definition Listing
LED Messages
Lamp LED
Temp LED
Power LED
Red
Message
Red
--
Red
--
Blue
--
Standby
V
(power cord plugged in)
Power button ON
Lamp retry
--
--
--
--
--
--
V
Quick
flashing
Turning off
(cooling state)
--
--
--
--
V
Quick
flashing
--
--
Turning off
(cooling completed)
V
Error (thermal failure)
Error (fan lock failure)
--
--
--
--
V
V
Quick
flashing
Error (lamp breakdown)
Error (color Wheel fail)
V
--
--
--
--
V
V
Quick
flashing
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Cleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned
periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
Dust Filter
Follow these steps:
1
Turn the projector off. Wait for the Power LED to stop flashing then
unplug the power cord.
2
3
Turn the projector upside down.
To clean the dust filters, use a small vacuum cleaner designed for
computers and other office equipment.
4
If the dirt is difficult to remove or the filter is broken, please contact your
local dealer or service center to obtain a new filter.
Replacing the dust filters
1
2
Turn the projector off.
Allow the projector at least 30 mins
to cool down.
3
4
5
Unplug the power cord.
Turn the projector upside down.
Slide the bottom dust filter out and
remove it. (Illustration #1)
Insert a suitable coin into the top
cover release button (Illustration #2)
and rotate clockwise (Illustration
#3).
6
7
8
Open the top cover. (Illustration #4)
Pull the top dust filter up.
(Illustration #5)
To put the dust filters back, reverse
the previous step.
Note: Please ensure that both top and bottom dust filters are
properly installed. Otherwise there will be a warning sound and
the projector can not be turned on.
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement Suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.
$ 1
To Change the Lamp
1
2
3
4
Turn off the projector by pressing the power button.
Allow the projector at least 30 mins to cool down.
Disconnect the power cord.
Insert the suitable coin (Illustration #1), to clockwise rotates into the top
cover release button (Illustration #1) and clockwise rotate it (Illustration
#2). Then the top cover will be able to shoot automatically.
Open the top cover. (Illustration #3)
5
6
Remove the two screws that secure the lamp module (Illustration #4), and
remove the lamp cover (Illustration #5).
7
8
Pull up the lamp bar (Illustration #6).
Pull out the lamp module by force. (Illustration #7)
To replace the lamp module, reverse the previous step.
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
1
Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
2
Secure the ceiling rod using the appropriate type of four-cylinder screws.
Ceiling Mount Base
- Attach to ceiling
Ceiling Mount Base
Long Rod
Extension Rod
Long Cylinder Cap
Allen Key
- For tightening/looseni
Screw Type A
50 mm length / 8 mm diameter -
Tightening Screw
Medium Rod
Download from Www.Somanuals.com. All Manuals Search And Download.
36
3
Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Screw Type B
Smaller Washer
Large Washer
Projector Bracket
Supports projector and allows -
for adjustments
Spacer
- For heat dissipation
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4
Attach the ceiling bracket to the ceiling rod.
Large cylinder cap
Allen Key
- For tightening/loosening
Screw Type A
50 mm length -
Tightening Screw
08 mm diameter
Download from Www.Somanuals.com. All Manuals Search And Download.
37
5
Adjust the angle and positioning as necessary.
Tightening Screw
Allen Key
Allen Key
Tightening Screw
Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models
Screw Type B
Diameter (mm)
Washer Type
Length (mm)
25
Large
V
Small
V
P7270/P7270i/
P7280/P7280i
3
145 mm
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.
®
Projection system
Resolution
DLP
P7270/P7270i/P7280/P7280i Series: Native: XGA (1024 x
768), Maximum: UXGA (1600 x 1200), WSXGA+ (1680
x 1050)
Computer compatibility
Video compatibility
IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA+
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i), EDTV (480p, 576p), SDTV
(480i, 576i)
Aspect ratio
4:3 (native), 16:9
Displayable colors
Projection lens
P7270/P7270i/P7280/P7280i: 1073.7 million colors
F/ 2.52 - 2.79, f = 22.55 mm - 27.06 mm, 1.2X manual
zoom lens
Projection screen size (diagonal) 31.3" (0.80 m) - 313.5" (7.96 m)
Projection distance
Throw ratio
3.9' (1.2 m) - 32.9' (10.0 m)
63"@2m (1.57 - 1.89:1)
31.5k - 92 kHz
Horizontal scan rate
Vertical refresh scan rate
Lamp type
50 - 85 Hz
P7270/P7270i series: 280 W user-replaceable lamp
P7280/P7280i series: 330 W user-replaceable lamp
Keystone correction
Vertical Keystone and Horizontal Keystone (V.: ± 40º /
H.: ± 15º)
Audio
Internal speaker with 2 W x 2 output
Weight
P7270/7270i: 5 kg (11 lbs.)
P7280/7280i: 5.5 kg (12 lbs.)
Dimensions (W x D x H)
403.6 mm x 315.4 mm x 119.8 mm (15.9" x 12.4" x
4.7")
Remote control
Digital Zoom
Laser pointer and wired-IR function
8X
Power supply
AC input 100 - 240 V, 50 - 60 Hz
Power consumption
P7270/P7270i series: 360 W
P7280/P7280i series: 420 W
Operating temperature
5ºC to 35ºC / 41ºF to 95ºF
Download from Www.Somanuals.com. All Manuals Search And Download.
39
I/O connectors
•
•
•
•
•
•
•
•
•
•
•
•
Power socket x1
VGA input x2
Composite video x1
3 RCA Component video x 1
S-Video x1
VGA output x1
DVI-D x1: with HDCP support
HDMI x1
3.5 mm audio jack input x2
3.5 mm audio jack output x1
SPDIF RCA jack output x1
3.5 mm jack input x1: for wired IR remote
control
•
•
RS232 3-pin min dim jack x1
USB x1: for remote computer control
Below items are for P7270i/P7280i series only:
•
•
•
Wireless antenna x1
RJ45 Lan input x 1
3.5 mm jack output x1 for wireless audio output
Standard package contents
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
AC power cord x1
VGA cable x1
Composite video cable x1
DVI-D cable x1
S-Video cable x1
Component cable (3 RCA) x1
Remote control x1
Batteries x 2 (for remote control)
User's guide (CD-ROM) x 1
Quick start guide x 1
Security card x 1
Carrying case x1
Dust filter x2
Wireless antenna x1 (For P7270i/P7280i)
Battery Pack with USB PnS handy drive x1
(P7270i/P7280i)
* Design and specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Compatibility modes
A. VGA Analog
1
VGA Analog - PC Signal
Modes
VGA
Resolution
V.Frequency [Hz] H.Frequency [KHz]
640x480
640x480
640x480
640x480
720x400
720x400
800x600
800x600
800x600
60
72
75
85
70
85
56
60
72
75
85
75
60
70
75
85
70
75
85
60
72
75
85
60
75
31.50
37.90
37.50
43.30
31.50
37.90
35.10
37.90
48.10
46.90
53.70
49.725
48.40
56.50
60.00
68.70
63.80
67.50
77.10
63.98
76.97
79.98
91.10
60.00
75.23
65.3
SVGA
800x600
800x600
832x624
XGA
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280X1024
1280X1024
1280X1024
1280X1024
1280x960
1280x960
1400x1050
1600x1200
640x480
SXGA
QuadVGA
SXGA+
UXGA
Power Mac G4
60
60
66.6(67)
60
75.00
34.93
37.90
48.40
68.68
75.00
31.35
34.93
37.90
48.40
800x600
1024x768
1152x870
1280x960
640x480
640x480
800x600
60
75
75
60
PowerBook G4
66.6(67)
60
1024x768
60
Download from Www.Somanuals.com. All Manuals Search And Download.
41
1152x870
1280x960
1024x768
75
75
75
68.68
75.00
60.00
i Mac DV (G3)
2
VGA Analog - Extended Wide timing
Modes
WXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x800
1440x900
1680x1050
V.Frequency [Hz] H.Frequency [KHz]
60
75
85
60
60
60
60
47.8
60.3
68.6
44.772
49.643
59.9
65.290
B. DVI Digital
1
DVI - PC Signal
Modes
VGA
Resolution
640x480
640x480
640x480
640x480
720x400
720x400
800x600
800x600
800x600
800x600
800x600
832x624
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
V.Frequency [Hz] H.Frequency [KHz]
60
72
75
85
70
85
56
60
72
75
85
75
60
70
75
85
70
75
85
60
72
75
85
31.50
37.90
37.50
43.30
31.50
37.90
35.10
37.90
48.10
46.90
53.70
49.725
48.40
56.50
60.00
68.70
63.80
67.50
77.10
63.98
76.97
79.98
91.10
SVGA
XGA
SXGA
Download from Www.Somanuals.com. All Manuals Search And Download.
42
QuadVGA
1280x960
1280x960
1400x1050
1600x1200
640x480
60
75
60
60.0
75.23
65.3
SXGA+
UXGA
Power Mac G4
60
75.00
34.93
37.90
48.40
68.68
75.00
31.35
34.93
37.90
48.40
68.68
75.00
60.00
66.6(67)
60
800x600
1024x768
1152x870
1280x960
640x480
640x480
800x600
1024x768
1152x870
1280x960
1024x768
60
75
75
60
PowerBook G4
66.6(67)
60
60
75
75
75
i Mac DV (G3)
2
DVI - Extended Wide timing
Modes
WXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x800
1440x900
1680x1050
V.Frequency [Hz] H.Frequency [KHz]
60
75
85
60
60
60
60
47.8
60.3
68.6
44.772
49.643
59.9
65.290
Download from Www.Somanuals.com. All Manuals Search And Download.
43
3
DVI - Video Signal
Modes
Resolution
V.Frequency [Hz] H.Frequency [KHz]
For TWN/USA SKU
480i (NTSC)
480p (NTSC)
720p (NTSC)
1080i (NTSC)
1080p (NTSC)
For EMEA SKU
576i (PAL)
720x480(1440x480)
59.94(29.97)
59.94
60
15.734
31.469
44.955
33.716
67.432
720x480
1280x720
1920x1080
1920x1080
60(30)
60
720x576(1440x576)
720x576
50(25)
50
50
15.625
31.25
37.5
576p (PAL)
720p (PAL)
1280x720
1080i (PAL)
1080p (PAL)
1920x1080
1920x1080
50
50
28.125
56.25
Download from Www.Somanuals.com. All Manuals Search And Download.
44
C. HDMI -Digital
1
HDMI - PC Signal and Extended Wide timing: Support above DVI
digital timing format.
2
HDMI - Video Signal
Modes
Resolution
V.Frequency [Hz] H.Frequency [KHz]
For TWN/USA SKU
480i (NTSC)
480p (NTSC)
720p (NTSC)
1080i (NTSC)
1080p (NTSC)
For EMEA SKU
576i (PAL)
720x480(1440x480)
720x480
59.94(29.97)
59.94
60
15.734
31.469
44.955
33.716
67.432
1280x720
1920x1080
1920x1080
60(30)
60
720x576(1440x576)
720x576
50(25)
50
50
15.625
31.25
37.5
576p (PAL)
720p (PAL)
1280x720
1080i (PAL)
1080p (PAL)
1920x1080
1920x1080
50
50
28.125
56.25
15k - 92 kHz
50k - 85 Hz
Horizontal scan rate:
Vertical scan rate:
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a
Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b
Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC. (Please visit
http://global.acer.com/support/certificate.htm for complete documents.)
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules). The below information is for
products with such devices.
Download from Www.Somanuals.com. All Manuals Search And Download.
47
European Union (EU)
R&TTE Directive 1999/5/EC as attested by conformity with the following
harmonized standard:
•
Article 3.1(a) Health and Safety
•
•
EN60950-1:2001
EN50371:2002 (SAR, general FR device)
•
Article 3.1(b) EMC
•
•
•
EN301 489-1 V1.4.1 (common technical requirement)
EN301 489-3 V1.4.1 (for short range device)
EN301 489-17 V1.2.1 (for widerband data and HIPETLAN
equipment)
•
Article 3.2 Spectrum Usages
•
•
•
•
•
EN300 220-1 V1.3.1 (for short range device, 25~1000MHz, part
1)
EN300 220-2 V2.1.1 (for short range device, 25~1000MHz, part
3)
EN300 440-2 V1.1.2 (for short range device, 1G~20GMHz, part
2)
EN300 328 V1.6.1 (for data transmission equipment operating
in the 2,4 GHz ISM band
EN301 893 V1.2.3 (5GHz high performance RLAN)
List of applicable countries
EU member states as of May 2004 are: Belgium, Denmark, Germany, Greece, Spain, France,
Ireland, Italy, Luxembourg, the Netherlands, Austria, Portugal, Finland, Sweden, United
Kingdom Estonia, Latvia, Lithuania, Poland, Hungary, Czech Republic, Slovak Republic,
Slovenia, Cyprus and Malta. Usage allowed in the countries of European Union, as well as
Norway, Switzerland, Iceland and Liechtenstein. This device must be used in strict
accordance with the regulations and constraints in the country of use. For further
information, please contact a local office in the country of use.
Download from Www.Somanuals.com. All Manuals Search And Download.
48
Acer America Corporation
333 West San Carlos St., San Jose
CA 95110, U. S. A.
Tel : 254-298-4000
Fax : 254-298-4147
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product:
DLP Projector
Model Number:
DNX0712/DNX0713
Machine Type:
P7270/P7270i/P7280/P7280i series
Acer America Corporation
Name of Responsible Party:
Address of Responsible Party:
333 West San Carlos St.
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
Download from Www.Somanuals.com. All Manuals Search And Download.
49
Declaration of Conformity
We,
Acer Computer (Shanghai) Limited
3F, No. 168 Xizang medium road, Huangpu District,
Shanghai, China
Contact Person: Mr. Easy Lai
Tel: 886-2-8691-3089 Fax: 886-2-8691-3000
E-mail: [email protected]
Hereby declare that:
Product: DLP Projector
Trade Name: Acer
Model Number: DNX0712/DNX0713
Machine Type:
P7270/P7270i/P7280/P7280i series
Is compliant with the essential requirements and other relevant provisions of the following EC directives,
and that all the necessary steps have been taken and are in force to assure that production units of the same
product will continue comply with the requirements.
EMC Directive 2004/108/EC as attested by conformity with the following harmonized
standards:
-. EN55022:1998 + A1:2000 + A2:2003, AS/NZS CISPR22:2002, Class B
-. EN55024:1998 + A1:2001 + A2:2003
-. EN61000-3-2:2000, Class A
-. EN61000-3-3:1995 + A1:2001
Low Voltage Directive 2006/95/EC as attested by conformity with the following
harmonized standard:
R&TTE Directive 1999/5/EC as attested by conformity with the following harmonized standard:
• Article 3.1(a) Health and Safety
• EN60950-1:2001
• EN50371:2002 (SAR, general FR device)
• Article 3.1(b) EMC
• EN301 489-1 V1.4.1 (common technical requirement)
• EN301 489-3 V1.4.1 (for short range device)
• EN301 489-17 V1.2.1 (for widerband data and HIPETLAN equipment)
• Article 3.2 Spectrum Usages
• EN300 220-1 V1.3.1 (for short range device, 25~1000MHz, part 1)
• EN300 220-2 V2.1.1 (for short range device, 25~1000MHz, part 3)
• EN300 440-2 V1.1.2 (for short range device, 1G~20GMHz, part 2)
• EN300 328 V1.6.1 (for data transmission equipment operating in the 2,4 GHz ISM band
• EN301 893 V1.2.3 (5GHz high performance RLAN)
Easy Lai / Director
Acer Computer (Shanghai) Limited
Download from Www.Somanuals.com. All Manuals Search And Download.
|