NetVanta Unified Communications
NetVanta Unified Communications Server
Installation Guide
Version 4.5
619500001-19A
October 2009
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Conventions
Conventions
Notes provide additional useful information.
Cautions signify information that could prevent service interruption or damage to
equipment.
Warnings provide information that could prevent injury or endangerment to human
life.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventions
Unified Communications Server
4
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Installing NetVanta UC Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpacking the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing Hardware and Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing the Intel Dialogic Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Preparing to Install the NetVanta UC Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Minimum System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Starting the NetVanta UC Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Verifying the Internet Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Configuring Antivirus Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Configuring Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installing Microsoft MAPI Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Installing the Agent for IP Office Centralized Voicemail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Running the Installation Wizard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Installing NetVanta UC Server Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Backup and Restore Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Appendix A. Downloading and Installing Administration Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Windows Server 2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Windows XP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Appendix B. Managing Windows XP Built-In Firewall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
619500001-19A
Copyright © 2009 ADTRAN, Inc.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
6
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Installing NetVanta UC Server
Introduction
This guide is written for installers who perform applicable hardware and software installations prior to
configuration at the customer site. It assumes familiarity with general hardware and software installation
procedures. This guide is also intended for Microsoft® Professionals and NetVanta trained professionals to
install and configure the NetVanta Unified Communications Server.
Installing NetVanta Unified Communications Server on a Windows operating system allows you to
manage the business communications system within a Microsoft IT environment. Integration with Active
Directory allows IT administrators to manage the communications system using the same user accounts
and security policies that are used in the Windows-based environment. The automatic integration requires
no extra programming or special integration.
This guide covers the following topics:
We recommend that you perform the steps and procedures in the order they appear in this guide. Your
requirements may vary, depending on your system configuration and needs.
If you are rerunning the UC Server Installation Wizard because you are performing an
upgrade, check the release notes to determine if the Unified Communications Client software
needs to be upgraded. The release notes are available online at
Unpacking the Software
The contents of the box depend on where the UC server is being configured. When you unpack the UC
server, make sure that all the UC server and software components are included in the box. The box must
include at least the following:
• One NetVanta product CD
• Product key (on a 3-inch x 5-inch card)
Once the server is unpacked, verify its physical condition by making sure that all the cards are seated
firmly, and confirm that all internal component connections are tight.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Hardware and Software
Unified Communications Server
Installing Hardware and Software
To install the software, you need temporary use of the following:
• Monitor
• Keyboard
• Mouse
Connect the monitor, keyboard, and mouse to the server computer according to the manufacturer’s
instructions.
The server also requires a CD-ROM drive for the product CD.
Installing the Intel Dialogic Card
Make sure that the server is unplugged before you proceed.
Remember to follow proper static grounding procedures.
You will need the following to install the Intel Dialogic card:
• One of the following Intel Dialogic cards:
DEFINITY/Communication Manager
D/82JCT-U
D/82JCT-PCIUNIV
D/4PCIUF
IP Office, DEFINITY/MultiVantage, MERLIN
MAGIX PBX or Generic Analog Integration
D/120JCT-LS D/41JCT-LS
• Server on which the UC server software is to be installed
• Phillips 2 x 4 screwdriver (this may be necessary depending on the server case)
To install the Intel Dialogic card
Refer to the card's instructions and follow these steps:
1. Open the computer chassis.
2. Install each Intel Dialogic card in an available PCI slot.
8
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Preparing to Install the NetVanta UC Server
For information about installing the Intel Dialogic cards, please refer to the manufacturer’s
instructions.
3. If you disconnected any cables to open the chassis, reconnect all cables firmly.
4. Close the computer chassis.
For multiple D/82JCT cards a jumper cable is needed (CT Bus cable).
Preparing to Install the NetVanta UC Server
The following topics are covered in this section:
To correctly install NetVanta software on the server, you need to log onto the computer as a user with local
administrative rights.
We recommend that you install and configure the server at the customer site.
Additional hardware and software might be required for specific private branch exchange
(PBX) integrations.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing to Install the NetVanta UC Server
Unified Communications Server
Minimum System Requirements
For installation, the server must meet the following minimum requirements outlined below.
Processor Intel Pentium 4
3.0 GHz or higher
RAM
1 GB
Disk space 80 GB or larger
7200 RPM or faster
The server software must be installed on a 32-bit platform, unless it’s installed on
Microsoft® Windows Server 2008.
Limitations and Restrictions
This section details the operational limitations of server hardware and software configurations, as noted in
the NetVanta Unified Communications Server Planning and Deployment Guide available online at http://
kb.adtran.com.
• Do not install Microsoft SQL Server on the NetVanta UC Server on page 10
• Do not install the UC client on the same platform as Microsoft Exchange Server and Microsoft Outlook
Do not install Microsoft SQL Server on the NetVanta UC Server
Microsoft SQL Server installation is currently NOT supported on the UC server platform.
Ensure that Microsoft SQL Server is not installed when UC server is installed on the following platforms:
• Microsoft Windows 2003 Server
• Microsoft Windows 2003 Small Business Server
If you plan to install the UC server software on a computer that has Microsoft SQL Server installed, you
must remove Microsoft SQL Server software prior to installing the UC server software.
The UC server installation fails if Microsoft SQL Server is installed on the UC server platform.
Do not install the UC client on the same platform as Microsoft Exchange Server
and Microsoft Outlook
The NetVanta voice and fax forms, included as part of the UC client software installation, do not operate
correctly when Microsoft Outlook is installed on the same machine as Microsoft Exchange Server. This is
10
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Preparing to Install the NetVanta UC Server
a result of a conflict between the Microsoft Exchange and Microsoft Outlook messaging application
programming interface (MAPI) drivers. Do not install the UC client software on the following platforms:
• Any platform running both Microsoft Exchange Server and Microsoft Outlook
• Windows SBS (which includes Exchange Server and Microsoft Outlook)
• Any operating system on which both Terminal services and Microsoft Exchange services are operating
Limitations of using Microsoft Exchange Server and mailbox monitoring
Mailbox monitoring is a method of synchronizing message waiting lights on phones, using Exchange
Server to monitor when messages arrive, are read, and so on. Using mailbox monitoring enables the
synchronization of message waiting lights when messages are accessed through Microsoft Outlook Web
Access, or through a mobile device.
Performance issues may arise when mailbox monitoring is enabled. On systems with more
than 100 users, system design and engineering must consider the increased load that a large
numbers of open mailboxes will have on the Exchange Server. Enabling monitoring of more
than 500 mailboxes requires careful consideration and probably should not be done without
a slow roll-out procedure to validate the performance of both Exchange Server and UC
server in the specific customer environment. If your Exchange Server is at or near capacity,
then you may want to disable mailbox monitoring.
You can enable or disable mailbox monitoring at the system level when you add or configure Microsoft
Exchange Server. You can also set the default for users as either having mailbox monitoring on or off.
When you add or configure users, you can choose to use the server default, which is the default value, or
you can enable or disable mailbox monitoring for individual users.
For more information, refer to the NetVanta Unified Communications Server
Do not change the recovery setting for the CA Server Application Service
The recovery setting for the CA Server Application service is set to Take no Action and should not be
changed. Modifying this setting will hinder diagnosis of any startup issues, and could result in unnecessary
entries being added to the system or application event logs. The other services have been set to restart on
failure.
Starting the NetVanta UC Server
Power on the NetVanta UC Server to begin installation.
To start the UC server
1. Log in as Administrator using the password: callattendant.
2. Change the password according to the customer’s standards.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing to Install the NetVanta UC Server
Unified Communications Server
3. Select Windows Start > Control Panel > Date, Time, Language, and Regional Options > Date
and Time.
4. Change the Date & Time and Time Zone options to match the customer’s region.
5. Assign an IP address to the UC server according to the customer’s standards.
6. Connect the UC server to the LAN.
7. Add the UC server as a member of the customer’s network domain.
Verifying the Internet Connection
You need a public Internet connection to retrieve Windows software components.
Launch a browser from the server computer to make sure that you are able to connect to the Internet. If you
do not have an Internet connection, make sure there is one established before you proceed with the
installation.
Verifying the Operating System
To install the UC server, you must have one of the following operating systems installed on the server:
• Microsoft Windows Server 2008 (x86, x64)
(Deployment on Server Core or Hyper-V is not supported)
• Microsoft Windows Server 2003 R2 SP2
• Microsoft Windows Server 2003 SP1, SP2
• Microsoft Windows Small Business Server 2003 SP1 or later SP
• Microsoft Windows XP Professional SP2 or later SP
Follow the Microsoft instructions for obtaining and installing Service Pack updates. Make
sure to include all Microsoft critical security updates to maintain the security of your
computers.
An open database connectivity (ODBC) database update is required in order for the UC
server to support Microsoft Office 2007. The components required are used by non-
Microsoft Office applications to read data from Office 2007 system files, such as the new file
extensions in Microsoft Office Access 2007 (mdb and accdb) and Microsoft Office Excel
2007 (xls, xlsx, xlsb). To download the required set of Data Connectivity Components, refer
We recommend using a server operating system for all installations of UC server. While the client platform
mentioned above (Windows XP Professional SP2) is supported, it is designed by Microsoft for desktop
use, not server use. If you are using Windows XP, download and install the Microsoft Administration Tools
Pack from the Microsoft website.
12
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Preparing to Install the NetVanta UC Server
Configuring Antivirus Software
If you are installing antivirus software on the UC server platform, then ensure that it is configured to not
interfere with the regular operation of UC server.
The following folders must be excluded from the antivirus software scanning:
C:\Program Files\ADTRAN
Or any folder into which the UC server application is loaded.
C:\Logs
Or the folder to which the logging application is configured.
C:\Program Files\Microsoft SQL Server
Or the default location of the database folder.
It has been observed that third-party firewall and antivirus products can cause problems
with the proper operation of UC server. If a problem occurs, ADTRAN Technical Support
advises that third-party products be removed from the system prior to contacting Technical
Support.
The UC server is tested with Microsoft security products, such as Windows Firewall and
Windows Defender.
Configuring Services
Do not change the recovery settings for services. For more information, refer to Do not
Disabling the indexing service
Default installations of Windows Server 2003 and Windows XP enable the Indexing Service. This service
is used to improve search speeds on the local system, by continually monitoring and indexing files. This
can consume a moderate amount of CPU resources. This service is not required or used by the UC server,
and therefore it should be disabled to improve system performance. Failure to disable the Indexing Service
will cause reduced system capacity.
To turn off the indexing service
1. Select Start > Programs > Administrative Tools > Services.
2. Select the Indexing Service, right-click and select Properties.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing to Install the NetVanta UC Server
Unified Communications Server
3. Under Startup type, select Disabled.
4. Under Service status, select Stop.
5. Select Apply, and then select OK.
Installing Microsoft MAPI Connector
Integration with Microsoft® Exchange Server requires a MAPI connector to be installed on the UC server
platform.
Only one of the following supported MAPI connectors should be installed:
• Microsoft Exchange Server MAPI Client and Collaboration Data Objects 1.2.1
This is available for download free of charge from: http://www.microsoft.com/downloads/
[Version: 6.5.8069.0, 2009-Feb-16 - older versions are not compatible with all platforms]
• Microsoft Outlook 2003 SP3
Failure to use SP3 with Microsoft Outlook 2003 will cause unreliability of the
integration with Microsoft Exchange Server and may cause system outages.
• Microsoft Outlook 2007 SP1 (SP2 is not supported)
Outlook 2007 SP2 is not compatible as a server MAPI connector with UC server and
installing it will cause UC server to be unable to connect to Exchange Server.
We recommend the use of Microsoft Exchange Server MAPI Client and Collaboration Data Objects 1.2.1
instead of Microsoft Outlook. The benefits of doing this are as follows:
• No Outlook license is required for the UC server system. The MAPI/CDO software package is available
at no charge.
• The MAPI/CDO package is a minimal installation that requires fewer Microsoft updates.
• This component is designed and provided by Microsoft explicitly for the purpose of allowing
applications, such as UC server, to access Microsoft Exchange Server.
To install Microsoft Exchange Server MAPI Client and Collaboration Data Objects 1.2.1
1. Download the MAPI/CDO software package from Microsoft’s website.
2. Follow Microsoft’s instructions.
To install Microsoft Outlook software
Install Microsoft Outlook software according to Microsoft instructions.
14
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Preparing to Install the NetVanta UC Server
You need to install Outlook only if you are configuring UC server to integrate with Exchange
Server.
To integrate with Exchange Server 2007, you must install Outlook 2007 on the UC server
platform to permit connection.
If you are using Outlook 2002, you must install Outlook Service Pack 3.
Installing CTI Link/Tapi Software
Some PBX integrations may require additional hardware or software. Refer to the third-party integration
guides available online at http://kb.adtran.com/. For IP Office, refer to the Integrating IP Office technical
note. For Merlin Magix, refer to the Integrating the MERLIN MAGIX PBX technical note.
The instructions below are applicable for installing Dialogic Software 6.0. Service Update
118. For Nortel integrations, Dialogic 5.11 is used.
Once the Intel Dialogic software has been installed, verify that the cards were installed correctly. If the
cards were improperly configured, then you must update the driver. Run the Intel Dialogic Configuration
Manager to detect the Intel Dialogic hardware on the UC server. Once the cards have been properly
installed and detected, set the Intel Dialogic service to start automatically.
To install the Intel Dialogic software
1. Insert the NetVanta product CD-ROM into the computer’s CD-ROM drive.
2. Browse for Dialogic software.
3. Install the Intel Dialogic System Software Release 6.0.
4. Run the SETUP.EXE from Windows Explorer.
5. When prompted to select features, only select Core Runtime Package, and select Next.
6. When advised that the installation will install third-party software, select Yes. The installation detects
and removes any existing Intel Dialogic system software.
7. When prompted to restart the system, select Yes.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing to Install the NetVanta UC Server
Unified Communications Server
To verify the installation of the Intel Dialogic cards
• Through Windows Hardware Device Manager, verify that all of the Intel Dialogic cards reside in the
Dialogic Springware Devices section of the Device Manager on the server.
If any of the cards appear to be improperly configured, such as a Caution symbol, then you
must update the driver.
To update the driver (if the cards are improperly configured)
1. From the Device Manager, locate and configure the Intel Dialogic card.
2. Select the Driver tab and select Update Driver.
3. Select Search for suitable driver for my device (recommended) and select Next.
4. Once the driver update locates the Intel Dialogic card, select Next.
5. Repeat the steps above for each Intel Dialogic card that appears to be improperly installed or
configured.
To detect the Intel Dialogic Hardware on the UC server
1. Select Start > Programs > Intel Dialogic System Release > Configuration Manager - DCM.
Digital carrier module (DCM) detects any Intel Dialogic hardware installed on the machine running
UC server.
2. Ensure that the board settings match your PBX type. This only applies to Digital cards. The default
configuration is Nortel Norstar.
3. For digital set emulation (DSE), open each card and make sure the PBXSwitch parameter (located on
the MISC tab) is configured according to your integration. Refer to the relevant configuration guide.
4. All Dialogic cards should be started the first time from the DCM application.
To enable fax resources on the D/120JCT-LS Dialogic Cards
1. Select on Start > Programs > Intel Dialogic System Software > Configuration Manager – DCM.
2. Change the properties of each D/120JCT-LS Dialogic card by double-clicking on each card.
3. Select the MISC tab and change the Firmware File parameter to spfax.fwl.
To configure the Intel Dialogic service to start automatically
• Select Settings > System Device Autostart to Start System. It is normal to see the error message
Failed to set the Device Autostart setting. Requested data not found in NCM data storage.
To install CTI Link hardware and software
1. Install the required cards on the computer.
2. Locate the CD with the appropriate computer telephoney integration (CTI) link software.
16
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Preparing to Install the NetVanta UC Server
3. Install the software.
4. Run the manager to confirm the presence of the hardware.
The Avaya MERLIN MAGIX CTI link requires you to install the following:
• Eicon card
• CenterVu Software
• MMPD PBX driver software
• Refer to the Integrating Merlin Magix PBX technical note available online at
Avaya IP Office requires you to install the CTI link Pro software in third-party mode. Refer
Installing the Agent for IP Office Centralized Voicemail
The UC server can also work as a centralized voicemail in an IP Office environment. The corporate office
configuration for centralized voicemail is the same as a single-site IP Office deployment, and each branch
IP Office is configured the same way as the corporate IP Office. Branch IP Offices use a locally configured
group of extensions that are redirected to the main IP Office location.
Each branch office requires you to install an agent application that you can configure remotely using UC
server. The agent application redirects incoming voicemail calls to the centralized UC server. The
redirected call includes all the information needed to answer the call correctly.
To ensure that UC server can correctly identify the associated mailbox for each forwarded
call and for the message waiting light to work properly, all extensions in the corporate and
branch offices must be unique. An extension number that is used at any site must not be used
again anywhere else.
The agent operates as follows:
• Listens for calls forwarded to voicemail hunt groups at the remote site through TAPI messages.
• When a call is forwarded to the remote site voicemail hunt group, the agent then does two things:
• Sends the call party information along with a unique call identifier to the UC server running at the
corporate site using TCP/IP.
• Redirects the call to the corporate site IP Office voicemail hunt group.
• The corporate site IP Office then forwards the call to UC server, which then handles the call as if it had
been placed to an extension at the corporate office site.
When you install and configure the branch IP Office, follow the same steps as the installation of the
corporate or main IP Office. To configure IP Office, you need to know the following:
Agent IP address
The IP address of the agent computer.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Running the Installation Wizard
Unified Communications Server
Agent port
The port on which the computers communicate with each other.
The same password as the main site.
Agent password
Device-list refresh rate How often UC server refreshes its list of available devices (use default).
Heartbeat rate
Extensions
How often IP Office polls the connection.
The extensions to monitor, and the redirect number for each monitored
extension.
Before you install the agent, the host computer must have Avaya’s TAPI driver installed. The driver must
be configured to point to the location of the IP Office unit at the remote site where the agent is being
installed.
For more information about installing and configuring Avaya’s TAPI driver, refer to the
To install the agent
1. Start the agent installer application.
2. At the prompt, select an installation directory.
3. At the prompt, select the password that you want UC server to use to authenticate with the agent.
The password that you choose must be the same as the password value configured on
UC server for the corresponding agent.
4. At the prompt, select a TCP port to communicate with UC server. Make sure that the TCP port you
select is not used by another application.
The port that you choose must be the same as the port value configured on UC server
for the corresponding agent.
Running the Installation Wizard
Run the UC Server Installation Wizard to install the UC server software. Running the wizard also allows
UC server to automatically detect the Microsoft Windows minimum requirements, such as service packs
and updates.
Make sure that you run the installation from a Windows logon that has the ability to install software on the
UC server.
Run the software by putting in the CD, or navigating to the folder that contains the software. If it does not
run automatically, select CAAutoRun.exe.
18
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Running the Installation Wizard
The UC Server Installation Wizard includes the following steps:
Makes sure that all prerequisite components, such as the
Windows 2003 Server Administration Tool Pack, are
installed.
Starts the UC Server Configuration Wizard.
For information about running the UC Server Installation Wizard to upgrade your
Instruction document that applies to your upgrade.
Installing Prerequisite Components
The UC server requires that prerequisite components are installed prior to installing UC server. The
installer detects which components are missing from the system and prompts accordingly. Many of the
prerequisite components are included on the CD and can be automatically installed. For example, the UC
Server Logging Tools is a prerequisite that you can automatically install. In the event of a crash, a crash
*.dmp file is automatically generated, if the user has been granted Debugger User permissions. Refer to the
UC Server Administrator Manual for more information.
ADTRAN cannot include all the prerequisites on the CD because of redistribution
restrictions, and therefore some prerequisites must be obtained directly from the vendor. If
you need to download any of the prerequisites, the relevant websites are provided by the
installer.
Not all prerequisites are required on all operating systems. Except where indicated, the prerequisites are
installed automatically by the installer.
Prerequisite components
• Visual Studio 2005 SP1 Redistributable Files
• UC Server Logging Tools
• Microsoft SQL Server 2005 Express Edition SP2
The UC server only works correctly with the Microsoft SQL Server version that is provided
on the distribution media. Please ensure that any existing installation of Microsoft SQL
Server is completely removed from the machine prior to installing UC server.
Prerequisite components for Windows Server 2008 only
• Windows Server 2008 Enhanced Desktop Feature (a reboot is required after installation)
619500001-19A
Copyright © 2009 ADTRAN, Inc.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Running the Installation Wizard
Unified Communications Server
Prerequisite components for Windows XP only
• Microsoft Windows Server 2003 SP1 Administration Tools Pack (download link provided in installer)
• Microsoft .NET Framework 2.0
To automatically install prerequisite components from the NetVanta CD
• On the Preparing UC Server Installation menu, select Verify or automatically install remaining
components.
20
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Preparing to Configure the NetVanta UC Server
Installing NetVanta UC Server Software
After all the prerequisite components are successfully installed, the wizard prompts you to install UC
server.
Preparing to Configure the NetVanta UC Server
The UC Server Configuration Wizard allows you to specify server properties, such as message store,
administrator password, PBX information, and dialing properties. The wizard steps you through the UC
Server configuration process. The wizard does most of the configuration tasks automatically, however you
need to enter some information about the network and server.
You can choose not to run the Server Configuration Wizard, and restart the wizard at a later
time.
We recommend that you run the Server Configuration Wizard at the customer’s site to ensure
the successful integration of Active Directory and Microsoft Exchange.
Before you start the Server Configuration Wizard, you need to do each of the following:
• Obtain the License Key from ADTRAN.
ADTRAN generates a unique software license using the following formula:
License Key = Purchase key + Machine ID + Features (upgrade keys)
619500001-19A
Copyright © 2009 ADTRAN, Inc.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Backup and Restore Procedures
Unified Communications Server
• Log onto the UC server as at least a local user with Administrative rights, preferably with domain
Administrator privileges on the network.
• Make sure UC server is connected to the PBX ports and network.
• Gather all the following information:
• Service account name and password (verify permissions for Exchange integrations).
• User name and associated extensions.
• PBX ports, hunt group, message waiting light information and trunk information.
• Dialing rules (for example, area codes, account codes, 10-digit dialing).
To start the Server Configuration Wizard
1. Log on as a user with local Administrative rights.
2. Select Windows Start > Programs.
3. Select NetVanta UC > Server Configuration Wizard. The Configuration Welcome menu appears.
For more information about the UC Server Configuration Wizard, refer to the NetVanta
kb.adtran.com.
Backup and Restore Procedures
For instructions on backup and restore procedures, refer to the NetVanta Unified Communications Server
Planning and Deployment Guide. This document is available on the installation media (CD or download),
22
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Downloading and Installing Administration Tools
This appendix provides details for some of the steps that appear in the NetVanta Unified Communications
Server Installation Guide.
To remotely administer UC Server, you must install remote administration tools. The administration tools
allow administrators to install management tools to perform remote server management functions.
The administration tools may be automatically downloaded by the UC Server Installation Wizard.
However, if the platform does not have access to the Internet when you are running the UC Server
Installation Wizard, you may need to download and install the tools manually.
Windows Server 2003 and Windows Small Business Server 2003 automatically include the
Windows Administration tools.
The instructions for manually installing the administration tools for the following operating systems are
provided in this appendix:
Windows Server 2008
To install remote administration tools for Windows Server 2008
1. Open Server Manager, or Control Panel > Programs and Features, and select Turn Windows
features on or off.
2. Select Features. This displays the Features section, which includes the list of all currently installed
features.
3. Select Add Features.
4. From the list of available features, select Remote Services Administration tools > Role
Administration tools > Active Directory Domain Services tools, and select Next.
5. Select Install.
6. Reboot the server for the changes to take effect.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows Vista
Unified Communications Server
Windows Vista
In order to install the remote server administration tools for Windows Vista, Service Pack 1
must be installed. If Service Pack 1 is not installed, then the installation of the tools will fail.
To download the Remote Server Administration Tools for Windows Vista
2. Under Downloads & Trials, select Download Center.
3. Search for Administrator Tools Pack.
4. Download the Microsoft Remote Server Administration Tools for Windows Vista.
To install the Remote Server Administration Tools on Windows Vista
1. Double-click the downloaded package to start the Setup wizard.
2. Follow the instructions in the wizard to complete the installation.
3. Open the Control Panel, select Programs, and under Programs and Features, select Turn
Windows features on or off.
4. If you are prompted to provide permission by User Account Control, select Continue.
5. In the Windows Features dialog box, select the remote administration snap-ins and tools that you
want to install, and select OK.
To configure the Start menu to display the Administration Tools shortcut
1. Right-click Start, and then select Properties.
2. On the Start Menu tab, select Customize.
3. In the Customize Start Menu dialog box, scroll down to System administrative tools, and then
select Display on the All Programs menu and the Start menu, and select OK.
For a complete list of tools included in the package, installation instructions, and other
help topics, refer to Remote Server Administration Tools Help in the Administrative
Tools list on the Start menu.
24
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Unified Communications Server
Windows XP
Windows XP
Windows Server 2003 and Windows Small Business Server 2003 automatically include the
Windows Administration tools.
You can download the Windows Server 2003 Administration Tools Pack for installing the Windows Server
2003 management tools onto Windows XP Professional or Windows Server 2003.
To download the Windows Server 2003 Administration Tools Pack
2. Under Downloads & Trials select Download Center.
3. Search for Administrator Tools Pack.
4. Download the appropriate version of the Windows Server 2003 Administration Tools Pack.
To install or reinstall using a Windows Server 2003 family CD
1. Put your Windows Server 2003 CD into the CD tray of the computer on which you want to install the
Administration Tools Pack.
2. When the Welcome menu appears, select Perform additional tasks.
3. Select Browse this CD.
4. Open the server cd i386 folder.
5. Right-click adminpak.msi, and then select Install.
To install or reinstall using a Windows Server 2003 family CD image or network file share
1. Put your Windows Server 2003 CD into the CD tray of the computer on which you want to install the
Administration Tools Pack.
2. Open the i386 folder on the Windows Server 2003 operating system image or network file share.
3. Right-click adminpak.msi, and then select Install to begin installation of Windows Server 2003
Administration Tools Pack onto the Windows XP Professional operating system.
If the Welcome to the Microsoft Server 2003 Family menu does not appear, select
Start, then Run. Select Browse and select the drive holding the server CD. In the
Browse dialog box, set Files of type to All files, and open the server cd i386 folder.
Right-click adminpak.msi, and then select Install.
619500001-19A
Copyright © 2009 ADTRAN, Inc.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Windows XP
Unified Communications Server
26
Copyright © 2009 ADTRAN, Inc.
619500001-19A
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B. Managing Windows XP Built-In Firewall
This appendix provides details for managing the Windows XP built-in firewall which also appears in the
NetVanta Unified Communications Server Installation Guide.
The Server Installation Wizard automatically opens the Transmission Control Protocol (TCP) ports. If the
wizard does not perform this task, you can do so manually by following the procedure below.
If the Windows XP built-in firewall is installed and enabled, you must open the TCP ports listed below to
allow UC client to communicate with UC Server, and to prevent pop-up security warnings.
To open the TCP ports
1. Select Windows Start > Programs > Accessories > System Tools > Security Center.
2. Select Windows Firewall > Exceptions > Add Ports.
3. Enter the following name and TCP port numbers:
•
DefaultServerPortNumber = 5746
• DefaultFTPServerPortNumber = 5747
DefaultAudioStreamingServerPortNumber = 5749
•
619500001-19A
Copyright © 2009 ADTRAN, Inc.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
|