GBC 2064WF-1
Operation Manual
GB
I
Operating Instructions
Istruzioni per l'Uso
Bedienungsanleitungen
Gebruiksaanwijzing
Mode d'Emploi
D
NL
F
E Instrucciones de Operación
Part Number: ???-???
© 2009 General Binding Corporation an ACCO Brands CO.
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
TABLE OF CONTENTS
Operation Manual
Page
No.
1
Page
No.
15
Description
Description
Cover
LCD Error Screens
Legal Disclaimer
Table of Contents
Important Safety Instructions
Important Safeguards
2
3
4
4
Sequence of Operations
Operating Instructions
16
17
Film Loading and Threading
Load a Roll of Film
Webbing Thermal Film using
Threading Card
Webbing PSA Film / Mount Adhesive
Using Threading Card
Start Laminating
Method for Tacking new Film to
Existing Film
To Unweb The Laminator
Clearing a Film Jam (Wrap– Up)
17
17
Warranty
Specifications
Pre- Installation
Installation
Control Panel
LCD Display
Master Dial
Top Temp
Bottom Temp
Speed
5
6
7
7
8
8
8
8
8
8
8
8
8
8
8
8
18
19
20
21
22
22
Cooling
Measure
Reset
Stop
Rear
Forward
Applications
23
23
23
23
24
24
24
25
Tips for Pre-Coating Boards
Tips for Mounting Pre-Coated Boards
Tips for Single Sided Lamination
Tips for Creating a Decal
Tips for Mounting a Decal
Thermal Encapsulation
Rear Control
Stop
9
9
9
9
AccuShield™
Rear
Forward
26
Speed/Temperature Control
Features Guide
10
10
10
10
10
10
10
11
11
11
11
11
11
11
12
12
12
12
12
13
13
13
14
14
14
14
26
26
26
27
27
The Art of Lamination
Basic Rules
Film Tension
Heat
Emergency-Stop Buttons
Media Table
Infeed Idler
Pressure Plate
Output
Safety Interlock Switch
Pressure Plate Release Lever
Rear Media Table
Table Interlock Switch
Optical Safety System
Main Rollers
Pull Rollers
Rewind Tubes
Upper Tension Idler
Lower Tension Idler
Unwind Brake Tensioner
Supply Shaft
26
29
30
Maintenance
Trouble Shooting Guide
Service Agreement
Core Chucks
Cooling Fan Bridge
Nip Pressure Adjustment
Main Roller Lift Handle
On/Off Switch &Fuses
Main Power Cord
Foot Switch
Pull Roll Clutch
IR Sensor
© 2009 General Binding Corporation an ACCO Brands CO.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFEGUARDS
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS
IMPORTANT TO GBC. IN THIS INSTRUCTION MANUAL
AND ON THE PRODUCT, YOU WILL FIND IMPORTANT
SAFETY MESSAGES REGARDING THE PRODUCT. READ
THESE MESSAGES CAREFULLY. READ ALL OF THE
INSTRUCTIONS AND SAVE THESE INSTRUCTIONS FOR
LATER USE.
WARNING: TO GUARD AGAINST INJURY THE
FOLLOWING SAFETY PRECAUTIONS MUST BE
OBSERVED IN INSTALLATION AND USE OF
THE LAMINATOR.
General:
Keep hands, long hair, loose clothing, and articles such as
necklaces or ties away from the front of the heat and pull
rollers to avoid entanglement and entrapment.
THE SAFETY ALERT SYMBOL PRECEDES
EACH
INSTRUCTION
SAFETY
MESSAGE
THE
IN
SYMBOL
THIS
The heat rollers can reach temperatures over 300˚F (150°C).
Avoid contact with the heat rollers during operation or shortly
after power has been removed from the laminator.
MANUAL.
INDICATES A POTENTIAL PERSONAL SAFETY
HAZARD TO YOU OR OTHERS. THE
FOLLOWING WARNINGS ARE FOUND UPON
THIS PRODUCT.
Keep hands and fingers away from the path of the sharp film
cutter blade located at the film exit.
ADVERTENCIA
Attention
Avertissement
Do not use the laminator for other than its intended purpose.
Riesgo de choque
eléctrico
No abra:
Adentro no hay
piezas reparables
por el usuario.
Mantenimiento
solamente por
personal calificado
Risque de
Electrical shock
hazard.
Do not open.
No user serviceable
parts inside.
Refer servicing to
qualified service
personnel.
Secousseélectrique.
Ne pas ouvrir.
Pas de pièces
réparables par
l'utilisateur.
Avoid moving the Laminator on uneven floor surfaces. Never
tilt the laminator.
Entretien
Do not defeat or remove electrical and mechanical safety
equipment such as interlocks, shields and guards.
seulement par
personnel qualifié.
Do not insert objects unsuitable for laminating or expose the
equipment to liquids.
THIS SAFETY MESSAGE MEANS THAT YOU COULD BE
SERIOUSLY HURT OR KILLED IF YOU OPEN THE
PRODUCT AND EXPOSE YOURSELF TO HAZARDOUS
VOLTAGE.
Electrical:
The Laminator should be connected only to a source of power
as indicated in these instructions and on the serial plate located
on the rear of the laminator. Contact an electrician should the
attachment plug provided with the Laminator not match the
receptacles at your location.
ADVERTENCIA
Attention
ROULEAUX
CHAUDS.
POINT DE
Avertissement
HOT ROLLS.
RODILLOS
CALIENTES.
PUNTO DE
PINCHAMIENTO. PINCEMENT.
Mantener manos y Tenir mains et
PINCH POINT.
Keep hands and
clothing away.
ropa a distancia.
vêtements à
l'écart.
THIS SAFETY MESSAGE MEANS THAT YOU COULD BE
BURNED AND YOUR FINGERS COULD BE TRAPPED
AND CRUSHED IN THE HOT ROLLERS. CLOTHING,
JEWELRY AND LONG HAIR COULD BE CAUGHT IN THE
ROLLERS AND PULL YOU INTO THEM.
WARNING:
THE RECEPTACLE MUST BE
LOCATED NEAR THE EQUIPMENT AND EASILY
ACCESSIBLE.
ADVERTENCIA
Attention
LAME
Avertissement
Do not operate the Laminator with a damaged power supply
cord or attachment plug, upon occurrence of a malfunction, or
after the laminator has been damaged. Contact GBC’s
Technical Service Department or your dealer/distributor for
assistance.
NAVAJA FILOSA.
SHARP BLADE.
COUPANTE.
Mantener manos y
dedos a distancia.
Keep hands and
clothing away.
Tenir mains et
doigts à l'écart.
THIS SAFETY MESSAGE MEANS THAT YOU COULD
CUT YOURSELF IF YOU ARE NOT CAREFUL.
Service:
WARNING: THIS SAFETY ALERT SYMBOL
PRECEDES EACH SAFETY MESSAGE IN THIS
Perform only the routine maintenance procedures referred to in
these instructions
INSTRUCTION
INDICATES A POTENTAL PERSONAL SAFETY
HAZARD TO YOU OR OTHERS.
MANUAL.
THE
SYMBOL
WARNING: DO NOT ATTEMPT TO SERVICE OR
REPAIR THE LAMINATOR
WARNING: DO NOT ATTEMPT TO SERVICE OR
REPAIR THE 3064 WF LAMINATOR.
WARNING:
DO
NOT
CONNECT
THE
Disconnect the plug from the receptacle and contact GBC’s
Technical Department or your dealer/distributor when one or
more of the following has occurred.
LAMINATOR TO AN ELECTRICAL SUPPLY OR
ATTEMPT TO OPERATE THE LAMINATOR
UNTIL YOU HAVE COMPLETELY READ THESE
INSTRUCTIONS.
INSTRUCTIONS IN A CONVENIENT LOCATION
FOR FUTURE REFERENCE.
MAINTAIN
THESE
•
•
•
•
The power supply cord or attachment plug is damaged.
Liquid has been spilled into the laminator.
The laminator is malfunctioning after being mishandled.
The laminator does not operate as described in these
instructions.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
WARRANTY
Operation Manual
Limited 90- Day Warranty
GBC warrants to the original purchaser for a period of ninety days on labor and one year on parts after installation that this laminator is free
from defects in workmanship and material under normal use and service. GBC’s obligation under this limited warranty is limited to
replacement or repair, at GBC’s option, of any part found defective by GBC without charge for material or labor.
THIS LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED. WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR
A
PARTICULAR PURPOSE ARE EXPRESSLY EXCLUDED. ANY
REPRESENTATIONS OR PROMISES INCONSISTENT WITH, OR IN ADDITION TO, THIS LIMITED WARRANTY ARE
UNAUTHORIZED AND SHALL NOT BE BINDING UPON GBC. IN NO EVENT SHALL GBC BE LIABLE FOR ANY SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES, WHETHER OR NOT FORESEEABLE.
This limited warranty shall be void if the laminator has been misused; mishandled; damaged by negligence, by accident, during shipment, or
due to exposure to extreme conditions; repaired, altered, moved, or installed by anyone other than GBC or its authorized agents; or if
incompatible film was used. GBC’s obligation under this limited warranty does not include routine maintenance, cleaning, adjustment, normal
cosmetic or mechanical wear, or freight charges.
Without limiting the generality of the previous paragraph, GBC’s obligation under this limited warranty does not include:
1. Damage caused to the rollers by knives, razors, or other sharp tools: by any foreign objects falling into the working area of the laminator; or
by cleaning the laminator with solutions or materials that harm its surfaces;
2. Damage caused by adhesives; nor
3. Damage caused by lifting, tilting or attempting to position the laminator other than rolling it on its castors across even surfaces.
FOR EUROPEAN UNION RESIDENTS ONLY: This guarantee does not affect the legal rights which consumers have under applicable
national legislation governing the sale of consumer goods.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
SPECIFICATIONS
Operating Speed
Up to 18 fpm (5.5 mpm) MAX
300°F (149°C)
Maximum Temperature
Maximum Mounting
Thickness
Main Roller-1 in. (25.4 mm) Max.
Pull Roller-1/2 in. (12.5mm) Working gap. 1 in. total opening gap.
64 in. (162.5 cm)
Maximum Film Width
Dimensions (W x D x
H)
Unit alone: (Uncrated)
82.5in x 41in x 54in
(209cm x 104cm x 137cm)
Depth of 2064WF-1 is 44in (112 cm) with tables in up position.
Weight
Unit alone: 1500 lb (680 Kg).
Shipping: 1700 lb (771 Kg).
Electrical Requirements
Refer to the serial plate located on the rear of the laminator for the specific electrical rating
applicable to the unit.
220V, 40Amps, 60 HZ. Single Phase. 8500Watts
380VAC, 13Amps, 50HZ. 3 Phase, 8500 Watts
US Models-
CE Models-
FCC NOTE
FCC Class A Notice - Notification pour les Etats-Unis
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiated radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at their
own expense.
Canada Class A Notice - Avis Canada, Class A
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Modifications
Any modifications made to this device that are not approved by General Binding Corporation
may void the authority granted to the user by the FCC and/or by Industry Canada to operate this
equipment.
Toutes modifications apportées à ce dispositif et non approuvées par General Binding
Corporation annuleront le droit accordé à l'utilisateur par le FCC et/ou par Industrie Canada de
faire fonctionner cet équipement.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
PRE-INSTALLATION
Before a 2064WF-1 Laminator can be installed, ensure
the following requirements are met:
1. Are doorways and hallways wide enough for
the laminator to be moved to the installation
site?
2. Is there ample room for the laminator?
•
A work area must be established that allows
for operation in both the front and rear of
the laminator and provides space for
efficient material flow.
3. Is the environment appropriate for the
laminator?
•
The laminator requires a clean, dust and
vapor free environment to operate properly.
Avoid locating the laminator near sources
of heat or cold. Avoid locating the
laminator in the direct path of forced,
heated or cooled air.
•
CAUTION: Air flow can cause uneven
heating / cooling of the rollers and result in
poor output quality.
4. Have you contacted a certified electrician to
wire the receptacle and ensure that adequate
power is being supplied, having the
appropriate capacity, over current protection
and safety lockouts available?
GBC 2064WF-1 WF Requires:
•
•
220V at 60Hz with 40 amps single phase.
Nema 6-50 P 50 A 250V Receptacle
This Machine is supplied with a Nema 6-50 male
plug.
INSTALLATION
1. Shipping damage should be brought to the immediate attention of the delivering carrier.
2. With assistance, carefully roll the laminator into position over flat and even surfaces.
3. The laminator should be positioned to allow exiting film to flow freely to the floor or a work table. Accumulation
of laminate immediately behind the laminator as it exits the equipment may cause the film to wrap around the pull
rollers, resulting in a “jammed” condition.
4. Avoid locating the laminator near sources of heat or cold. Avoid locating the laminator in the direct path of forced,
heated or cooled air.
5. Once the laminator has been properly positioned, lock the castors in place. Locking the castors prevent the
machine from rolling during set up, operation or servicing.
6. Connect the attachment plug provided with the laminator to a suitably grounded outlet. Avoid connecting other
equipment to the same branch circuit to which the laminator is connected, as this may result in nuisance tripping
of circuit breakers or blowing fuses.
Note:
Machine must be leveled to ensure best performance. Level the machine by lowering both the main and pull rolls.
Lay a level on top of the main and pull rolls. Then, check level from main roll to pull roll on right and left side of
the roll. Finally, check by placing the level diagonally across lower main to lower pull rolls.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
CONTROL GUIDE
•
•
GAP: As the rollers are lifted, the GAP is
measured digitally. The value is shown as a
percentage. No GAP equals 000%, completely in
the up positions equals 100%.
1
Set Temp.
Current Temp.
PRS: PRS refers to the amount of downward
pressure being applied to the Main Rollers. The
value is shown as a percentage. FIGURE 5
shows the PRS is set for 30%. No Pressure will
equal 000%, maximum pressure will read 100%.
TOP: 140*F
TOP: 145*F
GAP: 000%
TOP: 150*F
BOT: 150*F
MODE: FWRD
SPEED: 08ft
PRS: 030%
2. Master Dial:
Increases (+) or decreases (-) the numeric
value for the selected setting when turned.
3. Top Temp:
When pressed, permits increasing or
•
3
8
Reset
2
•
Top Temp
decreasing of the top set temperature by
turning the MASTER DIAL and is indicated
on the control panel display. Range is 32°F-
300°F.
MASTER DIAL
4
7
Meas.
Bottom Temp
4. Bottom Temp:
5
Speed
6
Cooling
•
When pressed, permits increasing or
decreasing of the bottom set temperature by
turning the MASTER DIAL and is indicated
on the control panel display. Range is 32°F-
300°F.
9
10
11
Rear
Forward
Stop
5. Speed:
FIGURE 1
•
When pressed, permits increasing or
decreasing of speed by turning the MASTER
DIAL and is indicated on the control panel
display. Range is 1-15.
A. Power ON/OFF (I/O):
Located at the back left of the machine applies power to
the laminator. The control panel display will illuminate
when position marked “I” is pushed. The Off position,
marked “O” removes power from the laminator.
6. Cooling:
When pressed, turns on the cooling fans.
When pressed again, turns off the cooling fans.
7. Measure:
•
•
When pressed, allows the operator to view the
amount of linear feet that the machine has run.
B. Control Panel (FIGURE 1)
1. Main display Read out:
8. Reset:
•
Illuminates when the laminator is plugged in and
POWER ON/OFF is in the on, (I), position.
Displays settings for the top heater, bottom
heater, speed, job mode, and ready/wait.
•
When pressed, permits the operator to rest the
linear feet counter.
9. Stop:
•
10. Rear:
•
When pressed, the rollers will stop rotating.
•
•
•
TOP: Refers to the Top Main Rollers
temperatures setting and Current Temperature.
When pressed, the rollers will allow the
operator to run the machine in reverse or the
rear.
BOT: Refers to the Bottom Main Rollers
temperatures setting and Current Temperature.
MODE: Displays the Direction the rollers are set
to... In FIGURE 5, the MODE is shown in the
“FWRD” position.
11. Forward:
•
When pressed, the rollers will allow the
operator to run the machine in forward mode
or from the front.
•
SPEED: Speed is displayed in Feet per Minute or
ft/mn. FIGURE 5 Displays the Speed set at 8ft.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
REAR CONTROL
A. Stop Button:
•
While running the machine from the Rear, by
pressing the “STOP” button, the rollers will
stop.
B. Rear Button:
By pressing the “Rear” button, the machine will
work going to the rear of the machine.
C. Forward Button:
By pressing the “Forward” button, the machine
will work going to the front of the machine.
•
•
© 2009 General Binding Corporation an ACCO Brands CO.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
FEATURES GUIDE
Refer to the following pages for detailed information on the above Features
FEATURES GUIDE (DETAILED DESCRIPTION)
FIGURE 1
EMERGENCY STOP BUTTONS:
(Fig. 1– Item A)
Four Emergency Stops buttons are available
on the Laminator on the top four corners of
the Laminator.
To engage Emergency -stop button, press any
emergency -stop safety push button to stop
the roller movement
To disengage turn the push button clockwise
after the emergency condition has been
A
FIGURE 2
Front Media Table:
The Media Table (Fig.2A) is used to position
items for Lamination. There are two media
tables on the machine one on the front & one
on the rear of the Laminator. The Front
Media table incorporates an Idler on the
leading edge of the table.
Infeed Idler:
The Infeed Idler (Fig.2C) is used for roll to
roll applications during lamination.
Pressure Plate:
The Pressure Plate (Fig. 2B) helps to keep
images flat and assists when feeding images.
FIGURE 3
Safety Interlock Switch:
On both the Front Media & Rear Media
tables, the Safety Interlock Switch (Fig.3A)
will not allow the Laminator to operate at full
speed unless the tables are properly installed.
Pressure Plate Release Lever:
The Pressure Plate Release Lever (Fig.3B)
will allow the operator to remove the Pressure
plate by pulling the lever out, releasing the
locking pin, and remove the Pressure Plate.
Note:
The Laminator will operate only when the
Media Table and Media Table Latch are
Properly Installed
© 2009 General Binding Corporation an ACCO Brands CO.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
FIGURE 4
Rear Media Table:
The Rear Media Table (Fig.4A) is used to
position items for Lamination. There are two
media tables on the machine one on the front &
one on the rear of the Laminator.
Table Safety Interlock Switch:
The Table Safety Interlock Switch (Fig.4B)
ensures that the table is properly placed and
secure. The Safety Interlock Switch will not
allow the Laminator to operate at full speed unless
the tables are properly installed.
FIGURE 5
Optical Safety System:
The Optical Safety System (Fig. 5A&6A) utilizes
2 optical beams located at the Main Roll Nip as
well as the Pull Roll Nip. Once the Optical Eye is
blocked, the machine will instantly stop unless the
operator is using the Foot Switch. While using the
Foot Switch and the Optical Eye is blocked, the
machine will only operate at a fixed speed of
3ft/mn. Please refer to the Sequence of Operation.
Main Rollers:
The 2 Main Rollers (Fig.5 B&C) are used to
apply Heat and Pressure to films being used.
Silicone rubber coated steel tubes heat the
laminating film and compresses the heated film to
the items being laminated. Heat is provided by an
internal heating element.
FIGURE 6
Pull Rollers:
The Pull Rollers (Fig.6 B&C) located at the back
of the laminator are motor driven and the lower
roller is clutched. They simultaneously pull the
film and image.
Rewind Tubes:
FIGURE 7
The Rewind Tubes (Fig.7A) are used to rewind
release liners or finished Medias.
Upper Tension Idler: (Fig.7B)
The Upper Tension Idler Guides the upper
lamination onto the Top Main Roller insuring a
constant amount of wrap on the Top Main Roller.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
FIGURE 8
Lower Tension Idler: (Fig.8A&9A)
The Lower Tension Idler Guides the lower
lamination onto the Bottom Main Roller insuring a
constant amount of wrap on the Bottom Main
Roller.
Unwind Brake Tensioner:
The Unwind Brake Tensioner (Fig.8B) is used to
adjust the amount of brake that is being applied to
the film or media.
Supply Shaft:
The Supply Shaft (Fig.8C&9A) is used to hold
film to be used, and to apply brake tension.
FIGURE 9
Core Chuck:
Bi-Directional Core Chucks (Fig.8D) grip the
Medias supply tube. Our patented roller core
chuck will allow the operator the ability to add or
remove film with ease.
FIGURE 10
Unwind Brake Tensioner:
The Unwind Brake Tensioner (Fig.10A) is used
to adjust the amount of brake that is being applied
to the film or media.
FIGURE 11
Cooling Fan Bridge: (Fig.11A)
There are 3 internal Cooling Fans. The fans can
be used to cool down media while it passes
through the Main Rollers and into the Pull Rollers.
Rewind Tubes:
The Rewind Tubes (Fig.11B) are used to rewind
release liners or finished Medias.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
FIGURE 12
Nip Pressure Adjustment:
The Nip pressure adjustment allows the operator to
adjust the downward pressure of the pull rolls and
main rolls.
Pull Roll Lift Handle: (Fig. 12)
Select the setting from the pre-set values and lock
latch into the appropriate slot.
-Open
-1 Inch
-3/4 Inch
-1/2 Inch
-3/8 Inch
-3/16 Inch
-1/16 Inch
-Low Pressure
-High Pressure
FIGURE 13
Heated Main Roll Lift Handle: (Fig.13)
Turn handle clockwise to lower main roll & adjust
the Nip Pressure.
On Off Switch: (Fig. 14) to apply Main Power to
the Laminator, Press the switch to the “ON”
Position. To disconnect Main Power to the
Laminator, press the switch to the “OFF” position.
FIGURE 14
Fuses: (Fig. 14)
There are 4 fuses. Each one is labeled to describe
each fuses function.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
FIGURE 15
Main Power Cord: (Fig. 15A)
The Main Power Cord Plugs into the Main Power
Supply. See Power Requirements in the Specs
part of the manual for required Voltage and
Amperage.
Foot Switch: (Fig.15B)
The Foot Switch allows the operator to run the
machine hands free. When the PICO System is
not blocked, the Foot Switch will activate the
Main Rollers, and the machine will run at the set
speed on the Main Control Panel. The Speed can
be adjusted by selecting the Speed button and
using the Main Dial to increase or decrease speed
while unit is running.
A
B
Pull Roll Clutch Adjustment Knob:
(Fig. 16A)
FIGURE 16
The Pull Roll Clutch provides tension on the
laminated film between the main rolls and pull
rolls as the material is cooling.
FIGURE 17
IR Sensor:
The IR Sensor (Fig. 16A) reads the temperature of
the Rollers. The Top IR Sensor is shown in Fig.
17. The Lower IR Sensor is located under the
Lower Heat Roller and reads the temperature of
the Lower Heat Roller
© 2009 General Binding Corporation an ACCO Brands CO.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
LCD ERROR SCREENS
Set Temp.
TOP:150*F
Current Temp.
TOP:098*F
FIGURE 1:
ESW SW PRESSED!!! -Indicates that an
Emergency Stop is activated. Locate the
Emergency Stop and release it. This will return
the machine to normal operating condition.
BOT:150*F
BOT:098*F
GAP:000%
MODE:FWRD
ESW SW PRESSED!!!
FIGURE 1.
FIGURE 2.
FIGURE 3.
FIGURE 2:
SAFETY INTERLOCKED!!! -Indicates that a
Table Inter lock is not positioned correctly. Locate
the Table Inter-locks and verify that they are
activating the Micro-Switch. Once the Table
Inter-Lock is positioned correctly the machine will
return to normal operating condition.
FIGURE 3:
TOP HTR ERR!!! -Indicates that the Top
Temperature has exceeded the set point drastically.
Verify that the IR Sensors are not blocked. If they
are blocked by film or media, remove the film or
media…press and hold the Master Dial on the
Control Panel. The machine will return to normal
operating condition.
FIGURE 4:
BOT HTR ERR!!! -Indicates that the Bottom
Temperature has exceeded the set point drastically.
Verify that the IR Sensors are not blocked. If they
are blocked by film or media, remove the film or
media…press and hold the Master Dial on the
Control Panel. The machine will return to normal
operating condition.
FIGURE 4.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
SEQUENCE OF OPERATIONS
Diagram #1
GBC U.S 2064WF-1
Effect of Fiber Optics on sequence of operation
Modes
Situation 1
Situation 2
Situation 3
Machine Run Mode
Normal operation
(No Interruption to any
safety circuitry & Fiber
optic beam)
Interrupted optic beam
or opened any safety
circuitry.
Optic beam cleared + all safety
circuitries are closed
High speed.
Control panel:
Forward Speed: Zero to
Max.
Press “Run” push button
to switch over from foot
switch to the control
panel.
Machine stops Instantly.
Use foot pedal to override
@ 3f/m.
Machine will remain stationary until
run switch is pressed.
Push RUN button switch to run machine
again (Normal operation) mode.
Foot switch:
Forward Speed: Zero to
Max.
Note: Press foot pedal
to change mode and
take over from control
panel at preset speed.
Machine Runs @
3f/m.
(Automatic override from
high to low voltage)
Machine still remains at low voltage
speed of 3f/m.
Steps required to run at (various speed):
The operator will have two choices,
Forward Mode
Press push button
forward switch
Choice A:
1. Release foot pedal to stop machine.
2. Press foot pedal again to start
machine at original preset control panel
knob speed (pot).
Choice B:
1. Press and hold “Run” push button
switch on the control panel while foot is
still on pedal.
2. Release foot pedal.
3. Adjust speed using “speed knob”
Reverse speed: Zero to
Max.
Machine stops Instantly.
Use Foot pedal to
Machine must not run. It will remain
stationary.
Press “Run” push button
to switch over from Foot
switch to the Control
panel.
override @ 3f/m.
Push RUN button switch to run machine
again at Normal operation mode.
Reverse speed: Zero to
Max.
Note: Press foot pedal
to change mode and
take over from control
panel.
Machine Runs @ 3f/m.
(Automatic override from
high to low voltage)
Machine still remains at low voltage
speed of 3f/m.
Steps required to run at (various speed):
The operator will have two choices,
Reverse Mode
Press Reverse
Push button switch.
Choice A:
1. Release foot pedal to stop machine.
2. Press foot pedal again to start
machine at original preset control panel
knob speed (pot).
Choice B:
1. Press and hold “Run” push button
switch on the control panel while foot is
still on pedal.
2. Release foot pedal.
3. Adjust speed using “speed knob”
© 2009 General Binding Corporation an ACCO Brands CO.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
OPERATING INSTRUCTIONS
Film Loading & Threading
The top and bottom rolls of laminating film must be
of the same width and be present simultaneously. A
Small amount of adhesive will “squeeze out” during
Lamination. Hardened adhesive deposits can damage
the heat rollers.
CAUTION:
Adhesive will deposit on the rollers if:
•
•
•
Only one roll is used.
Different widths of rolls are loaded together.
Either roll is loaded adhesive side against a heat
roller.
Polyester surface
•
One or both rolls of film are allowed to run
completely off its core.
The adhesive side of the film is on the inner side of
the web (Fig. 17A & B). The shiny side of clear film
must contact the heat rollers. The dull side of the
film contains the adhesive. Use extreme caution
when loading delustered (matte) film as both sides
appear dull.
Always change the top and bottom supply rolls at the
same time. Near the end of each roll of GBC
laminating film is a label stating “Warning-End of
Roll”. The appearance of this label on either the top
or bottom roll requires that new rolls of film be
installed as soon as the item presently being
laminated completely exits the rear of the laminator.
Polyester surface
FIGURE 17
Do not introduce any additional items into the
laminator when the warning label is visible.
To load a roll of film: (Fig. 18)
1. Pull the swing out shaft clevis pin up.
2. Swing shaft outward.
1
4
3. Slide the roll of film onto the film shaft ensuring
Adhesive side is out.
5
2
4. Push the film shaft back into the film shaft
Support saddle.
5. Push the clevis pin down.
6. Center the roll of film.
6
=
3
FIGURE 18
© 2009 General Binding Corporation an ACCO Brands CO.
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
Webbing Thermal Film Using Threading Card
THERMAL
LAMINATE
CAUTION: The laminator rollers will be hot and
can burn you. For pressure sensitive film (PSA),
refer to the section titled
WEBBING: USING FILM THREADING CARD
FOR PSA FILM.
1. Turn the Main Power ON
/OFF
to On.
2. Set top and bottom temperature with regards to the
film type used.
3. Ensure no brake tension is applied to the film shafts.
FIGURE 19
4. Pull the top roll film down under the upper idler bar
and allow to drape over the top heat roller (Fig. 19)
5. Pull the lower film behind the lower idler bar, Lower
the table Pull Film up towards the film draped over
the top heat roller and adhere the Lower Film to the
upper Film (Fig. 20).
THERMAL
LAMINATE
6. Pivot the table back to its feeding position while
ensuring the threading card is on top of the feed table
(Fig. 21).
7. Use a threading card to push the two materials into
the heat roller nip.
8. Lower the main roller to initial contact with the
threading card.
9. Ensure forward is selected for Motor direction and
Press the Foot Switch
THERMAL
LAMINATE
10.From the rear of the machine, guide the web over the
chill idler, if installed, and through the pull rollers.
FIGURE 20
11.Once the web has entered the pull roller nip, lower
the pull roller nip. Adjust unwind film tension; use as
little tension as possible to get smooth output.
12.Once the threading card has completely exited the
pull rollers, press the stop (
) button.
THERMAL
LAMINATE
13.Now refer to the section entitled START
LAMINATING.
THERMAL
LAMINATE
FIGURE 21
© 2009 General Binding Corporation an ACCO Brands CO.
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
Webbing PSA Film/Mount Adhesive Using
Threading Card
The laminator should be cool to the touch before
Proceeding.
1. Turn the Power ON
/OFF
to On
2. Load the rolls of film as illustrated in (Fig. 22).
Ensure no brake tension is applied to the film
shafts.
3. Pull the top roll of film down under the idler bar
and up to the upper front rewind tube.
4. Place one piece of masking tape in the center of
the film and secure to the rewind tube.
5. Make two full wraps around the rewind tube,
and then score the laminate without cutting the
release liner. Pull the laminate down allowing it
to drape over the upper roller (Fig. 22).
FIGURE 22
6. Pull the mount adhesive up towards the film
draped over the upper heat roller (Fig. 23).
REWIND TUBE
PSA
Film
7. Stick the mount adhesive to the exposed
adhesive of the upper role.
8. Insert the table back to its feeding position
while ensuring the threading card is on top of
the feed table (Fig. 24).
9. Use a threading card to push the two materials
through the heat roller nip
Mount
Adhesive
10.Lower the main heated roller to bring the main
roller into initial contact with the threading card.
Ensure front is selected and press the foot
switch.
11.From the rear of the machine, guide the web
over the chill idler, if installed, and through the
pull rollers. Once the web has entered the pull
roller nip, close the pull roller nip –
FIGURE 23
12.Press the stop ( ) button when the threading
card has completely exited the pull rollers and
adjusts the film web tension using as little
tension as possible.
PSA
Film
13.Now refer to the section titled START
LAMINATING.
CHILLED ROLLER
HEAT ROLLER
Mount
Adhesive
FIGURE 24
© 2009 General Binding Corporation an ACCO Brands CO.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
Start Laminating
1. At this point you should have your laminator
webbed with the appropriate material for your
application.
2. The feed table should be in the normal operating
position.
3. Close the main and Pull roll nips. Rollers should
be closed.
4. Speed is set to 3 or less and front () motor
direction is selected.
5. Press the start ( ) button.
6. Set main roller pressure between 40% – 60% for
laminating by turning the main roll lift handle.
FIGURE 25
CAUTION: If using PSA film, an air pocket may
form between the main rollers and pull rollers.
Raise the pull rollers to allow the air Pocket to
pass.
7. Make any necessary film brake tension
adjustments, pull/main roller pressure, and
clutch and/ or rewind brake tension adjustments.
8. Position the item to be laminated on the feed
table.
9. Align the leading edge of the item parallel to the
heat roller nip (Fig. 25).
10.Use both hands to force the image outward and
slowly push inward toward the nip of the heat
rollers (Fig. 26).
CAUTION: Avoid forcing the image into the
main roller nip as this action will cause the
corners of the leading edge to buckle and create a
wave.
FIGURE 26
© 2009 General Binding Corporation an ACCO Brands CO.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
Method for Tacking New Film to Existing Film
(1)
The following describes a method for loading film
whereby the existing film present on the heat
rollers may be used in place of the threading card
to draw the new film through the laminator. The
adhesive of the existing film must be tacky or
liquefied. Leading edges of the new film will be
overlapped onto the tacky adhesive of the old film.
The existing film and the new film will be pulled
through the laminator together.
(2)
(2)
CAUTION: Do not cut yourself
A
.......a PSA film or mount adhesive
CAUTION: Be careful not to cut any of the
rollers!
FIGURE 27
1. Cut (1) remaining top film web between the
idler bar and heat roller. Cut (2) the film web
between the lower film supply and the idler
bar (FIGURE 27).
CAUTION: Be careful not to cut any of the
rollers!
2. Remove the feed table.
3. Do not allow the adhesive side of the film to
contact the heat or pull rollers. Liquefied or
tacky adhesive deposited on heat rollers will
require the rollers to be cleaned per the section
tilted.
4. Replace both the top and bottom rolls of film
with new rolls. Ensure the adhesive side is
facing out.
B
.......a PSA film or mount adhesive
FIGURE 28
5. Pull the film around the idler bars, with the
exception of PSA mounting adhesives without
a release liner.
6. Tack the new film to the existing film on the
heat rollers. For PSA film, attach the release
liner to the rewind tube
7. Use the footswitch to advance the film into the
heat roller nip.
8. Observe the film being pulled through the
laminator to assure that the remaining existing
film and the new films are advancing
concurrently. Any separation between the
films will require stopping the motor
immediately and the situation corrected.
9. Press STOP ( ) once the newly threaded film
has completely exited the pull rollers.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
To unweb the laminator
(2)
Unweb the laminator if you are changing film
widths, cleaning the rollers or have finished using
the machine for the day.
(1)
CAUTION: Do not cut yourself
(3)
1. Using a slitter, cut (1) the output from the web
(Fig. 28).
(2)
2. Cut (2) remaining top film web between the
idler bar and heat roller. PSA film cut the
release liner too.
.......a PSA film or mount adhesive
3. Cut (3) the film web between the lower film
supply and the idler bar (Fig. 28).
FIGURE 28
CAUTION: Be careful not to cut any of the
rollers!
4. Remove the feed table.
5. Gap the main rollers and pull rollers.
PULL WEB
6. Carefully grab hold of the web (top and bottom
film), from the back operating position and pull
towards you (Fig. 29).
7. Do not allow the adhesive side of the film to
contact the heat or pull rollers.
Clearing a Film Jam (Wrap-up)
Film jams (wrap-ups) may occur if the film is loaded
backwards or if the area at which film exits the
equipment is blocked. The film, when jammed,
wraps around the heat rollers or pulls rollers during
webbing if webbing, if a Thread Card is not used.
FIGURE 29
To clear a jam:
1. Immediately stop the laminator by pressing
STOP ( ).
2. Set motor direction to rear.
3. Use the footswitch to reverse the web until the
wrap up is clear.
4. Raise the main roller and pull rollers.
5. Manually guide the web from the main rollers
and pull rollers.
6. Once the film jam has been cleared, lower the
main roller and pull rollers.
7. Refer to the section titled START
LAMINATING.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
APPLICATIONS
Tips for Pre Coating Boards
MOUNT
ADHESIVE
1. Load the laminator as illustrated in (Fig. 30).
Remove chill idler.
LEADER BOARD
TRAILOR BOARD
2. The width of the roll should not exceed the
width of the board by more than 1/2 in. (1.3
cm).
3. Use a leader board to set the main roller and
pull roller pressure prior to webbing.
BOARDS
4. Use a leader board to start the run and a trailer
board to finish the run.
5. Using the pull rollers will allow you to leave
gaps between boards.
6. If not using the pull rollers, have the boards
nearby to butt end to end during feeding.
FIGURE 30
Tips for Mounting Pre Coated Boards
1. Use a leader board to set the main roller
pressure prior to mounting the image.
IMAGE
2. Ensure the chill idler is removed and the rear
slitter is to one side.
RELEASE LINER
3. Do not stop once you have started the mounting
process through the machine. (Fig. 31)
PRE-COATED BOARD
Note: This application can also be performed from
the rear operating position. Reference Fig. 34 for
Illustration.
Tips for Single Sided lamination
FIGURE 31
1. Load the laminator as illustrated in Fig. 32.
2. Use kraft paper for one-sided lamination When
ever the items to be laminated are narrower than
the film you are using.
MOUNT
ADHESIVE
RELEASE LINER FROM PSA FILM
3. If not using kraft paper, use a scrap piece to
finish the run or you will have adhesive on your
rollers.
OUTPUT
IMAGE
4. For high volume runs, use Kraft paper and the
lower rear rewind for roll to roll operation.
5. Running the web over the chill idler may
improve the Flatness of the output.
ROLL TO ROLL OPTION
KRAFT
PAPER
OPTION
6. A little heat,125 degree F (52 degree C),may
help eliminate silvering effects associated with
PSA films.
FIGURE 32
© 2009 General Binding Corporation an ACCO Brands CO.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
Tips for Creating a Decal
THERMAL
OR PSA
FILM
RELEASE LINER FROM PSA FILM
1. Load the laminator as illustrated in Fig. 33.
2. The over laminate may be PSA or thermal type.
OUTPUT
3. If using thermal type, pay attention to the Poly-
in/Poly-out rule.
IMAGE
4. Run a test material prior to running the actual
image to ensure flat output.
MOUNT
ADHESIVE
5. Use minimal brake tension to achieve quality
output.
ROLL TO ROLL OPTION
6. Do not web the PSA mount adhesive around the
lower web idler.
FIGURE 33
Tips for mounting a Decal
1. Use a leader board to set the pull roller pressure
Prior to mounting the image.
2. The image should not exceed the width of the
board by more than 1 in. (2.54 cm) per side.
DECAL
RELEASE LINER
BOARD
3. Tack about 1 in. (2.54 cm) of the leading edge
of the decal to the leading edge of the board.
4. When tacking the leading edge, start in the
center and work to the sides.
5. Use a board that exceeds the size of the decal if
inexperienced in the mounting application.
Note: This application can also be performed from
the front operating position. Reference Fig. 31 for
Illustration.
FIGURE 34
Tips for Thermal Encapsulation
THERMAL
FILM
1. Load the laminator as illustrated in Fig. 35
Poly-in film is used for illustration purpose.
IMAGE
2. Refer to section entitled FILM LOADING &
THREADING for Poly-out film.
OUTPUT
3. Always use two rolls of film the same width.
4. Use minimal brake tension to achieve flat
output.
5. Increase speed gradually to maintain the
activating temperature required for the laminate
you are using.
ROLL TO ROLL OPTION
THERMAL
FILM
6. Length and width of image, ink coverage and
paper type may affect the temperature and speed
recommended in the SPEED/ TEMPERATURE
GUIDE.
FIGURE 35
© 2009 General Binding Corporation an ACCO Brands CO.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
Tips for AccuShield
THERMAL
FILM
IMAGE
1. Load the laminator as illustrated in Fig. 36.
OPTIONAL
SEPERATOR BAR
2. You must have the Separator bar option to
accurately run this material. See your Sales Rep
for ordering the Separator Bar.
OUTPUT
3. Set Top Temp to 280*F(135*C) and a speed
setting no greater than 4.
4. Liner rewind tension will be greater than normal
operating standard
ROLL TO ROLL OPTION
5. To prevent some adhesive adhering to the rollers,
you may choose to use a roll of craft paper for a
Carrier.
KRAFT
PAPER
OPTION
Use the blank space below and blank diagrams to
FIGURE 36
Note your tips and web paths for your Special
applications.
TIPS FOR CUSTOM APPLICATION #1 (Fig. 37)
1.
2.
3.
4.
TIPS FOR CUSTOM APPLICATION #2 (Fig. 38)
CUSTOM WEB PATH #1
1.
2.
3.
4.
5.
FIGURE 37
CUSTOM WEB PATH #2
FIGURE 38
© 2009 General Binding Corporation an ACCO Brands CO.
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
SPEED / TEMPERATURE CONTROL
This is only a general reference guide. Different settings may be suitable as the warm up time, lamination time and materials
change.
Factors that may affect the speed and temperature parameters;
1. Image length
2. Image width and ink coverage.
3. Ink coverage
4. Paper type
5. Laminate thickness
6. Operating environment
7. Condition of the rollers
8. Line voltage (effects heaters)
9. Using cooling features.
You may have to adjust temperature or speed depending on stock finish, thickness *Turn heat off when not in use.
THE ART OF LAMINATION
BASIC RULES
•
•
Do not attempt to laminate abrasive or metal Objects such as staples, paper clips and glitter, as they may damage
the heat or pull rollers.
Do not force items into the nip area of the heat rollers. An item that is not easily drawn into the laminator by the
heat rollers is probably too thick to laminate.
•
•
Wrinkles may result if an attempt is made to reposition an item once it has been grasped by the heat rollers.
Do not stop the laminator before an item has completely exited the pull rollers. Even a momentary stop will cause
a mark (heat line) on the laminated item.
Good, consistent lamination is a result of combining proper heat, tension and dwell time. Dwell time is controlled by the
speed of the motor and is defined as the amount of time the material to be laminated is compressed between the heat rollers.
As a general rule, thicker items and film need to run at slower speeds because they extract more heat from the rollers at a
quicker rate. Setting the speed control at slower settings gives the laminator longer dwell time thus allowing proper
lamination of thick items. Thinner items, such as standard copier paper (20 lb. bond) and tissue paper, extract less heat from
the rollers and can be run at faster speeds.
FILM TENSION
Proper film tension, known as brake tension, is the minimum amount required to eliminate wrinkles in the finished item. The
film should be taut. A properly adjusted roll of film should not require excessive force to turn by hand.
Film tension should be enough to introduce a minor amount of drag as the film unrolls. Insufficient tension causes wrinkles,
while too much tension causes stretching (necking). Uneven tension between the top and bottom rolls creates curl. Too
much upper tension creates upward curl while too much bottom tension causes downward curl.
Adjustment of the pull roller clutch may be necessary if after adjusting unwind and rewind brake tensions do not improve
your output quality.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
Heat
The “READY” indicator may extinguish if the speed
is set too fast for the material being laminated. Either
lower the speed setting or press STOP ( ) and wait
until the “READY” indicator illuminates. Operation
of the laminator for more than thirty minutes at a
time may necessitate a lower speed setting. It is
recommended that, during periods of long runs, the
items being laminated are alternated between thick
and thin. Do not combine thick and thin items at the
same time, as this will result in a poor edge seal
around the thinner material. If you are unsure that the
laminator is set at the proper speed for the item to be
laminated, run a test piece (scrap) of the same or
similar material through the Laminator. This
procedure is recommended because rotating the heat
roller prior to lamination will more evenly distribute
the heat.
- A -
- B -
FIGURE 39
Make speed adjustments if necessary.
Output
1. “D” waves in the image (Fig. 39 A).
•
•
Check paper tension.
Paper may be damp or not dry.
2. “D” waves in the laminate (Fig. 39 B).
•
•
Check main roller pressure.
Check pull roller pressure.
- A -
- B -
3. Straight waves in output (Fig. 40 A).
FIGURE 40
•
Check operational settings for materials
being used.
•
Check clutch tension.
4. Indent waves in output after pull rollers
•
•
•
•
Insufficient cooling time.
Output was handled prior to cooling.
Use cooling feature if not on.
Machine was stopped on print.
5. Angled waves in the output
•
•
•
•
•
Main air Supply setting
Check main Roller Pressure.
Check main roller pressure.
Check pull roller pressure.
Check for Paper Tension.
- A -
- B -
FIGURE 41
© 2009 General Binding Corporation an ACCO Brands CO.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
MAINTENANCE
Caring For The GBC 2064WF-1 Laminator
GBC offers Cleaning kits as well as Extended Maintenance Agreements.
Contact your local GBC Service Representative or your dealer/distributor for additional information. The only maintenance required by the
operator is to periodically clean the heat rollers and schedule semi annual maintenance checks. The following procedure will help keep the
heat rollers free of adhesive that has been deposited along the edge of the laminating film. Proper alignment of the rolls of film reduces the
amount of “squeeze out”.
WARNING: Do not attempt to laminate adhesives marked “Flammable”.
Do not laminate glitter and/ or metallic items. Damage to the rollers may result.
WARNING: Do not apply any cleaning fluids or solvents to the rollers. Some solvents and fluids could ignite on heated
rollers.
WARNING: Never clean rollers with sharp or pointed objects.
Hardened adhesive deposits on the rollers can cause damage to the rollers. Rotate the rollers at the lowest
speed setting on the control panel.
CAUTION: THE FOLLOWING PROCEDURE IS PERFORMED WHILE THE LAMINATOR IS HOT. USE
EXTREME CAUTION.
1.
Remove the film from the laminator following the Procedure outlined in steps 1 through 6 of the section entitled TO UNWEB
THE LAMINATOR.
2.
3.
4.
5.
Preheat the laminator until the “READY” indicator illuminates.
Tilt the feed table.
Rub the top and bottom heat rollers with a 3M™ Scotch-Brite™ pad. DO NOT USE METAL SCOURING PADS!
Use the footswitch to rotate the lower heat/ pull roller to an unclean portion. The upper heat/ pull rollers are free spinning.
Continue this process until the complete surfaces of both rollers are clean.
6.
Refer to the beginning of the section entitled OPERATING INSTRUCTIONS to web your laminator.
NOTE: Do not use metal scouring pads to clean the rollers.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
TROUBLE SHOOTING GUIDE
SYMPTOM
POSSIBLE CAUSE
CORRECTIVE ACTION
The control panel display does not
Laminator not connected to
Insert attachment plug into
receptacle
illuminate when POWER ON/OFF electrical supply
is in the ON, marked “I”, position
Blown out fuse.
Check fuses.
Heat rollers do not turn when I
Feed table not properly installed.
Tilt feed table and properly replace
it.
Press the RUN ( ) button.
Pull E-Stop button
Pull out on the E-STOP push
button.
Heat rollers only turn if I use the
“Footswitch”.
Photo eye is blocked.
Disengage the footswitch mode.
Clear nip area.
Laminated items exhibit curling.
Tension between the top and
bottom film. Roll is unequal.
Tension on top or bottom roll of
film is too film is too loose.
Bottom film roll may be
Adjust tension per section FILM
TENSION.
Adjust tension per section FILM
TENSION.
Make sure bottom roll of film is
around idler bar and that is the
normal operation position.
Release heat and pull roller
pressure, align the rolls of film.
Adhesive (matte) side of laminate
film may be against the heat rollers.
Unweb and reload the film
properly.
improperly loaded.
Adhesive deposited on heat rollers. Top and bottom film webs not
aligned
Laminate improperly loaded.
Unsatisfactory adhesion of
laminate.
Speed setting too fast for type of
material being laminated
Insufficient heat
Lower speed setting.
Wait for “READY” indicator to
appear in the control panel display.
Adhesive side of film must be
facing away from the heat rollers.
Bottom roll of film not threaded
behind the idle bar.
Laminate improperly loaded
Heat rollers require cleaning.
Laminated item unsuitable for
adhesion.
Clean heat rollers per procedure in
section CARING FOR THE GBC
2064WF-1 WF LAMINATOR.
Item may be dirty or may have non
porous surface that is extremely
difficult to laminate.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
GBC 2064WF-1
Operation Manual
SERVICE AGREEMENT
GBC’s Equipment Maintenance Agreement will insure the quality performance and long life built into your laminator.
A service charge for travel time, labor and parts may be incurred for each out of warranty service call. GBC’s Equipment Maintenance
Agreement
Decreases these expenses and protects your valuable investment. GBC offers several types of agreements to suit your needs and budget. To
contact
GBC write to:
ACCO Brands Inc.
IN CANADA:
GBC NATIONAL SERVICE
49 RAILSIDE ROAD
DON MILLS, ONTARIO
M3A 1B3
300 Tower Parkway
Lincolnshire, IL 60069 U.S.A.
© 2009 General Binding Corporation an ACCO Brands CO.
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
|