LaCie 319 LCD Monitor
User’s Manual
How To Use This Manual
How To Use This Manual
In the toolbar:
Previous Page / Next Page
Go to Contents Page / Go to Precautions Page
Printing:
While optimized for onscreen viewing, the pages of this manual are formatted for printing on 8 1/2” x 11” and A4 sized
paper, giving you the option to print the entire manual or just a specific page or section.
To Exit:
From the Menu bar at the top of your screen, select: File > Quit.
Icons Used In This Manual
These icons describe the type of information being given:
Important Info: This icon refers to an important step that must be followed.
i
Tech Note: This icon refers to tips to help maximize performance.
N
T
Caution! This icon indicates a potential hazard, and gives tips on how to avoid them.
LaCie 319 LCD Monitor
User’s Manual
Foreword
page 3
Copyrights
Copyright © 2004/2005 LaCie. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent
of LaCie.
Changes
The material in this document is for information only and subject to change without notice. While reasonable efforts have been made in
the preparation of this document to assure its accuracy, LaCie assumes no liability resulting from errors or omissions in this document, or
from the use of the information contained herein. LaCie reserves the right to make changes or revisions in the product design or the
product manual without reservation and without obligation to notify any person of such revisions and changes.
FCC Statement:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try and correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Use only shielded cables to connect I/O devices to this equipment.
LaCie 319 LCD Monitor
Tested To Comply
With FCC standards
FOR HOME OR OFFICE USE
Caution! Modifications not authorized by the manufacturer may void the user’s authority to operate this device.
Caution! A shielded-type power cord is required in order to meet FCC emission limits and also to prevent
interference to the nearby radio and television reception. It is essential that only the supplied power cord be used.
LaCie 319 LCD Monitor
User’s Manual
Foreword
page 4
Canada Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
CFC-UCL: InBfeoarrsmthaetiCo-nUL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
1.
Use the attached specified cables with the LaCie 319 color monitor so as not to interfere with
radio and television reception.
(1) The power supply cord you use must have been approved by and comply with the safety standards of U.S.A. and meet the
following condition.
Power supply cord
Length
Non shield type, 3-conductor
2.0 m
Plug shape
U.S.A
(2) Please use the supplied shielded video signal cable, 15-pin mini D-SUB to DVI-A cable or DVI-D to DVI-D cable.
Use of other cables and adapters may cause interference with radio and television reception.
2.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet, prepared by the Federal Communications Commission, helpful:
“How to Identify and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government
Printing Office, Washington, D.C., 20402, Stock No. 004-000-00345-4.
Manufacturer’s Declaration for CE Certification
We, LaCie, solemnly declare that this product conforms to the following European standards:
Class B EN60950, EN55022, EN50082-1, EN61000-3-2
With reference to the following conditions:
73/23/EEC Low Voltage Directive
89/336/EEC EMC Directive
LaCie 319 LCD Monitor
User’s Manual
Precautions
page 5
Recommended use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP AND USING
THE LaCie 319 LCD COLOR MONITOR:
•
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside and opening or removing covers may expose
you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel.
Do not spill any liquids into the cabinet or use your monitor near water.
•
•
Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage points, which can be
harmful or fatal or may cause electric shock, fire or equipment failure.
Do not place any heavy objects on the power cord. Damage to the cord may cause shock or fire.
Do not place this product on a sloping or unstable surface, as the monitor may fall, causing serious damage.
Do not place any objects onto the monitor and do not use the monitor outdoors.
The inside of the fluorescent tube located within the LCD monitor contains mercury. Please follow the bylaws or rules of
your municipality to dispose of the tube properly.
•
•
•
•
•
•
•
Do not bend power cord.
Do not use monitor in high temperatured, humid, dusty, or oily areas.
Do not cover vent on monitor.
Immediately unplug your monitor from the outlet and refer servicing to qualified personnel under the following conditions:
•
•
•
•
•
•
•
•
When the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the monitor.
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet damaged.
If the monitor does not operate normally by following operating instructions.
If glass is broken, handle with care.
If monitor or glass is broken, do not come in contact with the liquid crystal and handle with care.
Allow adequate ventilation around the monitor so that heat can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources. Do not put anything on top of monitor.
The power cable connector is the primary means of detaching the system from the power supply. The monitor should be
installed close to a power outlet which is easily accessible.
•
•
•
Handle with care when transporting. Save packaging for transporting.
Image Persistence: Please be aware that LCD Technology may experience a phenomenon known as Image Persistence.
Image Persistence occurs when a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT
monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time
should be avoided. To alleviate image persistence, turn off teh monitor for as long as the previous image was displayed. For
example, if an image was on the monitor for one hour, the monitor should be turned off for one hour to erase the image.
LaCie 319 LCD Monitor
User’s Manual
Precautions
page 6
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT'S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET.DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
Caution:
When operating the LaCie 319 LCD Monitor with a 220-240V AC power source in Europe, use the power cord pro-
vided with the monitor.
In the UK, a BS approved power cord with a moulded plug has a Black (five Amps) fuse installed for use with this
equipment.
If a power cord is not supplied with this equipment please contact your supplier.
When operating the LaCie 319 LCD Monitor with a 220-240V AC power source in Australia, use the power cord
provided with the monitor. If a power cord is not supplied with this equipment please contact your supplier.
For all other cases, use a power cord that matches the AC voltage of the power outlet and has been approved by
and complies with the safety standard of your particular country.
Declaration
Declaration of the Manufacturer
We hereby certify that the color monitor LaCie 319 is in
and marked with
compliance with
Council Directive 73/23/EEC:
– EN 60950-1
Council Directive 89/336/EEC:
– EN 55022
LaCie Group
17, rue Ampère
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
91349 Massy Cedex
France
LaCie 319 LCD Monitor
User’s Manual
Precautions
page 7
CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN
REDUCE EYE, SHOULDER AND NECK FATIGUE. CHECK THE
FOLLOWING WHEN YOU POSITION THE MONITOR:
•
•
For optimum performance, allow 20 minutes for warm-up.
Adjust the monitor height so that the top of the screen is at or slightly below eye
level.Your eyes should look slightly downward when viewing the middle of the
screen.
•
•
•
Position your monitor no closer than 40 cm and no further away than 70 cm
from your eyes. The optimal distance is 50 cm.
Rest your eyes periodically by focusing on an object at least 20 feet away. Blink
often.
Position the monitor at a 90° angle to windows and other light sources to
minimize glare and reflections. Adjust the monitor tilt so that ceiling lights do not
reflect on your screen.
•
•
•
•
•
If reflected light makes it hard for you to see your screen, use an anti-glare filter.
Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any cleaning solution or glass cleaner!
Adjust the monitor’s brightness and contrast controls to enhance readability.
Use a document holder placed close to the screen.
Position whatever you are looking at most of the time (the screen or reference material) directly in front of you to
minimize turning your head while you are typing.
•
•
Avoid displaying fixed patterns on the monitor for long periods of time to avoid image persistence (after-image
effects).
Get regular eye checkups.
Ergonomics
To realize the maximum ergonomics benefits, we recommend the following:
•
•
•
•
•
•
Adjust the Brightness until the background raster disappears.
Do not position the Contrast control to its maximum setting.
Use the preset Size and Position controls with standard signals.
Use the preset Color Setting.
Use non-interlaced signals with a vertical refresh rate between 60-75 Hz.
Do not use primary color blue on a dark background, as it is difficult to see and may produce eye fatigue to
insufficient contrast.
LaCie 319 LCD Monitor
User’s Manual
Environmental Regulations
page 8
Congratulations! You have just purchased a TCO’99 approved and labeled product! Your choice has
provided you with a product developed for professional use. Your purchase has also contributed to
reducing the burden on the environment andto the further development of environmentally adapted elec-
tronics products.
Why do we have environmentally labeled computers?
In many countries, environmental labeling has become an established method for encouraging the adaptation of goods and
services to the environment. The main problem, as far as computers and other electronics equipment are concerned, is that
environmentally harmful substances are used both in the products and during the manufacturing. Since it has not been possi-
ble for the majority of electronics equipment to be recycled in a satisfactory way, most of these potentially damaging sub-
stances sooner or later enter Nature. There are also other characteristics of a computer, such as energy consumption levels,
that are important from the viewpoints of both the work (internal) and natural (external) environments. Since all methods of
conventional electricity generation have a negative effect on the environment (acidic and climate-influencing emissions,
radioactive waste, etc.), it is vital to conserve energy. Electronics equipment in offices consume an enormous amount of
energy since they are often left running continuously.
What does labeling involve?
This product meets the requirements for international and environmental labeling of personal computers. The requirements
cover a wide range of issues, including: environment, ergonomics, usability, emission of electrical and magnetic fields, energy
consumption and electrical and fire safety. The environmental demands concern restrictions on the presence and use of heavy
metals, brominated and chlorinated flame retardants, CFCs (freons) and chlorinated solvents, among other things. The product
must be prepared for recycling and the manufacturer is obliged to have an environmental plan which must be adhered to in
each country where the company implements its operational policy. The energy requirements include a demand that the com-
puter and/or display, after a certain period of inactivity, shall reduce its power consumption to a lower level in one or more
stages. The length of time to reactivate the computer shall be reasonable for the user. Labeled products must meet strict envi-
ronmental demands, for example, in respect of the reduction of electric and magnetic fields, physical and visual ergonomics
and good usability.
Environmental Requirements
Flame retardants
Flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of
fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants
contain bromine or chloride and these are related to another group of environmental toxins, PCBs, which are suspected to
give rise to severe health effects, including reproductive damage in fisheating birds and mammals, due to the bioaccumula-
tive* processes. Flame retardants have been found in human blood and researchers fear that disturbances in fetus develop-
ment may occur. Plastic components weighing more than 25 grams must not contain flame retardants with organically bound
chlorine and bromine. Flame retardants are allowed in the printed circuit boards since no substitutes are available.
LaCie 319 LCD Monitor
User’s Manual
Environmental Regulations
page 9
Lead**
Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher
doses, causes lead poisoning. Requirements permit the inclusion of lead since no replacement has yet been
developed.
Cadmium**
Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium
damages the nervous system and is toxic in high doses. Requirements state that batteries, the color-generating
layers of display screens and the electrical or electronics components must not contain any cadmium.
Mercury**
Mercury is sometimes found in batteries, relays and switches, Mercury damages the nervous system and is toxic in high
doses. Requirements state that batteries may not contain any Mercury. It also demands that no mercury is present in any of
the electrical or electronics components associated with the display unit.
CFCs (freons)
CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the
ozone layer in the stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of
skin cancer (malignant melanoma). The relevant requirement; Neither CFCs nor HCFCs may be used during the manufactur-
ing and assembly of the product or its packaging.
*Bio-accumulative is defined as substances which accumulate within living organisms.
**Lead, Cadmium and Mercury are heavy metals which are bio-accumulative.
LaCie 319 LCD Monitor
User’s Manual
Specifications
page 10
Specifications
LaCie 319
Technology
S-IPS
19’’
1280x1024
0.29
Diagonal
Resolution
Dot pitch
48.2cm
Gamut
72% NTSC
100% EBU
Gamma Correction
Luminance
10-bit
270 cd/m2
600:1
18 ms
178°
Contrast Ratio
Response Time
Viewing Angles
Connections
VGA + DVI-D + DVI-I
Power Consumption
In Power Save Mode
Weight
48 W
<2W
9.7 kg
Weight without stand
Ergonomy
6.3 kg
Pivot 90°*, Tilt, Swivel, Height-adjustable,
Compatible with VESA 100 support solutions
CE, FCC-B, TÜV-Ergonomie, TÜV-GS, TCO99, EnergyStar,
C-Tick, GOST-R, c-UL, UL, VCCI-B, VESA DDC 2B, DDC-CI
US : 3-year limited
Certifications
Warranty
Europe : 3-year advance swap
* On Macintosh portrait mode requires high end graphic board such as ATI Radeon x800
LaCie 319 LCD Monitor
User’s Manual
1. Package Contents
page 11
1. Package Contents
Your LaCie 319 LCD monitor should ship with the following:
1
LaCie 319 LCD Monitor with tilt/swivel/pivot/height adjust stand
Power cords
1
2
3
4
5
6
7
8
Video signal cable (15-pin mini D-SUB male to DVI-A)
Video signal cable (DVI-D to DVI-D cable)
Cable cover
2
CD ROM (includes complete User’s Manual in PDF format)
Pivot Software CD
3
blue eye pro calibration Software CD
4
5
6
7
8
Important Info: Please keep your box. In the event that he LaCie 319 LCD Monitor should need to be repaired or
serviced, it must be returned in its original packaging.
i
LaCie 319 LCD Monitor
User’s Manual
2. Quick Start
page 12
2. Quick Start
To attach the LaCie LCD Monitor to your system, follow these instructions:
1. Turn off the power to your computer.
2. For the PC or MAC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your
system (Figure A.1). Tighten all screws.
For the PC with Analog output: Connect the 15-pin mini D-SUB to DVI-A signal cable to the connector of the display
card in your system (Figure A.2).
For the MAC: Connect the Macintosh cable adapter to the computer, then attach the 15-pin mini D-SUB signal
cable to the Macintosh cable adapter (Figure B.1).
Macintosh
Cable Adapter
Figure A.1
Figure A.2
Figure B.1
(not included)
NOTE: Some Macintosh systems do not require a Macintosh cable adapter.
3. Connect the DVI signal cable to the connector on the back of the monitor. Place the video signal cable (Figure C.1).
Connect only either VGA or DVI to input 2.
NOTE: Incorrect cable connections may result in irregular operation, damage display quality/components of LCD module
and/or shorten the module’s life.
Collect cables and keep them in the stand with attached cable cover. The cable cover can be attached on the front or
back side of Tilt Stand (Figure C.1, C.2).
Please check Tilt, Rise and Lower monitor screen and screen rotation when you manage cables.
4. Connect one end of the power cord to the AC inlet on the back of the monitor and the other end to the power outlet
(Figure C.1).
NOTE: Please refer to Caution section of this manual for proper selection of AC power cord.
5. The Vacation Switch on the left side of the monitor must be turned on. Turn on the monitor with the front power button
(Figure D.1).
NOTE: The Vacation Switch is a true on/off switch. If this switch is on the OFF position, the monitor cannot be turned on
LaCie 319 LCD Monitor
User’s Manual
2. Quick Start
page 13
using the front button. DO NOT switch on/off repeatedly.
NOTE: For the MAC with digital output: Before turning on the MAC, the DVI Input mode must be set to DIGITAL in
“DVI SELECTION” of OSM by pressing “SELECT” button then “CONTROL” button when the DVI signal cable is
connected to the DVI-I connector (Input1) of the monitor. Otherwise the MAC may not turn on.
6. Turn on the computer. No-touch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup for
most timings. For further adjustments, use the following OSM controls:
• Auto Contrast (Analog input only)
• Auto Adjust (Analog input only)
Refer to the Controls section of this User’s Manual for a full description of these OSM controls.
NOTE: If you have any problems, please refer to the Troubleshooting section of this User’s Manual.
LaCie 319 LCD Monitor
User’s Manual
3. Your LaCie 319 LCD Monitor
page 14
INPUT1
INPUT2
INPUT1
INPUT2
Figure C.2
Figure C.1
Vacation
Switch
Power Button
Figure D.1
Raise and Lower Monitor Screen
The monitor may be raised or lowered in either Portrait or Landscape mode.
To raise or lower screen, place hands on each side of the monitor and gently lift or lower to the desired height (Figure RL.1).
Figure RL.1
Screen Rotation
Before rotating, the screen must be raised to the highest level to avoid knocking the screen on the desk or pinching your
fingers.
To raise the screen, place hands on each side of the monitor and lift up to the highest position (Figure RL.1).
To rotate screen, place hands on each side of the monitor screen and turn clockwise from Landscape to Portrait or
counterclockwise from Portrait to Landscape (Figure R.1).
To rotate OSM menu between landscape and portrait, refer to “Controls” section, “OSM ROTATION” function. (Figure R.1)
NOTE: If the screen is rotated counterclockwise, the tilt function is not available. Rotate the screen 90° clockwise until you hear
one click.
Figure R.1
LaCie 319 LCD Monitor
User’s Manual
3. Your LaCie 319 LCD Monitor
page 15
Tilt
Swivel
Grasp top and bottom sides of the monitor screen with your
Grasp both sides of the monitor screen with your hands
hands and adjust the tilt as desired (Figure TS.1).
and adjust the swivel as desired (Figure TS.2).
Figure TS.1
Figure TS.2
NOTE: Handle with care when tilting the monitor screen.
NOTE: If the tilt function is not available, rotate the screen 90° clockwise until you hear one click.
Remove Monitor Stand for Mounting
To prepare the monitor for alternate mounting purposes:
1. Disconnect all cables.
2. Place hands on each side of the monitor and lift up to the highest position.
3. Place monitor face down on a non-abrasive surface. (Place the screen on a 36 mm platform so that the stand is parallel
with the surface) (Figure S.1).
36 mm
Figure S.1
4. Remove the two top screws connecting the monitor to the stand (Figure S.2). Turn the stand to 180° counterclockwise
(you will hear two clicks). Remove the screws from the bottom (Figure S.3) and lift off the stand. The monitor is now ready
for mounting in an alternate manner.
5. Reverse this process to reattach stand: tighten the two bottom screws, turn stand 180° counter clockwise (you will hear
two clicks), and tighten two top screws.
NOTE: Use only VESA-compatible alternative mounting method (100 mm pitch).
NOTE: Handle with care when removing monitor stand.
Figure S.2
Figure S.3
NOTE: When the LCD is in Landscape mode, be sure the two round indents
are at the bottom of the screen (Figure S.4).
Caution: Use the original screws (4 pcs) when mounting to avoid damage to the monitor
and stand. To fulfil the safety requirements the monitor must be mounted to an arm which
guarantees the necessary stability under consideration of the weight of the monitor.
The LCD monitor should only be used with an approved arm (e.g. GS mark).
Figure S.4
LaCie 319 LCD Monitor
User’s Manual
3.1 Controls
page 16
3.1. Controls
IMPORTANT: If you perform color-critical work, please bear in mind that manually altering the settings of your display could
significantly disturb the accuracy of the colors you display and undermine the benefits of your color-managed environment.
LaCie recommends that you not manually modify any Brightness/Contrast controls or the behavior of the Color Control
System.
OSM (On-Screen Manager) control buttons on the front of the monitor function as follows:
To access OSM menu, press any of the control buttons (EXIT, <, >, –, +).
To change signal input, press the SELECT button.
NOTE: OSM must be closed in order to change signal input.
Menu
EXIT
Exits the OEM controls.
Exits to the OSM main menu.
CONTROL </> Moves the highlighted area left/right to select control menus.
Moves the highlighted area up/down to select one of the controls.
ADJUST –/+
SELECT
Moves the bar left/right or changes the adjustment value to increase or decrease the adjustment.
Activates the selected function. Enter the OSM controls. Enter the OSM sub-menu. Select input while OSM
disappeared.
RESET
Resets the highlighted control menu to the factory setting.
NOTE: When RESET is pressed in the main and sub-menu, a warning window will appear allowing you to cancel the
RESET function by pressing the EXIT button.
Brightness/Contrast Controls
These options provide manual access to certain settings that influence the behavior of your display. If you are performing
color-critical work, LaCie recommends that you not manually modify the settings of these functions, as your LaCie blue eye pro
calibration software sets them automatically in accordance to your desired color settings. Modifying any of these settings man-
ually will significantly disturb the accuracy of the colors you display and undermine the benefits of your color-managed
environment.
BRIGHTNESS Adjusts the overall image and background screen brightness. Please do not modify manually if you are
performing color-critical work.
CONTRAST Adjusts the image brightness in relation to the background. Please do not modify manually if you are
performing color-critical work.
BLACK LEVEL (Analog input only) Adjust the black level. Please do not modify manually if you are
performing color-critical work.
AUTO CONTRAST (Analog input only) Adjusts the image displayed for non-standard video inputs. Please keep this
function OFF at all times if you are performing color-critical work.
LaCie 319 LCD Monitor
User’s Manual
3.1 Controls
page 17
AUTO BRIGHTNESS
Please keep this function OFF at all times if you are performing color-critical work.
1: Adjusts the brightness automatically, by detecting the brightness level of your environment and adjusting
the monitor with the best BRIGHTNESS setting*1.
2: Adjusts the brightness automatically for the best BRIGHTNESS setting based on the white display area.
The environmental brightness sensor has no function.
OFF: No function. LaCie recommends this position for calibrated monitor use.
NOTE: Do not cover environmental brightness sensor.
AUTO
Auto Adjust (Analog input only)
Automatically adjusts the Image Position and H. Size (or V. Size) settings and Fine settings.
Image Controls
LEFT / RIGHT Controls Horizontal Image Position within the display area of the LCD.
DOWN / UP Controls Vertical Image Position within the display area of the LCD.
H. SIZE (OSM ROTATION: Landscape) or V. SIZE (OSM ROTATION: Portrait) (Analog input only)
Adjusts the horizontal (or vertical) size by increasing or decreasing this setting. If the “Auto Adjust function” does not give you
a satisfactory picture setting, a further tuning can be performed manually using the “H. Size (or V. Size)” function (dot clock).
A Moiré test pattern could be used. This function may alter the width of the picture. Use Left/Right Menu to center the image
on the screen. If the H. Size (or V. Size) is wrongly calibrated, the
result would look like the drawing on the left.
When H. SIZE value is
wrong.
When H. SIZE value is
improved.
When H. SIZE value is
correct.
FINE (Analog input only)
Improves focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust function” and the
“H.Size” function do not give you a satisfactory picture setting, a fine tuning can be performed using the “Fine” function. It
improves focus, clarity and image stability by increasing or decreasing this setting.
A Moiré test pattern could be used. If the Fine value is wrongly calibrated, the result
would look like the drawing on the left.
When FINE value is
wrong.
When FINE value is
correct.
LaCie 319 LCD Monitor
User’s Manual
3.1 Controls
page 18
Color Control Systems
These options provide manual access to certain settings that influence the colorimetric behavior of your display. If you are per-
forming color-critical work, LaCie recommends that you not manually modify the settings of these functions, as your LaCie
blue eye pro calibration software takes care of this precisely and automatically in accordance to your desired color settings.
Modifying any of these settings manually would significantly disturb the accuracy of the colors you display and undermine the
benefits of your color-managed environment.
Color Control Systems: Seven color presets select the desired color setting (sRGB, NATIVE and PROGRAMMABLE
color presets are standard and cannot be changed). Color temperature increases or decreases, in each preset. Please do not
modify manually if you are performing color-critical work.
R,Y,G,C,B,M,S: Increases or decreases Red, Yellow, Green, Cyan, Blue, Magenta and Saturation depending upon
which is selected. The change in color will appear on screen and the direction (increase or decrease) will be shown
by the color bars. Please do not modify manually if you are performing color-critical work.
NATIVE: Original color presented by the LCD panel that is unadjustable.
PROGRAMMABLE: This mode is automatically activated by the LaCie blue eye pro calibration software to perform hardware
calibration of the display.
NOTE: To reset a poor image setting, turn on the monitor by using front power button while holding “EXIT” and “SELECT”
buttons at the same time.
Tools 1
SHARPNESS: This function is digitally capable to keep crisp image at any timings. It is continuously adjustable to get
distinct image or soft one as you prefer, and set independently by different timings.
EXPANSION MODE: Sets the zoom method.
FULL: The image is expanded to 1280 x 1024, regardless of the resolution.
ASPECT: The image is expanded without changing the aspect ratio.
OFF: The image is not expanded.
CUSTOM1: Zoom with center fixed. The image is expanded from the rate of 1.00 to 3.00 times individually for
horizontal (H. EXPANSION) and vertical (V. EXPANSION) direction by 0.01 step.
CUSTOM2: Zoom with top left corner fixed. The image is expanded from the rate of 1.00 to 3.00 times
individually for horizontal (H. EXPANSION) and vertical (V. EXPANSION) direction by 0.01 step.
LaCie 319 LCD Monitor
User’s Manual
3.1 Controls
page 19
VIDEO DETECT: Selects the method of video detection when more than one computer is connected.
FIRST DETECT: The video input has to be switched to “FIRST DETECT” mode. When current video input signal is not
present, the monitor searches for a video signal from the other video input port. If the video signal is present in
the other port, the monitor switches the video source input port to the new found video source automatically. The
monitor will not look for other video signals while the current video source is present.
LAST DETECT: The video input has to be switched to the “LAST DETECT” mode. When the monitor is displaying a sig-
nal from the current source and a secondary source is supplied, the monitor will automatically switch to the new
source. When current video signal is not present, the monitor searches for a signal from the other video input port. If
the video signal is present in the other port, the monitor switches the video port to the new source automatically.
NONE: The monitor will not search the other video input port unless the monitor is turned on.
DVI SELECTION: This function selects the DVI input mode (Input 1). When the DVI selection has been changed, the
computer has to be restarted.
AUTO: By using the DVI-D to DVI-D cable, the DVI SELECTION is DIGITAL. By using the D-SUB to DVI-A cable, the
DVI SELECTION is ANALOG.
DIGITAL: DVI digital input is available.
ANALOG: DVI analog input is available.
Note: For the MAC with digital output: Before turning on the MAC, the DVI Input mode must be set to DIGITAL in
“DVI SELECTION” of OSM by pressing “SELECT” button then “CONTROL” button when the DVI signal cable is con-
nected to the DVI-I connector (Input1) of the monitor. Otherwise the MAC may not turn on.
Note: Depending on the PC and Video card used, or when signal cable is attached, this function may not operate.
OFF TIMER: Monitor will automatically power-down when the end user has selected a pre-determined amount of time.
IPM: Monitor will go into power-save mode automatically a few minutes after the surrounding illumination is less than
the one pre-determined at the User Setting. You can adjust this illumination setting in the Advanced menu Tag 7.
During the power-save mode, the LED is amber blinking.
During the power-save mode, push any of the front buttons, except power button or SELECT button, and the monitor
will return to normal mode.
When the surrounding illumination is over than the one pre-determined at the User Setting, the monitor will return to
normal mode automatically.
Tools 2
LANGUAGE: OSM control menus are available in seven languages.
OSM LEFT/RIGHT: You can choose where you would like the OSM control image to appear on your screen.
Selecting OSM Location allows you to manually adjust the position of the OSM control menu left or right.
OSM DOWN/UP: You can choose where you would like the OSM control image to appear on your screen.
Selecting OSM Location allows you to manually adjust the position of the OSM control menu down or up.
OSM TURN OFF: The OSM control menu will stay on as long as it is use. In the OSM Turn Off submenu, you can
select how long the monitor waits after the last touch of a button to shut off the OSM control menu. The preset
choices are 10-120 seconds by 5 seconds step.
LaCie 319 LCD Monitor
User’s Manual
3.1 Controls
page 20
OSM LOCK OUT: This control completely locks out access to all OSM control functions. When attempting to activate
OSM controls while in the Lock Out mode, a screen will appear indicating the OSM controls are locked out.
There are three types of OSM LOCK OUT:
OSM LOCK OUT with BRIGHTNESS and CONTRAST control: To activate the OSM Lock Out function, press SELECT, then “+”
key and hold down simultaneously. To deactivate the OSM Lock Out, press SELECT, then “+” key and hold down
simultaneously while in the OSM menu. BRIGHTNESS and CONTRAST can be adjusted while in the lock out mode.
OSM LOCK OUT with no control: To activate the OSM Lock Out function, press SELECT, then “>” key and hold down
simultaneously. To deactivate the OSM Lock Out, press SELECT, then “>” key and hold down simultaneously while in the OSM
menu. No controls can be adjusted while in the lock out mode.
OSM LOCK OUT with BRIGHTNESS (only) control: To activate the OSM Lock Out function, press SELECT, then “–” and “<”
keys and hold down simultaneously. To deactivate the OSM Lock Out, press SELECT, then “+” key and hold down
simultaneously while in the OSM menu. BRIGHTNESS can be adjusted while in the lock out mode.
OSM ROTATION: To rotate OSM between Landscape and Portrait modes.
RESOLUTION NOTIFIER: This optimal resolution is 1280 x 1024. If ON is selected, a message will appear on the
screen after 30 seconds, notifying you that the resolution is not at 1280 x 1024.
HOT KEY: You can adjust the brightness and contrast directly. When this function is set to ON, you can adjust the
brightness with < or >, contrast with + or - key, while the OSM menu is off. The standard OSM can be accessed with
the EXIT button.
FACTORY PRESET: Selecting Factory Preset allows you to reset all OSM control settings (BRIGHTNESS, CONTRAST,
BLACK LEVEL, AUTO BRIGHTNESS, IMAGE CONTROL, COLOR CONTROL SYSTEM, SHARPNESS, EXPANSION MODE,
OFF TIMER, OSM POSITION, OSM TURN OFF, DISPLAY MODE) back to the factory settings. Individual settings can be reset
by highlighting the control to be reset and pressing the RESET button.
Information
DISPLAY MODE: Provides information about the current resolution display and technical data including the preset
timing being used and the horizontal and vertical frequencies. Increases or decreases the current resolution.
MONITOR INFO: Indicates the model and serial numbers of your monitor.
OSM Warning
OSM Warning menus disappear with Exit button.
NO SIGNAL: This function gives a warning when there is no Horizontal or Vertical Sync. After power is turned on or when
there is a change of input signal, the No Signal window will appear.
RESOLUTION NOTIFIER: This function gives a warning of use with optimized resolution. After power isturned on or when
there is a change of input signal or the video signal doesn’t have proper resolution, the Resolution Notifier window will open.
This function can be disabled in the TOOL menu.
OUT OF RANGE: When input signal is non-supported timing or the video signal doesn’t have proper
timing, the Out of Range menu will appear.
NOTE: If “ CHANGE DVI SELECTION” is displayed, switch to DVI SELECTION.
LaCie 319 LCD Monitor
User’s Manual
4. Troubleshooting
page 21
4. Troubleshooting
The Problem
No picture
Possible Solutions
• The signal cable should be completely connected to the display card/computer.
• The display card should be completely seated in its slot.
• Check the Vacation Switch should be in the ON position.
• Front Power Switch and computer power switch should be in the ON position.
• Check to make sure that a supported mode has been selected on the display card or system
being used.
(Please consult display card or system manual to change graphics mode.)
• Check the monitor and your display card with respect to compatibility and recommended set-
tings.
• Check the signal cable connector for bent or pushed-in pins.
• Check the signal input, “INPUT 1” or “INPUT 2”.
• Ensure the DVI input mode is set to DIGITAL when the MAC digital output is connected to the
DVI-I (Input1) connector.
Power Button does not
respond
• Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.
• Check the Vacation Switch on the left side of the monitor.
Image persistence
• Please be aware that LCD Technology may experience a phenomenon known as Image
Persistence. Image persistence occurs when a residual or “ghost” image of a previous image
remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not perma-
nent, but constant images being displayed for a long period of time should be avoided. To alleviate
image persistence, turn off the monitor for as long as the previous image was displayed. For
example, if an image was on the monitor for one hour and a residual image remains, the monitor
should be turned off for one hour to erase the image. NOTE: As with all personal display devices,
LaCIe recommends displaying moving imagesand using a moving screen saver at regular intervals
whenever the screen is idle or turning off the monitor when not in use.
Message “OUT OF
RANGE” is displayed
(screen is either blank or
shows rough images
only)
• Image is displayed only roughly (pixels are missing) and OSM warning “OUT OF RANGE” is
displayed: Either signal clock or resolution is too high. Choose one of the supported modes.
• OSM warning “OUT OF RANGE” is displayed on a blank screen: Signal frequency is out of
range. Choose one of the supported modes.
LaCie 319 LCD Monitor
User’s Manual
4. Troubleshooting
page 22
The Problem
Image is unstable or
unfocused
Possible Solutions
• Signal cable should be completely attached to the computer.
• Use the OSM Image Adjust controls to focus and adjust display by increasing or decreasing
the fine total. When the
display mode is changed, the OSM Image Adjust settings may need to be readjusted.
• Check the monitor and your display card with respect to compatibility and recommended sig-
nal timings.
• If your text is garbled, change the video mode to non-interlace and use 60Hz refresh rate.
• Please be aware that LCD Technology may experience a phenomenon known as Image
Persistence. Image persistence occurs when a residual or “ghost” image of a previous image
remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not per-
manent, but constant images being displayed for a long period of time should be avoided. To
alleviate image persistence, turn off the monitor for as long as the previous image was
displayed. For example, if an image was on the monitor for one hour and a residual image
remains, the monitor should be turned off for one hour to erase the image. NOTE: As with all
personal display devices, LaCIe recommends displaying moving imagesand using a moving
screen saver at regular intervals whenever the screen is idle or turning off the monitor when not
in use.
LED on monitor is not lit
(no green or amber color
can be seen)
• Power Switch should be in the ON position and power cord should be connected.
Display image is not
sized properly
• Use the OSM Image Adjust controls to increase or decrease the Coarse total.
• Check to make sure that a supported mode has been selected on the display card or system
being used.
(Please consult display card or system manual to change graphics mode.)
No Video
No Tilt
• If no video is present on the screen, turn the Power button off and on again.
• Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).
• Rotate the screen to 90° clockwise until you hear one click.
• Refer to the Quick Start section, “Remove monitor stand for mounting” to insure correct
installation of stand.
LaCie 319 LCD Monitor
User’s Manual
5. Contacting Customer Support
page 23
LaCie Technical Support
LaCie Belgium
LaCie Australia
Contact Us At:
Contact Us At:
LaCie Denmark
LaCie Canada
Contact Us At:
Contact Us At:
LaCie France
LaCie Finland
Contact Us At:
Contact Us At:
LaCie Italy
LaCie Germany
Contact Us At:
Contact Us At:
LaCie Netherlands
LaCie Japan
Contact Us At:
Contact Us At:
LaCie Spain
LaCie Norway
Contact Us At:
Contact Us At:
LaCie Switzerland
LaCie Sweden
Contact Us At:
Contact Us At:
LaCie USA
Contact Us At:
LaCie United Kingdom & Ireland
Contact Us At:
LaCie Grand Export
Contact Us At:
LaCie 319 LCD Monitor
User’s Manual
6. Warranty
page 24
6. Warranty
LaCie warrants your LaCie 319 LCD Monitor against any defect in material and workmanship, under normal use. In the event
this product is found to be defective within the warranty period, LaCie will, at its option, repair or replace the defective LaCie
319 LCD Monitor.
This warranty is void if:
• The LaCie 319 LCD Monitor was operated/stored in abnormal use or maintenance conditions;
• The LaCie 319 LCD Monitor is repaired, modified or altered, unless such repair, modification or alteration is expressly
authorized in writing by LaCie;
• The LaCie 319 LCD Monitor was subjected to abuse, neglect, lightning strike, electrical fault, improper packaging or
accident;
• The LaCie 319 LCD Monitor was installed improperly;
• The serial number of the LaCie 319 LCD Monitor is defaced or missing;
• The broken part is a replacement part such as a pickup tray, etc.
• The tamper seal on the LaCie 319 LCD Monitor is broken.
LaCie will not, under any circumstances, be liable for direct, special or consequential damages such as, but not limited to,
damage or loss of property or equipment, loss of profits or revenues, cost of replacement goods, or expense or inconvenience
caused by service interruptions.
Under no circumstances will any person be entitled to any sum greater than the purchase price paid for the monitor.
To obtain warranty service, call LaCie Technical Support. You will be asked to provide your LaCie product’s serial number, and
you may be asked to furnish proof of purchase to confirm that the monitor is still under warranty.
All monitor returned to LaCie must be securely packaged in their original box and shipped with postage prepaid.
i
|