Kicker SX SERIES SX6501 User Manual

VFD DISPLAY - cont

KEYPAD

ISIS

VFD Display

GAIN - Indicates you are in the gain menu.

EQ - Indicates you are in the equalizer menu.

LPF - Indicates you are in the low pass filter menu.

HPF - Indicates you are in the high pass filter menu.

PHASE - Indicates you are in the phase menu.

KOMP - Indicates you are in the Kompressor menu.

MEM-1 - Memory preset 1 activated.

The keypad consists of nine buttons that allow you to adjust

your amplifier.

Meet the ISISinterface (Indicate Status & Input Settings).

The ISIS(pronounced eye-sis) allows you to view the cur-

rent conditions and settings of your amplifier as well as

change the many user-adjustable settings.The ISISsystem

consists of the VFD (Vacuum Fluorescent Display) and the nine

soft touch buttons that make up the KEYPAD.

AMP1

AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

M1 - Used to select memory preset 1 or to store cur-

rent settings into preset 1.

* kicker *

MEM-1

MEM-2

MEM-3

MEM-4

M2 - Used to select memory preset 2 or to store

current settings into preset 2.

Here is a brief description of the indicators found on the

VFD.

AMP1 - Indicates amplifier 1 is selected for adjustment. Only

M3 - Used to select memory preset 3 or to store

current settings into preset 3.

ISIS

VFD

AMP1

AMP2

available in four channel amps.

M4 - Used to select memory preset 4 or to store

current settings into preset 4.

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

MEM-2 - Memory preset 1 activated.

AMP2 - Indicates amplifier 2 is selected for adjustment.

Only available in four channel amps.

* kicker *

MEM-1

MEM-2

MEM-3

MEM-4

ESC

ESC - Used to exit the current menu.

MEM-3 - Memory preset 1 activated.

LOCK - Indicates the amplifier controls are locked out and

not usable.

ENT - Used to enter the selected menu.

ENT

MEM-4 - Memory preset 1 activated.

HOME - Used to return to the Main menu and

other functions explained later.

HOME

ISIS

KEYPAD

LEFT - Indicates an action or adjustment of the left channel.

M1 M2 M3 M4

SYS - Indicates you are in the system menu.

UP - Used to advance up through menu selections

and/or adjust amplifier controls.

RIGHT - Indicates an action or adjustment of the right

ESC

ENT

HOME

channel.

DOWN - Used to advance down through menu

selections and/or adjust amplifier controls.

MUTE - Indicates you are in the mute menu or the mute

function is active.

These controls and their usage will be explained later with

more detail in each menu usage section.

SX .1 Series Amplifiers

Remove

Custom-machined power block accepts up to a 2 Ga wire

for both power and ground connections and up to an 8 Ga for

remote turn-on assures maximum power transfer with

minimal loss.

End Panel Views

Mounting

The BLAST Port is used to connect the Remote Bass Level

Controller and for transferring control signals from one SX

amplifier to another SX amplifier. An RJ45 cable is required to

connect the BLAST Port (Out) of one amp to the BLAST Port

(In) of another. This is only required if you want to control

more than one amplifier with the same Bass Level Controller.

More details on this further in the manual.

When selecting a location to mount your Kicker amplifier be

sure it is structurally sound and that there are no items

behind the area that could be damaged by the screws. Check

for wiring, brake lines, fuel lines, gas tanks, etc.

On-board fusing (number of fuses vary by amp size) to

protect amplifier against over current conditions and reverse

polarity.

AMP1

AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

* kicker *

MEM-4

MEM-1

MEM-2

MEM-3

All amplifiers generate heat under normal operation. Be sure

to choose a location that allows adequate ventilation for the

amplifier. Also consider that the air temperature inside an

automobile’s trunk can reach upwards of 140 degrees fahren-

heit. An amplifier mounted in the trunk may require additional

cooling such as extra fans moving air around the amplifier’s

chassis or ventilating the trunk to exchange the hot air in the

trunk for cooler air outside. If possible, mounting the amp in

the passenger compartment will allow cooler operation.

M1 M2 M3 M4

Power LED indicates amplifier is powered up and operating.

ESC

HOME

ENT

The speaker terminals are custom-machined connectors

with full protective shrouds and are designed to accept heavy

gauge speaker wire assures maximum power transfer and

damping with minimal power loss.

Check Fuse LED indicates a fault with the end panel fuses.

This could be fuses which are not seated properly, faulty fuses

or blown fuses.

Fig. 1

Remove

NOTE...

Gold-plated RCA input connectors and PAST jacks provide

solid input and output connections for your pre-amp signal.

With the EndKaps removed, you now have access to the

four mounting holes in the mounting feet and all wiring

connections. Drill 4 holes using a 7/64” drill bit and use the

supplied #8 screws to mount the amplifier.

See Fig. 2

SX1250.1 does not have on-board fusing or the Check Fuse

LED due to larger external fusing requirements.

BLAST Port In

BLAST Port Out

Remember that the controls on top of the amp will need to

be accessible for adjustment later. Keep this in mind as you

choose your amplifier’s mounting location.

Power LED

Check Fuse LED

Fusing

Now that you are ready to mount your amplifier, use the

supplied 3mm allen wrench to remove the amplifier EndKaps.

This will give you access to the mounting holes in the amplifi-

er and all wiring connections.

Speaker +

Speaker -

Left PAST

Right PAST

Right Input

Left Input

AMP1

AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

See Fig. 1

* kicker *

MEM-4

MEM-1

MEM-2

MEM-3

Ground

Remote

+ 12 Volt

M1 M2 M3 M4

ESC

HOME

ENT

Fig. 2

SX .1 Series Amplifiers

The ground should be connected to the amplifier first

before making any of the other connections. This wire should

be as short as possible (24 inches or less) and connected to a

paint/corrosion free solid metal area of the car’s chassis. Use

the same gauge wire as recommended for the amplifier’s

power connection to the battery. Adding an additional ground

wire between the car battery’s negative post and the car chas-

sis of this same gauge (or larger) is also recommended.

System Diagrams

Wiring

SINGLE SPEAKER OR VOICE COIL

Signal is input into the amplifier using the low level RCA

input connections. If your source unit does not have RCA

output connectors you will need to use a Hi-Lo level signal

adapter. See your Kicker dealer for more details on this.

SX.1 series amplifiers are capable of operating into a minimum impedance of 2 ohms

(SX650.1) or 1 ohm (SX1250.1).

GROUND

SIGNAL IN

The output (PAST) RCA jacks provide an unaltered signal

output to feed another amplifier or component.

SIGNAL OUT

If you ever need to remove the amp from the vehicle after

it has been installed, the ground wire should be the last wire

disconnected from the amplifier, just the opposite of when

you installed it.

REMOTE

TURN-ON

18"

SOURCE UNIT

AMP

LOCK LEFT SYS RIGHT MUTE

GAINEQ LPF HPF PHASE KOMP

or less

8.8.8.8.8.8.8.8.8.8

A fuse must be installed within 18 inches of the battery to

protect the power wire feeding your amplifier. This fuse

should be of at least the same value used in the amplifier but

no higher than the capacity of the power wire. See the charts

below for wire size and fusing recommendations.

S-

+12V

FUSE

ESC

HOME

ENT

S+

BATTERY

MULTIPLE SPEAKERS OR VOICE COILS PARALLEL WIRED

Model

Fuse Size

Wire Size

SX650.1

SX1250.1

60A

150A

4 GA

2 GA

SX.1 series amplifiers are capable of powering multiple speakers or voice coils wired in

parallel as long as the minimum impedance does not drop below 2 ohms (SX650.1) or 1

ohm (SX1250.1).

GROUND

SIGNAL IN

The use of twisted pair interconnects is recommended for

all installations to minimize noise. When routing these cables

through the automobile, try to keep them away from factory

wiring harnesses and other power wiring. If you need to cross

any of this wiring do so at a 90 degree angle to reduce the

possibility for noise problems.

Wire Size

Length

Maximum Fuse

SIGNAL OUT

8 Ga

70 Amps

175 Amps

250 Amps

400 Amps

40 Amps

90 Amps

150 Amps

200 Amps

Less than

10 feet in

length

REMOTE

TURN-ON

4Ga

2 Ga

0Ga

18"

AMP

LOCK LEFT SYS RIGHT MUTE

GAINEQ LPF HPF PHASE KOMP

or less

8.8.8.8.8.8.8.8.8.8

8 Ga

4 Ga

2 Ga

0 Ga

S-

10 feet to

20 feet in

length

+12V

FUSE

ESC

HOME

ENT

S+

When working with power connections it is always recom-

mended that you disconnect the battery to prevent accidents.

BATTERY

SX .1 Series Amplifiers

MULTIPLE SPEAKERS OR VOICE COILS SERIES WIRED

AMPLIFIER STRAPPING

SX.1 series amplifiers are capable of powering multiple speakers or voice coils wired in

series as long as the minimum impedance does not drop below 2 ohms (SX650.1) or 1 ohm

(SX1250.1).

SX.1 series amplifiers are capable of being strapped

together to provide twice the power into twice their rated

minimum impedance. Only like model amps can be strapped

together. In other words, the SX650.1 can only be strapped to

another SX650.1 and the SX1250.1 can only be strapped to

another SX1250.1.

SOURCE UNIT

GROUND

SIGNAL IN

SIGNAL OUT

REMOTE

TURN-ON

AMP STRAPPING

NOTE...

4 ohm minimum impedance for SX650.1 when strapped.

18"

AMP

LOCK LEFT SYS RIGHT MUTE

GAINEQ LPF HPF PHASE KOMP

or less

8.8.8.8.8.8.8.8.8.8

2 ohm minimum impedance for SX1250.1 when strapped.

S-

+12V

FUSE

ESC

HOME

ENT

S+

BATTERY

1.) Wire both amplifiers to 12 volt power, ground and

remote.

AMP STRAPPING

2.) Connect a RCA cable from the source unit to the RCA

Input jacks on the primary amp.

These are just a few of the many ways you can use your SX.1 series Kicker amplifier.

These system diagrams are designed to give you a basic understanding of the most com-

mon uses for this amplifier. For more complex systems please visit your local authorized

Kicker dealer. You can also download the SX Technical Manual from our website at

www.kicke r .com for more detailed information and complex system diagrams.

3.) Use the supplied 1/8 inch mono cable to connect the

Amp Strapping Out jack of the primary amplifier to the

Amp Strapping In jack of the secondary amplifier.

4.) Use a short piece of heavy gauge wire (12Ga, 10Ga, 8Ga)

to connect the Speaker negative terminals of both amps

together.

5.) The primary amplifier’s positive terminal is used for the

positive speaker connections.

6.) The secondary amplifier’s positive terminal is used for the

negative speaker connections.

SX .1 Series Amplifiers

BACK VIEW

SIDE VIEW

Mounting Surface

AMPLIFIER STRAPPING WITH REMOTE BASS CONTROL

USING THE SIGNAL OUTPUT JACKS (PAST)

The Output (Pre Amp Signal Transfer) RCA jacks allow you to

send the incoming signal from one Kicker SX series amplifier

to another amplifier or processor without the need for Y

cables. The signal from the PAST jacks is identical to the signal

fed to the amplifier via its RCA input jacks and is not affected

by any of the amplifier’s built-in digital signal processing.

The Remote Bass Level Controller can be used to adjust the

output level of both the amplifiers that are strapped together.

SOURCE UNIT

1.) Mount the Remote Bass Level Controller in the front of

your vehicle and plug in the supplied cable.

SUPPLIED

CABLE

SOURCE UNIT

2.) Route the supplied cable to the primary amplifier and

connect to its BLAST In jack.

Most head units with high voltage outputs should be capa-

ble of driving up to ten amplifiers in a chain.

AMP STRAPPING

3.) Enjoy!

AMP STRAPPING

To Next Amplifier or Processor

SX .1 Series Amplifiers

USING THE REMOTE BASS LEVEL CONTROL & BLAST

As you can see there can be an infinite number of menu

levels and each one of these menu levels can have an infinite

number of its own items.

BACK VIEW

SIDE VIEW

Mounting Surface

Navigation

You can use the Remote Bass Level Control to control the

output of your amplifier from the front of the car.

Your KICKER SX series amplifier uses the latest in Digital DSP

control and provides you with valuable operational informa-

tion about your amplifier, real-time diagnostics and a full

multi-level menu-driven operating system to access and

adjust your amplifier.

Navigating this simple menu

ESC

HOME

ENT

Mount the controller by simply screwing the metal bracket

to the chosen location and then slide the housing onto the

bracket until it snaps into place.

structure is very easy using the 5-way

keypad.

SUPPLIED

CABLE

You use the UP and DOWN keys to scroll through the

available menu items, and the ENT key is used to select that

menu item. The ESC key backs you up one menu level from

where you are, and the HOME key can return you all the

way to MAIN MENU by pressing and holding it for 1.5 seconds.

Route the cable from the controller to the BLAST input jack

on the amplifier chassis. That’s it.

The menu system is designed in layers. There is a starting

point and you keep drilling down until you get to the menu

item you want to view or change. This menu tree is an

example of how the SX menu structure is set up.

SOURCE UNIT

If you wish to control more than one amplifier with your

remote, you will simply need to use a RJ45 cable (not supplied

but available at any Radio Shack, computer store or electronics

center) to connect the BLAST output jack of the first amp to

the BLAST input jack of the next amplifier.

NOTE: Not all the menus and menu items are shown below.

DEFAULT

SCREEN

For example let’s begin at the DEFAULT SCREEN; our goal is

to get to the HISTORY menu. Pressing the ENT key would get

us to MAIN MENU. Now use the UP and

DOWN keys to scroll to SYSTEM, and

then press the ENT key. Now you are

AMP STRAPPING

MAIN MENU

SYSTEM

GAIN

in the SYSTEM MENU. Using the UP and

DOWN keys again you scroll to SICK

BAY and press the ENT key. You are

now in the SICK

SYSTEM MENU

ESC

HOME

ENT

OPTIONAL

RJ45 CABLE

VOLT NOW

LO-PASS

VOLT MIN

HI-PASS

VOLT MAX

TEMP NOW

TEMP MAX

RUN TIME

SICK BAY

AMP STRAPPING

BAY MENU. Use the UP and DOWN

keys again to scroll to HISTORY and then

press the ENT key. That’s it! You are

there.

∝

ESC

HOME

ENT

SICK BAY MENU

This is how you view information

and change settings in your KICKER SX amplifier.

OPTIONAL

RJ45 CABLE

∝

CURRENT

HISTORY

∝

To Next Amplifier

SX .1 Series Amplifiers

Continuing our example, we are now in the HISTORY item in

the SICK BAY MENU. If we press the

ESC key we would go back up to the

SICK BAY MENU. If we press the ESC

Pressing the key and holding it in for

longer than 1.5 seconds will activate the

accelerated scrolling mode and scroll

through the menu items at a much

faster rate. Releasing the key will return

it to normal speed mode.

If you want the display to continue scrolling simply press

the HOME key again.

PRESS &

HOLD

Menu System

The menu system layout is as follows:

MAIN - This menu is the first menu accessed from the

DEFAULT menu and is the gateway to all the settings and

information on your SX series amplifier.

ESC

HOME

ENT

DEFAULT - This menu is displayed when your amp is

operating and no adjustments are being made to your ampli-

fier. This information scrolls through the display one after the

other and then repeats.

key again we would go to the SYSTEM

ESC

HOME

ENT

MENU. One more press of the ESC

key and we are in the MAIN MENU.

Don’t try to scroll through every 1/12 octave step without

To enter the MAIN menu simply press

Let’s start at the HISTORY item in the SICK BAY MENU again

but instead press and hold the HOME key for 1.5

seconds. Doing this will take us all the way back to the MAIN

it!

the ENT key while in the DEFAULT

menu.

ESC

HOME

ENT

1.) KICKER- Hey, we needed a brand plug for us since this

amp is sooooo cool!

MENU in one key press. Pressing and

holding the HOME key will return you

all the way back to the MENU ITEM you

started with in the MAIN MENU, no mat-

ter how deep in the menu level struc-

ture you are. Pretty cool!

PRESS &

HOLD

2.) XX.X Volts- Displays the current voltage at the

amplifier’s + 12 volt battery input terminal.

The available selections in the MAIN menu are:

ESC

HOME

ENT

System

GAIN

3.) XX.X DEG f or xx.x DEG c- Displays the current

temperature of the amplifier in celsius or fahrenheit.

Lo-Pass

Hi-Pass

Phase

4.) amp name- Model name of the amplifier or the name

you have changed it to.

This is a very quick way to return to the MAIN MENU after

drilling down several menu layers to view or change an item.

Mute

Kompressor

Security

5.) memory name- Current memory preset in use (if

any) or the name you have changed it to.

When adjusting any amplifier control the UP and DOWN

arrow keys have 2 speeds, normal and accelerated.

PRESS &

If you want to freeze the scrolling

Use the UP and DOWN arrow keys

to scroll through the available selections

in the MAIN menu.

display simply press the HOME key

and the scrolling will stop.

ESC

HOME

ENT

Pressing and releasing the key

repeatedly will scroll through the menu

items at normal speed.

RELEASE

ESC

HOME

ENT

ESC

HOME

ENT

When you have the menu item

selected that you want to view or adjust

simply press the ENT key to select it.

Now you can manually select the item

you wish to have displayed by using the

UP or DOWN keys.

ESC

HOME

ENT

ESC

HOME

ENT

SX .1 Series Amplifiers

SICK BAY - cont

8.) Amp Name- Here you can assign a unique name to

your KICKER SX amplifier. This name will replace the model

name in the DEFAULT screen. If you change your mind and

do not want to change the name, press and hold the

HOME key for 1.5 seconds BEFORE making any changes.

SYSTEMMENU - This menu item contains many diagnostic

tools and first time setup options. Use the UP and DOWN

arrow keys to scroll through the options and press ENT to

select. Press the ESC key to return to the SYSTEM menu.

7a.) CURRENTshows amplifiers current status or fault

code. The 6 possible codes are:

7c.) PINK NOISEis a built in pink noise generator

to test operation of the amplifier

normal- No problem, normal operation.

thermal- Thermal cutoff protection engaged.

short- Short circuit protection engaged.

Hi-Volt- High voltage protection engaged.

FUSE- Faulty or blown power fuse.

Use the UP and DOWN

keys to select NOISE ONor

NOISE OFf.

1.) Volt Now- Displays the current voltage at the

amplifiers +12 volt terminal.

The ESC and ENT keys move

ESC

HOME

ENT

the cursor left or right to select

which character to change.

2.) Volt Min- Displays the lowest voltage seen at the

amplifiers +12 volt terminal since being installed.

SERVICE- Amp requires service by KICKER.

ESC

HOME

ENT

When the PINK NOISE is ON

the LEFTand RIGHTindicators

in the ISISVFD will blink on

and off.

When you are done viewing

the current status press the

ESC key to return to the SICK

AMP1

AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

3.) Volt Max- Displays the highest voltage at the

amplifiers +12 volt terminal since being installed.

ESC

HOME

ENT

noise on

MEM-4

MEM-1

MEM-2

MEM-3

BAY menu.

Use the UP and DOWN keys to

change the character displayed

(A, B, C...1, 2, 3...etc)

4.) Temp Now- Displays the current temperature of

the amplifier.

7b. )HISTORYlogs the last 5 fault codes and how

long ago they happened when

compared to the RUN TIME log.

ESC

HOME

ENT

When you are done using the

PINK NOISE generator press the

ESC key to return to the SICK

BAY menu.

5.) Temp Max- Displays the highest temperature the

amplifier has reached since being installed.

ESC

HOME

ENT

Use the UP and DOWN

PRESS &

HOLD

ESC

HOME

ENT

When you are finished press and

hold the HOME key for 1.5

seconds to save your new

amplifier name.

6.) Run Time- Displays the total time the amplifier

has been powered up since installation in 1/10th of

an hour increments

keys to select the HISTORY log

entry you want to view.

NOTE...

ESC

HOME

If you exit the SICK BAY menu with the PINK NOISE generator

still on, the LEFTand RIGHT ISISVFD indicators will remain

blinking as a reminder.

ENT

7.) Sick Bay- Contains several

Press and hold the ENT key

to view the time it happened.

ESC

HOME

ENT

diagnostic tools. Once in this menu

you use the UP and DOWN keys to

scroll through CURRENT, HISTORYand

PINK NOISEoptions. Press the ENT

When you are done viewing

ESC

HOME

ENT

key to select.

the history press the ESC key.

ESC

HOME

ENT

SX .1 Series Amplifiers

9.) Mem Name- Here you can change the names of the

memory locations. The factory defaults are

14.) Display- Several options to allow customizing

the amplifier’s VFD display.

15.) Lock Code- Set your own lock code! The factory

default is 123but you can change it and create your own

code with up to 10 characters.

10.) Remote Adr- This feature is currently not used but is

reserved for future expansion.

Memory-1

Memory-2

Memory-3

14a.) BRIGHTNESS- Adjust the intensity level of

the ISISVFD display. Five selectable levels.

11.) Gain Range- Sets the input voltage window of the

UltraMatch gain control. Possible choices are:

1V, 2V, 4V, 8V, 16V

Select the one closest to the maximum RCA input voltage

you expect to send to the amplifier.

The ESC and ENT keys move the

cursor left or right to select which

character to change.

MINIMUM- dimmest setting.

LOW

MEDIUM

HIGH

ESC

HOME

ENT

ESC

HOME

ENT

Memory-4

Use the UP and DOWN keys to select the memory

location name you want to change and then press the

MAXIMUM- brightest setting.

Use the UP and DOWN keys to

change the character displayed (

A, B, C...1, 2, 3...etc)

Use the UP and DOWN keys to

select your voltage. Press the ESC to

return to the MAIN menu.

ENT key to select it.If you change your mind and do not

want to change the name, press and hold the HOME key

for 1.5 seconds BEFORE making any changes.

14b.) TEMP C/F- Selects between Celsius (CELSIUS)

or Fahrenheit (FAHRENHEIT) for temperature

readouts.

ESC

HOME

ENT

ESC

HOME

ENT

12.) Bypass DSP- Bypasses all DSP

The ESC and ENT keys move the

cursor left or right to select which char-

acter to change.

processing and sends the input signal directly to the

amplifier.

PRESS &

HOLD

14c.) HOLD TIME- Adjusts the speed of the scroll

in the Default Screen display. Determines how long

each menu item stays in the display before scrolling

to the next item. Adjustable from 1 - 11 seconds.

When you are finished press and

hold the HOME key for 1.5 seconds

to save your new amplifier lock code.

IMPORTANT!!! Be sure to write this

code down for future reference.

ESC

HOME

ENT

Use the UP and DOWN keys to

select BYPASS ONor BYPASS OFF.

Press the ESC key to return to

ESC

HOME

ENT

ESC

HOME

ENT

Use the UP and DOWN keys to

change the character displayed

(A, B, C...1, 2, 3...etc)

14d.) SCRNSAVER- Option to turn on or off the

screensaver. When on (AUTO) the display will go to

sleep when there is no button activity for 60 seconds.

Pressing any button once will wake up the display.

The OFFselection turns off the screensaver and the

display is always on.

the MAIN menu.

13.) Komp Adj.- This adjusts the KOMPRESSOR

ESC

HOME

ENT

activation threshold. Range is +24 dB to -24 dB to allow for

different sized speakers or listener tastes. 0 is the

default factory setting.

PRESS &

HOLD

When you are finished press and hold

the HOME key for 1.5 seconds to save

your new memory name.

Use the UP and DOWN keys to

select your setting and then press the

ESC to return to the MAIN menu.

ESC

HOME

ENT

ESC

HOME

ENT

Repeat the above steps to rename the other presets.

SX .1 Series Amplifiers

EQMENU - Here you can adjust the single band parametric

equalizer. Your options are frequency, bandwidth and

boost/cut.

BOOST/CUTis how much you want to boost or cut the

equalizer and has a range of -18 dBto + 18 dBin .5 dB

steps.

16.) Reset Amp- This option resets all adjustable

settings back to their original factory defaults.

GainMENU - Here is where you adjust your amplifier’s gain

control settings.

Use the UP and DOWN keys to

select SKIP RESETor DO RESET and

then press the ENT key to perform

Press the ENT key to enter the GAIN

adjustment menu.

Press the ENT key to enter the EQ

adjustment menu.

Use the UP and DOWN keys to

boost or cut the EQ and then press

the ESC key to return to the EQ

menu.

ESC

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

the selected action.

Use the UP and DOWN keys to

scroll through frequency, bandwidth

and boost/cutand press the ENT

key to select.

Now use the UP and DOWN keys

to increase or decrease the gain of

the amplifier in .5 dB increments from

0 dB to +12 dB. (.0to 12.0)

When you are done adjusting the

EQ press the ESC key while in the

EQ frequency, bandwidth and

boost/cutoption menu to return to

the MAIN menu.

17.) About- This menu item will display information

about the DAP (Digital Audio Processor) hardware, software

and build date.

ESC

HOME

ENT

ESC

HOME

ENT

ESC

HOME

ENT

Use the UP and DOWN keys to

view the DSP Version, Software Version,

Hardware Version and Build Date. Press

the ESC key to return to the MAIN

FREQUENCYselects the center frequency of the EQ and can

be set at any 1 Hz spaced frequency from 20 Hz- 200 Hz.

Press the ESC key to return to the

MAIN menu when finished adjusting

the gain control.

NOTE...

While adjusting the EQ you will notice the EQ indicator on

the ISIS VFD display is lit. This indicates you are in the EQ

menu.

ESC

HOME

ESC

HOME

ENT

Use the UP and DOWN keys to

select your frequency. Press the

ESC to return to the EQ menu.

menu.

NOTE...

ESC

HOME

ENT

While adjusting the GAIN you will notice the gain indicator

on the ISIS VFD display is lit. This indicates you are in the

GAIN menu.

BANDWIDTH(better known as Q) can be set from .5to 10in

.5 increments. In simple terms, lower Q effects more

frequencies around the center frequency while higher Q

effects fewer frequencies around the center frequency.

Use the UP and DOWN keys to

select your Q value. Press the ESC

to return to the EQ menu.

ESC

HOME

ENT

SX .1 Series Amplifiers

The KICKER SX amplifier monitors and prevents any high

pass crossover point from being any closer than 1/3 octave

from the low pass crossover point. If you cannot set the high

pass crossover where you want then check the LPFindicator

and see if it is flashing. If it is then you need to go to the

LO-PASS menu and lower the low pass crossover point.

The KICKER SX amplifier monitors and prevents any low pass

crossover point from being any closer than 1/3 octave from

the high pass crossover point. If you cannot set the low pass

crossover where you want then check the HPFindicator and

see if it is flashing. If it is then you need to go to the HI-PASS

menu and raise the high pass crossover point.

hi-passMENU - Here is where you adjust the high pass

crossover. Your options are frequency and SLOPE.

Lo-PassMENU - Here is where you adjust the low pass

crossover. Your options are frequency and SLOPE.

Press the ENT key to enter the

LO-PASS adjustment menu.

ESC

HOME

ENT

ESC

HOME

ENT

This is done as a safety precaution to prevent a notch

filter condition.

This is done as a safety precaution to prevent a notch filter

condition.

Use the UP and DOWN keys to

scroll through frequencyand SLOPE

and press the ENT key to select.

Use the UP and DOWN keys to

scroll through frequencyand SLOPE

and press the ENT key to select.

ESC

HOME

ENT

ESC

HOME

ENT

FREQUENCYselects the crossover point and can be set at any

1 Hz spaced frequency from 10 Hzto 60 Hz.

FREQUENCYselects the crossover point and can be set at any

1 Hz spaced frequency from 30 Hzto 200 Hz.

Use the UP and DOWN keys to

select your frequency. Press theESC

key to return to the HI-PASS menu.

Use the UP and DOWN keys to

select your frequency. Press the

ESC to return to the LO-PASS

ESC

HOME

ENT

ESC

HOME

ENT

menu.

SLOPEselects the rolloff of the crossover and can be set

from OFFto 24 dBin 6 dB steps.

SLOPEselects the rolloff of the crossover and can be set

from oFFto 48dBin 6 dB steps.

Use the UP and DOWN keys to

select your slope. Press the ESC

to return to the HI-PASS menu.

Use the UP and DOWN keys to

select your slope. Press the ESC to

return to the LO-PASS menu.

ESC

HOME

ENT

ESC

HOME

ENT

NOTE...

While adjusting the high pass crossover you will

notice the hpfindicator on the ISIS VFD display is

lit. This indicates you are in the HI-PASS crossover menu.

While adjusting the low pass crossover you will notice the

LPFindicator on the ISIS VFD display is lit. This indicates

you are in the LO-PASS crossover menu.

SX .1 Series Amplifiers

PhaseMENU - Here you can switch the polarity of the ampli-

fier’s output between 0 or 180 degrees. Your options are

0 degree and 180 degree.

7.) Mute- Here you can mute the amplifier’s output for

setup or testing purposes. Your options are MUTE ON and

MUTE OFF.

KompressorMENU - Here you can select which Kompressor

setting you wish to use. The SX amplifier utilizes a full digital

compressor circuit to tweak the amplifier and the sound to

your unique needs. Your options are RED-LINE, CONTOUR,

ATTACK, and OFF.

Press the ENT key to enter the

ESC

HOME

ENT

ESC

HOME

ENT

PHASE adjustment menu.

MUTE adjustment menu.

Press the ENT key to enter the

ESC

HOME

ENT

KOMPRESSOR adjustment menu.

Use the UP and DOWN keys to

scroll through 0 degreeand

180 degreeand press the ENT key

to select.

Use the UP and DOWN keys to

scroll through MUTE ON and

MUTE OFF.

ESC

HOME

ENT

ESC

HOME

ENT

Once in this menu use the UP and

DOWN keys to scroll through

RED-LINE, contour, attackand OFF.

ESC

HOME

ENT

Press the ESC key to make

your selection and return to the

MAIN menu.

Press the ESC key to make

your selection and return to the

MAIN menu.

ESC

HOME

ENT

ESC

HOME

ENT

Press the ESC key to accept your

selection and return to the MAIN

menu.

ESC

HOME

ENT

NOTE...

While adjusting the PHASE you will notice the PHASE

NOTE...

indicator on the ISIS VFD display is lit. This indicates you

are in the PHASE menu.

While adjusting the MUTE you will notice the muteindica-

tor on the ISIS VFD display is lit. This indicates you are in

the MUTE menu.

NOTE...

While adjusting the Kompressor you will notice the KOMP

indicator on the ISIS VFD display is lit. This indicates you

are in the KOMPRESSOR menu.

If you exit the MUTE menu with the muting activated, the

MUTEindicator will flash to indicate this.

See the specifications pages for a brief description of each

Kompressor setting and some general guidelines for their use.

SX .1 Series Amplifiers

UNLOCK AMPLIFIER - cont.

You will need to call KICKER directly at (405) 624-8583 to

handle this situation. You will need your amplifier’s serial

number AND your receipt as the guys and gals answering the

phone will need this information from you to help you out.

UNLOCK AMPLIFIER

SecurityMENU - Here you can lock down your amplifier to

prevent any access to the settings. The DEFAULT screen is still

active and you can select any of the four presets... but that is

it!

If you enter the wrong code the display will flash the mes-

sage BAD CODEand then return you to UNLOCKscreen.

You do remember your lock code right? You better because

that is now the only way in! If you have not changed it then it

is still at the factory default of 123.

AMP1

AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

So...before you call, gather this information up and have it

ready to save us some time on the phone. Cool? Cool!

Press the ENT key to enter the

2 Times

ESC

HOME

ENT

To unlock your amplifier press the

ENT key. The display will show

UNLOCK. Press the ENT key again.

You will now enter your code to

unlock the amplifier.

bad code

SECURITY menu.

MEM-1

MEM-2

MEM-3

MEM-4

AMP1

AMP2

Better yet, take the time RIGHT NOW to fill out the first page

in this manual and STAPLE your receipt to it. That way if or

when you need service (like forgetting your lock code) you will

have all the information you need right there in front of you.

ESC

HOME

ENT

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

Use the UP and DOWN keys to

select LOCK IT UPor DON’T LOCK

and then press the ENT key to

accept your setting.

unlock

MEM-4

MEM-1

MEM-2

MEM-3

ESC

HOME

ENT

Press the ENT key to enter your

lock your code again.

The ESC and ENT keys move the

blinking cursor left or right to select

which character to enter.

ESC

HOME

ENT

ESC

HOME

ENT

If you selected LOCK IT UPthe display will now show

UNLOCK and the LOCK indicator will be on . The menus

are now locked.Press the ESC key to return to the

DEFAULT scrolling screen.

Enter your code again making sure to place the correct

character in the correct position in the display. Blank spaces

count as part of the code so be sure you are entering it

correctly.

Use the UP and DOWN keys to

enter the character.

(A, B, C...1, 2, 3...etc)

AMP1

AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

ESC

HOME

ENT

unlock

MEM-4

MEM-1

MEM-2

MEM-3

Press and hold the HOME key and try again. If you have

found your error then the amp will unlock. If not, the flashing

BAD CODEwill greet you and you can try again.

If you selected DON’T LOCKthen you will return to the

MAIN menu and the amplifier will remain unlocked.

When you are finished press and hold

the HOME key for 1.5 seconds to

enter your unlock code.

ESC

HOME

ENT

If you have tried several times (several is defined as more

than 3...less than 10) and you still can not unlock your

amplifier, this more than likely means means you have

forgotten your lock code.

NOTE...

While your amplifier is in lock down you will notice the LOCK

indicator on the ISIS VFD display is lit. This indicates your

amplifier is locked down and will require a code to unlock it

before any adjustments can be made.

If the code is correct the amp will unlock and drop you back

into the MAIN menu. If not, then read on...

SX .1 Series Amplifiers

In more general terms, each preset offers you these

options.

STORING A PRESET

PRESET PRESETS

Memory Presets

There are four memory preset keys each with an

indicator above it in the ISISVFD display. The indicator will

illuminate if that

Make all the adjustments you want to have stored in the

preset and return to the DEFAULT screen.

Ok, we know that sounds like a certain pizza commercial,

but seriously the four memory presets come with settings

already in them.

Memory-1 sets the amplifier up with a 24 dB per octave

low-pass crossover at 80 Hz and an infrasonic filter (often

called subsonic filter) to protect the speakers from harmful

ultra-low frequencies.

memory preset is

To store your settings into a preset

HOLD

currently in use.

simply press and hold the desired

memory key until the VFD display flashes

STORED. Then release the memory key.

The indicator which matches the preset

you used will illuminate.

You can use these as a starting point to do your own tweak-

ing or for quick push-a-button-and-be-done setup.

AMP1

AMP2

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

Each preset stores

all the values for

each of the

Memory-2 sets the amplifier up with a 24 dB per octave

low-pass crossover at 80 Hz, an infrasonic filter (often called

subsonic filter) to protect the speakers from harmful ultra-low

frequencies and a 6 dB bass boost at 40 Hz.

AMP1

AMP2

* kicker *

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

Any preset you store will replace the ones that come from

the factory. You can reset all four preset back to factory

defaults anytime simply by doing a reset in the RESET AMP

menu.

MEM-1

MEM-2

MEM-3

MEM-4

stored

MEM-1

MEM-2

MEM-3

MEM-4

following amplifier

controls:

RECALLING A PRESET

Memory-3 sets the amplifier up with a 24 dB per octave

low-pass crossover at 80 Hz, an infrasonic filter (often called

subsonic filter) to protect the speakers from harmful ultra-low

frequencies, a 6 dB bass boost at 40 Hz and sets the

Kompressor into CONTOUR mode.

PRESS &

RELEASE

PRESETS

INDICATORS

*.) GAIN

*.) EQ

*.) LO-PASS

*.) HI-PASS

*.) PHASE

*.) MUTE

To recall a memory preset simply press

and release the key. The matching

indicator will light up and the amplifier will

change all the corresponding controls to

the values assigned to the memory pre-

set.

Here are the settings in each preset from the factory.

MEMORY-1 MEMORY-2 MEMORY-3 MEMORY-4

AMP1

AMP2

GAIN LEVEL

6 DB

M1 M2 M3 M4

LOCK LEFT SYS RIGHT MUTE

GAIN EQ LPF HPF PHASE KOMP

EQ FREQUENCY 40 HZ

40 HZ

+ 6 DB

40 HZ

+ 6 DB

40 HZ

+ 6 DB

* kicker *

MEM-4

MEM-1

MEM-2

MEM-3

EQ BOOST/CUT

EQ BANDWIDTH

FLAT

Memory-4 sets the amplifier up with a 24 dB per octave

low-pass crossover at 80 Hz, an infrasonic filter (often called

subsonic filter) to protect the speakers from harmful ultra-low

frequencies, a 6 dB bass boost at 40 Hz and sets the

Kompressor into RED-LINE mode.

ESC

ENT

HOME

*.) KOMPRESSOR

LO-PASS SLOPE 24 dB

24 DB

80 HZ

24 DB

25 HZ

24 DB

80 HZ

24 DB

25 HZ

24 DB

80 HZ

24 DB

25 HZ

This gives you the

ability to dial in four

LO-PASS FREQ

HI-PASS SLOPE

HI-PASS FREQ

PHASE L&R CH.

MUTE L&R CH.

80 HZ

24 DB

25 HZ

completely different amplifier settings and store them in pre-

sets for instant recall later.

As stated before you can always start with one of these

presets, tweak it to fit your installation and then save your

settings into a new preset.

0 DEGREE 0 DEGREE O DEGREE O DEGREE

OFF

CONTOUR RED-LINE

0 DB 0 DB

OFF

It’s like a preset for your favorite radio stations...only better!

KOMPRESSOR

KOMP ADJ.

OFF

0 DB

SX .1 Series Amplifiers

€Alternator noise (whining sound that varies with engine RPM):

¬Check for damaged RCA cables.

¬Check routing of RCA cable.

¬Check source unit for good ground.

¬Check GAIN RANGE in SYSTEM menu, turn down if set too

high.

¬Substitute known good source unit.

Troubleshooting

;If amp does not make noise using PINK NOISE then:

If your amplifier does not appear to be working, check obvi-

ous things first such as blown fuses, poor or incorrect wiring

connections, crossovers set improperly, gain controls

improperly set, etc.

¬Check speaker connections.

¬Test speaker outputs with known good speaker.

€Other Symptoms:

¬Check GAIN in MAIN MENU, turn down if set too high.

;Amp is very hot, no output.

There are two LEDs on the end panel of your KICKER SX

series amplifier, one green and one red. The green LED indi-

cates the amplifier is turned on. The red LED indicates that

there is a fault condition with the end panel fuses and they

need checked.

¬Thermal protection is engaged. Check SICK BAY to

verify. Check for proper impedance at speaker

terminals. Also check for adequate airflow around

amplifier.

CAUTION: When jump-starting the vehicle, be sure

that connections made with jumper cables are cor-

rect. Improper connections (+ to - & - to +) will

result in blown amplifier fuses as well as failure to

other systems in the vehicle.

;Amp shuts down while vehicle is running.

¬Over Voltage protection engaged. Check SICK BAY

to verify. Voltage to the amplifier is not within the

9-16 volt operating range. Have automobile

charging/electrical system inspected.

The power indicator on top of the amplifier which illumi-

nates the model badge follows the same function as the

green LED.

If you have more questions about the installation and oper-

ation of your new KICKER amplifier, see the Authorized KICKER

Dealer in your area. You may also call our Technical Services

Line at (405)624-8583 for assistance or visit our website at

www.KICKER.com

;Amp only plays at low volume levels.

€Green LED ooff, no output:

¬With a Volt Ohm Meter (VOM) check:

¬+ 12 volt power terminal (should read +12V to +16V).

¬Remote turn-on terminal (should read +12V to +16V).

¬Ground terminal to chassis ground (should read 0).

¬Short circuit protection engaged. Check SICK BAY

to verify. Check for speaker wires shorted to each

other or the vehicle chassis. Damaged speakers or

operating amplifier below minimum recommended

impedance will also cause this.

;Weak bass output.

€Green LED oon, no output:

¬Change the phase of the LEFT channel in the PHASE

menu. If bass improves then one speaker channel is

out of phase (polarity). You can leave PHASE changed

for this channel to fix the problem or better yet;

Check speaker connections to amp and speakers to

determine which one is wrong and correct. Be sure

to set the PHASE of the LEFT channel back to original

setting after correcting wiring connections.

¬Check amp status in SICK BAY.

¬Check GAIN RANGE in SYSTEM menu.

¬Check GAIN LEVEL in GAIN menu.

¬Check if MUTE is activated.

¬Test amp using PINK NOISE in SICK BAY menu.

;If amp makes noise using PINK NOISE then:

¬Check RCA cable and connections.

¬Check for signal on RCA cable with VOM in AC

position.

SX .1 Series Amplifiers

Kompressor

Here is a brief explanation of each KOMPRESSOR setting.

Performance

Model

SX650.1

SX1250.1

Contour- This preset applies expansion below the threshold

point to provide a fuller sound at lower volume levels. Effect

decreases at higher volume levels. Nice effect for someone

wanting a fuller sound at low to moderate listening levels.

RMS Power

In Watts, All Channels Driven

@ 13.8V, 4Ω Mono, 1.5% THD

@ 13.8V, 2Ω Mono, 1.5% THD

@ 13.8V, 1Ω Mono, 1.5% THD

325 x 1

650 x 1

625 x 1

1250 x 1

ATTACK- This preset applies expansion above the threshold

point to provide a nice quick punch or attack to the music.

Effect increase with higher volume levels. Like music with a

quick and punchy sound? Give this one a try.

Dynamic Power

In Watts, All Channels Driven

Red-line- Provides a quick clamp to dynamic peaks while

still allowing a full sound to come through. Effect increases

at higher volume levels. Like to play it loud but want to

protect your speakers? Want low level details to come

through over road noise? Want a more even volume level to

your music? All can be achieved with this preset.

@ 14.4V, 4Ω Mono, 1.5% THD

@ 14.4V, 2Ω Mono, 1.5% THD

@ 14.4V, 1Ω Mono, 1.5% THD

325 x 1

650 x 1

625 x 1

1250 x 1

Length With EndKaps

16”

(40.64cm)

22.50”

(57.15cm)

OFF- Pretty much says it all. This turns the KOMPRESSOR

off. This is the factory default setting.

Fusing

30A x 2

4 GA

150A x 1 external

2 GA

After selecting your KOMPRESSOR setting you can adjust its

effect using the KOMPRESSOR ADJUSTMENT (KOMP ADJ.)

setting located in the SYSTEM menu. There you can change

the threshold point for each of these settings to customize

the KOMPRESSOR effect to fit your speakers, car or personal

tastes.

Recommended Power & Ground Wire

The possibilities are almost endless! Tweak away!

SX .1 Series Amplifiers

Height:

2.5 inches / 6.35 centimeters

10 inches / 25.4 centimeters

Subtract 5 inches (12.7 cm) from chart above

20 Hz - 200 Hz, +0 / -1 dB

62.5 mV - 16 V

WHAT IS NOT COVERED?

ELECTRONICS LIMITED WARRANTY

Width:

This warranty is valid only if the product is used for the purpose for which it

Kicker warrants this product to be free from defects in material and workman-

ship under normal use for a period of 90 DAYS from date of original purchase

with receipt. When purchased from an Authorized KICKER Dealer it is warranted

for TWO (2) YEARS from date of original purchase with receipt. If the product

is labeled “B Stock” it is warranted for 90 DDAYS from date of original purchase

with receipt. If labeled “B SStock” and purchased from an Authorized KICKER

Dealer, it is warranted for ONE ((1) YYEAR from date of purchase with receipt. In all

cases you must have the original rreceipt! Should service be necessary under this

warranty for any reason due to manufacturing defect or malfunction during the

warranty period, Kicker will replace or repair (at its discretion) the defective mer-

chandise with equivalent merchandise at no charge. Warranty replacements on

“B-Stock” merchandise may have cosmetic scratches and blemishes.

Discontinued products may be replaced with more current equivalent products.

This warranty is valid only for the original purchaser and is not extended to

owners of the product subsequent to the original purchaser. Any applicable

implied warranties are limited in duration to a period of the express warranty as

provided herein beginning with the date of the original purchase at retail, and

no warranties, whether express or implied, shall apply to this product thereafter.

Some states do not allow limitations on implied warranties, therefore these

exclusions may not apply to you.

was designed.

It does not cover:

Damage due to improper installation.

Subsequent damage to other components.

Damage caused by exposure to moisture, excessive heat, chemical cleaners,

and/or UV radiation.

Damage through negligence, misuse, accident or abuse. Repeated returns for

the same damage may be considered abuse.

Any cost or expense related to the removal or reinstallation of product.

Speakers damaged due to amplifier clipping or distortion.

Items previously repaired or modified by any unauthorized repair facility.

Return shipping on non-defective items.

Products with tampered or missing barcode labels.

Products returned without a Return Authorization (RMA) number.

Freight Damage.

The cost of shipping product to Kicker.

Service performed by anyone other than Kicker.

Speaker with any foreign caulk used for gasket material.

Length Without EndKaps:

Frequency Response:

Input Sensitivity:

Signal-t0-Noise Ratio:

•

>98 dB

High Pass Crossover Freq.: 10 Hz - 60 Hz in 1 Hz steps

•

High Pass Crossover Slope: 0 (off) - 24 dB in 6 dB steps

Low Pass Crossover Freq.:

30 Hz - 200 Hz in 1 Hz steps

•

Low Pass Crossover Slope: 0 (off) - 48 dB in 6 dB steps

KickEQ Frequency:

KickEQ Bandwidth (Q):

KickEQ Boost/Cut:

20 Hz - 200 Hz in 1 Hz steps

.5 to 10 in .5 steps

+/- 18 dB per Octave

Remote Bass Level Control: Included with each amplifier

Power & Ground Terminals: Will accept up to 2 Gauge wire

DSP Reaction Time / Delay: 0.7 milliseconds ^{(In other Words...Real Fast!)}

Friend’s Reaction:

Stranger’s Reaction:

This warranty gives you specific legal rights; however you may have other

rights that vary from state to state.

WHAT TO DO IF YOU NEED WARRANTY OR SERVICE

That Shizzle's Off The Hizzle

Dude...Sweet...

HOW LONG WILL IT TAKE?

Kicker strives to maintain a goal of 24-hour service for all returns.

Delays may be incurred if lack of replacement inventory or parts is

encountered.

Defective merchandise must be returned to your local Authorized Stillwater

Designs (Kicker) Dealer for warranty. Assistance in locating an Authorized Dealer

can be obtained by writing or calling Stillwater Designs direct. You can confirm

that a dealer is authorized by asking to see a current authorized dealer window

decal.

INTERNATIONAL WARRANTY

Contact your International Kicker dealer or distributor concerning specific

procedures for your country’s warranty policies.

If it becomes necessary for you to return defective merchandise, call the

Kicker Customer Service Department at (405)624-8510 for a Return Authorization

(RMA) number. Package all defective items in the original container or in a pack-

age that will prevent shipping damage, and return to

Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075

The RMA number must be clearly marked on the outside of the package.

Return only defective components. Return of entire cabinets, system packs,

pairs, etc. increases your return freight charges. Non-defective items received

will be returned freight collect.

P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • 405 624-8510

Include a dated proof-of-purchase stating the Customer name, Dealer

name, product purchased and date of purchase. Warranty expiration on items

without proof-of-purchase will be determined from type of sale and the manu-

facturing date code. Freight must be prepaid; items received freight collect will

be refused.

Failure to follow these steps may void your warranty. Any questions can be

directed to the Kicker Customer Service Department at (405)624-8510.

KICKER drivers are capable of producing sound levels

that can permanently damage your hearing! Turning

up a system to a level that has audible distortion is

more damaging to your ears than listening to an

undistorted system at the same volume level. The

threshold of pain is always an indicator that the sound

WARNING:

level is too loud and may permanently damage your

hearing.

Please use common sense when controlling volume!

April 2003

SX .1 Series Amplifiers

Notes

Chic’s Numbers

Pizza Delivery

Hook Ups

SX .1 Series Amplifiers

Pyramid Car Audio PDVD79 User Manual
Pioneer Car Stereo System DEH X3500UI User Manual
Pentax C70210HK User Manual
Oster Blender Oster BLSTDG Series User Manual
Orion PARAGON 5360 User Manual
Olympus 227630 User Manual
KitchenAid KSB465 User Manual
KitchenAid 4KFP720BU0 User Manual
JVC TK C9300U User Manual
JVC KW XC777 User Manual