Features
ꢀ Newly Designed Passive Crossover Network allows
detailed imaging and pin-point sound staging of the critical high
frequencies.
ꢀ High-Power Tinsel Lead Wires eliminate broken leads and
power loss, due to the common use of “insufficient-gauge” lead
wires.
ꢀ Aluminum Dome Tweeter with Neodymium Magnet
featured in the KS25 provides a smooth high frequency
response with fast, detailed and spatially-correct imaging.
ꢀ Felt Damping Plug behind the Tweeter’s Diaphragm
dissipates standing waves, quickens spectral decay and
improves the transient response of the driver.
ꢀ Titanium Dome Tweeter with Neodymium Magnet
featured in the KS20 provides a polished high frequency
response with agile, meticulous and spatially-correct imaging.
ꢀ High-Temp Polyimide Film Voice Coil Former
improves sonic and conductive properties, and prevents
thermal-electrical meltdown.
ꢀ PEN™ Dome Tweeter with Neodymium Magnet
featured in the KS13 provides a silky high frequency response
with quick, precise and spatially-correct imaging. PEN is an
acronym for the space age material “biaxially oriented
polypropylene naphthalate film”--your parents’ tax dollars
probably paid for its development, you might as well enjoy it.
ꢀ Ferro-Fluid™ cooled tweeter voice-coil extends the high
frequency transducer’s life span.
Note: To get the best performance from your Kicker KS-Series System Components,
we recommend using genuine Kicker Accessories and Wiring.
3
KS-Series Tweeters
Performance
KS13
Model:
KS20
KS25
Speaker Design
High Frequency Transducer High Frequency Transducer High Frequency Transducer
Rated Impedance, ohm
DC Resistance, ohm
4
4
4
3
3
3
Sensitivity [SPLo], dB @ 1W, 1m
Resonance Frequency [fo], Hz
Power Range, Watts RMS
Peak Power Handling, Watts
Effective Frequency Range, Hz
Top-Mount Depth, in (cm)
Mounting Hole Diameter, in (cm)
Frame Diameter, in (cm)
Overall Depth, in (cm)
Tweeter Size, in (cm)
92
92
94
2970
1770
1560
6-75
6-95
6-150
150
190
300
4500-21k
9/16 (1.4)
1 9/16 (3.98)
1 31/32 (5.0)
27/32 (2.15)
1/2 (1.3)
Dome
4500-21k
9/16 (1.4)
1 9/16 (3.98)
1 31/32 (5.0)
27/32 (2.15)
3/4 (2.0)
Dome
3500-22k
15/32 (1.2)
1 15/16 (4.88)
2 11/32 (5.9)
1 1/16 (2.65)
1 (2.54)
Dome
Tweeter Design
Tweeter Diaphragm Material
Tweeter Magnet Material
Outboard Crossover
PEN
Titanium
Neodymium
Included
Included
12, 4500
Yes
Aluminum
Neodymium
Included
Included
18, 4500
Yes
Neodymium
Included
Included
12, 4500
Yes
Speaker Wire
High Pass, dB, at Frequency, Hz
Grills Included
If you have any questions about the installation of your Kicker KS-Series Tweeters, see the Authorized Kicker Dealer where you made your purchase. For more advice on
installation, click on the SUPPORT tab on the Kicker homepage, www.kicker.com. Choose the Technical Support tab, choose subject you are interested in, and then
download or view the corresponding information. Please E-mail [email protected] or call Technical Services (405) 624-8583 for specific or unanswered questions.
4
KS-Series Tweeters
Installation
Tweeter Mounting
If custom door mounting locations for the KS-Series Tweeters are desired, be careful to avoid interference from the window and
door lock mechanisms. The first step is to find a location on the door panel that will accept the dimensions of the speaker. Then
remove the door panel from the door, and check for operational clearance of the window. Cycle the window all the way down and up.
If metal must be cut to mount the speakers, avoid structural metal and braces. An optional reinforcing panel (thin piece of wood or
Medium Density Fiberboard) may be necessary if the door panel cannot support the mounting of the speaker. Mount the speaker to
the door panel and door body as outlined in Figure 1.
If the factory door speaker wiring is not available, it will be necessary to run the supplied wire through the door jamb. The speaker
wire should be kept away from sharp edges and avoid the possibility of getting pinched by the door. An existing grommet in the door
jamb is the ideal place to run the speaker wire. If the factory hole and grommet do not exist or are inaccessible, you must drill a hole
to run the speaker wire through the door jam. Be careful not to drill into other wiring or existing door mechanisms. Any time a wire is
run through a hole, it is necessary to insert a rubber or plastic grommet to protect the wire from damage as outlined in Figure 2.
Figure 1
Figure 2
The tweeter can be mounted one of three ways:
flush, surface and angled mounting. For flush
mounting applications, please refer to the illustration
in Figure 3 and 4. Mount the tweeter as high up on
the door and as far forward as possible without
interference from the dashboard. Choose a flat
location on the door with space behind the panel to
allow room for the mounting nut.
(Optional)
Stagger Holes
For Wiring &
Use Grommets
(When Factory Holes and
Grommets are not Available)
Door Panel
To Crossover
Kick Panel
After checking the clearances, cut the appropriate
mounting hole diameter in the door panel. Place the
mounting nut behind the door panel. Feed the wire through the door and body panels. Mount the tweeter by screwing the tweeter onto
the mounting nut.
For surface mounting applications, remove the tweeter face plate by screwing it off and install the supplied smaller face plate. Use
the surface mount cup as a template and drill a 7/64” (2.8 mm) hole in the center for attaching the cup to the door and a 5/16”
(7.9 mm) hole for the wires. A #8 flathead sheet metal screw is supplied to attach the surface mount cup to the door panel. Position
the tweeter over the surface mount cup and press it into position.
For angled mounting applications use the back angle ring behind the panel and the front angle ring in front of the panel, and place
the tweeter through the front angle ring and then into the panel. Next place the back angle ring over the tweeter and line up the
narrow part of the front angle ring for proper operation. Attach the longer tweeter mounting nut but do not completely tighten. Rotate
KS-Series Tweeters
5
Installation
all the parts in unison until the tweeter is angled in the desired direction. Secure the assembly by tightening the longer tweeter
mounting nut, as outlined in Figure 5.
Figure 3
Figure 4
Clearance Hole 2.5"
Shorter
Tweeter
Mounting
Nut
Door Body
Mounting Nut
Tweeter
Wire
Tweeter
Door Panel
Panel
2" Hole
Wiring
There are two lengths of wires attached to the Kicker KS-Series Tweeter Crossover. One set is labeled “INPUT” and is designed to
connect to the source unit or amplifier. The other set is labeled “KSxx TWEETER” and is designed to connect to the tweeter’s length
of wires, using the supplied butt connectors. Please see Figure 6.
Figure 6
Figure 5
Tweeter
Butt
Connectors
+
Back
Angle
_
Ring
Longer
Tweeter
Mounting
Nut
Tweeter
SOURCE UNIT or AMPLIFIER
Wire
_
_
Front
Angle
Ring
107.5 FM THE END
Panel
+
+
All specifications and performance figures are subject to change. Please visit kicker.com for the most current information.
6
KS-Series Tweeters
WHAT IS NOT COVERED?
Acoustics LIMITED WARRANTY
This warranty is valid only if the product is used for the purpose for which it was
designed.
It does not cover:
Kicker warrants this product to be free from defects in material and workmanship
under normal use for a period of THREE (3) MONTHS from date of original
purchase with receipt. When purchased from an Authorized KICKER Dealer it is
warranted for ONE (1) YEAR from date of original purchase with receipt. In all cases
you must have the original receipt! Should service be necessary under this
warranty for any reason due to manufacturing defect or malfunction during the
warranty period, Kicker will repair or replace (at its discretion) the defective
merchandise with equivalent merchandise at no charge. Warranty replacements
may have cosmetic scratches and blemishes. Discontinued products may be
replaced with more current equivalent products.
•
•
•
Damage due to improper installation.
Subsequent damage to other components.
Damage caused by exposure to moisture, excessive heat, chemical cleaners,
and/or UV radiation.
Damage through negligence, misuse, accident or abuse. Repeated returns for
the same damage may be considered abuse.
•
•
•
•
•
•
•
•
•
•
Any cost or expense related to the removal or reinstallation of product.
Speakers damaged due to amplifier clipping or distortion.
Items previously repaired or modified by any unauthorized repair facility.
Return shipping on non-defective items.
Products with tampered or missing bar code labels.
Products returned without a Return Authorization (RMA) number.
Freight Damage.
This warranty is valid only for the ORIGINAL PURCHASER and is not extended
to owners of the product subsequent to the original purchaser. Any applicable
implied warranties are limited in duration to a period of the express warranty as
provided herein beginning with the date of the original purchase at retail, and no
warranties, whether express or implied, shall apply to this product thereafter. Some
states do not allow limitations on implied warranties, therefore these exclusions may
not apply to you. This warranty gives you specific legal rights; however you may
have other rights that vary from state to state..
The cost of shipping product to Kicker.
Service performed by anyone other than Kicker.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
Defective merchandise should be returned to your local Authorized Stillwater
Designs (Kicker) Dealer for warranty. Assistance in locating an Authorized Dealer
can be obtained by writing, calling, or by visiting kicker.com. You can confirm that a
dealer is authorized by asking to see a current authorized dealer window decal.
HOW LONG WILL IT TAKE?
Kicker strives to maintain a goal of 24-hour service for all acoustics (subwoofers,
midrange drivers, tweeters, crossovers, etc) returns. Delays may be incurred if lack
of replacement inventory or parts is encountered.
If it becomes necessary for you to return defective merchandise directly to
Stillwater Designs (Kicker), call the Kicker Customer Service Department at
(405) 624-8510 for a Return Authorization (RMA) number. Package all defective
items in the original container or in a package that will prevent shipping damage,
and return to:
INTERNATIONAL WARRANTY
Contact your International Kicker dealer or distributor concerning specific
procedures for your country’s warranty and service policies.
Stillwater Designs, 5021 North Perkins Road, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please
return only defective components (tweeter, crossover, plug, etc.). The return of
functioning items increases your return freight charges. Non-defective items
received will be returned freight collect.
P.O. Box 459 • Stillwater, Oklahoma 74076 • U.S.A. • (405) 624-8510
KICKER drivers are capable of producing sound levels
that can permanently damage your hearing! Turning up a
system to a level that has audible distortion is more
damaging to your ears than listening to an undistorted
system at the same volume level. The threshold of pain
Include a copy of the original receipt with the purchase date clearly visible, and a
“proof-of-purchase” statement listing the Customer’s name, Dealer’s name and
invoice number, and product purchased. Warranty expiration on items without proof-
of-purchase will be determined from type of sale and the manufacturing date code.
Freight must be prepaid; items sent freight collect, or COD, will be refused.
is always an indicator that the sound level is too loud and
WARNING:
may permanently damage your hearing.
Failure to follow these steps may void your warranty. Any questions can be
directed to the Kicker Customer Service Department at (405) 624-8510.
Please use common sense when controlling volume!
08112005+05KS
7
KS-Series Tweeters
|