Instruction Manual
Underwater Case
PT-023
For the digital camera
CAMEDIA C-8080 Wide Zoom
■ Thank you for buying the Underwater Case PT-023.
■ Please read this instruction manual carefully and use the product safely
and correctly.
■ Please keep this instruction manual for reference after reading it.
■ Wrong use may cause damage to the camera on the inside from water
leakage, and repair may not be possible.
■ Before use, perform an advance check as described in this manual.
1. Keep this product out of the reach of babies, infants, and children.
There is the possibility of occurrence of the following types of
accidents.
ț Injury by dropping onto the body from a height.
ț Injury from parts of the body getting caught in parts which open
and close.
ț Swallowing of small parts. Please consult a physician immediately
if any parts have been swallowed.
ț Triggering of the flash in front of the eyes may cause permanent
vision impairment etc.
2. Do not store with a battery in the digital camera housed in this
product. Storage with a battery inserted may lead to leakage of the
battery liquid and fire.
3. If leakage of water should occur with a camera installed in this
product, quickly remove the battery from the camera. There is the
possibility of ignition and explosion from generation of hydrogen gas.
4. This product is made of resin. There is the possibility that injuries
may be caused when it becomes broken because of strong impact
with a rock or other hard objects. Please handle with sufficient care.
5. The silica gel and the grease for silicone O-rings for this product
are not edible.
CAUTION
1. Do not disassemble or modify this product. This may cause water
leakage or trouble. In case of disassembly or modification by
persons other than those appointed by OLYMPUS CORPORATION,
the guarantee shall not apply.
2. Do not place this product at locations with abnormally high or
abnormally low temperatures or at locations with extreme
temperature changes. The product may deteriorate.
3. Opening and closing at locations with much sand, dust, or dirt may
impair the waterproof characteristic and cause water leakage. This
should be avoided.
4. This product has been designed and manufactured for use at a
water depth within 40 m. Please note that diving to a depth in
excess of 40 m may cause permanent deformation or damage to
the Case and the camera inside the Case or may lead to water
leakage.
E-2
5. Rough handling, such as jumping into the water with the case in
your hand or in an outside pocket or throwing the case into the
water, etc. could lead to water leakage. Please always take care
when using the case.
6. If the camera contained in the case becomes wet because of water
leakage, etc., immediately wipe off all moisture and check the
camera is working correctly.
7. Before travelling by air, please make sure you remove the O-ring,
otherwise the difference in air pressure may make it impossible to
open the case.
8. To ensure safe and trouble-free handling and operation of the
digital camera in this product, please read the camera’s instruction
manual carefully.
9. When sealing this product, please take care to ensure no foreign
matter such as sand, dirt or hair are on the O-ring or contact
surfaces.
Batteries
● Use an exclusive lithium-ion battery (Olympus BLM-1) designed for
digital cameras.
● Keep the battery's contacts away from damp or humidity; otherwise
this could impair performance and/or cause accidents.
● For additional battery cautions, refer to your digital camera's
instruction manual.
● The Power Battery Holder for the C-8080 Wide Zoom (optional B-
HLD30) cannot be used with this product.
E-3
For Prevention of Water Leakage Accidents
When water leakage occurs while this product is being used, repair of
the camera housed in this product may become impossible. Please
observe the following cautions for use.
1. When sealing this product, make sure that no hairs, fibers, sand
particles or other foreign matter stick not only to the O-ring, but
also to the contact surface. Even a single hair or a single grain of
sand may cause water leakage. Please check with special care.
Examples for foreign matter sticking to the O-ring
Hair
Fibers
Grains of sand
2. The O-ring is a consumption product. Please replace it at least
once a year by new one. Also perform maintenance for every use.
3. Deterioration of the O-ring will progress according to the use
conditions and the storage conditions. Immediately replace the O-ring
by a new one if it is damaged, shows cracks, or has lost its elasticity.
4. At the time of O-ring maintenance, clean the inside of the O-ring
groove and confirm the absence of dirt, dust, sand, and other
foreign matter.
5. Apply the specified silicone O-ring grease to the O-ring.
6. The waterproof function is not effective when the O-ring is not
installed correctly. When installing the O-ring, take care that it does
not project from the groove and that it is not twisted. Also, when
sealing the Case, close the lid after confirming that the O-ring has
not come out of the groove.
7. This product is an airtight construction made of plastic (polycarbonate).
When it is left for a long time in a car, on a boat, at the beach, or at
other places reaching a high temperature, or when it is subjected for a
long time to uneven external force, it may be deformed and the
waterproof function may be lost. Pay sufficient attention to temperature
control. Also do not place heavy objects onto the product during
storage or transport, and avoid unreasonable storage.
8. When the O-ring contact surface is pressed strongly from the
E-4
outside of the Case, or when the Case is twisted, the waterproof
function may be lost. Take care not to exert excessive force.
9. Please be sure to perform the advance test and the final test each
time before using the case.
10.If you should notice drops of water or other signs of water leakage
while taking pictures, immediately stop the dive, remove any water
from the camera and the product, test according to the item "Final
check", and confirm whether leakage has occurred or not.
Handling the Product
● Use or storage of the product at the following locations may cause
defective operation, defects, trouble, damage, fire, internal
clouding, or water leakage. Always avoid these locations.
ț Places where high temperatures exist, such as in direct sunlight, in
a closed vehicle, etc., and/or where extreme differences in
temperatures exist.
ț Places where there is a lot of dust.
ț Places where there are open fires.
ț Places subject to vibrations.
ț Places where volatile chemicals are stored or used.
ț Water deeper than 40 meters.
● This product is made of polycarbonate resin with excellent impact
resistance, but it may be damaged by scraping against rocks etc. It
also may break when it hits hard objects or is dropped.
● This product is not a case to soften impacts to the camera inside the
product. When this product with a digital camera inside it is subjected
to impacts or heavy objects are placed onto it, the digital camera may
become damaged. Please handle the product with sufficient care.
● When the product is not used for a long time, the waterproof
performance may drop because of deterioration of the O-ring etc.
Before use, always perform the advance test and the final check.
● Do not apply excessive force to the port mount, TTL cable
connector, diffusion plate, tripod socket, etc.
● When a flash is used while the Case is being used, shadows may
appear at the edges of the picture. This is especially notable when
taking pictures in macro mode on the wide-angle side. Please use
a flash after image confirmation.
●
Do not use the following chemicals for cleaning, corrosion prevention,
prevention of fogging, repair or other purposes. When these are used
for the Case directly or indirectly (with the chemicals in vaporized state),
they may cause cracking under high pressure or other problems.
E-5
Explanation
Chemicals which cannot be used
Do not clean the Case with alcohol, gasoline, thinner
or other volatile organic solvents or with chemical
detergents etc. Pure water or lukewarm water is
sufficient.
Volatile organic solvents,
chemical detergents
Do not use anticorrosion agents. The metal parts use
stainless steel or brass, and washing with pure water
is sufficient.
Anticorrosion agent
Commercial defogging
agents
Do not use commercial defogging agents. Always
use the specified desiccant silica gel.
Use only the specified silicone grease for the silicone
O-ring, as otherwise the O-ring surface may
deteriorate and water leakage may be caused.
Grease other than specified
silicone grease
Do not use adhesive for repairs or other purposes.
When repair is required, please contact a dealer or a
service station of our company.
Adhesive
● Do not perform operations other than specified in this instruction
manual, do not remove or modify parts other than specified, and do
not use parts other than specified.
Any troubles in taking pictures or with the equipment resulting from
the above actions shall be outside the guarantee.
● OLYMPUS CORPORATION shall be in no way responsible for
accidents involving immersion of a digital camera in water.
● OLYMPUS CORPORATION shall not pay any compensation for
accidents (injury or material damage) at the time of use.
● When the enclosure of the balance weight breaks, the metal on the
inside may corrode. Take care not to damage the enclosure.
● After use, wash the balance weight with pure water and wipe off all
moisture sufficiently.
E-6
Contents
Disclaimer ..................................................................................E-1
Please read the following before using the product ..................E-1
For safe use ..............................................................................E-1
Batteries ....................................................................................E-3
For Prevention of Water Leakage Accidents..............................E-4
Handling the Product..................................................................E-5
Contents ..............................................................................E-7-8
1. Preparations ......................................................................E-9
Check the contents of the package. ..........................................E-9
Names of the parts................................................................E-10
Install the strap..................................................................... E-11
Master the basic operation. .................................................... E-11
Holding the Case ..................................................................E-11
How to Press the Shutter......................................................E-12
How to Use the Mode Dial ....................................................E-12
How to Use the Zoom Lever ................................................E-12
Setting the Zoom Lever ........................................................E-13
Power Switch Button Operation Method ..............................E-13
Popping up the Flash............................................................E-13
Removing/attaching the standard port..................................E-14
Detaching/attaching the diffusion plate ................................E-15
Removing the TTL cable connector cap ..............................E-16
Removing the hot shoe cable cap ........................................E-17
Cleaning the TTL connector..................................................E-18
2. Advance Check of the Case ......................................E-18
Advance test before use ..........................................................E-18
Making sure the case is waterproof ......................................E-18
Advance Test........................................................................E-19
3. Install the digital camera. ............................................E-20
Check the digital camera......................................................... E-20
Battery Confirmation ............................................................E-20
Confirmation of the Remaining Number of Pictures to be Taken........E-20
Removing the carrying strap and lens cap from the digital camera......E-20
Removing the filter from the digital camera ....................................E-20
Setting the camera mount on the digital camera..............................E-21
Loading in the Case ................................................................E-21
Which digital cameras can be loaded? ................................ E-21
Check the operation of the camera. .................................... E-21
Open the Case. ...................................................................... E-21
Lifting the mode dial knob ....................................................E-21
Load the digital camera. ...................................................... E-22
E-7
Fitting the mode dial knob ....................................................E-22
Insertion of silica gel ............................................................E-22
Check the loading status......................................................... E-23
Seal the Case...........................................................................E-23
Install the special balance weight.............................................E-24
Installation and Removal of the LCD Hood..............................E-24
Installation ............................................................................E-24
Removal................................................................................E-24
Mounting and Removing the Lens Cap....................................E-25
Perform the final checks. ........................................................ E-25
Visual Inspection ..................................................................E-25
Setting the camera power to ON and OFF. ..........................E-25
Try to move the mode dial. .................................................. E-25
Final Test ................................................................................E-26
4. Taking Pictures Under Water ....................................E-27
How to Use the Hand Strap ....................................................E-27
Take pictures carefully. .......................................................... E-27
Confirm the picture on the LCD monitor. ..............................E-27
Quietly press the shutter lever. ............................................ E-27
Caution when using the flash................................................E-27
5. Handling After Shooting..............................................E-28
Wipe off any waterdrop. ..........................................................E-28
Take out the digital camera..................................................... E-29
Wash the Case with pure water. ............................................ E-30
Dry the Case. .......................................................................... E-30
6. Maintaining the Waterproof Function ....................E-31
Remove the O-ring...................................................................E-31
Remove any sand, dirt, etc. .................................................... E-31
Install the O-ring. .................................................................... E-32
How to Apply Grease to the O-ring ..........................................E-32
Maintenance of the threaded sections on the
TTL cable and TTL cable connector ........................................E-33
Maintenance of the TTL Connector Cap..................................E-33
Replace consumable products. .............................................. E-34
7. Appendix ..........................................................................E-35
Q & A on the use of the PT-023 ..............................................E-35
After-sale Service ....................................................................E-40
Specifications ..........................................................................E-41
Diver's Insurance Guide ..........................................................E-41
E-8
1. Preparations
Check the contents of the package.
Check that all accessories are in the box.
Contact your dealer if accessories should be missing or damaged.
Silicone grease
Silica gel
LCD hood
(on the body)
TTL cable connector
(waterproof cap)
LCD hood
strap
Buckle opener
Waterproof cap
maintenance adapter
Hand strap
Standard port
(Attached to the main body)
Lenscap
Balance weight
Case body
Pick for O-ring removal
(Check that the O-ring is normal.)
Instruction manual
(this manual)
Warranty card
Diver's insurance guide
保
証
書
WARRANTY
（販売店控え）
取扱説明書
本保証書は、本記載内容で無料修理を行うことをお約束するものです。
お買い上げの日から下記期間中、万一故障が発生した場合は、本契約書を添付ご持参の上
お買い上げ販売店、または当社サービスステーションにご依頼ください。
デジタルカメラ
CAMEDIA C-8080 Wide Zoom用
本保証書は日本において有効です。
This is limited warranty for
year from your date of
purchase. Useful only in
Japan.
期 間
お買上げ
本体1年間
年 月
a
1
日
防水プロテクタ
住所 Address
お客様
氏名 Name 性別（男・女）、年齢（ 才）
Customer
PT-023
様
TEL
(
)
〔必ず店名印を押
してください。〕
販売店
Dealer's
name and
address
JAPAN
品名
防水 防塵
型名
・
プロテクタ Model
Serial NO.
■このたびは、防水プロテクタPT-023をお買上げいただき、ありがとうご
ざいます。
保証責
任者
保証履行者
〒192-0032 東京都八王子市石川町2951
お問い合せ先/サービスステーション
03（3292）1931
■この説明書をよくお読みのうえ、安全に正しくお使いください。また、
この説明書はお読みになった後、必ず保管してください。
■誤った使い方をされると水漏れにより中のカメラが破損し、修理不能
になる場合があります。
■ご使用前には、この説明書に従い、必ず事前チェックを実施してください。
Information disc
CD-ROM
E-9
Names of the parts
Palm grip
❈
❈
Custom button
Self-timer/Remote control/
Erase button
Metering/Print reservation
button
AF/Macro/MF button
Exposure compensation/Data
display button
Flash mode/Rotation
playback button
Front lid
LCD hood strap
Grease for O-rings (White-cap tube)
Silica gel
Balance weight
Pick for removing O-rings
Buckle opener
Lens cap
Buckle open/close lever
Buckle hook
Quick View button
Control dial knob
Standard port O-ring (POL-104)
Waterproof cap maintenance
adapter
LCD monitor window
Camera mount
Flash button
White balance button
Picture quality mode button
Standard port (PPO-04)
Port lock buckles
TTL cable connector
(waterproof cap)
O-ring (POL-023A)
O-ring (POL-023B)
O-ring (POL-023C)
Diffuser plate and diffuser plate
cover
❈
❈
❈
❈
❈
❈
Carrying strap ring
Carrying strap
LCD inner hood
Mounting guide rails
LCD hood
Tripod socket
Lens ring
Lend window
❈
❈
❈
❈
❈
AEL button
❈
❈
❈
❈
Shutter release lever
Zoom lever
LCD monitor button
OK/Menu button
Cross button
❈
❈
❈
Mode dial knob
Power switch button
Accessory mount
Card select button
Rear lid
Note
:
The Case operation parts marked by
❈
corresponds to the operation parts
of the digital camera. When the operation parts of the Case are operated,
the corresponding functions of the digital camera will operate. For details of
the functions, refer to the instruction manual for the digital camera.
E-10
Install the strap.
Install the strap on the Case body.
Installation explanation
Finished installation
Hand strap
Hand strap ring
:
Please install the strap correctly as shown above. OLYMPUS
CORPORATIOM shall bear no responsibility for damage etc. caused
by dropping the Case because of incorrect installation of the strap.
Master the basic operation.
Please master the basic operation of the Case before taking pictures.
Holding the Case
Hold the Case securely with both hands, keep your elbows close to
your body, and hold the Case so that you can confirm the picture on the
LCD monitor of the digital camera through the LCD monitor window of
the Case.
Good example
Bad example
:
•
Do not exert excessive force onto the lens window or the lens ring.
•
Take care not to put your fingers etc. over the lens window
and the flash diffuser.
Note: • Check your image on the LCD monitor. The viewfinder cannot be used
to check the image.
E-11
How to Press the Shutter
When pressing the shutter lever,
press it gently, so that there will
be no movement of the camera.
Note: • For more detailed information on operating the shutter release,
please consult the digital camera’s instruction manual.
How to Use the Mode Dial
The case is equipped with a mode
dial knob that fits on the camera's
mode dial and functions the same
way. After inserting the digital
camera into the case, make sure
that the mode dial knob is operable
before taking any image.
Mode dial
knob
Advice • Please confirm that the mode dial knob has been set securely to
the mode dial of the digital camera. If the mode of the digital
camera does not change when the mode dial knob is operated,
turn the dial while pushing it lightly.
How to Use the Zoom Lever
Zoom operation is possible by
operating the zoom lever of this
Case corresponding to the zoom
lever of the digital camera in the
Case.
E-12
Setting the Zoom Lever
When loading the digital camera in the
Case, fit the projecting part of the zoom
lever of the digital camera into the
recessed part of the zoom lever on the
inside of the Case.
Advice
•
When loading the camera, confirm that the projecting part of
the zoom lever of the camera is properly set to the recessed
part of the zoom lever of the Case.
When the setting is insufficient, the loading of the camera
becomes imperfect and it may not be possible to seal the
Case or zooming may not function. Insufficient sealing will
cause water leakage.
•
Power Switch Button Operation Method
Power switch
button
Press the power switch button
to switch on the camera power
supply.
When the power switch button
is pressed again, the camera
power supply is switched off.
:
• When the digital camera has not been used for about 3
minutes while in the shooting mode, it enters the sleep
mode (standby status). In the sleep mode, the lens returns
to the wide-angle end and no camera operation is possible.
To cancel sleep mode (and return to operation status),
press the shutter button or any other button.
For details, refer to your digital camera's instruction manual.
Popping up the Flash
Press the flash button on the case to
pop up the camera’s flash.
:
• Once the flash is up, it cannot be retracted as long as the
camera is in the case. Remove the camera from the case to
retract the flash.
E-13
Removing/attaching the standard port
The standard port attached to the case should be removed when
the Wide Port for PT-023 (optional PPO-05) is used.
The standard port can be removed and attached as follows.
Removing
1
First wipe any moisture off the case, and then slowly turn
the two buckles on either side of the standard port in the
opening direction (from down to up, in the direction of the
arrows as shown in the figure on the right).
2
3
When the two buckles have been turned by about 110
degrees from down to up, the standard port begins to
separate from the case. (At this time, the diffusion plate also
separates from the case. Be careful not to drop the plate.)
Continue turning the buckles slowly until the
standard port separates completely from the
case(At this time, the diffusion plate also
separates from the case.).
Attaching
A
fter aligning the notch on the standard port’s case
1
mount with the protrusion on the case’s port mount, fit
the standard port into the case. (If you are going to
mount the diffusion plate at this time, see
“Removing/attaching the diffusion plate” on next page.
2
3
Boss
Mount the standard port on the case so that
the bosses on the case fit into the left and
right buckles.
Buckle
Turn the two buckles from up to down until
they stop to secure the standard port.
:
•
If the standard port is attached improperly to the case,
water penetration may result. Also make sure that the
buckles on the left and right of the standard port are
clamped firmly.
❈ Refer to the Wide Port for PT-023's (optional PPO-05) instruction
manual for detailed instructions on using it.
E-14
Detaching/attaching the diffusion plate
The diffusion plate on the case is detachable. Remove the diffusion plate
when using the optional PPO-05 Wide Port or when the diffusion plate is
not necessary. To attach the diffusion plate, follow the procedure below.
Detaching
1
First make sure the case is completely dry. While
gently holding the diffusion plate and standard port,
slowly turn the two buckles on either side of the
standard port by about 110° in the opening direction
(from down to up, in the directions of the arrows).
2
3
Keep turning the buckles gently to separate
the diffusion plate and standard port
completely from the case.
Pull the diffusion plate from the standard port
in the direction of the arrow to separate
them.
Attaching
1
Align the diffusion plate’s rear window
with the case’s diffusion guides
.
2
3
While fitting the diffusion plate mount
the top panel of the standard port into the port
mount hole on the bottom of the diffusion
on
plate, insert the standard port into the case.
Make sure that the diffusion plate is wedged between the front of
the case and the top of the standard port. Then turn the buckles
on either side of the standard port in the direction of the arrows to
secure them. (For details on how to mount the standard port, see
“Detaching/attaching the standard port” on the previous page.)
:
•
The diffusion plate cannot be used when the PPO-05
is mounted.
E-15
Removing the TTL cable connector cap
TTL flash shooting is possible by uncapping the TTL cable connector
on this case (PT-023) and connecting the FL-20 flash case (optional
PFL-01) as described in the following procedure.
TTL flash shooting by combining this case (PT-022) and the case for
FL-20 flash (optional PFL-01):
Remove the TTL cable connector
1
TTL cable
connector cap
Remove.
cap from this case.
❈
The PFL-01 can be used only
with the C-770 Ultra Zoom.
Connect the underwater TTL
cable connector, provided with
the PFL-01, to the TTL cable
connector on this case.
2
Turn counter clockwise.
1
Underwater
TTL cable
2
Insert into the
connector.
Turn the threaded section of the connector
clockwise lightly until it is stopped.
---- How to attach the TTL cable connector cap to the case ----
Make sure there is no foreign matter attached to the O-rings inside
the cap and on the TTL cable connector. To secure the cap, gently
turn it clockwise until it stops.
Gently turn the cap
clockwise until it stops.
Cap
Connector
Check O-rings
Put the cap on the case.
E-16
:
•
If the TTL cable connector cap is loose, water
penetration may result. Be sure to gently turn the cap
until it stops to make sure it is firmly secured.
Do not turn or tighten the TTL cable too hard. If it is
too tight, it may be difficult to loosen and remove it.
❈ Refer to the optional PFL-01's instruction manual for detailed
instructions on using the TTL cable and hot shoe cable.
Removing the hot shoe cable cap
To perform TTL flash shooting when this case is used, connect the
hot shoe cable provided with the optional PFL-01 between the
connector on this case and the C-8080 Wide Zoom's hot shoe.
Turn the hot shoe cable connector cap inside
1
the case counterclockwise to remove it.
Insert the connector of the hot shoe cable into
the case's connector and turn the connector
screws all the way clockwise to connect them
2
firmly.
Insert the cable's hot shoe into the C-8080
Wide Zoom's hot shoe.
3
When not using the hot shoe cable, attach the
hot shoe cable cap to the hot shoe cable
connector inside the case and turn the cap all
4
the way clockwise to attach it firmly.
:
•
Be sure to remove the camera from the case when
inserting the connector of the hot shoe cable into the
case’s connector.
E-17
Cleaning the TTL connector
If the threaded sections of the TTL cable and TTL cable connector
stick to each other, the cable may disconnect from the connector. To
prevent this, apply O-ring silicon grease (provided with this case) to
the threaded sections.
For details, see the maintenance description on page 33 of this
manual.
:
•
If you cannot disconnect the TTL cable, do not use
force to disconnect it. Contact Olympus for support.
2. Advance Check of the Case
Advance test before use
This Case has been the subject of thorough quality control for the parts
during the manufacturing process and thorough function inspections
during the assembly. In addition, a water pressure test is performed
with a water pressure tester for all products to confirm that the
performance conforms to the specifications. However, depending on
the carrying and storage conditions, the maintenance status, etc., the
waterproof function may be damaged.
Before diving, always perform the following advance test and the water
leakage test after installation of the camera.
Making sure the case is waterproof
Check the parts that ensure the case is waterproof.
1. Make sure that the O-ring between the front and rear lids of the
case is attached firmly and the buckle is tightly secured.
2. Make sure that the O-rings between the case and standard port are
attached firmly and that the buckles are tightly secured.
3. Make sure that the O-ring on the TTL cable connector cap is
attached firmly and that the cap is fitted tightly to the connector.
E-18
Advance Test
1. Before installing the digital camera in the Case, immerse the empty
Case to the intended water depth to confirm that there is no water
leakage.
2. Main causes of water leakage are as follows.
ț The O-ring has not been installed.
ț A part of the O-ring or the entire O-ring is outside the specified
groove.
ț O-ring damage, cracks, deterioration or deformation.
ț Sand, fibers, hair or other foreign matter sticking to the O-ring, the
O-ring groove or the O-ring contact surface.
ț Damage to the O-ring groove or the O-ring contact surface.
ț When closing the Case, check for catching of the hand strap and
silica gel after the above causes have been eliminated.
:
• The most suitable method for checking water leakage
is to immerse the Case to the intended water depth.
When this is difficult, water leakage also can be
checked at a shallow depth with no water pressure. Do
not feel that this is troublesome, but perform this test.
• If the advance test should show water leakage with
normal handling, stop using the Case and contact
your dealer or an Olympus service station (listed on
the rear page of this instruction manual).
E-19
3. Install the digital camera.
Check the digital camera.
Check the digital camera before loading it in the Case.
Battery Confirmation
Since the LCD monitor is used for picture confirmation while taking
pictures under water, the battery life becomes short.
Confirm that the remaining battery capacity is sufficient.
Note:• To make sure you aren't prevented from shooting because the
battery runs out, it is recommended that you load a fully-
charged battery before every diving session.
Confirmation of the Remaining Number of Pictures to be Taken
Confirm that the image storage has a sufficient remaining number
of pictures to be taken.
Removing the carrying strap and lens cap from the digital camera
If the digital camera has a carrying strap and lens cap attached, be
sure to remove them before inserting the digital camera into the
case.
:
• If the digital camera is inserted into the case without
removing the carrying strap and lens cap, the case
cannot be closed properly and water penetration may
result.
• Be careful when removing the carrying strap and lens
cap from the digital camera. Olympus will not assume
any liability for any damage that may result from
dropping the camera.
Removing the filter from the digital camera
If the digital camera has a lens filter attached, be sure to remove it
before inserting the camera into the case.
:
• The digital camera cannot be inserted in the case if a
filter is attached to the camera lens. Always be sure
to remove the lens filter.
E-20
Setting the camera mount on the digital camera
Attach the provided camera mount to the tripod
socket of the camera.
:
• Attach the camera mount in the proper direction as
shown in the above figure.
Loading in the Case
Which digital cameras can be loaded?
This product (PT-023) is exclusively used for the CAMEDIA C-8080 Wide Zoom.
Check the operation of the camera.
Confirm the operation according to the instruction manual for the digital camera.
Open the Case.
Insert the buckle opener of the accessory into the buckle opening
lever as shown in the figure (in direction ) Pull the buckle opener
slowly (in direction ). When not using the buckle opener, hold the
buckle opening lever with your thumb and index finger from the side
and pull it up slowly.
①
②
Lifting the mode dial knob
Pull up the mode dial of the case until it
stops, so that it does not interfere with the
mode dial of the digital camera.
E-21
Load the digital camera.
Push the digital camera attached to the camera
mount so that the mount’s guides slide along
the mounting guide rails on the front lid of the
case. Push it as far as it goes.Quietly load the
digital camera into the Case, taking care that
the projecting part of the zoom lever of the
digital camera properly fits into the recessed
part of the zoom lever of the Case.
Mounting guide rails
Guides
:
• Be sure to store the camera flash before loading the
camera in this case.
• After closing the case, make sure that the camera mount
is properly attached to the front lid and rear lid.
Fitting the mode dial knob
After the digital camera has been loaded, push
down the mode dial of the case from the upper
surface of the case and set it so that the lower part
of the mode dial of the case on the inside of the
case fits properly onto the upper part of the mode
dial of the digital camera.
Advice • After properly fitting the case's mode dial knob, turn the knob to
make sure that the camera's mode dial switches before closing the
case tightly.
Insertion of silica gel
Before sealing the Case,
insert the accessory silica
gel bag (for prevention of
fogging) between the
bottom of the camera and
the Case. Insert the bag
with the glued longer side
to the inside.
Pay attention to the orientation.
E-22
:
•
Insert the silica gel all the way at the specified location and
with the specified orientation. When the orientation is not
correct, the silica gel bag will be caught when the Case is
sealed and water leakage will be caused.
•
•
Attempting to seal the Case with the bag inserted only part of
the way will cause the silica gel bag to get caught by the O-ring
and water leakage will occur.
Once silica gel has been used, the moisture absorption
performance will be impaired. Always exchange the silica
gel when the Case is opened and closed.
Check the loading status.
Always perform the following final checks before sealing the Case.
ț
Has the camera been inserted properly so that the zoom lever works?
Has the silica gel bag been placed in the correct position and in the proper
way?
Are both the O-rings and the contact surfaces of the front lid free of dirt and
other foreign matter?
ț
ț
ț
ț
ț
Are the O-rings correctly positioned in the groove of the front and rear lids?
Is the lens port attached properly and are the buckles locked correctly?
the TTL cable connector cap attached tightly?
Seal the Case.
When the rear lid is closed
(quietly, so that the O-ring
will not come out of the
groove), the buckles are
engaged with the edge of
the rear lid, and the buckle
lock levers are pushed down
in arrow direction, the Case
will be sealed airtight.
:
•
Seal the Case by turning both buckle lock levers down in
arrow direction. When one of the buckles is left open, the
Case will not be sealed and water leakage will be caused.
E-23
Install the special balance weight.
Install the special balance weight
to the tripod mounting thread at
the bottom of the Case. Install the
balance weight securely by
tightening the accessory screw of
the balance weight.
Installation and Removal of the LCD Hood
Installation
Strongly push the mounting projections of the LCD hood as shown
in the figure into the guides above and below the LCD monitor
window.
Removal
Remove the mounting projections of the LCD hood from the guides
above and below the LCD monitor window by widening the LCD
hood.
Guides
Installation
Removal
E-24
Mounting and Removing the Lens Cap
Fit the lens cap onto the lens
ring as shown in the figure. Be
sure to remove the lens cap
before shooting.
Perform the final checks.
Visual Inspection
After closing the case tightly, check the seal between the front and
rear lids and the connection between the port and case to make sure
the O-rings are not twisted, that they sit properly in the grooves, and
that no foreign matter has been caught between the two parts.
:
•
Hairs, fibers, and other narrow items are not very apparent,
but they may cause entry of water, so that special attention
is required.
Setting the camera power to ON and OFF
Move the power switch button and confirm that the camera can be
turned ON and OFF.
Try to move the mode dial.
After sealing, turn the mode dial knob and confirm that the mode
dial of the camera is switched.
:
•
After inserting the camera into the case, confirm that the
mode dial moves. If it does not move, oil or grease may
have gotten on the mode dial. Wipe it clean.
E-25
Final Test
The final test after loading the camera is explained below. This is the only way to
eliminate worry about possible entry of water! Always perform this test. It can be
performed easily in a water tank or a bathtub. The required time is about five minutes.
Simple water
immersion test
Explanatory
image
Hints
As the Case is transparent,
waterdrops entering into it can be
confirmed easily.
Place the Case
slowly into the water.
1
2
3
4
5
6
7
8
In case of trouble with the O-ring,
three seconds are enough for water
to enter. Are there air bubbles
coming out between the lids?
Please check carefully.
At first, immerse the
Case for only three
seconds.
Remove the Case from the water and
check that no water has accumulated at
the bottom of the Case.
Check that no water
has entered into the
Case.
Is there any water trickling down?
Next, immerse the
Case for 30
seconds.
Check carefully for air bubbles!
Do not perform any operation yet,
but just observe.
Remove the Case from the water and
check that no water has accumulated
at the bottom of the Case.
Check that no water
has entered.
Perform very careful confirmation.
Check carefully for air bubbles!
Try operation of the buttons used frequently.
Check carefully for air bubbles!
If there is still no entry of water,
everything is OK!
Next, check by
immersing for three
minutes.
This is very important!
This is the final check.
Has the silica gel
become moist?
Has the silica gel become moist?
Please check carefully!
As the inside can be seen, the inspection for
entry of water also can be made securely!
Now everything is
all right.
Do not forget the
balance weight.
Now everything is all right!
Have a nice dive!
Did you remember to attach the
balance weight?
E-26
4. Taking Pictures Under Water
How to Use the Hand Strap
Pass your hand through the
accessory hand strap and
adjust the length with the
stop button.
Take pictures carefully.
Confirm the picture on the LCD monitor.
This Case uses the LCD monitor to confirm the picture. The
viewfinder cannot be used.
Quietly press the shutter lever.
When pressing the shutter lever, hold the Case securely with both
hands and operate the lever quietly to prevent camera shake.
Caution when using the flash
When taking macro shots with a wide-angle setting, the flash may
provide uneven and/or insufficient illumination.
Wide angle : Approx. 0.8 m to 5.8 m
Flash reaching range
(Land shooting)
Tele :
Approx. 0.2 m to 4.0 m
During underwater shooting, shooting conditions (water clarity,
suspended matter, etc.) can have a significant effect on the range
of the flash.
Always check your pictures on the LCD monitor after shooting.
:
• When the Wide Port for PT-023 (optional PPO-05) is
used, the light from the camera's built-in flash will not
be sufficient for shooting. In this case, use an external
flash (for example, the FL-20 Electronic Flash and
PFL-01 case).
E-27
5. Handling After Shooting
Wipe off any waterdrop.
After underwater shooting,
remove any drops of water from
the case. Use pressurized air or
a soft, lint-free cloth to carefully
wipe away any moisture from the
hinge between the front and rear
lids, the shutter release lever, the
handgrip and the buckles.
:
• Water left between the front and rear lids or between
the case and port can get inside the case once it is
opened or the port is detached. Please dry these
areas carefully.
• When opening the case or removing the port, make
sure no water from outside (e.g. drops from your hair
or the diving suit) gets inside of the case and/or on
the camera!
• Before opening the case or removing the port, ensure
that your hands or gloves are completely clean (free
of sand, loose fibers, etc.).
• Never open the case or remove the port in areas
where water could splash or spray or where sand or
dust could be blown in the air. When this cannot be
avoided, for example if the battery or memory card
needs to be changed, the case and camera should be
protected from the wind or spray with a plastic sheet
or similar object.)
• Never touch the digital camera and/or battery you're
your hands are wet with sea water.
Note:
• Moisten a cloth or towel with tap water and keep it in
a plastic bag. Use this to wipe the salt water or
crystals from your hands before you touch the
camera.
E-28
Take out the digital camera.
Open the case carefully, pull up the mode dial from the upper surface of
the case to disengage it from the mode lever of the camera, and then
remove the digital camera from the case.
:
• After opening the case, always put it down it with the
O-ring side face-up. Otherwise, dirt or other foreign
matter could attach itself to the O-rings and/or the
contact surfaces, allowing water to penetrate the case
during the next dive.
• For information on storing images, refer to the digital
camera's instruction manual.
• When removing the digital camera from the case, it is
very important you make sure the case’s mode dial
knob is not still attached to the camera’s mode dial.
Never use force to remove the digital camera. This
could damage the camera or the case.
E-29
Wash the Case with pure water.
After use, seal the Case again after taking out the camera and wash it
sufficiently in pure water as soon as possible. After use in sea water,
it is effective to immerse it for a fixed time in pure water to remove
any salt.
:
• Water leakage may be caused when a high water
pressure is applied locally. Before washing the Case
with water, remove the digital camera from it.
• Operate the shutter lever and various buttons of this
product in pure water to remove salt adhering to the
shaft. Do not disassemble for cleaning.
• Drying the Case with adhering salt may impair the
function. Always wash off any salt after use.
Dry the Case.
After washing with pure water, use a soft cloth without any salt on it
and not causing any fibers to wipe off any waterdrop and dry the
Case completely at a well ventilated location in the shade.
In particular, to prevent the threaded sections of the TTL cable and
TTL cable connector from sticking, be sure to clean the threaded
sections with a cotton swab and apply a thin, uniform layer of O-ring
silicon grease (provided with this case).
:
• Do not use hot air from a hair drier or the like for
drying and do not expose the Case to direct sunlight,
as this may accelerate deterioration and deformation
of the Case and deterioration of the O-ring, leading to
leakage of water.
When wiping the Case, take care not to cause
scratches.
E-30
6. Maintaining the Waterproof Function
Remove the O-ring.
Open the Case and remove the O-ring from the Case.
Removal of the O-ring
ᕃ Insert the O-ring removal pick between the O-ring and the wall of
the O-ring groove.
ᕄ Move the tip of the inserted pick under the O-ring. (Take care not
to damage the O-ring groove with the tip of the pick.)
ᕅ Hold the O-ring with your fingertips after it has come out of the
groove and remove it from the Case.
Remove any sand, dirt, etc.
After visually checking that dirt has been removed from the O-ring,
checking for attached sand and other foreign matter, as well as for
damage and cracks can be done by squeezing the entire circumference
of the O-ring lightly with your fingertips.
Using a clean cloth free of fibers, dirt, etc., a piece of lint-free tissue
paper or a soft toothbrush, remove any foreign matter attached to the
grooves of the O-rings. Also remove sand and dirt particles attached to
the O-ring contact surfaces on the case.
E-31
:
• When a mechanical pencil or a similar other sharp
object is used to remove the O-ring or to clean the
inside of the O-ring groove, the Case and the O-ring
may be damaged and water leakage may be caused.
• When the O-ring is checked with the fingertips, take
care not to stretch the O-ring.
• Never use alcohol, thinner, benzene or similar solvents
or chemicals detergents to clean the O-ring. When such
chemicals are used, it is likely that the O-ring will be
damaged or that its deterioration will be accelerated.
Install the O-ring.
Confirm that no foreign matter is attached, apply a thin coat of the
accessory grease to the O-ring, and fit the O-ring into the groove. At
this time, confirm that the O-ring does not stick out from the groove.
How to Apply Grease to the O-ring
Apply the
exclusive
lubricant to each
O-ring.
Make sure that your fingers and the O-
ring are free of dirt, and squeeze about
5 mm of lubricant onto a finger. (5 mm
is the most appropriate amount.)
1
2
3
4
Surround the lubricant with three
fingers and spread it over the ring. Be
careful not to use excessive force as
this may stretch the O-ring.
Spread the
lubricant all over
the O-ring.
After spreading the lubricant, check
visually and by touch that the O-ring is not
scratched and that its surface is flat. If it is
damaged in any way, replace it with a
brand-new O-ring.
Check that the
O-ring is free of
scratch or
unevenness.
Apply lubricant on
the O-ring contact
surface.
Use the lubricant remaining on the
fingers to clean and lubricate the
case's contact surface.
E-32
:
• Always perform maintenance of the waterproof
function even when the Case has been opened to
exchange the battery or the image storage during
shooting. Neglecting this maintenance may become
the cause of water leakage.
• When the Case is not to be used for a long time,
remove the O-ring from the groove to prevent
deformation of the O-ring, apply a thin coat of silicone
grease, and store it in a clean plastic bag or the like.
• When drying is done with salt attached, it is likely that
a function impairment will be caused. After use,
always wash off any salt.
Maintenance of the threaded sections on the
TTL cable and TTL cable connector
If the threaded sections used to connect the TTL cable to the TTL cable
connector are not maintained properly, salt and other seawater residue
may adhere the TTL cable and prevent it from being disconnected.
After use in seawater, clean off any salt, sand, or other residue as soon
as possible, then dry the equipment thoroughly. Clean the threaded
sections with a cotton swab and apply a thin, uniform layer of O-ring
silicon grease (provided with this case).
Clean and apply O-ring
silicon grease to these
sections.
Maintenance of the TTL Connector Cap
After removing the TTL connector cap from the waterproof cap, be sure
to clean and grease the O-ring.
Use the waterproof cap maintenance adapter to remove the O-ring unit
from the waterproof cap.
Waterproof cap
Waterproof cap
maintenance adapter
E-33
Insert the adapter by aligning its pin with
the hole on the cap.
1
2
3
Turn the adapter counterclockwise to
remove the O-ring unit.
After removing the O-ring attached to the
O-ring unit, clean the O-ring groove and
apply silicon grease to the O-ring. Then,
re-attach the O-ring to the O-ring unit.
O-ring
❈ Reverse the removal procedure to re-attach the O-ring unit to the
waterproof cap.
Replace consumable products.
ț The O-ring is a consumable product. Independent of the number of
times the Case is used, it is recommended that the O-ring should
be replaced by a new one at least once a year.
ț Deterioration of the O-ring is accelerated by the use conditions and
the storage conditions. Replace the O-ring even before a year has
passed if it shows signs of damage, cracking or loss of elasticity.
Note: • Please use original Olympus products for the silicone O-ring
grease, the silica gel, and the O-ring. These consumable
products also can be purchased at an Olympus service station.
E-34
7. Appendix
Q & A on the use of the PT-023
Q1: Which digital cameras can be used with this case?
A1 : This case is designed exclusively for use with the CAMEDIA C-8080
Wide Zoom.
Q2: What points should be observed when inserting the digital camera into
the case?
A2 : When inserting the digital camera you should pay special attention to the
following points:
(1) Check that the digital camera's battery is fully charged.
This is important because in underwater shooting you can only use the
LCD monitor for framing shots. This uses much more battery power than
the optical viewfinder.
(2) Check the number of remaining images that can fit on the memory card.
Please use a card with as much free storage space as possible so you
won't have open and close the case to replace the card.
(3) Remove the carrying strap and lens cap from the digital camera.
If the carrying strap and lens cap are not removed from the digital
camera, they could catch between the two lids of the case and prevent it
from closing properly. This could lead to water penetration.
(4) Before closing the case, check that the O-rings sit correctly in the
groove.
(5) Make sure that the buckles used for connection of the case and port and
TTL connector cap are closed firmly.
(6) Make sure that the O-rings and the case's contact surfaces are free of
foreign matter and dirt.
(7) Place the silica gel bag in the case to avoid fogging. Only use Olympus
silica gel.
(8) When loading the digital camera into this case, first attach the camera
mount to the camera and make sure that the projecting section of the
camera’s zoom lever fits into the zoom lever notch on the case. Load the
camera carefully, close the rear lid on the case and lock the buckle.
(9) Install the special balance weight on the tripod mount thread.
Q3: What cautions must be observed when using and storing the Case?
A3 : Pay special attention to the following items.
(1) When the O-ring contact surface is pressed strongly from the outside of
the Case, or when the Case is twisted, the waterproof function may be
impaired and water leakage may be caused.
(2) When the Case is used, left or stored at the following locations, defective
operation or trouble may be caused. Always avoid such locations.
E-35
(a) Places where the Case can reach high temperatures under direct
sunlight or in a car, places with extremely low temperatures, and
places with extreme temperature variations
(b) Places with open fire
(c) Places with volatile substances
(d) Places with vibrations
(3) In case of the following handling with a camera loaded into the Case,
trouble or breakage may be caused for the Case and/or the loaded
camera. Always avoid such handling.
(a) Hitting other objects
(b) Dropping
(c) Placing heavy objects on top of the Case
(4) When the Case is not used for a long time, trouble from formation of
mold etc. may be caused. Before use, confirm the operation of all
operation parts and perform the advance test and the final test.
Q4: What cautions must be observed when opening and closing the Case?
A4 : Pay special attention to the following items.
(1) Do not open and close the Case at locations with water spray or sand
spray.
(2) Wipe off all waterdrops from the gap between the front lid and the rear lid
and around projections and recesses such as the buckles. When this is
not done, entry of waterdrops into the Case is to be feared at the time of
opening and closing.
(3) When opening the Case, take care that no water will drip from your hair
or body into the Case or onto the camera.
(4) When the case is open, examine the O-rings and the O-ring contact
surfaces on the front lid for foreign matter such as hair, fiber, and grains
of sand. Remove these if present. Also examine the O-rings used for
connection of the case and port.
(5) Do not touch the camera or the image storage with your hands to which
sea water is sticking.
(6) If you should detect waterdrops or other signs of water leakage while
shooting, immediately end the dive, perform the water leakage test
again, and confirm that there is no leakage. If the camera is wet, wipe off
any moisture and check the operation.
Q5: How should the Case be handled after use?
A5 : After use, take out the camera as soon as possible and wash the Case
with pure water. In case of use in the ocean, it is effective to immerse the
Case for a certain time in pure water to remove any salt. Operate the
buttons and levers under water to turn the shafts and wash off any salt.
After washing, use a dry cloth without any salt on it to wipe off any
E-36
moisture and dry the Case in the shade. Do not use hot air from a hair
drier or the like and do not dry the Case under direct sunlight. Exposure
to high temperatures or direct sunlight may cause deformation,
discoloration or breakage of the Case and deterioration of the O-ring.
Wipe the inside of the Case with a soft cloth not causing any fibers.
Remove the O-ring, wipe off any salt, sand, dust, etc., and also clean the
O-ring groove and the O-ring contact surface in the same way and then
dry them. When an object with a sharp tip is used to remove the O-ring
from the groove, the O-ring may be damaged and water leakage may be
caused. Always use the accessory pick for O-ring removal.Be sure to
clean the threaded sections on the TTL cable and TTL cable connector
after drying and apply a thin, uniform layer of O-ring silicon grease
(provided with this case).
Q6: How should I take pictures under water?
A6 : Please observe the following items for shooting under water.
(1) Fix the Case with the accessory hand strap to your wrist.
(2) When you place a finger onto the lens window, the finger will appear in
the photo. Pay attention to the position of your fingers when holding the
Case.
(3) When pressing the shutter lever, hold the Case securely with both hands
and operate the lever quietly to prevent camera shake.
(4) Look through the LCD monitor window on the rear of the Case to confirm
the picture and then press the shutter lever. Please note that the
viewfinder cannot be used, When the LCD monitor is used, the battery is
exhausted earlier. In order to avoid losing shutter chances due to an
exhausted battery, please always replace a battery with a fully charged
battery before each dive.
Q7: How can I check for water leakage?
A7 : For confirmation, perform the advance test and the final test after loading
the camera. The advance test with immersing the Case without the
camera to the intended use depth to check for water leakage is the most
accurate test, but when this is difficult, it is safer to perform this test even
at a depth of 1 m or in a bathtub. The final test also can be performed in
a bathtub or a bucket.
Q8: What are the causes for entry of water?
A8 : The main causes for the entry of water are shown below. Please check
them most carefully.
(1) Forgetting to install the O-ring
(2) The O-ring is partly or completely outside the groove.
E-37
(3) Damage, deterioration, or deformation of the O-ring
(4) Sand, fibers, hair or other foreign matter on the O-ring
(5) When foreign matter (sand, fiber, hair, etc.) is stuck to the O-ring
grooves or O-ring contact surfaces.
(6) Catching of the strap, the bag of silica gel, etc. at the time of sealing the
Case.
(7) Throwing the Case from a boat into the water, jumping with the Case into
the water, or other sudden application of strong forces onto the Case.
When entering the water, hand the Case over quietly or avoid impacts in
other ways.
Q9: What are the important points for O-ring maintenance?
A9 : Please observe the following items.
(1) Never use alcohol, thinner, benzene or similar organic solvents or
chemical detergents to clean the O-ring. When such chemicals are used,
it is to be feared that the O-ring will be damaged or that its deterioration
will be accelerated.
(2) Use the original Olympus silicone O-ring grease (white cap). The grease
attached to Cases up to PT-008 (red cap) and the grease of other
companies are not suitable for this silicone O-ring, and use of such
grease may cause deterioration of the surface and impairment of the
waterproof function.
(3) In order to avoid deformation of the O-ring when the Case is not used for
a long time, remove the O-ring from the Case, apply a thin coat of the
special grease, and store the O-ring in a clean plastic bag. For reuse,
confirm that the O-ring is free of damage and cracks, that it has sufficient
elasticity, that the surface is free of stickiness and other abnormalities,
and use it after applying a thin coat of the special grease. Excessive
application of grease does not improve the waterproof function or the
permissible withstand pressure. However, it may facilitate attachment of
sand, dirt, etc.
A thin, uniform coat produces the best result.
(4) The O-ring is a consumable product. Replace it at least once a year.
(5) Deterioration of the O-ring is accelerated by the use conditions and the
storage conditions. Replace the O-ring immediately by a new one if it
shows signs of damage, cracking or loss of elasticity.
Q10
:
What are the important points for Case maintenance?
Please observe the following items.
A10:
(1) Never use the following chemicals for cleaning, corrosion protection,
defogging, repair or other purposes.
•
Never use alcohol, thinner, benzene or similar volatile organic solvents
or chemical detergents to clean the Case. Pure water or lukewarm water
E-38
is sufficient for cleaning.
•
Do not use anticorrosion agents on the metal parts. The metal parts are
made of aluminum, brass or stainless steel. Cleaning with pure water is
sufficient.
•
•
Do not use commercial defogging agents. Always use the original
Olympus defogging silica gel.
Do not use adhesive for repairs or other purposes. When repair is
required, please contact a service station of our company or your dealer.
Q11
:
Please tell me about repairs.
A11:
Please contact a service station of our company or your dealer, if repair
should be necessary. Do not try to repair, disassemble or modify the
Case yourself. Repair, disassembly or modification by you or third
parties not authorized by Olympus invalidates the guarantee.
Q12
:
What are the model numbers of the PT-023 accessories?
The following accessories are being sold.
A12:
(1) O-ring for the PT-023 case (POL-023A/¥1,050 with tax, POL-
023B/¥1,050 with tax, POL-023C/¥1,050 with tax): Silicone rubber
packing for sealing the case. Three types of O-rings are available. O-
rings designed for models other than the PT-023 cannot be used.
(2) O-rings for attaching the PPO-04 standard port to the PT-023 case
(POL-104/¥1,050 with tax): Silicon rubber packing for sealing the
connection between the PPO-04 and PT-023.
(3) Silicone O-ring grease (PSOLG-1/¥840 with tax): This is a special
grease for silicone O-ring maintenance.
(4) Silica gel (SILCA-5/¥525 with tax): This is a desiccant used to prevent
fogging of the glass parts of the Case. The quantity is five bags.
(5) LCD hood (PFUD-04/¥1,050 with tax): This hood is installed on the LCD
monitor window of the Case to make it easier to see the LCD monitor of
the camera.
(6) Balance weight for PT-023 (PWT-023/¥2,625 with tax): This is a weight
intended to bring the Case close to neutral buoyancy in sea water. Under
consideration of the environment, no lead is used.
h You can order in large computer shops and camera mass sale stores.
h Please contact your dealer or a service station of our company when
replacement is required. Replacement will be made against payment.
Q13
:
How can I take good underwater photos?
A13:
Olympus's ZUIKO CLUB online school website has a page describing
underwater shooting techniques. You can access this page at the
following link:
E-39
After-sale Service
● You will receive the Warranty card from your dealer. Please make
sure that the dealer's name, the date of purchase, etc. have been
entered. If they have not been entered, immediately ask your
dealer to have them entered. Read the guarantee conditions
carefully and keep the guarantee card at a safe location.
● Please contact your dealer or one of the service stations of
OLYMPUS CORPORATION listed in this instruction manual for
questions on aftersale service for this product or in case of defects.
In case of a defect of this product, occurring within one year after
the date of purchase and with handling according to this instruction
manual, repair based on the conditions specified in the guarantee
card is performed free of charge.
Payment is required for repairs after expiration of the guarantee
period and for trouble caused by problematic handling by the
customer even during the guarantee period.
● OLYMPUS CORPORATION keeps repair parts for this product for
approximately five years after the end of production of the product.
Accordingly, in principle repairs are accepted during this period. As
repair may be possible even after this period, please contact your
dealer or a service station in your neighborhood.
● Warranty is limited to and valid only in the region of intended
distribution.
● Incidental damages from defects of this product (expenses
required for diving, shooting expenses, loss of profit from photos,
etc.) shall be excluded from the guarantee. In addition, transport
expenses etc. related to repair shall be paid by the customer,
independent of whether they are incurred during or after the
guarantee period.
E-40
Specifications
Available models
Olympus digital camera
CAMEDIA C-8080 Wide Zoom
Pressure
resistance
Depth of up to 40 m
Main body: Transparent polycarbonate
Buckles: Stainless steel
Main materials
Grip/shutter release lever/zoom lever/mode dial
knob/jog dial: Red polycarbonate
Lens window: FL reinforced glass
Lens ring: Aluminum
Buttons: Nickel-plated brass
O-rings/lens cap: Silicone rubber
LCD hood: NBR rubber
Dimensions
Weight
Width 181 mm x height 188 mm x thickness 200 mm
(projections not included)
1,475 g (LCD hood not included)
❈ We reserve the right to change the external appearance and the
specifications without notice.
Diver's Insurance Guide
We recommend to subscribe to diver's insurance for water leakage.
For details, refer to the enclosed Diver's Insurance Guide.
E-41
|