Behringer VP1220F User Manual

User Manual  
EUROLIVE  
VP2520  
Professional 2000-Watt PA Speaker with Dual 15" Woofers and 1.75" Titanium-Diaphragm Compression Driver  
VP1800S  
Professional 1600-Watt 18" PA Subwoofer  
VP1520  
Professional 1000-Watt PA Speaker with 15" Woofer and 1.75" Titanium-Diaphragm Compression Driver  
VP1220F  
Professional 800-Watt Floor Monitor with 12" Woofer and 1.75" Titanium Compression Driver  
VP1220  
Professional 800-Watt PA Speaker with 12" Woofer and  
1.75" Titanium-Diaphragm Compression Driver  
3
EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
9. Do not defeat the safety purpose of the polarized  
UNDERTAKING OR REPRESENTATION. THIS MANUAL  
IS COPYRIGHTED. NO PART OF THIS MANUAL MAY  
BE REPRODUCED OR TRANSMITTED IN ANY FORM  
OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,  
Important Safety  
Instructions  
or grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding-type plug  
has two blades and a third grounding prong. The wide  
blade or the third prong are provided for your safety. If the INCLUDING PHOTOCOPYING AND RECORDING OF ANY  
provided plug does not fit into your outlet, consult an  
electrician for replacement of the obsolete outlet.  
KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS  
WRITTEN PERMISSION OF MUSIC GROUP IP LTD.  
10. Protect the power cord from being walked on or  
pinched particularly at plugs, convenience receptacles,  
and the point where they exit from the apparatus.  
ALL RIGHTS RESERVED.  
© 2012 MUSIC Group IP Ltd.  
Trident Chambers, Wickhams Cay, P.O. Box 146,  
Road Town, Tortola, British Virgin Islands  
Terminals marked with this symbol carry  
electrical current of sufficient magnitude  
to constitute risk of electric shock.  
11. Use only attachments/accessories specified by  
the manufacturer.  
Use only high-quality professional speaker cables with  
¼" TS or twist-locking plugs pre-installed. All other  
installation or modification should be performed only  
by qualified personnel.  
12. Use only with the  
cart, stand, tripod, bracket,  
or table specified by the  
LIMITED WARRANTY  
§ 1 Warranty  
manufacturer, or sold with (1) This limited warranty is valid only if you purchased  
the apparatus. When a cart the product from a MUSIC Group Authorized Reseller in  
This symbol, wherever it appears,  
alerts you to the presence of uninsulated  
dangerous voltage inside the  
is used, use caution when  
the country of purchase. A list of authorized resellers can  
moving the cart/apparatus be found on BEHRINGER’s website behringer.com under  
enclosure - voltage that may be sufficient to constitute a  
risk of shock.  
combination to avoid  
“Where to Buy, or you can contact the MUSIC Group office  
closest to you.  
injury from tip-over.  
This symbol, wherever it appears,  
alerts you to important operating and  
maintenance instructions in the  
13. Unplug this apparatus during lightning storms or  
(2) MUSIC Group* warrants the mechanical and  
when unused for long periods of time.  
electronic components of this product to be free of defects  
in material and workmanship if used under normal  
operating conditions for a period of one (1) year from  
the original date of purchase (see the Limited Warranty  
terms in § 4 below), unless a longer minimum warranty  
period is mandated by applicable local laws. If the product  
shows any defects within the specified warranty period  
and that defect is not excluded under § 4, MUSIC Group  
shall, at its discretion, either replace or repair the product  
using suitable new or reconditioned product or parts.  
In case MUSIC Group decides to replace the entire product,  
this limited warranty shall apply to the replacement  
product for the remaining initial warranty period, i.e.,  
one (1) year (or otherwise applicable minimum warranty  
period) from the date of purchase of the original product.  
14. Refer all servicing to qualified service personnel.  
Servicing is required when the apparatus has been  
damaged in any way, such as power supply cord or plug  
is damaged, liquid has been spilled or objects have fallen  
into the apparatus, the apparatus has been exposed  
to rain or moisture, does not operate normally, or has  
been dropped.  
accompanying literature. Please read the manual.  
Caution  
To reduce the risk of electric shock, do not  
remove the top cover (or the rear section).  
No user serviceable parts inside. Refer servicing to  
qualified personnel.  
Caution  
To reduce the risk of fire or electric shock,  
do not expose this appliance to rain and  
15. The apparatus shall be connected to a MAINS socket  
outlet with a protective earthing connection.  
16. Where the MAINS plug or an appliance coupler is  
used as the disconnect device, the disconnect device shall  
remain readily operable.  
moisture. The apparatus shall not be exposed to dripping  
or splashing liquids and no objects filled with liquids,  
such as vases, shall be placed on the apparatus.  
Caution  
These service instructions are for use  
by qualified service personnel only.  
(3) Upon validation of the warranty claim, the repaired  
or replacement product will be returned to the user  
freight prepaid by MUSIC Group.  
To reduce the risk of electric shock do not perform any  
servicing other than that contained in the operation  
instructions. Repairs have to be performed by qualified  
service personnel.  
(4) Warranty claims other than those indicated above  
are expressly excluded.  
PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF  
OF PURCHASE COVERING YOUR LIMITED WARRANTY.  
THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF  
OF PURCHASE.  
1. Read these instructions.  
2. Keep these instructions.  
3. Heed all warnings.  
LEGAL DISCLAIMER  
TECHNICAL SPECIFICATIONS AND APPEARANCES  
ARE SUBJECT TO CHANGE WITHOUT NOTICE AND  
ACCURACY IS NOT GUARANTEED. BEHRINGER IS  
PART OF THE MUSIC GROUP (MUSIC-GROUP.COM).  
ALL TRADEMARKS ARE THE PROPERTY OF THEIR  
RESPECTIVE OWNERS. MUSIC GROUP ACCEPTS NO  
LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED  
BY ANY PERSON WHO RELIES EITHER WHOLLY OR  
IN PART UPON ANY DESCRIPTION, PHOTOGRAPH  
OR STATEMENT CONTAINED HEREIN. COLORS AND  
SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.  
MUSIC GROUP PRODUCTS ARE SOLD THROUGH  
AUTHORIZED FULLFILLERS AND RESELLERS ONLY.  
FULLFILLERS AND RESELLERS ARE NOT AGENTS OF  
MUSIC GROUP AND HAVE ABSOLUTELY NO AUTHORITY  
TO BIND MUSIC GROUP BY ANY EXPRESS OR IMPLIED  
§ 2 Online registration  
4. Follow all instructions.  
5. Do not use this apparatus near water.  
6. Clean only with dry cloth.  
Please do remember to register your new BEHRINGER  
equipment right after your purchase at behringer.com  
under“Support”and kindly read the terms and conditions  
of our limited warranty carefully. Registering your  
purchase and equipment with us helps us process  
your repair claims quicker and more efficiently.  
Thank you for your cooperation!  
7. Do not block any ventilation openings. Install in  
accordance with the manufacturer’s instructions.  
8. Do not install near any heat sources such as  
radiators, heat registers, stoves, or other apparatus  
(including amplifiers) that produce heat.  
§ 3 Return materials authorization  
(1) To obtain warranty service, please contact the  
retailer from whom the equipment was purchased.  
Should your MUSIC Group Authorized Reseller not be  
located in your vicinity, you may contact the MUSIC Group  
Authorized Fulfiller for your country listed under  
4
EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
“Support”at behringer.com. If your country is not  
listed, please check if your problem can be dealt with  
by our“Online Support”which may also be found under  
“Support”at behringer.com. Alternatively, please submit  
an online warranty claim at behringer.com BEFORE  
returning the product. All inquiries must be accompanied  
by a description of the problem and the serial number  
of the product. After verifying the product’s warranty  
eligibility with the original sales receipt, MUSIC Group  
will then issue a Return Materials Authorization  
(“RMA”) number.  
connection or operation of the unit in any way  
that does not comply with the technical or safety  
regulations applicable in the country where the  
product is used;  
(3) This warranty does not detract from the seller’s  
obligations in regard to any lack of conformity of the  
product and any hidden defect.  
§ 9 Amendment  
damage/defects caused by acts of God/Nature  
(accident, fire, flood, etc) or any other condition that  
is beyond the control of MUSIC Group.  
Warranty service conditions are subject to change without  
notice. For the latest warranty terms and conditions  
and additional information regarding MUSIC Group’s  
limited warranty, please see complete details online at  
behringer.com.  
(7) Any repair or opening of the unit carried out by  
unauthorized personnel (user included) will void the  
limited warranty.  
* MUSIC Group Macao Commercial Offshore Limited of  
Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau,  
including all MUSIC Group companies  
(8) If an inspection of the product by MUSIC Group  
shows that the defect in question is not covered by the  
limited warranty, the inspection costs are payable by  
the customer.  
(2) Subsequently, the product must be returned in  
its original shipping carton, together with the return  
authorization number to the address indicated by  
MUSIC Group.  
(9) Products which do not meet the terms of this  
limited warranty will be repaired exclusively at the buyer’s  
expense. MUSIC Group or its authorized service center will  
inform the buyer of any such circumstance. If the buyer  
fails to submit a written repair order within 6 weeks after  
notification, MUSIC Group will return the unit C.O.D. with  
a separate invoice for freight and packing. Such costs will  
also be invoiced separately when the buyer has sent in a  
written repair order.  
(3) Shipments without freight prepaid will not  
be accepted.  
§ 4 Warranty Exclusions  
(1) This limited warranty does not cover consumable  
parts including, but not limited to, fuses and batteries.  
Where applicable, MUSIC Group warrants the valves or  
meters contained in the product to be free from defects  
in material and workmanship for a period of ninety (90)  
days from date of purchase.  
(10) MUSIC Group Authorized Resellers do not sell new  
products directly in online auctions. Purchases made  
through an online auction are on a“buyer beware”basis.  
Online auction confirmations or sales receipts are not  
accepted for warranty verification and MUSIC Group will  
not repair or replace any product purchased through an  
online auction.  
(2) This limited warranty does not cover the product  
if it has been electronically or mechanically modified  
in any way. If the product needs to be modified or  
adapted in order to comply with applicable technical  
or safety standards on a national or local level, in any  
country which is not the country for which the  
product was originally developed and manufactured,  
this modification/adaptation shall not be considered a  
defect in materials or workmanship. This limited warranty  
does not cover any such modification/adaptation,  
regardless of whether it was carried out properly or not.  
Under the terms of this limited warranty, MUSIC Group  
shall not be held responsible for any cost resulting from  
such a modification/adaptation.  
§ 5 Warranty transferability  
This limited warranty is extended exclusively to the  
original buyer (customer of authorized reseller) and is  
not transferable to anyone who may subsequently  
purchase this product. No other person (reseller, etc.)  
shall be entitled to give any warranty promise on behalf  
of MUSIC Group.  
(3) This limited warranty covers only the product  
hardware. It does not cover technical assistance for  
hardware or software usage and it does not cover  
any software products whether or not contained in  
the product. Any such software is provided“AS IS”  
unless expressly provided for in any enclosed software  
limited warranty.  
§ 6 Claim for damage  
Subject only to the operation of mandatory applicable  
local laws, MUSIC Group shall have no liability to the buyer  
under this warranty for any consequential or indirect  
loss or damage of any kind. In no event shall the liability  
of MUSIC Group under this limited warranty exceed the  
invoiced value of the product.  
(4) This limited warranty is invalid if the  
factory-applied serial number has been altered or  
removed from the product.  
§ 7 Limitation of liability  
This limited warranty is the complete and exclusive  
warranty between you and MUSIC Group. It supersedes  
all other written or oral communications related to this  
product. MUSIC Group provides no other warranties for  
this product.  
(5) Free inspections and maintenance/repair work  
are expressly excluded from this limited warranty,  
in particular, if caused by improper handling of the  
product by the user. This also applies to defects caused  
by normal wear and tear, in particular, of faders,  
crossfaders, potentiometers, keys/buttons, guitar strings,  
illuminants and similar parts.  
§ 8 Other warranty rights and  
national law  
(1) This limited warranty does not exclude or limit the  
buyer’s statutory rights as a consumer in any way.  
(6) Damage/defects caused by the following conditions  
are not covered by this limited warranty:  
(2) The limited warranty regulations mentioned herein  
are applicable unless they constitute an infringement of  
applicable mandatory local laws.  
improper handling, neglect or failure to operate the  
unit in compliance with the instructions given in  
BEHRINGER user or service manuals;  
5
EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
1. Before You Get Started  
1.1 Shipment  
Your VP series loudspeaker was carefully packed at the assembly plant to assure  
secure transport. Should the condition of the cardboard box suggest that damage  
may have taken place, please inspect the unit immediately and look for physical  
indications of damage.  
!!  
Caution  
Never connect multiple power amps to one loudspeaker. Doing so could cause  
the very fabric of reality to unravel, sending the entire universe into oblivion.  
Worse yet, it could destroy your amplifiers and your loudspeaker.  
5. If using the VP1800S subwoofer, it is important to run the source signal into  
a crossover before the power amp(s). This will allow you to direct only the  
low frequencies to the subwoofer, and the rest of the sound spectrum to the  
full-range loudspeakers.  
Damaged equipment should NEVER be sent directly to us. Please inform  
the dealer from whom you acquired the unit immediately as well  
as the transportation company from which you took delivery.  
Otherwise, all claims for replacement/repair may be rendered invalid.  
6. Turn the sound source on (mixer, stereo, etc.).  
Please always use the original packaging to avoid damage due to  
storage or shipping.  
7. Make sure the volume/gain control on the power amp is turned all the  
way down, and then turn the power on.  
Never let unsupervised children play with the loudspeaker or  
with its packaging.  
8. Activate the sound source, whether it is playing music from a CD player or  
speaking into a microphone, and adjust the levels. Gradually raise the power  
amp volume level to desirable level. If distortion occurs, turn the power  
amp volume down. Should the problem persist, make sure distortion is not  
occurring at the sound source. If you reach the desired volume level by barely  
turning up the power amp level/gain, turn the sound source output down to  
allow the power amp to push the speakers more.  
Please dispose of all packaging materials in an environmentally  
friendly fashion.  
1.2 Online registration  
Please register your new BEHRINGER equipment right after your purchase  
warranty carefully.  
9. Rock ‘n Roll!  
Should your BEHRINGER product malfunction, it is our intention to have it  
repaired as quickly as possible. To arrange for warranty service, please contact  
the BEHRINGER retailer from whom the equipment was purchased. Should your  
BEHRINGER dealer not be located in your vicinity, you may directly contact  
one of our subsidiaries. Corresponding contact information is included in the  
original equipment packaging (Global Contact Information/European Contact  
Information). Should your country not be listed, please contact the distributor  
nearest you. A list of distributors can be found in the support area of our  
website (http://behringer.com).  
2. Connections  
(2)  
(1)  
Fig. 2.1: Connector panel  
Registering your purchase and equipment with us helps us process your  
repair claims more quickly and efficiently.  
(1) The VP series features two locking professional loudspeaker (1) connectors  
that are wired in parallel. You can connect one of the connectors to the  
output on your power amp and tap into the signal from the amp on  
the second connector, in order, for example, to feed this signal into an  
additional loudspeaker. The pin designation of the loudspeaker connector  
is pins 1+ and 1-. Pins 2+ and 2- are not connected.  
Thank you for your cooperation!  
1.3 Basic operation  
Using the VP series loudspeakers is easy and intuitive. Simply follow these steps  
to achieve the best possible sound:  
1. Plug the line-level outputs from a sound source such as a mixer or stereo  
system into a power amp of appropriate size (see 4.2 Power amp rating).  
Make sure the sound source and amplifier are turned off.  
Professional speaker connector  
(compatible with Neutrik Speakon connectors)  
2. Using ¼" TS or professional locking-style speaker cables, plug the power  
amp output into the ¼" or locking-style input on the back of the speaker.  
DO NOT use instrument cables (i.e., guitar cords) for this connection!  
3. If using a pair of VP loudspeakers, run the amp in stereo operation.  
If using just one loudspeaker, mono operation is preferable.  
front view  
rear view  
4. If using four or more loudspeakers, there are a few ways to make the  
connections. The first is to use two power amps, one for each pair of  
loudspeakers. Another is to connect the first pair of loudspeakers in normal  
stereo operation, then use the output jacks on the back of the loudspeakers to  
link the second pair of loudspeakers. This way each channel on the power amp  
is driving two loudspeakers. Make sure that the wattage and ohm rating are  
appropriate for this situation.  
Fig. 2.2: Professional loudspeaker connector  
ATTENTION: Never connect the output signals of different power  
amps to both parallel inputs at the same time. This may permanently  
damage your equipment.  
6
EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
(2) The VP series includes two parallel ¼" TS loudspeaker (2) inputs. You can  
connect one of the connectors to the output on your power amp and tap  
into the signal from the amp on the second connector, in order, for example,  
to feed this signal into an additional loudspeaker.  
Avoid placing full-range loudspeakers in a corner or right next to a wall.  
This enhances the low frequencies and can cause the sound to get muddy.  
Subwoofers may be placed almost anywhere since low frequencies are not  
highly directional  
Make sure that the loudspeakers are not in a place where they could  
be knocked over by dancing audience members, overly eccentric stage  
performers, sudden earthquakes, etc.  
Some rooms, such as gymnasiums and auditoriums, create a large amount  
of natural reverb, making it difficult to maintain intelligible sound.  
Laying carpet or rugs on the ground and curtains across windows or brick  
walls will help dampen the reflections and improve the overall sound  
3.2 How to prevent feedback  
Always place the “front of house” speakers ahead of the microphones  
(from the audience’s perspective), and never behind. Use professional floor  
monitors or an in-ear monitoring system to allow the stage performers to hear.  
3.3 How to avoid feedback when working with  
record players (DJ Applications)  
Fig. 2.3: ¼" TS loudspeaker connector  
When several loudspeakers are wired in parallel the overall impedance In applications with record players, bass feedback can occur. Bass feedback  
Z
T
to be handled by the power amp can be calculated, as shown below,  
occurs when low frequencies get back to the pickup and are reproduced on the  
loudspeakers. The most common causes for this are: speakers located too closely  
to the record player, a room with a wooden floor, or presence of a podium or a  
platform. In such cases, it is best to move the loudspeakers away from the record  
player and remove them from the stage, so that they are located on firm ground.  
Another option is to use raised stands, which prevent the loudspeakers from  
having a direct contact with the ground.  
from the individual impedance values of the connected speakers:  
1
=
ZT  
+
+
1Z 1Z  
....  
1
2
3.4 Loudspeaker protection by using a  
low-cut filter  
For the VP series, here are typical connection scenarios:  
Two 8 Ohm speakers in parallel = 4 Ohms  
Four 8 Ohm speakers in parallel = 2 Ohms  
Two 4 Ohm speakers in parallel = 2 Ohms  
Four 4 Ohm speakers in parallel = 1 Ohm  
Try to prevent damage to your loudspeakers caused by extreme oscillation  
of the low-frequency driver due to subsonic noise and extremely deep  
frequencies. Use an equalizer to cut off those frequencies that fall below  
your loudspeakers’ frequency range, or use a low-cut/high-pass filter.  
Most equalizers and sound-improvement systems offer a low-cut function,  
like the BEHRINGER ULTRAGRAPH DIGITAL DEQ1024, for example. Using a low-cut  
filter in your signal path is particularly recommended if you use record players  
or CD players as your signal source. CD players often produce extremely deep  
frequencies, which can lead to extreme excursions of the low-frequency driver.  
Your amplifier may be damaged if the actual impedance drops below  
its input impedance. Please make sure that the calculated total  
impedance ZT is not smaller than the minimum impedance specified  
for your amplifier.  
4. Additional Considerations  
3. Optimal Operation  
We have developed the VP series for use in a wide range of possible applications. 4.1 Length and diameter of loudspeaker cables  
Of course, the sound of your loudspeakers depends on the acoustic characteristics  
Loudspeaker cables whose diameter is too small can considerably limit the  
of the room/space in which they are being used. The following chapters of  
power amp performance. The longer the cable, the more pronounced the  
this manual will give you information about getting the most out of your  
problem. As a result, musicians often simply “turn up” the amp, which can lead  
EUROLIVE loudspeakers.  
to loudspeaker damage. Therefore, don’t use cables longer than 15 m (45 ft.).  
For most applications, this will not be necessary. Cable diameter should be at  
least 14 - 12 gauge.  
3.1 Loudspeaker placement  
Here are some tips to get optimal sound and performance  
from your loudspeaker(s):  
4.2 Power amp rating  
Elevate the loudspeaker at or above head level. High frequencies are  
the segment of the audio spectrum responsible for clarity and speech  
intelligibility. They can get muffled by the front row of the audience, so we  
Selecting the right amp can turn out to be rather difficult. Therefore, stick to  
the following rule of thumb: the power rating of your amp should be roughly  
twice the loudspeaker load capacity. A loudspeaker rated at 200 Watts  
recommend positioning your loudspeakers so the high-frequency drivers are continuous performance can easily be powered by an amp rated at 400 Watts  
slightly above the height of the audience. The more you can get everyone in  
direct earshot, the better. Imagine the loudspeaker is a giant flashlight,  
and you want to illuminate everyone in the room  
output power. An optimal addition to your speaker system would be the  
BEHRINGER EUROPOWER EP2000 power amp, for example.  
7
EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
4.3 Fuses  
We do not recommend the use of fuses with loudspeaker applications. Damage to  
loudspeakers can be the result of high peak signals and high output power.  
However, fuses can only offer protection from one of these two factors, and never  
from both. Additionally, fuse resistances are sometimes nonlinear, leading to  
distortion and unpredictable overdriving.  
4.4 Protecting your equipment  
Always try to find the optimal signal level. Avoid overdriving your amp  
Keep in mind the physical limitations of your PA system  
Use a limiter to restrict the output signal level. Place the limiter between  
the mixing console and the power amp. For this purpose, our proven  
AUT O-XL MDX1600, COMPOSER PRO-XL MDX2600 and MULTICOM PRO-XL  
MDX4600 compressors offer an outstanding solution. All models can be used  
as a limiter: the audio signal doesn’t overdrive any more, and unpleasant  
“peaks” are effectively avoided  
Our ULTRADRIVE PRO DCX2496 and SUPER-X CX3400/CX2310 crossovers  
are particularly well-suited for protecting your equipment: for each  
output, they have independent limiters.  
5. Application Examples  
Fig. 5.2: Full-range stereo operation with floor monitors  
5.1 Full-range stereo operation  
This example applies to the VP1220, VP1220F, VP1520, and VP2520.  
5.3 Two-way stereo operation with a crossover,  
full-range loudspeakers and subwoofers  
In this example, the main output signal of a mixing console is connected  
to a power amplifier. Both the outputs and inputs are stereo. A full-range  
VP series loudspeaker is connected to each of the amplifier outputs, and these  
loudspeakers reproduce the entire frequency range.  
This example applies to the VP1800S in combination with the full-range  
loudspeakers (VP1220, VP1520, and VP2520).  
Using an external active crossover, the main output signal of a mixing console is  
split into two signals. One signal covers the lower frequency range and the other  
signal covers the mid and high frequency range. The recommended crossover  
frequency is 150 Hz. Then, the mid-high frequency signal is connected to a stereo  
power amplifier. A VP series loudspeaker is connected to each of the amplifier  
outputs. The low-frequency signal is connected to an additional power amplifier,  
which powers two VP1800S subwoofers.  
Fig. 5.1: Full-range stereo operation  
5.2 Full-range stereo operation  
with floor monitors  
This example applies to the VP1220, VP1220F, VP1520, and VP2520.  
This example is a variation of the example above, with the addition of several  
VP1220F floor monitors. Two separate monitor outputs from the mixing  
console are connected to the inputs of a stereo power amplifier. A VP1220F is  
connected to each amplifier output, and a second VP1220F is connected to the  
parallel outputs of the first set of VP1220F monitors.  
Fig. 5.3: Two-way stereo operation with subwoofers  
8
EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
6. Specifications  
VP2520  
VP1800S  
System Data  
System Data  
Continuous Power (IEC 60268-5) 500 W  
Continuous Power (IEC 60268-5) 400 W  
Peak Power  
2000 W  
Peak Power  
1600 W  
Type  
2 ½-way full-range loudspeaker  
40 Hz – 20 kHz  
Type  
Subwoofer  
Frequency Response  
Impedance  
Frequency Response  
Impedance  
35 Hz – 250 Hz  
4 Ohms  
8 Ohms  
Sound Pressure Level (SPL)  
Dispersion  
96 dB (Full space, 1 W @ 1 m)  
70° x 50°  
Sound Pressure Level (SPL)  
Dispersion  
100 dB (Half space, 1 W @ 1 m)  
n/a  
Crossover Frequency  
Rigging Fittings  
2.2 kHz  
Crossover Frequency  
Rigging Fitting  
LP 150 Hz  
ergonomically shaped handle  
ergonomically shaped handle;  
35 mm pole socket  
Components  
Components  
HF Driver  
1.75" titanium-diaphragm  
compression driver  
HF Driver  
LF Driver  
LF Driver  
2 x 15" / 385 mm  
18" / 460 mm  
Dimensions/Weight  
Dimensions/Weight  
Width  
Height  
Depth  
Weight  
18.7" / 475 mm  
41.9" / 1065 mm  
20.1" / 510 mm  
87.7 lbs / 39.8 kg  
Width  
Height  
Depth  
Weight  
20.9" / 530 mm  
25.6" / 650 mm  
24.2" / 615 mm  
91.3 lbs / 41.4 kg  
9
EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
VP1520  
VP1220F  
System Data  
System Data  
Continuous Power (IEC 60268-5) 250 W  
Continuous Power (IEC 60268-5) 200 W  
Peak Power  
1000 W  
Peak Power  
800 W  
Type  
2-way full-range loudspeaker  
45 Hz - 20 kHz  
8 Ohms  
Type  
2-way full-range loudspeaker  
55 Hz - 20 kHz  
Frequency Response  
Impedance  
Frequency Response  
Impedance  
8 Ohms  
Sound Pressure Level (SPL)  
Dispersion  
94 dB (Full space, 1 W @ 1 m)  
70° x 50°  
Sound Pressure Level (SPL)  
Dispersion  
93 dB (Full space, 1 W @ 1 m)  
70° x 50°  
Crossover Frequency  
Rigging Fittings  
2.5 kHz  
Crossover Frequency  
Rigging Fittings  
2.5 kHz  
ergonomically shaped handle;  
integral tripod/stand adapter  
ergonomically shaped handle  
Components  
Components  
HF Driver  
1.75" titanium-diaphragm  
compression driver  
HF Driver  
1.75" titanium-diaphragm  
compression driver  
LF Driver  
12" / 307 mm  
LF Driver  
15" / 385 mm  
Dimensions/Weight  
Dimensions/Weight  
Width  
Height  
Depth  
Weight  
17.3" / 440 mm  
16.9" / 430 mm  
22.6" / 575 mm  
35.7 lbs / 16.2 kg  
Width  
Height  
Depth  
Weight  
17.9" / 455 mm  
27.0" / 685 mm  
18.3" / 465 mm  
49.8 lbs / 22.6 kg  
10 EUROLIVE VP2520/VP1800S/VP1520/VP1220F/VP1220 User Manual  
VP1220  
System Data  
Continuous Power (IEC 60268-5) 200 W  
Peak Power  
800 W  
Type  
2-way full-range loudspeaker  
50 Hz - 20 kHz  
8 Ohms  
Frequency Response  
Impedance  
Sound Pressure Level (SPL)  
Dispersion  
93 dB (Full space, 1 W @ 1 m)  
70° x 50°  
Crossover Frequency  
Rigging Fittings  
2.5 kHz  
ergonomically shaped handle;  
integral tripod/stand adapter  
Components  
HF Driver  
1.75" titanium-diaphragm  
compression driver  
LF Driver  
12" / 307 mm  
Dimensions/Weight  
Width  
Height  
Depth  
Weight  
14.6" / 370 mm  
23.6" / 600 mm  
16.9" / 430 mm  
39.5 lbs / 17.9 kg  
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,  
modifications may be made from time to time to existing productswithout prior notice. Specifications and  
appearance may differ from those listed or illustrated.  
We Hear You  

Blaupunkt Mnchen RDM 169 User Manual
Bogen Communications Car Amplifier ESYS1 (M) User Manual
BT ULTIMATE 106 User Manual
Casio Calculator FX 570W User Manual
Citizen Calculator CT 600J User Manual
FujiFilm Camera Lens D60X12 5R3DE ZP1 User Manual
Hitachi VM E565LA User Manual
Honeywell 88013 User Manual
Honeywell Camcorder HB70 SERIES User Manual
JVC Car Stereo System KD R33 User Manual