MODELꢀW1821ꢀ
ROUTERꢀTABLEꢀ
ATTACHMENT
OWNER'SꢀMANUAL
(FOR MODELS MANUFACTURED SINCE 3/10)
Phone:ꢀ(360)ꢀ734-3482ꢀ•ꢀOnlineꢀTechnicalꢀSupport:ꢀ[email protected]
COPYRIGHTꢀ©ꢀJULY,ꢀ2010ꢀBYꢀWOODSTOCKꢀINTERNATIONAL,ꢀINC.
WARNING:ꢀNOꢀPORTIONꢀOFꢀTHISꢀMANUALꢀMAYꢀBEꢀREPRODUCEDꢀINꢀANYꢀSHAPEꢀORꢀFORMꢀWITHOUT
THEꢀWRITTENꢀAPPROVALꢀOFꢀWOODSTOCKꢀINTERNATIONAL,ꢀINC.
#12866TS
PrintedꢀinꢀChina
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
INTRODUCTION
ACCESSORIES
Woodstock Technical Support ..................2
Specifications.....................................2
Router Table Attachment Accessories....... 19
MAINTENANCE
SAFETY
General .......................................... 20
Cleaning & Protecting ......................... 20
Standard Machinery Safety .....................3
Additional Safety for Router Tables ...........5
PARTS
SETUP
Table ............................................. 21
Fence............................................. 22
Unpacking .........................................6
Inventory ..........................................6
Assembly...........................................7
Router Installation ............................. 11
WARRANTY ........................................ 25
OPERATIONS
General .......................................... 12
Operation Overview ........................... 13
Workpiece Inspection.......................... 13
Edge Jointing ................................... 14
Groove Cutting ................................. 15
Routing Small Stock............................ 16
Free-Hand Routing ............................. 17
USE THE QUICK GUIDE PAGE LABELS TO SEARCH OUT INFORMATION FAST!
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
INTRODUCTION
Woodstock Technical Support
The Model W1821 has been specially designed to provide many years of trouble-free service. Close atten-
tion to detail, ruggedly built parts and a rigid quality control program assure safe and reliable operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent with this manual is to
include the basic information for safety, setup, operation, maintenance, and service of this product.
We stand behind our machines! In the event that questions arise about your machine, please contact
Woodstock International Technical Support at (360) 734-3482 or send e-mail to: tech-support@shopfox.
biz. Our knowledgeable staff will help you troubleshoot problems and process warranty claims.
If you have comments about this manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation Manager
P.O. Box 2309
Bellingham, WA 98227
Email: [email protected]
The Model W1821 Router Table Attachment mounts to most table saws that have 27" deep tables. This
addition to your table saw features a universal router mount, a 20" by 27" precision-ground cast iron
table, an extruded aluminum fence, and a starting pin for contour shaping. Included with the W1821 are
double-cross 3⁄4" x 3⁄8" T-slots, an adjustable support leg, and a 21⁄2" dust port.
Specifications
Table Size .............................................. 20" x 27"
Table T-Slot Size ......................................3⁄4" x 3⁄8
"
"
Fence Board Size (x 2).......................... 121⁄2" x 23⁄4
Number of Table Inserts .......................................2
Table Insert Inside Openings ......................... 1", 23⁄8
"
Table Opening Size ............................................4"
Router Base Thickness Range ....................... 1⁄4"–21⁄4
Dust Port Size............................................... 21⁄2
"
"
Fits the following Shop Fox Model table saws: W1677, W1703, W1711, W1714, W1725, W1726, W1748,
W1817, W1818, W1819, W1820 (may fit additional models as they are released).
NOTICE
The Model W1821 mounts on most table saws that have 27" deep tables. If your table saw does
not have mounting holes for the installation of the router table, you will need to drill and tap
these holes. Read the entire assembly section before you begin the installation procedure to
make sure the W1821 will fit your table saw.
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Standard
SAFETY
SAFETY
Machinery Safety
READ MANUAL BEFORE OPERATING MACHINE.
FAILURE TO FOLLOW INSTRUCTIONS BELOW WILL
RESULT IN PERSONAL INJURY.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury.
This symbol is used to alert the user to useful information about proper
operation of the equipment, and/or a situation that may cause damage
to the machinery.
NOTICE
Standard Safety Instructions
1. READ THROUGH THE ENTIRE MANUAL BEFORE STARTING MACHINERY. Machinery presents serious
injury hazards to untrained users.
2. ALWAYS USE ANSI APPROVED SAFETY GLASSES WHEN OPERATING MACHINERY. Everyday eye-
glasses only have impact resistant lenses—they are NOT safety glasses.
3. ALWAYS WEAR A NIOSH APPROVED RESPIRATOR WHEN OPERATING MACHINERY THAT PRODUCES
DUST. Wood dust is a carcinogen and can cause cancer and severe respiratory illnesses.
4. ALWAYS USE HEARING PROTECTION WHEN OPERATING MACHINERY. Machinery noise can cause
permanent hearing damage.
5. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, or jewelry which may
get caught in moving parts. Wear protective hair covering to contain long hair and wear non-slip
footwear.
6. NEVER OPERATE MACHINERY WHEN TIRED, OR UNDER THE INFLUENCE OF DRUGS OR ALCOHOL.
Be mentally alert at all times when running machinery.
7. ONLY ALLOW TRAINED AND PROPERLY SUPERVISED PERSONNEL TO OPERATE MACHINERY. Make
sure operation instructions are safe and clearly understood.
8. KEEP CHILDREN AND VISITORS AWAY. Keep all children and visitors a safe distance from the work
area.
9. MAKE WORKSHOP CHILD PROOF. Use padlocks, master switches, and remove start switch keys.
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
10. NEVER LEAVE WHEN MACHINE IS RUNNING. Turn power OFF and allow all moving parts to come to
a complete stop before leaving machine unattended.
11. DO NOT USE IN DANGEROUS ENVIRONMENTS. DO NOT use machinery in damp, wet locations, or
where any flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL LIT. Clutter and dark shadows may cause accidents.
13. USE A GROUNDED EXTENSION CORD RATED FOR THE MACHINE AMPERAGE. Undersized cords over-
heat and lose power. Replace extension cords if they become damaged. DO NOT use extension cords
for 220V machinery.
14. ALWAYS DISCONNECT FROM POWER SOURCE BEFORE SERVICING MACHINERY. Make sure switch is
in OFF position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE. Keep blades sharp and clean for best and safest performance.
Follow instructions for lubricating and changing accessories.
16. MAKE SURE GUARDS ARE IN PLACE AND WORK CORRECTLY BEFORE USING MACHINERY.
17. REMOVE ADJUSTING KEYS AND WRENCHES. Make a habit of checking for keys and adjusting
wrenches before turning machinery ON.
18. CHECK FOR DAMAGED PARTS BEFORE USING MACHINERY. Check for binding and alignment of
parts, broken parts, part mounting, loose bolts, and any other conditions that may affect machine
operation. Repair or replace damaged parts.
19. USE RECOMMENDED ACCESSORIES. Refer to the instruction manual for recommended accessories.
The use of improper accessories may cause risk of injury.
20. DO NOT FORCE MACHINERY. Work at the speed for which the machine or accessory was designed.
21. SECURE WORKPIECE. Use clamps or a vise to hold the workpiece when practical. A secured
workpiece protects your hands and frees both hands to operate the machine.
22. DO NOT OVERREACH. Keep proper footing and balance at all times.
23. MANY MACHINES WILL EJECT THE WORKPIECE TOWARD THE OPERATOR. Know and avoid condi-
tions that cause the workpiece to "kickback."
24. ALWAYS LOCK MOBILE BASES (IF USED) BEFORE OPERATING MACHINERY.
25. BE AWARE THAT CERTAIN DUST MAY BE HAZARDOUS to the respiratory systems of people and
animals, especially fine dust. Make sure you know the hazards associated with the type of dust you
will be exposed to and always wear a respirator approved for that type of dust.
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Additional Safety for Router Tables
READ and understand this
entire manual AND the
router owner's manual
before using this attach-
ment. Serious personal
injury may occur if safety
and operational informa-
tion is not understood and
followed. DONOTriskyour
safety by not reading!
USE this and other machinery with caution
and respect. Always consider safety first,
as it applies to your individual working
conditions. No list of safety guidelines can
be complete—every shop environment is
different. Failure to follow guidelines could
result in serious personal injury, damage
to equipment or poor work results.
1. AVOIDING AMPUTATION. Never place hands directly over or in front of the cutter. As one hand
approaches the cutter, move it away. Always keep hand at least 6" away from the spinning cutter.
2. SECURING LEVERS AND KNOBS. Never operate the router table without first making sure that all
lock levers and knobs are tight, and that all fence hardware and guide rails are secure. Otherwise,
the workpiece can slip out of alignment during cutting and cause injury from kickback.
3. PREVENTING WORKPIECE DRAW-IN OR KICKBACK. Always feed the workpiece against the rotation
of the cutter. Never force materials past the router. Let the cutter do the work. Excessive force is
likely to result in poor cutting results and will cause kickback conditions that could cause serious
personal injury.
4. APPROPRIATE WORKPIECES. The danger of kickback and injury is increased when the workpiece
has knots, holes, or foreign objects in it. Warped stock should be run through a jointer before you
run it through the router table.
5. BLIND CUTTING. Keep the cutter on the underside of the workpiece when making blind cuts,
which decreases risk of accidental contact with the cutter.
6. TESTING ROTATION. With the machine disconnected from power, rotate the router spindle to test
any new setup to ensure proper cutter clearance before starting the machine.
7. CUTTING SUPPORT. NEVER cut a workpiece without using a fence, jig, or miter. Otherwise, the
workpiece can be grabbed by the cutter and pull your hands into the cutter.
8. WORKPIECE SIZING. NEVER use a workpiece shorter than six inches without special fixtures or jigs.
Otherwise, the workpiece can become trapped between the fence and cutter, which could draw
your hands into the spinning cutter.
9. CUTTER HEIGHT. Keep any unused portion of the cutter below the table surface, or a workpiece
can be grabbed by the cutter causing kickback and serious injury.
10. USING SAFETY GUARDS. To prevent amputation or other injuries, NEVER remove any guards or 10
when machine is operating. Fabricate additional guards or jigs for special circumstances. Use an
overhead guard if the fence is removed.
11. TRIPPING HAZARD. To prevent tripping over the router power cord when operating the table saw,
always disconnect it and safely store it out of the way.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
SETUP
Unpacking
The Model W1821 has been carefully packaged for safe
transportation. If you notice the product has been
damaged during shipping, please contact your authorized
Shop Fox dealer immediately.
A
Inventory
Refer to Figures 1–3 and the listing below to inventory
the contents of the shipping box.
B
If you can't find an item on this list, check the mounting
locations or examine the packaging materials carefully.
Occasionally we pre-install certain components for
shipping purposes.
Figure 1. Shipping inventory items A–B.
If any nonproprietary parts are missing (e.g. a nut or a
washer), we will gladly replace them; or for the sake of
expediency, replacements can be obtained at your local
hardware store.
C
Description
Qty
G
D
A. Router Table................................................1
B. Support Leg.................................................1
C. Fence & Dust Hood........................................1
D. Knurled Fence Handles ...................................2
E. T-Slot Bars ..................................................2
F. Router Guard Bracket Assembly.........................1
G. Fence Board Shim 1.5mm................................1
H. Fence Board Shim 0.7mm................................1
I. Plastic Router Guard......................................1
J. Router Guard Star Knobs .................................2
K. Support Leg Foot Pad Assembly .........................1
L. Table Insert 1" ID ..........................................1
M. Table Insert 23⁄8" ID .......................................1
N. Starting Pin .................................................1
O. Dust Port 21⁄2" .............................................1
P. Button Head Cap Screws M6-1 x 10 ....................4
Q. Flat Washers 6mm.........................................4
R. Mounting Screw Assemblies..............................3
—Cap Screws M8-1.25 x 30 ..............................3
—Lock Washers 8mm......................................3
—Flat Washers 8mm.......................................3
S. Router Hold-Down Assemblies ...........................4
H
E
F
K
I
J
Figure 2. Shipping inventory items C–K.
O
M
N
L
Q
P
S
R
Figure 3. Shipping inventory items L–S.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Assembly
Saw Table
The Model W1821 mounts on most table saws that have
27" deep tables. If your table saw does not have mounting
holes for the installation of the router table, you will
need to drill and tap these holes. Also, you may have to
modify the fence rails to allow access for the router table
T-slots. Read this entire assembly section before you begin
the installation procedure below to make sure the W1821
will fit your table saw before making any modifications.
Mounting Holes
Needed for Assembly
Qty
Another Person..................................................1
Hex Wrench 4mm ...............................................1
Hex Wrench 5mm ...............................................1
Hex Wrench 6mm ...............................................1
Wrench 10mm ...................................................1
Wrench 13mm ...................................................2
Straightedge (at least 24" long) ..............................1
Router Table
Figure 4. Mounting holes in saw and router
To assemble and install your router table attachment,
do these steps:
tables.
1. DISCONNECT THE TABLE SAW FROM POWER!
Foot Pad
2. Decide which of the following mounting options best
suits your needs:
— Remove the existing right wing of the saw table
and use the existing wing mounting holes to attach
the router table.
Support
Leg
— Mount the router table to the right side of the
saw table or the existing right-hand wing. In
these cases, you will probably need to drill and
tap three M8-1.25 holes into the saw table or
wing that match those in the router table (see
Figure 4).
Jam Nut
Figure 5. Foot pad bolt threaded into the
support leg.
Tip: Use the holes in the router table as a template
for marking the mounting hole locations on the saw
table so that the router table top will mount flush
with the top of the saw table.
Support
Leg
3. Thread the foot pad assembly into the bottom of the
support leg, as shown in Figure 5. For now, do not
tighten the jam nut up to the leg so that you can
adjust the height of the leg in a later step.
4. Thread the support leg onto the stud on the bottom
of the router table, as shown in Figure 6.
Figure 6. Support leg threaded into the
router table.
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
5. If you have long fence rails that will extend beyond
the T-slots of the router table, you will have to
modify the top of the rails. This entails making a
cut-out that matches or exceeds the dimensions of
the router table T-slot, as shown in the illustration in
Figure 7.
Router Table T-Slot
Fence Rail
Cut-Out
Also, drill mounting holes through the rails that
match the holes in the side of the router table.
Figure 7. Illustrated example of a fence
modification.
6. With the help of another person to hold the table
and leg assembly, align the mounting holes in
both tables and secure them together with the (3)
M8-1.25 x 30mm cap screws, (3) 8mm lock washers,
and (3) 8mm flat washers, as shown in Figure 8.
— If you have fence rails that extend beyond the
saw table and across the router table, use the
mounting holes you drilled in Step 5 to fasten the
rails to the router table.
x 3
Figure 8. Router table attached to the
table saw.
7. Place the straightedge across the saw table and
router table to make sure that the combined table
surface is flat.
Tape
— If the combined table surface is flat, continue
with Step 8.
— If the outside edge of the router table tilts down,
place strips of masking tape along the bottom
edge of the saw table to shim the router table up
and even with the saw table from side to side (see
Figure 9).
Figure 9. Using tape to shim the router
table up.
— If the outside edge of the router table tilts up,
place strips of masking tape along the top edge
of the saw table to shim the router table down
and even with the saw table from side to side
(see Figure 10).
Tape
Note: After reinstalling the router table, remove all
excess masking tape with a razor blade.
Figure 10. Positioning the tape to shim
the router table down.
-8-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
8. When the saw and router tables are level with each
other, rotate the foot pad assembly so that it sits
firmly on the floor without changing the height of
the router table. Tighten the jam nut of the foot pad
assembly up to the leg bottom to secure the setting.
T-Slot Bars
9. Slide the two T-slot bars into the T-slots of the
router table (see Figure 11).
Note: The router table double-cross T-slots offer
four different orientations for the router fence—
choose the one that best suits your operation.
Figure 11. T-slot bars installed for one of
four orientations.
10. Place the fence assembly over the studs of the T-slot
bars, then secure the fence in place by threading
the knurled handles onto the studs, as shown in
Figure 12.
Knurled Handles
Figure 12. Fence knurled handles
installed.
Note: The two fence board shims provided with your
router table can be placed between the outfeed
fence board (left) and the fence to offset the
outfeed fence board for full edge routing (see the
illustration in Figure 13 and refer to Edge Routing
on Page 15 for additional details).
Fence
With additional shop-made shims, the outfeed fence
board can be offset up to approximately 4mm from
the infeed board. If you require more offset, you
can obtain longer M6-1 flat head screws to secure
the outfeed fence board.
Shims
Outfeed
Fence Board
Figure 13. Shim installation for full edge
routing.
-9-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
DO NOT operate the attached router without an
adequate dust collection system. Follow your router
manufacturer's specifications for the required dust
collection capacity. Failure to use a dust collection
system can result in short and long-term respiratory
illness.
11. Attach the dust port to the back of the fence
assembly with the (4) M6-1 x 10 cap screws and (4)
6mm flat washers, as shown in Figure 14.
Dust Port
Figure 14. Dust port installed.
12. Slide the attached square nut on the guard bracket
into the top fence T-slot, center it with the dust
hood and dust port, then tighten the cap screw to
secure it in place, as shown in Figure 15.
Guard Bracket
Figure 15. Guard bracket attached to the
fence.
Star Knobs
To reduce the risk of hand injury from accidental
contact with the spinning router bit, with the
exception of freehand routing, ALWAYS make sure
the fence and router guard are properly positioned
and secured before connecting the router to power.
13. Attach the plastic router guard to the guard bracket
with the (2) star knob bolts, as shown in Figure 16.
Router
Guard
Figure 16. Router guard installed.
-10-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Router Installation
The Model W1821 will support a router with a base
thickness between 1⁄4" and 21⁄4".
To install a router, do these steps:
1. DISCONNECT THE SAW AND ROUTER FROM POWER!
2. Slide three of the router hold-down assemblies into
the T-slots underneath the router table so that they
allow room for the router base, as shown in Figure
17.
Adjustment
Bolt
Router Clamp
Note: To properly position the hold-down clamp,
balance the tightness of the hold-down knob and the
adjustment bolt so that the clamp will allow room
for the router base in the next step. If necessary,
put the adjustment bolt jam nut on the other side
of the clamp.
Hold-Down
Knob
Figure 17. Router hold-down assembly
controls.
If the router unexpectedly moves or the router bit
contacts the table insert or fence during operation,
serious personal injury could result from flying
debris. ALWAYS make that at least three router
clamps are used and are applied to a flat surface
of the router base before connecting the router to
power.
3. Slide the router base onto the three hold-down
clamps, position them so that they secure the router
bit in the center of the table opening, then tighten
the hold-down knobs and adjustment bolts to secure
the router in place (see Figure 18).
4. Install the remaining hold-down assembly to
make sure the router stays firmly in place during
operation.
NOTICE
To prevent damage to the
router table T-slots, do not
position the clamp adjustment
bolts over the thin edge of the
T-slots.
Figure 18. Router properly installed.
-11-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
OPERATIONS
General
Your router will perform many types of operations that
are beyond the scope of this manual. Many of these
operations can be dangerous or deadly if performed
incorrectly.
The instructions in this section are written with the
understanding that the operator has the necessary
knowledge and skills to operate the router with this
router table attachment. If at any time you are
experiencing difficulties performing any operation,
stop using the machine!
READ and understand this entire instruc-
tion manual before using this machine.
Serious personal injury may occur if
safety and operational information is not
understood and followed. DO NOT risk
your safety by not reading!
If you are an inexperienced operator, we strongly
recommend that you read books or trade articles, or
seek training from an experienced router operator before
performing any unfamiliar operations. Above all, your
safety should come first!
DO NOT investigate problems or adjust-
ments while the router is running.
Wait until the router is turned OFF,
unplugged and all working parts
have come to a complete stop before
proceeding!
Always wear safety glasses when oper-
ating this machine. Failure to comply
may result in serious personal injury.
-12-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Operation Overview Workpiece Inspection
This overview outlines you the basic process that
happens during an operation with the router
table attachment. Familiarize yourself with this
process to better understand the remaining
parts of the Operation section.
Some workpieces are not safe to cut or may
require modification before routing. Before
routing, inspect all workpieces for the following:
•
Material Type: This router is intended
for cutting natural and man-made wood
products, laminate covered wood products,
and some plastics. This machine is NOT
designed to cut metal, glass, stone, tile,
etc.
To complete a typical operation, the operator
does the following:
1. Examines the workpiece to make sure it is
suitable for cutting.
•
Foreign Objects: Nails, staples, dirt,
rocks and other foreign objects are often
embedded in wood. While shaping, these
objects can become dislodged and hit the
operator, cause kickback, or break the bit,
which might then fly apart. Always visually
inspect your workpiece for these items.
If they can't be removed, DO NOT cut the
workpiece.
2. Adjusts the fence boards close to the bit
for maximum workpiece support, and then
secures the fence boards in place.
3. Adjusts the bit height for the desired
cutting profile.
4. Adjusts the fence position to establish the
depth of cut.
•
Large/Loose Knots: Loose knots may
dislodge during a cutting operation. Knots
can cause kickback and machine damage.
Choose workpieces that do not have large/
loose knots or plan ahead to avoid shaping
through them.
5. Wears safety glasses and a respirator, and
locates push sticks if needed.
6. If using a reversible router, verifies that the
direction of spindle rotation is correct, and
then starts the router.
•
Wet or "Green" Stock: Routing wood
with a moisture content over 20% causes
unnecessary wear on the cutters, increases
the risk of kickback, and yields poor
results.
7. Holds the workpiece firmly and flatly
against the fence, and then pushes the
workpiece into the bit at a steady and
controlled rate until the workpiece moves
completely beyond it.
•
Excessive Warping: Workpieces with
excessive cupping, bowing, or twisting are
dangerous to cut because they are unstable
and often unpredictable when being
shaped. DO NOT process workpieces with
these characteristics unless you properly
square up the stock with a jointer and
planer.
Important: The operator is very careful
to keep the workpiece firmly against the
table and fence during the entire cut.
For smaller workpieces or odd-shaped
workpieces, a zero-clearance fence or jig is
used.
8. Stops the router.
•
Minor Warping: Workpieces with slight
cupping can be safely supported if the
cupped side is facing the table or the
fence. A workpiece supported on the bowed
side will rock during a cut and could cause
kickback or severe injury.
-13-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Edge Jointing
Jointing the edge of a board involves using a straight
cutting router bit to remove wood from the face of the
board. The result is a perfectly flat and square edge.
Always feed the workpiece against
the router bit rotation direction, as
illustrated below. Otherwise, the
workpiece could be aggressively pulled
from your hands, drawing them into the
spinning cutter.
To joint the edge of a workpiece, do these steps:
1. DISCONNECT ROUTER FROM POWER!
2. Secure a straight cutting bit into your router
according to the router manufacturer's instructions.
3. Install the smallest table insert into the router table
that still allows the router bit to freely rotate.
4. Raise the bit to a height slightly more than that
of the workpiece, then rotate it by hand until the
cutting flute is perpendicular to the fence boards.
Workpiece
Bit
Rotation
5. Insert and secure shims between the outfeed fence
board and the fence bracket that equal in thickness
the amount of material you want to remove from the
workpiece face (see the illustration in Figure 19).
Feed Direction
Top View
6. Place a straightedge against the outfeed fence
board, then adjust the fence assembly so that
the straightedge is also against the bit flute, as
illustrated in Figure 19.
Infeed
Fence Board
Shim
7. Lock the fence assembly in place, tighten all knobs,
connect the router to power, then perform the cut
(see Figure 20).
Straight
Router Bit
Outfeed
Fence Board
Straightedge
NOTICE
Figure 19. Fence jointer setup (guard
If you are using a mobile base with the table saw, use
one of the options below when moving the saw and
the router table attachment:
removed for clarity).
•
•
•
Attach an extension to the mobile base that
will provide support for the router table leg.
Install a locking caster onto the bottom of the
router table leg.
Adjust the router table leg foot up, move the
unit, then re-adjust the foot to provide proper
support to the router table.
Top View
Shim
Cutting Direction
Figure 20. Edge jointing (guard removed
for clarity).
-14-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Groove Cutting
Groove cutting produces a groove or bead into the face of
the board.
Top View
To cut a groove into the face of the workpiece, do
these steps:
1. DISCONNECT ROUTER FROM POWER!
2. Secure the bit into the router according to the
router manufacturer's instructions.
Depth-of-Cut
3. Install the smallest table insert into the table that
still allows the bit to freely rotate.
Figure 21. Groove cutting setup—top view
(guard removed for clarity).
4. Make sure both fence boards are even with one
another and secured to the fence assembly.
Depth-of-Cut
5. Raise the bit to the desired height, then adjust the
fence assembly so that the fence boards are behind
the bit the same distance as the desired depth-of-
cut (see the illustrations in Figures 21–22).
Side View
Rub Collar
Bit
6. Lock the fence assembly in place, tighten all knobs,
connect the router to power, then perform the cut.
Table
Figure 22. Groove cutting setup—side view
(guard removed for clarity).
-15-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Routing Small Stock
Feeding small stock past the router bit is always
dangerous. If you must route small stock, use a zero-
clearance fence. This will provide greater protection for
the operator, better workpiece support, and reduced tear
out on narrow or fragile stock.
ALWAYSusehold-downsorfeatherboards
and push sticks when shaping small or
narrow stock. These devices keep your
hands away from the spinning cutter
and sufficiently support the stock to
allow a safe and effective cut, reducing
the risk of personal injury.
To make a zero-clearance fence, do these steps:
1. DISCONNECT ROUTER FROM POWER!
2. Remove the fence boards from the fence assembly.
3. Select a piece of straight and smooth stock that is
the same height and thickness as the fence boards
and approximately 24" long.
4. Cut an outline of the spindle and cutter from the
center of the stock selected in Step 3, as illustrated
in Figure 23.
Mounting
Fastener
Zero-Clearance Fence
Note: Make the outline as close as possible to the
cutter and spindle without interfering with rotation.
5. Create countersunk mounting holes in the zero-
clearance fence so that the screws and T-nuts from
the split fence can be used to secure it to the fence
assembly in the same manner.
Table
Cutter
6. Secure the zero-clearance fence to the fence
assembly, check for proper clearance, connect the
router to power, then run a test piece by the cutter
to verify the results.
Figure 23. Example of a zero-clearance
fence.
-16-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Free-Hand Routing
Irregular or freehand routing, as illustrated in Figure 24,
takes a high degree of skill and dexterity and is done
without the protection and aid from the fence and guard.
The most dangerous part of free-hand routing is beginning
the cut, where the cutter first contacts the workpiece.
Often the workpiece will tend to jerk or kickback,
presenting an injury hazard to the operator.
To reduce this tendency, use a starting pin or block (see
Figures 24–25). This will allow you to anchor and slowly
pivot the workpiece into the cutter as the cut is started,
making the operation more stable and safe.
Free-hand or irregular routing greatly
increases the chance that the operator
may lose control of the workpiece,
which could result in serious personal
injury. Therefore, a starting pin or
block and a custom guard or workpiece
holding jig MUST be used.
With the fence assembly removed, you MUST use a router
bit with a rub collar to guide the workpiece through the
cut and limit the depth-of-cut. Also, use a jig or fixture to
hold the workpiece so that your hands can be kept at a
safe distance from the router bit while cutting.
Swing
If you are unfamiliar with free-hand routing or shaping,
get assistance from an experienced woodworker, read
books on routing and shaping, and start with a simple
project.
Starting Pin
Rub
Collar
Workpiece
ALWAYS use an auxiliary jig and extreme care when
free-hand routing that requires removal of the fence.
Routing without the fence and the attached guard
greatly increases the risk of accidental contact with
the spinning cutter, causing serious personal injury.
Feed Direction
Figure 24. Using a starting pin for
freehand routing (custom guard not shown
for clarity).
To free-hand route, do these steps:
1. DISCONNECT ROUTER FROM POWER!
2. Fabricate a jig to use with the workpiece that will
match the finish shape desired, then attach it to the
workpiece (see Figure 25 for an example).
Note: Make sure any fasteners used will not make
contact with the router bit during the cutting
operation. Glue can be used as an alternative.
Figure 25. Example of using a jig with a
starting block.
-17-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Tip: As an alternative to fabricating a custom jig,
use the Shop Fox Model W1500 Right Angle Jig, as
shown in Figure 26.
3. Remove the fence assembly from the table.
4. Fabricate and mount a custom guard over the bit
that safely protects your hands from the spinning
cutter.
5. Insert the starting pin in the best suited hole on
the routing table or clamp a starting block to the
table (see Figure 25 on the previous page for an
example).
Figure 26. Shop Fox Model W1500 Right
6. Install a router bit with a rub collar as directed by
the router manufacturer's instructions, then raise it
to the desired height (see Figure 27).
Angle Jig.
Rub
Collar
7. Connect the router to power and turn it ON.
Template
8. Rest the jig with the workpiece attached against the
starting pin or block, then slowly pivot and feed it
into the bit. After the cut is started, move the jig
against the rub collar and away from the starting pin
or block, as illustrated in Figure 24 on the previous
page.
Workpiece
Figure 27. Using a template and a rub
collar for free-hand routing.
-18-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
ACCESSORIES
Router Table Attachment Accessories
The following Router Table Attachment accessories may be available through your local Woodstock
International Inc. Dealer. If you do not have a dealer in your area, these products are also available
through online dealers. Please call or e-mail Woodstock International Inc. Customer Service to get a
current listing of dealers at: 1-800-840-8420 or at [email protected].
30 Piece Carbide Tipped Router Bit Set
D3726—1⁄4" Shank
D3727—1⁄2" Shank
This 30 piece carbide tipped router bit set includes all of the most
commonly used router bits conveniently labeled and displayed in a
wooden case with see-through, touch-latch doors for easy access.
W1727—Shop Fox 1 HP Dust Collector
Specifications:
•
•
•
•
•
•
•
•
•
•
Motor: 1 HP, 110V/220V, single phase, 9/4.5 amp draw
800 CFM air suction capacity
5.67" of static pressure
One 4" intake hole
9" balanced steel, radial fin impeller
2.1 ft3 bag capacity
Base size w/casters: 153⁄4" x 393⁄4
2.5 micron bag filtration
"
541⁄2" height with bags inflated
59 lbs. approximate shipping weight
D2274—Shop Fox 5 Roller Stand
For greater work stability and support, this 5 Roller Stand features
large diameter, ball bearing rollers mounted on a sturdy adjustable
pedestal base. Stand adjusts in height from 261⁄2" to 44", is all-steel
construction, has 157⁄8" wide ball bearing rollers, and has a 250 lb.
capacity.
-19-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
MAINTENANCE
General
Regular maintenance on your router table attachment
will ensure its optimum performance. Make a habit of
inspecting your machine each time you use it.
Check for the following conditions and repair or
replace when necessary:
•
•
•
•
Loose mounting T-bolts or lock knobs.
Worn router switch.
Worn or damaged router cords and plugs.
Any other condition that could hamper the safe
operation of this router table attachment.
MAKE SURE that your router is unplugged
during all maintenance procedures! If
this warning is ignored, serious per-
sonal injury may occur.
Cleaning & Protecting
Frequently blow-off sawdust with compressed air, then
wipe away the remaining dust with a clean shop rag. This
is especially important for the internal working parts of
the fence assembly and the router. Dust build-up around
the router is a sure way to decrease its life span.
The cast-iron router table can be kept rust-free with reg-
ular applications of products like SLIPIT®. For long term
storage you may want to consider products like Boeshield
T-9™.
-20-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
PARTS
Table
110
102
109
116
111
103
101
115
104
114
115
112
113
105
106
106
107
111
110
108
REF PART #
DESCRIPTION
ROUTER TABLE
TABLE INSERT 1" ID
TABLE INSERT 2-3/8" ID
THREADED STUD M8-1.25 X 40
SUPPORT LEG
HEX NUT M8-1.25
FOOT PAD
REF PART #
DESCRIPTION
101
102
103
104
105
106
107
108
X1821101
109
110
111
112
113
114
115
116
XPCAP13M
XPLW04M
XPW01M
X1821112
X1821113
XPN01M
CAP SCREW M8-1.25 X 30
LOCK WASHER 8MM
FLAT WASHER 8MM
ROUTER HOLD-DOWN
HOLD-DOWN KNOB M6-1
HEX NUT M6-1
X1821102
X1821103
X1821104
X1821105
XPN03M
X1821107
XPB82M
XPB08M
X1821116
HEX BOLT M6-1 X 20
STARTING PIN
HEX BOLT M8-1.25 X 80
-21-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Fence
143
135
134
117
135
119
134
132
130
134
130
119
129
136
120
139
118
137
136
122
142
128
120
133
137
133
136
136
121
139
124
125
136
138
140
126
141
139
124
125
127
140
128
REF PART #
123
DESCRIPTION
138
REF PART #
DESCRIPTION
117
118
119
120
121
122
123
124
125
126
127
128
129
X1821117
X1821118
X1821119
X1821120
X1821121
X1821122
X1821123
X1821124
X1821125
X1821126
X1821127
X1821128
X1821129
DUST PORT 2-1/2"
DUST HOOD
DUST HOOD SIDE COVER
KNURLED HANDLE M8-1.25 X 25
ROUTER GUARD BRACKET
FENCE
PLASTIC ROUTER GUARD
T-SLOT BAR
T-SLOT RING
GUARD STAND-OFF
STAR KNOB BOLT M6-1 X 15
PHENOLIC FENCE BOARD
FENCE BOARD SHIM 0.7MM
130
132
133
134
135
136
137
138
139
140
141
142
143
XPBHS06M
XPBHS11M
XPLW03M
XPW03M
XPCAP25M
X1821136
XPCAP01M
XPFH12M
X1821139
XPFH30M
X1821141
X1821142
X1821143
BUTTON HD CAP SCR M5-.8 X 12
BUTTON HD CAP SCR M6-1 X 10
LOCK WASHER 6MM
FLAT WASHER 6MM
CAP SCREW M6-1 X 12
SQUARE NUT M6-1
CAP SCREW M6-1 X 16
FLAT HD SCR M6-1 X 25
TEFLON FLAT WASHER 8MM
FLAT HD SCR M5-.8 X 8
PVC PAD
FENCE BOARD SHIM 1.5MM
INJURY HAZARD WARNING LABEL
-22-
Download from Www.Somanuals.com. All Manuals Search And Download.
Model W1821 (For Machines Mfg. Since 3/10)
Download from Www.Somanuals.com. All Manuals Search And Download.
Fold along dotted lIne
place
stamp
Here
Woodstock international inc.
p.o. box 2309
bellingham, Wa 98227-2309
Fold along dotted lIne
tape along edges--please do not staple
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
WARRANTY
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects from workmanship
and materials for a period of two years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or
accidents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the Shop Fox
machine or machine part, which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to a Shop Fox factory service center with proof of their purchase
of the product within two years, and provides Woodstock International, Inc. reasonable opportunity to
verify the alleged defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty, then the original
owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may
be implied by law, including any merchantability or fitness, for any particular purpose, are hereby
limited to the duration of this written warranty. We do not warrant that Shop Fox machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality and durability
standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Download from Www.Somanuals.com. All Manuals Search And Download.
High Quality Machines and Tools
Woodstock International, Inc. carries thousands of products designed
to meet the needs of today's woodworkers and metalworkers.
Ask your dealer about these fine products:
Download from Www.Somanuals.com. All Manuals Search And Download.
|