Operator’s Manual
WIDE CUT MOWER
Model Series
933R
(12A-751-190)
933E
(12AE751-190)
(Model 933R Shown)
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may
have similar laws. Federal laws apply on federal lands. A spark arrester muffler is available through your nearest engine autho-
rized service dealer or contact the service department, P.O. Box 368022 Cleveland, Ohio 44136-9722.
WHITE OUTDOOR PRODUCTS COMPANY P.O. BOX 361131 CLEVELAND, OHIO 44136-9722
PRINTED IN U.S.A.
FORM NO. 770-1180B
(1905434) 10/99
Download from Www.Somanuals.com. All Manuals Search And Download.
Section
1
Safety
SPARK ARRESTER WARNING TO RESIDENTS OF CALIFORNIA AND SEVERAL OTHER STATES
Under California law, and under the laws of several other states, you are not permitted to operate an internal
combustion engine using hydrocarbon fuels on any forest covered, brush covered, or grass covered land, or on
land covered with grain, hay, or other flammable agricultural crop, without an engine spark
arrester in continuous effective working order.
The engine on your power equipment, like most outdoor power equipment, is an internal combustion engine that burns gasoline, a
hydrocarbon fuel. Therefore, your power equipment must be equipped with a spark arrester muffler in continuous
effective working order. The spark arrester must be attached to the engine exhaust system in such a manner that flames or heat
from the system will not ignite flammable material. Failure of the owner/operator of the equipment to comply with this regulation is
a misdemeanor under California law, and may also be a violation of other state and/or federal regulations, laws, ordinances, or
codes. Contact your local fire marshal or forest service for specific information about what regulations apply in your area. Contact
your authorized engine dealer for information about obtaining a spark arrester.
IMPORTANT
Safe Operation Practices for Walk-Behind Mowers
This cutting machine is capable of amputating hands and feet and throwing objects. Failure to observe the
following safety instructions could result in serious injury or death.
5. Be sure the area is clear of other
people before mowing. Stop mower
if anyone enters the area. Keep by-
standers at least 25 feet away from
the area of operation.
cleaning the mower or unclogging
the chute.
I. GENERAL OPERATION
1. Read, understand, and follow all in-
structions on the machine and in the
manuals. Be thoroughly familiar with
the controls and the proper use of
the mower before starting.
6. Do not operate the mower when
barefoot or wearing open sandals.
Always wear substantial foot wear.
2. Do not put hands or feet near or
under rotating parts. Keep clear of
the mower blade and discharge
opening at all times.
12. Shut the engine off, wait until the
blade comes to a complete stop, and
disconnect the spark plug wire be-
fore installing or removing the
7. Do not pull mower backwards
unless absolutely necessary. Look
down and behind before and while
moving backwards.
mulcher cover or the optional grass
catcher. Make certain that the grass
catcher is securely attached before
operating the mower. Empty the
grass catcher after each use–
decomposing debris could generate
enough heat to catch fire.
8. Do not operate the mower without
proper guards, plates, grass catcher
or other safety protective devices in
place.
3. Only allow responsible individuals,
who are familiar with the instruc-
tions, to operate the mower.
9. Refer to provided instructions for
proper operation and installation of
accessories. Only use accessories
that are factory-approved.
4. Clear the area of objects such as
rocks, toys, wire, bones, sticks, etc.,
which could be picked up and
thrown by the blade.
13. Mow in daylight or good artificial
light.
10. Stop the blade when crossing gravel
drives, walks, or roads.
14. Do not operate the mower while
under the influence of alcohol or
drugs.
11. Stop the engine and disconnect the
spark plug wire from the spark plug-
whenever you leave the unit, before
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Safety
15. Never operate mower in wet grass.
Always be sure of your footing; keep
a firm hold on the handle and walk;
never run.
II. SLOPE OPERATION
IV. SERVICE
1. Use extra care in handling gasoline
and other fuels. They are flammable
and their vapors are explosive.
Slopes are a major factor related to
slip and fall accidents which can result
in severe injury. All slopes require
extra caution. If you feel uneasy on a
slope, do not mow it.
16. Disengage the Wheel Drive Lever on
self-propelled models before starting
the engine.
a) Use only an approved container.
b) Never remove gas cap or add
fuel when the engine is running.
Allow engine to cool before refu-
eling. Do not smoke.
c) Never refuel the machine
indoors.
d) Never store the machine or fuel
container inside where there is
an open flame, such as a water
heater, etc.
e) Move mower away from any
gasoline fumes before starting
the engine.
17. If the unit should start to vibrate ab-
normally, stop the engine and dis-
connect the spark plug wire. Then
check immediately for the cause.
Vibration is generally a warning of
trouble.
DO:
Mow across the face of slopes; never
up and down. Exercise extreme cau-
tion when changing direction on
slopes. Avoid slopes greater than
18. Always wear safety goggles or safety
glasses with side shields when oper-
ating mower.
19. Watch for traffic when operating
near, or when crossing roadways.
o
15 .
Remove objects such as rocks, tree
limbs, etc.
20. Never attempt to carry children or
other passengers on the mower.
They could fall off and be seriously
injured, or they could interfere with
the safe operation of the mower.
2. Never run an engine inside a closed
area.
Watch for holes, ruts, or bumps. Tall
grass can hide obstacles.
3. Never make adjustments or repairs
with the engine running. Disconnect
the spark plug wire and keep the
wire away from the plug to prevent
accidental starting.
DO NOT:
21. Check the operation of the Operator
Presence Control Bar before each
use. See the Maintenance Section of
this manual for instructions. If the
engine runs longer than three sec-
onds after the Operator Presence
Control Bar is released, the system
is not working properly. Immediately
contact your local White Outdoor
Dealer for instructions. Do not use
the mower until the mechanism is
repaired.
Do not mow near drop-offs, ditches,
or embankments. The operator could
loose footing or balance.
4. Keep all nuts and bolts, especially
the blade attachment bolts, tight and
keep equipment in good condition.
Do not mow excessively steep slopes.
Do not mow on wet grass. Reduced
footing could cause slipping.
5. Never tamper with safety devices.
Check their operation regularly.
III. CHILDREN
6. Keep mower free of grass, leaves or
other debris build-up. Clean up oil or
fuel spillage. Allow mower to cool
before storing.
Tragic accidents can occur if the opera-
tor is not alert to the presence of chil-
dren. Children are often attracted to the
mower and to the mowing activity.
Never assume that children will remain
where you last saw them.
22. The mower is equipped with a safety
discharge chute, comes with special
mulcher covers, and offers an op-
tional grass catcher. The safety dis-
charge chute must be working prop-
erly at all times. Never attempt to
disconnect or otherwise cause this
discharge chute to cease working. If
used, mulcher cover or grass
7. After striking an object, stop the en-
gine and disconnect the spark plug
wire. Inspect the mower and repair,
if necessary, before restarting.
1. Keep children out of the mowing
area and under the watchful care of
a responsible adult.
8. Never attempt to make mower cut-
ting height adjustments while the
engine is running.
2. Be alert and turn mower off if chil-
dren enter the area.
9. Grass catcher components are sub-
ject to wear, damage and deteriora-
tion, which could expose moving
parts or allow objects to be thrown.
Frequently check components and
replace with factory recommended
parts, when necessary.
catcher attachment must be installed
properly and function correctly. Do
not use your equipment otherwise.
3. Before and while moving backwards,
look behind and down for small
children.
23. Never run the engine in an enclosed
area. Engine exhaust contains carbon
monoxide, a deadly gas that is odor-
less, colorless, and tasteless. Always
run the engine outdoors and make
sure there is adequate ventilation.
4. Never allow children to operate the
mower.
5. Use extra care when approaching
blind corners, shrubs, trees, or other
objects that may obscure vision.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 1: Safety
13. To access the underside of the
mower, tip the mower rearward. Do
not tip the mower forward or on ei-
ther of its sides, unless specifically
advised to do so in this manual.
b) Do not use a battery charger
other than the one provided with
the mower.
c) The battery contains toxic mate-
rials. Do not damage the battery
case. If the case is broken or
damaged, avoid contact with the
battery contents.
d) Properly dispose of a damaged
or worn out battery. Check with
local authorities for proper dis-
posal methods.
e) Do not short circuit the battery.
Severe burns and fire can result.
10. Mower blades are sharp and can cut.
Wrap the blade or wear gloves, and
use extra caution when servicing
them.
14. Maintain or replace safety and in-
structional decals. Refer to the sep-
arate Parts Book for replacement
decal information.
11. Do not change the engine governor
setting or overspeed the engine.
15. For units equipped with electric
start:
12. Do not touch engine parts which
may be hot from operation. Allow
parts to cool completely before in-
specting, cleaning or repairing the
mower.
a) Batteries produce explosive
gases. Keep sparks, flame,
cigarettes, etc., away. Ventilate
the area when charging the bat-
tery. Do not charge the battery in
an airtight space.
SAFETY DECALS
Make certain all safety decals on this equipment are kept clean and in good condition. The decals are shown (at reduced sizes)
below. If you need a replacement decal, please refer to the Parts Book that accompanied this Manual.
PLACE FOOT ON TIRE WHEN STARTING
CAUTION
PINCH POINTS.
WARNING
WARNING
MAXIMUM SAFE OPERATING
OBJECTS MAY BE THROWN
FROM MOWER.
ANGLE IS 15O.
Do not operate with-
out all belt guards in
place.
• Exceeding maximum safe
operating angle may cause
tipping or loss of footing.
• Before mowing, clear lawn
of all debris.
• Disengage wheel drive
before adjusting height.
• Do not mow on wet slopes.
• Mow across slopes, not up
and down
1915475.A (11/97)
On top, rear of engine platform
WARNING
TO AVOID SERIOUS INJURY READ ALL SAFETY
PRECAUTIONS CAREFULLY.
Beneath belt/pulley
cover
4
3
•
•
Read owner/operator manual.
2
Do not allow children or untrained adults to
operate machine.
1
LIFT FOR
REVERSE
N
•
•
Use caution when approaching obstacles that
block your view.
R
Keep all safety devices in place and in working
order.
RELEASE OPERATOR
PRESENCE CONTROL
TO DISENGAGE
MOWER.
•
•
Do not mow when children or others are near.
Disengage wheel drive before adjusting height.
On Control Panel (for electric start model)
DANGER
KEEP HANDS and FEET AWAY
WARNING
TO AVOID SERIOUS INJURY READ ALL SAFETY
PRECAUTIONS CAREFULLY.
4
3
•
•
Read owner/operator manual.
2
Do not allow children or untrained adults to
operate machine.
1
LIFT FOR
REVERSE
N
•
•
Use caution when approaching obstacles that
block your view.
R
A
Keep all safety devices in place and in working
order.
RELEASE OPERATOR
PRESENCE CONTROL
TO DISENGAGE
MOWER.
On left side of
mower deck
•
•
Do not mow when children or others are near.
Disengage wheel drive before adjusting height.
On Control Panel (for recoil start model)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Se2ction
Assembly
the air cleaner cover and lift the other
handlebar upward. Rotate the handle-
bars over the engine and position the
handlebar ends (E, Figure 2-2) against
the sides of the engine deck.
ASSEMBLY STEPS
WARNING
IMPORTANT: MOTOR OIL MUST BE
ADDED TO THE ENGINE BEFORE IT IS
STARTED. FOLLOW INSTRUCTIONS IN
THIS “ASSEMBLY” SECTION.
To prevent personal injury or property
damage, do not attempt to start the
engine until all assembly steps are
complete and you have read and
understand the safety, controls and
operating instructions in this manual.
NOTE: Four screws (D, Figure 2-2) are
used to connect the handlebars to the
engine deck. The screws thread into
lock nuts welded to the back sides of the
deck.
STEP 1: Unpacking Mower
NOTE: LEFT and RIGHT sides of the unit
are as viewed from the operator’s posi-
tion behind the handlebars.
INTRODUCTION
3. Swing the handlebar struts (A, Figure
2-2) forward and align the handlebar
ends (E, Figure 2-2) with the holes in the
engine deck. Loosely install two 5/16"-
18 x 3/4" hex flange screws (D) into the
rear holes.
Please carefully follow these assembly
steps to properly prepare your machine
for use. We recommend that you read
this Section in its entirety before begin-
ning assembly.
1. Cut plastic banding, open box flaps
and remove cardboard liners. Remove
any staples securing carton to wood pal-
let and lift off carton. Cut metal straps
securing unit to pallet. Leave unit on pal-
let during assembly (to safely remove
unit from pallet, wait until you have com-
pleted assembly steps 1-4).
NOTE: All references to left, right, front
and rear of the machine are determined
by standing behind the handlebars and
facing the direction of forward travel.
4. Align the loose ends of the handlebar
struts (A, Figure 2-2) over the front
holes in the handlebar ends. Attach the
struts and handlebars with two more
5/16"-18 x 3/4" hex flange screws.
Securely tighten all four screws.
2. Remove hardware bag and check
contents against illustrated parts list on
next page.
INSPECTION AFTER DELIVERY
When unpacking the machine, inspect
for shipping damage or missing parts. If
you find any damage, or if parts are
missing, notify the White Outdoor Dealer
who sold you the machine.
5. Securely tighten the screws (B, Figure
2-1) at the upper ends of the struts.
3. Remove any protective packaging
from around the handlebars. Cut the
plastic tie straps holding the four long
control rods to the handlebars. Do not
remove the two long handlebar struts
that are attached to the top of the
handlebars.
6. Secure the engine throttle cable (C,
Figure 2-1) to the left handlebar with a
cable tie. Clip off any excess tie length.
TOOLS/MATERIALS NEEDED:
• Wire Cutter
• 7/16” Wrench
• 3/8” Wrench
• Two 1/2” Wrenches
• Scissors or Pen Knife
• Needle-nose Pliers
• Motor Oil (see Step 5)
• Tire Gauge
4. Check for any small parts before dis-
carding the carton or cardboard liners.
B
A
STEP 2: Attach Handlebars
to Engine Deck
1. Remove the plastic ties holding the
wheel drive rod (F, Figure 2-7) to the left
handlebar and the blade drive rod (C,
Figure 2-7) to the right handlebar. Put
the rods aside.
A
B
C
2. Remove and save the two 5/16"-18 x
3/4" screws securing the handlebar ends
to the rear of the engine deck. To free
the handlebars, first raise the two han-
dlebar struts (A, Figures 2-1 and 2-2) to
a 450 angle. Then, from the front of the
unit, tilt the right-side handlebar up over
Figure 2-1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Assembly
Contents of Hardware Bag
(Parts are shown at actual size unless noted otherwise)
Cotter Pin, 3/32" x 5/8"
Qty: 6
Hex Flange Lock Screw,
1/4"-20 x 1/2" Qty: 2
Hex Flange Lock Screw,
5/16"-18 x 3/4" Qty: 2
Flat Washer, 5/16"
Qty: 4
Hex Flange Lock Nut,
1/4-20" Qty: 2
Plastic Cable Tie
(shown reduced size)
Qty: 1 (Recoil Start Model)
Qty: 3 (Electric Start Model)
Shift Link - Gear Select Lever
(shown reduced size) Qty: 1
Shift Rod Mounting Plate
(shown reduced size) Qty: 1
Oil Drain Tube (shown reduced size) Qty. 1
( for changing oil - see Maintenance Section )
(Parts shown below are for electric start model)
Battery Charger Qty: 1
(shown reduced size)
Ignition Keys Qty: 2
(shown reduced size)
B. Attach Wire Leads to Battery
STEP 3: Electric Start Model
A. Secure Wire Harness
1. The battery is located at the rear,
A
right-side of the engine deck.
1. At the unattached end of the electrical
wire harness, there are four wires at-
tached to a large plastic connector and
two wires attached to a small plastic
connector. Plug the large connector into
the bottom of the ignition keyswitch that
is located on the underside of the han-
dlebar console (not pictured).
2. At the lower end of the electrical
wiring harness, locate a red wire lead
and a black wire lead.
• Plug terminal on red (positive) wire into
red terminal (U, Figure 2-3) on battery.
E
• Plug terminal on black (negative) wire
into black terminal (V).
D
D
2. Use two cable ties to secure the wire
harness to the right handlebar and away
from any moving parts. Place the ties an
equal distance apart.
Figure 2-2: Attach handlebars and struts
to engine deck.
3. If applicable, attach wire harness to
engine deck using J-clips (W, Figure
2-4) as shown. Bend J-clips over to
secure.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Assembly
1. To charge the battery, locate the plas-
tic connector (T, Figure 2-5) that hangs
from the wire harness below the handle-
bar console.
STEP 4: Attach Control Rods
Black(GroundLead)
(-)
V
WARNING
Control rods are adjusted at the factory
and should not require additional ad-
justment during assembly. After as-
Red
(Positive
(
Lead)
2. Plug the connector on the battery
charger (Z, Figure 2-5) into the connec-
tor on the wire harness (T).
sembling
unit,
control
rod
(+)
U
adjustment should be checked (and
re-adjusted, if necessary) according to
information in Maintenance Section.
3. Plug the battery charger into a 120V
grounded wall outlet. NOTE: The battery
charger is designed for use indoors and
should not be exposed to rain or snow.
Figure 2-3: Connect wire terminals to
battery terminals.
Failure to follow this instruction could
result in severe personal injury or
property damage.
W
4. Charge battery for 24-48 hours.
5. After charging, unplug battery
charger from wall outlet, then unplug
charger from wire harness.
A. Attach Wheel Drive Control Rod
1. Locate the wheel drive control rod (F,
Figures 2-6 & 2-7) that was removed
from the left handlebar in Step 2. This
rod has a swivel block (H, Figure 2-6) on
one end.
Figure 2-4: Attach wire harness with J-
clips.
2. At left side of engine deck, insert
swivel block (H, Figures 2-6 & 2-7) on
wheel drive control rod into wheel drive
control arm (U, Figure 2-6).
T
Z
WARNING
3. Add a 5/16" washer (A, Figure 2-6)
and attach with a cotter pin (B). Bend
legs of cotter pin over rod to secure.
Charge battery only with charger sup-
plied with machine. Do not short circuit
battery wires. Remove any jewelry be-
fore working on or near the battery or
electric start system.
To grounded
wall outlet
4. At upper end of control rod, insert
angled end into Wheel Drive Control
lever (V, Figure 2-6A) and attach with a
cotter pin (BB). Bend ends of cotter pin
over rod to secure.
Figure 2-5
Failure to follow these instructions
could result in personal injury or prop-
erty damage.
C. Charge the Battery
E
Charge a new battery for 24-48 hours to
ensure a full charge. If the mower must
be used immediately, the battery may
have enough of a charge to start the en-
gine. If not, the engine can be started
with the rope pull starter. NOTE: Charge
the battery after the initial use of the
mower to help ensure it is fully charged.
F
W
U
CAUTION
If battery is removed, do not operate
engine without insulating positive (+)
battery cable terminal with electrical
tape or sparking from battery cells can
result.
G
T
H
A
B
Figure 2-6: Left-hand control rods detail.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Assembly
BB
L
W
V
J
AA
V
F
Figure 2-6A: Attach wheel drive control rod
to lever.
I
B. Attach Operator Presence Control
Rod
E
1. Locate control rod (E, Figures. 2-6
and 2-7) attached at upper end to
Operator Presence Control lever (W,
Figure 2-7).
C
F
2. At bottom of control rod, insert
swivel block (G, Figures 2-6 & 2-7) into
control arm (T, Figure 2-6).
CC
3. Add one 5/16" washer and attach with
cotter pin. Bend ends of cotter pin to se-
cure.
H
D
C. Attach Blade Drive Control Rod
1. Locate the blade drive control rod (C,
Figure 2-7) that you removed in Step 2.
Insert one end of control rod into blade
drive bracket (D, Figure 2-7). Add one
5/16" washer and attach with cotter pin
(CC). Bend ends of cotter pin to secure.
N
G
M
P
O
Figure 2-7: Rear view of control rods.
B
2. Insert upper end of rod into bottom
end of Blade Drive Control lever (J,
Figure 2-7). Add one 5/16" washer and
attach with cotter pin (AA). Bend ends of
cotter pin to secure.
I
L
Z
D. Attach and Adjust Gear Select Lever
1. Using the edge of a piece of flat wood
(such as a ruler), remove the vinyl grip
(B, Figure 2-8) from the gear select lever
(I). Place the wood edge against the
edge of the grip and slowly pull off the
grip.
J
P
K
Pin (K) must be in this detent
when transmission neutral is
adjusted.
2. Insert nylon bushing (Z, Figure 2-8)
up into console (L).
3. Slide spring and washers (J) down
onto gear select lever.
4. Insert gear select lever (I) up through
nylon bushing (Z) in handlebar console
(L). Guide pin (K) on gear select lever into
groove in shift quadrant (P).
Figure 2-8: Detail – Gear Select Lever in Neutral (N) position.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 2: Assembly
5. Hold lower part of gear select lever (I,
Figure 2-9) against bracket (M). Position
retaining plate (N) from parts bag in
place as shown in Figure 2-9 (plate
below bracket). Secure plate with two
1/4"-20 x 1/2" screws (O) and 1/4”-20
locknuts.
and backward. The wheels should move
freely. If not, adjust length of shift link
(P, Figure 2-9) as necessary.
WARNING
Do not use the mower if the wheels
continue to turn after releasing the
Operator Presence Control and the
Wheel Drive Control.
14. Put the Gear Select Lever in neutral
(N), release all of the control levers and
try to push the unit forward and back-
ward. The wheels should not turn. If
they do turn, an adjustment is neces-
sary. DO NOT OPERATE THE UNIT
UNTIL THE WHEEL BRAKE MECHANISM
HAS BEEN ADJUSTED AND IS WORK-
ING PROPERLY. See “Wheel Brake
Adjustment” in Section 5 “Maintenance.”
Severe personal injury or property
damage could result if this instruction
is not followed.
6. Slide grip (B, Figure 2-8) back onto
gear select lever (I).
7. Rotate gear select lever (I, Figures 2-
8 & 2-9) clockwise until spur (K - short
rod) on gear select rod stops in the neu-
tral position detent on the shift pattern
quadrant (Figure 2-8).
I
8. At bottom of control rod, thread shift
link (P, Figure 2-9) partially into ball-joint
(Y).
O
9. Move shift arm (X, Figure 2-9) from
side to side as necessary into each
transmission gear detent until transmis-
sion is in neutral.
NOTE: Moving shift arm (X) all the way to
the left, and then one notch back to the
right, should put transmission into neu-
tral. When transmission is in neutral, unit
will move freely when pushed while hold-
ing the Operator Presence Control lever
(W, Figure 2-7) down. If transmission is
NOT in neutral, there will be a slight drag
on the wheels when pushing unit.
N
M
Y
Q
X
P
10. When shift arm (X) is in neutral po-
sition, rotate shift link (P) toward end of
gear select lever rod (I). Adjust length of
shift link (P) as necessary to fit into hole
in bottom of gear select lever (I).
Figure 2-9: Detail – Transmission Neutral Adjustment.
STEP 6: Check Tire Pressure
CAUTION
1. Use a tire gauge to check the air
pressure in the rear tires. The air pres-
sure should be between 15-20 PSI (20
PSI maximum).
Unit is shipped without oil in engine
crankcase. Do not start engine until oil
has been added. Severe engine dam-
age will result if this instruction is not
followed.
NOTE: Pin (K) on Gear Select Lever (I)
must be held in the neutral position
detent on the shift quadrant (see Figure
2-8) while shift link (P, Figure 2-9) is
adjusted.
2. Keep both tires equally inflated to
help prevent machine from pulling to
one side.
11. Insert hooked end of shift link (P,
Figure 2-9) into hole in bottom end of
gear select lever (I) and secure with cot-
ter pin (Q). Bend ends of cotter pin.
NOTE: It may be necessary to lift gear
select lever (I) to install shift link (P).
STEP 5: Add Motor Oil to Engine
1. Move mower to a level area. Press
and hold Operator Presence Control
lever (W, Figure 2-7) to move mower.
STEP 7: After Assembling and
Before Using Unit
1. Read this entire Operator’s Manual
for proper safety, operation and mainte-
nance information.
2. Add motor oil according to the specifi-
cations and instructions provided in the
separate Engine Owner’s Manual that was
included in the unit’s literature package.
12. Remove unit from shipping crate.
To remove, hold down Operator
Presence Control lever (W, Figure 2-7)
which releases the wheel brake.
2. Make sure spark plug wire is con-
nected to spark plug before starting unit.
• Keep oil level at the FULL mark on the
dipstick to avoid engine damage.
13. With unit on level ground, hold
down Operator Presence Control lever
(W, Figure 2-7) and push unit forward
• Change oil according to schedule and
instructions in Section 5 “Maintenance.”
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Se3ction
Features and Controls
the lever will also disengage the Blade
MOWER FEATURES AND
CONTROLS
WARNING
Drive Control, which will apply a brake
that stops the blades within three (3)
seconds.
Before operating mower, be sure to
read all safety, controls and operating
instructions in this Manual and on
decals located on machine.
This section describes the various
features and controls on the unit. Refer
to the next section “Operation” for
detailed operating instructions. Also,
read the separate Engine Owner’s
Manual for a detailed explanation of the
proper use of the engine controls.
Blade Drive Control
Use this lever (B, Figure 3-1) to en-
gage drive to the mower blades.
To engage the blades, first engage the
Operator Presence Control (A, Figure 3-
1). Then, push the spring-loaded Blade
Drive Control lever (B) forward until it
stays in the engaged position.
Severe personal injury or property
damage could result if this instruction
is not followed.
Operator Presence Control
IMPORTANT: THE MOWER IS
EQUIPPED WITH A BLADE-BRAKE-
CLUTCH CONTROL SYSTEM WHICH IS
DESIGNED TO STOP THE MOWER
BLADES WITHIN THREE (3) SECONDS
AFTER RELEASE OF THE OPERATOR
PRESENCE CONTROL. THIS SYSTEM
WILL STOP THE BLADES BUT NOT THE
ENGINE. THEREFORE, YOU CAN DISEN-
GAGE THE BLADE DRIVE AT ANYTIME
WITHOUT HAVING TO STOP AND
RESTART THE ENGINE. THIS FEATURE
IS PARTICULARLY USEFUL WHEN YOU
NEED TO CROSS GRAVEL DRIVES OR
ROUGH TERRAIN AND YOU DO NOT
WANT THE SPINNING BLADES
TO STRIKE STONES OR HIDDEN
OBSTACLES.
The Operator Presence Control lever
(A, Figure 3-1) regulates the operation of
the rear wheel brake and the separate
Blade Drive Control. Always engage this
control before engaging the separate
blade drive or wheel drive controls.
Always disengage this control before
starting the engine.
To engage the Operator Presence
Control, press and hold the lever against
the handlebar grip. Doing so releases
the brake on the rear wheels, allowing
the wheels to turn. The engaged position
also permits the separate Blade Drive
Control to lock in its engaged position
(allows the mower blades to turn).
Releasing the lever (disengaged
To stop the blades, release the
Operator Presence Control (A). Doing so
will disengage the Blade Drive Control
(B) and automatically apply the brake
that stops the blades.
Always disengage the Blade Drive
Control before starting the engine. This
helps to ensure that the blades will not
start turning when the engine starts.
NOTE: Pushing the Blade Drive Control
forward will engage the blades even
though the Operator Presence Control is
not engaged. However, this procedure is
NOT RECOMMENDED as you must main-
tain constant pressure on the lever (re-
leasing lever disengages blades). Always
engage the Operator Presence Control
before engaging the Blade Drive Control.
position) applies the rear wheel brake
and quickly stops the wheels. Releasing
WARNING
A – OPERATOR
PRESENCE CONTROL
The blade-brake-clutch control system
should stop the mower blades within
three (3) seconds after release of the
Operator Presence Control.
B – BLADE
DRIVE CONTROL
C – GEAR
SELECT LEVER
Disengage
Engage
If the blades do not stop within three
(3) seconds, put the Engine Throttle
Control in the STOP position.
Disconnect the spark plug wire and do
not operate the mower until the blade-
brake-clutch control system has been
repaired.
Disengage
Engage
Figure 3-1
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Features and Controls
Operating Symbols Various symbols are used on the mower to indicate control settings (your model may not have all of the
symbols). These symbols are shown below with a description of their meaning.
ENGINE
STOP
ENGINE
START
ENGINE
RUN
FAST
SLOW
ENGAGE
DISENGAGE
CHOKE
Presence Control along with the Wheel
Drive Control.
When starting the engine, the Wheel
Drive Control should be disengaged (re-
leased). This helps to ensure that the
wheels will not start turning when the
engine starts.
trated) on the right side of the mower
deck show the cutting height settings
ranging from A (highest) to G (lowest).
Gear Select Lever
Use this lever (C, Figure 3-1) to select
any of four forward ground speeds (1 -
Slow, 2 and 3 - Medium, 4 - Fast), N
(Neutral) and R (Reverse). The gear shift
pattern is shown in Figure 3-2.
To avoid damaging the transmis-
sion, do not shift gears when the
mower is moving.
For forward travel, use one of the four
numbered settings. To select reverse,
shift to neutral and then pull up on the
lever. Turn the lever to the R (reverse)
position and release the lever.
Put the lever in N (neutral) to manu-
ally push the mower and when the
mower is not in use.
E – CUTTING HEIGHT
CONTROL LEVER
CAUTION
Do not engage the Wheel Drive Control
without first engaging the Operator
Presence Control. Doing so could
result in wear or damage to the wheel
brake mechanism.
Figure 3-4
Mulcher Cover
The mulcher cover (F, Figure 3-5) is
pre-installed at the factory. It must be
kept in place when using the unit as a
mulching mower. The mulcher cover is
designed to keep the discharge chute
raised up while you mow. When the
cover is removed for side-discharge
mowing, the discharge chute lowers.
Refer to “4. Select Mulching or Side-
Discharge Mowing” in the Operation
Section for mulcher cover installation
instructions.
A – OPERATOR
PRESENCE CONTROL
4
3
2
Figure 3-2:
Shift pattern
on console.
Disengage
Engage
1
LIFT FOR
REVERSE
N
R
Engage
Wheel Drive Control
Use this lever (D, Figure 3-3) to en-
gage and disengage drive to the wheels.
To engage the wheels, first select a
forward or reverse gear with the Gear
Select Lever and squeeze the Operator
Presence Control (A, Figure 3-3). Then,
squeeze the Wheel Drive Control lever
(D) against the handlebar grip. The
ground speed can be varied by increas-
ing or decreasing pressure on the lever.
To avoid sudden acceleration, slowly
squeeze the lever when first engaging
the wheels.
Disengage
D – WHEEL
DRIVE CONTROL
Figure 3-3
F
Cutting Height Control Lever
Figure 3-5
Use this lever (E, Figure 3-4) to adjust
the cutting height from 1 to 4 inches.
Note that actual cutting heights will vary
according to soil conditions.
Turn the lever clockwise to raise the
height or counterclockwise to lower the
height. A decal and pointer (not illus-
Release the Wheel Drive Control to
disengage the wheels. The wheels will
gradually slow to a stop. NOTE: To stop
the wheels quickly, release the Operator
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 3: Features and Controls
Engine Throttle Control
H – IGNITION/STARTER
SWITCH
This lever (G, Figure 3-6) is used to
adjust engine speeds and to stop the en-
gine. Always run engine at fast speed
setting for best mower performance.
The throttle settings are shown below.
G – THROTTLE CONTROL
CHOKE - Use when
starting a cold engine.
FAST - Use during mower
operation.
Figure 3-6
SLOW - Use when idling
engine.
Engine Recoil Starter
The recoil starter (I, Figure 3-7) is
used to “pull-start” the engine. Detailed
instructions for using the recoil starter
are found in the Operation Section of this
Manual and in the Engine Owner's
Manual. Do not pull the recoil starter
until you have read the Operation
Section.
STOP - Stops engine.
Ignition/Starter Switch -
(Electric Start Model)
This three-position switch (H, Figure
3-6) is used to start and stop the
engine on electric start models. The ig-
nition key settings are shown below. Do
not turn the key until you have read the
Operation Section in this Manual.
Always remove ignition key when
leaving mower unattended or when in-
specting, cleaning or servicing mower.
I – RECOIL
STARTER
Figure 3-7
STOP - Stops engine.
RUN - After starting, key
returns to run position.
START - Starts engine.
Release key when engine
starts.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Se4ction
Operation
9. Check the air pressure in the rear
clean unleaded gasoline with a mini-
mum octane rating of 77. Leave 1/2"
of space for fuel expansion. Do not
mix oil with gasoline. Do not use
gasoline which contains Methanol.
See the Engine Owner’s Manual for
instructions and precautions regard-
ing the use of gasolines that are
blended with alcohols or ethers
(called oxygenated or reformulated
gasolines). Securely replace caps on
fuel tank and fuel container.
WARNING
tires (15-20 PSI). Keep tires inflated
equally.
Before operating mower, be sure to
read all safety, controls and operating
instructions in this Manual and on
decals located on machine.
DANGER
GASOLINE IS HIGHLY FLAMMABLE AND
ITS VAPORS ARE EXPLOSIVE. To help
prevent severe personal injury or prop-
erty damage:
Severe personal injury or property
damage could result if this instruction
is not followed.
• Follow gasoline safety rules in
Section 1: “Safety” of this Manual and
in the separate Engine Owner’s
Manual.
BEFORE OPERATING MOWER
1. Pre-Operation Checklist
11. Attach spark plug wire to spark plug
after completing above checklist.
With the spark plug wire disconnected
from the spark plug, perform the follow-
ing checks and services before each use:
• Never remove the gasoline fill cap or
add fuel when indoors or when engine
is running or still hot. Allow engine to
cool at least three (3) minutes before
refueling.
2. Set Mower Cutting Height
1. Review Section 1: “Safety” and Section
3, “Features and Controls” in this
CAUTION
To avoid personal injury, do not adjust
cutting height while wheels or blades
are turning. Release all handlebar
controls and wait for all motion to stop
before adjusting cutting height.
Manual. Read the separate Engine
Owner’s Manual provided with the unit.
• Keep smoking materials, sparks or
flames far away from fuel tank and fuel
container.
2. Check unit for loose or missing hard-
ware. Tighten or replace as needed.
• Store gasoline in an approved fuel
container and in a well-ventilated area.
Store it safely out of the reach of chil-
dren. Do not store gasoline where va-
pors can reach an open spark or flame
or where ignition sources are present
(such as hot water or space heaters,
furnaces, clothes dryers, stoves, elec-
tric motors, etc.).
3. With the unit on level ground, check
the engine oil level according to the
instructions in the Engine Owner’s
Manual. The oil level should be at the
FULL mark on the dipstick or up to the
top of the oil fill hole on engines with-
out a dipstick.
1. Release all controls before adjusting
the cutting height.
2. Adjust the cutting height from 1 to 4
inches by rotating the Cutting Height
Control lever (Figure 3-4) either clock-
wise to raise the height or counterclock-
wise to lower the height. Note that ac-
tual cutting heights will vary according
to grass and soil conditions. A decal and
pointer on the right side of the mower
deck indicates the height setting.
4. Check all levers for freedom of move-
ment. Readjust or repair as needed
before starting engine.
• Fill tank to 1/2" below bottom of filler
neck to allow for fuel expansion. Wipe
up spilled gasoline immediately and
move mower away from gasoline fumes
before starting engine. Securely re-
place caps on fuel tank and fuel
container.
5. Check that all guards and shields are
in place and properly secured.
6. Inspect the area to mowed and re-
move any debris which could be
picked up and thrown by the mower
blades.
3. In heavy or tall grass, it is usually
better to make the first cut at a higher
setting and then make a second cut at
the desired height. In rough terrain, a
higher setting is recommended as it will
minimize the chances of the blade strik-
ing the ground or hidden obstructions.
10. Remove the fuel cap and check the
level of gasoline according to the in-
structions in the Engine Owner’s
Manual. Clean around fuel fill area
before removing fuel cap. Do not
check fuel level or add fuel while in-
doors or if engine is running or hot.
Allow engine to cool for three (3)
minutes. Fill the tank with fresh,
7. Check that the mulcher cover is prop-
erly installed in the discharge opening
(see instructions in this Section).
Remove the mulcher cover to use the
side-discharge mowing feature.
8. On electric start models, check that
all wiring connections are clean and
tight.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
3. Test Blade-Brake-Clutch
Control System
STARTING AND STOPPING
THE ENGINE
The mower is equipped with a blade-
brake-clutch which is designed to stop
the mower blades within three (3)
seconds after release of the Operator
Presence Control or the Blade Drive
Control. Never tamper with, or attempt
to defeat the purpose of this safety
device.
The control system is a mechanical
device which is subject to wear.
Therefore, test the operation of the
blade-brake-clutch control system before
each use of the mower. Refer to "Blade
Brake Control Test" at the end of this
Section.
DANGER
Do not operate the engine in an
enclosed area. Engine exhaust
contains carbon monoxide, a deadly
gas that is odorless, colorless and
tasteless. Always run engine outdoors
and make sure there is adequate
ventilation.
A
B
Figure 4-1: Mulcher cover
3. To remove the cover, slide the cover
to the right (front of mower) to disen-
gage the slot (B) from the mower deck
and then pry the left-side of the cover
out and off.
To Start the Engine
1. Move mower to a level area.
2. Release all controls on mower to pre-
vent wheels or mower blades from rotat-
ing when engine starts.
4. Select Mulching or Side-
Discharge Mowing
MOVING THE MOWER WITHOUT
ENGINE POWER
3. Move Engine Throttle Control (E,
Figure 4-2) fully upward to choke setting
to start a cold engine or to fast (rabbit)
setting to start a warm engine.
WARNING
The mower can be manually pushed
or pulled by putting the Gear Select
Lever (C, Figure 4-2) in N (neutral) and
pressing and holding the Operator
Presence Control (A, Figure 4-2) down
against the handlebar grip.
Before installing or removing mulching
cover, stop engine, wait for parts to
stop moving, and disconnect spark plug
wire. Remove ignition key on electric
start models.
WARNING
To avoid injury:
• Keep hands and feet clear of mower
blades or other rotating parts.
• Look behind you to be sure there are
no obstacles before pulling recoil
starter rope.
To stop the wheels at anytime,
release the Operator Presence Control.
You can use the mower either as a
mulching mower or as a side-discharge
mower. To use the mulching feature, in-
sert the mulcher cover as described
below. Remove the mulcher cover to
side-discharge grass clippings. The
mulcher cover is designed to keep the
discharge chute raised up while mowing.
When the cover is removed, the dis-
charge chute will lower itself for side-
discharge mowing.
C – Gear Select Lever
E – Engine Throttle
Control
F – Ignition/Starter
A – Operator
Presence Control
To install or remove mulcher cover:
B – Blade Drive
Control
1. Stop the engine and wait for all parts
to stop moving. Disconnect the spark
plug wire from the spark plug. Remove
the ignition key on electric start models.
2. To install the cover, insert the right-
side tab of the cover into the front sup-
port bracket (A, Figure 4-1). Insert the
cover into the discharge opening, mak-
ing sure that the slot (B) in the left side
of the cover is completely engaged in the
rear edge of the deck opening.
D – Wheel Drive Control
Figure 4-2: Mower Controls
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
4. To start engine using recoil starter:
3. Move Throttle Control all the way
down to stop position or turn ignition
key (electric start models) fully counter-
clockwise to stop position.
Fast). When first practicing with the
mower, put lever in No. 1 setting.
Select forward speeds according to
mowing conditions and terrain. Use
slower speeds on rough terrain or
when grass is heavy or thick. The
forward speed can be increased on
smooth terrain or if the grass cover is
light. Allow the wheels to stop com-
pletely before shifting from one for-
ward speed into another.
A. Stand on left side (as viewed from be-
hind handlebars) of machine. Be sure
your feet are safely away from the
underside of the mower deck and all
mower controls are released. Place
one foot on top of tire.
4. On electric start models, remove the
ignition key before leaving the mower
unattended.
B. Grasp starter rope handle (Figure 3-7)
and pull slowly until rope pulls
slightly harder. Let rope rewind
slowly. Then pull rope with a rapid,
full arm stroke. Let rope return
slowly. If engine fails to start after
three pulls, repeat instructions start-
ing with Step 2 (try setting throttle at
fast setting).
ENGAGING THE BLADES
DANGER
To avoid injury from rotating blades,
keep face, hands and feet clear of
mower blades at all times.
WARNING
Before engaging the Wheel Drive Lever
for the very first time, check that the
neutral (N) position on the Gear Select
Lever is properly adjusted. See
“Neutral Adjustment” in Section 5:
Maintenance for the procedure to
follow.
C. When engine starts, operate in fast
throttle setting (move throttle from
choke setting to fast setting).
To Engage the Blades
1. Start engine as described in “To Start
the Engine” instructions. Put engine
throttle in fast speed setting.
5. To start engine using electric starter:
Failure to follow this instruction could
result in personal injury or property
damage.
A. Stand behind the handlebars and re-
2. Press and hold Operator Presence
Control (A, Figure 4-2) against handlebar
grip.
lease all mower controls.
B. Turn ignition key (F, Figure 4-2) fully
clockwise to crank engine. To avoid
damage to starter motor, do not
crank engine for longer than five sec-
onds at a time. Also, allow 15 sec-
onds between each start attempt. If
engine fails to start after three at-
tempts, repeat instructions starting
with Step 2 (try setting throttle at fast
setting).
3. Slowly push Blade Drive Control (B,
Figure 4-2) fully forward until it stays in
the engaged position. The blades are
now rotating.
C. To start the wheels, slowly squeeze
the Wheel Drive Control (D, Figure 4-
2). The harder you squeeze, the faster
the wheels will turn. To avoid sudden
acceleration, slowly squeeze the
lever.
To Stop the Blades
To stop the blades, release the Operator
Presence Control.
D. TO STOP THE WHEELS:
• To stop drive power to the wheels,
release the Wheel Drive Control. The
wheels will gradually slow to a stop.
C. When engine starts, release key and it
TO ENGAGE THE WHEELS
will return to the run (middle) position.
D. Operate engine at fast throttle setting
(move throttle from choke setting to
fast setting).
NOTE: If the electric start system is not
functioning, the engine can be started
with the recoil starter. To do so, first put
the ignition key in the run (middle) posi-
tion. Then follow Steps 1-4 above.
Leave the key in the run position during
engine operation.
CAUTION
• To avoid damaging the transmission,
do not shift gears while in motion.
• To quickly stop the wheels, release
both the Wheel Drive Control and
the Operator Presence Control.
3. FOR REVERSE TRAVEL:
• To avoid damaging the wheel brake
mechanism, do not engage the Wheel
Drive Control without first engaging the
Operator Presence Control.
WARNING
To avoid injury or property damage:
• Look behind the mower before
and during reverse operation.
1. Start engine as described in “To
Start the Engine” instructions.
• Stop the mower blades before operat-
ing in reverse.
To Stop the Engine
1. Release all mower controls to stop
wheels or mower blade.
2. FOR FORWARD TRAVEL:
A. Press and hold Operator Presence
Control (A, Figure 4-2) against han-
dlebar grip.
A. Stop the mower blades and wheels by
releasing the Operator Presence
Control (A, Figure 4-2).
2. Move throttle control down to slow
(turtle) position. (Whenever possible,
gradually reduce engine speed before
stopping engine.)
B. Put the Gear Select Lever (C, Figure
4-2) into one of the numbered set-
tings (1 - Slow, 2 and 3 - Medium, 4 -
B. Press and hold Operator Presence
Control against handlebar grip.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
C. Put the Gear Select Lever (C, Figure 4-
2) in R (reverse) setting by first mov-
ing lever to N (neutral). Then pull
lever up, turn it to R position, and re-
lease lever.
Mow When
Lawn Is Dry
WARNING
To avoid injury or property damage:
• Maximum safe operating angle
is 15o.
For best results, avoid cutting grass
when it is wet. Wet grass tends to form
clumps which interfere with the cutting
action. The best time to mow is in the
late afternoon or early evening when the
grass is usually dry.
D. To start the wheels, slowly squeeze
Wheel Drive Control (D, Figure 4-2).
To avoid sudden acceleration, slowly
squeeze the lever.
• Exceeding maximum safe operating
angle may cause tipping or loss of
footing.
• Do not mow wet slopes.
E. TO STOP THE WHEELS:
1
3
• Mow across slopes, not up and down.
• To stop drive power to the wheels,
release the Wheel Drive Control. The
wheels will gradually slow to a stop.
Cut Top 1/3 of
Grass Blades
• Exercise extreme caution when
changing direction on slopes.
• To quickly stop the wheels, release
both the Wheel Drive Control and
the Operator Presence Control.
Cutting more than 1/3 of grass length
may cause the grass to become exces-
sively dry. In tall grass, it may be neces-
sary to mow at a higher setting and then
mow again at the desired height. NOTE:
The cutting height is critical to achieving
a well-groomed lawn. You should exper-
iment with various settings to find that
“just right” cutting height.
Mulching Leaves
• The mower can be used to mow fallen
leaves. The leaf particles filter down into
the lawn and provide added fertilizer.
• The leaves must be dry in order to be
mulched.
• Return the Gear Select Lever to the
N (neutral) position when you have
completed reverse operation. Allow
the wheels to stop completely be-
fore shifting from R (reverse) into a
forward speed.
• Use a slower ground speed if the leaves
are not mulched into fine particles.
• If you mulch oak leaves (which add acid
to the soil), add lime to the lawn in the
spring to reduce the acidity of the soil.
MAKING TURNS
Vary Cutting Pattern
The mower turns easily by pushing
the handlebars in the opposite direction
that you want to turn. The differential
mechanism inside the transaxle will
allow the inside turning wheel to stop or
slow down while the outside turning
wheel is powered by the drive system.
Reduce the wheel speed before turn-
ing the mower. For tight turns, disen-
gage the Wheel Drive Control and manu-
ally push the mower through the turn (if
needed, put the Gear Select Lever in neu-
tral so the wheels turn freely).
Keep Mower Blades Sharp
For best mower performance, keep the
blades sharp. Dull blades will tear,
bruise and split the ends of grass. See
blade sharpening instructions in Section
5: Maintenance.
Vary the cutting pattern from week to
week to help prevent matting of the
grass. One week, mow from north to
south, the next week mow from east to
west. Overlap several inches when
mowing to obtain an even appearance.
Clean Mower Frequently
Clean the underside of the mower deck
frequently to remove grass build-up.
See mower cleaning instructions in
Section 5: Maintenance.
Mowing on Slopes
Precision Trimming
MOWING TIPS AND HINTS
Do not mow excessively steep slopes
(see WARNING statement that follows).
Slow down and exercise extreme caution
when changing direction on slopes.
Before mowing on slopes, check the en-
gine oil level and make sure that the level
is at the FULL mark. Maintaining a FULL
oil level is particularly important when
operating on slopes as oil can be drained
away from vital engine parts.
For precision trimming, use the slow-
est gear and inch the mower along by
“feathering” the Wheel Drive Control
lever. Or, disengage the wheel drive by
releasing the Wheel Drive Control so that
you can manually maneuver the mower
(if needed, put the Gear Select Lever in
neutral so that the wheels turn freely).
WARNING
To avoid injury or property damage:
• Before mowing, thoroughly inspect
area where mower is to be used and
remove all stones, sticks, wires,
bones, nails and other foreign objects.
Mowing Ditches
• Disengage mower blades before
crossing gravel drives, roads, or side-
walks to prevent blades from throwing
stones or other hazardous objects.
If you have to mow ditches, stop the
engine and adjust the cutting height to
its highest setting. Mow in the direction
of the ditch. Mow both sides of the ditch
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 4: Operation
first, and then mow the bottom. When
mowing ditches, watch out for cans,
bottles, or other debris.
1. Park mower on a portion of lawn
which has not been recently mowed.
8. Do not use the mower until the Blade
Brake Control System has been in-
spected, adjusted or repaired by an au-
thorized dealer.
2. Set the cutting height so the mower
cuts 1/3 of the grass height.
BLADE BRAKE CONTROL TEST
When the Operator Presence Control
is released during operation of the
mower, the engine does not stop, but the
blades should stop within three (3) sec-
onds. The following test provides a vi-
sual test of whether the Blade Brake
Control System is functioning. Perform
this test before each use of the mower.
3. Start the engine.
4. Press the Operator Presence Control
down against the handlebar grip and
push the Blade Drive Control fully for-
ward until it stays in the engaged posi-
tion.
5. Put the Gear Select Lever in the No. 1
setting.
6. Engage the wheels with the Wheel
Drive Control and drive the mower for
several feet. Then release the Operator
Presence Control.
WARNING
To avoid personal injury or property
damage, make sure that the mower is
on grass, and that the test area is clear
of foreign objects and bystanders be-
fore you begin the Blade Brake Control
Test.
A. Look at the lawn just mowed. The
lawn should be cut up to the point
where the Operator Presence Control
was released.
B. Press the Operator Presence Control
against the handlebar grip but DO
NOT re-engage the Blade Drive
Control. Drive the mower forward for
several more feet. Release the
Operator Presence Control and look
at the lawn. The grass should NOT
have been cut. This indicates that the
Operator Presence Control has disen-
gaged the blade drive and stopped
the blades.
If the Operator Presence Control or the
Blade Drive Control are not adjusted
correctly, the blades may continue to
rotate after release of the Operator
Presence Control. If the blades do not
stop within three (3) seconds of release
of the Operator Presence Control, move
the Engine Throttle Control to the STOP
position, disconnect the spark plug
wire, and move the wire away from the
spark plug. Do not operate the mower
until the Blade Brake Control System
has been repaired.
7. If the mower cuts the grass in Step
6-B, the Operator Presence Control is
NOT disengaging the blade drive.
Immediately stop the engine, discon-
nect the spark plug wire, and move the
wire away from the spark plug.
Failure to do this could result in per-
sonal injury or property damage.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Se5ction
Maintenance
Carefully read this Section on mower
and engine maintenance and service.
Performing the required maintenance ac-
cording to schedule will ensure the
proper performance and long life of your
machine.
OIL TYPE: Use clean, high quality deter-
gent oil having an A.P.I. service classifi-
cation of SE, SF or SG. Use no special
additives with oil. Refer to the Engine
Owner’s Manual for recommended SAE
viscosity grades that match the starting
temperature anticipated before the next
oil change.
5. Twist oil drain fixture (C) to the open
position. Pull out. Drain oil completely.
6. Push in and twist oil drain fixture to
the closed position. Remove drain hose.
Replace protective cap (A).
7. Refill engine with fresh oil and se-
curely replace dipstick.
WARNING
NOTE: Please dispose of all waste mate-
rials in an ecologically responsible man-
ner. Use proper waste material storage
containers.
Before inspecting, cleaning or servicing
the machine, shut off engine, make
sure that all moving parts have come to
a complete stop, disconnect spark plug
wire and move wire away from spark
plug. Remove ignition key on electric
start models.
Checking Oil Level:
1. Park machine on level ground.
2. Stop engine, wait for parts to stop
moving, and disconnect spark plug
wire.
3. Clean area around dipstick (Z, Figure
5-1) to prevent dirt from entering oil fill
hole.
Failure to follow these instructions can
result in personal injury or property
damage.
Z
4. Remove dipstick. Oil level must be be-
tween “ADD” and “FULL” marks. Do not
exceed “FULL” mark on dipstick.
NOTE: All references to left, right, front
and rear of the machine are determined by
standing behind the handlebars and facing
the direction of forward travel.
Figure 5-1: Briggs and Stratton engine oil
fill.
5. To add oil, pour slowly into dipstick
opening. While adding, check oil level
frequently by securely replacing dipstick
and removing to read oil level. Wipe dip-
stick clean each time oil level is checked.
IMPORTANT: REFER TO MAINTENANCE
CHART IN THIS SECTION FOR A LIST-
ING OF REGULARLY SCHEDULED
MAINTENANCE PROCEDURES.
C
A
6. After filling to “FULL” mark, securely
replace dipstick.
B
D
Changing Oil:
ENGINE SERVICE
Change oil while engine is still warm
from recent operation. Warm oil flows
more freely and carries away more im-
purities.
Routine engine service is described
below. For more complete engine ser-
vice information, refer to the engine
manual provided with your machine. For
complete engine service, contact an au-
thorized engine dealer.
Figure 5-2: Oil drain.
1. Stop engine, wait for parts to stop
moving, and disconnect spark plug
wire.
ENGINE OIL
2. Remove dipstick (Z, Figure 5-1).
OIL LEVEL: With mower on level ground,
the engine oil level must be between the
"ADD" and "FULL" marks on the dipstick
at all times. Check before each use and
every 5 operating hours.
3. Remove protective cap (A, Figure 5-
2) to expose oil drain port (B).
4. Push oil drain hose (D) (included in
hardware bag with unit) onto oil drain
port. Route other end of hose to an ap-
propriate oil collection receptacle.
OIL CHANGE: On a new engine, change
oil after first 2 hours of use, then change
oil regularly as specified on the
Maintenance Chart. Refer to Engine
Owner's Manual for oil capacity.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
ENGINE CLEANING
BATTERY (if applicable)
• Stop engine, wait for parts to stop
moving, disconnect spark plug wire,
and allow engine to cool before in-
specting or cleaning engine.
WARNING
D
Charge battery only with charger sup-
plied with machine. Do not short circuit
battery wires. Remove any jewelry be-
fore working on or near the battery or
electric start system. Failure to follow
these instructions could result in per-
sonal injury or property damage.
E
• Daily or more often, before running en-
gine, remove grass and chaff from recoil
finger guard or rotating screen to prevent
engine damage caused by overheating.
Also keep cooling vanes, governor link-
age, springs and controls free of debris.
B
A
Figure 5-3: Briggs and Stratton air cleaner
assembly.
• Daily or more often, before running en-
gine, clean muffler area (be sure muffler
is cool) to remove all grass and com-
bustible debris. If engine is equipped
with a spark arrestor screen, remove as-
sembly every 50 hours for cleaning and
inspection. Replace if damaged.
Charge battery if unit is to be stored for
longer than three weeks. During the
mowing season, the battery is kept
charged by the charging system on the
engine.
detergent and warm water. Squeeze dry
in a clean cloth.
4. Saturate foam pre-cleaner in clean en-
gine oil. Wrap in clean, absorbent cloth
and squeeze to remove all excess oil.
To Charge Battery:
1. Plug charger connector into wire har-
ness connector located below ignition
switch in handlebar console.
• Grass or chaff may clog engine's air
cooling system, especially after pro-
longed operation cutting tall, dry grass.
See Engine Owner's Manual for instruc-
tions on cleaning underneath the engine
blower housing.
5. Replace paper cartridge (B), if
necessary.
6. Reassemble air cleaner components.
Tighten knobs/screws (D) securely.
Secure cover assembly (E) on air cleaner
body.
2. Plug charger into 120V wall outlet.
(Note that battery charger is designed for
use indoors and should not be exposed to
rain or snow.)
AIR CLEANER SERVICE
SPARK PLUG
3. Charge battery for 24-48 hours if unit
is to be stored for longer than three
weeks.
Improper air cleaner maintenance can
cause engine damage. Refer to the
Engine Owner's Manual for more com-
plete air cleaner service information.
Inspect the spark plug (Figure 5-4) after
every 100 hours of operation. Be sure
the gap is set at .030". Do not reuse plug
if it is severely worn or damaged.
4. After charging, unplug charger from
outlet, then unplug charger from con-
nector on wire harness located below
handlebar console.
SERVICE SCHEDULE:
Best results are obtained with a new
plug. See Engine Owner's Manual to de-
termine proper replacement plug. Use of
incorrect plug can cause engine damage.
Outer foam pre-cleaner - wash and re-oil
every 25 operating hours or every sea-
son, whichever occurs first.
CARBURETOR
Inner paper cartridge - clean or replace
every 100 operating hours or every sea-
son, whichever occurs first.
The carburetor is adjusted at the factory.
It should not need to be reset. If black
exhaust is noted, check the air cleaner
first. An over-rich mixture is usually
caused by a poorly serviced or clogged
air cleaner element, not an improperly
adjusted carburetor. If readjustment is
necessary, refer to Engine Owner's
Manual or contact your local authorized
dealer.
NOTE: Do not clean spark plug in ma-
chines which use abrasive grit. Clean
spark plug by scraping or wire brushing,
or washing with a commercial solvent.
To Service Air Cleaner (Figure 5-3):
1. Stop engine, wait for parts to stop
moving, and disconnect spark plug
wire.
2. Unscrew mounting screws and/or re-
move knobs (D). Remove covers (E).
Remove paper cartridge (B) and foam
pre-cleaner (A). Separate foam pre-
cleaner from paper cartridge.
.030" Feeler Gauge
Figure 5-4: Spark plug.
3. Wash foam pre-cleaner (A) in liquid
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
The belt cover must be removed to per-
form several maintenance procedures.
5. Loosen four mounting bolts (L) se-
curing spindle housing (beneath mower
deck) to mower deck.
ENGINE STORAGE
If engine will be unused for 30 days or
more, prepare it for storage by following
the recommended procedures found in
the Engine Owner’s Manual.
To Remove Belt Cover:
6. Slide spindle housing (with pulley at-
tached) toward center.
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
7. Replace belt (N) with new belt.
IMPORTANT: SET BLADES PERPEN-
DICULAR (90°) TO EACH OTHER.
MOWER SERVICE
2. Remove four screws (R, Figure 5-5)
and remove cover.
The following maintenance/repair proce-
dures can be performed by either the
owner or an authorized service dealer.
See an authorized service dealer for
complete mower service.
8. Rotate arm (K) to move spindle
housing and apply tension to belt. Belt
cogs and pulley grooves must mesh to-
gether. When applying moderate finger
tension (8-12 lbs.), belt should deflect
approximately 1/2” (12.7 mm) at (P),
midpoint of deck.
To Reinstall Belt Cover:
1. Position belt cover in place.
2. Secure with the four screws removed
earlier.
TIPPING MOWER FOR SERVICE
WARNING
9. Tighten bolts (L) to 15 ft.-lbs. (20.3
Before servicing underside of mower,
stop engine, wait for all parts to stop
moving, and disconnect spark plug
wire. Remove ignition key from
keyswitch on electric start models.
Failure to follow this instruction could
result in personal injury or property
damage.
Nm). Tighten screw (J).
10. Blades must not contact deck.
Check and readjust as needed.
11. Reinstall blade drive belt and belt
cover (removed earlier).
R
FRONT
P
N
O
L
J
When servicing the underside of the
mower for any reason, the mower
should only be tipped backward on its
rear wheels (and securely propped up to
prevent it from falling). Tipping the
mower forward or to either side could
result in damage to engine.
Figure 5-5: Belt cover removal.
M
BLADE SPINDLE BELT
REPLACEMENT
Follow this procedure to remove and re-
place the blade spindle drive belt (re-
move blade drive belt first; see “Blade
Drive Belt Replacement” in this
Section).
K
BLADES
MUST BE PERPENDICULAR
TO EACH OTHER
TIP: Before tipping mower, install a
small plastic sandwich style bag under
the gas cap and tighten securely. This
will virtually eliminate any fuel weepage
from the cap. Be sure to remove the
plastic bag before re-using mower.
Figure 5-6: Blade Spindle Belt.
1. Stop engine, wait for all parts to
stop moving and disconnect spark plug
wire.
2. Remove belt cover (see “Belt Cover
Removal”).
BELT COVER REMOVAL
3. Align sight holes (O, Figure 5-6) in
pulley with spindle housing-to-mower
deck mounting bolts (L).
WARNING
Do not operate unit without belt cover
installed. Failure to follow this instruc-
tion could result in personal injury or
property damage.
4. Loosen screw (J) and rotate arm (K)
to the rear.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
BLADE DRIVE BELT
Blade Drive Disengaged
REPLACEMENT
Follow this procedure to remove and re-
place the blade drive belt. An assistant
will be needed.
A
To Remove Belt:
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
Blade Drive Engaged
2. Disengage blade drive control (Figure
5-7) by releasing all controls on the
mower.
RIGHT VIEW
Figure 5-7: Blade Drive Control.
3. Remove belt cover (see “Belt Cover
Removal”).
4. Loosen belt guides (B and C,
Figure 5-8).
5. Move flap bracket (N, Figure 5-8) out
of the way by loosening two screws (M).
B
6. Remove belt (A, Figure 5-8) from
around sheaves.
J
G
To Install Belt:
H
X
1. Route belt (A, Figure 5-8) around
sheaves as shown.
2. Have an assistant hold down Operator
Presence Control and then push the
Blade Drive Control forward until it
latches in place (Figure 5-7).
K
I
C
L
3. With the Blade Drive Control lever en-
gaged, adjust and tighten belt guide (B)
to 1/32 - 1/16" away from tensioned belt.
(Be sure that belt does not contact belt
guide when belt is under tension.)
Secure belt guide (C) rotated into posi-
tion as shown in Figure 5-8.
4. Disengage Blade Drive Control.
5. Re-tighten two screws (M, Figure
5-8) that secure flap bracket (N).
A
6. Reinstall belt cover securely.
N
M
M
Figure 5-8: Blade drive.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
BLADE BRAKE REPLACEMENT
Follow this procedure to install a new
blade brake.
Adjust idler in direction
of arrow to tighten blade
drive belt
To Remove Blade Brake:
D
F
J
1/8"
E
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
2. Remove belt cover as described in
“Belt Cover Removal” instructions.
3. Remove hardware (G, Figure 5-8)
securing blade brake (H).
4. Remove old brake (H) from idler
arm (I).
Figure 5-9: Blade drive adjustment.
To Install Brake:
1. Position new brake (H) in place on
idler arm (I).
6. Test the operation of the blade brake
(see “Blade Brake Control Test” in the
Operation section).
sure the Operator Presence Control
latches (A and B, Fig. 5-10) are fully
engaged at point (C). If they are not fully
engaged, improper operation or prema-
ture wear could result. To adjust, loosen
hex nut (D) and shorten length of control
rod (E). To avoid over-adjusting, turn
rod only 1 to 2 turns per adjustment.
2. Center brake in sheave groove and se-
cure brake (H) with hardware (G) re-
moved earlier.
7. If the drive belt slips during opera-
tion, it may be necessary to relocate idler
(J, Figure 5-9) in the slot provided in the
mounting bracket. With the engine
stopped and the spark plug wire dis-
connected, loosen the hardware on the
idler (J) and slide it forward to take up
slack in the belt.
3. Reinstall belt cover securely.
4. Test operation of blade brake (see
“Blade Brake Control Test” in Operation
section).
3. Tighten hex nut securely after adjust-
ing control rod.
4. Test by releasing the Operator
Presence Control. If properly adjusted,
the Blade Drive Control will disengage
when the Operator Presence Control is
released. Re-adjust as necessary by
repeating Steps 2 and 3.
BLADE DRIVE BELT
ADJUSTMENT
If the blade drive belt is slipping due to
lack of belt tension, follow the steps
below.
8. Engage the blade drive and measure
the distance (X, Figure 5-8) between the
centers of pulleys (K) and (L). The dis-
tance should be 5-1/2 to 5-5/8". After
obtaining the correct dimension, reinstall
the belt cover securely and test the oper-
ation of the blade brake.
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
C
BLADE DRIVE CONTROL LEVER
ADJUSTMENT
2. Remove belt cover as described in
“Belt Cover Removal” instructions.
A
E
Make the following adjustment if the
Blade Drive Control Lever releases dur-
ing operation.
3. With mower on level ground, adjust
blade cutting height at about 3" (measure
from ground to flat portion of blade).
B
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
4. With the Blade Drive Control (Figure
5-7) in the disengaged position, set a
gap of 1/8" between the spring (F, Figure
5-9) and flat washer (E) by adjusting the
nut (D).
2. Engage the Operator Presence Control
and the Blade Drive Control. Without re-
leasing the controls, look inside the
D
5. Reinstall the belt cover securely.
cutout at the rear of the frame and make
Figure 5-10: Blade Drive Control Lever
adjustment.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
WHEEL DRIVE BELT
REPLACEMENT
Follow this procedure to replace the
wheel drive belt.
1. Stop engine, wait for all parts to
Q
O
stop moving, and disconnect spark
plug wire.
2. Release all mower controls.
S
3. Remove belt cover as described in
“Belt Cover Removal” instructions.
P
4. Locate wheel drive belt (O, Figure 5-
11) and remove it from top sheave of en-
gine sheave, backsided idlers (P and Q)
and transmission sheave (R).
5. Install new belt as shown in Figure 5-
R
11. Belt must be installed “inside out ”–
“V” side of belt lies against
engine sheave only. Flat side of belt lies
against transmission sheave (R) and
back-sided idlers (P and Q).
Figure 5-11: Wheel drive belt replacement.
6. Make sure belt is inside belt guide (S,
Figure 5-11).
7. Reinstall belt cover securely.
8. An adjustment to the drive belt may
be necessary. See “Wheel Drive Belt
Adjustment” in this Section.
gage wheel drive by squeezing Wheel
Drive Control until it contacts handlebar.
4. Wheels should slip on paved surface.
If they do not, an adjustment is required.
To Adjust Wheel Drive Belt:
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
WHEEL DRIVE BELT
ADJUSTMENT
2. Remove cotter pin (A, Figure 5-12A)
from upper end of Wheel Drive Control
rod. Slide rod out of lever assembly.
The wheel drive belt requires an adjust-
ment if loss of drive belt tension (slip-
page) occurs. This is most noticeable
when more traction is required (such as
going up slopes).
A
3. Loosen jam nut (D, Figure 5-12).
4. Thread rod (E, Figure 5-12) one or
two turns clockwise for more tension or
counterclockwise for less tension.
5. Insert rod back into hole in Wheel
Drive Control lever and install cotter pin.
Bend ends of cotter pin to secure.
6. Retest wheel traction. Repeat adjust-
ment procedure, if necessary. Most
comfortable operation will be obtained
when the adjustment allows the lever to
just make contact with the handgrip as
sufficient wheel traction is achieved.
When adjustment is complete, tighten
jam nut (D) firmly against block (B).
Figure 5-12A
To Test Wheel Traction:
1. Park machine on a paved (concrete,
etc.) surface with front edge up against a
sturdy wall, fence, etc.
WHEEL BRAKE ADJUSTMENT
This adjustment may be required if the
machine does not hold on a hill with the
Operator Presence Control disengaged,
or if the brake drags with the Operator
Presence Control engaged and the trans-
mission in neutral.
2. Put Gear Select Lever in No. 1 setting.
IMPORTANT: DO NOT PARK AGAINST A
PAINTED OR SIDED WALL. TESTING
THE WHEEL DRIVE SYSTEM REQUIRES
MACHINE TO BE FORCIBLY PUSHED
AGAINST WALL. DAMAGE TO PAINT OR
SIDING COULD RESULT.
3. With engine running, and machine
placed firmly up against wall, hold down
Operator Presence Control and fully en-
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
2. Disengage (release) the Operator
Presence Control (M, Figure 5-13).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
5-15) clockwise until it stops in the neu-
tral (N) position (from forward gear
positions).
3. Hold down Operator Presence Control
(M, Figure 5-13) and push unit forward
and backward. Unit should move freely.
If not, continue with Step 4.
4. Remove cotter pin securing shift link
(P, Figure 5-15) to shift rod (I).
5. Move shift arm (X) back and forth as
necessary into each detent until trans-
mission is in neutral. NOTE: Moving
shift arm (X) clockwise all the way to the
left, and then one notch back counter-
clockwise, should put transmission into
neutral. When transmission is in neutral,
unit will move freely when pushed while
holding the Operator Presence Control
lever down. If transmission is NOT in
neutral, there will be a slight drag on the
wheels when pushing unit.
E
D
B
Figure 5-12: Wheel drive belt adjustment.
M
6. When shift arm (X) is in neutral posi-
tion, rotate shift link (P) until hooked
end fits back into hole in bottom end of
shift rod (I). NOTE: Shift rod (I) must be
held in the neutral position (see Figure
5-14) while shift link (P) is adjusted.
7. Secure shift link (P) into shift rod (I)
with cotter pin removed earlier.
N
8. Re-check neutral by pushing unit
back and forth and shifting lever (I) from
reverse to neutral. A small fine-tune
adjustment may be required.
P
O
N
3/8"-
5/16"
I
O
Figure 5-13: Wheel brake adjustment.
3. Slowly adjust at nut (O), if necessary,
until the distance between the back of
brake arm (N) and bracket (P) is 3/8”-
5/16". Use small adjustments (1/4 turn
maximum). NOTE: It may be necessary
to relieve spring tension when decreas-
ing distance. To do so, have an assis-
tant engage the Operator Presence
Control while you adjust the nut.
TRANSMISSION NEUTRAL
ADJUSTMENT
Follow this procedure to adjust neutral
on the transmission.
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
Detent for
Neutral Position
Figure 5-14: Lever in neutral (N) position.
2. Rotate shift rod (I, Figures 5-14 and
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
I
Y
Replace if separation
begins to form.
X
P
Figure 5-15: Transmission neutral (N) adjustment.
Sharpen blade cutting edge straight
across, parallel to blade trailing edge.
MOWER BLADES
To Sharpen Blades:
Grind or file the same amount from each
blade end to maintain blade balance. An
unbalanced mower blade produces ex-
cessive vibration and may damage spin-
dle bearings. Sharpen cutting edge
straight across, parallel to rear edge of
mower blade. See Figure 5-16. After
sharpening, blade balance must be
checked.
Figure 5-16: Blade Inspection
WARNING
Mower blades are sharp.
FRONT
• When working near blades, wear
heavy leather gloves or wrap blades in
thick rags to protect yourself from the
sharp edges.
• Wear eye protection when sharpening
blades.
IMPORTANT: PROFESSIONAL SHARP-
ENING SERVICES OR YOUR AUTHO-
RIZED DEALER ARE EQUIPPED TO
SHARPEN MOWER BLADES SAFELY.
BLADES
MUST BE PERPENDICULAR
TO EACH OTHER
Examine mower blades before operation.
For efficient mowing, cutting edges of
blades should always be kept sharp.
Check for blade wear or damage. See
Figure 5-16. Replace a severely worn or
damaged blade with a new one.
Figure 5-17
To Install Blades:
Blades must be installed perpendicular
to each other (see Figure 5-17).
Torque to
35 Ft. Lbs.
Install mower blade as shown in Figure
5-18 with flat side down. Install washer
on bolt. Tighten bolts to a torque value
of 35 ft. lbs. (47 Nm).
To Inspect Blades:
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
NOTE: If top bolt is removed, reinstall
using LOCTITE #242 thread sealant.
Mower Blade
2. Tip mower on rear wheels by follow-
ing instructions “Tipping Mower For
Service” in this Section of Manual.
Washer
To Remove Blades:
Bolt
Torque to
35 Ft. Lbs.
Remove bolt (Figure 5-18) and
washer(s). Remove mower blade.
Figure 5-18: Blade spindle.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
CLEANING UNDERSIDE OF
MOWER DECK
OFF-SEASON STORAGE
WARNING
• Stop engine, wait for all parts to stop
moving, and disconnect spark plug
wire before performing any storage
procedures. Review the storage safety
rules in the Safety Section of this
Manual.
Never store machine with fuel in the
fuel tank inside a building where fumes
may reach an open flame or spark, or
where ignition sources are present
such as hot water and space heaters,
furnaces, clothes dryers, stoves, elec-
tric motors, etc.
WARNING
Mower blades are sharp.
When working near blades, wear heavy
leather gloves or wrap blades in thick
rags to protect yourself from the sharp
edges.
• If engine will be unused for 30 days or
more, prepare it for storage by following
the recommended procedures found in
the Engine Owner's Manual.
Frequently check, and clean if necessary,
the underside of the mower deck. Grass
build-up in this area can affect the cut-
ting performance. Before inspecting or
cleaning, make sure that the engine is
shut off and the spark plug wire is
• Inspect all parts for damage, breakage,
and wear. Tighten or replace fasteners.
Contact your local authorized dealer for
factory-approved replacement parts.
• Clean the exterior of the mower thor-
oughly and touch up all chipped or
scratched surfaces to prevent rust from
forming.
disconnected from the spark plug.
Inspection/Cleaning of Mower Deck:
1. Stop engine, wait for all parts to
stop moving, and disconnect spark
plug wire.
2. Tip mower on rear wheels by follow-
ing instructions "Tipping Mower For
Service" in this Section.
3. Use a plastic or metal scraper to
remove grass build-up from deck or
blades. If needed, spray with a garden
hose.
LUBRICATION
Oil and grease the mower according to
the recommendations listed in the
Lubrication Chart on the next page.
• Stop engine, wait for all parts to stop
moving, and disconnect spark plug
wire before performing any lubrication
procedures.
• The transmission has been factory
sealed and requires no lubrication. If a
leak should develop, contact your local
authorized dealer for service information.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
Lubrication Chart
ITEM
INTERVAL
First 2 hours
LUBRICATION TYPE
AMOUNT REQUIRED
Engine Crankcase
Change Oil
See Engine Manual
25-50 hours
Change Oil
Change oil more often
in extremely dirty or
dusty conditions.
(Lubrication Intervals Vary
with Operating Conditions
and Type of Oil Used)
Front Wheel Bearings
50 hours
Grease
Light Oil
Grease
1-3 Strokes*
A Few Drops
1-3 Strokes*
Control Linkages/Pivots
Transmission Output Shaft
25 hours
100 hours or Annually
* A hand-type grease gun is recommended.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
ATTENTION! This chart describes service guidelines only. It does not provide complete service information. Complete service
is available from your local White Outdoor Dealer. Before performing any of the maintenance procedures, refer to the appropri-
ate information contained in this Manual or the Engine Owner’s Manual for the correct safety precautions and maintenance
procedures.
Maintenance Chart
INTERVAL*
ITEM
SERVICE
Each use
Mower Blade
Loose or Missing Hardware
Belts
Engine Oil Level
Controls
Mulching Cover
As Required
Tighten or Replace
Check
Check
Check for Proper Operation
Check for Proper Cover Installation
1st 2 hours
25 hours
Engine Oil
Change
Engine Oil***
Change
Clean
Sharpen and Balance
Lube with Light Oil
Foam Air Filter****
Mower Blade(s)
Control Linkages and Pivots
50 hours
Annually or 100 hours
Monthly
Engine Oil***
Change
Blade Drive Belt Adjust
Engine Cooling Fins
Grease Fittings**
Adjust Tension
Clean
Grease
Air Filter Element****
Spark Plug
Transmission Output Shaft
Replace
Clean/Replace, Re-gap
Grease
Linkages
Belts
Adjust
Check/Replace, Adjust
Annually or 50 hours
Front Wheel Bearings
Grease
*Interval describes running time.
**A hand-type grease gun is recommended when greasing your
unit. High-pressure type grease guns could cause damage to fit-
tings/seals.
***Consult engine manual for more detailed engine service infor-
mation.
****Clean more often under dusty conditions or when airborne
debris is present. Replace air cleaner parts, if very dirty.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Section 5: Maintenance
WARNING Before inspecting, cleaning or servicing the unit, shut off engine, wait for all parts to come
to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition
key on electric start models. Failure to follow these instructions can result in serious personal injury or
property damage.
ATTENTION! This table describes service
guidelines only. It does not provide com-
plete service information. Complete service
Symptom
is available from your local White Outdoor
Dealer. Before performing any of the cor-
rections in this table, refer to the appropri-
ate information contained in this Manual or
the Engine Owner’s Manual for the correct
safety precautions and operating or mainte-
nance procedures.
Troubleshooting Chart
Possible cause
Engine malfunction (refer to engine manual).
Improperly adjusted drive linkage.
Dirty engine cooling fins or flywheel screen.
Faulty ignition.
• • • • •
• • •
•
• •
• • • • •
•
• • • • •
• • • •
• •
Faulty spark plug.
•
Empty fuel tank.
• •
• •
•
•
•
•
•
•
•
Battery or charging malfunction (if applicable).
Improperly adjusted or dirty carburetor.
Improper oil level.
•
• • • •
•
Dirty air cleaner element.
• • •
• • • •
Improperly adjusted choke (if applicable).
Transmission malfunction.
• •
• •
Improperly adjusted drive linkage.
Broken, loose or worn belt(s).
Dull blade(s).
• •
• • •
•
•
•
• • •
Throttle control out of adjustment.
Blade/brake system out of adjustment.
Blade(s) out of balance.
• •
•
• •
•
•
•
•
Loose hardware.
• •
28
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
For TWO YEARS from the date of retail purchase within the United States of America, its possessions
and
territories,
White
Outdoor
Products
Company
will,
at
its
option, repair or replace, for the original purchaser, free of charge, any part or parts found to be defective
in material or workmanship. This warranty covers units which have been operated and maintained in ac-
cordance with the operating instructions furnished with the unit, and which have not been subject to mis-
use, abuse, neglect, accident, improper maintenance or alteration.
NORMAL WEAR PARTS or components thereof are subject to separate terms as noted below in the “No
Fault Ninety Day Consumer Warranty” clause. Commercial use is subject to the terms listed above, and
is covered for a period of 90 days from the date of purchase.
TWO YEAR CONSUMER WARRANTY ON NORMAL WEAR PARTS WITH NINETY DAY NO FAULT
PROTECTION: All normal wear parts failures will be covered on this product for a period of 90 days re-
gardless of cause. After 90 days, but within the two year period, normal wear parts failures will be cov-
ered if caused by defects in materials or workmanship. Normal wear parts are defined as belts, blades,
blade adapters, grass bags, rider deck wheels, seats, snow thrower skid shoes, shave plates and tires.
HOW TO OBTAIN SERVICE: Warranty service is available, with proof of purchase, through your local au-
thorized service dealer. To locate the dealer in your area, please check the yellow pages or contact the
Customer Service Department of White Outdoor Products Company, P. O. Box 361131, Cleveland, Ohio
44136-0019. Phone (330) 225-8883. The return of a complete unit will not be accepted by the factory
unless prior written permission has been extended by the Service Department of White Outdoor Products
Company.
TRANSPORTATION CHARGES: Transportation charges for the movement of any power equipment unit
or attachment are the responsibility of the purchaser. Transportation charges for any parts submitted for
replacement under this warranty must be paid by the purchaser unless such return is requested by White
Outdoor Products Company.
UNITS EXPORTED OUT OF THE UNITED STATES: White Outdoor Products Company does not extend
any warranty for products sold or exported outside of the United States of America, its possessions and
territories, except those sold through White Outdoor Products Company’s authorized channels of export
distribution.
OTHER WARRANTIES:
1. The engine or component parts thereof carry separate warranties from their manufacturers. Please
refer to the applicable manufacturer’s warranty on these items.
2. Batteries are covered by a 90-day replacement warranty.
3. Log splitter pumps, valves and cylinders or component parts thereof are covered by a one year war-
ranty.
4. All other warranties, express or implied, including any implied warranty of merchantability or fitness for
a particular purpose, are hereby expressly disclaimed in their entirety.
5. The provisions as set forth in this warranty provide the sole and exclusive remedy of White Outdoor
Products Company’s obligations arising from the sales of its products. White Outdoor Products
Company will not be liable for incidental or consequential loss or damage.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited warranty gives you specific legal rights,
and you may also have other rights which vary from state to state. Certain disclaimers are not allowed in
some states and therefore they may not apply to you under all circumstances.
NOTE: This warranty does not cover set-up, routine maintenance items such as lubricants, filters, blade
sharpening and tune-ups, or adjustments such as brake adjustments. Nor does this warranty cover
normal deterioration of the exterior finish due to use or exposure.
Download from Www.Somanuals.com. All Manuals Search And Download.
|