Model No. WEBE08920
Serial No.
USER’S MANUAL
Write the serial number in the
space above for reference.
Serial Number Decal (under seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
direct assistance from our
factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The technicians on our customer
hot line will provide immediate
assistance, free of charge.
Patent Pending
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
CAUTION
Visit our website at
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manu-
al for future reference.
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the weight bench.
1. Read all instructions in this manual before
using the weight bench. Use the weight
bench only as described in this manual.
10. Always keep an equal amount of weight on
both ends of your barbell when you are
using it. When adding or removing weights,
always keep some weight on both ends of
the barbell to prevent the barbell from tip-
ping.
2. It is the responsibility of the owner to ensure
that all users of the weight bench are ade-
quately informed of all precautions.
11. Do not use a barbell that is longer than six
feet with the weight bench.
3. The weight bench is intended for home use
only. Do not use the weight bench in any
commercial, rental, or institutional setting.
12. When you are using the leg lever, place a
barbell with the same amount of weight on
the weight rests to balance the bench.
4. Use the weight bench only on a level surface.
Cover the floor beneath the weight bench to
protect the floor.
13. Always exercise with a partner. When you
are performing bench press exercises, your
partner should stand behind you to catch the
barbell if you cannot complete a repetition.
5. Make sure all parts are properly tightened
each time you use the weight bench. Replace
any worn parts immediately.
14. Always set both weight rests at the same
height. Make sure that the adjustment knobs
are inserted completely and tightened into
the uprights before beginning any exercise.
6. Keep children under 12 and pets away from
the weight bench at all times.
7. Keep hands and feet away from moving parts.
15. When adjusting the position of the backrest,
make sure the adjustment tube is securely
seated in the adjustment brackets.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. The weight bench is designed to support a
maximum user weight of 300 pounds. Do not
place more than 110 pounds, including the
barbell, on the weight rests. Do not place
more than 110 pounds on the lat tower. Do
not place more than 50 pounds on the leg
lever. Note: The weight bench does not
include a barbell or weights.
16. Always remove the curl post and lat tower
from the front leg before performing leg curls
with the leg lever.
17. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile WEIDER® 160
weight bench. The WEIDER® 160 weight bench is
designed to be used with your own weight set (not
included) to help you develop every major muscle
group of the body. Whether your goal is a shapely fig-
ure, dramatic increase in muscle size and strength, or
a healthier cardiovascular system, the WEIDER® 160
will help you achieve the specific results you want.
toll-free at 1-800-999-3756, Monday through Friday,
6 a.m. until 6 p.m. Mountain Time (excluding holidays).
To help us assist you, please note the product model
number and serial number before calling. The model
number is WEBE08920. The serial number can be
found on a decal attached to the weight bench (see
the front cover of this manual).
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
using the weight bench. If you have additional ques-
tions, please call our Customer Service Department
ASSEMBLED
DIMENSIONS:
Height: 77 in.
Width: 49 in.
Depth: 71 in.
Lat Bar
Weight
Rests
Curl Pad
Backrest
Lat Tower
Adjustment Tube
Weight Carriage
Leg Lever
Seat
Weight Tube
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
Make Things Easier for Yourself
This manual is designed to ensure that the
weight bench can be assembled successfully
by anyone. Most people find that by setting
aside plenty of time, assembly will go smoothly.
The following tools (not included) are required
for assembly:
• Two adjustable wrenches
• One rubber mallet
Before beginning assembly, carefully read the
following information and instructions:
• One standard screwdriver
• Assembly requires two people.
• One Phillips screwdriver
• For help identifying small parts, refer to the PART
IDENTIFICATION CHART.
• Lubricant, such as grease or petroleum jelly,
and soapy water.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• As you assemble the weight bench, make sure all
parts are oriented as shown in the drawings.
1.
1
Before assembling the weight bench, make
sure that you have read and understand the
information in the box above.
1
32
22
Press a 38mm Square Inner Cap (32) into the
end of the Bench Frame (1).
41
43
22
Attach the Bench Frame (1) to the Front Leg (2)
using two M8 x 55mm Bolts (22), two M8
Washers (41), and two M8 Nylon Locknuts (43).
Do not tighten the Locknuts yet.
41
2
2. Insert a 25mm x 50mm Inner Cap (24) into the
Left Base (3). Attach the Left Base to the Bench
Frame (1) using an M8 x 35mm Carriage Bolt
(36), an M8 x 68mm Bolt (28), and two M8 Nylon
Locknuts (43). Do not tighten the Nylon
Locknuts yet.
2
Nuts
5
24
4
Attach the Left Upright (4) to the Left Base (3)
with two M8 x 35mm Carriage Bolts (36) and two
M8 Nylon Locknuts (43). Be sure the indicated
nuts are oriented as shown. Do not tighten the
Nylon Locknuts yet.
7
43
1
43
3
24
Repeat this step with the Right Base (7) and
the Right Upright (5).
28
36
36
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Attach the Storage Tube (51) to the Right Base
(7) with two M8 x 35mm Carriage Bolts (36) and
two M8 Nylon Locknuts (43).
3
Press a 45mm x 38mm Bushing (23) onto the
Left Upright (4). Slide a Weight Rest (6) into the
Upright and secure it at the desired height with a
54mm Adjustment Knob (27).
6
6
27
23
23
Secure the other Weight Rest (6) to the Right
Upright (5) in the same manner. Be sure that
both Weight Rests are set at the same height.
51
43
27
43
5
4
36
7
4. Press two 38mm Square Inner Caps (32) into the
ends of the Leg Lever (9). Press two 25mm
Round Inner Caps (21) into the ends of the
weight tube.
4
33
9
Insert four 19mm Round Inner Caps (47) into the
ends of two Pad Tubes (48). Slide the Pad Tubes
into the holes at the ends of the Leg Lever (9).
Slide four Foam Pads (33) onto the ends of the
Pad Tubes.
21
47
32
33
48
47
33
21
32
47
Weight
Tube
48
47
33
5. Lubricate the M10 x 67mm Bolt (46). Attach the
Leg Lever (9) to the Front Leg (2) using the Bolt
and an M10 Nylon Locknut (45). Do not over-
tighten the Nylon Locknut; the Leg Lever
must be able to pivot easily.
5
47
48
33
Press two 19mm Round Inner Caps (47) into the
ends of a Pad Tube (48). Slide the Pad Tube
through the hole in the Front Leg (2). Slide a
Foam Pad (33) onto each end of the Pad Tube.
45
9
2
47
Lubricate
46
33
6
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Press four 25mm Square Inner Caps (39) into the
ends of the Backrest Tubes (20). Be sure the
Caps are oriented as shown.
6
Attach the Backrest (15) to the Backrest Tubes
(20) using four M6 x 38mm Screws (14) and four
M6 Washers (31). Be sure the narrow end of
the Backrest is on the end shown. Do not
tighten the Screws yet.
Narrow
End
15
39
31
31
14
14
31
14
20
31
14
39
7. Press two 25mm Square Inner Caps (39) into the
Adjustment Tube (37). With the pins on the
Adjustment Tube facing downward, slide the
Adjustment Tube into a set of adjustment brack-
ets on the Uprights (4, 5).
7
39
37
Lubricate an M10 x 168mm Bolt (40). Attach the
Backrest Tubes (20) to the Bench Frame (1) with
the Bolt, two M10 Washers (29), and an M10
Nylon Locknut (45). Do not overtighten the
Nylon Locknut; the Backrest Tubes must be
able to pivot freely.
39
45
Tighten the M8 Nylon Locknuts (43) used in
step 2, and the four M6 x 38mm Screws (14)
used in step 6.
29
5
20
29
4
40
Bracket
1
Lubricate
8. Attach the Seat (16) to the Bench Frame (1)
using two M6 x 16mm Screws (10), an M6 x
50mm Screw (38), and an M6 Washer (31).
8
16
1
31
38
10
7
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Press two 25mm Round Inner Caps (21) into the
weight tube of the Weight Carriage (12). Press
two 45mm x 38mm Outer Bushings (23) onto the
top and bottom of the Weight Carriage.
9
Slot
25
Insert an M8 x 16mm Bolt (44) into the bracket on
the Weight Carriage (12). Slide the Weight
Carriage onto the Lat Tower (11) as shown.
11
23
44
Bracket
12
Route the Cable (25) through the slot of the Lat
Tower (11) in the indicated direction. Connect the
eyelet on the Cable to the Weight Carriage (12)
using the M8 x 16mm Bolt (44) and an M8 Nylon
Locknut (43).
21
43
21
Weight
Tube
23
10. Press a 38mm Square Inner Cap (32) into the top
of the Lat Tower (11).
10
32
42
29
45
26
Route the Cable (25) around the Pulley (26) as
indicated. Attach the Pulley inside the slot in the
Lat Tower (11) with an M10 x 55mm Bolt (49), two
M10 Washers (29), two M10 Spacers (42), and
an M10 Nylon Locknut (45). Do not overtighten
the Nylon Locknut; the Pulley must be able to
turn freely.
42
29
49
25
11
35
Attach the Cable Clip (35) to the end of the Cable
(25).
11. Slide the Lat Tower (11) into the Front Leg (2).
Tighten it in place with the 44mm Adjustment
Knob (34).
11
34
11
2
12. Wet the ends of the Lat Bar (18) with soapy
water. Slide a Handgrip (19) onto each end of the
Lat Bar. Attach the Lat Bar to the Cable Clip (35)
and place it in the lat bar rest on the Lat Tower
(11).
12
19
18
19
Lat Bar
Rest
11
35
8
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Attach the Curl Pad (17) to the Curl Post (13)
using two M6 x 16mm Screws (10). The Curl
Post and the Lat Tower attach to the weight
bench in the same place. Instructions for
switching between the Curl Post and the Lat
Tower can be found in the following section.
13
10
17
13
14. Make sure all parts are properly tightened
before you use the weight bench.
ADJUSTMENTS
This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 12 for impor-
tant information on how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the weight bench is used. Replace any worn parts immediate-
ly. The weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.
ADJUSTING THE BACKREST
Brackets
5
The Backrest (15) can be set to three different posi-
tions: a level position, a decline position, and an
incline position.
To change the position of the Backrest (15), move the
Adjustment Tube (37) to a different set of adjustment
brackets on the Uprights (4, 5).
4
15
Make sure the Adjustment Tube (37) is securely
seated in the adjustment brackets.
37
ATTACHING THE LAT BAR TO THE LAT TOWER
To use the Lat Tower (11), attach the Lat Bar (18) to
the Cable (25) with a Cable Clip (35).
25
35
18
11
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING WEIGHTS TO THE WEIGHT CAR-
RIAGE AND LEG LEVER
Weight
Tube
To use the Lat Tower (11) or the Leg Lever (9), slide
the desired amount of weight (not included) onto the
indicated weight tubes. Secure the weights onto the
Weight Carriage (12) with the two Weight Clips (50).
11
12
50
9
WARNING:
Do not place more
than 50 pounds on the Leg Lever (9), or more
than 110 pounds on the Weight Carriage (12).
50
Weight
Tube
ADJUSTING THE WEIGHT RESTS
To change the height of the Weight Rests (6), first
remove your barbell (not included) from the
Weight Rests. Remove the 54mm Adjustment Knobs
(27) from both Uprights (4, 5). Position the Weight
Rests at the desired height and align the holes in the
Weight Rests and the Uprights. Secure the Weight
Rests with the Adjustment Knobs. Make sure that
you fully tighten the Adjustment Knobs.
6
6
5
27
4
WARNING:
The Adjustment Knob
(27) must be inserted through both the Weight
Rest (6) and the Upright (4, 5), and be firmly
tightened. Always set both Weight Rests at
the same height. Never tighten a Knob into an
Upright before inserting the Weight Rest.
ATTACHING THE CURL POST OR LAT TOWER
For some exercises, the Curl Post (13) must be
attached to the weight bench. Insert the Curl Post into
the Front Leg (2). Align the holes in the Front Leg and
the Curl Post and secure the Curl Post with the
44mm Adjustment Knob (34). Make sure that you
fully tighten the Knob.
11
For other exercises, the Lat Tower (11) must be
attached to the weight bench. Insert the Lat Tower
into the Front Leg (2). Align the holes in the Front Leg
and the Lat Tower and secure the Lat Tower with the
44mm Adjustment Knob (34). Make sure that you
fully tighten the Adjustment Knob.
13
34
2
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STORING THE CURL PAD
When the Curl Pad (17) is not in use, it can be stored
in the Storage Tube (51). However, for some exercis-
es, the Curl Pad should be stored away from the
weight bench so it does not interfere with the exer-
cise.
17
51
FOLDING THE BACKREST
To perform squat exercises, you will need to fold the
Backrest (15) to the upright position.
6
To fold the Backrest (15), lift and pull it forward as far
as it will go. It will be held in place by its own weight.
6
WARNING:
Always fold the
Backrest (15) out of the way when performing
squat exercises. Do not sit on the Seat (16)
when the Backrest is folded.
16
Always place 50 pounds on the Leg Lever (9)
to balance the weight bench when performing
squat exercises.
15
Do not stand with your back to the weight
bench when performing squat exercises. You
should be able to see the Weight Rests (6)
while exercising so that you can safely return
the barbell when you finish the exercise.
9
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
PERSONALIZING YOUR EXERCISE PROGRAM
Muscle Building
Determining the exact length of time for each workout,
as well as the number of repetitions or sets complet-
ed, is an individual matter. It is important to avoid
overdoing it during the first few months of your exer-
cise program. You should progress at your own pace
and be sensitive to your body’s signals. If you experi-
ence pain or dizziness at any time while exercising,
stop immediately and begin cooling down. Find out
what is wrong before continuing. Remember that ade-
quate rest and a proper diet are important factors in
any exercise program.
To increase the size and strength of your muscles,
push them close to their maximum capacity. Your
muscles will continually adapt and grow as you pro-
gressively increase the intensity of your exercise. You
can adjust the intensity level of an individual exercise
in two ways:
• by changing the amount of weight used
• by changing the number of repetitions or sets per-
formed. (A “repetition” is one complete cycle of an
exercise, such as one sit-up. A “set” is a series of
repetitions.)
WARMING UP
The proper amount of weight for each exercise
depends upon the individual user. You must gauge
your limits and select the amount of weight that is
right for you. Begin with 3 sets of 8 repetitions for
each exercise you perform. Rest for 3 minutes after
each set. When you can complete 3 sets of 12 repeti-
tions without difficulty, increase the amount of weight.
Begin each workout with 5 to 10 minutes of stretching
and light exercise to warm up. Warming up prepares
your body for more strenuous exercise by increasing
circulation, raising your body temperature and deliver-
ing more oxygen to your muscles.
WORKING OUT
Toning
You can tone your muscles by pushing them to a
moderate percentage of their capacity. Select a mod-
erate amount of weight and increase the number of
repetitions in each set. Complete as many sets of 15
to 20 repetitions as possible without discomfort. Rest
for 1 minute after each set. Work your muscles by
completing more sets rather than by using high
amounts of weight.
Each workout should include 6 to 10 different exercis-
es. Select exercises for every major muscle group,
emphasizing areas that you want to develop most. To
give balance and variety to your workouts, vary the
exercises from session to session.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be
followed by at least one day of rest. Once you find the
schedule that is right for you, stick with it.
Weight Loss
To lose weight, use a low amount of weight and
increase the number of repetitions in each set.
Exercise for 20 to 30 minutes, resting for a maximum
of 30 seconds between sets.
EXERCISE FORM
Maintaining proper form is an essential part of an
effective exercise program. This requires moving
through the full range of motion for each exercise,
and moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you
feeling exhausted. On the exercise guide accompany-
ing this manual you will find photographs showing the
correct form for several exercises, and a list of the
muscles affected. Refer to the muscle chart on page
13 to find the names of the muscles.
Cross Training
Cross training is an efficient way to get a complete
and well-balanced fitness program. An example of a
balanced program is:
• Plan weight training workouts on Monday,
Wednesday, and Friday.
• Plan 20 to 30 minutes of aerobic exercise, such as
cycling or swimming, on Tuesday and Thursday.
• Rest from both weight training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
The repetitions in each set should be performed
smoothly and without pausing. The exertion stage of
each repetition should last about half as long as the
return stage. Proper breathing is important. Exhale
during the exertion stage of each repetition and inhale
during the return stroke. Never hold your breath.
The combination of weight training and aerobic exer-
cise will reshape and strengthen your body, plus
develop your heart and lungs.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Rest for a short period of time after each set. The
ideal resting periods are:
• Rest for three minutes after each set for a muscle
building workout.
each stretch gradually and go only as far as you can
without strain. Stretching at the end of each workout
is an effective way to increase flexibility.
• Rest for one minute after each set for a toning work-
out.
STAYING MOTIVATED
• Rest for 30 seconds after each set for a weight loss
workout.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
For motivation, keep a record of each workout. The
chart on pages 14 and 15 of this manual can be pho-
tocopied and used to schedule and record your work-
outs. List the date, the exercises performed, the
weight used, and the numbers of sets and repetitions
completed. Record your weight and key body mea-
surements at the end of every month. Remember, the
key to achieving the greatest results is to make exer-
cise a regular and enjoyable part of your everyday
life.
COOLING DOWN
End each workout with 5 to 10 minutes of stretching.
Include stretches for both your arms and legs. Move
slowly as you stretch and do not bounce. Ease into
MUSCLE CHART
N
O
P
A. Sternomastoid (neck)
B. Pectoralis Major (chest)
C. Biceps (front of arm)
D. Obliques (waist)
A
B
E. Brachioradials (forearm)
F. Hip Flexors (upper thigh)
G. Abductor (outer thigh)
H. Quadriceps (front of thigh)
I. Sartorius (front of thigh)
J. Tibialis Anterior (front of calf)
K. Soleus (front of calf)
C
D
E
Q
R
S
F
L
T
L. Rectus Abdominus (stomach)
M. Adductor (inner thigh)
G
M
N. Trapezius (upper back)
O. Rhomboideus (upper back)
P. Deltoid (shoulder)
H
I
U
V
Q. Triceps (back of arm)
J
K
W
R. Latissimus Dorsi (mid back)
S. Spinae Erectors (lower back)
T. Gluteus Medius (hip)
U. Gluteus Maximus (buttocks)
V. Hamstring (back of leg)
W. Gastrocnemius (back of calf)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE
WEIGHT
WEIGHT
WEIGHT
SETS
SETS
SETS
REPS
REPS
REPS
MONDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
TUESDAY
Date:
/
/
WEDNESDAY
Date:
/
/
AEROBIC EXERCISE
EXERCISE
THURSDAY
Date:
/
/
FRIDAY
Date:
/
/
Make photocopies of this page for scheduling and recording your workouts.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Monday
through Friday, 6 a.m. until 6 p.m. Mountain Time (excluding holidays). To help us assist you, please be pre-
pared to give the following information when calling:
• The MODEL NUMBER of the product (WEBE08920)
• The NAME of the product (WEIDER® 160 weight bench)
• The SERIAL NUMBER of the product (see the front cover of this manual)
• The KEY NUMBER and DESCRIPTION of the desired part(s) (see the PART LIST and the EXPLODED
DRAWING in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of ninety (90) days from the date of pur-
chase. This warranty extends only to the original purchaser. ICON's obligation under this warranty is lim-
ited to replacing or repairing, at ICON's option, the product through one of its authorized service centers.
All repairs for which warranty claims are made must be pre-authorized by ICON. This warranty does not
extend to any product or damage to a product caused by or attributable to freight damage, abuse, mis-
use, improper or abnormal usage or repairs not provided by an ICON authorized service center; products
used for commercial or rental purposes; or products used as store display models. No other warranty
beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 187091 R0702B
Printed in China © 2002 ICON Health & Fitness, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVE THIS PART IDENTIFICATION CHART
PART LIST/EXPLODED DRAWING
SAVE THIS PART IDENTIFICATION CHART
PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE
81
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
M10 Spacer (42)
M10 Nylon Locknut (45)
M10 Washer (29)
M8 Nylon Locknut (43)
M6 Washer (31)
M8 Washer (41)
M6 x 50mm Screw (38)
M8 x 55mm Bolt (22)
M6 x 16mm Screw (10)
M8 x 16mm Bolt (44)
M10 x 55mm Bolt (49)
M6 x 38mm Screw (14)
M10 x 67mm Bolt (46)
M8 x 68mm Bolt (28)
M8 x 35mm Carriage Bolt (36)
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. WEBE08920
R0702B
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
1
1
2
1
2
1
4
1
1
1
4
1
1
1
1
2
2
4
2
2
2
1
1
Bench Frame
Front Leg
Left Base
Left Upright
Right Upright
Weight Rest
Right Base
50mm x 45mm Outer Bushing
Leg Lever
M6 x 16mm Screw
Lat Tower
Weight Carriage
Curl Post
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
#
2
2
4
1
5
4
6
1
1
8
1
1
6
1
2
2
13
1
3
1
6
3
1
2
1
1
54mm Adjustment Knob
M8 x 68mm Bolt
M10 Washer
Storage Tube
M6 Washer
38mm Square Inner Cap
Foam Pad
44mm Adjustment Knob
Cable Clip
M8 x 35mm Carriage Bolt
Adjustment Tube
M6 x 50mm Screw
25mm Square Inner Cap
M10 x 168mm Bolt
M8 Washer
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
M6 x 38mm Screw
Backrest
Seat
Curl Pad
Lat Bar
M10 Spacer
M8 Nylon Locknut
M8 x 16mm Bolt
M10 Nylon Locknut
M10 x 67mm Bolt
19mm Round Inner Cap
Pad Tube
M10 x 55mm Bolt
Weight Clip
User’s Manual
Handgrip
Backrest Tube
25mm Round Inner Cap
M8 x 55mm Bolt
45mm x 38mm Outer Bushing
25mm x 50mm Inner Cap
Cable
Pulley
#
Exercise Guide
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING—Model No. WEBE08920
R0702B
32
39
17
45
29
19
37
10
42
42
29
39
18
13
26
49
19
25
35
6
11
16
8
6
34
27
30
15
5
43
43
27
25
43
8
23
44
24
39
43
39
31
14
36
29
21
12
4
43
14
39
20
29
21
45
31
31
14
23
43
7
36
22
43
40
32
43
1
36
33
43
45
41
31
38
10
47
10
43
24
46
2
22
47
43
21
9
41
48
28
36
32
36
47
33
3
33
47
50
21
48
48
47
32
33
47
Download from Www.Somanuals.com. All Manuals Search And Download.
|