THE SINGER'S ULTIMATE CHOICE
CDR-1000 PRO
Professional Single Rack CD Recorder and Player
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC INFORMATION (U.S.A.)
CAUTION:
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
READ THIS BEFORE OPERATING YOUR UNIT
UNIT!: This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Vocopro may void your authority, granted by the FCC,
to use this product.
1. To ensure the finest performance, please read this
manual carefully. Keep it in a safe place for future reference.
2. Install your unit in a cool, dry, clean place - away from
windows, heat sources, and too much vibration, dust,
moisture or cold. Avoid sources of hum (transformers, v
motors). To prevent fire or electrical shock, do not expose to
rain and water.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high
quality shielded cables. Cable(s) supplied with this
product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your
FCC authorization to use this product in the U.S.A.
3. Do not operate the unit upside-down.
3. NOTE: This product has been tested and found to
comply with the requirements listed in FCC Regulations,
Part 15 for Class "B" digital devices. Compliance with
these requirements provides a reasonable level of
assurances that your use of this product in a residential
environment will not result in harmful interference with
other electronic devices. This equipment
generates/uses radio frequencies and, if not installed
and used according to the instructions found in the
owner's manual, may cause interference harmful to the
operation of other electronic devices. Compliance with
FCC regulations does not guarantee that interference
will not occur in all installations. If this product is found
to be the source of interference, which can be
determined by turning the unit "Off" and "On", please try
to eliminate the problem by using one of the following
measures:
4. Never open the cabinet. If a foreign object drops into the
set, contact your dealer.
5. Place the unit in a location with adequate air circulation.
Do not interfere with its proper ventilation; this will cause the
internal temperature to rise and may result in a failure.
6. Do not use force on switches, knobs or cords. When
moving the unit, first turn the unit off. Then gently disconnect
the power plug and the cords connecting to other
equipment. Never pull the cord itself.
7. Do not attempt to clean the unit with chemical solvents:
this might damage the finish. Use a clean, dry cloth.
8. Be sure to read the "Troubleshooting" section on common
operating errors before concluding that your unit is faulty.
Relocate either this product or the device that is being
affected by the interference.
9. This unit consumes a fair amount of power even when the
power switch is turned off. We recommend that you unplug
the power cord from the wall outlet if the unit is not going to
be used for a long time. This will save electricity and help
prevent fire hazards. To disconnect the cord, pull it out by
grasping the plug. Never pull the cord itself.
Use power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter(s).
In the case of radio or TV interference, relocate/reorient
the antenna. If the antenna lead-in is 300-ohm ribbon
lead, change the lead-in to coaxial type cable.
10. To prevent lightning damage, pull out the power cord
and remove the antenna cable during an electrical storm.
If these corrective measures do not produce satisfactory
results, please contact your local retailer authorized to
distribute Vocopro products. If you can not locate the
appropriate retailer, please contact Vocopro, 1728
Curtiss Court, La Verne, CA 91750.
11. The general digital signals may interfere with other
equipment such as tuners or receivers. Move the system
farther away from such equipment if interference is
observed.
NOTE:
Please check the copyright laws in your country
before recording from records, compact discs,
radio, etc. Recording of copyrighted material may
infringe copyright laws.
CAUTION
The apparatus is not disconnected from the AC power
source so long as it is connected to the wall outlet,
even if the apparatus itself is turned off. To fully insure
that the apparatus is indeed fully void if residual power,
leave unit disconnected from the AC outlet for at least
fifteen seconds.
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome.
And Thank you for purchasing the CDR-1000 PRO from VocoPro, your ultimate choice
in Karaoke entertainment! With years of experience in the music entertainment
business, VocoPro is a leading manufacturer of Karaoke equipment, and has been
providing patrons of bars, churches, schools, clubs and individual consumers the
opportunity to sound like a star with full-scale club models, in-home systems and mobile
units. All our products offer solid performance and sound reliability, and to further
strengthen our commitment to customer satisfaction, we have customer service and
technical support professionals ready to assist you with your needs. We have provided
some contact information for you below.
VocoPro
1728 Curtiss Court
La Verne, CA 91750
Toll Free: 800-678-5348
TEL: 909-593-8893
FAX: 909-593-8890
VocoPro Company Email Directory
Customer Service & General Information
Tech Support
Remember Our Website
products, packages and promos. And while you’re there don’t forget to check out our
Club VocoPro for Karaoke news and events, chat rooms, club directories and even a
Service directory!
We look forward to hearing you sound like a PRO, with VocoPro, your ultimate choice in
Karaoke entertainment.
FOR YOUR RECORDS
Please record the model number and serial number below, for easy reference, in case of loss or theft. These
numbers are located on the rear panel of the unit. Space is also provided for other relevant information
Model Number
Serial Number
Date of Purchase
Place of Purchase
Download from Www.Somanuals.com. All Manuals Search And Download.
Listening For A Lifetime
Selecting fine audio equipment such as the unit you’ve just purchased is only the start of
your musical enjoyment. Now it’s time to consider how you can maximize the fun and
excitement your equipment offers. VocoPro and the Electronic Industries Association’s
Consumer Electronics Group want you to get the most out of your equipment by playing it
at a safe level. One that lets the sound come through loud and clear without annoying
blaring or distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to a higher volume
of sound. So what sounds “normal” can actually be loud and harmful to your hearing. Guard
against this by setting your equipment at a safe level BEFORE your hearing adapts.
To establish a safe level:
• Start your volume control at a low setting.
• Slowly increase the sound until you can hear it comfortably and clearly, and without
distortion.
Once you have established a comfortable sound level:
• Set the dial and leave it there.
• Pay attention to the different levels in various recordings.
Taking a minute to do this now will help to prevent hearing damage or loss in the future.
After all, we want you listening for a lifetime.
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since
hearing damage from loud noise is often undetectable until it is too late, this manufacturer
and the Electronic Industries Association’s Consumer Electronics Group recommend you
avoid prolonged exposure to excessive noise. This list of sound levels is included for your
protection.
Some common decibel ranges:
Level
Example
30
40
50
60
70
80
Quiet library, Soft whispers
Living room, Refrigerator, Bedroom away from traffic
Light traffic, Normal Conversation
Air Conditioner at 20 ft., Sewing machine
Vacuum cleaner, Hair dryer, Noisy Restaurant
Average city traffic, Garbage disposals, Alarm clock at 2 ft.
The following noises can be dangerous under constant exposure:
Level
Example
90
100
120
140
180
Subway, Motorcycle, Truck traffic, Lawn Mower
Garbage truck, Chainsaw, Pneumatics drill
Rock band concert in front of speakers
Gunshot blast, Jet plane
Rocket launching pad
-Information courtesy of the Deafness Research Foundation
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety instructions
FCC Information
Welcome
Listening For a Lifetime
Specifications and Features .............................................................. 1
Mounting ................................................................................................................... 2
Getting Connected ...................................................................... 3-5
Inputting Audio ..................................................................... 3
Switching Between Analog and Digital ....................................... 5
Outputting Audio ................................................................... 5
Controls and Functions ................................................................ 6-8
Front Panel .......................................................................... 6
Rear Panel ....................................................................... 7-8
Operations ............................................................................... 9-11
Choosing between Playback Mode and Record Mode ................. 9
Preparing a Disc for Playback ................................................. 9
Playing a Disc ...................................................................... 9
Recording on to a Disc......................................................... 10
Pausing Recording .............................................................. 10
Creating Tracks on a Disc .................................................... 10
Finalizing a Disc .................................................................. 11
Erasing a Disc .................................................................... 11
Troubleshooting ...................................................................... 12-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications and Features
Features
• Burn music to CD-R, CD-RW**, 8cm* CD-R and 8cm* CD-RW** live and in real-time without a computer
• Rackmount ready and requires only 1 RU of rackspace
• Simple “Finalizing” of CD-R/RWs
• Create CDs that can be played in standard CD players
• Erase data from CD-RW discs
• Digital Coaxial audio input (compatible with 44.1kHz)
• RCA and balanced XLR audio line in/out connections
• Headphone input so you can monitor your recording
• Create separate tracks while recording live
• Recording Volume control for pro sounding recordings
*The analog input does not support 8cm CD-R/RW discs. Use the digital input on the rear panel of the CDR-1000 PRO
when burning to an 8cm CD-R/RW disc.
** Most standard CD players (Car audio, home audio, etc.) do not support CD-RW discs. If using CD-RW discs, make sure
that your CD player specifies that it is CD-RW compatible.
Specifications
System .....................................................................Compact Disc Recordable
Playback format..........................................................CD
Recording formats......................................................CD-R, CD-RW, 8cm CD-R, 8cm CD-RW (Audio and Data discs)
Quantization...............................................................24-bit linear
Sampling Frequency ....................................................44.1 kHz
Frequency Response...................................................20 Hz – 20 kHz
Power Consumption....................................................32W
Accessories...............................................................Power Cord, RCA cable
Dimensions (WxHxD)...................................................17” x 1.8” x 12.7”
Weight......................................................................10.4 lbs
I/O Configuration
Analog Input
Connector .................................................................XLR 3-31 Type, RCA
Input Impedance.........................................................10k� (balanced), 10k�
Analog Output
Connector .................................................................XLR 3-32 Type, RCA
Output Impedance....................................................... 600� (balanced), 600�
Head Phone Output
Connector .................................................................¼” Stereo Jack
Load Impedance.........................................................32�
Maximum Output........................................................Level 300mW
Coaxial Input (IEC60958)
Connector .................................................................RCA
Input Impedance.........................................................75�
NOTE: Specifications are subject to change without prior notice.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Mounting
Use the included mounting brackets to mount the CDR-1000 PRO into a 19” rack case. The
CDR-1000 PRO requires 1 RU of available rackspace.
Installing the Mounting Brackets onto the CDR-1000 PRO
Position the mounting brackets on the CDR-1000 PRO with the tabs facing away from the player.
Line up the three holes on the mounting bracket with three holes on the sides of the CDR-1000
PRO. Use the included screws to secure the brackets on each side of the CDR-1000 PRO.
NOTE: You will need a screwdriver for securing the rack ears. (Screwdriver not included)
Mounting the CDR-1000 PRO Into a Rackcase
To mount, carefully place the CDR-1000 PRO in the rack space of your case. The CDR-1000
PRO takes 4 screws to mount. Make sure holes are aligned evenly. Use an alternating “X” rota-
tion when screwing to ensure even tension and alignment.
You will need:
• 19” Rack Case
• 4 Mounting Screws
• Phillips-head Screwdriver
1
3
4
2
3
1
2
4
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Connected
Connecting the Headphones
Using headphones with a ¼” connection, connect them to the HEADPHONE input jack on the
CDR-1000 PRO.
Inputting Audio
The CDR-1000 PRO can be easily integrated into your audio system for easy recording and
without compromising the overall sound quality. Refer to the instructions below when con-
necting your CDR-1000 PRO.
NOTE: There are three options for inputting audio to the CDR-1000 PRO:
• Balanced XLR (Analog)
• Unbalanced RCA (Analog)
• Digital Coaxial (Digital).
NOTE: The CDR-1000 PRO needs to be in ANALOG mode if using either XLR or RCA and in
DIGITAL mode when using the Digital Coaxial input.
1. Using Two Balanced XLR Cables and Connecting to the BALANCED XLR inputs
NOTE: The CDR-1000 PRO must be in ANALOG mode
1. Connect the “male” end of each cable to the BALANCED left and right inputs on the rear
panel of the CDR-1000 PRO.
2. Connect the “female” end of each cable to the left and right outputs of your player or mixer.
CDR-1000 PRO
OUTPUT
ANALOG i/O
INPUT
DIGITAL
INPUT
LEFT
RIGHT
LEFT
RIGHT
UNBAL
UNBAL
BAL UNBAL
BAL UNBAL
S/PDIF
LA VERNE, CALIFORNIA U.S.A.
GIG-MASTER
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Connected cont.
2. Using two RCA (red and white) Cables and Connecting to the UNBALANCED RCA inputs
NOTE: The CDR-1000 PRO must be in ANALOG mode
1. Connect an end of each cable to the UNBALANCED left and right inputs on the rear panel of the
CDR-1000 PRO.
2. Connect the other end of each cable to the left and right outputs of your player, mixer or amp.
CDR-1000 PRO
ANALOG i/O
INPUT
DIGITAL
INPUT
GHT
LEFT
RIGHT
UNBAL
BAL UNBAL
BAL UNBAL
S/PDIF
NOTE: Match up the colors of the RCA cables to the colors of the inputs.
White into white and red into red.
CDR-1000 PRO
DVX-880 PRO
ANALOG i/O
INPUT
DIGITAL
INPUT
D
V
X
-
8
8
0
P
R
O
M
U
LT
I
F
O
R
M
AT
K
A
R
A
O
K
E
P
L
AY
E
R
OPEN/CLOSE
GHT
LEFT
RIGHT
REPEAT
JPEG
CDG
P
H
O
T
O
C
D
DIGITAL KEY
CONTROL
DIGITAL
ECHO
PLAY/PAUSE
STOP
PREV
NEXT
UNBAL
BAL UNBAL
BAL UNBAL
S/PDIF
3. Connecting to the Digital Coaxial input (compatible with 44.1 kHz)
NOTE: The CDR-1000 PRO must be in DIGITAL mode
1. Using an RCA cable, connect one end to the Digital Input on the rear panel of the CDR-1000 PRO.
2. Connect the other end of the RCA cable to the digital (coaxial) output on your disc player.
CDR-1000 PRO
CDG-555k
OUTPUT
LEFT
ANALOG i/O
INPUT
DIGITAL
INPUT
DVG-555K
5
DISC KARAOKE MIXER/PLAYER
RIGHT
LEFT
RIGHT
DISC
1
DISC
2
DISC
3
DISC
4
DISC
5
ALL
R
CD+G
V
I
D
E
O
PAL/NTSC
L/R
DISPLAY
BAL UNBAL
BAL UNBAL
BAL UNBAL
BAL UNBAL
S/PDIF
POWER
LA VERNE, CALIFORNIA U.S.A.
VOL
1
VOL
2
ECHO
MIC BASS
MIC TREBLE
1
2
3
4
5
6
7
8
9
0
#
ON
/
OFF
MIC
1
MIC
2
0
10
0
10
0
10
-10
+10
-10
+10
NOTE: If your player does not have a digital output, you will not be able to use the
CDR-1000 PRO’s Digital Input.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Connected cont.
Switching between Analog and Digital
1. When in Playback Mode, press the source button on the front of the CDR-1000 PRO
2. There will be an “A” in the display screen when in Analog mode and a “D” when in Digital mode.
NOTE: You will not be able to switch between Analog and Digital modes while the CDR-1000 PRO is in
Record Mode.
ATTENTION: If you are burning onto an 8cm CD-R/RW, you must use the Digital input. The Analag
input does not support 8cm CD-R/RWs
CDR-1000 PRO
Outputting Audio
1. Using Two XLR Cables and Connecting to the BALANCED XLR inputs
1. Connect the “female” end of each cable to the BALANCED left and right XLR outputs on the rear
panel of the CDR-1000 PRO.
2. Connect the “male” end of each cable to the left and right XLR inputs of your mixer or amp.
2. Using two RCA (red and white) Cables and Connecting to the UNBALANCED RCA inputs
1. Connect one end of each cable to the UNBALANCED left and right RCA outputs on the rear panel of
the CDR-1000 PRO.
2. Connect the other end of each cable to the left and right RCA inputs of your player, mixer or
All-In-One system.
PKJ-9090PRO
PROFESSIONAL DJ/KJ/VJ POWERED MIXER
LIGHT
(DC 12V)
CROSSFADER
VIDEO TOGGLE
DSP KEY CONTROL AND
CROSSFADER VIDEO TOGGLE
CDR-1000 PRO
1 2 3 4
VIDEO
1
VIDEO
2
VIDEO
3
LEFT
AV
PH 1/LINE
CD
1
AV
PH 2/LINE
CD
2
AV
PH 3/LINE
CD
3
-26 -20 -17 -14 -10 -6
0
+3 +6 +9 +10 +15
ANALOG i/O
INPUT
DIGITAL
INPUT
RIGHT
1
2
3
OUTPUT LEVEL DISPLAY
STEREO
1
STEREO
2
STEREO
3
(BALANCED)
(BALANCED)
(BALANCED)
(BALANCED)
GHT
LEFT
RIGHT
POWER
SIGNAL
-20
+6
SIGNAL
-20
+6
SIGNAL
-20
+6
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
GAIN
AV OUT LEVEL
POWER AMP LEVEL
+12
VOCAL EFFECTS
HEADPHONES
MANUAL
+12
+12
+12
+12
PARTNER ELIMI. MULTI.
TREBLE
TREBLE
TREBLE
TREBLE
UNBAL
BAL UNBAL
BAL UNBAL
S/PDIF
-12
-12
-12
-12
-12
CROSSFADER
VOCAL
CUE
DOWN
NORMAL
CUE
UP
60
ON
250
1K
4K
12K
CUE
CUE
BASS
BASS
BASS
BASS
MASTER EQUALIZER
PHONES LEVEL
ON
ON
ON
MAST
ECHO
KEY
KEY
KEY
VIDEO SEL.
ECHO
ECHO
ECHO
ECHO
ON
ON
ON
ON
CUE
CUE
CUE
CUE
AUTO
OFF
ON
LEVEL
ON
ON
ON
ON
KEY
KEY
KEY
KEY
ON
ON
ON
ON
1
2
3
REPEAT
1
2
2
3
DELAY
ASSIGN
ASSIGN
CROSSFADER
/
VIDEO TOGGLE
MIC
1
MIC
2
MIC
3
MIC
4
TALK OVER
MASTER/LEFT
MASTER/RIGHT
BOOTH
DIGITAL ECHO
NOTE: Match up the colors of the RCA cables to the colors of the inputs.
White into white and red into red.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Functions
Front Panel Controls and Functions
1
2
3
4
5
6
7
1. DISC tray - Insert discs here. Open and close the disc tray using the EJECT button.
2. LED DISPLAY - Displays information regarding the CDR-1000 PRO’s operating status.
3. INPUT VOLUME meter - Displays the volume level that is being input for recording. Use the RECORD LEVEL
control to keep the volume from peaking or from being too low. The volume is peaking when the orange bars at
the top of the meter are lit. For best results, the meter should remain in the middle. Doing so should prevent
unwanted distortion, which is present when the recording level is too loud. If it is too low, the recording will be
difficult to hear when played back.
4. EJECT (**EJECT SYMBOL) button - This button is used to open and close the DISC tray.
5. PREV |<< button - This button is used to scan backwards through a track or to go back to a PREVIOUS track.
Press it once to skip to the beginning of the current track, twice quickly to jump to the previous track and hold it
down to scan backwards through the current track.
6. NEXT >>| button - This button is used to scan forwards through a track or to advance to the NEXT track.
Press it once to skip to the next track, and hold it down to scan forwards through the current track.
7. PLAY/PAUSE button - This button is used to begin playing a disc when it is not already playing. It will PAUSE
a disc that is already playing.
START recording (When in Record Mode) - Press this button while in Record Mode, to start recording.
See the Operations section of this manual for in-depth recording instructions.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Functions cont.
Front Panel Controls and Functions
8
9 10
11 12 13 14 15
8. STOP/CANCEL button - This button is used to STOP disc PLAYBACK.
CANCEL recording (When in Record Mode) - Press this button to stop recording.
9. RECORD (**RECORD symbol) button - Press this button to switch the CDR-1000 PRO to Record Mode.
Use this button to start a new track while the CDR-1000 PRO is already recording.
NOTE: Recording will not actually start until you press the START button.
10. POWER switch - Use this to turn the power on and off.
11. RECORD LEVEL control - Use this to adjust the volume level that is being recorded onto the disc.
NOTE: The record level control only adjusts music that is being input into the CDR-1000 PRO. It will not
control the volume of a disc that is being played in the CDR-1000 PRO’s disc player.
12. SOURCE button - Switches between Analog and Digital input mode. Select Analog when using the RCA or
XLR audio inputs and Digital when using the Digital (Coaxial) audio input.
NOTE: The analog input does not support 8cm CD-R/RW discs. Use the Digital input on the rear panel of the
CDR-1000 PRO when burning to an 8cm CD-R/RW disc and make sure it is in Digital input mode.
13. ERASE button - Use this button to erase data from a CD-Rewritable (CD-RW) disc.
NOTE: This function only works on CD-Rewritable (CD-RW) discs and will not work on CD-Rs.
14. FINALIZE button - Use this to finalize a disc. Finalizing a disc enables that disc to be played in any standard
disc player. I.e. Car stereo, home stereo. If a disc is not finalized, it can only be played in the CDR-1000 PRO’s
disc player.
15. HEADPHONE jack - Plug in your headphones here.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls and Functions
Rear Panel Controls and Functions
4
3
2
1
AC INPUT
OUTPUT
ANALOG i/O
INPUT
DIGITAL
INPUT
LEFT
RIGHT
LEFT
RIGHT
BAL UNBAL
BAL UNBAL
BAL UNBAL
BAL UNBAL
S/PDIF
LA VERNE, CALIFORNIA U.S.A.
~90V-24V~50/60HZ
5
6
1. BALANCED XLR inputs - Use these to input stereo audio using a pair of balanced XLR cables.
CDR-1000 PRO must be in Analog mode.
2. UNBALANCED RCA inputs - Use these to input stereo audio using Left and Right (red and white) RCA cables.
CDR-1000 PRO must be in Analog mode.
3. BALANCED XLR outputs - Use these to output stereo audio using a pair balanced XLR cables.
4. UNBALANCED RCA outputs - Use these to output stereo audio using Left and Right (red and white) RCA cables.
5. DIGITAL INPUT - Connect a player using a digital (coaxial) connection. CDR-1000 PRO must be in Digital mode.
Compatible with 44.1 kHz. digital signal.
6. AC IN terminal - Connect AC main power cord from the wall outlet to this terminal.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations
Choosing Playback Mode or Record Mode
When you first turn on the CDR-1000 PRO, it will be in Playback Mode. Before you can begin recording, it
must be in Record Mode. Press the RECORD button to enter into Record Mode and follow the operating
instructions in this manual. Press the CANCEL button to exit Record Mode and return to Playback Mode.
NOTE: Music from your audio input source cannot be heard when the CDG-1000 PRO is in Playback Mode.
CDR-1000 PRO
Preparing a Disc for Playback
Turn the power on by switching the POWER button on the front panel to the ON position. Press the EJECT
button on the front panel to open the disc tray. Insert a disc, data side down, into the round recess in the
tray.
NOTE: Be sure that your disc is clean and in good shape for playback. Excessive dust, scratches, markings
etc. could prevent normal disc playback.
Playing a Disc
Press the PLAY button on the front panel to begin disc playback. Press the |<</>>| buttons once to skip
to the previous or next track or hold them down to scan through a track. Press the STOP button to cease
playback of the disc.
NOTE: You cannot use the RECORDING LEVEL control to adjust the volume when playing a disc in Playback
Mode. You will need to use the volume on the mixer or amp that you are outputting to.
Recording onto a Disc
Preparing to Record
• If using a CD-R, make sure that there is not already data stored on the disc as you will be unable to burn
anything onto it.
• If you are going to rewrite onto a CD-RW*, be sure to erase the data using the ERASE feature on the CDR-
1000 PRO before recording. See the Erasing instructions in this manual.
• If using an 8cm CD-R/RW disc, you must use the Digital input on the rear panel of the CDR-1000 PRO.
The Analog input does not support 8cm CD-R/RW.
NOTE: Be sure that your disc is clean and in good shape for recording. Excessive dust, scratches, markings,
etc. could prevent successful recording.
NOTE: Make sure all players or mixers are connected to the proper inputs and outputs of the CDR-1000
PRO.
* Most standard CD players (Car audio, home audio, etc.) do not support CD-RW discs. If using CD-RW
discs, make sure that your CD player specifies that it is CD-RW compatible.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations cont.
Recording
1. Switch the CDR-1000 PRO to Record Mode by pressing the RECORD button.
2. To begin recording press the START button. The LCD display will say RECORDING and show the track num-
ber along with the elapsed recording time.
3. To stop recording press the CANCEL button. This will also cause you to exit Record Mode.
CDR-1000 PRO
CDR-1000 PRO
NOTE: For optimum recording quality, be sure that the recording volume level is neither too high nor too low.
Refer to the input volume meter when adjusting recording volume. If the orange bars at the top light up then
the input level is too loud and it could cause distortion on the recording.
Pausing Recording
To pause recording
1. While a disc is recording, press the PLAY/PAUSE button. The LCD display will say “PAUSE”.
2. To resume recording, press the PLAY/PAUSE button while the recording process is paused. The LCD
display will say “RECORDING”.
Creating Tracks on a Disc
On music CDs, each song is on a different track. The CDR-1000 PRO allows you to easily create these tracks
on a disc so that you can jump to a certain song.
To create a track
1. While the disc is already recording, press the RECORD button.
2. Recording will pause for 5 seconds.
3. The track number will change and the disc will begin recording on a new track.
CDR-1000 PRO
NOTE: The CDR-1000 PRO will not automatically change to a new track when copying a CD.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operations cont.
Finalizing a Disc
After you have finished recording onto a disc, you will need to FINALIZE it so that it will be compatible with
standard disc players. If a disc has not been finalized, it can only be played back in the CDR-1000 PRO.
NOTE: The CDR-1000 PRO must be in Playback Mode in order to finalize a disc. Make sure it is not in
Record Mode.
Follow these steps to successfully FINALIZE your disc.
1. Insert the disc into the CDR-1000 PRO’s disc tray and close the tray.
2. If in Record Mode, press the STOP button to enter Playback Mode. The Finalizing function only works in
Playback Mode
3. Press the FINALIZE button.
4. The display screen will ask you if you want to continue with the finalizing process. Press the START
button to begin finalizing. The display screen will say “FINALIZING” until the process is finished. The display
will show how much time is left in the Finalizing process.
When the disc has been finalized, it is ready to be played in standard CD players. I.e. Car stereos, CD-
ROM compatible drives, home stereos, etc.
NOTE: You will not be able to burn any more music onto a disc once it has been finalized.
Erasing the Contents of a CD-RW
The ERASE function only works on CD Rewritable (CD-RW) discs.
Follow these steps to successfully ERASE the contents of your CD-RW disc
1. Insert the CD-RW disc into the CDR-1000 PRO’s disc tray and close the tray.
2. If in recording mode, press the STOP button to enter Playback Mode. The Erasing function only works
in Playback Mode
3. Press the ERASE button. The LCD display will ask you if you are sure you want to ERASE.
4. Press the START button to begin erasing the data from the CD-RW disc. The display will show how
much time is left in the erasing process.
CDR-1000 PRO
NOTE: The erasing process cannot be cancelled once it has begun so be sure that you want to erase the
disc.
Disclaimer: VocoPro will not be held liable for any erased data.
. (**PIC of the display showing this info)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem
Solution
There is no power when the power switch is turned on.
• Make sure the power cord is firmly connected to the
AC IN terminal on the back of the CDG-1000 PRO.
• Make sure the power cord is securely connected to the
power outlet or the surge protector/power strip.
• Make sure your surge protector/power strip is plugged
in and turned on.
The input source (i.e. disc player, karaoke machine) is
playing but there is no sound from the output source
(i.e. amp or mixer).
• Press the record button to switch the CDG-1000 PRO
to recording mode. The input audio can only be heard
when the CDG-1000 PRO is in recording mode.
• Make sure the audio ins and outs are connected prop-
erly.
• If using the Analog RCA inputs be sure the CDR-1000
PRO is in ANALOG mode and if using the DIGITAL input
make sure it is in DIGITAL mode.
The LED display says “ERROR! FINALIZED DISC”.
The LED display says “ERROR! CDRW DISC ONLY”.
The final recording sounds too loud or distorted.
• If the disc is finalized, it cannot be recorded on. Put in
a blank or non-”Finalized” disc for recording.
• This happens if you try to ERASE a CD-R. The ERASE
function only works on CD-Rewritables (CD-RWs).
• The recording volume may have been set too high. Try
re-recording and adjust the recording volume so that the
bars on the Input Volume meter do not reach the orange
bars.
I am unable to record onto an 8cm CD-R/RW disc.
• Make sure you are connected to the Digital input. The
Analog input does not support 8cm discs.
The CD-RW disc will not play in my CD player (Car audio,
home audio, etc.)
• Most standard CD players (Car audio, home audio,
etc.) do not support CD-RW discs. If using CD-RW discs,
make sure that your CD player specifies that it is CD-RW
compatible.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Solution
Problem
• The recording volume may have been set too low.
Try re-recording and adjust the recording volume so
that the bars on the Input Volume meter stay around
the middle.
The final recording is not loud enough.
The disc will not play in other disc players.
The LED display says “UNKNOWN”.
• Make sure the disc has been FINALIZED. See instruc-
tions on finalizing a disc in the Operations section of this
manual.
• The disc you’ve inserted is corrupted or not compatible
with the CDR-1000 PRO. Use a different disc or a differ-
ent brand of disc.
The LCD display says “NO DISC” when there is a disc is in
the disc tray.
• The disc is not compatible or damaged.
• It is a DVD disc. CDR-1000 PRO does not read
DVD discs.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Vocopro 2005
V 1.1
W WW.VOCOPRO.COM
Download from Www.Somanuals.com. All Manuals Search And Download.
|