Safety Instructions
Introduction
Image Resolution
Compatibility
Unpacking the Projector
Usage Guidelines
If You Need Assistance
Warranty
1
4
Setting up the Projector
Connecting a Computer
Connecting a Video Player
Turning Off the Projector
Using the Projector
Basic Image Adjustment
Using the Remote Control
Adjusting the Projector
Using the On-Screen Menus
Display Menu
Audio Menu
Image Menu
Controls Menu
Language Menu
16
19
Status Menu
Maintenance & Troubleshooting
Cleaning the Lens
Replacing the Projection Lamp
Replacing the Batteries in the Remote Control
Using the Kensington Lock
Troubleshooting
27
27
27
30
30
31
i
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INSTRUCTIONS
Please read and follow all safety instructions provided BEFORE
using your new projector. Failure to comply with safety instruc-
tions may result in fire, electrical shock, or personal injury and
may damage or impair protection provided by equipment. Please
save all safety instructions.
Safety Definitions:
• Warning: Statements identify conditions or practices that
could result in personal injury.
• Caution:Statements identify conditions or practices that could
result in damage to your equipment.
Safety Symbols:
Attention: For information about usage of a feature, please
refer to the User’s Guide.
Warning: Hot surface. Do not touch.
An arrow pointing to the lamp door on the projector.
Safety Terms:
• Warning: Don’t look directly into the lens when the lamp is
turned on.
•Warning: To replace the lamp, turn the projector off by
unplugging the power cord. To avoid burns, wait 30
minutes before opening the lamp door. Follow all instructions
provided in this User’s Guide.
•Warning: Please use the power cord provided. Connect
the power cord to a receptacle with a protective safety
(earth) ground terminal.
• Warning: Refer all service to qualified service personnel. Ser-
vicing your own projector will void the warranty. See the fol-
lowing page for the customer service contact information.
• Caution: Don’t block ventilation openings.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
S
a
f
e
t
y
I
n
s
t
r
u
c
t
i
o
n
s
• Caution: Don’t set liquids on the projector. Spilled liquids may
damage your projector.
• Caution: Don’t place the projector on a hot surface or in direct
sunlight.
• Caution: Do not drop the projector. Transport the projector in a
vendor-approved case; refer to your Toshiba dealer or
projectors.toshiba.com for more information.
Important Operating Considerations
Do not place the projector on a tablecloth or other soft covering
that may block the vents. In the unlikely event of the bulb ruptur-
ing, thoroughly clean the area behind the projector and discard
any edible items placed in that area.
Do not place objects in
this area behind the projector
Customer Service
If you need assistance, contact Toshiba Technical Support.
• In North America, call Toshiba’s toll-free customer service
& technical support at 800-457-7777 (available 24 hours a
day, 7 days a week).
• For web-based or other electronic technical support, please
visit Toshiba at support.toshiba.com.
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
The Toshiba® TDP-B1™ is specifically designed for the mobile
presenter. It packs XGA 1024x768 graphics with 16.7 million col-
ors into a small, 4.8 pound package. It generates crisp, clear
images using Digital Light Processing™ (DLP) technology. The
TDP-B1 is easy to connect, easy to use, easy to transport, and easy
to maintain.
Image Resolution
NOTE: The TDP-B1 automatically
expands 640x480 and 800x600
images to 1024x768. You can dis-
play these images at their native
resolutions by turning off the Auto
Resize feature. See “Auto Resize”
on page 21 for more information.
The XGA resolution of the TDP-B1’s projected image is 1024x768.
The projector cannot compress screen resolutions above
1024x768. If your computer’s screen resolution is higher than
1024x768, reset it to a lower resolution before you connect the
projector.
Compatibility
The projector is compatible with a wide variety of computers and
video devices, including:
• IBM-compatible computers, including portable computers, up
to 1024x768 resolution.
• Apple Macintosh and PowerBook computers up to 1024x768
resolution.
• Most standard VCRs, DVD players, camcorders and laser disc
players.
Unpacking the Projector
The projector comes with the items shown in Figure 1. Check to
make sure all are included. Contact your Toshiba dealer imme-
diately if anything is missing.
If you are experienced in setting up presentation systems, use the
Quick Start card that was included in the shipping box. For com-
plete details on connecting and operating the projector, refer to
this User’s Guide. User’s Guides are also available for download
from our website at projectors.toshiba.com.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
I
n
t
r
o
d
u
c
t
i
o
n
NOTE: The contents of your
1
shipping box may vary depending
on the projector configuration
you’ve ordered.
4
3
2
5
8
6
7
10
9
FIGURE 1
Shipping box contents
1. TDP-B1 projector + lens cap
2. Remote control
6. Audio cable adapter
7. Audio cable
3. Power cord
8. Composite video cable
9. PS/2 mouse cable
4. User’s Guide and quick start
card
5.
VESA computer cable
10. USB mouse cable
2
Download from Www.Somanuals.com. All Manuals Search And Download.
speaker
keypad
zoom ring
Kensington Lock
connector panel
focus ring
power
cord
connector
FIGURE 2
Side view of projector
Usage Guidelines
• Do not look directly into the projection lens when the lamp is
turned on. The bright light may harm your eyes.
• Do not block the grills on the projector. Restricting the air flow
can cause it to overheat and turn off. If this happens, you must
wait a minute before attempting to turn it back on.
• Handle the projector as you would any product with glass
components. Be especially careful not to drop it.
• Avoid leaving the projector in direct sunlight or extreme cold
for extended periods of time. If this happens, allow it to reach
room temperature before use.
• Transport the projector in a vendor-approved hard or soft case.
Refer to your Toshiba dealer or projectors.toshiba.com for more
information.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
I
n
t
r
o
d
u
c
t
i
o
n
If You Need Assistance
The first place to look for help is in this manual. Be sure to check
the guidelines in “Troubleshooting” on page 31. Or, check the
Service and Support section of our website at
support.toshiba.com.
If those sources don’t answer your question, call your Toshiba
dealer. You can also call Toshiba Technical Support directly.
• In North America, call Toshiba’s toll-free customer service
& technical support at 800-457-7777 (available 24 hours a
day, 7 days a week).
• For web-based or other electronic technical support, please
visit Toshiba at support.toshiba.com..
Warranty
This product is backed by a limited two-year warranty. The
details of the warranty are printed at the back of this manual. A
longer term warranty can be purchased from your Toshiba dealer.
Refer to your Toshiba dealer or support.toshiba.com for more
information.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING UP THE PROJECTOR
• The projector must be within 10 feet (3 m) of your power
source and within 6 feet (1.8 m) of your computer.
• If you want to project from behind a translucent screen, set
on page 24 to reverse the image.
• The distance from the lens of the projector to the screen and
the zoom setting determine the size of the projected image.
Figure 3 shows three projected image sizes. For more infor-
mation about image size, see “Projected Image Size” on
page 44.
20 ft.
12 ft.
5 ft.
FIGURE 3
Projected image size at minimum zoom
3 Make sure the projector is unplugged and your computer is
turned off.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
NOTE: Before you continue,
make sure the projector is
unplugged and your equipment is
turned off. If you’re connecting a
computer, make sure the distance
between it and the projector is 6
feet or less.
S-video
composite
video
mouse
VESA computer
input
Audio in
FIGURE 4
Connector panel
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Computer
1 Plug one end of the VESA computer cable into the video con-
nector on your computer.
2 Plug the other end of the VESA computer cable into the
connector on the projector.
NOTE: Many portable computers
do not automatically turn on their
external video port when a sec-
ondary display device such as a
projector is connected. Refer to
your computer manual for the
command that activates the exter-
nal video port. Activation com-
mands for some portable
audio cable
VESA cable
computers are listed in the Appen-
dix of this manual on page 38 or
visit support.toshiba.com for
more information.
FIGURE 5
Connecting the projector to a computer
Do you want to play your computer’s audio on the projector?
1 Plug either end of the audio cable into the audio connector on
your computer.
2 Plug the other end of the audio cable into the
connector
on the projector.
NOTE: If you are connecting an
older Macintosh computer that
does not have a 15-pin connector,
you must use a Mac adaptor
between the computer and the
projector. See “Optional Accesso-
ries” on page 37.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
Do you want to control the computer’s mouse from the projector’s
remote or keypad?
If your computer has a PS/2 connector, use the PS/2 mouse cable.
1 Plug the end of the PS/2 mouse cable with 6 pins into the
mouse connector on your computer.
2 Plug the end of the PS/2 mouse cable with 9 pins into the
connector on the projector.
If your computer has a USB connector and is running Windows 98,
use the USB mouse cable.
1 Plug the
end of the USB mouse cable into the
mouse connector on your computer.
NOTE: The USB mouse is
supported for use with
Windows 98 only.
2 Plug the
end of the USB mouse cable into the
connector
on the projector.
computer to use the USB feature. Windows 98 ships with the
appropriate drivers.
Now you’re ready to power up the projector and your computer.
Skip to “Powering up the Projector and Adjusting the Image” on
page 11.
NOTE: You do not need to restart
your computer after connecting a
USB mouse to use it (it is hot-
pluggable). You must restart your
computer after plugging in a PS-2
mouse.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Video Player
1 If your video player uses a round, one-prong composite video
and composite video cable that shipped with the projector.
nector, you’ll need an S-video cable in addition to the audio
cable and audio adapter. The S-video cable is sold sepa-
rately. (See “Optional Accessories” on page 37.)
2 Plug the composite video cable’s yellow connector into the
“video-out” connector on your video player (Figure 6). This
connector may be labeled “To Monitor.”
• If you’re using an S-video cable, connect it to the “S-video
out” connector on the video player (Figure 7).
3 Plug the other yellow connector into the composite video con-
nector
• If you’re using S-video, plug the other end of the cable into
the “S-video” connector on the projector (Figure 7).
on the projector.
audio
adapter
composite video cable
audio cable
FIGURE 6
Connecting the projector to a video player using the standard video cable (with com-
posite video connector) and the audio cable and adapter
9
Download from Www.Somanuals.com. All Manuals Search And Download.
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
audio
adapter
S-video
cable
audio cable
FIGURE 7
and adapter
4 Plug the audio adapter’s white connector into the left “audio
out” connector on your video player. Plug the adapter’s red
connector into the right “audio out” connector on the video
player (Figure 6 and Figure 7).
NOTE: The audio adapter is
provided so that the same audio
cable used to connect a computer
can be used with the adapter to
connect a VCR.
5 Plug the audio adapter’s other end into the audio cable.
connector on the
projector.
The projector is compatible with these major broadcast video
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, and SECAM.
It automatically adjusts to optimize its performance for the
incoming video. See “Video Standard” on page 23 for details.
CAUTION: Your video player
may also have a “Video Out”
connector for a coaxial cable
connection. DO NOT use this to
connect to the projector.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Powering up the Projector and Adjusting the Image
1 Remove the lens cap.
NOTE: Always use the power cord
2 Plug the power cord into the side of the projector, then plug it
into your electrical outlet. A surge-protected power strip is
recommended.
that shipped with the projector.
• The fans start to run, and the Lamp LED on the top of the
projector (Figure 11 on page 16) lights orange until the soft-
ware has initialized. When initialization is complete, the
you can press the lamp on/off button to turn the lamp on
and off.
3 Turn on the lamp by pressing the lamp on/off button
on
the keypad (see Figure 11 on page 16).
• The startup screen appears.
4 If you connected a video player, turn it on.
• The video image should display on the projection screen. If
a computer source is active, press the source button on the
keypad (page 16) or the video button on the remote to dis-
play your video image. You can select a default source to
determine which source the projector examines first during
power-up for active video; see “Default Source” on page 24.
• Use the volume buttons to adjust the volume.
5 Turn on your computer.
NOTE: With some computers,
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
computer’s documentation to
determine the correct order.
• The computer image should display on the projection
screen. If a video source is active, press the source button on
the keypad or the computer button on the remote to display
your computer’s image. Make sure your computer’s exter-
nal video port is activated; see “Portable Computer Activa-
• If necessary, make adjustments to the image using the pro-
jector’s on-screen menus. To open the menus, press the
menu button on the keypad or remote, then select the Dis-
play or Image sub-menu. For more information about the
menus, see page 18.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
S
e
t
t
i
n
g
u
p
t
h
e
P
r
o
j
e
c
t
o
r
If you want to turn off the projector for a short period of time,
press the standby button on the keypad or remote. This blanks the
screen for fifteen minutes, but keeps the projector running. (You
can change the amount of time the projector stays in standby
mode; see “Standby Time” on page 23 for details.) After 15 min-
utes, the lamp goes out (the projector keeps running). To exit
standby mode, press the standby button again. (It may take sev-
eral seconds for the projection lamp to reach full power and
project the image again.)
To completely power off the projector, unplug it. If you want to
turn the lamp back on immediately, you must allow about a
minute for the lamp to cool. The lamp won’t light if it’s too hot.
NOTE: Lamp life will be extended
if you turn the lamp off, then wait
1 minute while the lamp cools
before unplugging the projector.
The Lamp LED will light green
when the lamp has cooled. See
page 16 for details on the Lamp
LED.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE PROJECTOR
This section describes how to use and make adjustments to the
buttons and the options available from the on-screen menus.
Basic Image Adjustment
order (page 11).
2 If the image doesn’t display completely, zoom the image
(page 15), adjust the height of the projector (page 15) or center
the image by adjusting its horizontal or vertical position
screen.
4 If the image appears to shimmer or if it has blurry vertical
bars after you have adjusted the focus, turn Auto Image
(page 21) off and then back on to reset the automatic sync and
tracking. If that doesn’t clear up the image, turn Auto Image
off and adjust the sync (page 21) and/or the tracking
(page 22) manually.
5 If the colors don’t look right, adjust the brightness (page 19).
Using the Remote Control
The projector ships with a remote that has four function buttons,
a disk mouse and two mouse buttons, one on the top of the
remote and one on the bottom.
NOTE: To control the computer’s
mouse from the projector’s remote
or keypad, you must connect a
mouse cable to the projector and
the computer. See page 8 for
details.
Point the remote control at the projection screen or at the front of
the projector. The range for optimum operation is about 25 feet. If
you point the remote at the projection screen, the distance to the
screen and back to the projector must be less than or equal to 25
feet. For best results, point the remote directly at the projector.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
disk mouse
right mouse button
left mouse button
(on underside of remote)
FIGURE 8
Remote control
on the screen. You can move the cursor at any angle by pressing
the corresponding edge of the disk. The mouse button on the top
of the remote simulates your computer’s right mouse button; the
button on the bottom simulates your computer’s left mouse but-
ton. See “Using the Keypad and Remote Buttons” starting on
page 16 for a description of the four function buttons.
NOTE: If the remote is inactive
for several minutes, it “sleeps” to
conserve battery life. Press any
button except the disk mouse to
re-activate the remote.
If you are creating presentations in Microsoft® PowerPoint®, you
can use the remote’s mouse buttons to navigate through your
presentation while in Slide Show mode. To configure PowerPoint
for this, choose Options from the Tools menu, click the View Tab,
de-select the “Popup Menu on Right Mouse Click” option in the
Slide Show section, then click OK. Then, when you’re in Power-
Point’s Slide Show mode, a left click advances to the next slide
and a right click returns to the previous slide (other PowerPoint
modes are not affected).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the Projector
To focus the image, rotate the focus ring (Figure 9) until the image
is clear. To zoom the image, rotate the zoom ring. This adjusts the
image size without affecting focus.
zoom ring
focus ring
FIGURE 9
The projector is equipped with a self-locking, quick-release eleva-
tor foot and button (Figure 10).
To raise the projector:
1 Press and hold the elevator button (Figure 10).
2 Raise the projector to the height you want, then release the
button to lock the elevator foot into position.
elevator foot
elevator button
(under finger)
FIGURE 10
Adjusting the height of the projector
15
Download from Www.Somanuals.com. All Manuals Search And Download.
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Using the Keypad and Remote Buttons
While the menus are displayed, the volume, source, and standby
buttons on the keypad act as menu navigation buttons. See
“Using the On-Screen Menus” on page 18 for details.
lamp LED
FIGURE 11
Keypad and remote buttons
Lamp on/off (keypad only)
Press the lamp on/off button to turn the lamp on or off. The Lamp
LED indicates the state of the lamp. A green Lamp LED indicates
that you can turn the lamp on, or the lamp is currently on. An
orange LED indicates the software is initializing or the lamp is
cooling. Do not press the lamp on/off button when the LED is
orange.
Menu
Press the menu button to open the on-screen menus. Press menu
again to close the menus. When you close the menus, the projec-
tor saves any changes you made. For more information about the
on-screen menus, see page 18.
Source (keypad only)
or Computer and Video (remote only)
When you have more than one source (computer and video) con-
nected to the projector, select between them by pressing the
source button on the keypad or the computer or video button on
the remote.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Standby
When you press standby, the display and audio turn off and a
blank screen is displayed for 15 minutes. You can change the
amount of time the projector stays in standby mode; see
“Standby Time” on page 23 for details.
• If you press standby again within 15 minutes, the projector
returns to normal operations immediately.
• If you press standby again after 15 minutes, there is about a
60 second delay before the lamp turns back on.
• If you don’t press standby again, the lamp turns off after 15
minutes.
Volume (keypad only)
To increase the volume, press volume +
ume, press volume -
. To decrease the vol-
.
Volume adjustments are saved for each source you have con-
nected.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Using the On-Screen Menus
The projector has six drop-down menus that allow you to make
image adjustments and change a variety of settings. Most of these
adjustments aren’t available directly from the keypad.
To open the on-screen menus, press the menu button on the
keypad or remote. This changes the volume, source, and standby
buttons on the keypad to menu navigation buttons. Press the
corresponding buttons to move the cursor up, down, left, or
right, or use the disk mouse on the remote. To select a menu,
move the cursor left and right to highlight the menu you want.
The drop-down menu appears.
NOTE: Some menu items may be
grayed out at certain times. This
indicates the item is not applicable
to your setup (for example, video
standards do not apply to
computer sources) or the item is
not enabled until another selection
is made (for example, Manual
Tracking is not available until Auto
Image is turned off).
use these buttons to navigate through
the menus
FIGURE 12
Keypad navigation buttons and drop-down menu
To change a menu setting, use the up and down navigation but-
tons on the keypad or the disk mouse on the remote to move the
cursor up and down to the item you want to change (the selected
item is highlighted), then use the left and right navigation but-
tons to adjust a setting. Some submenus, such as Brightness, con-
sist of a slider bar you use to increase or decrease a value; some
submenus, such as Standby Time, consist of options you scroll
through to select the desired one. All changes are saved when
you close the menus.
To access another menu, use the up and down navigation buttons
or the disk mouse to move back to the top of the current menu,
then use the left and right navigation buttons to move to another
menu.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Menu
FIGURE 13
Display menu
Brightness
Adjusting the brightness changes the intensity of the image.
• Press the left navigation button to darken the image.
• Press the right navigation button to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
• Press the left navigation button to decrease the contrast.
• Press the right navigation button to increase the contrast, mak-
ing the blacks appear blacker and the whites appear whiter.
Tint
The tint adjusts the red-green color balance in the projected
image. Changing the Tint setting has no effect on PAL or SECAM
video sources.
• Press the left navigation button to increase the amount of green
in the image.
• Press the right navigation button to increase the amount of red
in the image.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Color
The color setting adjusts a video image from black and white to
fully saturated color.
• Press the left mouse button to decrease the amount of color in
the image.
• Press the right mouse button to increase the amount of color in
the image.
Blank Screen
Blank Screen determines what color is displayed when there is no
active source and when the projector is in standby. Click the left
or right navigation button to toggle between blue and black.
Reset All
Click the left or right navigation button to reset all the options
(except Language, Video Standard, Rear Projection, and Standby
Time) in all the menus to their original settings.
Audio Menu
FIGURE 14
Audio menu
Volume
• Press the left navigation button to decrease the volume.
NOTE: Changing the volume
using the menu is the same as
changing it using the keypad.
• Press the right navigation button to increase the volume.
Volume adjustments you make are saved for each source.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Image Menu
FIGURE 15
Image menu
Auto Image
The projector automatically adjusts tracking, signal synchroniza-
tion and vertical and horizontal position for most computers
(Auto Image does not apply to video sources). If you want to
adjust these features manually, you must turn off Auto Image first
by highlighting Auto Image in the Image menu and clicking the
left or right navigation button to select “off”.
NOTE: Some screen savers inter-
fere with the operation of Auto
Image. If you’re experiencing prob-
lems, try turning your screen saver
off, then turning Auto Image off
and back on.
Auto Resize
Auto Resize automatically resizes the image by scaling it up. It
only affects computer images that are not the projector’s native
resolution.
When Auto Resize is on, the projector makes the best fit of the
image to the computer screen. If you turn Auto Resize off (by
highlighting it in the Image menu and clicking the left or right
navigation button to select “off”), the image may be either
cropped or too small for the screen.
Manual Sync
The projector adjusts signal synchronization automatically for
most computers. But if the projected computer image looks fuzzy
or streaked, try turning Auto Image off then back on again. If the
image still looks bad, try adjusting the signal synchronization
manually:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
1 Turn Auto Image off.
2 Highlight Manual sync, then press the left or right navigation
button repeatedly until the image is sharp and free of streaks.
Manual Tracking
The projector adjusts tracking automatically to match the video
signal from your computer. However, if the display shows evenly
spaced, fuzzy, vertical lines or if the projected image is too wide
or too narrow for the screen, try turning Auto Image off then back
on again. If the image is still bad, try adjusting the tracking man-
ually:
1 Turn Auto Image off.
NOTE: The Manual Sync,
Manual Tracking, Horiz.
Position and Vert. Position
options are available only for
computer sources. The projector
sets these options automatically
for video sources.
2 Highlight Manual tracking, then press the left or right naviga-
tion button repeatedly until the fuzzy vertical bars are gone.
Horizontal position
Follow these steps to manually adjust the horizontal position:
1 Turn Auto Image off.
2 Highlight Horizontal position, then press the left navigation
button to move the image right or press the right navigation
button to move the image left.
Positioning adjustments are saved when you power off the pro-
jector.
Vertical position
Follow these steps to manually adjust the vertical position.
1 Turn Auto Image off.
2 Highlight Vertical position, then press the left navigation but-
ton to move the image down or press the right navigation but-
ton to move the image up.
Positioning adjustments are saved when you power off the pro-
jector.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Controls Menu
FIGURE 16
Controls menu
Video Standard
When Video standard is set to Auto, the projector attempts to
pick the video standard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-N,
or SECAM) automatically based on the input signal it receives.
(The video standard options may vary depending on your region
of the world.) If the projector is unable to detect the correct stan-
dard, the colors might not look right or the image might appear
“torn.” If this happens, manually select a standard by clicking the
left or right navigation button and cycling through the standards.
NOTE: If you already know the
video standard used in your geo-
graphical area, it’s often best to
manually select it.
Standby Time
This option lets you select how long the lamp stays on and the
blank screen is displayed when the projector enters standby
mode before the projector turns off. Select among 1, 5, 10, and 15
minutes and 1 and 2 hours by clicking the left or right navigation
button and cycling through the options.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Rear Projection
When you turn Rear Projection on, the projector reverses the
image so you can project from behind a translucent screen. High-
light Rear Projection, then click the left or right navigation button
to turn this feature on and off.
Default Source
Default Source toggles between Computer and Video. This deter-
mines which source the projector checks first for active video
during power-up. Highlight Default Source and click the left or
right navigation button to toggle between the options.
Auto Source Select
This setting toggles between On and Off. When this feature is Off,
the projector defaults to the source selected in Default Source. To
display another source, you must manually select one by press-
ing the source button on the keypad or the computer or video but-
ton on the remote. When this feature is On, the projector
automatically finds the active source, checking the default source
first. Highlight Auto Source Select and click the left or right navi-
gation button to turn this feature on and off.
Plug and Play
This setting toggles between On and Off. When it is On, most
new computers will automatically recognize the projector, then
set the monitor resolution and refresh rate accordingly. You need
to set the Plug and Play setting to Off for the projector to display
properly on some older computers. The Plug and Play setting
does not affect video images.
If the projector’s display constantly changes between the com-
puter image and the message, “Perfecting the image”, you may
need to turn Plug and Play Off.
Display Messages
This setting toggles between On and Off. When this feature is On,
status messages such as “No signal detected” or “Standby
Active” appear in the lower-right corner of the screen. Click the
left or right navigation button to turn this feature off and not see
status messages.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Startup Screen
This setting toggles between On and Off. When this feature is On,
the startup screen appears when the projector starts up and
remains until an active source is detected. Click the left or right
navigation button to turn this feature off and display a plain
black or blue screen instead of the startup screen.
Language Menu
FIGURE 17
Language menu
You can display the on-screen menus in English, French, German,
and Spanish.
• Move the cursor to the language you want, then click the left or
right navigation button. The menus redraw immediately.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
U
s
i
n
g
t
h
e
P
r
o
j
e
c
t
o
r
Status Menu
This is a read-only window for informational purposes. To dis-
play the status window, select Show status from the menu, then
click the left or right navigation button. To remove the window,
click the left or right navigation button.
FIGURE 18
Status menu
Lamp hours used
Indicates how many hours the current lamp has been in use. The
counter starts at zero hours and counts each hour the lamp is in
use. Change the bulb when the brightness is no longer accept-
able. See “Replacing the Projection Lamp” on page 27 for details.
Computer resolution
Shows your computer’s resolution setting. To change this, go to
your computer’s Control Panel and adjust the resolution in the
Display tab. See your computer’s user’s guide for details.
Horizontal refresh rate
The time period that one horizontal line is displayed.
Vertical refresh rate
The time period that one video frame is displayed.
Mute status
Indicates if the audio is muted.
Software version
Indicates the projector’s software version. This information is
useful when contacting Technical Support.
Source
26
Indicates the active source, Computer or Video.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE & TROUBLESHOOTING
This section describes how to:
•clean the lens
•replace the projection lamp
•replace the batteries in the remote
•use the Kensington lock feature
•troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner.
• Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular
motion.
3 If you don’t intend to use the projector immediately, replace
the lens cap.
Replacing the Projection Lamp
The lamp hour counter in the Status menu counts the number of
hours the lamp has been in use. Replace the lamp when the
brightness is no longer acceptable. You can order new lamp mod-
ules from your Toshiba dealer. See “Accessories” on page 36 for
information. In the unlikely event of a lamp rupture, please con-
tact your Toshiba dealer.
WARNING: To avoid burns,
allow the projector to cool for at
least 30 minutes before you open
the lamp module door. Never
extract the lamp module while the
lamp is operating.
Follow these steps to replace the projection lamp:
1 Turn off the projector by unplugging the power cord.
2 Wait 30 minutes to allow the projector to cool thoroughly.
3 Invert the projector on a flat surface, then insert a small screw-
driver or other flat object into the tab on the lamp module
door (Figure 19).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
4 Pull the lamp door up and remove it.
WARNING: Be extremely careful
when removing the lamp module.
In the unlikely event that the bulb
ruptures, please contact your
Toshiba dealer, as small glass
fragments may be generated. The
lamp module is designed to
contain these fragments, but use
caution when removing the lamp
module.
FIGURE 19
Removing the lamp door
5 Loosen the two non-removable screws on the outside of the
module.
CAUTION: Never operate the
projector with the lamp door open
or removed. This disrupts the air
flow and causes the projector to
overheat.
FIGURE 20
Loosening the screws on the lamp module
28
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Lift and grasp the pull tab and lift the module out (Figure 21).
pull tab
FIGURE 21
Removing the lamp module
7 Install the new lamp module, being sure to align the connec-
tors properly.
WARNING: Do not drop the
lamp module or touch the glass
bulb! The glass may shatter and
cause injury.
8 Push the module in until it is flush with the bottom case of the
projector.
9 Tighten the screws on the outside of the module.
10 Replace the lamp door by inserting the hooks on the rear of
the lamp door into the projector and pressing the lamp door
into place. If the lamp door does not fit properly or bulges out,
remove the door and re-seat the lamp module.
11 Plug in the power cord to turn the projector back on.
12 To reset the lamp hour counter in the Status window, press
and hold the volume - button, then press the menu button
(while still holding down the volume - button) for 5 seconds.
Verify that the counter was reset by pressing the menu button
and viewing the counter in the Status window.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Replacing the Batteries in the Remote Control
The life of the batteries depends on how often and how long you
use the remote. Symptoms of low battery charge include erratic
responses when using the remote and a reduced range of opera-
tion.
Follow these steps to replace the batteries:
1 Turn the remote face down in your hand.
2 Slide the battery cover off the end of the remote.
3 Remove the old batteries and dispose of them in an environ-
mentally proper manner.
4 Install two new AAA alkaline batteries. Make sure you install
each in the correct direction.
Using the Kensington Lock
The projector has a Kensington Security Standard connector for
use with a Kensington MicroSaver Security System (Figure 22).
See “Optional Accessories” on page 37 for ordering information.
Refer to the information that came with the Kensington System
for instructions on how to use it to secure the projector.
FIGURE 22
Installing the Kensington lock
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Problem: Nothing on projection screen
•Make sure that the power cord is properly connected to a fully
functional AC electrical outlet. Make sure that the power cord
is also properly connected to the projector.
•If the projector is plugged into a power strip, make sure the
power strip is turned on.
lens at the front of the projector.
•Make sure the lamp is switched on.
•Check the projector’s lamp to ensure that it is securely con-
nected in the lamp module. See “Replacing the Projection
Lamp” on page 27.
•Make sure that the cables do not have any bent pins.
Problem: Color or text not being projected
•You might need to adjust the brightness up or down until the
text is visible. Refer to “Brightness” on page 19 for more infor-
mation.
Problem: The screen resolution is not right
no greater than 1024x768.
Problem: Image isn’t centered on the screen
•Move the projector to reposition the image.
•Be sure the projector is at a 90 degree angle to the screen.
•Verify that the cables are connected correctly. See page 7
through page 8 for connection procedures.
•Verify that the proper input source is connected. See “Source
(keypad only) or Computer and Video (remote only)” on
page 16.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
•You might need to turn everything off and power up the
equipment again in the proper order. Refer to your com-
puter’s documentation to determine the correct order.
•Make sure your computer’s external video port is turned on.
See the “Portable Computer Activation Chart” on page 38 or
your computer’s manual for details.
•Make sure your computer’s video board is installed and con-
figured correctly.
•Make sure your computer has a compatible video board. The
projector isn’t CGA, EGA or SXGA compatible.
If you’re using Windows 98:
1 Open “My Computer” icon, the Control Panel folder and
then the Display icon.
2 Click the Settings tab.
3 Verify that the Desktop area is set to 1024x768 or less.
Problem: Image is too wide or narrow for screen
•Adjust the zoom or projector placement.
•Adjust the resolution of your video card if it’s greater than
1024x768.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem: Image is out of focus
•Turn the projection lens to focus the image.
•Make sure the projection screen is at least 5 feet (1.5 m) from
the projector.
Problem: Image and menus are reversed left to right
•Rear projection mode is probably turned on. Turn Rear Projec-
tion off in the Controls menu. The image should immediately
return to forward projection. See “Rear Projection” on
page 24.
Problem: the projector displays vertical lines, “bleeding” or
spots
•Adjust the brightness. See “Brightness” on page 19.
•Check the projection lens to see if it needs cleaning.
Problem: no sound
•Adjust volume.
•Verify audio/input connections.
•Adjust audio source.
Problem: Image is “noisy” or streaked
Try these steps in this order.
2 Turn Auto Image off and then back on again. See “Auto
Image” on page 21.
3 Turn Auto Image off and adjust the synchronization and track-
ing manually to find an optimal setting. See “Manual Sync”
on page 21 and “Manual Tracking” on page 22.
•The problem could be with your computer’s video card. If
possible, connect a different computer.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
M
a
i
n
t
e
n
a
n
c
e
&
T
r
o
u
b
l
e
s
h
o
o
t
i
n
g
Problem: Projected colors don’t match the computer or video
player’s colors
•Just as there are differences in the displays of different moni-
tors, there are often differences between the computer image
and the projected image. Adjust the brightness, tint and/or
“Tint” on page 19 and “Contrast” on page 19.
Problem: Lamp seems to be getting dimmer
•The lamp begins to lose brightness when it has been in use for
a long time. Replace the lamp as described in “Replacing the
Projection Lamp” on page 27.
Problem: Lamp shuts off
•A minor power surge may cause the lamp to shut off. Unplug
the projector, wait at least a minute, then plug it back in.
•Make sure the vents are not blocked.
The most current troubleshooting information (including web-
based and other electronic technical support) is available at
Toshiba’s Service and Support website at
support.toshiba.com.
Before calling your dealer or Toshiba toll-free customer service
and technical support for assistance, please have the following
information available:
•the projector’s serial number
•the resolution of your computer.
In North America, call Toshiba’s toll-free customer service &
technical support at 800-457-7777 (available 24 hours a day, 7 days
a week).
For web-based or other electronic technical support, please visit
Toshiba at support.toshiba.com.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
APPENDIX
Specifications
The TDP-B1 must be operated and stored within the temperature
and humidity ranges specified.
Te m p e r a t u re
Operating
50 to 104° F (10 to 40° C)
Non-operating
-4 to 158° F (-20 to 70° C)
Humidity
Operating and non-oper.
5% to 95% relative humidity, non-condensing
Dimensions
8.75 x 9.75 x 2.5 inches (22.2 x 24.8 x 6.4 cm)
Weight
4.8 lbs. (2.2 kg) unpacked
Altitude
Operating
0 to 10,000 feet (3,048 meters)
Non-operating
0 to 40,000 feet (12,192 meters)
Optics
Focus Range
4.9 - 16 feet (1.5-5 m)
Lamp
Type
120-watt VHP lamp
Input Power Requirements
100-120VAC 6A;50/60Hz
200-240VAC 3A; 50Hz
Audio Input
Input Impedance
Maximum Input Voltage
10K ohm nominal, AC coupled
(L + R )
< 4.5 V for THD ≤ 0.3%
IN
IN PEAK
L
or R < 2.0 Vrms for THD ≤ 0.3%
IN
IN
Sensitivity
100 mV at 1 KHz for 88 dB SPL at 1 meter
3.5 mm (1/8 inch) stereo phone mini
Connector Type
35
Download from Www.Somanuals.com. All Manuals Search And Download.
A
p
p
e
n
d
i
x
Accessories
Standard Accessories
(ship with the projector)
Quick Start card
User’s Guide
Shipping Box
VESA Computer Cable
Composite Video Cable
Computer Audio Cable 6 ft (1.8 m)
Audio Adapter (RCA to 3.5mm)
PS/2 Mouse Cable
USB Mouse Cable
Executive Plus Remote
Projection Lamp Module
Lens Cap
Power Cords (one ships with projector, type depends on country)
NOTE: Use only Toshiba-
approved accessories. Other
North American Power Cord
Australian Power Cord
UK Power Cord
products have not been tested with
the projector.
European Power Cord
Danish Power Cord
Swiss Power Cord
NOTE: You can purchase these
items by contacting your dealer or
visiting Toshiba’s website at
projectors.toshiba.com.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
NOTE: You can purchase these
items by contacting your dealer or
visiting Toshiba’s website at
Deluxe Carry Case
Shipping Case (ATA approved)
Deluxe Travel Case
Macintosh Adaptor
projectors.toshiba.com.
Full-Feature Laser Pro Remote Control
GyroPoint II Radio Frequency Remote
Remote Receiver
Kensington MicroSaver Security System
S-Video Cable
Programming Cable
rd
3
Year Advantage Service Plan
(1 year extension)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
A
p
p
e
n
d
i
x
Portable Computer Activation Chart
Many portable computers do not automatically turn on their
external video port when a projector is connected. Activation
commands for some portable computers are listed in the follow-
ing table. (If your computer is not listed or the given command
does not work, refer to the computer’s documentation for the
appropriate command.) On many portable computers, the activa-
NOTE: Visit our website at
projectors.toshiba.com for the
most current activation chart.
tion function key is labeled with an icon, for example
the text CRT/LCD.
or
NOTE: Usually, pressing the key
commands once activates the
external video port, pressing it
again activates both the external
and internal ports, and pressing it
a third time activates the internal
port. Refer to your computer’s
documentation for details on your
specific model.
Key command to
activate port
Key command to
de-activate port
Computer
Acer
Ctrl-Alt-Esc (for setup)
FN-D or Ctrl-D
Ctrl-FN-D
Ctrl-Alt-Esc (for setup)
FN-D or Ctrl-D
Ctrl-FN-D
AST* **
FN-F5
FN-F5
type from A:/IVGA/CRT
FN-F12
type from A:/IVGA/CRT
FN-F12
AMS
FN-F2
FN-F2
AMT
AT&T
setup screen
setup screen
FN-F3
FN-F6
FN-F3
FN-F6
Advanced Logic
Research
Ctrl-Alt-V
Ctrl-Alt-V
Altima
Shift-Ctrl-Alt-C
Shift-Ctrl-Alt-L
setup VGA/
setup VGA/
Conf.Simulscan
Conf.Simulscan
Ambra**
FN-F12
FN-F12
FN-F5
FN-F5
F2/Choose Option/F5
setup menu
Shift-Ctrl-D
F2/Choose Option/F5
setup menu
Shift-Ctrl-D
Amrel* **
Apple
Aspen
Award
see Mac Portable and Mac PowerBook
automatic
FN-F6
automatic
FN-F6
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Key command to
activate port
Key command to
de-activate port
Computer
BCC*
automatic
reboot computer
Bondwell
LCD or CRT options after
bootup
reboot for LCD or CRT
options to appear
Chaplet**
setup screen
FN-F6
setup screen
FN-F6
FN-F4
FN-F4
Chembook
Commax
FN-F6
FN-F6
Ctrl-Alt-#6
Ctrl-Alt-<
FN-F4
Ctrl-Alt-#5
Ctrl-Alt->
FN-F4
Compaq* **
automatic
mode/? (for setup option)
automatic
automatic
mode/? (for setup option)
automatic
Compuadd* **
Data General
Alt-F for screen setup
option
Alt-F for screen setup
option
Ctrl-Alt-Command
Ctrl-Alt-Command
reboot
Data General
Walkabout
2 CRT/X at DOS prompt
Datavue
DEC**
Ctrl-Shift-M
FN-F5
Ctrl-Shift-M
FN-F5
FN-F4
FN-F4
Dell**
Ctrl-Alt-<
Ctrl-Alt->
Ctrl-Alt-F10
FN-F8
Ctrl-Alt-F10
FN-F8 (CRT/LCD)
FN-D
FN-D
FN-F12
FN-F12
Digital*
automatic
reboot
FN-F2
FN-F2
Dolch
Epson
Everex*
For-A
dip switch to CRT
dip switch to CRT
setup screen option
Ctrl-Alt-Shift-C
FN-F10
dip switch to LCD
dip switch to LCD
setup screen option
Ctrl-Shift-Alt-L
Fujitsu
39
Download from Www.Somanuals.com. All Manuals Search And Download.
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Computer
Gateway
FN-F3
FN-F3
FN-F1
FN-F1/FN-F1 again simul-
taneous
Grid* **
FN-F2, choose auto or
simultaneous
FN-F2
Ctrl-Alt-Tab
Ctrl-Alt-Tab
FN-F7
Hitachi
FN-F7
Honeywell
Hyundai
FN-F10
FN-F10
setup screen option
automatic
setup screen option
warm reboot
FN-F2
IBM 970*
IBM ThinkPad**
reboot, enter setup menu
FN-F7, select choice from
setup menu
FN-F1, select choice
FN-F5, select choice
PS/2 SC select choice
(CRT, LCD, etc.)
Infotel
FN-F12
FN-F12
Kaypro
boot up, monitor plugged
in
unplug monitor
Kris Tech
FN-F8
FN-F8
FN-T
Leading Edge
FN-T
Mac Portable
100
no video port: not compatible
Mac PowerBook
140, 145, 150,
170
no video port: requires a 3rd-party interface
160, 165, 180,
520, 540, 5300
Control Panel folder, Pow- warm reboot
erBook Display folder;
Activate Video Mirroring
210, 230, 250,
270, 280, 2300
requires Apple Docking Station or Mini Dock
Magitronic
FN-F4
FN-F2
FN-F4
FN-F1
Mastersport
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Key command to
activate port
Key command to
de-activate port
Computer
Micro Express*
Micron
automatic
warm reboot
FN-F2
FN-F2
Microslate*
Mitsubishi
NCR
automatic
warm reboot
SW2 Off-On-On-On
setup screen option
setup screen option
LCD at the DOS prompt
FN-F3
SW2 On-Off-Off-Off
setup screen option
setup screen option
CRT at the DOS prompt
FN-F3
NEC* **
Olivetti*
automatic
automatic
FN-O/*
FN-O/*
Packard Bell* **
FN-F0
FN-F0
Ctrl-Alt-<
Ctrl-Alt->
Panasonic
Prostar
Samsung*
Sanyo
FN-F2
FN-F2
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to CRT
Ctrl-Shift-M
Ctrl-Alt-S at bootup
setup screen option
setup screen option
dip switch to LCD
Ctrl-Shift-M
Sharp
Sun SPARC-
Dataview
Tandy**
Ctrl-Alt-Insert
setup screen option
FN-F5
Ctrl-Alt-Insert
setup screen option
FN-F5
Tangent
Texas Instru-
ments*
setup screen option
setup screen option
Top-Link* **
setup screen option
FN-F6
setup screen option
FN-F6
Toshiba* **
Ctrl-Alt-End
FN-End
Ctrl-Alt-Home
FN-Home
FN-F5
FN-F5
setup screen option
FN-F7
setup screen option
FN-F7
Twinhead*
WinBook
FN-F5
FN-F5
Automatic
Ctrl-Alt-F10
Automatic
Ctrl-Alt-F10
41
Download from Www.Somanuals.com. All Manuals Search And Download.
A
p
p
e
n
d
i
x
Key command to
activate port
Key command to
de-activate port
Computer
Wyse
software driven
FN-F10
software driven
FN-F10
Zenith**
FN-F2
FN-F2
FN-F1
FN-F1
Zeos**
Ctrl-Shift-D
FN-F1
Ctrl-Shift-D
FN-F1
*
These manufacturers have models that automatically send video
to the external CRT port when some type of display device is
attached.
** These manufacturers offer more than one key command depend-
ing on the computer model.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Video Mirroring with a PowerBook Computer
When you turn video mirroring (called SimulScan in newer Pow-
erBooks—see below) on, the projector displays the same informa-
tion that appears on your PowerBook’s built-in screen. When
video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
1 Open the Monitors control panel; click on Monitor 2.
2 Set the number of colors you want.
3 Open the Control Strip, then click on the monitor icon.
4 Select “Turn Video Mirroring On.”
Now you can turn video mirroring on and off from the Control
Strip without having to open the Monitors control panel again.
When using video mirroring and high color graphics such as
slide shows, the projected image occasionally might turn black
and white. If this happens, perform the following steps:
1 Turn off video mirroring.
2 Open the Monitors control panel.
3 Move the white menu bar to Monitor 2 to set the projector as
the primary monitor.
4 Restart the PowerBook.
Using SimulScan
Some newer PowerBooks display images on an external monitor
or projector differently than previous ones. When using
SimulScan, the projector displays the same information that
appears on your PowerBook
To select SimulScan:
1 Open the Control Panel, then double-click Monitors and
Sound.
2 In the Resolution list, choose the SimulScan mode, then click
OK.
3 If this changes your display settings, a dialog box appears.
Click OK to confirm the change.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
A
p
p
e
n
d
i
x
Projected Image Size
NOTE: Use the graph and tables
to help you determine projected
image sizes.
FIGURE 23
Projected image size
Table 1:
Image Size, Width and Height for TDP-B1-maximum image size
Distance to
Screen (feet)
Diagonal
(feet)
Width
(feet)
Height
(feet)
4.9
8
3.2
5.2
2.6
4.2
1.9
3.1
12
16
20
30
7.8
6.3
4.7
10.4
13.0
19.5
8.3
6.3
10.4
15.6
7.8
11.7
Table 2:
Image Size, Width and Height for TDP-B1-minimum image size
Distance to
Screen (feet)
Diagonal
(feet)
Width
(feet)
Height
(feet)
4.9
8
2.5
4.1
2.0
3.3
1.5
2.5
3.7
4.9
6.2
9.2
12
16
20
30
6.2
4.9
8.2
6.6
10.3
15.4
8.2
12.3
44
Download from Www.Somanuals.com. All Manuals Search And Download.
C
cables
INDEX
audio 7
mouse 8
A
accessories, ordering 36, 37
activation commands for laptop com-
puters 38
power 36
adjusting
S-video 9, 37
brightness 19
color 20
contrast 19
tint 19
don’t match monitor colors 34
compatibility
volume 17, 20
adjusting the height of the projector 15
altitude limits 35
assistance. See Technical Support
Audio menu 20
IBM-compatible 1
Macintosh 1
connecting 9
Audio menu options
Volume 20
computers, compatible 1
Auto Source Select 24
IBM-compatible computer 7
mouse 8
B
Blank Screen 20
brightness, adjusting 19
buttons on keypad
Lamp on/off 16
Menu 16
contrast, adjusting 19
Controls menu 23
Controls menu options
Auto Source Select 24
Default Source 24
Display Messages 24
Display Startup Screen 25
Plug and Play 24
Rear Projection 24
Standby Time 23
Video Standard 23
Source 16
Standby 17
Volume 17
45
Download from Www.Somanuals.com. All Manuals Search And Download.
I
n
d
e
x
D
Default Source 24
Display menu 19
Display menu options
Blank Screen 20
Brightness 19
centering 22
Color 20
Contrast 19
focusing 15
Reset All 20
Tint 19
Display Messages 24
Display Startup Screen 25
displaying
has lines or spots 33
not centered 31
out of focus 33
quality 31–34
on-screen menus 16
startup screen 25
status messages 24
reversed 24, 33
size 5, 44
E
elevator button/foot 15
streaked 33
too wide or too narrow 32
zooming 15
F
fuzzy lines 22
Image menu 21
Image menu options
Auto Image 21
Auto Resize 21
Horiz. Position 22
Manual Sync 21
Manual Tracking 22
Vert. Position 22
K
Kensington lock 30, 37
keypad 16
46
Download from Www.Somanuals.com. All Manuals Search And Download.
L
lamp
ordering 36
Plug and Play 24
replacing 27
portable computers
turns off unexpectedly 34
compatibility 7
connecting IBM-compatible 7
power cord
lamp hour counter 26
Lamp on/off button 16
Language menu 25
language, selecting for menus 25
lens
cap 36
ordering 36
cleaning 27
M
Macintosh computers
R
compatibility 1
connecting 7
rear projection 24
remote control
Menu button 18
replacing the batteries 30
using 13, 16
menus. See on-screen menus
monitor, projected colors don’t match
34
replacing projection lamp module 27
re-positioning the image on the screen
22
mouse, connecting 8
N
NTSC video 23
O
on-screen menus
Source button 16
Standby button 17
Standby Time 23
startup screen 25
Status menu 26
Audio menu 20
changing language of 25
Controls menu 23
Display menu 19
displaying 18
Image menu 21
Language menu 25
making changes to menu
functions 18
S-video
Status menu 26
connecting 9
ordering cable 37
47
Download from Www.Somanuals.com. All Manuals Search And Download.
I
n
d
e
x
T
TDP-B1
USB mouse 8
project from behind the screen 24
setting up 5
specifications 35
VESA computer cable 7
turning off 12
turning on 11
video standards 23
Technical Support
information to have on hand
temperature limits 35
test pattern 31
Volume buttons 17
W
text not visible 31
tint, adjusting 19
warranty 37
troubleshooting 31
turning off the projector 12
turning on the projector 11
Z
zooming the image 15
48
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Toshiba Corporation (“Toshiba”) warrants that each TDP-B1 (“the Product”) sold hereunder will conform to and function
in accordance with the written specifications of Toshiba. Said limited warranty shall apply only to the first person or entity
that purchases the Product for personal or business use and not for the purpose of distribution or resale. The product may
contain recycled components that are in new condition. Said warranty shall continue for a period of two (2) years from the
date of such purchase. The standard limited warranty excludes the lamps in projectors after 90 days and the accessories
after one year. Toshiba does not warrant that the Product will meet the specific requirements of the first person or entity
that purchases the Product for personal or business use. Toshiba’ liability for the breach of the foregoing limited warranty
is limited to the repair or replacement of the Product or refund of the purchase price of the Product, at Toshiba’ sole option.
To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost
and expense, to Toshiba or to any authorized Toshiba service center provided, however, that the Product must be accompa-
nied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer’s name; and
(iii) the model and serial number of the Product. When sending your unit in for repair, please ship your unit in its original
packing material or an Toshiba approved ATA Shipping Case, or have a professional packaging company pack the unit.
Please insure your shipment for its full value. A return authorization number, issued by the Toshiba customer service
department, must also be clearly displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
Toshiba shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations,
or service other than by Toshiba or its authorized agents, causes other than from ordinary use or failure to properly use the
Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES
THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED,
ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY Toshiba.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT Toshiba’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY
WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE
PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL Toshiba BE LIABLE FOR SPE-
CIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE
PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING Toshiba’ LIABILITY. NO ACTION,
REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT
BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Number 010-0228-00
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communi-
cations. Operation of this equipment in a residential area is likely to cause harm-
ful interference in which case the user will be required to correct the interference
at his own expense.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Can-
ada.
Safety Certifications
UL, CUL, TÜV, NOM
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interfer-
ence, in which case the user may be required to take adequate measures. The typ-
ical use is in a conference room, meeting room or auditorium.
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conformity
Manufacturer: Toshiba
1-1, Shibaura 1-Chome, Minato-ku, Tokyo, Japan
We declare under our sole responsibility that the TDP-B1 Projector conforms to
the following directives and norms:
Directive 89/336/EEC, Amended by 93/68/EEC
EMI: EN 55022 (1992) Class A
EMC: EN 50082-1 (1992)
IEC 801-2, IEC 801-3, IEC 801-4
Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 1992 + A1 + A2 + A3: 1995
July, 1999
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of
Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of
International Business Machines, Inc. MicroSaver and Kensington are trademarks
or registered trademarks of Kensington Microware Limited. Microsoft, Power-
Point, and Windows are trademarks or registered trademarks of Microsoft Corpo-
ration. Digital Light Processing is a trademark or registered trademark of Texas
Instruments.
Download from Www.Somanuals.com. All Manuals Search And Download.
|