DESIGNER SERIES
BUILT-IN ELECTRIC OVENS WARRANTY
ONE YEAR FULL WARRANTY
Built-in electric ovens and all of their component parts and accessories, except as detailed below*, are warranted to be
free from defective materials or workmanship in normal household use for a period of twelve (12) months from the date
of original retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part which
fails or is found to be defective during the warranty period.
designer series
*Glass (including light bulbs), painted and decorative items are warranted to be free from defective materials or
workmanship for a period of ninety (90) days from the date of original retail purchase. ANY DEFECTS MUST BE
REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.
built-in electric wall ovens
Viking Range Corporation uses the most up-to-date processes and best materials available to produce all color finishes.
However, slight color variation may be noticed because of the inherent differences in painted parts and porcelain parts as
well as differences in kitchen lighting, product locations, and other factors.
Use and Care Manual
FIVE YEAR LIMITED WARRANTY
Any bake element, broil element, or convection cook element which fails due to defective materials or workmanship in
normal household use during the second through fifth year from the date of original retail purchase will be repaired or
replaced, free of charge for the part itself, with the owner paying all other costs, including labor.
TEN YEAR LIMITED WARRANTY
Any porcelain oven or porcelain inner door panel which rusts through due to defective materials or workmanship in
normal household use during the second through the tenth year from the date of original retail purchase will be repaired
or replaced, free of charge for the part itself, with the owner paying all other costs, including labor.
This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the
product during the term of the warranty.
This warranty shall apply to products purchased and located in the United States and Canada. Products must be
purchased in the country where service is requested. Warranty labor shall be performed by an authorized Viking Range
Corporation service agency or representative. Warranty shall not apply to damage resulting from abuse, accident,
natural disaster, loss of electrical power to the product for any reason, alteration, outdoor use, improper installation,
improper operation, or repair or service of the product by anyone other than an authorized Viking Range Corporation
service agency or representative. This warranty does not apply to commercial usage. Warrantor is not responsible for
consequential or incidental damage whether arising out of breach of warranty, breach of contract, or otherwise. Some
jurisdictions do not allow the exclusion or limitation of incidental of consequential damages, so the above limitation or
exclusion may not apply to you.
Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase
upon request, and making the appliance reasonably accessible for service. If the product or one of its component parts
contains a defect or malfunction during the warranty period, after a reasonable number of attempts by the warrantor to
remedy the defects or malfunctions, the owner is entitled to either a refund or replacement of the product or its
component part or parts. Warrantor’s liability on any claim of any kind, with respect to the goods or services covered
hereunder, shall in no case exceed the price of the goods or service or part thereof which gives rise to the claim.
WARRANTY SERVICE: Under the terms of this warranty, service must be performed by a factory authorized Viking
Range Corporation service agent or representative. Service will be provided during normal business hours, and labor
performed at overtime or premium rates shall not be covered by this warranty. To obtain warranty service, contact the
dealer from whom the product was purchased, an authorized Viking Range Corporation service agent, or Viking Range
Corporation. Provide model and serial number and date of original purchase. For the name of your nearest authorized
Viking Range Corporation service agency, call the dealer from whom the product was purchased or Viking Range
Corporation. IMPORTANT: Retain proof of original purchase to establish warranty period.
The return of the Owner Registration Card is not a condition of warranty coverage. You should, however, return the
Owner Registration Card so that Viking Range Corporation can contact you should any question of safety arise which
could affect you.
Any implied warranties of merchantability and fitness applicable to the above described bake element, broil element,
convection cook element, porcelain oven, or porcelain inner door panel are limited in duration to the period of coverage
of the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives you specific legal
rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.
Viking Range Corporation
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi (MS) 38930 USA • (662) 455-1200
Specifications subject to change without notice
For more product information, call 1-888-VIKING1 (845-4641), or visit the
F20024B
(M0703VR
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Do not heat unopened food containers; buildup of pressure may cause
the container to explode and result in injury.
Built-In Electric Oven Features
10. Always position oven racks in desired location while oven is cool. If
rack must be moved while oven is hot, do not let potholder contact
hot heating element in oven.
11. Use care when opening oven door. Let hot air or steam escape
before removing or replacing food. Hot air or steam can cause burns
to hands, face and/or eyes.
8-pASS BROIL
ELEMENT
oVEN
LIGHT
12. Keep oven vents unobstructed. The oven vent is located at the front
of the oven and vents into the room.
oVEN
LIGHT
TRUCONVECtm
ELEMENT
(BEHIND BAFFLE)
13. Do not clean door gasket. It is essential for a good tight seal. Care
should be taken not to rub, damage, or move the gasket.
OVEN
RACKS
(3/UPPER
OVEN;
2/LOWER
OVEN
14. No commercial oven cleaner or oven liner protective coating such as
aluminum foil should be used in or around any part of the oven.
Improper oven liners may result in a risk of electric shock or fire.
Keep oven free from grease buildup.
BAKE
ELEMENT
15. Before self-cleaning the oven, remove broiler pan, broiler grid, oven
racks, rack supports, and other utensils. Do not use your oven to
clean other parts. A fan noise should be heard during the cleaning
cycle If not, call service before self-cleaning again.
sELF-CLEAN
NON-
MODEL/SERIAL
NUMBER
CONVECTION
LOWER OVEN
PLATE (BEHIND
DOOR)
16. DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES
OF OVEN. Heating elements may be hot even though they are dark
in color. Interior surfaces of an oven become hot enough to cause
burns. During and after use, do not touch, or let clothing or other
flammable materials contact heating elements or interior surfaces of
oven until they have had sufficient time to cool. Other surfaces of the
oven may become hot enough to cause burns, such as the oven vent
opening, the surface near the vent opening, and the oven door
window.
-SAVE THESE INSTRUCTIONS-
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.
For "slow" broiling, allow about 4 inches between
the top surface of the food and the broil element.
"Slow" broiling is best for chicken and ham in
order to broil food without over-browning it.
Basic Functions of Your Oven
Two-Element Bake
Full power heat is radiated from the bake element
in the bottom of the oven cavity, and
Convection Broil
(upper oven only)
supplemental heat is radiated from the broil
element. This function is recommended for single
rack baking and roasting.
Exactly the same as regular broiling with
additional benefit of air circulation by the
motorized fan in the rear of the oven. The cool air
is quickly replaced-improving the already high
performance of the broil element. Especially
useful for broiling thick cuts of meat.
Convection Bake
(upper oven only)
Exactly the same as regular baking with the
additional benefit of air circulation. The heated air
is circulated by the motorized fan in the rear of the
oven. It provides more even heat distribution
throughout the oven cavity for all uses. Multiple
rack use is possible for the largest baking jobs.
When roasting, cool air is quickly replaced-searing
meats on the outside and retaining more juices
and natural flavor on the inside with less shrinkage.
Convection Dehydrate
(upper oven only)
With the selector set to convection cook and the
temperature control on 150 F, warm air is
circulated by a motorized fan in the rear of the
oven. Over a period of time, the water is
removed from the food by evaporation. Removal
of water inhibits growth of microorganisms and
retards the activity of enzymes. It is important to
remember that dehydration does not improve the
quality, so only fresh, top-quality foods should be
used.
The rear element only operates at full power.
There is no direct heat from the bottom or top
elements. Air in the oven cavity is circulated by
the fan for even heating. Use this setting for
foods which require gentle cooking such as
pastries, souffles, yeast breads, quick breads and
cakes. Use this function for single rack baking,
multiple rack baking, roasting, and preparation of
complete meals.
tm
TruConvec
(upper oven only)
Convection Defrost
(upper oven only)
With the selector set to convection cook and the
temperature control off, air is circulated by a
motorized fan in the rear of the oven. The fan
accelerates natural defrosting of the food without
heat. To avoid sickness and food waste, do not
allow defrosted food to remain in the oven for
more than two hours.
In Maxi-Broil heat is radiated from both broil
elements, located in the top of the oven cavity, at
full power. Broiling speed is determined by the
distance between the foods and the broil
elements. For "fast" broiling, food may be as
close as 2 inches to the broil element or on the
top rack. "Fast" broiling is best for meats where
"rare to medium" doneness is desired. The Mini-
Broil setting is designed for "slow" broiling. Only
the center broil element operates for partial
power.
This oven features a pyrolytic self-cleaning cycle.
During this cycle, the oven reaches elevated
temperatures in order to burn off soils and deposits.
An integral smoke eliminator reduces odors
associated with the soil burn-off. A powder ash
residue is left in the bottom of the oven after
completion of the self-clean cycle. When the oven
has cooled, remove any ash from oven surfaces with
a damp sponge or cloth.
Broil
Self-Clean
6
7
Download from Www.Somanuals.com. All Manuals Search And Download.
The time-of-day can be changed by following steps 1 through 3. It cannot
be changed while there is a Bake Hours or Start Time cycle programmed
into the timer.
Using Your Oven
Setting the MIN/SEC Timer
The MIN/SEC Timer is designed for accurate timing and is ideal for baking
delicate items such as biscuits, cookies, and popovers, and for precise
broiling. The MIN/SEC timer can be used at the same time the Bake Hours
or Start Time functions are in use. It can be used for timing up to 24 hours.
When setting the Timer, the time displayed will increase in 1 minute
increments. When the Timer counts down to 1 minute, the timer alarm will
give two short beeps and the display changes from hours:minutes to
seconds only.
Electronic Timing Center (Digital Display)
The Electronic Timing Center is used to program and control all timing
functions. Depending on the model, your unit will have a digital display or
an analog clock with digital display. If your unit has an analog clock, refer to
pages 13-16.
To program the MIN/SEC Timer
1. Press the MIN/SEC Timer button. The timer will display :00 and the
word timer will be displayed in the lower right corner.
2. Turn the Set Knob until the desired duration time is displayed.
It has five display and programming modes that are activated by the four
push buttons and the Set Knob. Both the Bake Hours mode and the
MIN/SEC Timer mode can be used to time cooking periods. These
features can even be used at the same time when both ovens are in use.
However, only Bake Hours and Self-Cleaning modes shut the oven off
automatically when the timed program is over. For example, you can time
bake a casserole in the upper oven using the Bake Hours mode, while
broiling in the lower oven using the MIN/SEC Timer. One oven can also be
cleaned while timing foods in the other oven using the MIN/SEC Timer.
The Timer is now programmed. The alarm will sound at the end of the
countdown. The program can be canceled anytime by setting the
remaining time to :00. To change back to the time-of-day, press the
CLOCK button. Notice that a small clock will be displayed in the upper
right corner to indicate that a program is in progress. The display will return
automatically to the MIN/SEC Timer after a few seconds.
Timer Alarm
Setting the Time-of-Day
At the end of a MIN/SEC Timer program or Bake Hours program, the alarm
will consist of three beeps followed by two beeps every 10 seconds until
the MIN/SEC Timer button is pressed. Whenever a valid function key is
pressed or when a control function starts automatically, one beep will be
sounded. When an invalid function key is pressed, two beeps will be
sounded.
The time-of-day must be set before any other program can be used. When
your oven is first connected to the power in your home, the timer display
will show --:--. To program the time-of-day:
1. Press the CLOCK button. 12:00 will be displayed with the word set in
the upper right corner.
2. Turn the Set Knob until the correct time-of-day is displayed. AM and PM
are not indicated.
3. Press the CLOCK button again. The word set will disappear and the
correct time is now set into the timer.
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Bake Hours Program
Setting the Automatic Start Time Bake Program
The Bake Hours program is used of controlled timing of baked or roasted
foods. At the end of the timed cycle, the oven automatically turns off.
Times in the Bake Hours mode are displayed in hours and minutes, with a
setting from 1 minute to 11 hours 50 minutes, increasing in 1 minute
increments.
The Bake Hours and Start Time modes of the Timer can be used to
automatically turn the oven on and off at a preselected time. The
Automatic Time Bake Program is ideal for foods with no danger of spoilage
during the time the oven is left off.
To set the Automatic Time Bake program
To set the Bake Hours program
1. Turn the MANUAL/TIMED knob to TIMED, UPPER TIMED OR LOWER
TIMED position, depending upon the oven mode and oven being used.
2. Set the Oven Function Selector to the BAKE, CONVECTION BAKE, or
1. Turn the MANUAL/TIMED knob to TIMED, UPPER TIMED OR LOWER
TIMED position, depending upon the oven mode and oven being used.
2. Set the Oven Function Selector to the BAKE, CONVECTION BAKE, or
TruConvec position, depending upon the type of baking being used.
3. Set the temperature Control knob to the desired temperature and allow
for preheating.
TM
TruConvec position, depending upon the type of baking being used.
TM
3. Program the Start Time by pressing the Start Time button and turning
the Set Knob until the desired Start Time is displayed. This is the time-
of-day you want the food to begin cooking.
4. Press the Bake Hours button. The Timer will display :00 with the words
set and cook in the upper right corner.
5. Turn the Set Knob until the desired baking time is displayed in hours and
minutes. The word cook will remain in the display indicating that the
Bake Hours program has been set.
4. Program the required baking time by pressing the Bake Hours button.
The words set and cook in the upper right corner. Turn the Set Knob
until the desired baking time is displayed in hours and minutes. The
word set will disappear and the word delay will remain in the display
indicating that the Bake Hours program has been set.
5. Set the Temperature Control Knob to the desired temperature.
The Timer will automatically compute a stop time and enter it into the timer
memory. The alarm will sound three beeps followed by two beeps every 10
seconds until the Bake Hours button is pressed. The duration time can be
changed anytime during the cooking program by following steps 4 and 5.
Setting the remaining duration time to :00 cancels the Bake Hours program.
To return the Timer to the present time-of-day, press the CLOCK button. A
small clock will appear in the upper right corner indicating a Bake Hours
program has been set. The Timer will go back to the Bake Hours
automatically after a few seconds.
When the specified start time is reached, the oven will automatically turn
on. The oven then bakes for the length of time programmed into the Bake
Hours mode, turn the oven off, and sounds the alarm. Setting the
remaining duration time to :00 cancels the automatic bake program.
10
11
Download from Www.Somanuals.com. All Manuals Search And Download.
To program the MIN/SEC Timer
1. Push and release the “timer” button.
2. Rotate “Set” knob until desired duration of time is displayed. Timer
starts seconds after “Set” knobs stops rotating. A tone indicates the
timer has started.
When the timer has one minute remaining, the timer will sound twice and
begin to countdown by seconds. A tone will sound three times indicating
the time is complete and twice every ten seconds after completion until
timer function is cleared.
00:00
bake
timer
start time probe
temp.
Set
hours
NOTE: Press any function button to clear a completed cycle or function.
Electronic Timing Center (Analog Clock w/Digital Display)
Setting the Bake Hours Program
Synchronizing the analog and digital clocks
Synchronizing the analog and digital clocks
1. Press the “timer” and “start time” buttons simultaneously.
2. Turn the set knob to move the hands on the analog clock to any time
setting.
The Bake Hours program is used for controlled timing of baked or roasted
foods. At the end of the timed cycle, the oven automatically turns off.
To set the Bake Hours program
3. After five seconds the display will go blank. Press the timer button and
using the set knob, set the digital time to the exact time on the analog
clock.
1. Turn the MANUAL/TIMED knob to TIMED, UPPER TIMED OR LOWER
TIMED position, depending upon the oven mode and oven being used.
2. Set the Oven Function Selector to the BAKE, CONVECTION BAKE, or
TruConvec position, depending upon the type of baking being used.
3. Set the temperature Control knob to the desired temperature and allow
for preheating.
4. Press and release the Bake Hours button. The Timer will display :00 with
the words set and cook in the upper right corner of the digital display.
5. Turn the Set Knob until the desired baking time is displayed in hours and
minutes. The cook time/remaining time and “Cook” will be displayed.
TM
This will synchronize the two clocks. You can now set the time of day.
Setting the Time-of-Day
The time-of-day must be set before any other program can be used. When
your oven is first connected to the power in your home, the digital display
will show 00:00. To program the time-of-day:
1. Push and hold the “timer” and “bake hours” button at the same time.
2. Turn the “Set” knob until correct time is displayed on the digital clock.
3. Release “timer” and “bake hours” button
“Cook” will flash and the tone will sound three times when the time is
completed; oven will turn off. The tone will sound twice every ten seconds
after completion until timer function is cleared.
The analog clock will automatically set after the digital time is set.
Setting the MIN/SEC Timer
The MIN/SEC Timer is designed for accurate timing and is ideal for baking
delicate items such as biscuits, cookies, and popovers, and for precise
broiling. The MIN/SEC timer can be used at the same time the Bake Hours
or Start Time functions are in use. It can be used for timing up to 24 hours.
12
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting the Automatic Start Time Bake Program
Probe function
The “bake hours” and “start time” modes of the Timer can be used to
automatically turn the oven on and off at a preselected time. The
Automatic Time Bake Program is ideal for foods with no danger of spoilage
during the time the oven is left off.
The meat probe takes the guesswork our of roasting by cooking foods to
the ideal internal temperature. The “probe temp.” setting is used to
automatically turn the oven off when the internal temperature of the meat
being roasted is reached.
To set the Automatic Time Bake program
To set the automatic probe function
1. Turn the MANUAL/TIMED knob to TIMED, UPPER TIMED OR LOWER
TIMED position, depending upon the oven mode and oven being used.
2. Set the Oven Function Selector to the BAKE, CONVECTION BAKE, or
1. Insert the probe into the meat and slide into oven.
2. Plug the probe into the outlet located on left interior wall of the oven
and close the oven door.
TM
TruConvec position, depending upon the type of baking being used.
3. Press and release the “probe temp.” button.
3. Press and release “start time”. Turn the “Set” knob to desires start time.
4. Press and release “bake hours” button. Turn the “Set” knob until
desired duration of cooking time is reached. “Delay” will be displayed
in the upper left corner of the digital display during the delay cycle.
Once the bake cycle begins, the cook time/remaining time and “Cook”
will be displayed.
4. Turn the “Set” knob to the desired internal temperature. “Probe” and
the desired internal temperature will be displayed to the lower right of
the analog clock. NOTE: It is recommended to set the internal
temperature about 10 degrees lower than actual desired internal
temperature. The meat will continue to cook when removed from the
oven and will reache desired internal temperature while “standing”.
When the specified start time is reached, the oven will automatically turn
on. The oven then bakes for the length of time programmed into the Bake
Hours mode, turn the oven off, and sounds the alarm. “Cook” will flash
and the tone will sound three times when the time is completed; oven will
turn off. The tone will sound twice every ten seconds after completion until
timer function is cleared.
“Probe” flashes, tone sounds three times, and oven shuts off when desired
temperature is reached. The tone will sound twice every ten seconds after
completion until probe function is closed.
NOTE: If the “bake hours” button is not pressed within ten seconds of
setting the “start time”, the user will automatically be prompted to enter
the “bake hours”. A tone will sound twice every five seconds until the
“bake hours” is entered.
14
15
Download from Www.Somanuals.com. All Manuals Search And Download.
•MAXI-BROIL
WARNING
: To avoid sickness and food waste when using automatic
time baking:
The top element operates at full power. Use this setting for broiling small
and average cuts of meats.
-Do not use foods that will spoil while waiting for cooking to start, such as
dishes with milk or eggs, cream soups, custards, fish, pork, poultry, or foods
with stuffing.
-Any food that has to wait for cooking to start should be very cold or
frozen before it is placed in the oven.
-Do not use foods containing baking powder or yeast when automatic
time baking. They will not rise properly.
-Do not allow food to remain in the oven for more than two hours after the
end of the cooking cycle.
•MINI-BROIL
Only the center broil element operates for partial power. This setting is
designed for small amounts of food and "slow" broiling.
•CONVECTION BROIL (upper oven only)
The top element operates at full power. Air in the oven cavity is circulated
by the fan for even heating. Use this setting for broiling thick cuts of
meats.
•SELF-CLEAN
The self-clean cycle is designed to eliminate the need for scrubbing and
scouring food baked onto the oven interior. The self-clean cycle heats
these soils to a high temperature in which the baked on food is burned off.
OVEN FUNCTION SELECTOR
Each oven has a separate oven function selector. There are seven
settings on each selector.
•BAKE:
The bottom element operates at full power, and the top broil element
operates at supplemental power. Use this setting for baking, roasting, and
casseroles.
TEMPERATURE CONTROL
Each oven has a separate temperature control dial. The controls can be set
•CONVECTION BAKE (upper oven only)
o
o
at any temperature from 150 F to 550 F. There are separate settings for
broiling and self-cleaning. Always be sure the controls are in the OFF
position when the ovens are not in use.
The bottom element operates at full power, and the top broil element
operates at supplemental power. Air in the oven cavity is circulated by the
fan for even heating. Use this setting for baking and roasting.
tm
•TruConvec (upper oven only)
The rear element only operates at full power whenever heating. There is no
direct heat from the top or bottom elements. Air in the oven cavity is
circulated by the fan for even heating. Use this setting for foods which
require gentle cooking such as pastries or soufflés, and for baking yeast
breads and cakes. This setting is also recommended when baking large
quantities of baked goods at one time.
INTERIOR OVEN LIGHT CONTROL
The upper and lower ovens have interior oven lights that are controlled by
separate switches on the control panel. Push the switch to turn the interior
oven lights on and off.
16
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Rack Positions
TWO ELEMENT BAKING/
Each oven is equipped with three tilt-proof racks. All ovens have six rack
positions. Position 6 is the farthest from the oven bottom. Position 1 is the
closest to the oven bottom. The racks can be easily removed and arranged
at various levels. For best results with conventional baking, do not use
more than one rack at a time. It is also recommended, when using two
racks, to bake with the racks on positions 2 and 4 or positions 3 and 5.
CONVECTION BAKING / CONVECTION COOKING
Preheating
Preheating the oven is not necessary when using temperatures below 250 F.
For best results, it is extremely important that you preheat the oven when
baking cakes and other items that have critical baking temperatures. After
the temperature control has been set, the Oven Indicator light goes out
when the oven reaches that temperature. Preheating takes no longer than
10 -15 minutes. Preheat times will be greater in those areas in which the
electrical supply is less than 240 volts.
Two Element Baking
Position 6
Position 5
Position 4
Position 3
Position 2
Position 1
Conventional baking/roasting is particularly suitable for dishes which require
a high temperature. Many cookbooks contain recipes to be cooked in the
conventional manner. This bake setting is only recommended for single
rack baking.
Convection Baking (upper oven only)
Convection baking is the process of cooking food with a flow of heated air
circulating throughout the oven cavity. The even circulation of this air
equalizes the temperature throughout the oven cavity and eliminates the
hot and cold spots found in conventional ovens. This feature can make a
significant difference in foods prepared in the oven. A major benefit of
convection baking is the ability to prepare food in quantity. The uniform air
circulation makes this possible . . . a feature not possible in a standard oven.
With this heating system, the air is distributed evenly throughout the oven
by the convection fan. The heat therefore reaches the food to be baked or
roasted more quickly. With this heating method, foods can be baked and
roasted at the same time with minimal taste transfer, even when different
dishes are involved, such as cakes, fish or meat. The hot air system is
especially economical when thawing frozen food.
To Bake:
1. Arrange the oven racks in the desired positions BEFORE heating the
oven. If cooking on two racks at the same time, use rack positions 2 and
4 or positions 3 and 5.
2. Turn the Oven Function selector to desired function. Cooking starts
immediately and stops when the Oven Function selector is turned to
OFF.
TRUCONVECtm (upper oven only)
tm
In TruConvec cooking, the rear element only operates at full power. There
3. Set the Temperature Control to the desired temperature.
4. Place the food in the oven after the Oven Indicator light goes out.
is no direct heat from the bottom or top elements. The heated air is
circulated by the motorized fan in the rear of the oven. Breads, cookies,
and other baked goods come out evenly textured with golden crusts. No
special bakeware is required.
18
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Pan Placement Tips
4. Do not open the door frequently during baking. Look through the door
window to check doneness whenever possible. If you must open the
door, the best time is during the last quarter of the baking time.
5. Bake to the shortest time suggested and check for doneness before
adding more time. For baked goods, a stainless steel knife placed in the
center of the product should come clean` when done.
•When using large (15" x 13") flat pans or trays that cover most of the
rack, rack positions 2 or 3 produce the best results.
•When baking on more than one rack, it is recommended to use one of
the convection modes and the 2nd and 4th position or the 3rd and 5th
position for more even baking. When baking on three racks, use any
combination of positions 2,3, 4, and 5 for more consistent results.
•Stagger pans in opposite directions when two racks and several pans are
used in
6. Use the pan size and type recommended by the recipe to ensure best
results. Cakes, quick breads, muffins, and cookies should be baked in
shiny, reflective pans for light, golden crusts. Avoid the use of old,
darkened pans. Warped, dented, stainless steel and tin-coated pans
heat unevenly and will not give uniform baking results.
conventional bake.
If possible, no pan
should be directly
above another.
•Allow 1½ to 2
inches of air space
around all sides of
each pan for
Multiple Rack Baking
A major benefit of convection cooking is the ability to prepare foods in
quantity. The uniform air circulation makes this possible. Foods that can be
prepared on two or three racks at the same time include: pizza, cakes,
cookies, biscuits, muffins, rolls, and frozen convenience foods.
even air circulation.
For 3 rack baking, use any combination of rack positions 2, 3, 4, and 5.
Remember that the racks are numbered from bottom to top. For 2 rack
baking, use rack positions 2 and 4 or positions 3 and 5.
baking Tips
Because of variations in food density, surface texture and consistency, some
foods may be prepared more successfully using the conventional bake
setting. For this reason, conventional baking is recommended when
preparing baked goods such as custard. The user may find other foods that
are also prepared more consistently in conventional bake. This is perfectly
normal.
1. As a general rule, to convert conventional recipes to convection recipes,
reduce the temperature by 25 F and the cooking time by approximately
10 to 15%.
2. Some recipes, especially those that are homemade, may require
adjustment and testing when converting from standard to convection
modes. If unsure how to convert a recipe, begin by preparing the recipe
in conventional bake. After achieving acceptable results, follow the
convection guidelines listed for the similar food type. If the food is not
prepared to your satisfaction during this first convection trial, adjust only
one recipe variable at a time (cooking time, rack position, or
temperature) and repeat the convection test. Continue adjusting one
recipe variable at a time until satisfactory results are achieved.
3. Make sure the oven racks are in the desired position before you turn the
oven on.
20
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventional Baking Chart
Convection Baking Chart
o
o
FOOD
PAN SIZE
SINGLE
RACK POS.
TEMP( F)
TIME
(MIN)
FOOD
PAN SIZE
MULTI-
RACK POS.
TEMP( F)
TIME
(MIN)
BREADS
BREADS
Biscuits
Cookie Sheet 3 or 4
Loaf Pan 3 or 4
Cookie Sheet 3 or 4
400
375
400
375
400
350
375
375
8 - 10
30 - 35
12 - 15
30 - 35
20 - 25
35 - 40
15 - 20
15 - 20
Biscuits
Cookie Sheet 2 & 4
Loaf Pan 2 & 4
Cookie Sheet 2 & 4
375
350
375
350
375
325
350
350
7 - 9
Yeast Loaf
Yeast Rolls
Nut Bread
Cornbread
Gingerbread
Muffins
Yeast Loaf
Yeast Rolls
Nut Bread
Cornbread
Gingerbread
Muffins
20 - 25
11 - 13
20 - 25
15 - 20
30 - 35
12 - 15
10 - 12
Loaf Pan
8" x 8"
3 or 4
3 or 4
3 or 4
3 or 4
3 or 4
Loaf Pan
8" x 8"
2 & 4
2 & 4
2 & 4
2 & 4
2 & 4
8" x 8"
8" x 8"
Muffin Tin
Muffin Tin
Muffin Tin
Muffin Tin
Corn Muffins
Corn Muffins
CAKES
CAKES
Angel food
Bundt
Cupcakes
Layer, Sheet
Layer, Two
Pound
Tube pan
Tube pan
Muffin pan
13" x 9"
9" round
Loaf pan
3 or 4
3 or 4
3 or 4
3 or 4
3 or 4
3 or 4
375
350
350
350
350
350
35 - 45
45 - 55
16 - 20
40 - 50
30 - 35
60 - 65
Angel food
Bundt
Cupcakes
Layer, Sheet
Layer, Two
Pound
Tube pan
Tube pan
Muffin pan
13" x 9"
9" round
Loaf pan
3 or 4
3 or 4
2 & 4
2 & 4
2 & 4
2 & 4
325
325
325
325
325
325
30 - 35
35 - 40
15 - 17
30 - 32
25 - 30
45 - 50
COOKIES
Brownies
Choc. Chip
Sugar
COOKIES
Brownies
Choc. Chip
Sugar
13" x 9"
Cookie Sheet 3 or 4
Cookie Sheet 3 or 4
3 or 4
350
375
350
25 - 30
12 - 15
10 - 12
13" x 9"
Cookie Sheet 2,3,& 4
Cookie Sheet 2,3,& 4
2 & 4
325
350
325
20 -25
7 -10
9 -10
PASTRY
PASTRY
Cream Puffs
Cookie Sheet 3 or 4
400
30 - 35
Cream Puffs
Cookie Sheet 2 & 4
375
24 - 27
PIES
PIES
Crust, Unfilled 9" Round
3 or 4
3 or 4
425
375
10 - 12
55 - 60
Crust, Unfilled 9" Round
2 & 4
2 & 4
400
350
7 - 9
50 - 55
Crust, Filled
Lemon
9" Round
Crust, Filled
Lemon
9" Round
Meringue
Pumpkin
Custard
9" Round
9" Round
6 - 4oz cups
3 or 4
3 or 4
3 or 4
350
350
350
12 - 15
40 - 45
35 - 40
Meringue
Pumpkin
Custard
9" Round
9" Round
6 - 4oz cups
2 & 4
2 & 4
2 & 4
325
325
325
4 - 5
35 - 45
30 - 35
22
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventional Baking Chart
Convection Baking Chart
o
o
FOOD
PAN SIZE
SINGLE
RACK POS.
TEMP( F)
TIME
(MIN)
FOOD
PAN SIZE
SINGLE
RACK POS.
TEMP( F)
TIME
(MIN)
ENTREES
Egg Rolls
Fish Sticks
Lasagna, frz
Pot Pie
ENTREES
Egg Rolls
Fish Sticks
Lasagna, frz
Pot Pie
Cookie Sheet 3 or 4
Cookie Sheet 3 or 4
Cookie Sheet 3 or 4
Cookie Sheet 3 or 4
400
425
375
400
12 - 15
18 - 21
65 - 70
35 - 40
Cookie Sheet 2 & 4
Cookie Sheet 2 & 4
Cookie Sheet 2 & 4
Cookie Sheet 2 & 4
375
400
350
375
8 - 10
13 - 16
60 - 65
10 - 12
Gr. Peppers
Stuffed
Quiche 9"
Pizza, 12"
Gr. Peppers
Stuffed
Quiche 9"
Pizza, 12"
13" x 9"
Round
Cookie Sheet 3 or 4
3 or 4
3 or 4
375
400
400
65 - 70
25 - 30
15 - 20
13" x 9"
Round
Cookie Sheet 2 & 4
2 & 4
2 & 4
350
375
375
45 - 50
20 - 25
10 - 12
VEGETABLES
Macaroni
VEGETABLES
Macaroni
& Cheese, frz Cookie Sheet 3 or 4
375
375
60 - 65
60 - 65
& Cheese, frz Cookie Sheet 2 & 4
350
350
45 - 50
45 - 50
Baked Potatoes On Rack
3 or 4
Baked Potatoes On Rack
2 & 4
Spinach
Souffle
Squash
1 qt.
Casserole
Cookie Sheet 3 or 4
Cookie Sheet 3 or 4
Spinach
Souffle
Squash
1 qt.
Casserole
Cookie Sheet 2 & 4
Cookie Sheet 2 & 4
3 or 4
350
375
425
45 - 50
50 - 55
15 - 20
2 & 4
325
350
400
35 - 40
40 - 45
10 - 15
French Fries
French Fries
24
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Conventional / Convection Roasting Tips
Always use the broiler pan and grid supplied with each oven. The hot air
must be allowed to circulate around the item being roasted. Do not cover
what is being roasted. Convection roasting seals in juices quickly for a
moist, tender product. Poultry will have a light, crispy skin and meats will
be browned, not dry or burned. Cook meats and poultry directly from the
refrigerator. There is no need for meat or poultry to stand at room
temperature.
Solving Baking Problems
Baking problems can occur for many reasons. Check the Baking Problem
chart for the causes and recommended remedies for the most common
problems. It is important to remember that the temperature setting and
cooking times you are accustomed to using with your previous oven may
vary slightly from those required with this oven. If you find this to be true, it
is necessary for you to adjust your recipes and cooking times accordingly.
1. As a general rule, to convert conventional recipes to convection recipes,
reduce the temperature by 25 F and the cooking time by approximately
10 to 15%.
2. Always roast meats fat side up in a shallow pan using a roasting rack.
No basting is required when the fat side is up. Do not add water to the
pan as this will cause a steamed effect. Roasting is a dry heat process.
3. Poultry should be placed breast side up on a rack in a shallow pan.
Brush poultry with melted butter, margarine, or oil before and during
roasting.
COMMON BAKING PROBLEM / REMEDIES
PROBLEM
CAUSE
REMEDY
Cakes burn on the sides
or not done in center
1. Oven was too hot
2. Wrong pan size
3. Too many pans
1. Batter too thick
1. Reduce temperature
2. Use recom. pan size
3. Reduce no. of pans
1. Follow recipe
Cakes crack on top
Cakes are not level
Add liquid
2. Oven too hot
3. Wrong pan size
1. Batter uneven
2. Reduce temperature
3. Use recom. pan size
1. Distribute batter even
4. For convection roasting, do not use pans with tall sides as this will
interfere with the circulation of heated air over the food.
2. Oven or rack not level 2. Level oven or rack
3. Pan was warped
1. Oven door opened
too often.
3. Use proper pan
1. Use door window to
check food.
5. When using a meat thermometer, insert the probe halfway into the
center of the thickest portion of the meat. (For poultry insert the
thermometer probe between the body and leg into the thickest part of
the inner thigh.) The tip of the probe should not touch bone, fat, or
gristle to ensure an accurate reading. Check the meat temperature
halfway through the recommended roasting time. After reading the
thermometer once, insert it ½ inch further into the meat, then take a
second reading. If the second temperature registers below the first,
continue cooking the meat.
6. Roasting times always vary according to the size, shape and quality of
meats and poultry. Less tender cuts of meat are best prepared in the
conventional bake setting and may require moist cooking techniques.
Remove roasted meats from the oven when the thermometer registers 5
to 10 F lower than the desired doneness. The meat will continue to
cook after removal from the oven. Allow roasts to stand 15 to 20
minutes after roasting in order to make carving easier.
Food too brown on
bottom
2. Dark pans being used 2. Use shiny pans.
3. Incorrect rack pos.
4. Wrong bake setting
3. Use recom. rack pos.
4. Adjust to conventional
or convection setting
as needed.
5. Pan too large
5. Use proper pan
Food too brown on
top
1. Rack position too high 1. Use recom. rack pos.
2. Oven not preheated
3. Sides of pan too high
1. Hot cookie sheet
2. Allow oven to preheat
3. Use proper pans
1. Allow sheet to cool
between batches
Cookies too flat
Pies burn around edges
1. Oven too hot
2. Too many pans used
3. Oven not preheated
1. Reduce temperature
2. Reduce no. of pans
3. Allow oven to preheat
Pies too light on top
1. Oven not hot enough 1. Increase temperature
2. Too many pans used
3. Oven not preheated
2. Reduce no. of pans
3. Allow oven to preheat
7. If using a cooking bag, foil tent, or other cover, use the conventional
bake setting rather than either convection setting.
26
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the meat probe (analog clock model)
Conventional Roasting Chart
FOOD
PAN SIZE
OVEN
TIME
INTERNAL
For many foods, especially roasts and poultry, internal food temperature is
the best test for doneness. The meat probe takes the guesswork out of
roasting by cooking foods to the exact doneness you want. NOTE:
Double oven models have a probe in the upper oven only.
o
o
TEMP( F)
(min/lb)
TEMP( F)
BEEF
Rib Roast
•Rare
4 - 6
325
25
30
140
155
•Medium
•Well done
Use of probes other than the one
provided with this product may
Cable
40
170
result in damage to the probe.
Use the handles of the probe and
plug when inserting and removing
them from the meat and outlet.
Plug
Rump Roast
•Medium
•Well done
4 - 6
3 - 4
325
325
Probe
25
30
155
170
Handles
•To avoid damaging your probe, do not use tongs to pull on the cable
when removing.
•To avoid breaking the probe, make sure food is completely defrosted
before inserting.
Tip Roast
•Medium
•Well done
35
40
155
170
•To prevent possible burns, do not unplug the probe from the outlet until
the oven has cooled.
•Never leave the probe inside the oven during a self-cleaning cycle.
•Do not store the probe in the oven.
LAMB
Lamb Leg
3 - 5
325
30
35
180
PORK
Pork Loin
Pork Chops
1" thick
3 - 5
325
350
180
After preparing the meat and placing on broiler pan, follow these steps for
proper probe placement.
1. Lay the probe on the outside of the meat along
the top or side and mark with your finger where
the edge of the meat comes to on the probe.
1 - 1¼
55 - 60
Total Time
N/A
Ham, fully
Cooked
5
325
18
130
The point should rest in the center of the thickest
meaty part of the roast.
POULTRY
Chicken,
Whole
Turkey,
Unstuffed
Turkey,
Turkey,
Stuffed
Turkey,
2. Insert the probe completely into the meat. It
should not touch the bone fat or gristle. For roasts with no bone, insert
the probe into the meatiest part of the roast. For bone-in ham or lamb,
insert the probe into the center of the lowest large
muscle or joint. Insert the probe into the meatiest
part of the inner thigh from below and parallel to the
leg of a whole turkey.
3-4
375
30
180
12 - 16
20 - 24
325
325
16 - 20
16 - 20
180
180
12 - 16
325
17 - 21
180
3. When setting the probe temperature, it is
recommended to set the temperature about 10 degrees lower
than desired internal temperature. The meat will continue to cook when
removed from the oven and will reach the desired while “standing”.
Stuffed
Turkey Breast
20 - 24
4 - 6
325
325
17 - 21
20
180
180
28
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Convection Roasting Chart
Conventional Broiling
FOOD
PAN SIZE
OVEN
TIME
(min/lb)
INTERNAL
o
o
TEMP( F)
TEMP( F)
Broiling is a dry-heat cooking method using direct or radiant heat. It is used
for small individualized cuts such as steaks, chops, and patties. Broiling is
most successful for cuts of meat 1-2 inches thick. Conventional broiling is
also more suitable for flat pieces of meat. Your oven contains a top broil
element to provide additional flexibility for broiling foods such as "stuffed
lobster" and for top browning casseroles, meringues, etc. Broiling speed is
determined by the distance between the food and the broil element. On
regular conventional broiling, heat is radiated from both broil elements at
full power. For "fast" broiling, food may be as close as 2 inches to the broil
element. "Fast" broiling is best for meats where "rare to medium"
doneness is desired. The mini-broil setting is designed for "slow" broiling.
Only the center broil element operates for partial power. For "slow"
broiling, allow about 4 inches between the top surface of the food and the
broil element. "Slow" broiling is best for chicken and ham in order to broil
food without over browning it.
BEEF
Rib Roast
•Rare
•Medium
•Well done
4 - 6
325
20
24
30
140
155
170
Rump Roast
•Medium
•Well done
4 - 6
3 - 4
325
325
20
24
155
170
Tip Roast
•Medium
•Well done
30
35
155
170
LAMB
Lamb Leg
3 - 5
325
30
30
180
Convection Broiling (upper oven only)
PORK
Convection broiling has the advantage of broiling food slightly quicker than
conventional. Convection broiling of meats produces better results
especially for thick cuts. The meat sears on the outside and retains more
juices and natural flavor inside with less shrinkage.
Pork Loin
Pork Chops
1" thick
3 - 5
325
325
180
1 - 1¼
45 - 50
Total Time
N/A
Ham, fully
Cooked
To Use Maxi-Broil:
325
15
130
1. Arrange the oven rack in the desired position before turning broiler on.
2. Center the food on cold broiler pan and grid supplied with your oven.
Place broiler pan in oven.
3. Set the Oven Function Selector to Maxi-Broil and the Temperature
Control knob to Broil.
4. Close the door. With open door broiling the broil element does not
cycle on and off. With closed door broiling the broil element might
cycle on and off if an extended broiling time is required. A built-in
smoke "eliminator" in the top of the oven helps reduce smoke and
odors.
POULTRY
Chicken,
Whole
Turkey,
Unstuffed
Turkey,
Unstuffed
Turkey,
Stuffed
Turkey,
3-4
350
325
325
325
25
11
11
180
180
180
180
180
12 - 16
20 - 24
12 - 16
9 - 10
To Use Mini-Broil:
Stuffed
Turkey Breast
20 - 24
4 - 6
325
325
9 - 10
20
Follow same steps as listed above except set the Oven Function Selector to
Mini-Broil.
30
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Broiling Tips
•Always use a broiler pan and grid for broiling. They are designed to
provide drainage of excess liquid and fat away from the cooking surface to
help prevent splatter, smoke, and fire.
Broiling Chart
Type and Cut Weight
of Meat
Setting
Rack
5
Time(mins.)
•To keep meat from curling, slit fatty edge.
•Brush chicken and fish with butter several times as they broil to prevent
drying out. To prevent sticking, lightly grease broiler tray.
•Broil on first side for slightly more than half the recommended time,
season, and turn. Season second side just before removing.
•Always pull rack out to stop position before turning or removing food.
•Use tongs or a spatula to turn meats. Never pierce meat with a fork, as
this allows the juices to escape.
•Remove the broiler pan from the oven when you remove the food.
Drippings will bake onto the pan if it is left in the heated oven after
broiling. While pan is hot, place damp paper towel over grid. Drizzle with
liquid dishwashing detergent and pour water over grid. This will make
cleaning of the pan easier, or the broiler pan can be lined with aluminum
foil to make cleaning easier. Be sure the foil extends up the side of the
pan. Although it is not recommended, the grid can also be covered with
foil. Be sure to slit openings to conform with the openings in the grid so
melted fat can drain through to prevent spattering, smoking, or the
possibility of grease fire.
BEEF
Sirloin, 1"
•Rare
12 oz
Conventional Broil
7
9
11
•Medium
•Well done
T-Bone, ¾"
•Rare
10 oz.
Conventional Broil
Convection Broil
5
5
5
7
9
•Medium
•Well done
Hamburger, ½" ¼ lb.
•Rare
•Medium
4
7
9
•Well done
CHICKEN
Bnls Breast
Bone-in Breast 2 - 2½ lb.
Chicken pieces 2 - 2½ lb.
1 lb.
Convection Broil
Conventional Broil
Convection Broil
4
4
4
18
20
18 (min/lb)
HAM
Ham slice, 1"
1 lb.
Conventional Broil
4
22
LAMB
Rib Chops, 1" 12 oz.
Convection Broil
Convection Broil
5
5
7
6
Shoulder
1 lb.
PORK
Loin Chops,¾" 1 lb.
Bacon
Convection Broil
Conventional Broil
4
4
14
6
FISH
Salmon Steak 1 lb.
Convection Broil
Convection Broil
5
5
7
6
Fillets
1 lb.
32
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Oven Surfaces
Convection Dehydrate (upper oven only)
Several different finishes have been used in your electric oven. Cleaning
instructions for each surface are given below. Your oven features a Self-
Clean cycle for the oven interior. See pages 33 through 35 for complete
instructions.
NEVER USE AMMONIA, STEEL WOOL PADS OR ABRASIVE CLOTHS,
CLEANSERS, OVEN CLEANERS, OR ABRASIVE POWDERS. THEY CAN
PERMANENTLY DAMAGE YOUR OVEN.
This oven is designed not only to cook, but also to dehydrate fruits and
vegetables.
•Prepare the food as recommended
•Arrange the food on drying racks. (Not included with the oven;
Contact a local store handling speciality cooking utensils.)
•Set the appropriate "low" temperature and turn the convection fan on.
Convection Defrost (upper oven only)
meat Probe
•Place the frozen food on a baking sheet.
•Set the temperature control "OFF".*
•Turn the convection fan on.
The meat probe may be cleaned with soap and water or a soap-filled
scouring pad. Cool the probe before cleaning. Scour stubborn spots with
a soap-filled scouring pad, rinse and dry.
*IMPORTANT -
Do not turn the temperature control on. Turning
the convection fan on will accelerate the natural defrosting of the food
without the heat.
•Do not immerse the meat probe in water.
•Do not store the probe in the oven.
Stainless Steel Parts
All stainless steel body parts should be wiped regularly with hot soapy
water at the end of each cooling period and with a liquid cleaner designed
for that material when soapy water will not do the job. Do not use steel
wool, abrasive cloths, cleansers, or powders. If necessary to scrape stainless
steel to remove encrusted materials, soak the area with hot towels to loosen
the material, then use a wooden or nylon spatula or scraper. Do not use a
metal knife, spatula, or any other metal tool to scrape stainless steel. Do
not permit citrus or tomato juice to remain on stainless steel surface, as citric
acid will permanently discolor stainless steel. Wipe up any spills
immediately.
WARNING
:
To avoid sickness and food waste, do not allow defrosted food to remain in
the oven for more than two hours.
Cleaning and Maintenance
Any piece of equipment works better and lasts longer when
maintained properly and kept clean. Cooking equipment is no exception.
Your oven must be kept clean and maintained properly.
Control Knobs
MAKE SURE ALL THE CONTROL KNOBS POINT TO THE OFF POSITION
BEFORE REMOVING. Pull the knobs straight off. Wash in detergent and
warm water. Dry completely and replace by pushing firmly onto stem.
Brass Parts
CAUTION: All special ordered brass parts are coated with an epoxy
coating. DO NOT USE BRASS CLEANERS OR ABRASIVE CLEANERS ON
ANY BRASS PARTS. All brass body parts should be wiped regularly with
hot soapy water. When hot soapy water will not do the job, use every day
household cleaners that are not abrasive.
Broiler Pan and Grid
Clean with detergent and hot water. For stubborn spots, use a soap-filled
steel wool pad.
Oven Racks
Clean with detergent and hot water. Stubborn spots can be scoured with a
soap-filled steel wool pad. DO NOT CLEAN THE OVEN RACKS OR RACK
SUPPORT USING THE SELF-CLEAN CYCLE. They could sustain damage
due to the extreme heat of the Self-Clean cycle.
34
35
Download from Www.Somanuals.com. All Manuals Search And Download.
To start the Self-Clean cycle:
CAUTION:
1. Close the door completely.
Do not touch the exterior portions of the oven after self-cleaning cycle has
begun, since some parts become extremely hot to the touch! During the
first few times the self-cleaning feature is used, there may be some odor
and smoking from the "curing" of the binder in the high-density insulation
used in the oven. When the insulation is thoroughly cured, this odor will
disappear. During subsequent self-cleaning cycles, you may sense an odor
characteristic of high temperatures. Keep the kitchen well-vented during
the self-cleaning cycle.
2. Turn the oven selector knob clockwise to the self-clean mode.
3. Turn the temperature control knob past the clean setting until the knob
stops. At this time, the clean indicator light will come on. Within 30
seconds the automatic door latch engages and the oven indicator light
comes on. The oven indicator light will remain on until the oven reaches
the self-clean temperature and will then cycle on and off during the self-
clean cycle. When the oven reaches the elevated temperature needed
for self-clean, the door lock indicator light comes on.
4. The door lock indicator light will remain on until the self-clean is
completed or interrupted and the oven temperature drops to a safe
temperature. A complete cycle is approximately 3 1/2 hours with an
additional 30 minutes needed for the oven to cool down enough for the
door latch to disengage.
5. When the cycle is completed, turn both the oven selector and
temperature control knob to the off position. When the oven has
completely cooled, open door and remove any ash from the oven
surfaces with a damp cloth.
Self-Clean Cycle
This oven features an automatic pyrolytic self-cleaning cycle. During this
cycle, the oven reaches elevated temperatures in order to burn off soil and
deposits. An integral smoke eliminator helps reduce odors associated with
the soil burn-off. A powder ash residue is left in the bottom of the oven
after completion of the Self-Clean cycle. The door latch is automatically
activated after selecting the Self-Clean setting. The latch ensures that the
door cannot be opened while the oven interior is at clean temperatures.
WARNING: Do not use commercial oven cleaners inside the oven.
Use of these cleaners can produce hazardous fumes or can damage the
porcelain finishes. Do not line the oven with aluminum foil or other
materials. These items can melt or burn during a self-clean cycle, causing
permanent damage to the oven.
To stop the self-clean cycle:
To cancel or interrupt the self-cleaning cycle, turn both the temperature
control knob and the oven function selector knob to "OFF". When the
oven temperature drops to a safe temperature, the automatic door latch will
release and the oven door can be opened. When the oven has completely
cooled, remove any ash from the oven surfaces with a damp sponge or
cloth.
WARNING
Burn or Electrical Shock Hazard
Make sure all controls are OFF and oven is COOL before cleaning.
Failure to do so can result in burns or electrical shock.
Replacing Interior Oven Lights
CAUTION: DISCONNECT THE ELECTRIC POWER AT THE MAIN
FUSE OR CIRCUIT BREAKER BEFORE REPLACING BULB.
Before starting the Self-Clean cycle:
1. Remove the oven racks, rack supports, and any other items/utensils
from the oven. The high heat generated during the cleaning cycle can
discolor, warp, and damage these items. Do not use foil or liners in the
oven. During the Self-Clean cycle foil can burn or melt and damage the
oven surface.
2. Wipe off any large spills from the oven bottom and sides. Never use
oven cleaners inside a self-cleaning oven or on raised portions of the
door.
1. Unscrew glass light cover.
2. Use an oven mitt during bulb removal to
protect your hand in case the bulb breaks.
3. Replace the bulb with a 120 volt, 40 watt
appliance bulb.
3. Some areas of the oven must be cleaned by hand before the cycle
begins. Soils in these areas will be baked on and very difficult to clean if
not removed first. Clean the door up to the gasket, the door frame, and
up to 2 inches inside the frame with detergent and hot water. Rinse
4. Replace the light cover.
5. Reconnect power at the main fuse or circuit
breaker
thoroughly and dry.
36
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing Interior Halogen Lights
(Analog Models)
Do not touch bulb with bare hands. Clean any signs of oil off of the
bulb and handle with a soft cloth.
Service Information
If your oven should fail to operate:
1. Is the electrical cord securely inserted into the electrical outlet?
2. Is the circuit breaker open, or is fuse blown?
Glass light cover
If service is required:
1. Unsnap glass light cover at opposite
end from metal hinge.
Metal
hinge
1. Call your dealer or authorized service agency. The name of the
authorized service agency can be obtained from the dealer or distributor
in your area.
2. Have the following information readily available:
a. Model number
b. Serial number
c. Date of purchase
d. Name of dealer from whom purchased
3. Clearly describe the problem that you are having.
2. Firmly grasp light bulb and pull out.
3. Replace with a 64405, 12V-5W bulb.
4. Replace the light cover by first
sliding into metal hinge and then
snapping close on opposite end.
5. Reconnect power at the main fuse or
circuit breaker.
Light
bulb
Power Failure
Do not attempt to use during a power failure. Unit will not function.
If you are unable to obtain the name of an authorized service agency, or if
you continue to have service problems, contact Viking Range Corporation
at (662) 451-4133 or write to:
VIKING RANGE CORPORATION
TROUBLE SHOOTING GUIDE
PREFERRED SERVICE
111 Front Street
Problem
Possible Cause and/or Remedy
Greenwood, Mississippi (MS) 38930 USA
1. Oven will not function
Oven is not connected to electrical
power. Have electrician check power
circuit breaker, wiring and fuses.
Record the following information indicated below. You will need it if service
is ever required. The serial number and model number for your oven is
located on the identification plate mounted on the bottom left side of the
oven door opening.
2. Oven does not
Door is not shut tight enough for
automatic door latch to lock.
operate in self-clean
Model Number
Date of Purchase
Dealer's Name
Address
Serial Number
Date Installed
3. Oven is not clean
after self-clean cycle
Temperature control knob not rotated all
the way pass cletent until it stops.
4. Broil does not
work
Temperature control knob is rotated too
far past broil position.
5. Door will not open
Oven is still in self-clean mode. If oven is
hot, door latch will release when a safe
temperature is reached.
If service requires installation of parts, use only authorized parts to ensure
protection under the warranty.
6. Oven light will not work
Light bulb is burned out
Oven is not connected to power.
This manual should remain with the oven for future reference.
38
39
Download from Www.Somanuals.com. All Manuals Search And Download.
|