TL-WA601G
108M Wireless Access Point
Rev: 1.0.3
1910010121
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
FCC RF Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile
Configurations. The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Download from Www.Somanuals.com. All Manuals Search And Download.
National Restrictions
2400.0-2483.5 MHz
Country
Restriction
Reason/remark
General authorization required for outdoor use and
public service
Bulgaria
Outdoor use limited to 10 Military Radiolocation use. Refarming of the 2.4 GHz
mW e.i.r.p. within the band band has been ongoing in recent years to allow current
France
2454-2483.5 MHz
relaxed regulation. Full implementation planned 2012
If used outside of own premises, general authorization is
required
Italy
General authorization required for network and service
supply(not for spectrum)
Luxembourg
None
This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Norway
Implemented
Russian Federation
Only for indoor applications
Note: Please don’t use the product outdoors in France.
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Chapter 1 Introduction........................................................................................... 2
1.1 Product Overview .............................................................................................. 2
1.2 Main Features ................................................................................................... 2
1.3 Conventions ...................................................................................................... 3
Chapter 2 Hardware Installation............................................................................ 3
2.1 The Front Panel................................................................................................. 3
2.1.1 LED Explanation.................................................................................................3
2.2 The Back Panel................................................................................................. 4
2.3 System Requirements ....................................................................................... 4
2.4 Installation Environment Requirements............................................................. 4
2.5 Connecting the Device ...................................................................................... 5
2.6 Configure PC..................................................................................................... 5
Chapter 3 Software Configuration ........................................................................ 9
3.1 Login.................................................................................................................. 9
3.2 Status .............................................................................................................. 10
3.3 Network ........................................................................................................... 11
3.4 Wireless........................................................................................................... 11
3.4.1 Basic Settings...................................................................................................12
3.4.2 Wireless Mode..................................................................................................13
3.4.3 Site Survey .......................................................................................................18
3.4.4 Security Settings...............................................................................................19
3.4.5 MAC Filtering....................................................................................................21
3.4.6 Wireless Statistics.............................................................................................24
3.5 DHCP .............................................................................................................. 24
3.5.1 DHCP Settings..................................................................................................25
3.5.2 DHCP Clients List.............................................................................................26
3.5.3 Address Reservation ........................................................................................26
3.6 Wireless Settings............................................................................................. 27
3.7 System Tools................................................................................................... 28
3.7.1 Firmware...........................................................................................................28
3.7.2 Factory Defaults................................................................................................29
3.7.3 Backup & Restore.............................................................................................30
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7.4 Reboot ..............................................................................................................30
3.7.5 Password..........................................................................................................31
3.7.6 Syslog...............................................................................................................31
Appendix A: Glossary......................................................................................... 33
Appendix B: Specifications................................................................................ 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Package Contents
The following items should be found in your package:
¾
¾
¾
One TL-WA601G 108Mbps Wireless Access Point
One AC power Adapter for TL-WA601G 108Mbps Wireless Access Point
One Resource CD , including:
z
z
This User Guide
Other Helpful Information
Note:
)
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Chapter 1 Introduction
Thank you for choosing the TL-WA601G 108Mbps Wireless Access Point.
1.1 Product Overview
This AP provides smooth connectivity between Ethernet wired networks and radio-equipped
wireless devices.
It adopts 108M Super G™ WLAN Transmission Technology, which offers the highest throughput
performance available on the market today, and data rates of up to 108Mbps. In dynamic 108M
mode, the AP can attach IEEE 802.11b, 802.11g and 108Mbps Super G™ devices at the same
time in an integrated environment.
It adopts 2x to 3x eXtended Range™ WLAN transmission technology so that transmission
distance is 2-3 times of traditional IEEE 802.11g and IEEE 802.11b solutions, up to 855.36m
tested in China. The transmission range is extended to 4-9 times.
It is an easy, web-based setup for installation and management. Even though you may not be
familiar with the AP, this guide will make configuring the AP easy. Before installing the AP, please
look through this guide to get to know all the AP’s functions.
1.2 Main Features
¾
¾
Complies with IEEE802.11g, IEEE802.11b, IEEE802.3, IEEE802.3u standards
Adopts 2x to 3x eXtended Range™ and 108M Super G™ wireless LAN transmission
technology.
¾
Supports 108/54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps wireless LAN data transfer
rates
¾
¾
Provides 64/128/152-bit WEP encryption security
Provides WPA/WPA2 and WPA-PSK/WPA2-PSK authentication and TKIP/AES encryption
security
¾
¾
¾
Built-in DHCP server supporting dynamic IP address distributing
Supports MAC address filtering
Supports multiple operating modes (Access Point, Client, Repeater, Point to Point, Point to
Multi-point)
¾
¾
¾
¾
Supports TCP/IP, DHCP
Supports Traffic statistics
Supports firmware upgrade
Supports Remote and Web management
2
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
1.3 Conventions
The AP or TL-WA601G, or device mentioned in this User guide stands for TL-WA601G 108M
Wireless Access Point without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may differ
from the actual situation.
You can set the parameters according to your demand.
Chapter 2 Hardware Installation
2.1 The Front Panel
Figure 2-1
The LED indicators displayed on the front panel, the status of these LED indicators represent the
device’s working circs. For details, please refer to 2.1.1 LED Explanation
2.1.1 LED Explanation
Name
Status
Off
Description
No Power
Power on
Power
On
Off
The AP has a hardware error
The AP is initialising
System
On
Flashing The AP is working properly
Off
On
There is no device linked to the corresponding port
There is a device linked to the corresponding port but no activity
LAN
Flashing There is an active device linked to the corresponding port
Off The Wireless Radio function is disabled
WLAN
Flashing The Wireless Radio function is enabled
3
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
2.2 The Back Panel
Figure 2-2
¾
¾
¾
Wireless antenna
Factory Default Reset button
There are three ways to reset the AP's factory defaults:
•
•
•
Use the Factory Defaults function on System Tools -> Factory Defaults page in the
AP's Web-based Utility.
Use the Factory Default Reset button: Press and hold the default Reset button for 5
seconds, and then the AP reboot after the System led flash 5 times.
Use the Factory Default Reset button: First, turn off the AP's power. Second, press and
hold the default Reset button then turn on the AP's power, until the system LED lights up
(about 3 seconds). Last, release the reset button and wait for the AP to reboot.
Note:
)
Ensure the AP is powered on before it restarts completely.
¾
¾
One LAN 10/100Mbps RJ45 port for connecting the AP to hub or switch
AC power socket: Only use the power adapter provided with the TL-WA601G 108Mbps
Wireless Access Point; Usage of a different adapter may result in product damage.
2.3 System Requirements
¾
¾
¾
¾
¾
¾
Broadband Internet Access Service (DSL/Cable/Ethernet)
One DSL/Cable Modem that has an RJ45 connector
A Ethernet broadband router
TCP/IP protocol must be installed on each PC
Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later
802.11g or 802.11b-compliant devices, such as the TL-WN510G Wireless Adapter
2.4 Installation Environment Requirements
¾
Not in direct sunlight or near a heater or heating vent
4
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
¾
Not cluttered or crowded. There should be at least 2 inches (5 cm) of clear space on all sides
of the AP
¾
Well ventilated (especially if it is in a closet)
¾
Operating temperature: 0℃~40℃ (32℉~104℉)
Operating Humidity: 10%~90%RH, Non-condensing
¾
2.5 Connecting the Device
Figure 2-3 is an example of an infrastructure network incorporating the TL-WA601G. An
Infrastructure network contains an access point or a wireless router. For a typical connection of the
AP, please do the following:
1. You will need broadband Internet access (a Cable or DSL-subscriber line into your home or
office). Consult with your Cable or DSL provider for proper installation of the modem.
2. Connect the Cable or DSL modem to a Router. Quickly install the router.
3. Locate an optimum location for the AP. The best place is usually near the center of the area in
which your PC(s) will wirelessly connect. The place must accord with the Installation
4. Adjust the direction of the antenna. Normally, upright is a good direction.
5. Connect the Ethernet Broadband Router to the TL-WA601G AP. Power on the AP.
6. If you are connecting a desktop PC or laptop to your network, install the TP-LINK Wireless
Adapter on the PC.
Figure 2-3 The Example of Infrastructure Network Incorporating the TL-WA601G
2.6 Configure PC
After connecting the TL-WA601G AP into your network, you should configure it. The default IP
address of the TL-WA601G 108Mbps Wireless Access Point is 192.168.1.1, and the default
5
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Subnet Mask is 255.255.255.0. These values can be seen from the LAN. They can be changed as
you desire, as an example we use the default values for description in this guide.
Connect the local PCs to the LAN ports on the AP and configure the IP address manually for your
PCs.
1. From the Start menu on your desktop, go to Settings, and then click on Network
Connections.
Figure 2-4
2. In the Network Connections window, right-click on LAN (Local Area Connection), then click
Properties.
Figure 2-5
3. In the General tab of Internet Protocol (TCP/IP) Properties menu, highlight Internet
Protocol (TCP/IP) under “This connection uses the following items:” by clicking on it once.
Click on the Properties button.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Figure 2-6
4. Configure the IP address manually. Click OK.
Figure 2-7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
1) Open TCP/IP Properties of the LAN card in your PC, enter the IP address as 192.168.1.*
(* is any value between 2 to 254, Subnet mask is 255.255.255.0, Gateway is 192.168.1.1,
DNS address is the value provided by ISP).
2) Now, you can run the Ping command in the command prompt to verify the network
connection between your PC and the AP. The following example is in Windows XP
Operating System.
3) Open a command prompt, From the Start menu on your desktop, select run tab, type
cmd in the field, and type ping 192.168.1.1 on the screen that appears, and then press
Enter.
If the result displayed is similar to that shown in Figure below, the connection between your PC
and the AP has been established.
Figure 2-8
If the result displayed is similar to that shown in Figure below, it means that your PC has not
connected to the AP.
Figure 2-9
Please check it following these steps:
Note:
)
If the connection between your PC and the AP is correct?
The LEDs of LAN port which you link to on the device and LEDs on your PC's adapter should be
lit.
If the TCP/IP configuration for your PC is correct?
If the AP's IP address is 192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Chapter 3 Software Configuration
This User Guide recommends using the “Quick Installation Guide” for first-time installation. For
advanced users, if you want to know more about this device and make use of its functions
adequately, you need to read this chapter and configure advanced settings through the
Web-based Utility.
3.1 Login
The TL-WA601G 108Mbps Wireless Access Point is easy to configure and manage With a
Web-based (Internet Explorer or Netscape® Navigator) utility. The Web-based utility can be used
on any Windows, Macintosh or UNIX OS with a web browser.
Figure 3-1 Login to the AP
User Name and Password, both in lower case letters. Then click the OK button or press the Enter key.
Figure 3-2 Login Windows
Note:
)
If the above screen does not prompt, it means that your web-browser has been set to a proxy. Go
to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel
the Using Proxy checkbox, and click OK to finish it.
After your successful login, you can configure and manage the AP. There are six main menus on
the left of the web-based utility. Submenus will be available after you click one of the main menus.
The six main menus are: Status, Network, Wireless, DHCP, Wireless Settings and System
Tools. On the right of the web-based utility, there are the detailed explanations and instructions for
the corresponding page. To apply any settings you have altered on the page, please click the
Save button.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
There are the detailed explanations for each web page's key functions below.
3.2 Status
The Status page displays the AP's current status and configuration. All information is read-only.
¾ Wired - This field displays the current settings or information for the Network, including the
MAC address, IP address and Subnet Mask.
¾ Wireless - This field displays basic information or status for wireless function, including
Operating Mode, SSID, Channel, Mode, MAC Address and IP Address.
¾ Traffic Statistics - This field displays the AP's traffic statistics.
¾ System Up Time - The time of the AP running from it's powered on or reset.
Figure 3-3 AP Status
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
3.3 Network
You can configure the IP parameters of Network on this page.
Figure 3-4 Network
¾
¾
¾
Type - Choosing dynamic IP to get IP address from DHCP server, or choosing static IP to
config IP address manually.
IP Address - Enter the IP address of your AP in dotted-decimal notation (factory default:
192.168.1.1).
Subnet Mask - An address code that determines the size of the network. Normally use
255.255.255.0 as the subnet mask.
¾
¾
Gateway - The gateway should be in the same subnet as your IP address.
MAC Address - the physical address of the AP, as seen from the LAN. The value can't be
changed.
Note:
)
If you change the IP Address, you must use the new IP Address to login the AP.
If the new LAN IP Address you set is not in the same subnet, the IP Address pool in the DHCP
sever will not take effect, until they are re-configured.
3.4 Wireless
Figure 3-5 The Wireless menu
Wireless mode, Security Settings, MAC Filtering and Wireless Statistics. Click any of them,
and you will be able to configure the corresponding function. The detailed explanations for each
submenu are provided below.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
3.4.1 Basic Settings
Figure 3-6 Wireless Settings
¾
SSID - Enter a value of up to 32 characters. The same name (SSID) must be assigned to all
wireless devices in your network. The default SSID is TP-LINK_xxxxxx (xxxxxx indicates the
last unique six characters of each device's MAC address), which can ensure your wireless
network security. But it is recommended strongly that you change your networks name (SSID)
to a different value. This value is case-sensitive. For example, TP-LINK is NOT the same as
tp-link.
¾
¾
Channel - This field determines which operating frequency will be used. It is not necessary to
change the wireless channel unless you notice interference problems with another nearby
access point.
Mode - Select the desired wireless mode. The options are:
•
108Mbps (Dynamic) - Super G™, 802.11g and 802.11b wireless stations can connect to
the AP.
•
•
•
108Mbps (Static) - Only Super G™ wireless stations can connect to the AP.
54Mbps (802.11g) - Both 802.11g and 802.11b wireless stations can connect to the AP.
11Mbps (802.11b) - Only 802.11b wireless stations can connect to the AP.
¾
Region - Select your region from the pull-down list. This field specifies the region where the
wireless function of the AP can be used. If your country or region is not listed, please contact
your local government agency for assistance.
The default region is United States. When you select your local region from the pull-down list, the
dialog shown in Figure appears below. Click OK.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Note:
)
Limited by local law regulations, version for North America does not have region selection option.
The wireless basic settings for this version are shown below.
Note:
)
To apply any settings you have altered on the page, please click the Save button, and wait the AP
reboot automatically.
3.4.2 Wireless Mode
The wireless mode settings for the wireless network are set on this page.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Figure 3-7 Wireless Mode Settings
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
¾
Disable Wireless - The wireless of this AP can be enabled or disabled to allow wireless
stations access. If disabled, wireless stations will not be able to access the AP.
Note:
)
AP provides five operational modes: Access Point, Client, Repeater, Bridge (point to point), Bridge
(point to Multi-point).
¾
Access Point - Access Point mode allows wireless stations including AP clients to access.
•
Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the
Wireless Access Point SSID will broadcast its name (SSID) on the air.
¾
Client - This mode allows one or more remote LANs connect with a central LAN, and thus
creating an extended virtual LAN. In this way, any station of the Remote LAN can successfully
communicate with any station of the central LAN, as if all of them belong to the same physical
LAN. Wireless Stations can’t associate with AP Clients.
•
Enable WDS - The AP client can connect to AP with WDS enabled or disabled. If WDS is
enabled, all traffic from wired networks will be forwarded in the format of WDS frames
consist of four address fields. If WDS is disabled, three address frames are used. If your
AP supports WDS well, please select the option.
•
•
SSID - Enter the SSID of AP that you want to access. If you select the radio before SSID,
the AP client will connect to AP according SSID.
MAC of AP - Enter the MAC address of AP that you want to access. If you select the
radio before MAC of AP, the AP client will connect to AP according MAC address.
¾
Repeater - A wireless repeater is an AP with its own BSSID that relays data to a root AP, to
which it is associated. The wireless repeater relays signal between its stations and the root
AP for greater wireless range. Please input the MAC address of root AP in the field of MAC of
AP.
¾
Universal Repeater - APs without WDS function can also be communicated with in this
mode.
Note:
)
If the available AP can’t support with WDS, you may select Client mode without WDS or Universal
Repeater mode to associate with the AP.
Here is an example of how to configure wireless repeater. Please do the following:
1. Configure the Operating Mode of the TL-WA601G Access Points.
•
•
•
Configure AP1 on LAN Segment 1 in Access Point mode.
Configure AP2 in Repeater mode with the MAC address of its root AP (AP1).
Configure AP3 in Repeater mode with the MAC address of its root AP (AP2).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Figure 3-8 Wireless repeating
2. Verify the wireless security parameters for all access points, if any.
3. Verify connectivity across the LANs. A computer on any LAN segment should be able to
connect to the Internet or share files and printers with any other PCs or servers connected to
any of the three WLAN segments.
Note:
)
You can extend this repeating by adding up to 2 additional TL-WA601Gs configured in repeater
mode. However, since Repeater configurations communicate in half-duplex mode, the bandwidth
decreases as you add Repeaters to the network. Also, you can extend the range of the wireless
network with wireless antenna accessories.
¾
Bridge (Point to Point) - This mode bridges the AP and another AP also in bridge mode to
connect two wired LANs. Please input the MAC address of the other AP in the field of MAC of
AP.
•
With AP mode: If you select this option, you AP will also support AP mode when it is in
Bridge (Point to Point) mode.
Here is an example of how to configure Point-to-Point Bridge. Please do the following:
Figure 3-9 Point to Point Bridge
1. Configure the TL-WA601G (AP1) on LAN Segment 1 in Point-to-Point Bridge mode.
2. Configure the TL-WA601G (AP2) on LAN Segment 2 in Point-to-Point Bridge mode. AP1
must have AP2’s MAC address in its MAC Address field and AP2 must have AP1’s MAC
address in its MAC Address field.
3. Configure and verify the following parameters for both access points:
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Both use the same Channel and security settings if security is in use.
•
•
Verify connectivity across the LAN 1 and LAN 2. A computer on either LAN segment
should be able to connect to the Internet or share files and printers of any other PCs or
servers connected to LAN Segment 1 or LAN Segment 2.
¾
Bridge (Point to Multi-Point) - This mode bridges the AP and up to 6 APs also in bridge
mode to connect two or more wired LANs. Please input the MAC address of other APs in the
field of MAC of AP1 to MAC of AP6.
•
With AP mode: If you select this option, you AP will also support AP mode when it is in
Bridge (Point to Multi-Point) mode.
Here is an example of how to configure multi-point bridging. Please do the following:
Figure 3-10 Point to Multi-point Bridge
1. Configure the Operating Mode of the TL-WA601G Access Points.
•
Because it is in the central location, configure TL-WA601G (AP1) on LAN Segment 1 in
Point-to-Multi-Point Bridge mode. The MAC addresses of AP2 and AP3 are required in
AP1.
•
•
Configure TL-WA601G (AP2) on LAN Segment 2 in Point-to-Point Bridge mode with the
MAC Address of AP1.
Configure the TL-WA601G (AP3) on LAN 3 in Point-to-Point Bridge mode with the MAC
Address of AP1.
2. Verify the following parameters for all access points.
•
•
All TL-WA601G Access Points use the same Channel, and security settings if any.
All Point-to-Point APs must have AP1’s MAC address in its AP MAC address field, and
AP1 must have all All Point-to-Point APs’ MAC addresses.
3. Verify connectivity across the LANs.
•
A computer on any LAN segment should be able to connect to the Internet or share files
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
and printers with any other PCs or servers connected to any of the three LAN segments.
•
Wireless stations will not be able to connect to the TL-WA601G Access Points in the
illustration above. If you require wireless stations to access any LAN segment, you can
add TL-WA601G Access Points configured in Wireless Access Point mode to any LAN
segment.
Note:
)
You can extend this multi-point bridging by adding additional TL-WA601Gs configured in
Point-to-Point mode for each additional LAN segment. Furthermore, you can extend the range of
the wireless network with wireless antenna accessories.
3.4.3 Site Survey
After selecting a mode and pressing button Survey, you can view all of APs around you.
Figure 3-11 Site Survey
¾
¾
¾
¾
¾
¾
SSID - The SSID of the AP.
BSSID - The BSSID of the AP, usually also the MAC address of the AP.
Signal - The signal received from the AP.
Channel - The channel the AP works in.
Security - The AP communicates in privacy.
Choose - Choose one AP from list to connect to.
Press one of Connect in list to select an AP to connect to. Then the basic settings will show again.
You can save settings and reboot to take effective.
Note:
)
If wireless is disabled, surveying can’t work. And if Access Point mode is selected, there is no
reason and no choice to connect to another AP, as it showed below.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
3.4.4 Security Settings
You can select one of the following security options:
Figure 3-12 Wireless Securities
Disable Security - The wireless security function can be enabled or disabled. If disabled, the
¾
wireless stations will be able to connect the AP without encryption. It is recommended
19
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
strongly that you choose one of following options to enable security.
WEP - Select 802.11 WEP security.
¾
•
Type - You can select one of following types:
1) Automatic - Select Shared Key or Open System authentication type automatically
based on the wireless station's capability and request.
2) Shared Key - Select 802.11 Shared Key authentication.
3) Open System - Select 802.11 Open System authentication.
•
•
•
WEP Key Format - You can select ASCII or Hexadecimal format. ASCII Format stands
for any combination of keyboard characters in the specified length. Hexadecimal format
stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length.
WEP Key settings - Select which of the four keys will be used and enter the matching
WEP key information for your network in the selected key radio button. These values
must be identical on all wireless stations in your network.
Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for
encryption. "Disabled" means this WEP key entry is invalid.
1) For 64-bit encryption - You can enter 10 hexadecimal digits (any combination of 0-9,
a-f, A-F, zero key is not permitted) or 5 ASCII characters.
2) For 128-bit encryption - You can enter 26 hexadecimal digits (any combination of
0-9, a-f, A-F, zero key is not permitted) or 13 ASCII characters.
3) For 152-bit encryption - You can enter 32 hexadecimal digits (any combination of
0-9, a-f, A-F, zero key is not permitted) or 16 ASCII characters.
Note:
)
If you do not set the key, the wireless security function is still disabled even if you have selected
Shared Key as Authentication Type.
¾
WPA/WPA2 - Select WPA/WPA2 based on Radius Server.
•
Version - You can select one of following versions,
1) Automatic - Select WPA or WPA2 automatically based on the wireless station's
capability and request.
2) WPA - Wi-Fi Protected Access.
3) WPA2 - WPA version 2.
•
•
•
•
Encryption - You can select either Automatic, or TKIP or AES.
Radius Server IP - Enter the IP address of the Radius Server.
Radius Port - Enter the port that radius service used.
Radius Password - Enter the password for the Radius Server.
¾
WPA-PSK/ WPA2-PSK - Select WPA based on pre-shared passphrase.
•
Version - You can select one of following versions
1) Automatic - Select WPA-PSK or WPA2-PSK automatically based on the wireless
station's capability and request.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
2) WPA-PSK - Pre-shared key of WPA.
3) WPA2-PSK - Pre-shared key of WPA2.
•
•
PSK Passphrase - You can enter a passphrase between 8 and 63 characters long.
Group Key Update Period - Specify the group key update interval in seconds. The value
can be either 0 or at least 30. Enter 0 to disable the update.
Be sure to click the Save button to save your settings on this page.
Note:
)
The AP will reboot automatically after you click the Save button.
3.4.5 MAC Filtering
Figure 3-13 Wireless MAC address Filtering
The Wireless MAC Address Filtering feature allows you to control wireless stations accessing the
AP, which depend on the station's MAC addresses.
¾
¾
¾
MAC Address - The wireless station's MAC address that you want to access.
Description - A simple description of the wireless station.
Privilege - Allow means allowing the station to access the AP. Deny means denying the
station to access the AP. 64-bit, or 128-bit, or 152-bit means assigning a unique WEP key to
access the AP.
¾
¾
WEP Key - Specify a unique WEP key (in Hexadecimal format) to access the AP.
Status - The status of this entry, either Enabled or Disabled.
To disable the Wireless MAC Address Filters feature, keep the default setting, Disable.
To set up an entry, click Enable, and follow these instructions:
Step1：First, you must decide whether the unspecified wireless stations can or cannot access the
AP. If you desire that the unspecified wireless stations can access the AP, please select
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
the radio button Allow the stations not specified by any enabled entries in the list to
access, otherwise, select the radio button Deny the stations not specified by any
enabled entries in the list to access.
Step2：To Add a Wireless MAC Address filtering entry, click the Add New… button. The “Add or
Figure 3-14 Add or Modify Wireless MAC Address Filtering entry
To add or modify a MAC Address Filtering entry, follow these instructions:
1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC
Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example:
00-0A-EB-B0-00-0B.
2. Enter a simple description of the wireless station in the Description field. For example:
Wireless station A.
3. Privilege - Selects the privileges for this entry, one of Allow / Deny / 64-bit / 128-bit /
152-bit.
4. WEP Key - If you select 64-bit, 128-bit or 152-bit in the Privilege field, enter any
combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. For example:
2F34D20BE2.
5. Status - Select Enabled or Disabled for this entry on the Status pull-down list.
6. Click the Save button to save this entry.
To add additional entries, repeat steps 1-6.
Note:
)
When 64-bit, or 128-bit, or 152-bit is selected, WEP Key will be enabled.
To modify or delete an existing entry:
1. Click the Edit or Delete button in the Modify column in the MAC Address Filtering Table.
2. Enter the value as desired in the Add or Modify Wireless MAC Address Filtering entry
page, and click the Save button.
You can click the Enable All button to make all the entries effective, click the Disable All button to
make all the entries ineffective, click the Delete All button to delete all the entries.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Click the Next button to go to the next page and click the Previous button to return to the previous
page.
For example:
If you desire that the wireless station A with MAC address 00-0A-EB-00- 07-BE be able to access
the AP, the wireless station B with MAC address 00-0A-EB- 00-07-5F not be able to access the AP,
and the wireless station C with MAC address 00-0A-EB-00-07-8A be able to access the AP when its
WEP key is 2F34D20BE2E54B326C5476586A, while all other wireless stations cannot access the
AP, you should configure the Wireless MAC Address Filtering list following these steps:
1. Click the Enable button to enable this function.
2. Select the radio button: Deny the stations not specified by any enabled entries in the list
to access for Filtering Rules.
3. Delete all or disable all entries if there are any entries existing already.
4. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-BE in the MAC
Address field, enter wireless station A in the Description field, select Allow in the Privilege
pull-down list and select Enabled in the Status pull-down list. Click the Save and the Back
button.
5. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-5F in the MAC
Address field, enter wireless station B in the Description field, select Deny in the Privilege
pull-down list and select Enabled in the Status pull-down list. Click the Save and the Back
button.
6. Click the Add New... button and enter the MAC address 00-0A-EB-00-07-8A in the MAC
Address field, enter wireless station C in the Description field, select 128-bit in the Privilege
pull-down list, enter 2F34D20BE2E54B326C5476586A in the WEP Key field and select
Enabled in the Status pull-down list. Click the Save and the Back button.
The filtering rules that configured should be similar to the following list:
23
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Note:
)
If you select the radio button Allow the stations not specified by any enabled entries in the list
to access for Filtering Rules, the wireless station B will still not be able to access the AP,
however, other wireless stations that are not in the list will be able to access the AP.
If you enable the function and select the Deny the stations not specified by any enabled
entries in the list to access for Filtering Rules, and there are not any enable entries in the list,
thus, no wireless stations can access the AP.
3.4.6 Wireless Statistics
This page shows MAC Address, Current Status, Received Packets and Sent Packets for each
connected wireless station.
Figure 3-15 The AP attached wireless stations
¾
¾
MAC Address - The connected wireless station's MAC address
Current Status - The connected wireless station's running status, one of STA-AUTH /
STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN /
Disconnected
¾
¾
Received Packets - packets received by the station
Sent Packets - packets sent by the station
You cannot change any of the values on this page. To update this page and to show the current
connected wireless stations, click on the Refresh button.
If the numbers of connected wireless stations go beyond one page, click the Next button to go to
the next page and click the Previous button to return the previous page.
Note:
)
This page will be refreshed automatically every 5 seconds.
3.5 DHCP
Figure 3-16 The DHCP menu
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Clients List and Address Reservation. Click any of them, and you will be able to configure the
corresponding function. The detailed explanations for each submenu are provided below.
3.5.1 DHCP Settings
The System can be set up as a DHCP (Dynamic Host Configuration Protocol) server, which
provides the TCP/IP configuration for all the PCs that are connected to the system on the LAN.
Figure 3-17 DHCP Settings
¾
¾
¾
¾
DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have
another DHCP server within your network or else you must manually configure the computer.
Start IP Address - This field specifies the first of the addresses in the IP address pool.
192.168.1.100 is the default start address.
End IP Address - This field specifies the last of the addresses in the IP address pool.
192.168.1.199 is the default end address.
Address Lease Time - The Address Lease Time is the amount of time a network user will
be allowed connection to the system with their current dynamic IP Address. Enter the amount
of time, in minutes, the user will be "leased" this dynamic IP Address. The range of the time is
1 ~ 2880 minutes. The default value is 120 minutes.
¾
¾
¾
Default Gateway - (Optional.) Input the IP Address of the gateway.
Default Domain - (Optional.) Input the domain name of your network.
Primary DNS - (Optional.) Input the DNS IP address provided by your ISP. Or consult your
ISP.
¾
Secondary DNS - (Optional.) Input the IP address of another DNS server if your ISP provides
two DNS servers.
Note:
)
To use the DHCP server function of the AP, you must configure all computers on the LAN as
"Obtain an IP Address automatically" mode. This function will take effect until the AP reboots.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
3.5.2 DHCP Clients List
This page shows Client Name, MAC Address, Assigned IP and Lease Time for each DHCP
Figure 3-18 DHCP Clients List
¾
¾
¾
¾
¾
Index - The index of the DHCP Client
Client Name - The name of the DHCP client
MAC Address - The MAC address of the DHCP client
Assigned IP - The IP address that the AP has allocated to the DHCP client.
Lease Time - The time of the DHCP client leased. Before the time is up, DHCP client will
request to renew the lease automatically.
You cannot change any of the values on this page. To update this page and to show the current
attached devices, click on the Refresh button.
3.5.3 Address Reservation
When you specify a reserved IP address for a PC on the LAN, that PC will always receive the
same IP address each time when it accesses the DHCP server. Reserved IP addresses should be
assigned to servers that require permanent IP settings. This page is used for address reservation
Figure 3-19 Address Reservation
¾
MAC Address - The MAC address of the PC of which you want to reserve IP address.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
¾
Assigned IP Address - The IP address of the AP reserved.
To Reserve IP addresses:
1. Click the Add New... button to add a new Address Reservation entry.
2. Enter the MAC address (The format for the MAC Address is XX-XX-XX-XX-XX-XX.) and IP
address in dotted-decimal notation of the computer you wish to add.
3. Click the Save button when finished.
To modify A Reserved IP address:
1. Select the reserved address entry as you desire, and modify it. If you wish to delete the entry,
make all of the entry fields blank.
2. Click the Save button.
To delete all Reserved IP addresses:
Click the Clear All button.
Click the Save button.
Click the Next button to go to the next page and Click the Previous button to return the previous
page.
Note:
)
The function won't take effect until the AP reboots.
3.6 Wireless Settings
You can configure wireless advanced settings on this page.
Figure 3-20 AP Wireless Advanced Settings
¾
¾
Enable AP Isolation - Isolate all connected wireless stations so that wireless stations can not
access each other through WLAN. This option is available only for AP mode.
Disable short preamble - Disable short preamble and use long preamble only. 802.11b
mode supports only long preamble and this parameter will be ignored.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
¾
RTS threshold - RTS/CTS Threshold, the packet size that is used to determine if RTS/CTS
should be sent.
¾
¾
¾
Fragmentation threshold - The maximum packet size used for fragmentation.
Beacon Interval - The interval time between two successive beacons.
Power - The transmit power of the access point.
Note:
)
Limited by local law regulations, version for North America does not have power selection option.
The wireless advanced settings for this version are shown below.
Note:
)
The AP will reboot automatically after you click the Save button.
3.7 System Tools
Figure 3-21 The System Tools menu
Factory Defaults, Reboot, Password, and Syslog. Click any of them, and you will be able to
configure the corresponding function. The detailed explanations for each submenu are provided
below.
3.7.1 Firmware
28
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Figure 3-22 Firmware Upgrade
not experiencing difficulties, there is no need to download a more recent firmware version, unless
that version has a new feature that you want to use.
Note:
)
When you upgrade the AP's firmware, you may lose its configuration settings, so make sure you
write down the AP settings before you upgrade its firmware.
To upgrade the AP's firmware, follow these instructions:
2. Click Browse to view the folders and select the downloaded file.
3. Click the Upgrade button.
¾
¾
Firmware Version - displays the current firmware version.
Hardware Version - displays the current hardware version. The hardware version of the
upgrade file must accord with the current hardware version.
Note:
)
Do not turn off the AP or press the Reset button while the firmware is being upgraded.
The AP will reboot after the Upgrading has been finished.
3.7.2 Factory Defaults
Figure 3-23 Restore Factory Default
Click the Restore button to reset all configuration settings to their default values.
•
The default User Name: admin
29
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
The default Password: admin
•
•
•
The default IP Address: 192.168.1.1
The default Subnet Mask: 255.255.255.0
Note:
)
Any settings you have saved will be lost when the default settings are restored.
3.7.3 Backup & Restore
computer as a file or restore the AP's configuration.
Figure 3-24 Save or Restore the Configuration
Click the Backup button to save all configuration settings to your local computer as a file.
To restore the AP's configuration, follow these instructions:
•
•
Click the Browse button to find the configuration file which you want to restore.
Click the Restore button to update the configuration with the file whose path is the one
you have input or selected in the blank.
Note:
)
The current configuration will be covered with the uploading configuration file. Wrong process will
lead the device unmanaged. The restoring process lasts for 20 seconds and restart automatically
then. Keep the power of the device on during the process, in case of any damage.
3.7.4 Reboot
Figure 3-25 Reboot the AP
Click the Reboot button to reboot the AP.
Some settings of the AP will take effect only after rebooting, which include:
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Change LAN IP Address. (System will reboot automatically)
•
•
•
•
•
DHCP service function.
Static address assignment of DHCP server.
Upgrade the firmware of the AP (system will reboot automatically).
Restore the AP's settings to factory default (system will reboot automatically).
3.7.5 Password
password of the AP.
Figure 3-26 Password
It is strongly recommended that you change the factory default user name and password of the AP.
All users who try to access the AP's web-based utility or Quick Setup will be prompted for the AP's
user name and password.
Note:
)
The new user name and password must not exceed 14 characters in length and must not include
any spaces. Enter the new Password twice to confirm it.
Click the Save button when finished.
Click the Clear All button to clear all.
3.7.6 Syslog
31
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Figure 3-27 System Log
The AP can keep logs of all traffic. You can query the logs to find what happened to the AP.
Click the Refresh button to refresh the logs.
Click the Clear ALL button to clear all the logs.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Appendix A: Glossary
108M Super G™ WLAN Transmission Technology - 108M Super G™ WLAN Transmission
Technology employs multiple performance-enhancing techniques including packet bursting, fast
frames, data compression, and dynamic turbo mode that combine to improve the throughput and
range of wireless networking products. Users can experience link rates of up to 108Mbps, twice
the industry-standard maximum data link rate of 54Mbps, while preserving full compatibility with
traditional 802.11g or 802.11b networks. 108M Super G™ products offer the highest throughput
performance available on the market today. In dynamic 108M mode, the device can attach
802.11b, 802.11g and 108Mbps Super G™ devices at the same time in an integrated environment.
2x to 3x eXtended RangeTM WLAN Transmission Technology - The WLAN device with 2x to 3x
eXtended RangeTM WLAN transmission technology make its sensitivity up to 105 dBm, which
gives users the ability to have robust, longer-range wireless connections. With this
range-enhancing technology, a 2x to 3x eXtended RangeTM based client and access point can
maintain a connection at as much as three times the transmission distance of traditional 802.11b
and 802.11g products, for a coverage area that is up to nine times greater. A traditional 802.11b
and 802.11g product transmission distance is about 300m. A 2x to 3x eXtended RangeTM based
client and access point can maintain a connection transmission distance may be up to 830m.
802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using
direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio
spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as
Wi-Fi networks.
802.11g
-
specification for wireless networking at 54 Mbps using direct-sequence
spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed
radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP
encryption for security.
Access Point (AP) - A wireless LAN transceiver or "base station" that can connect a wired LAN to
one or many wireless devices. Access points can also bridge to each other.
DNS (Domain Name System) – An Internet Service that translates the names of websites into IP
addresses.
Domain Name - A descriptive name for an address or group of addresses on the Internet.
DoS (Denial of Service) - A hacker attack designed to prevent your computer or network from
operating or communicating.
DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over existing
traditional phone lines.
ISP (Internet Service Provider) - A company that provides access to the Internet.
MTU (Maximum Transmission Unit) - The size in bytes of the largest packet that can be
transmitted.
SSID - A Service Set Identification is a thirty-two character (maximum) alphanumeric key
identifying a wireless local area network. For the wireless devices in a network to communicate
with each other, all devices must be configured with the same SSID. This is typically the
configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless
Access Point and to the wireless network name.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or
152-bit shared key algorithm, as described in the IEEE 802.11 standard.
Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless
promoting interoperability among 802.11b devices.
WLAN (Wireless Local Area Network) - A group of computers and associated devices
communicate with each other wirelessly, which network serving users are limited in a local area.
WPA (Wi-Fi Protected Access) - WPA is a security technology for wireless networks that improves
on the authentication and encryption features of WEP (Wired Equivalent Privacy). In fact, WPA
was developed by the networking industry in response to the shortcomings of WEP. One of the
key technologies behind WPA is the Temporal Key Integrity Protocol (TKIP). TKIP addresses the
encryption weaknesses of WEP. Another key component of WPA is built-in authentication that
WEP does not offer. With this feature, WPA provides roughly comparable security to VPN
tunneling with WEP, with the benefit of easier administration and use. This is similar to 802.1x
support and requires a RADIUS server in order to implement. The Wi-Fi Alliance will call this,
WPA-Enterprise. One variation of WPA is called WPA Pre Shared Key or WPA-PSK for short - this
provides an authentication alternative to an expensive RADIUS server. WPA-PSK is a simplified
but still powerful form of WPA most suitable for home Wi-Fi networking. To use WPA-PSK, a
person sets a static key or "passphrase" as with WEP. But, using TKIP, WPA-PSK automatically
changes the keys at a preset time interval, making it much more difficult for hackers to find and
exploit them. The Wi-Fi Alliance will call this, WPA-Personal.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Appendix B: Specifications
General
IEEE 802.3, 802.3u, 802.11b and 802.11g, TCP/IP, DHCP
FCC、CE
Standards and Protocols
Safety & Emission
One 10/100M Auto-Negotiation LAN RJ45 port supporting Auto
MDI/MDIX
Ports
10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
Cabling Type
LEDs
100BASE-TX: UTP category 5, 5e cable (maximum 100m)
EIA/TIA-568 100Ω STP (maximum 100m)
POWER, SYSTEM, LAN, WLAN
Wireless
108/54/48/36/24/18/12/9/6Mbps or 11/5.5/3/2/1Mbps
64/128/152 bits
Wireless Data Rates
WEP
Wireless Certification
Wi-Fi WPA
Physical and Environment
0℃~40℃ (32℉~104℉)
Working Temperature
Working Humidity
10% ~ 90% RH, Non-condensing
-40℃~70℃(-40℉~158℉)
Storage Temperature
Storage Humidity
5% ~ 90% RH, Non-condensing
35
Download from Www.Somanuals.com. All Manuals Search And Download.
TL-WA601G 108M Wireless Access Point User Guide
Appendix C: FAQ
1. No lights are lit on the access point.
It takes a few seconds for the power indicator to light up. Wait a minute and check the power light
status on the access point if the access point has no power.
1) Make sure the power cord is connected to the access point.
2) Make sure the power adapter is connected to a functioning power outlet. If it is in a power
strip, make sure the power strip is turned on. If it is plugged directly into the wall, verify
that it is not a switched outlet.
3) Make sure you are using the correct TP-LINK power adapter supplied with your access
point.
2. The LAN light is not lit.
There is a hardware connection problem. Check these items:
1) Make sure the cable connectors are securely plugged in at the access point and the
network device (hub, switch, or router).
2) Make sure the connected device is turned on.
3) Be sure the correct cable is used. Use a standard Category 5 Ethernet patch cable. If the
network device has Auto Uplink™ (MDI/MDIX) ports, you can use either a crossover
cable or a normal patch cable.
3. I cannot access the AP with a wireless capable computer.
There is a configuration problem. Check these items:
1) You may not have restarted the computer with the wireless adapter to have TCP/IP
changes take effect. Restart the computer.
2) The computer with the wireless adapter may not have the correct TCP/IP settings to
communicate with the network. Restart the computer and check that TCP/IP is set up
properly for that network. The usual setting for Windows the Network Properties is set to
“Obtain an IP address automatically.”
3) The access point’s default values may not work with your network. Check the access
point default configuration against the configuration of other devices in your network.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
|