BD HI FI COMPONENT SYSTEM
MODEL
XL-BD601PH
OPERATION MANUAL
iPad, iPhone, iPod, iPod classic, iPod nano and
iPod touch are trademarks of Apple Inc., registered
in the U.S. and other countries.
Download from Www.Somanuals.com. All Manuals Search And Download.
Virtajohdon asianmukainen käyttö
●
Lorsque la touche ON/STAND-BY est mise en STAND-BY, l’appareil est
toujours sous tension.
Lorsque la touche ON/STAND-BY se trouve sur la position STAND-BY,
l’appareil est prêt à fonctionner par la minuterie ou la télécommande.
Avertissement:
Cet appareil contient des pièces non réparables par l’utilisateur. Personne
non qualifiée n’enlèvera jamais les couvercles. L’appareil contenant
des organes portés à haute tension, débrancher l’appareil avant toute
réparation ou en période de non-utilisation.
●
Quando o botăo ON/STAND-BY estiver ajustado na posiçăo STAND-BY, a
voltagem de alimentaçăo ainda se encontra presente dentro do aparelho.
Quando o botăo ON/STAND-BY estiver ajustado na posiçăo STAND-BY, o
aparelho pode ser colocado em operaçăo através do modo de programaçăo
horária ou pelo controle remoto.
Noudata seuraavia ohjeita soittimen toimintahäiriöiden sekä
sähköiskun, tulipalon tai henkilövahinkojen välttämiseksi.
● Pidä pistokkeesta tukevasti kiinni, kun irrotat tai liität
virtajohdon.
● Älä säilytä tai käytä virtajohtoa lämmityslaitteiden läheisyydessä.
● Älä sijoita raskaita esineitä virtajohdon päälle.
● Älä yritä korjata tai muuttaa virtajohtoa itse millään tavalla.
Advertência:
Neste aparelho năo há partes que podem ser consertadas pelo usuário.
Nunca retire a tampa, a menos que você tenha qualificaçăo para tal.
Este aparelho contém voltagens perigosas. Remova sempre o cabo de
alimentaçăo da tomada antes de efetuar qualquer conserto ou quando
deixar o aparelho muito tempo fora de uso.
●
Cuando el botón ON/STAND-BY está puesto en la posición STAND-BY,
todavía hay tensión dentro del aparato.
Zabezpieczenie kabla zasilającego
●
Kun ON/STAND-BY -kytkin on STAND-BY-asennossa, laitteessa on yhä
virta.
Kun ON/STAND-BY -kytkin on STAND-BY-asennossa, laite voidaan kytkeä
päälle kaukosäätimestä.
Varoitus:
Laitteen sisällä ei ole käyttäjän huollettavissa olevia osia. Kotelon saa
irrottaa vain siihen pätevöitynyt henkilö. Laitteen sisällä on vaarallinen
jännite. Laite on aina irrotettava verkkovirrasta ennen huoltotoimenpiteitä
ja jos laite on pitkään käyttämättä.
Cuando el botón ON/STAND-BY está puesto en la posición STAND-
BY, el aparato puede ponerse en funcionamiento utilizando el modo del
temporizador o el controlador remoto.
Żeby zapewnić prawidłowe działanie odtwarzacza i zapobiec
porażeniu prądem, wybuchowi pożaru lub zranieniu, prosimy o
przestrzeganie poniższych wytycznych.
Advertencia:
Tenga en cuenta que dentro de este aparato no hay piezas que pueda
reparar. No quite nunca las tapas a menos que se esté cualificado para
hacerlo. Este aparato tiene en su interior tensiones peligrosas. Desenchufe
siempre la clavija de la red del tomacorriente antes de realizar cusalquier
servicio de mantenimiento y cuando no se use el aparato durante un largo
período de tiempo.
● Należy mocno trzymać wtyczkę w trakcie podłączania lub
odłączania przewodu zasilającego.
● Kabel zasilający powinien znajdować się z daleka od urządzeń
grzewczych.
● Nie wolno ustawiać ciężkich przedmiotów na kablu zasilającym.
● Nie należy próbować w żaden sposób naprawiać lub sztukować
kabla zasilającego.
●
Gdy urządzenie znajduje się w trybie czuwania, jego wewnętrzne elementy
są pod napięciem.
Gdy urządzenie znajduje się w trybie czuwania, może zostać włączone
przy pomocy zegara lub pilota.
Ostrzeżenie:
Wewnątrz urządzenia nie ma żadnych elementów wymagających
obsługi użytkownika. Obudowa może być zdejmowana wyłącznie
przez wykwalifikowanych pracowników serwisu. Wewnętrzne elementy
urządzenia znajdują się pod napięciem. Przed zdjęciem odbudowy, lub
gdy urządzenie ma zostać przez dłuższy czas nieużywane, należy wyjąć
wtyczkę z gniazdka elektrycznego.
●
När ON/STAND-BY knappen är i läge STAND-BY, finns nätspänning i
apparaten.
Med ON/STAND-BY knappen i läge STAND-BY kan apparaten startas
med timerfunktion eller fjärrkontrollen.
Varning:
Apparaten innehĺller inga delar som kan ĺtgärdas av kunden.
Höljet fĺr endast öppnas av kvalificerad personal. Apparaten innehĺller
farliga spänningar. Stickkontakten ska därför dras ut frĺn nätuttaget före
reparationsarbeten och bör dras ut om apparaten inte ska användas pĺ
mycket länge.
AC Power Lead Protection
To avoid any malfunctions of the unit, and to protect against electric
shock, fire or personal injury, please observe the following.
● Hold the plug firmly when connecting or disconnecting the AC
power lead.
● Keep the AC power lead away from heating appliances.
● Never put any heavy object on the AC power lead.
● Do not attempt to repair or reconstruct the AC power lead in any
way.
●
When the ON/STAND-BY button is set at STAND-BY position, mains
voltage is still present inside the unit.
When the ON/STAND-BY button is set at STAND-BY position, the unit may
be brought into operation by the timer mode or remote control.
Warning:
This unit contains no user serviceable parts. Never remove covers unless
qualified to do so. This unit contains dangerous voltages, always remove
mains plug from the socket before any service operation and when not in
use for a long period.
●
Quando il tasto ON/STAND-BY si trova in posizione STAND-BY, all’interno
dell’apparecchio c’è ancora la corrente.
Se il tasto ON/STAND-BY si trova nella posizione STAND-BY, l’unità puň essere
accesa con il modo timer o con il telecomando.
Avvertenza:
L’apparecchio non contiene parti riparabili dall’utente. Non togliere
mai i coperchi, a meno di non essere qualificati per farlo. All’interno
dell’apparecchio ci sono tensioni pericolose, per cui si deve sempre
staccare la spina del cavo d’alimentazione dalla presa di corrente prima
di qualsiasi intervento di manutenzione e quando non si usa l’apparecchio
per un lungo periodo di tempo.
●
Dichiarazione di conformità
La società SHARP ELECTRONICS EUROPE GmbH dichiara
che il prodotto XL-BD601PH Sistema Hi Fi Blu-ray è costruito in
conformitàalleprescrizionidelD.M.no548del28/8/95, pubblicato
sulla G.U.no 301 del 28/12/95 ed in particolare è conforme a
quanto indicato nell’art. 2, comma 1 dello stesso decreto.
●
Når ON/STAND-BY-knappen er sat i STAND-BY positionen, er der stadig
netspaending til stede i apparatet.
Når ON/STAND-BY-knappen er sat i STAND-BY position, kan apparatet
startes v.hj.a. timer-funksionen eller fjernbetjeningen.
Advarsel:
Apparatet indeholder ingen dele, der kan repareres af brugeren selv. Fjern
aldrig kabinettet med mindre De er kvalificeret hertil. Apparatet indeholder
farlig strømspaending. Traek altid stikket ud af stikkontakten før der
foretages reparationer, eller hvis apparatet ikke er i brug i laengere tid.
●
Wanneer de ON/STAND-BY toets in de STAND-BY stand staat, loopt er
nog steeds stroom (netspanning) in het toestel.
Wanneer de ON/STAND-BY toets in de STAND-BY stand staat, kan het
toestel ingeschakeld worden via de timerfunctie of de afstandsbediening.
Waarschuwing:
Dit toestel bevat geen door de gebruiker te repareren onderdelen.Verwijder
de behuizing nooit tenzij u deskundig bent op dit gebied. In het toestel
loopt een gevaarlijke spanning; haal de stekker altijd uit het stopcontact
alvorens onderhoud uit te voeren of wanneer het toestel voor langere tijd
niet gebruikt wordt.
●
Bei Einstellung der ON/STAND-BY-Taste auf STAND-BY ist die
Netzspannung immer noch im Gerät vorhanden.
Wenn die ON/STAND-BY-Taste auf STAND-BY eingestellt wird, kann das
Gerät unter Verwendung der Timer-Betriebsart oder Fernbedienung in
Betrieb gesetzt werden.
Warnung:
In diesem Gerät sind keine vom Benutzer wartbaren Teile vorhanden.
Niemals Abdeckungen entfernen, außer wenn Sie dafür qualifiziert sind. In
diesem Gerät sind gefährliche Spannungen vorhanden.Vor Ausführung von
irgendwelchen Kundendienstarbeiten oder bei längerer Nichtverwendung
des Gerätes stets den Netzstecker aus der Netzsteckdose ziehen.
ii
Download from Www.Somanuals.com. All Manuals Search And Download.
● Vorsicht:
● Advarsel:
Das Gerät wederTropf- noch Spritzwasser aussetzen. Ansonsten
besteht die Gefahr eines Brandes oder elektrischen Schlages. Es
dürfen keine mit Flüssigkeiten gefüllten Gegenstände wie Vasen
auf dem Gerät abgestellt werden.
For ĺ unngĺ brann eller kortslutning, utsett ikke produktet for vann
eller fuktighet. Gjenstander som inneholder vaeske, feks. en
blomstervase, mĺ ikke plasseres oppĺ apparatet.
DENNA APPARAT ÄR ANSLUTEN TILL 230 V VÄXELSTRÖM
NÄR STICKPROPPEN ÄR INSKJUTEN I VÄGGUTTAGET. FÖR
ATT FULLSTÄNDIGT KOPPLA IFRÅN APPARATEN, V.G. DRAG
UT STICKPROPPEN.
● Varoitus:
● Attention:
Älä vie laitetta sateeseen tai kosteisiin tiloihin. Jos laite on
kostunut, anna sen kuivua ennen kuin käytät sitä verkkovirralla.
Nestettä sisältäviä astioita kuten esim. kukkamaljakoita ei saa
asettaa laitteen päälle.
Pour éviter un incendie ou une secousse électrique, mettre
l’appareil à l’abri de l’eau (éclaboussure, goutte). Ne pas poser
sur l’appareil un récipient contenant du liquide.
● Advertencia:
● Audio-visuelles Material kann Urheberrechte umfassen, die
ohne Genehmigung des Eigentümers dieser Urheberrechte
nicht aufgenommen werden dürfen. Siehe die entsprechenden
nationalen Gesetze.
Para evitar incendios y descargas eléctricas, no exponga el
aparato a goteo o salpicadura de líquidos. No deberán ponerse
encima del aparato objetos que estén llenos de líquido, como por
ejemplo un florero.
● Le matériel audio-visuel peut comporter des oeuvres faisant
l’objet de droits d’auteur qui ne peuvent être enregistrées sans
l’autorisation du possesseur du droit d’auteur, veuillez vous
référer aux réglementations nationales en vigueur.
● Varning:
Utsätt inte enheten för dropp eller stänk för att förhindra brand
eller elektriska stötar. Inga vätskefyllda föremĺl sĺsom vaser fĺr
placeras pĺ enheten.
● Dieses Produkt ist ein Laserprodukt der Klasse 1.
● Ce produit est classifié comme étant un LASER DE CLASSE 1.
● Este producto está clasificado como un PRODUCTO LÁSER DE
● El material audiovisual puede consistir en trabajos que tengan
derechos de autor y que no deben grabarse sin la autorización
del poseedor de dichos derechos de autor. Sírvase consultar las
leyes aplicables en su país.
● Attenzione:
CLASE 1.
Per prevenire incendi o scosse elettriche, non fare gocciolare
nessun liquido sull’apparecchio e non bagnarlo. Non collocarvi
sopra nessun oggetto riempito d’acqua, come per esempio vasi.
● Denna produkt klassificeras som KLASS 1 LASERPRODUKT.
● Questo prodotto è classificato come CLASS 1 LASER PRODUCT.
● Audiovisuellt material kan innehĺlla upphovsrättsarbete som inte
skall mĺngfaldigas utan tillstĺnd av copyrightinnehavaren. Se den
tillämpliga lagen i ditt land.
● Waarschuwing:
● Dit product is geclassificeerd als een KLASSE
1
LASER
Stel het toestel niet bloot aan druipend of spattend water om
brand en elektrische schokken te voorkomen. Met vloeistoffen
gevulde voorwerpen, zoals vazen, mogen niet op het toestel
geplaatst worden.
PRODUCT.
●
Este produto é classificado como PRODUTO LASER DE CLASSE 1.
● Il materiale audio-visivo che fosse soggetto a copyright non
puň essere registrato senza l’autorizzazione del possessore del
copyright. Si prega di attenersi alle leggi in vigore sul territorio
nazionale.
● Tämä laite on luokiteltu LUOKAN 1 LASERLAITTEEKSI.
● Cuidado:
● Opisywane urządzenie jest sklasyfikowane jako PRODUKT
Para evitar incêndio ou choque elétrico, năo exponha este
aparelho a gotejamento ou salpicamento de água. Năo coloque
objetos com água como, por exemplo, um vaso de flores, em
cima do aparelho.
LASEROWY KLASY 1.
● Audio-visueel materiaal kan worden beschermd door
auteursrechten, in welk geval het niet mag worden opgenomen
zonder de toestemming van de auteursrechthouder. Zie voor
nadere informatie de betreffende wetten in het land van gebruik.
● This product is classified as a CLASS 1 LASER PRODUCT.
●
●
●
● Varoitus:
Tulipalon tai sähköiskun välttämiseksi laitetta ei saa altistaa
tippuvalle tai roiskuvalle vedelle. Nestettä sisältäviä astioita kuten
esim kukkamaljakoita ei saa asettaa laitteen päälle.
● O material audiovisual pode consistir de trabalhos de direitos
autorias que năo devem ser gravados sem autorizaçăo do
proprietário dos direitos. Favor consultar as leis vigentes em seu
país.
●
●
●
● Ostrzeżenie:
● Audiovisuaalinenmateriaalisaattaaollatekijänoikeudellasuojattua,
eikä sitä tällöin saa tallentaa ilman tekijänoikeuden haltijan lupaa.
Lisätietoja on maassasi sovellettavassa tekijänoikeuslaissa.
Żeby zapobiec niebezpieczeństwu pożaru lub porażeniu prądem,
urządzenie należy chronić przed zalaniem lub wilgocią. Na
urządzeniu nie wolno ustawiać żadnych zbiorników z wodą - np.
wazonów.
● Materiał audiowizualny może zawierać utwory chronione prawem
autorskim, które nie mogą być nagrywane bez zgody właściciela
praw autorskich. Patrz odpowiednie regulacje prawne w danym
kraju
● Warning:
To prevent fire or shock hazard, do not expose this appliance
to dripping or splashing. No objects filled with liquids, such as
vases, shall be placed on the apparatus.
● Audio-visual material may consist of copyrighted works which
must not be recorded without the authority of the owner of the
copyright. Please refer to relevant law in your country.
● Advarsel:
Til at forbygge ild og střd risiko, lad vaere med at undsaette
denne indretning for drypning eller overstaenkning. Der mĺ ikke
anbringes nogen genstande fyldt med vand, som for eksempel
vaser, pĺ dette apparat.
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
SA172WJ
CAUTION: CLASS 2 VISIBLE AND INVISIBLE LASER
● VORSICHT
● VAROITUS
RADIATION WHEN OPEN. DO NOT STARE INTO THE BEAM.
ACHTUNG: BEI GEÖFFNETER ABDECKUNG IST SICHTBARE UND
Verwendung von Regelungen oder Einstellungen bzw.
Durchführung von anderen Verfahren als die hierin angegebenen
kann zum Aussetzen gefährlicher Strahlung führen.
Da der in diesem Compact Disc Player verwendete Laserstrahl für
die Augen schädlich ist, ist das Gehäuse unter keinen Umständen
zu zerlegen.
Muiden
kuin
tässä
määriteltyjen
ohjaustoimintojen,
UNSICHTBARE LASERSTRAHLUNG DER KLASSE 2 IM
säätöjen ja toimintojen käyttö saattaa johtaa vaaralliseen
säteilyaltistumiseen.
Koska tässä cd-soittimessa käytetty lasersäde on silmille
vahingollinen, älä pura soitinta. Ainoastaan pätevä henkilökunta
saa huoltaa laitetta.
GERÄTEINNEREN VORHANDEN. NICHT IN DEN STRAHL SEHEN.
ATTENTION : RADIATIONS LASER VISIBLES ET INVISIBLES
DE CLASSE 2 OUAND OUVERT. NE PAS REGARDER
FIXEMENT LE FAISCEAU.
VARNING: KLASS 2 SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA
DEL ÄR ÖPPNAD. TITTA INTE IN I STRÅLEN.
HUOMIO: AVATTAESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE
LUOKAN 2 LASERSÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN.
ADVARSEL: KLASSE 2 SYNLIG OG USYNLIG LASERSTRÅLING HVIS DENNE
DELEN ÅPNES. STIRR IKKE INN I STRÅLEN.
ADVARSEL: KLASSE 2 SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING.
KIG IKKE IND I STRÅLEN.
Wenden Sie sich für Wartungsarbeiten nur an berechtigten
Fachhändler.
● OSTRZEŻENIE
Wykorzystanie elementów sterujących oraz wykonywanie
czynności innych niż opisano w niniejszej instrukcji może
● ATTENTION
Respecter les indications données relatives à la manipulation,
au réglage et au fonctionnement. En cas de non-respect,on
s’exposera à une radiation dangereuse.
spowodować
promieniowania.
narażenie
na
działanie
niebezpiecznego
Ponieważ wiązka lasera zastosowanego w tym odtwarzaczu
płyt CD jest niebezpieczna dla oczu, nie wolno samodzielnie
demontowaćobudowyurządzenia.Wszelkieczynnościserwisowe
należy zlecać osobom wykwalifikowanym.
Éviter absolument de démonter l’appareil, qui utilise un rayon
laser nuisible aux yeux. Pour toute réparation, s’adresser à une
personne qualifiée.
● PRECAUCIÓN
● CAUTION
El uso de los controles, ajustes o ejecución de procedimientos
distintos de los especificados podría causar la exposición a
radiación peligrosa.
Use of controls, adjustments or performance of procedures other
than those specified herein may result in hazardous radiation
exposure.
No intente desmontar la caja ya que el haz de láser usado en
este reproductor de discos compactos es perjudicial para los
ojos. Para el servicio de reparación, consulte a una persona
cualificada.
As the laser beam used in this compact disc player is harmful
to the eyes, do not attempt to disassemble the cabinet. Refer
servicing to qualified personnel only.
● OBSERVERA
Användning av reglage eller justeringar eller handhavande pĺ
annat sätt än som anges kan leda till farlig bestrĺlning.
Försök inte ta isär höljet eftersom CD-spelarens laserstrĺle
är skadlig för ögonen. Överlĺt service endast till kvalificerad
personal.
● ATTENZIONE
L’uso dei comandi e l’effettuazione di regolazioni e procedimenti
diversi da quelli specificati nel manuale possono provocare una
pericolosa esposizione alle radiazioni.
Poiché il raggio laser usato in questo giradischi puň danneggiare
gli occhi, non smontare l’apparecchio. Per le riparazioni rivolgersi
a personale specializzato.
● LET OP
Gebruik van regelaars, het maken van instellingen, gebruik of
handelingen anders dan in deze gebruiksaanwijzing vermeld, kan
gevaarlijke straling blootleggen.
De laserstraal in deze CD-speler kan de ogen beschadigen,
Probeer derhalve de ombouw niet te verwijderen. Laat reparaties
alleen over aan erkend onderhoudspersoneel.
● CUIDADO
O uso de controles, ajustes ou a execuçăo de procedimentos
além daqueles especificados aqui pode resultar em perigosa
exposiçăo à radiaçăo.
Como os raios laser usados neste player de CD săo perigosos
para os olhos, năo tente desmontar o aparelho. Solicite o
conserto somente para pessoas especializadas.
Download from Www.Somanuals.comiv. All Manuals Search And Download.
Informations sur la mise au rebut correcte
Información sobre la eliminación
Entsorgungsinformationen
A. Informations sur la mise au rebut à l’intention des
A. Información sobre eliminación para usuarios
A. Entsorgungsinformationen für Benutzer aus
utilisateurs privés (ménages)
particulares
Privathaushalten
1. Au sein de l’Union européenne
1. En la Unión Europea
1. In der Europäischen Union
Attention : si vous souhaitez mettre cet appareil au rebut,
ne le jetez pas dans une poubelle ordinaire!
Atención: si quiere desechar este equipo, ˇpor favor no
utilice el cubo de la basura habitual!
Achtung: Werfen Sie dieses Gerät zur Entsorgung bitte
nicht in den normalen Hausmüll!
Les appareils électriques et électroniques usagés doivent
être traités séparément et conformément aux lois en vigueur
en matière de traitement, de récupération et de recyclage
adéquats de ces appareils.
Los equipos eléctricos y electrónicos usados deberían
tratarse por separado de acuerdo con la legislación que
requiere un tratamiento, una recuperación y un reciclaje
adecuados de los equipos eléctricos y electrónicos
usados.
GemäßeinerneuenEU-Richtlinie, diedieordnungsgemäße
Rücknahme, BehandlungundVerwertungvongebrauchten
Elektro- und Elektronikgeräten vorschreibt, müssen
elektrische und elektronische Altgeräte getrennt entsorgt
werden.
Attention: votre
Atención: su producto
está marcado con
este símbolo.
Significa que los
productos eléctricos
y electrónicos
usados no deberían
mezclarse con los
residuos domésticos
generales.
Existe un sistema de
recogida indepen-
diente para estos
productos
Achtung: Ihr Produkt
trägt dieses Symbol.
Es besagt, dass
produit comporte ce
symbole. Il signifie
que les produits
Suite à la mise en oeuvre de ces dispositions dans les
Etats membres, les ménages résidant au sein de l’Union
européenne peuvent désormais ramener gratuitement*
leurs appareils électriques et électroniques usagés sur des
sites de collecte désignés.
Elektro- und Elektro-
nikgerä-te nicht mit
dem Haushaltsmüll
entsorgt, sondern
einem getrennten
Rücknahme- system
zugeführt werden
sollten.
Tras la puesta en práctica por parte de los estados
miembros, los hogares de particulares dentro de los
estados de la Unión Europea pueden devolver sus
equipos eléctricos y electrónicos a los centros de recogida
designados sin coste alguno *.
Nach der Einführung der Richtlinie in den EU-
Mitgliedstaaten können Privathaushalte ihre gebrauchten
Elektro- und Elektronikgeräte nun kostenlos an
ausgewiesenen Rücknahmestellen abgeben*.
In einigen Ländern* können Sie Altgeräte u.U. auch
kostenlos bei Ihrem Fachhändler abgeben, wenn Sie ein
vergleichbares neues Gerät kaufen.
*) Weitere Einzelheiten erhalten Sie von Ihrer
Gemeindeverwaltung.
Wenn Ihre gebrauchten Elektro- und Elektronikgeräte
Batterien oder Akkus enthalten, sollten diese vorher
entnommen und gemäß örtlich geltenden Regelungen
getrennt entsorgt werden.
électriques et
électroniques usagés
ne doivent pas être
mélangés avec les
déchets ménagers
généraux. Un
système de collecte
séparé est prévu pour
ces produits.
Dans certains pays*, votre détaillant reprendra également
gratuitement votre ancien produit si vous achetez un produit
neuf similaire.
En algunos países* es posible que también su vendedor
local se lleve su viejo producto sin coste alguno si Ud.
compra uno nuevo similar.
*) Veuillez contacter votre administration locale pour plus
de renseignements.
*) Por favor, póngase en contacto con su autoridad local
para obtener más detalles.
Si votre appareil électrique ou électronique usagé comporte
des piles ou des accumulateurs, veuillez les mettre
séparément et préalablement au rebut conformément à la
législation locale en vigueur.
Si sus equipos eléctricos o electrónicos usados tienen
pilas o acumuladores, por favor deséchelos por separado
con antelación según los requisitos locales.
En veillant à la mise au rebut correcte de ce produit, vous
contribuerez à assurer le traitement, la récupération et le
recyclage nécessaires de ces déchets, et préviendrez ainsi
les effets néfastes potentiels de leur mauvaise gestion sur
l’environnement et la santé humaine.
Al desechar este producto correctamente, ayudará a
asegurar que los residuos reciban el tratamiento, la
recuperación y el reciclaje necesarios, previniendo de esta
forma posibles efectos negativos en el medio ambiente
y la salud humana que de otra forma podrían producirse
debido a una manipulación de residuos inapropiada.
2. En otros países fuera de la Unión Europea
Si desea desechar este producto, por favor póngase en
contacto con las autoridades locales y pregunte por el
método de eliminación correcto.
Durch die ordnungsgemäße Entsorgung tragen Sie dazu
bei, dass Altgeräte angemessen gesammelt, behandelt
undverwertetwerden. Diesverhindertmöglicheschädliche
Auswirkungen auf Umwelt und Gesundheit durch eine
unsachgemäße Entsorgung.
2. Pays hors de l’Union européenne
2. In anderen Ländern außerhalb der EU
Si vous souhaitez mettre ce produit au rebut, veuillez
contacter votre administration locale qui vous renseignera
sur la méthode d’élimination correcte de cet appareil.
Suisse : les équipements électriques ou électroniques
usagés peuvent être ramenés gratuitement au détaillant,
même si vous n’achetez pas un nouvel appareil. Pour
obtenir la liste des autres sites de collecte, veuillez vous
Bitte erkundigen Sie sich bei Ihrer Gemeindeverwaltung
nach dem ordnungsgemäßen Verfahren zur Entsorgung
dieses Geräts.
Für die Schweiz: Gebrauchte Elektro- und Elektronikgeräte
können kostenlos beim Händler abgegeben werden,
auch wenn Sie kein neues Produkt kaufen. Weitere
Rücknahmesysteme finden Sie auf der Homepage von
Para Suiza: Los equipos eléctricos o electrónicos pueden
devolverse al vendedor sin coste alguno, incluso si no
compra ningún nuevo producto. Se puede encontrar una
lista de otros centros de recogida en la página principal de
B. Entsorgungsinformationen für gewerbliche Nutzer
1. In der Europäischen Union
B. Informations sur la mise au rebut à l’intention des
entreprises
B. Información sobre Eliminación para empresas
usuarias
Wenn Sie dieses Produkt für gewerbliche Zwecke genutzt
haben und nun entsorgen möchten:
1. Au sein de l’Union européenne
1. En la Unión Europea
Si ce produit est utilisé dans le cadre des activités de votre
entreprise et que vous souhaitiez le mettre au rebut:
Veuillez contacter votre revendeur SHARP qui vous
informera des conditions de reprise du produit. Les frais
de reprise et de recyclage pourront vous être facturés. Les
produits de petite taille (et en petites quantités) pourront
être repris par vos organisations de collecte locales.
Espagne: veuillez contacter l’organisation de collecte
existante ou votre administration locale pour les modalités
de reprise de vos produits usagés.
Si el producto se utiliza en una empresa y quiere
desecharlo:
Bitte wenden Sie sich an Ihren SHARP Fachhändler,
der Sie über die Rücknahme des Produkts informieren
kann. Möglicherweise müssen Sie die Kosten für die
Rücknahme und Verwertung tragen. Kleine Produkte (und
kleine Mengen) können möglicherweise bei Ihrer örtlichen
Rücknahmestelle abgegeben werden.
Por favor póngase en contacto con su distribuidor SHARP,
quien le informará sobre la recogida del producto. Puede
ser que le cobren los costes de recogida y reciclaje.
Puede ser que los productos de tamańo pequeńo (y las
cantidades pequeńas) sean recogidos por sus centros de
recogida locales.
Für Spanien: Bitte wenden Sie sich an das vorhandene
Rücknahmesystem oder Ihre Gemeindeverwaltung, wenn
Sie Fragen zur Rücknahme Ihrer Altgeräte haben.
2. In anderen Ländern außerhalb der EU
Para Espańa: por favor, póngase en contacto con el
sistema de recogida establecido o con las autoridades
locales para la recogida de los productos usados.
2. En otros países fuera de la Unión Europea
Si desea desechar este producto, por favor póngase en
contacto con sus autoridades locales y pregunte por el
método de eliminación correcto.
2. Pays hors de l’Union européenne
Bitte erkundigen Sie sich bei Ihrer Gemeindeverwaltung
nach dem ordnungsgemäßen Verfahren zur Entsorgung
dieses Geräts.
Si vous souhaitez mettre ce produit au rebut, veuillez
contacter votre administration locale qui vous renseignera
sur la méthode d’élimination correcte de cet appareil.
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Information om ĺtervinning
Informazioni per un corretto smaltimento
Informatie over verantwoorde verwijdering
A. Information om ĺtervinning av elektrisk utrustning
A. Informazioni sullo smaltimento per gli utenti
A. Informatie over afvalverwijdering voor gebruikers
för hushĺll
(privati)
(particuliere huishoudens)
1. EU-länder
1. Nell’Unione europea
1. In de Europese Unie
OBS! Kasta inte denna produkt i soporna!
Förbrukad elektrisk utrustning mĺste hanteras i enlighet
med gällande miljölagstiftning och ĺtervinningsföreskrifter.
I enlighet med gällande EU-regler ska hushĺll ha möjlighet
att lämna in elektrisk utrustning till ĺtervinningsstationer
utan kostnad.*
Attenzione: Per smaltire il presente dispositivo, non
utilizzare il normale bidone della spazzatura!
Le apparecchiature elettriche ed elettroniche usate devono
essere gestite a parte e in conformità alla legislazione che
richiede il trattamento, il recupero e il riciclaggio adeguato
dei suddetti prodotti.
Let op: Deze apparatuur niet samen met het normale
huisafval weggooien!
Afgedankte elektrische en elektronische apparatuur moet
gescheiden worden ingezameld conform de wetgeving
inzake de verantwoorde verwerking, terugwinning en
recycling van afgedankte elektrische en elektronische
apparatuur.
OBS! Produkten är
märkt med symbolen
ovan. Denna symbol
indikerar att elektro-
niska produkter inte
ska kastas i det vanliga
hushĺllsavfallet eftersom
det finns ett separat
avfallshanterings-sys-
tem för dem.
Attenzione: Il disposi-
tivo è contrassegnato
da questo simbolo,
che segnala di non
smaltire le apparec-
chiature elettriche ed
elettroniche insieme
ai normali rifiuti
domestici. Per tali
prodotti è previsto un
sistema di raccolta
a parte.
Let op: Uw product
is van dit merkteken
voorzien. Dit betekent
dat afgedankte
elektrische en elek-
tronische apparatuur
niet samen met het
normale huisafval
mogen worden weg-
gegooid. Er bestaat
een afzonderlijk
inzamelings- systeem
voor deze producten.
I vissa länder* kan det även hända att man gratis kan
lämna in gamla produkter till ĺterförsäljaren när man köper
en ny liknande enhet.
In seguito alle disposizioni attuate dagli Stati membri, i
privati residenti nella UE possono conferire gratuitamente
le apparecchiature elettriche ed elettroniche usate a centri
di raccolta designati*.
Na de invoering van de wet door de lidstaten mogen
particuliere huishoudens in de lidstaten van de Europese
Unie hun afgedankte elektrische en elektronische
apparatuur kosteloos* naar hiertoe aangewezen
inzamelingsinrichtingen brengen*.
In sommige landen* kunt u bij de aanschaf van een
nieuw apparaat het oude product kosteloos bij uw lokale
distributeur inleveren.
*) Neem contact op met de plaatselijke autoriteiten voor
verdere informatie.
Als uw elektrische of elektronische apparatuur batterijen
of accumulatoren bevat dan moet u deze afzonderlijk
conform de plaatselijke voorschriften weggooien.
Door dit product op een verantwoorde manier weg te
gooien, zorgt u ervoor dat het afval de juiste verwerking,
terugwinning en recycling ondergaat en potentiële
negatieve effecten op het milieu en de menselijke
gezondheid worden voorkomen die anders zouden
ontstaan door het verkeerd verwerken van het afval.
2. In andere landen buiten de Europese Unie
Als u dit product wilt weggooien, neem dan contact op
met de plaatselijke autoriteiten voor informatie omtrent de
juiste verwijderingsprocedure.
*) Kontakta kommunen för vidare information.
Om utrustningen innehĺller batterier eller ackumulatorer
ska dessa först avlägsnas och hanteras separat i enlighet
med gällande miljöföreskrifter.
In alcuni paesi*, anche il rivenditore locale puň ritirare
gratuitamente il vecchio prodotto se l’utente acquista un
altro nuovo di tipologia simile.
Genom att hantera produkten i enlighet med dessa
föreskrifter kommer den att tas om hand och ĺtervinnas pĺ
tillämpligt sätt, vilket förhindrar potentiella negativa hälso-
och miljöeffekter.
*) Per maggiori informazioni si prega di contattare l’autorità
locale competente.
Se le apparecchiature elettriche o elettroniche usate hanno
batterie o accumulatori, l’utente dovrà smaltirli a parte
preventivamente in conformità alle disposizioni locali.
Lo smaltimento corretto del presente prodotto contribuirà
a garantire che i rifiuti siano sottoposti al trattamento,
al recupero e al riciclaggio necessari prevenendone il
potenziale impatto negativo sull’ambiente e sulla salute
umana, che potrebbe derivare da un’inadeguata gestione
dei rifiuti.
2. Länder utanför EU
Kontakta de lokala myndigheterna och ta reda pĺ gällande
sorterings- och ĺtervinningsföreskrifter om du behöver
göra dig av med denna produkt.
B. Information om ĺtervinning för företag
1. EU-länder
Gör sĺ här om produkten ska kasseras:
Kontakta SHARPs ĺterförsäljare för information om hur
man gĺr till väga för att lämna tillbaka produkten. Det kan
hända att en avgift för transport och ĺtervinning tillkommer.
Mindre skrymmande produkter (om det rör sig om ett fĺtal)
kan eventuellt ĺterlämnas till lokala ĺtervinningsstationer.
2. Länder utanför EU
2. In paesi che non fanno parte dell’UE
Se si desidera eliminare il presente prodotto, contattare
le autorità locali e informarsi sul metodo di smaltimento
corretto.
Per la Svizzera: Le apparecchiature elettriche
o
elettroniche usate possono essere restituite gratuitamente
al rivenditore, anche se non si acquista un prodotto nuovo.
Altri centri di raccolta sono elencati sulle homepage di
Kontakta de lokala myndigheterna och ta reda pĺ gällande
sorterings- och ĺtervinningsföreskrifter om du behöver
göra dig av med denna produkt.
Voor Zwitserland:
U
kunt afgedankte elektrische en
elektronische apparatuur kosteloos bij de distributeur
inleveren, zelfs als
u
geen nieuw product koopt.
B. Informazioni sullo smaltimento per gli utenti
commerciali
Aanvullende inzamelingsinrichtingen zijn vermeld op de
B. Informatie over afvalverwijdering voor bedrijven
1. In de Europese Unie
1. Nell’Unione europea
Se il prodotto è impiegato a scopi commerciali, procedere
come segue per eliminarlo.
Als u het product voor zakelijke doeleinden heeft gebruikt
en als u dit wilt weggooien:
Contattare il proprio rivenditore SHARP che fornirà
informazioni circa il ritiro del prodotto. Potrebbero essere
addebitate le spese di ritiro e riciclaggio. Prodotti piccoli (e
quantitativi ridotti) potranno essere ritirati anche dai centri
di raccolta locali.
Per la Spagna: Contattare il sistema di raccolta ufficiale o
l’ente locale preposto al ritiro dei prodotti usati.
2. In paesi che non fanno parte dell’UE
Se si desidera eliminare il presente prodotto, contattare
le autorità locali e informarsi sul metodo di smaltimento
corretto.
Neem contact op met uw SHARP distributeur die
u inlichtingen verschaft over de terugname van het
product. Het kan zijn dat u een afvalverwijderingsbijdrage
voor de terugname en recycling moet betalen. Kleine
producten (en kleine hoeveelheden) kunnen door de lokale
inzamelingsinrichtingen worden verwerkt.
VoorSpanje:Neemcontactopmetdeinzamelingsinrichting
of de lokale autoriteiten voor de terugname van uw
afgedankte producten.
2. In andere landen buiten de Europese Unie
Als u dit product wilt weggooien, neem dan contact op
met de plaatselijke autoriteiten voor informatie omtrent de
juiste verwijderingsprocedure.
vi
Download from Www.Somanuals.com. All Manuals Search And Download.
Informaçăo sobre Eliminaçăo de Produtos
Tietoja laitteen hävittämisestä
Informacje dotyczące usuwania zużytego urządzenia
A. Informaçőes sobre a Eliminaçăo de Produtos
A. Hävitysohjeet käyttäjille (yksityiset kotitaloudet)
A.
Informacje
dla
użytkowników
dotyczące
(prywatne
usuwania
para os Utilizadores (particulares)
1. Euroopan unionissa
gospodarstwa
odpadów
domowe)
1. Na Uniăo Europeia
Huomio: Jos haluat hävittää tämän laitteen, älä käytä
tavallista jätesäiliötä.
Käytetyt sähkö- ja elektroniikkalaitteet pitää hävittää
erikseen noudattaen lainsäädäntöä, joka takaa käytettyjen
sähkö- ja elektroniikkalaitteiden oikean käsittelyn,
keräämisen ja kierrättämisen.
Atençăo: Se quiser eliminar este equipamento,
năo o deve fazer juntamente com o lixo doméstico
comum!
1. W krajach Unii Europejskiej
Uwaga: Jeśli chcą Państwo usunąć to urządzenie, prosimy
nie używać zwykych pojemników na śmieci!
O equipamento eléctrico e electrónico deve ser
tratado separadamente e ao abrigo da legislaçăo
aplicável que obriga a um tratamento, recuperaçăo e
reciclagem adequados de equipamentos eléctricos e
electrónicos usados.
Zużyty sprzęt elektryczny i elektroniczny należy usuwać
oddzielnie, zgodnie z wymogami prawa dotyczącymi
Atençăo: O seu produto
está identificado com este
símbolo. Significa que
os produtos
eléctricos e electrónicos
năo devem ser misturados
com o lixo doméstico
comum. Existe um sistema
de recolhas específico para
estes produtos.
Huomio:Tuote on
merkitty tällä symbo-
lilla.Tämä tarkoittaa,
että käytettyjä sähkö-
ja elektroniikkalaittei-
ta ei saa sekoittaa
kotitalouden yleisjät-
teiden kanssa. Näille
tuotteille on
Uwaga: Państwa
produkt oznaczony
jest tym symbolem.
Oznacza to, że
zużytego sprzętu
elektrycznego
i elektronicznego nie
należy łączyć z odpa-
dami z gospodarstw
domowych. Dla tego
typu produktów ist-
nieje odrębny system
zbiórki odpadów.
Jäsenvaltioiden täytäntöönpanoa seuraten yksityiset
kotitaloudet EU:n jäsenvaltioissa voivat palauttaa käytetyt
sähkö-jaelektroniikkalaitteetmäärättyihinkeräyspaikkoihin
ilmaiseksi*. Joissakin maissa* paikalliset vähittäismyyjät
voivat myös ottaa vastaan vanhan tuotteen ilmaiseksi, jos
asiakas ostaa vastaavan uuden tuotteen.
odpowiedniego przetwarzania, odzysku
i
recyklingu
zużytego sprzętu elektrycznego i elektronicznego.
Po wdrożeniu przepisów unijnych Państwach
w
Após a implementaçăo desta legislaçăo por parte dos
Estados-membros, todos os cidadăos residentes na
Uniăo Europeia poderăo entregar o seu equipamento
eléctrico e electrónico usado em estaçőes de recolha
específicas a título gratuito*.
Em alguns países* o seu revendedor local também
pode recolher o seu equipamento usado a título
gratuito na compra de um novo equipamento.
*) Contacte as entidades locais para mais
informaçőes.
Se o seu equipamento eléctrico e electrónico usado
funcionar a pilhas ou baterias, deverá eliminálas em
separado, conforme a legislaçăo local, e antes de
entregar o seu equipamento.
Członkowskich prywatne gospodarstwa domowe na
terenie krajów UE mogą bezpłatnie* zwracać zużyty sprzęt
elektryczny i elektroniczny do wyznaczonych punktów
zbiórki odpadów. W niektórych krajach* można bezpłatnie
zwrócić stary produkt do lokalnych punktów sprzedaży
detalicznej pod warunkiem, że zakupią Pasńtwo podobny
nowy produkt.
*) Pyydä lisätietoja paikallisviranomaisilta.
Jos käytetyissä sähkö- tai elektroniikkalaitteissa käytetään
paristoja tai akkuja, hävitä nämä tuotteet etukäteen
erikseen paikallisten säädösten mukaisesti.
olemassa erillinen
keräysjärjestelmä.
Hävittämällä tuotteen asiamukaisesti, autat varmistamaan,
että jätteet käsitellään, kerätään ja kierrätetään
asianmukaisella tavalla. Näin vältytään haitallisilta
ympäristö- ja terveysvaikutuksilta, joita saattaa olla
seuraamuksena jätteen epäasianmukaisesta käsittelystä.
2. Muissa maissa EU:n ulkopuolella
*)W celu uzyskania dalszych informacji na ten temat należy
skontaktować się z lokalnymi władzami.
Jeśli zużyty sprzęt elektryczny
i
elektroniczny jest
wyposażony w baterie lub akumulatory, należy je usunąć
oddzielnie, zgodnie z wymogami lokalnych przepisów.
Jeśli ten produkt zostanie usunięty we właściwy sposób,
pomogą Państwo zapewnić, że odpady zostaną
poddane przetworzeniu, odzyskowi i recyklingowi, a tym
samym zapobiec potencjalnym negatywnym skutkom
dla środowiska naturalnego i zdrowia ludzkiego, które
w przeciwnym razie mogłyby mieć miejsce na skutek
niewłaściwej obróbki odpadów.
Jos haluat hävittää tuotteen, ota yhteys paikallisiin
viranomaisiin ja pyydä ohjeita tuotteen asianmukaiseen
hävittämiseen.
Ao eliminar este produto correctamente estará
a contribuir para que o lixo seja submetido aos
processos de tratamento, recuperaçăo e reciclagem
adequados. Desta forma é possível evitar os efeitos
nocivos que o tratamento inadequado do lixo poderia
provocar no ambiente e na saúde.
B. Hävitysohjeet yrityskäyttäjille
2. Euroopan unionissa
Jos tuotetta on käytetty yrityskäytössä, ja haluat hävittää
sen,
2. Kraje pozaunijne
2. Em outros Países fora da UE
Oota yhteys SHARP-jälleenmyyjään, joka antaa sinulle
lisäohjeita tai ottaa tuotteen vastaan. Sinulta saatetaan
veloittaa tuotteen vastaanottamisesta ja kierrätyksestä
johtuvat kustannukset. Paikalliset keräyspisteet saattavat
ottaa vastaan pienet tuotteet (ja pienet määrät).
2. Muissa maissa EU:n ulkopuolella
Jeśli chcą Państwo pozbyć się produktu, należy
skontaktowaćsięzwładzamilokalnymiiuzyskaćinformacje
na temat prawidłowej metody usunięcia produktu.
Sequisereliminaresteproduto,contacteasentidades
locais e informese sobre o método correcto para
proceder à sua eliminaçăo.
Dotyczy Szwajcarii: Zużyte urządzenia elektryczne
i
Na Suíça: O equipamento eléctrico e electrónico
é aceite, a título gratuito, em qualquer revendedor,
mesmo que năo tenha adquirido um novo produto.
Poderá encontrar uma lista das estaçőes de recolha
destes equipamentos na página da Web www.
elektroniczne można zwrócić bezpłatnie do dostawcy, bez
konieczności zakupu nowego produktu. Adresy punktów
odbioru zużytego sprzętu można znaleźć na stronie www.
Jos haluat hävittää tuotteen, ota yhteys paikallisiin
viranomaisiin ja pyydä ohjeita tuotteen asianmukaiseen
hävittämiseen.
B. Informacje dla użytkowników biznesowych
dotyczące usuwania odpadów
B. Informaçőes sobre a Eliminaçăo de Produtos
para Utilizadores-Empresas
1. W krajach Unii Europejskiej
W
przypadku gdy produkt używany jest do celów
2. Na Uniăo Europeia
handlowych i zamierzają go Państwo usunąć:
Należy skontaktować się z dealerem firmy SHARP, który
poinformuje o możliwości zwrotu wyrobu. Być może
będą Państwo musieli ponieść koszty zwrotu i recyklingu
produktu. Produkty niewielkich rozmiarów (i w małej liczbie)
można zwrócić do lokalnych punktów zbiórki odpadów.
Dotyczy Hiszpanii: Skontaktuj się z punktem odbioru
lub władzami lokalnymi w sprawie oddania używanego
produktu.
Se o produto for usado para fins comerciais e quiser
eliminá-lo:
Contacte o seu revendedor SHARP que irá informá-lo
sobre a melhor forma de eliminar o produto. Poderá
ter de pagar as despesas resultantes da recolha
e reciclagem do produto. Alguns produtos mais
pequenos (e em pequenas quantidades) poderăo ser
recolhidos pelas estaçőes locais.
Na Espanha: Contacte o sistema de recolhas público
ou as entidades locais para mais informaçőes sobre
a recolha de produtos usados.
2. Kraje pozaunijne
Jeśli chcą Państwo usunąć ten produkt, należy
skontaktować się
z
władzami lokalnymi
i
uzyskać
2. Em outros Países fora da UE
informacje na temat prawidłowej metody jego usunięcia.
Sequisereliminaresteproduto,contacteasentidades
locais e informese sobre o método correcto para
proceder à sua eliminaçăo.
Download from Www.Somanuals.covmi.iAll Manuals Search And Download.
Information sur la mise au rebut de la pile
Informatie over afvalverwerking van batterijen
Information on Proper Disposal
Les piles/accus fournies avec ce produit peuvent contenir des traces de
Plomb.
De batterij die bij dit toestel geleverd wordt bevat sporen van Lood.
Voor EU: De doorgestreepte vuilnisbak op wieltjes duidt aan dat de
gebruikte batterijen niet mogen terechtkomen in het gewone huishoudelijke
afval. Er bestaat een gescheiden ophaalsysteem voor deze gebruikte
batterijen om eigen behandeling en recyclage volgens de wetgeving toe
te laten. Gelieve de locale autoriteiten te contacteren voor de details van
ophaling en recyclage.
A
.
Information on Disposal for Users (private
households)
Au sein de l’Union Européenne : Le symbole de la poubelle sur roues
barrée laisse supposer que les piles/accus usagées ne doivent pas être
mélangées avec les déchets ménagers! Il existe un mode de collecte séparé
pour les piles/accus usagées, ce qui permet d’effectuer un traitement et
un recyclage en accord avec la législation. Veuillez contacter une autorité
locale pour plus de renseignements sur le système mis en place.
Pour la Suisse : Les piles/accus usagées doivent être retournées chez votre
détaillant.
1. In the European Union
Attention: If you want to dispose of this equipment, please
do not use the ordinary dustbin!
Used electrical and electronic equipment must be treated
separately and in accordance with legislation that requires
proper treatment, recovery and recycling of used electrical
and electronic equipment.
Voor Zwitserland: De gebruikte batterij moet bij hetverkooppunt
teruggebracht worden.
Attention:Your prod-
uct is marked with
this symbol. It means
that used electrical
and electronic prod-
ucts should not be
mixed with general
household waste.
There is a separate
collection system for
these products.
Voor andere niet EU landen: Gelieve contact op te nemen met uw locale
autoriteiten voor de correcte methode van verwerking van de gebruikte
batterijen.
Following the implementation by member states, private
households within the EU states may return their used
electrical and electronic equipment to designated collection
facilities free of charge*.
Pour les pays hors Union Européenne : Veuillez contacter une autorité
locale afin de connaître la bonne méthode à utiliser pour la collecte de vos
piles/accus usagées.
Informaçăo sobre Eliminaçăo de Pilhas
In some countries* your local retailer may also take back
your old product free of charge if you purchase a similar new
one.
Información sobre la eliminación de la batería
A bateria fornecida com este produto contém traços de chumbo.
Para a Uniăo Europeia: O contentor de rodas traçado significa que as
baterias usadas năo deverăo ser colocadas junto com o lixo doméstico!
Existe um sistema de separaçăo próprio para baterias usadas, para
permitir um tratamento e reciclagem própria de acordo com a legislaçăo
em vigor. Por favor contacte as autoridades locais para mais detalhes nos
esquemas de recolha e reciclagem.
Las baterías suministradas con este producto contienen pequeńas
cantidades de Plomo.
*) Please contact your local authority for further details.
If your used electrical or electronic equipment has batteries
or accumulators, please dispose of these separately
beforehand according to local requirements.
Para EU: El contenedor de basura con ruedas tachado indica que las
baterías usadas no deberían mezclarse con los residuos domésticos
generales. Existe un sistema de recogida independiente de baterías
usadas, para permitir un correcto tratamiento y reciclado de acuerdo
con la legislación vigente. Por favor póngase en contacto con el sistema
de recogida establecido o con las autoridades locales para la recogida
selectiva de las baterías usadas.
By disposing of this product correctly you will help ensure
that the waste undergoes the necessary treatment, recovery
and recycling and thus prevent potential negative effects on
the environment and human health which could otherwise
arise due to inappropriate waste handling.
Para a Suíça: As baterias usadas deverăo ser devolvidas ao ponto de
venda.
Para os outros países fora da Uniăo Europeia: Por favor contacte a sua
autoridade local para o método correcto de disposiçăo das baterias
usadas.
Para Suiza: Las baterías usadas deben ser retornadas al punto de venta.
Para otros países fuera de la Unión Europea: Por favor póngase en contacto
con las autoridades locales para un correcto procedimiento de eliminación
de las baterías usadas.
2. In other Countries outside the EU
If you wish to discard this product, please contact your local
authorities and ask for the correct method of disposal.
For Switzerland: Used electrical or electronic equipment can
be returned free of charge to the dealer, even if you don’t
purchase a new product. Further collection facilities are
B. Information on Disposal for Business Users
1. In the European Union
Tietoja paristojen hävittämisestä
Tämän tuotteen mukana oleva paristo/akku saattaa sisältää jäänteitä Lyijy.
EU-maat: Paristo/akku on merkitty yliviivatun roskasäiliön symbolilla,
mikä tarkoittaa, että sitä ei saa hävittää kotitalouden yleisjätteiden kanssa.
Paristoille/akuille on olemassa erillinen keräysjärjestelmä, joka helpottaa
niiden asiamukaista käsittelyä ja lainmukaista kierrätystä. Ota yhteys
kuntaviranomaisiin saadaksesi lisätietoa keräyksestä ja kierrätyksestä.
Sveitsi: Käytetyt paristot/akut palautetaan ostopaikkaan.
Information om batteriavyttring
Batteriet som följer med denna produkt kan innehĺlla spĺr av Bly.
För EU: Batteriet är märkt med den överkorsade soptunnan vilket betyder
att det inte ska kastas i det vanliga hushĺllsavfallet. Det finns ett separat
insamlingssystem för batterier för att underlätta korrekt behandling och
ĺtervinning enligt gällande lagstiftning. Kontakta kommunen för vidare
information om insamling och ĺtervinning.
If the product is used for business purposes and you want
to discard it:
EU:n ulkopuoliset maat: Ota yhteys paikallisviranomaisiin saadaksesi
lisätietoa voimassa olevista lajittelu- ja kierrätyssäädöksistä ja ohjeet
käytetyn pariston/akun hävittämiseen.
För Schweiz: Använda batterier lämnas till inköpsstället.
För länder utanför EU: Kontakta de lokala myndigheterna för information
om gällande sorterings- och ĺtervinningsföreskrifter om du behöver göra
dig av med ett använt batteri.
Please contact your SHARP dealer who will inform you
about the take-back of the product. You might be charged
for the costs arising from take-back and recycling. Small
products (and small amounts) might be taken back by your
local collection facilities.
Informacja na temat usuwania baterii
Bateria dostarczana z tym produktem zawiera śladowe ilości ołowiu.
W krajach Unii Europejskiej: Przekreślony pojemnik na odpady oznacza,
że zużytych baterii nie należy wyrzucać do pojemników z odpadami
domowymi! Dla zużytych baterii istnieją oddzielne systemy zbiórki, które
zapewnią prawidłowe przetwarzanie i odzysk zgodnie z obowiązującym
prawem. Szczegóły na temat systemów zbiórki otrzymają Państwo u
lokalnych władz.
Informazioni sullo smaltimento della batteria
For Spain: Please contact the established collection system
or your local authority for take-back of your used products.
2. In other Countries outside the EU
La batteria fornita con questo prodotto contiene tracce di Piombo.
Per EU: Il cassonetto barrato indica che le batterie usate non devono
essere gettate assieme ai rifiuti domestici! Vi è un sistema di raccolta
differenziata per le batterie usate, che consente il loro corretto trattamento
e riciclo secondo quanto previsto dalle leggi vigenti. Vi prego di contattare
le locali autorità per i dettagli del sistema di raccolta e riciclaggio.
Per la Svizzera: Le batterie usate devono essere restituite al punto
vendita.
If you wish to discard of this product, please contact your
local authorities and ask for the correct method of disposal.
W Szwajcarii: Zużyte baterie można zwrócić w punkcie sprzedaży.
Kraje pozaunijne: W celu uzyskania szczegółowych informacji na temat
prawidłowej metody pozbycia się zużytych baterii, proszę o kontakt z
władzami lokalnymi.
Informationen zur Batterieentsorgung
Die für dieses Produkt mitgelieferte Batterie kann Spuren von Blei
enthalten.
Per altri Stati non-EU:Vi prego di contattare le autorità locali per conoscere
il metodo corretto di conferimento delle batterie usate.
Für die EU: Die durchgestrichene Abfalltonne bedeutet, dass
gebrauchte Batterien nicht mit dem Haushaltsmüll entsorgt
werden sollten! Es gibt getrennte Sammelsysteme für gebrauchte
Batterien, welche eine ordnungsgemäße Behandlung und
Verwertung entsprechend gesetzlicherVorgaben erlauben. Weitere
Einzelheiten erhalten Sie von IhrerGemeindeverwaltung.
Für die Schweiz: Die gebrauchte Batterie kann an derVerkaufsstelle
zurückgegeben werden.
Information on Battery Disposal
The battery supplied with this product contains traces of Lead.
For EU: The crossed-out wheeled bin implies that used batteries should
not be put to the general household waste! There is a separate collection
system for used batteries, to allow proper treatment and recycling in
accordance with legislation. Please contact your local authority for details
on the collection and recycling schemes.
Für andere Nicht-EU Staaten: Bitte erkundigen Sie sich bei Bedarf
bei Ihrer Gemeindeverwaltung nach weiteren Informationen zur
Entsorgung von gebrauchten Batterien.
For Switzerland:The used battery is to be returned to the selling point.
For other non-EU countries: Please contact your local authority for correct
method of disposal of the used battery.
viii
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGLISH
● XL-BD601PH BD Hi Fi Component System consisting of XL-BD601PH (main unit) and CP-BD601PH (speaker system).
Introduction
Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product.
Special Note:
Supply of this product does not convey a license nor imply any right to distribute content created with this product in revenue-generating broadcast systems (terrestrial, satellite, cable and/or other distribution
channels), revenue-generating streaming applications (via Internet, intranets and/or other networks), other revenue-generating content distribution systems (pay-audio or audio-on-demand applications and the like)
or on revenue-generating physical media (compact discs, digital versatile discs, semiconductor chips, hard drives, memory cards and the like). An independent license for such use is required. For details, please
MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS andThomson.
Accessories
The following accessories are included.
Adaptors for iPhone x 3
Remote control x ꢀ
“AAA” size battery (UM-4, R03, HP-ꢀ6 or similar) x 2
HDMI cable x ꢀ
FM aerial x ꢀ
Speaker wires x 2
Stand for iPad x ꢀ
CONTENTS
Auto power on function..............................................................................12
Auto power off function..............................................................................12
Treble control..............................................................................................13
General........................................................................................................ 3
Blu-ray Disc................................................................................................. 3
AC power connection.................................................................................10
Digital audio connection.............................................................................11
Line input connection (TV, etc.) ..................................................................11
Test of the remote control...........................................................................12
Turning the Power On.................................................................................12
Control Panel..............................................................................................17
Front panel .................................................................................................. 7
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ
Contents (continued)
Playback.................................................................................................... 41
Sound........................................................................................................ 42
Network..................................................................................................... 42
Condensation............................................................................................ 42
Accessing DLNA servers........................................................................... 23
iPhone playback........................................................................................ 35
Tuning........................................................................................................ 36
To recall a memorised station.................................................................... 37
To scan the preset stations........................................................................ 37
To recall stations in memory...................................................................... 38
Timer playback.......................................................................................... 39
General...................................................................................................... 43
BD player................................................................................................... 43
Tuner.......................................................................................................... 43
Function Control........................................................................................ 26
Settings ........................................................................................ 27
AudioVideo Settings ................................................................................. 27
AQUOS LINK............................................................................................. 28
Version....................................................................................................... 29
Headphones.............................................................................................. 40
Tuner.......................................................................................................... 41
iPod, iPhone or iPad.................................................................................. 41
Download from Www.Somanuals.com. All Manuals Search And Download.
E-2
●
Disc Durability – new breakthroughs in hard coating technologies gives
Blu-ray Discs the strongest resistance to scratches and finger prints.
Precautions
■ Volume control
The sound level at a given volume setting depends on speaker
efficiency, location, and various other factors. It is advisable to avoid
exposure to high volume levels. Do not turn the volume on to full
at switch on. Listen to music at moderate levels. Excessive sound
pressure from earphones and headphones can cause hearing loss.
■ Types of Discs/Media Formats that Can Be Used
■ General
withThis Unit
●
Please ensure that the equipment is positioned in a well ventilated area
and ensure that there is at least 10 cm (4”) of free space along the sides,
top and back of the equipment.
● The following discs can be played back in this Unit. Do not use an
8 cm to 12 cm adapter.
● Use discs that conform to compatible standards as indicated by
the presence of official logos on the disc label. Playback of discs
not complying with these standards is not guaranteed. In addition,
the image quality or sound quality is not guaranteed even if the
discs can be played back.
Precautions on viewing stereoscopic 3D images
● Do not view stereoscopic 3D images if you have a history of
photosensitivity, heart disease or poor health. This may cause
the symptoms to worsen.
● If you experience any health problems such as fatigue and
discomfort while viewing stereoscopic 3D images, immediately
discontinue viewing. Continuing viewing after symptoms appear
may cause health risks. Take a break until the symptoms have
completely disappeared.
● Ages of 5–6 or over are recommended for viewing stereoscopic
3D images. Symptoms such as fatigue and discomfort are
difficult to determine in young children, therefore they may
suddenly become ill. When viewing 3D images with children,
please watch for eye strain symptoms.
10 cm (4”)
10 cm (4”)
10 cm (4”)
DiscType
Recording
Format
Contents
Disc
Size
10 cm (4”)
● Use the unit on a firm, level surface free from vibration.
● Place the speakers at least 30 cm (12”) away from any CRT TV to
avoid colour variations across theTV screen. If the variations persist,
move the speakers further away from theTV. LCDTV is not prone to
such variation.
● Keep the unit away from direct sunlight, strong magnetic fields,
excessivedust, humidityandelectronic/electricalequipment(home
computers, facsimiles, etc.) which generate electrical noise.
● Do not place anything on top of the unit.
BD
Video
Region code —
B/ALL
Audio +
Video
(Movie)
12 cm
BD-RE DL
BD-R DL
BDMV/BDAV
format
●
When viewing stereoscopic 3D images, take a moderate break after
watching one title.Viewing for extended periods may cause visual strain.
DVD
Video
Region code Video format
2/ALL
Audio +
Video
(Movie)
12 cm
8 cm
●
Do not expose the unit to moisture, to temperatures higher than 60°C
(140°F) or to extremely low temperatures.
ALL
2
Precautions when cleaning this product
● Turn off the main power and unplug the AC power lead from the
wall socket before handling.
DVD+RW/DVD+R
DVD-RW/DVD-R
Video/VR/AVCHD Audio +
12 cm
8 cm
● If your system does not work properly, disconnect the AC power
lead from the wall socket. Plug the AC power lead back in, and
then turn on your system.
format (finalised
Video
DVD+R DL/DVD-R DL disc only)
DivX+HD
(Movie)
● To clean the outer cabinet, periodically wipe it with a soft cloth
(cotton, flannel, etc.).
●
In case of an electrical storm, unplug the unit for safety.
(H.264/MKV)
● For severe dirt, soak a soft cloth (cotton, flannel, etc.) in some
neutral detergent diluted with water, wring the cloth out thoroughly,
wipe off the dirt, then wipe again with a soft, dry cloth.
● Do not use chemicals or a chemically treated cloth for cleaning.
It may damage the cabinet finish.
● Hold the AC power plug by the head when removing it from the
wall socket, as pulling the lead can damage internal wires.
● The AC power plug is used as a disconnect device and shall always
remain readily operable.
● Do not remove the outer cover, as this may result in electric
shock. Refer internal service to your local SHARP service
facility.
● The ventilation should not be impeded by covering the ventilation
openings with items, such as newspapers, tablecloths, curtains,
etc.
Still image
(JPEG file)
J
JPEG
Audio
K
MP3
Audio CD
(CD-DA)
Audio
12 cm
8 cm
I
Audio CD
About MediaTypes
CD-RW/CD-R
Audio CD
(CD-DA)
Audio
■ Blu-ray Disc
Still image
(JPEG file)
J
JPEG
● No naked flame sources, such as lighted candles, should be
Blu-ray Disc is the ultimate next generation optical media format,
offering the following key features:
● Largest capacity (25 GB single layer – 50 GB dual layer) – with over 5
times the amount of content possible with current DVDs, particularly
well suited for high definition feature films with extended levels of
interactive features
placed on the apparatus.
Audio
K
MP3
● Attention should be drawn to the environmental aspects of battery
disposal.
Media Format
Recording Format
Contents
● This unit should only be used within the range of 5°C - 35°C (41°F
USB memory device DivX+HD
(H.264/MKV)
Audio +Video
(Movie)
- 95°F).
● Pristine picture quality with the capability for full high definition 1920
●
The apparatus is designed for use in moderate climates.
Still image
(JPEG file)
J
JPEG
x 1080p resolution
Warning:
● Best audio possible with uncompressed surround sound (higher
quality than even theatre audio)
The voltage used must be the same as that specified on this unit. Using
this product with a higher voltage other than that which is specified
is dangerous and may result in a fire or other type of accident causing
damage. SHARP will not be held responsible for any damage resulting
from use of this unit with a voltage other than that which is specified.
Audio
K
MP3
● Broadest industry support – ensuring more choice for consumers
● BD/DVD video units and discs have region codes, which dictate the
regions in which a disc can be played. This Unit’s region code is B
for BD and 2 for DVD. (Discs marked ALL will play in any unit.
in the marketplace
● Hardware products will be backward compatible with DVDs, allowing
continued enjoyment of existing DVD libraries.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-3
About MediaTypes (continued)
●
BD/DVD video operations and functions may be different from the
explanations in this manual and some operations may be prohibited
due to disc manufacturer’s settings.
of development and cannot guarantee support for future
enhancements or changes to the standard.
The following files cannot be played on this unit.
● When both Audio CD [CD-DA] format and JPEG/MP3 file formats
are recorded on a disc. (The disc is recognised to be an Audio CD
[CD-DA] only tracks in Audio CD [CD-DA] format are played back.)
● Multi-session discs cannot be played.
The following Audio CD*ꢀ discs cannot be played.
● If a menu screen or operating instructions are displayed during
● Discs containing a signal for the purpose of protecting copyrights
(copy control signal) may not be played back with this Unit.
● This Unit has been designed on the premise of playing back Audio
CDs that comply with CD (Compact Disc) standards.
The following CD-RW/R discs cannot be played.
● Discs on which data has not been recorded cannot be played
back.
● Discs recorded in a format other than an Audio CD and JPEG/MP3
file format cannot be played back.
● Discs may not be played back depending on their recording status
or the status of the disc itself.
playback of a disc, follow the operating procedure displayed.
Note:
About the DivX+HD (H.264/MKV) file format
● DivX playback may not be available depending on the DivX content
and file.
● Playback for some of the discs in the left side column tables may
not be possible depending on the disc.
● “Finalise” refers to a recorder processing a recorded disc so that
it will play in other DVD units/recorders as well as this unit. Only
finalised DVD discs will play back in this unit. (This unit does not
have a function to finalise discs.)
About files/folders for Still images (JPEG files) and audio data
(MP3 files)
You can play still images (JPEG files) /audio data (MP3 files) with this
unit by making folder(s) on discs or USB memory devices as shown
●
Some discs cannot be played back depending on the recording
format.
below.
Example of a folder structure:
Root
● DivX playback may not be available depending on the DivX content
● Discs may not be played back depending on their compatibility
with this Unit.
and file.
001.jpg/001.mp3
xxx.jpg/xxx.mp3
L
*2 About the JPEG file format
■
Discs that Cannot Be Used withThis Unit
JPEG is a type of file format for storing still-image files (photos,
illustrations, etc.). The Unit lets you play JPEG format still-image
files.
The following discs cannot be played back or will not play back
properly on this Unit. If such a disc is mistakenly played back, speaker
damage may occur. Never attempt to play back these discs.
L
File formats that are not compatible.
● Still images in formats other than JPEG (such as TIFF) cannot be
played.
● There may be some files that cannot be played even if they are in
JPEG format.
● Progressive JPEG files cannot be played.
● Moving image files as well as Motion JPEG format files cannot be
played, even though they are JPEG files.
001.jpg/001.mp3
01 Folder
Folder
CDG,Video CD, Photo CD, CD-ROM, CD-TEXT, SVCD, SACD, PD, CDV,
CVD, DVD-RAM, DVD-Audio, BD-RE with the cartridge, CD-WMA
256.jpg/256.mp3
Discs with unusual shapes cannot be played.
● Discs with unusual shapes (heart-shaped or hexagonal discs, etc.)
cannot be used. The use of such discs will cause malfunction.
001.jpg/001.mp3
255.jpg/255.mp3
L
The following BD video discs cannot be played.
● Discs not displaying “B” or “ALL” for the region code (discs sold
outside the authorised marketing area).*
Other files that cannot be played back.
● You may not be able to play some still images which you have
created, touched up, copied or otherwise edited on your
computer.
● Discs produced illegally.
001.jpg/001.mp3
256.jpg/256.mp3
xxx Folder
● Discs recorded for commercial use.
● You may not be able to play some still images you have processed
(rotated or saved by overwriting other images you have imported
from the Internet or e-mail).
L
*
The region code for this product is B.
The following DVD video discs cannot be played.
● Discs not displaying “2” or “ALL” for the region code (discs sold
outside the authorised marketing area).*
L
Including the root directory, the maximum number of folders and
files in each folder is limited to 256 in total.
You may experience one or more of the following symptoms
when playing files.
● Discs produced illegally.
●
It may take some time to play files depending on the number of folders,
number of files and volume of data involved.
File and folder requirements
● Discs recorded for commercial use.
●
The discs or USB memory devices which this unit can play back
(recognise) are limited to the following properties:
Contains EXIF format files (only JPEG files)
Picture resolution: Between 32 x 32 and 7680 x 4320 pixels (only
JPEG files)
*
The region code for this product is 2.
● EXIF information will not be displayed. EXIF stands for
Exchangeable Image File Format, and is a standard for storing
interchange information in image files, especially those using
The following BD-RE/R, DVD-RW/R and DVD+RW/R discs cannot
be played.
●
● Sharp cannot guarantee playback compatibility for all self-
recorded BD-discs because Blu-ray is a new and evolving format.
The playback compatibility will be affected by your choice of BD-
recorder, BD-disc and BD-burning software. Please always ensure
you are using the latest software versions on all units and contact
the individual manufacturers for further help if required.
Discs on which data has not been recorded cannot be played back.
*3 About the MP3 file format
Maximum number of folders and files in each folder: 256
Maximum hierarchy level of folders: 5
MP3 files are audio data compressed in the MPEG1/2 Audio layer-3
file format. “MP3 files” have “.mp3” as extensions. (Some files that
have “.mp3” extensions or files that have not been recorded in MP3
format will produce noise or cannot be played.)
File size: 20 MB or less (JPEG files)
200 MB or less (MP3 files)
Note:
Playing the MP3 file format
● File and folder names displayed on this unit may differ from those
To avoid inconveniences, please check the playback compatibility
of your self-recorded disc before you purchase this BD-unit.
For maximum playback compatibility of self-recorded BD-discs
Sharp recommends that the BDMV/BDAV standards are used. If a
playback issue occurs after purchase, please download the latest
software version for your BD-unit from the Sharp internet page or
ask your Sharp-Dealer.
● The MP3 files are not played in the order they were recorded.
● It is recommended to record data at a lower speed as data
recorded at a fast speed can produce noise and may not be able
to be played.
displayed on PCs.
● The more folders there are, the longer the reading time.
● Depending on the folder tree, reading MP3 files can take time.
● The playing time may not be correctly displayed during MP3 file
playback.
This BD-unit uses the latest technology available at the time
Download from Www.Somanuals.com. All Manuals Search And Download.
E-4
About MediaTypes (continued)
ABOUT DivX VIDEO
1
3
2
■ The Icons Used inThis Operation Manual
● DivX® is a digital video format created by DivX, Inc. This is an
official DivX Certified® device that plays DivX video.Visit divx.com
for more information and software tools to convert your files into
DivX video.
1. English
2. Chinese
1. English
2. Chinese
2
2
.............. Indicates the functions that can be performed
for BDVideo discs.
BD VIDEO
BD-RE
4
5
.............. Indicates the functions that can be performed
for BD-RE discs.
DivX Certified® to play DivX® and DivX Plus™ HD (H.264/MKV) video
up to 1080p HD including premium content.
1 23
4 56
.............. Indicates the functions that can be performed
for BD-R discs.
BD-R
16:9 LB
2
ABOUT DivX VIDEO-ON-DEMAND
........... Indicates the functions that can be performed
DVD VIDEO
●
This DivX Certified® device must be registered in order to play
purchased DivX Video-on-Demand (VOD) movies. To obtain your
registration code, locate the DivX VOD section in your device setup
menu. Go to vod.divx.com for more information on how to complete
your registration.
DVDVideo BDVideo
Audio tracks and audio formats
BD and DVD discs can contain up to 8 separate tracks with a
different language on each. The first in the list is the original track.
This section also details the audio format of each soundtrack —
Dolby Digital, DTS, MPEG etc.
for DVDVideo discs.
1
.............. Indicates the functions that can be performed
for DVD-RW discs.
DVD-RW
DVD-R
AUDIO CD
CD-R
.............. Indicates the functions that can be performed
for DVD-R discs.
■ About Disc Contents
.............. Indicates the functions that can be performed
for Audio CDs.
Dolby Digital
A sound system developed by Dolby Laboratories Inc. that gives
movie theatre ambience to audio output when the Unit is connected
to a Dolby Digital processor or amplifier.
BD Video
.............. Indicates the functions that can be performed
for CD-R discs.
Enjoy BD-specific functions including BONUSVIEW (BD-ROM Profile
For the BD video discs compatible with BONUSVIEW/BD-LIVE, you
can enjoy additional contents by copying the data from the discs or
downloading it via the Internet. For instance, this function is capable
of playing the original movie as the primary video while playing video
commentary from the film director on a small screen as a secondary
video.
.............. Indicates the functions that can be performed
for CD-RW discs.
CD-RW
USB
DTS
DTS is a digital sound system developed by DTS, Inc. for use in
cinemas.
Linear PCM
Linear PCM is a signal recording format used for Audio CDs and on
some DVD and Blu-ray discs.The sound on Audio CDs is recorded
at 44.1 kHz with 16 bits. (Sound is recorded between 48 kHz with
16 bits and 96 kHz with 24 bits on DVD video discs and between
48 kHz with 16 bits and 192 kHz with 24 bits on BD video discs.)
Subtitle languages
This indicates the kind of subtitles.
Screen aspect ratio
Movies are shot in a variety of screen modes.
.............. Indicates the functions that can be performed
for USB memory devices.
........... Indicates the functions that can be performed
for iPod, iPhone and iPad.
iPod
Note:
● The available functions differ depending on the disc.
Title, Chapter andTrack
2
3
4
● Blu-ray discs and DVDs are divided into “Titles” and “Chapters”.
If the disc has more than one movie on it, each movie would be a
separate “Title”. “Chapters”, on the other hand, are subdivisions
of titles. (See Example 1.)
● Audio CDs are divided into “Tracks”.You can think of a “Track” as
one tune on an Audio CD. (See Example 2.)
Example 1: Blu-ray disc or DVD
Camera angle
Recorded onto some BD/DVD discs are scenes which have been
simultaneously shot from a number of different angles (the same
scene is shot from the front, from the left side, from the right side,
etc.).
5
Region code
This indicates the region code (playable region code).
Title 1
Title 2
Chapter 1
Chapter 2
Track 2
Chapter 3
Track 3
Chapter 1
Example 2: Audio CD
Track 1
Track 4
Icons Used on BD/DVD Video Disc Cases
The back of the case of a BD/DVD that is commercially available
usually contains various information about the contents of the disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-5
Important Information
When condensation forms:
● “Made for iPod,” “Made for iPhone,” and “Made for iPad” mean
that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards. Please note that
the use of this accessory with iPod, iPhone, or iPad may affect
wireless performance.
■ Disc Precautions
● It becomes difficult for the Unit to read the signals on the disc
and prevents the Unit from operating properly.
Be Careful of Scratches and Dust
To remove condensation:
● BD, DVD and CD discs are sensitive to dust, fingerprints and
especially scratches. A scratched disc may not be able to be played
back. Handle discs with care and store them in a safe place.
Proper Disc Storage
● Take out the disc and leave the Unit with the power off until
the condensation disappears. Using the Unit when there is
condensation may cause malfunction.
Place the disc in the centre of the disc case
and store the case and disc upright.
■ License and Copyright
Audio-visual material may consist of copyrighted works which must
not be recorded without the authority of the owner of the copyright.
Refer to relevant laws in your country.
● “This item incorporates copy protection technology that is
protected by U.S. patents and other intellectual property rights
of Rovi Corporation. Reverse engineering and disassembly are
prohibited.”
Avoid storing discs in locations subject to
direct sunlight, close to heating appliances or
in locations of high humidity.
Do not drop discs or subject them to strong
vibrations or impacts.
● Manufactured under license from Dolby Laboratories. “Dolby” and
the double-D symbol are trademarks of Dolby Laboratories.
● Manufactured under license under U.S. Patent Nos: 5,956,674;
5,974,380; 6,226,616; 6,487,535; 7,392,195; 7,272,567; 7,333,929;
7,212,872 & other U.S. and worldwide patents issued & pending.
DTS-HD, the Symbol, & DTS-HD and the Symbol together are
registered trademarks & DTS-HD Master Audio | Essential is a
trademark of DTS, Inc. Product includes software. © DTS, Inc. All
Rights Reserved.
Avoid storing discs in locations where there
are large amounts of dust or moisture.
Handling Precautions
● If the surface is soiled, wipe gently with a soft, damp (water only)
cloth. When wiping discs, always move the cloth from the centre
hole toward the outer edge.
●
is a trademark of DVD Format/Logo Licensing Corporation.
● “HDMI, the HDMI logo and High-Definition Multimedia Interface
are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.”
● Do not use record cleaning sprays, benzene, thinner, static
electricity prevention liquids or any other solvent.
● Do not touch the surface.
● Do not stick paper or adhesive labels to the disc.
● If the playing surface of a disc is soiled or scratched, the Unit may
decide that the disc is incompatible and eject the disc tray, or it
may fail to play the disc correctly. Wipe any dirt off the playing
surface with a soft cloth.
● “x.v.Colour” and “x.v.Colour” logo are trademarks of Sony
Corporation.
● Java and all Java-based trademarks and logos are trademarks
or registered trademarks of Sun Microsystems, Inc. in the United
States and/or other countries.
● “AVCHD” and the “AVCHD” logo are trademarks of Panasonic
Corporation and Sony Corporation.
● Blu-rayDisc™,Blu-ray™,Blu-ray3D™,BD-Live™,BONUSVIEW™,
and the logos are trademarks of the Blu-ray Disc Association.
● YouTube is a trademark of Google Inc.
Cleaning the Pick Up Lens
● Never use commercially available cleaning discs. The use of these
discs can damage the lens.
● DivX®, DivX Certified®, DivX PlusTM HD and associated logos are
trademarks of DivX, Inc. and are used under license.
● LC_LCFONT+ and LC logo mark are
registered trademarks of SHARP Corporation. This product is
embedded with LC Font technology, which was developed by
SHARP Corporation for clearly displaying easy-to-read characters
on an LCD screen. However, other non-LCD fonts are used for
displaying some screen pages.
● Request the nearest service centre approved by SHARP to clean
the lens.
Warnings about dew formation
● Condensation may form on pick up lens or disc in the following
conditions:
– Immediately after a heater has been turned on.
– In a steamy or very humid room.
– When the Unit is suddenly moved from a cold environment to
a warm one.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-6
Controls and indicators
1 2
3
5
6
7
4
8
9
10
11 12 13 14 15
■ Front panel
Page
Page
ꢀ. Remote sensor...................................................................................................................................ꢀ2
2. Timer indicator...................................................................................................................................39
3. DiscTray..............................................................................................................................................ꢀ8
4. Docking Station for iPod or iPhone .................................................................................................35
5. Volume Control ..................................................................................................................................ꢀ2
6. ON/STAND-BY Button .....................................................................................................ꢀ8, 35, 36, 42
7. SELECTOR Button.....................................................................................................ꢀꢀ, ꢀ3, ꢀ8, 22, 35
8. USB 2Terminal ...............................................................................................................................9, ꢀ3
9. Audio In Socket............................................................................................................................ꢀꢀ, 40
ꢀ0. Headphone Socket...........................................................................................................................40
ꢀ3. Disc/USB/iPod/iPhone/iPad Stop Button ................................................................................22, 36
ꢀ4. Disc/USB/iPod/iPhone/iPad Play or Pause Button.................................................................22, 36
ꢀ5. DiscTray Open/Close Button .................................................................................................... ꢀ2, ꢀ8
3
9
■ Display
■ Speaker system
1
2
4
5 6 7
8
10
Page
ꢀ. Dome-Tweeter
2. Woofer
3. Bass Reflex Duct
4. SpeakerTerminal
3
4
1
2
ꢀ. MEM (Memory) Indicator
2. Repeat Indicator
3. Play/Pause Indicator
11
5. FM Stereo Mode Indicator......................................................37
6. Stereo Station Indicator..........................................................37
9. TP Indicator .............................................................................37
ꢀ0. TA Indicator..............................................................................37
ꢀꢀ. Muting Indicator
12 13 14
15
16 17 18
19
■ Speaker grilles are removable
Make sure nothing comes into contact with the
speaker diaphragms when you remove the speaker
grilles.
ꢀ3. Title Indicator
ꢀ4. Artist Indicator
ꢀ5. Album Indicator
ꢀ6. Track Indicator
ꢀ9. Sleep Indicator ........................................................................40
Download from Www.Somanuals.com. All Manuals Search And Download.
E-7
Controls and indicators (continued)
1
■ Remote Control
Page
ꢀ. Remote ControlTransmitter........................................................................................................ꢀ2, 42
2. Clock/Timer Button ...............................................................................................................ꢀ3, 39, 40
3. Sleep Button.......................................................................................................................................40
4. Numeric Buttons..........................................................................................................................ꢀ4, 40
5. ON/STAND-BY Button .................................................................................................................ꢀ3, 39
6. iPod <TV OUT> Button................................................................................................................35, 36
7. Disc Button.............................................................................................................................ꢀ8, 22, 23
8. Tuner Button........................................................................................................................... 36, 37, 38
9. Volume Up/Down Button...................................................................................................................ꢀ2
ꢀ0. Mute Button .......................................................................................................................................ꢀ2
ꢀꢀ. Top Menu/Title List Button .........................................................................................................ꢀ9, 36
ꢀ2. Tuner Preset Up Button, iPod/iPhone Cursor Up Button................................................... 27, 29, 36
ꢀ3. Tuning Down,Time Down Button ................................................................................... ꢀ3, 27, 29, 36
ꢀ4. Enter Button ..........................................................................................................................ꢀ3, ꢀ8, 20
ꢀ5. Tuner Preset Down Button, iPod/iPhone Cursor Down Button......................................... 27, 29, 36
ꢀ6. Exit Button..............................................................................................................................2ꢀ, 22, 23
ꢀ7. Play Mode Button ..............................................................................................................................26
ꢀ8. Stop Button .....................................................................................................................ꢀ8, 2ꢀ, 22, 36
ꢀ9. Red (A) Button..............................................................................................................................20, 23
20. Green (B) Button ....................................................................................................................20, 2ꢀ, 30
2ꢀ. 3D Button............................................................................................................................................ꢀ6
22. Home Button..........................................................................................................................2ꢀ, 22, 24
23. Picture in Picture Button...................................................................................................................ꢀ9
24. Child Lock Button................................................................................................................................8
25. Audio/RDS ASPM Button..................................................................................................................38
26. Subtitle / RDS PTY Button ...............................................................................................................38
27. Open/Close Button......................................................................................................................2ꢀ, 22
28. Function <Setup> Button............................................................................................................25, 26
29. Display <DIM> Button ....................................................................................................ꢀ2, ꢀ8, 25, 37
30. TV (ARC) Button...........................................................................................................................ꢀ2, ꢀ6
3ꢀ. Input Button .................................................................................................................................ꢀꢀ, 40
32. BassTreble (X-BASS) Button ......................................................................................................ꢀ2, ꢀ3
34. Pop-Up Menu Button.........................................................................................................................ꢀ8
35. Tuning Up,Time Up Button ............................................................................................. ꢀ3, 27, 29, 36
36. Return/Demo Button.......................................................................................................ꢀ0, 2ꢀ, 23, 30
37. Play Button................................................................................................................. ꢀ6, ꢀ7, 20, 23, 36
38. Pause Button..........................................................................................................................22, 23, 36
39. Blue (D) Button.......................................................................................................................20, 23, 30
40. Yellow (C) Button....................................................................................................................20, 23, 30
4ꢀ. TV Power Button................................................................................................................................ꢀ3
42. TV Input Button..................................................................................................................................ꢀ3
43. TV Volume Up Button ........................................................................................................................ꢀ3
44. TV Channel Up Button.......................................................................................................................ꢀ3
45. TV Volume Down Button ...................................................................................................................ꢀ3
46. TV Channel Down Button..................................................................................................................ꢀ3
2
27
28
3
5
4
29
6
7
8
30
31
32
33
9
10
11
34
12
13
35
36
14
15
16
17
18
37
38
19
20
21
22
23
24
25
26
39
40
41
42
43
44
45
46
Keylock function
You can set the keylock to prevent accidental operations.
This function allowsTVs compatible with AQUOS LINK to also perform a Key Lock on the unit.
● To activate this function, press and hold CHILD LOCK button. ”CHILD LOCK ON” will appear
● To deactivate, press and hold CHILD LOCK button. ”CHILD LOCK OFF” will appear
● If you try to operate the unit while the keylock function is set, “CHILD LOCK” appear on the front
display panel to indicate that the keylock function is set.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-8
System connections
Make sure to unplug the AC power lead before making any connections.
Right
speaker
FM aerial
TV
Video cable
(not supplied)
To video input socket (for iPod video connection only)
Left
speaker
Red
Wall socket
(AC 220 - 240V ~ 50/60 Hz)
HDMI cable
To HDMI input terminal
External FM aerial:
Use an external FM aerial (75 ohms coaxial cable) for better reception.
Front
■ USB ꢀ, USB 2 terminals and Video Out socket
When an external FM aerial is used, disconnect the supplied FM
aerial wire.
Rear
USB 2
Terminal
Note:
Placing the aerial on the unit or near the AC power lead may cause
noise pickup. Place the aerial away from the unit for better reception.
USB 1
Terminal
■ Speaker connection
VIDEO OUT
socket
● Connect the wire without insulation tube to
the minus (–) terminal, and the wire with red
insulation tube to the plus (+) terminal.
USB 2 terminal:
This terminal is only for iPod, iPhone and iPad. It does not support
USB memory device.
HDMITerminal
● Use speakers with an impedance of 6 ohms
HDMI terminal:
USB ꢀ terminal:
or more, as lower impedance speakers can
This terminal supports DISC function (BD, DVD, CD and USB 1), TV
ARC and AQUOS LINK.
This terminal is only for USB memory devices to support music,
video, photo and memory expansions for BD-LIVE.
VIDEO OUT socket:
damage the unit.
Incorrect
●
Do not mistake the right and the left channels. The
right speaker is the one on the right side when you
face the unit.
■ Aerial connection
This socket is only for iPod and iPhone video out connection.
● Do not let the bare speaker wires touch each other.
● Do not allow any objects to fall into or to be placed in the bass
reflex ducts.
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 socket and position the
FM aerial wire in the direction where the strongest signal can be
received.
● Do not stand or sit on the speakers.You may be injured.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-9
System connections (continued)
■ Demonstration mode
■ Connecting to an amplifier/AV receiver
You can connect this unit to an amplifier/AV receiver to enjoy digital
surround sound. With this unit, the audio connection can be made
using HDMI connection depending on the capabilities of the amplifier/
AV receiver you connect.
● The first time the unit is plugged in, the unit will enter the
demonstration mode.
● To cancel the demonstration mode, press the RETURN/DEMO
button (remote control) during power stand-by mode. The unit will
enter the low power consumption mode.
● To return to the demonstration mode, press the RETURN/DEMO
button again.
Note:
● Be sure to turn off this Unit and the equipment before making any
connections.
●
If iPod or iPhone is docked, the unit will begin charging. “Charge Mode”
will be displayed. Demonstration mode is invalid during charge mode.
■ Connecting iPod or iPhone toTV
HDMI cable
(supplied)
Photo and video files from iPod or iPhone can be viewed by connecting
the system toTV/monitor.
If theTV/monitor has a video input, connect it to the iPodVIDEO OUT
socket at the back of the unit and set the TV Out on the iPod or
Note:
ToTV HDMI (ARC) input
terminal
Please make sure to set iPod unit to either NTSC or PAL to match your
TV signal. Please visit Apple’s homepage for further information.
HDMI
cable
■ AC power connection
After checking all the connections have been made correctly, plug the
AC power lead of this unit into the wall socket.
Note:
Projector
TV
Unplug the AC power lead from the wall socket if the unit will not be
in use for a prolonged period of time.
Notes:
● In this unit, “HDMI Video Out” is set to “Auto” as a default (See
with “HDMI Video Out” set to “Auto”, select the output resolution
which corresponds to the connected equipment.
■ HDMI connection (TV, projector)
TV
HDMI cable
Amplifier/
You can enjoy high quality digital picture and sound using an HDMI cable.
(OnlyTVs/projectors with an HDMI terminal can be connected to this unit.)
When using HDMI ARC (Audio Return Channel) Connection
When this unit is connected to TV, there might be a necessity to
adjust theTV menu.
Refer the operation manual of the respectiveTV, concerning ARC.
In case of incompatibility between this unit and your TV HDMI ARC,
please use the analog or digital connection. (Refer Line In and Digital
AV receiver
●
This unit supports HDMI which enables ARC (Audio Return Channel).
● To enable ARC make sure to use High Speed HDMI cable.
● This structure also needsTV that supports ARC.
● To enjoy 3D images, connection to a 3D compatibleTV is needed.
● For connection to a TV/projector, refer to the TV/projector’s
operation manual.
Notes:
● When using an HDMI output, 7.1 ch Digital Output is available.
● Audio transmitted in DTS-HD High Resolution Audio and DTS-HD
Master Audio formats is output from the HDMI terminal as Bitstream.
Connect an amplifier with a built-in decoder to enjoy the fine sound
quality.
After connecting
● When a connection to a 3DTV is made via an amplifier/AV receiver, it
● Prepare the desired disc or content and start playback. (Pages
When you use AQUOS LINK orTV ARC, make sure to use a certified
HDMI cable.
is necessary to connect to a 3D compatible amplifier/AV receiver.
ꢀ� Be sure to turn off this Unit and the TV/projector before making
any connections.
2� Firmly connect an HDMI cable to the HDMI OUT (TV ARC) terminal
on this unit (1) and the HDMI IN terminal of theTV/projector (2).
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ0
System connections (continued)
To select Line In function:
■ Digital audio connection
■ Broadband Internet Connection
● On main unit: Press SELECTOR button repeatedly until Line In is
displayed.
You can connectTV unit or other similar device using an optical digital
audio cable (commercially available).
By connecting this unit to the Internet, you can enjoy a variety of
content on your TV using BD-LIVE functions, video on-demand
services (e-Contents), home networks and also perform software
updates. In this unit, the Internet connection can be made using
wired connection (LAN cable)
● On remote control: Press INPUT button repeatedly until Line In is
displayed.
■ Wired connection (LAN cable)
Notes:
Connect a LAN cable (commercially available) to the ETHERNET
terminal of this unit (1) and the LAN port of the broadband router
(2).
● Be sure to turn off this Unit and the equipment before making any
connections.
Caution:
● When using a broadband Internet connection, a contract with an
Internet service provider is required. For more details, contact your
nearest Internet service provider.
● Refer to the operation manual of the equipment you have as the
connected equipment and connection method may differ depending
on your Internet environment.
Optical digital
cable*
TV unit or other similar device
* Commercially available
After connecting
■ Subwoofer pre-out connection
●
● Prepare the desired disc or content and start playback. (Pages
You can connect a subwoofer with an amplifier to the SUBWOOFER
PRE OUT socket.
LAN cable*
Commercially available subwoofer
Audio cable
(commercially
available)
(amplifier built in)
■ Line input connection (TV, etc.)
Audio signal
Connect to theTV using an audio cable.
To audio input
TV
To audio input
socket
socket
PC
To SUBWOOFER
PRE OUT socket
LAN
Audio cable
(commercially
available)
Main unit
Notes:
Internet
Modem
Broadband router
● No sound is heard from the subwoofer without a built-in amplifier.
● Subwoofer Pre-out (audio signal): 200mV / 10k ohms at 70 Hz.
* Commercially available
Notes:
●
Use a LAN cable/router supporting 10BASE-T/100BASE-TX.
● SHARP cannot guarantee that all brands’ broadband routers will
To LINE input
sockets
Main unit
operate with this unit.
After connecting
●
● When enjoying video on-demand services (e-Contents), see pages
● To play back files via the Home Network, see page 23.
● To update the software via the Internet, perform Software Update
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀꢀ
Remote control
General control
■ Display brightness control
To dim the display brightness, press and hold the DISPLAY <DIM>
button on the remote control for more than 2 seconds.
● The display brightness will change each time the DISPLAY <DIM>
button is pressed for more than 2 seconds.
■ Battery installation
ꢀ� Open the battery cover.
2� Insert the supplied battery according to the terminal indicated in
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display gets dimmer).
(Display is bright).
the battery compartment.
3� When inserting or removing the battery, push it towards the (–)
battery terminals.
4� Close the cover.
■ Volume auto fade-in
If you turn off and on the main unit with the volume set to 80 or higher, the
volume starts at 40 and fades in to the last set level.
■ Volume control
Caution:
Turn the volume knob towards VOLUME +/– (on main unit) or press
VOL. +/– (on remote control) to increase or decrease the volume.
●
Replace all old batteries with new ones at the same time.
● Do not mix old and new batteries.
■ Speaker output selection (HDMI connection)
● Remove the battery if the unit will not be used for a long period of
time. This will prevent potential damage due to battery leakage.
● Do not use rechargeable battery (nickel-cadmium battery, etc.).
● Installing the battery incorrectly may cause the unit to
malfunction.
■ Turning the Power On
By using HDMI connection, you have an option to listen to the sound
output either from this unit or yourTV.
To select the preferred speaker output, press and hold TV (ARC)
button on the remote control until “TV Speaker” or “BD601 Speaker”
appears on the display.
Press ON/STAND-BY on the remote control or on the main unit to
turn on the power.
Entering standby
Press ON/STAND-BY on the remote control or on the main unit to
enter standby.
●
Batteries (battery pack or batteries installed) shall not be exposed to
excessive heat such as sunshine, fire or the like.
■ Auto power on function
Notes: concerning use:
Note:
When you press any of the following buttons, the unit turns on.
● iPod <TV OUT>, DISC, INPUT, TUNER, TV (ARC) on the remote
control: Selected function is activated.
● Replace the battery if the operating distance is reduced or if the
operation becomes erratic. Purchase two “AAA” size batteries
(UM-4, R03, HP-16 or similar).
● When you turn on this unit for the first time after purchase or
when you turn on this unit after you perform “System Reset” (see
●
/
or OPEN/CLOSE button on the main unit: The unit turns on
● Periodically clean the transmitter on the remote control and the
and playback of the last function will start (DISC, TUNER, USB-2
(iPod), iPod, AUDIO IN, LINE IN, DIGITAL IN, TV ARC)
sensor on the unit with a soft cloth.
●
If you press ON/STAND-BY again immediately after entering standby,
the Unit may not turn on. If this happens, wait for 10 seconds or more
and then turn on the power again.
● Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.
■ Auto power off function
About the Home screen
When turning on the unit on DISC function, the Home screen appears.
Home screen
The main unit will enter the stand-by mode (when iPod or iPhone is not
docked) after 15 minutes of inactivity during:
iPod/USB-2 (iPod): No connection.
● Keep the remote control away from moisture, heat, shock, and
vibrations.
DISC: In the stop mode.
■ Test of the remote control
AUDIO IN/LINE IN/DIGITAL IN/ TV ARC: No detection of input signal
or very low sound audibility
Video
BD-Video
USB
Check the remote control after checking all the connections.
Point the remote control directly at the remote sensor on the unit.The remote
control can be used within the range shown below:
Music
Note:
However, if iPod or iPhone is docked, the unit will begin charging.
“Charge Mode” will be displayed.
1
Picture
e-Contents
Settings
Home Network
Remote sensor
■ Muting
The volume is muted temporarily when pressing the
remote control. Press again to restore the volume.
button on the
Select
ENTER
EXIT
Enter
Return
Exit
0.2 m - 6 m
(8” - 20’ )
2 3 4
5
■ X-Bass control
1 Main menu
When the power is first turned on, the unit will enter the extra bass
mode which emphasises the bass frequencies, and X-BASS ON will
appear.To cancel the extra bass mode, press and hold BASS/TREBLE
[X-BASS] button on the remote control.
2 Icon for disc inserted
3 Icon for USB memory device connected
4 Icon for LAN connection
5 Button Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ2
4�Press the
or
button to select 24-hour or 12-hour display and
General control (continued)
English
Deutsch
Français
Italiano
Español
Português
Note:
Nederlands
Svenska
Dansk
Norsk
Suomi
Česky
Magyar
Slovensky
Slovenščina
then press the ENTER button.
The 24-hour display will appear.
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
■ Bass control
ꢀ� Press the BASS/TREBLE [X-
2� WBAitShSin] b5utstoencotondsse,lecptre“sBsastsh”e.
Polski
VOLUME (+ or –) button to
adjust the bass.
........
↔ + 4 ↔ + 5
5�To adjust the hour, press the
ENTER button. Press the or
by 1 hour. Hold it down to advance continuously.
or
or
button and then press the
- 5 ↔ - 4
button once to advance the time
● To select the DVD disc language, such as subtitle language, etc.,
■ Treble control
6�To adjust the minutes, press the
button and then press the
ENTER button. Press the or button once to advance the time by
1 minute. Hold it down to advance the time by 10 minutes interval.
■ Operating aTV Using the Remote Control
ꢀ�Press the BASS/TREBLE [X-BASS]
2�bWuitthtoinn 5tosseecloencdt s“T,rperbelses”.theVOLUME (+
The Universal Remote Control may operate the basic functions of the
SHARPTV.
TV function control
To confirm the time display:
Press the CLOCK/TIMER button. The time display will appear for
about 10 seconds.
........
↔ + 4 ↔ + 5
- 5 ↔ - 4
or –) button to adjust the treble.
Note:
■ Function Selector
● TV Power: POWER
When power supply is restored after unit is plugged in again or after a
● TV-AV Selector: INPUT
When the SELECTOR button on main unit is pressed, the current
function will change to different mode. Press the SELECTOR button
repeatedly to select desired function.
● TVVolume up/down: VOL e/f
● TV Channel up/down: CH r/s
To readjust the clock:
Perform “Setting the clock” from step 1. If the “Clock” does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour display)
will be skipped.
Audio In
Line In
TV (ARC)
DISC
To change the 24-hour or ꢀ2-hour display:
USB-2
(iPod)
Digital In
iPod
FM MONO
FM STEREO
ꢀ�Clear all the programmed contents. [Refer to “Factory reset, clearing
Note:
The backup function will protect the memorised function mode for
a few hours should there be a power failure or the AC power lead
becomes disconnected.
2�Perform “Setting the clock” from step 1 onwards.
Before Starting Playback
Setting the clock (Remote control only)
■ Language Setting
Changing the on-screen display language
ꢀ�At the Home Screen, press
/
to select “Settings”, then press or
ENTER.
2�Press
/
to select “On Screen Language”, then press or ENTER.
Audio Video Settings
Smart Settings
Video
AQUOS LINK
Playback Setting
Music
On Screen Language
Communication Setup
Picture
Version
USB Memory Management
e-Contents
In this example, the clock is set for the 24-hour (0:00) display.
ꢀ�Press the ON/STAND-BY button to turn the power on.
2�Press the CLOCK/TIMER button.
Software Update Settings
Settings
System
3�Press
/
to select the language you want to display on the
3�Within 10 seconds, press the ENTER button. To adjust the day,
screen, then press ENTER.
press the
or
button and then press the ENTER button.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ3
Before Starting Playback (continued)
WhilstholdingdowntheTVPOWERbutton,enterthemanufacturer
setting number (3 digits) with the direct number buttons.
● Check the TV setting number to change the TV manufacturer
■ To change theTV manufacturer setting
Manufacturer/Brand
Set-Up Code Number
CORONADO
CRAIG
143
043 054 028
164
● After setting, check it operates properly.
ON/STAND-BY
CROSLEY
CROWN
043 143
Manufacturer/Brand
ADMIRAL
Set-Up Code Number
072 081 160 161 096
006 004 101 143 011 072 081 120
164
CURTIS MATHES
CXC
Direct number
buttons
ADVENT
AIKO
247
103
043
076 103 055 004 127 143 016 043 044
125 120
DAEWOO
006 146 248 150 157 167 078 184 185
255
AKAI
DAYTRON
004 143
041 142
011
ALARON
028
DELL
AMARK
112 143
DENON
AMERICA ACTION
AMPRO
043
DIGITAL PROJECTION
DUMONT
224
073
004 073
102 104 161
043
ANAM
043 054 055 056 080 112
DWIN
AOC
058 006 004 112 121
DYNASTY
APEX
227
DYNATECH
DYNEX
062
APEX DIGITAL
AQUAVISION
ASTAR
015 226 037
145
148
FISHER
007 057
001
189
ELECTROBAND
ELECTROGRAPH
ELECTROHOME
ELEMENT
AUDIOVOX
AVION
076 103 043 035 145 197
TV
POWER
182
219
024 076 143
084 190
BAYSONIC
BELL&HOWELL
BENQ
043
072
005 028 043 048 076 096 155 004 051
143 151 153 154 213
EMERSON
241
EPSON
026 235
BRADFORD
BROKSONIC
CANDLE
043
ESA
078
096
FUJITSU
FUNAI
164 028 198 246 066 138
028 043 052 249
043
006 002 003 004
Notes:
CAPEHART
CARVER
058
●
Some models of Sharp’sTVs may not be operable.
● As for manufacturers with 2 or more setting numbers, test them to
FUTURETECH
GATEWAY
164
select the right number.
242 078
CELEBRITY
CETRONIC
CINERAL
CITIZEN
001
● Registering the manufacturer number deletes the number
previously memorised.
● Whenreplacingthebatteriesoftheremotecontrol,themanufacturer
number may return to default. In this case, register it again.
● The manufacturer number cannot be registered depending on the
TV. Even if the number can be set, some buttons may not work.
006 073 144 160 161 004 008 009
034 056 074 091 155 081 120
043
GE
103 120
GEM
078
006 002 003 004 101 103 143
GIBRALTER
GOLDSTAR
GRUNPY
HAIER
004 073
CLASSIC
CONCERTO
CONTEC
043
004 106 119 110 112 113 127 143
004
028 043
084 196
043 051
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ4
Before Starting Playback (continued)
Manufacturer/Brand
Set-Up Code Number
Manufacturer/Brand
Set-Up Code Number
Manufacturer/Brand
QUASAR
Set-Up Code Number
034 056 250
006 003 004 022 059 060 061 063
064 127 164 094 160 028 035
HALL MARK
004
046
028
164
043
MAGNAVOX
HANNSPREE
HARLEY DAVIDSON
HARMAN KARDON
HARVARD
RADIO SHACK
004 019 127 143 043
124 181 215
160 161 144 156 065 006 004 023 024
056 074 152 081 233
RCA
MAJESTIC
MARANTZ
MATSUI
072
164 006 230 231
REALISTIC
RUNCO
007 019
164
072 073 050 137 169
006 004 058 242
HISENSE
170 179
MATSUSHITA
MEGATRON
MINTEK
080
SAMPO
163 004 007 009 011 072 010 012 023
075 143 158 166 254 232
HITACHI
004 101 127 133 143 160 089 105 211
228 229
004
SAMSUNG
HP
027 039 214 085
108 168
SANSEI
SANSUI
SANYO
120
109 024 042 004 040 146 028 081
225
HUMAX
HYPERION
HYUNDAI
ILO
069
MITSUBISHI
096 145 255
253
MOTOROLA
MTC
081
007 053 057 082 020
049 067
006 004 062 101
SCEPTRE
SCOTCH
SCOTT
036
183 145
MULTITECH
NAD
043
004
INFINITY
INFOCUS
INSIGNIA
INKEL
164
015 025
004 005 028 043 048 143 191
068 092 097 240
004 007 015 028 030 057 082 094 143
160 052 164
NIKO
220
SEARS
024 145 147 148 149 180 244 128
NEC
004 006 016 019 040 109 134 167
129
073
164
001
SEMIVOX
SEMP
043
NORCENT
NUVISION
OLEVIA
124
INTEQ
JBL
015
221
SHARP
081 014 019 028 004 022 143 175
216 084 132
080
JCB
SHERWOOD
SIGNATURE
SONY
100
OPTIMUS
OPTOMA
ORION
004 006 008 024 030 065 101 143 156
160
072
JCPENNEY
029 032
096
001 126 139 252
JENSEN
JVC
013
SOUNDESIGN
SOYO
003 004 028 043
038 001 034 083 206 159
PANASONIC
080 098 243 251
086
006 003 004 024 056 059 060 063
064 127 143 164
164 005 038 093 127 006 003 004
059 210 215 161 239
023 025 135 176 004 018 006 209 234
118 131 140
015 077 078 079 070 177 178 190 199
200 212
KENWOOD
KLEGG
KLOSS
KONKA
KREISEN
KTV
006 001
182
PHILCO
SPECTRICON
SPECTRONIQ
SQUAREVIEW
SSS
112
193 195
052
PHILIPS
002 059
180
PIONEER
POLAROID
004 043
043
090
STARLITE
SUNBRITETV
SUPRE MACY
SUPREME
SVA
006 043 143 154
245
004 106 119 110 112 113 127 143 084
223
PORTLAND
PRISM
004 143 103
LG
002
034
LODGENET
LOEWE
LOGIK
072
001
PROSCAN
PROTON
PROTRON
PROVIEW
144 160 161
207 164
079
004 058 143 171 173 112 086
130 141 192 193 195
190
006 003 059 060 063 064 127 160 164
044 249 213 238
072
SYLVANIA
LUXMAN
LXI
004
SYMPHONIC
052 249
007 015 052 081 160 164
SYNTAX OLEVIA
216 084 132
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ5
Before Starting Playback (continued)
■ Using AQUOS LINK
■ Using 3D
Manufacturer/Brand
TANDY
Set-Up Code Number
081
This sets output of 3D images.
To view 3D images, playback of 3D content (3D BD video) is necessary
with a 3D compatibleTV and 3D glasses in addition to this unit.
Controlling the unit using AQUOS LINK
What is AQUOS LINK?
Using the HDMI CEC (Consumer Electronics Control), with AQUOS LINK
you can interactively operate this unit with your SHARP AQUOSTV.
TATUNG
056 062
034 080
028
TECHNICS
TECHNOL ACE
TECHVIEW
TECHWOOD
What you can do with AQUOS LINK
099
When you connect this unit to the LCD TV compatible with AQUOS
LINK using an HDMI cable, you can perform the functions listed
Press 3D to change to the 3D mode.
● Each time the button is pressed, the mode switches between
“Auto(3D)” and “2D”.
004
002 003 004 024 028 043 072 101 143
103 164
Automatic input select function
TEKNIKA
● The status of the selected mode will be displayed on the TV
When you start playback of this unit, the input selector of the LCDTV
will automatically switch to the LCD TV input terminal connected to
the unit and the playback image will appear on the screen, even if you
are watching aTV programme.
screen.
TELEFUNKEN
TELERENT
TERA
255
Auto:Video signals are output as 3D when 3D content (3D BD video)
is played or as 2D when 2D content is played.
2D: Even if 3D content (3D BD video) is played, video signals are
output as 2D at all times.
072
172
Automatic power off function
Turning off the LCD TV under different condition will set this unit as
below:
TMK
004
● This setting (Auto(3D)/2D) can also be performed using the menu
TNCI
073
Notes:
Condition
DISC function
TV(ARC) function
Other functions
Unit will turn off automatically
YES (during stop mode only)
YES
TOSHIBA
TOTEVISION
TRUTECH
UNIVERSAL
VIDEO CONCEPTS
VIDIKRON
VIDTECH
VIEWSONIC
VIORE
015 030 007 040 062 101 045
143
● The 3D mode can be switched only when playback is stopped.
●
Depending on the connectedTV, the images during playback may switch
to 2D images due to changes in the resolution, etc. Make sure the 3D
image setting is performed on theTV.
087
008 009
NO
(iPod/USB-2 (iPod)/Tuner/Audio
● The 3D images may not be output as set in “HDMIVideo Out”.
● When performing Fast Forward/Reverse, images are shown in 2D.
Caution:
● When viewing 3D images, viewing for a long period of time or lying
on your back may cause eye strain and discomfort. In addition, 3D
images may affect the eyesight of young children/infants, so keep
them from viewing the images.
In/Line In/Digital In)
146
174 188 164 050
Automatic power on function
When you switch to the LCDTV input terminal connected to this unit,
the power of this unit will be turned on automatically.
004
122
AQUOS PURE MODE
183 236
190
When you connect this unit to an AQUOS LCD TV compatible with
AQUOS LINK and set “AQUOS LINK” to “Yes”, images automatically
adjusted to the most suitable image quality for the AQUOS TV are
output from the HDMI OUT terminal of this unit.
VISCO
VITO
084
Note:
VIZIO
078
● In order to make AQUOS LINK available, set “AQUOS LINK” to
004 064 164 008 009 019 028 060 061
063 072 074 143
WARDS
Refer to the Operation Manual of theTV for details regarding setup.
WESTING HOUSE
WINBOOK
YAMAHA
076 036 001 217 218
■ Audio Return Channel (ARC) (Audio Return
031
Channel submenu)
004 006 115 116 162 165
The audio return channel (ARC) enables an HDMI ARC-capableTV to
send the audio stream to the HDMI OUT socket of this unit.To use this
function, pressTV (ARC) button on the remote control.
YORK
004
YUPITERU
ZENITH
043
072 073 095 103 011 096
112
ZONDA
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ6
Before Starting Playback (continued)
Control Panel
Major functions of each button icon
■ Control Panel
This function allows you to operate this unit using the TV remote
control by displaying the control panel on theTV screen.
● To operate this function, connect this unit to aTV compatible with
HDMI CEC (Consumer Electronics Control) using an HDMI cable
operations.
● Display the pop-up menu screen for BD video
POP-UP
MENU
TOP MENU
TITLE LIST
POP-UP
MENU
FUNC.
and the menu screen for DVD video.
● Display the top menu screen for BD video and
TOP MENU
TITLE LIST
DVD video.
Notes:
● Display the Function Control screen for BD
● The control panel may not be displayed depending on theTV. Also,
it may not be available depending on the content.
● When operating using the remote control of the unit, the control
panel does not appear.
FUNC.
video, DVD video, etc.
● Fast reverse (search).
● Play.
● When playing video on demand streaming content available with
this unit, the control panel cannot be displayed.
ꢀ� Switch the TV input to the input source to which this unit is
connected (HDMI input).
PANEL
OFF
Select
Enter
2� Press the PLAY button on theTV remote control.
●
The control panel appears on theTV screen.
● Fast forward (search).
● Skip to the beginning of a chapter.
● Pause.
●
When there is no operation for approximately 10 seconds, the
control panel disappears automatically.
To display the control panel, press the PLAY button on the TV
remote control.
3� Press
button icon, then press ENTER.
The function of the selected button icon is available.
/
/
/
on the TV remote control to select the desired
●
● Skip to the next chapter.
● Jump backward (approx. 10 seconds). (This
function is used when you want to re-watch a
scene that has just been shown.)
● Stop.
● Jump ahead (approx. 30 seconds).
● Turn off the control panel.
PANEL
OFF
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ7
Video/Picture/Music Playback
ꢀ� Load a disc.
● Each time you press DISPLAY <DIM>, the display switches as
■ Loading a Disc
follows.
●
●
●
Playback may begin automatically, depending on the disc.
Playback begins from the first title.
BD-VIDEO
1
The menu may be displayed first, depending on the disc.
Perform playback operation by following the directions on the
screen.
Disc Information
screen A
2
1/1
3
4
1/101
00:00:12
/03:12:28
●
When loading a disc containing 3D content (3D BD video) with
be stopped and the 3D notice will be displayed on the TV screen.
In such cases, press ENTER for confirmation, and then playback
will start.
ON/STAND-BY
OPEN/CLOSE
2� Press I if playback does not begin automatically or playback is
00:00:12
/03:12:28
4
Disc Information
screen B
stopped.
Note:
● The disc load time may vary depending on the disc.
ꢀ� Press ON/STAND-BY to turn on the power.
2� Press DISC button on the remote control or SELECTOR button
repeatedly on the main unit to select DISC function.
3� Press OPEN/CLOSE to open the disc tray.
4� Load a disc on the disc tray.
Regarding playback of BD video discs
● Some of the newly released BD video discs cannot be played back
unless you update the unit software to the latest version.Therefore,
it may be required to update the software of the unit.
updates for the unit.
No Display
Type of disc
Title number being played /Total number ofTitles
Chapter number being played /Total number of Chapters
Elapsed playback time /Total playback time for theTitle
1
2
3
4
●
●
Insert the disc with the label face up.
In case of disc recorded on both sides, face down the side to play back.
To stop playback
Notes:
Press H.
● Disc Information Screen A disappears after about 1 minute elapses
without performing any operations.
Resume playback function
●
If you press I next, playback will resume from the point where the unit
was previously stopped.To playback from the beginning, cancel resume
mode by pressing H, then press I. (This may not work depending on
the type of disc. In this case, open the disc tray or enter standby.)
● For some commercially-released BD VIDEO discs, the total
playback time display for the Chapter/Title may not appear.
■ BD/DVD Menus
5� Press OPEN/CLOSE to close the disc tray.
Notes:
●
Resume playback may not function depending on the disc.
● This section explains how to play back a BD/DVD video disc with
a top menu, disc menu or pop-up menu.
■ BD/DVD Video Playback
● The resume playback function for discs will be cancelled if video
on demand streaming content is viewed after disc playback. Disc
playback will start from the beginning after viewing streaming
content.
● The titles listed in the top menu and a disc guide (for options like
BD VIDEO
BD-RE
DVD-R
BD-R
subtitles and audio languages) are given in the disc menu.
DVD VIDEO
DVD-RW
Displaying the disc information
This section explains playback of commercially available BD Video
and DVDVideo discs (like movies) and recorded DVD-RW/R discs.
●
This unit supports DVD upscaling during DVD playback.
● For a description of other playback functions, refer to “Playback
Press DISPLAY <DIM> during playback.
Start playback by selecting a title from the top menu
BD VIDEO DVD VIDEO
ꢀ� Press TOP MENU/TITLE LIST.
●
The top menu screen is displayed if present on the BD/DVD
video disc.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ8
Video/Picture/Music Playback (continued)
Example
Example
When formatting a USB memory device using a PC, perform the
following settings.
T O P M E N U
Pop-up menu
–
–
Format File System: FAT32
Allocation Unit Size: Default Allocation Size
1
3
2
Jazz
Latin
Previous page
Next page
● Do not use a USB extension cable when connecting a USB
memory device to the USB terminal of the unit.
4
Classic
Rock
–
Using a USB extension cable may prevent the unit from
performing correctly.
2� Press
/
/
/
to select the desired item, then press ENTER.
2� Press
/
/
/
to select the title, then press ENTER.
The selected title is played back.
Use of Picture in Picture function (secondary audio/video
playback)
BD-Video that includes secondary audio and video compatible with
Picture in Picture can be played back with secondary audio and video
simultaneously as a small video in the corner.
3� Press POP-UP MENU to exit.
●
●
The pop-up menu will automatically disappear for some
discs.
Note:
● The procedure explained on this page is the basic operation
procedure. Procedures vary depending on the BD/DVD video disc,
so you may need to follow the instructions in the BD/DVD video
disc manual or the instructions displayed on the screen.
■ Enjoying BONUSVIEW or BD-LIVE
BD VIDEO
Top menu
● With some BD/DVD discs, the top menu may be referred to as the
“Title Menu”. Use TOP MENU/TITLE LIST on the remote control
when the instructions refer to “Title Menu”.
● If no top menu is available, the TOP MENU/TITLE LIST button will
have no effect.
This Unit is compatible with additional functions of BD-Video, BONUSVIEW
(BD-ROM Profile 1Version 1.1) and BD-LIVE.
For BD-Video discs compatible with BONUSVIEW, the functions of Picture
in Picture andVirtual Package are available. For BD-LIVE compatible discs,
you can enjoy a variety of functions via the Internet in addition to the
BONUSVIEW functions.
ꢀ� Press PinP during playback to show the 2-picture screen.
Using the disc menu
Virtual Package/BD-LIVE data is saved in Local Storage (USB
memory device connected to this Unit). To enjoy these functions,
connect a USB memory device (2GB or greater) supporting USB 2.0
High Speed (480Mbit/s) to the USB1 terminal on this unit.
● USB memory device can be used only on USB 1 terminal. (When
you insert or remove a USB memory device, be sure to turn the
main power off and make sure that “Quick Start” is set to “No”
DVD VIDEO
Example: Select “SUBTITLE LANGUAGE”.
ꢀ� Press TOP MENU/TITLE LIST.
●
The disc menu screen is displayed if present on the DVD video
disc.
2� Press
/
to select “SUBTITLE LANGUAGE”, then press
Primary audio/
video
2� To remove the secondary video, press PinP again.
Secondary
audio/video
ENTER.
Rear
●
The screen for selecting the subtitle language is displayed.
Example
Notes:
USB1
terminal
● To listen to secondary audio, make sure that “Secondary Audio” is
● The secondary audio and video for Picture In Picture may
automatically play back and be removed depending on the content.
Also, playable areas may be restricted.
MENU
1
2
3
AUDIO LANGUAGE
SUBTITLE LANGUAGE
AUDIO
USB memory device
Virtual Package
● If there is insufficient storage space, the data will not be copied/
downloaded. Delete unneeded data or use a new USB memory
device.
For BD-Video discs compatible with Virtual Package, data is copied
from the discs or Internet to local storage. It is automatically copied
to the local storage prior to playback. You can enjoy a variety of
additional functions including secondary video, secondary audio,
subtitles, movie trailers, etc.
● The playback methods vary depending on the disc. For details,
refer to the disc manual.
3� Press
/
to select the subtitle language, then press ENTER.
4� Press TOP MENU/TITLE LIST to exit.
● If a USB memory device containing other data (previously recorded)
is used, the video and audio may not play back properly.
● If the USB memory device is disconnected from this unit during
playback of Virtual Package/BD-LIVE data, playback of the disc
will stop.
Using the pop-up menu
BD VIDEO
ꢀ� Press POP-UP MENU during playback.
BD-LIVE
●
Some time may be required for the data to load (read/write).
●
●
The pop up menu screen is displayed.
Virtual Package data and the BD-LIVE data in the USB memory
device.
In this Unit, a variety of contents with interactive functions are
available through BD-LIVE compatible Blu-ray discs by connecting
to the Internet. You can enjoy the download of bonus features such
as latest movie trailers to the USB memory device, communication
compatible BD-J interactive games, etc.
The menu contents displayed vary depending on the disc. For
details on how to see and operate the pop-up menu, refer to
the manual for the disc.
Notes:
● SHARP cannot guarantee that all brands’ USB memory devices
will operate with this unit.
● The available functions differ depending on the disc.
● Only USB memory devices formatted with FAT 32/16 are
compatible.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-ꢀ9
Video/Picture/Music Playback (continued)
Notes:
Playback by selecting a title
Thumbnail
● Regarding playback method of BD-LIVE contents, etc., perform
the operations in accordance with the instructions in the BD disc
manual.
ꢀ� Load a recorded disc.
Program 1
●
TheTitle List screen is displayed.
1
Example:Thumbnail screen
● To enjoy BD-LIVE functions, perform the broadband Internet
● Before using this function, please read “Network Service
contents.
● If the BD-LIVE screen does not appear for a while after you select
the BD-LIVE function in the BD disc menu, the USB memory device
may not have enough free space. In such cases, eject the disc from
the unit, and then erase the data in the USB memory device in the
21/5 Fri 9:30 AM 110 Min.
Program 1
Program
1
Program
2
Program
3
21/5 Fri 9:30 AM 110 Min.
Program
4
Program
5
Program
6
Program
1
Program
2
Program
3
EXIT
Select
Enter
Return
Playlist
Exit
Functions
Program
4
Program
5
Program
6
3
1
A
B
C
D
Title Name
By Chapter
EXIT
Select
Title Name
Enter
By Chapter
Return
Playlist
Exit
Functions
■ DVD-R/-RW (VR format) / BD-RE/-R (BDAV format)
A
B
C
D
Title Name
Playback
●
●
If the Title List screen is not displayed, press TOP MENU/
TITLE LIST.
Program 1
DVD-R DVD-RW
BD-RE
BD-R
When loading a BD disc with usage restrictions placed by a
BD recorder, the password input screen appears. Then, input
your password.
21/5 Fri 9:30 AM 110 Min.
1 Program 1
You can play back a recorded disc (DVD:VR format finalised disc only
/ BD: BDAV format disc only).
● For a description of other playback functions, refer to ”Playback
21/5 Fri 110 Min.
15/6 Fri 110 Min.
3/7 Mon 56 Min.
18/9 Thu 40 Min.
20/9 Sat 20 Min.
25/9 Thu 60 Min.
Program
1
2 Program 2
3 Program 3
4 Program 4
5 Program 5
6 Program 6
If you input a wrong password three times, the disc tray will
open. Close the disc tray, and then input a correct password.
2
3
2� Press
/
/
/
to select the desired title, then press ENTER to
start playback.
●
●
If you want to select additional titles, switch pages by pressing
1/All 8 Titles
T or U.
EXIT
Select
Thumbnail
Enter
Return
Playlist
Exit
Functions
You can playback by pressing A (Red) instead of pressing
A
B
C
D
Sorting
ENTER.
3� Press H to stop playback.
1 Information of selected title
2 Title Name
Note:
● The Title List screen also can be displayed by pressing TOP
Recording Date
MENU/TITLE LIST when playback is stopped.
Recording Duration
3 Button Guide
Playback by selecting a chapter
AboutTitle List
● The Title List can be displayed in two types, Thumbnail and Title
Name.
● Each time you press A (Red), the screen changes between
Thumbnail andTitle Name.
ꢀ� Press B (Green) while theThumbnail screen is displayed.
●
The chapter screen is displayed.
CHAPTER
1
CHAPTER
2
CHAPTER
3
CHAPTER
4
CHAPTER
5
CHAPTER
6
Notes:
●
“Finalise” refers to a recorder processing a recorded disc so that it will
play in other DVD units/recorders as well as this unit. Only finalised DVD
discs will play back in this unit. (This unit does not have a function to
finalise discs.)
●
●
If you want to select additional chapters, switch pages by
pressing T or U.
To return to theThumbnail screen, press B (Green).
● Some discs cannot be played back depending on the audio
format.
● BD-RE/-R discs recorded from a BD recorder comply with AACS
copyright protection technology. As this unit is not intended to be
compliant with AACS, such discs cannot be played back.
(AACS: Advanced Access Content System)
2� Press
to start playback.
You can playback by pressing I instead of pressing ENTER.
3� Press H to stop playback.
/
/
/
to select the desired chapter, then press ENTER
●
Download from Www.Somanuals.com. All Manuals Search And Download.
E-20
Video/Picture/Music Playback (continued)
Sorting the titles
Each time you press B (Green) while the Title Name screen is
displayed, the Title Name display changes between displaying the
newest title first and the oldest title first.
Playback by selecting a Playlist
ꢀ� Press C (Yellow) while theTitle List screen is displayed.
●
The Playlist screen is displayed.
Example:Thumbnail screen
Program 1
21/5 Fri 9:30 AM 110 Min.
2� Press H to stop playback.
Operation procedure for the “Functions” menu
ꢀ� Press D (Blue) (Functions) when the CD screen is displayed.
Program
1
Program
2
Program
3
●
The “Functions” menu is activated.
Program
4
Playback from the beginning
EXIT
Select
Title Name
Enter
By Chapter
Return
Original
Exit
Functions
ꢀ� Load an audio CD.
A
B
C
D
●
The CD screen is displayed.
2� Press
/
/
/
to select the desired title, then press ENTER to
(The CD screen is displayed only when a compact disc recorded
in the CD-DA format is inserted.)
start playback.
3� Press H to stop playback.
●
Playback may begin automatically, depending on the disc.
Playback from the beginning or resume playback
When you play back the title from the Title List after you stopped
playback, you can select playback from the beginning or from the
point where it was last stopped.
2� Press
/
to select the desired setting, then press ENTER.
●
●
When playback is stopped, only “Track” can be selected.
For a description of each setting, see “Functions which can be
ꢀ� Press D (Blue) when the desired title is selected while theTitle List
screen is displayed.
2� Press
/
to select the type of Playback, then press ENTER to
3� Press
/
/
/
to set, then press ENTER.
start playback.
●
Operations vary depending on the setting. Follow the operation
●
The type of Playback may be selected from “From Beginning”
or “From Continued”.
instructions on the screen.
4� Press nRETURN/DEMO or D (Blue) to exit the “Functions”
3� Press H to stop playback.
menu.
Note:
2� Press I if playback does not begin automatically or playback is
stopped.
■ Audio CD Playback
● The displayed items vary depending on the disc.
3� To pause the playback at any time, press F.
AUDIO CD
●
Press F or I to return to playback.
■ Audio Data (MP3 File) Playback
4� Press H to stop playback.
5� To return to the HOME screen, press H again, and then press
HOME or EXIT.
This Unit can play back audio CDs.
● For a description of other playback functions, refer to “Playback
CD-R
CD-RW
DVD-R DVD-RW
USB
This Unit can play back audio data (MP3 files) recorded on CD-R/
RW discs, DVD-R/RW discs and USB memory devices or via a home
network.
● For details on the audio data that you can play using this unit, refer
Playback by selecting a track
ꢀ� Press
or when playback is stopped.
Playback of the selected track will begin.
/
to select the track, then press ENTER during playback
●
● When data in the USB memory device is played back, playback
from the USB memory device will stop when OPEN/CLOSE on
the remote control or the unit is pressed or when a disc is inserted
into the unit.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-2ꢀ
Video/Picture/Music Playback (continued)
Disc type display name.
Buttons
Description
HOME SCREEN
Pause audio file playback.
● Return to playback when paused.
F
Video
BD-Video
USB
Music
Skip backward.
Skip forward.
T
U
H
Picture
e-Contents
Home Network
Stop playback.
Settings
Select
Notes:
ENTER
EXIT
Enter
Return
Exit
● The Fast Forward/Reverse function does not work.
● The Repeat function does not work.
3� Press
/
/
to select “Music”, then press or ENTER.
to select “DVD”, “CD”, “USB” or “Home Network”,
● The Random (Shuffle) function does not work.
4� Press
then press or ENTER
.
■ Displaying Still Images (JPEG files)
5� Press
/
to select a folder or file.
●
When you select a folder, press ENTER to open it, and then
CD-R
CD-RW
DVD-R DVD-RW
USB
press
/
to select a file in the folder.
This Unit can display still images (JPEG files) recorded on CD-R/RW
discs, DVD-R/RW discs and USB memory devices or via a home
network.
● For details on the still images that you can display using this unit,
Folder 1
CD
1 Folder 1
2 Folder 2
3 Folder 3
4 Folder 4
5 Track 01.mp3
6 Track 02.mp3
● Still images are played one by one while during “Slide show”, they
are automatically replaced one after another.
● When data in the USB memory device is played back, playback
from the USB memory device will stop when OPEN/CLOSE on
the remote control or the unit is pressed or when a disc is inserted
into the unit.
ꢀ� PressDISCbuttonontheremotecontrolorSELECTORbuttonrepeatedly
1/All 14 files and folders
on the main unit to select DISC function.
2� Load a disc or a USB memory device containing audio data (MP3
*
6� Press ENTER to play back the selected file.
files).
*
●
Playback of the selected file will begin.
When you insert or remove a USB memory device, be sure to
turn the main power off and make sure that “Quick Start” is set
Rear
USB1 terminal
●
When MP3 files are played, the “Functions” menu is not
available.
USB memory device
7� To return to the HOME screen, press
H
(press twice if during
Note:
playback), and then press HOME or EXIT.
● A USB memory device can be used only on USB1 terminal.
List of available buttons during playback
Buttons
Description
Select a desired audio file.
Play back audio file.
/
ENTER
Download from Www.Somanuals.com. All Manuals Search And Download.
E-22
Video/Picture/Music Playback (continued)
ꢀ� Press DISC button on the remote control or SELECTOR button
repeatedly on the main unit to select DISC function.
2� Load a disc or a USB memory device* containing Still Images
(JPEG files).
● When a PC running DLNA server software or other DLNA-
compatible devices are connected to this unit, some setting
changes of software or other devices may be required.
● Please refer to the operating instructions for the software or
devices for more information.
1/77
*
When you insert or remove a USB memory device, be sure to
turn the main power off and make sure that “Quick Start” is set
Note:
● A USB memory device can be used only on USB1 terminal.
Disc type display name.
HOME SCREEN
7� To return to the HOME screen, press H, and then press HOME
or EXIT.
Video
BD-Video
USB
Operational buttons during still image display
Music
Buttons
T/U
Description
Picture
e-Contents
Settings
Home Network
Go to the previous/next picture in the
same directory.
Return to the selection screen.
nRETURN/DEMO
Select
ENTER
EXIT
Enter
Return
Exit
Types of playable files
C (Yellow)
Rotate the picture by 90 degrees to the
left.
3� Press
/
/
to select “Picture”, then press or ENTER.
Video
Music
Picture
DivX Plus HD (avi/divx/mkv)
mp3
jpg
4� Press
to select “DVD”, “CD” or “USB” or “Home Network”,
D (Blue)
Rotate the picture by 90 degrees to the
right.
then press or ENTER.
5� Press
/
to select a folder or file.
Play back Slide Show.
Return to slide show playback when
paused.
I
●
When you select a folder, press ENTER to open it, and then
Notes:
press
/
to select a file in the folder.
● Even if DLNA compatible, a connection may not be able to be
made depending on the server, or playback may not be available
even if a connection is made successfully.
Pause slide show playback.
F
H
Folder 1
Stop still image display/slide show
playback.
● Some files may not be playable depending on the file. For details,
CD
● To enjoy this function, make a broadband Internet connection to
the operation manual disc), then perform the following operation.
● To use this function, we recommend setting “Auto Power Off” to
1 Folder 1
2 Folder 2
3 Folder 3
4 Folder 4
5 Image 01.jpg
6 Image 02.jpg
A (Red)
Notes:
Guide display on/off
● Thumbnail data will be displayed when JPEG files from a digital
camera contain thumbnail data.
● An icon will be displayed for JPEG files which do not contain
1/All 14 files and folders
● Before using this function, please read “Network Service
thumbnail data.
●
To set slide show speed/repeat playback, press D (Blue) (Slide
Playback by selecting a file list
■ Accessing DLNA servers
Show Menu).
ꢀ� Press DISC button on the remote control or SELECTOR button
The unit can browse and play movies, music and photos stored on
your DLNA Certified media servers connected within your home
network.
Slide Show Menu
repeatedly on the main unit to select DISC function.
2� Press
ENTER.
3� Press
/
to select Video/Music/Picture, then press
or
Slide Show Speed
Repeat Mode Setting Setting of slide show repeat playback
Guide Display Setting Guide display setting during still image
Setting of slide show playback speed
About a home network
/
to select “Home Network” in the sub window.
This unit can display and play movies, photos and music content
from your DLNA-compatible digital media servers (such as a PC and
consumer electronics).
display
6� Press ENTER to display the selected file.
Before accessing DLNA servers:
●
The selected still image appears on the screen.
● DLNA servers and this unit must be connected to the same local
area network. Specify the settings required for connecting this unit
to the local area network.
● DLNA servers must be turned on.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-23
Note:
Video/Picture/Music Playback (continued)
Playback Functions
● Subtitles are not played back with BD/DVD video discs during Fast
Forward and Fast Reverse.
Video
BD-Video
USB
■ Skipping to the Next or the Start of the Current
Chapter (Track/Title)
Music
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
DVD-R DVD-RW
CD-R CD-RW
BD-RE
Picture
e-Contents
Settings
Home Network
USB
The Skip (to the beginning of a chapter, track or title) function is
enabled when T or U is pressed during playback.
Sub Window
4� Press ENTER or .
■ Pause/Frame Advance Playback
● The unit automatically scans and displays DLNA servers within
your local network.
BD VIDEO
BD-R
BD-RE
DVD VIDEO
DVD-R DVD-RW
Select server
The Pause function is enabled when F is pressed during playback.
(If you are playing back an audio CD, audio data [MP3 files] or still
images [JPEG files], these will also pause.)
1. xxxxxxxxxxxxx
2. yyyyyyyyyyyyy
3. zzzzzzzzzzzzzz
4. aaaaaaaaaaaa
The Frame Advance Playback function is enabled when U is
pressed during pause.
● Frame Advance Playback may not function properly with discs
other than DVD-RW/R (VR format).
5� Press
/
to select a DLNA server which you want to access,
Notes:
then press ENTER or .
● Some BD/DVD Video discs are not compatible with Pause/Frame
Advance Playback.
● The folder list or file list of the DLNA server which you accessed
is displayed.
● Frame Advance/Reverse Playback can be performed for DVD
discs by pressing U or T during pause.
● Frame Reverse Playback cannot be performed for DivX video.
● The previous screen appears when nRETURN/DEMO is
pressed.
6� Press
/
to select the folder or file which you want to access,
then press ENTER.
● When you select a folder, the file list of the folder is displayed.
■ Slow Playback (Forward/Reverse)
Press
/
to select the file which you want to play, then press
ENTER.
BD VIDEO
BD-R
BD-RE
● Playback starts.
Note:
DVD VIDEO
DVD-R DVD-RW
●
Some operations in the following playback functions cannot be
performed depending on the specifications of the disc.
Root
The Slow Playback (Forward/Reverse) function is enabled when U
or T is pressed for more than 2 seconds during pause.
Press I to return to normal playback.
■ Fast Forward/Reverse (Search)
Folder1
Folder2
Video01.divx
Video02.divx
Video03.divx
Video04.divx
Notes:
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
BD-RE
● This doesn’t work for audio CDs.
● You cannot perform Slow Playback between titles. At the end of
the title, Slow Playback will be cancelled and normal playback will
automatically resume.
DVD-R DVD-RW
● Reverse Slow Playback cannot be performed for BD video and
The Fast Forward/Reverse function is enabled when T or U is
pressed for more than 2 seconds during playback.
● The speed change each time the button is pressed and hold.
DVD discs in AVCHD format.
7� Press to stop playback.
● Reverse Slow Playback cannot be performed for DivX video.
When playing back a DVD
● The file list reappears.
● You cannot perform Fast Forward/Fast Reverse from one title and
continue to another title (except when playing audio CDs). At the
end or beginning of the title, Fast Forward/Fast Reverse will be
cancelled and normal playback will automatically resume.
● The previous screen appears when nRETURN/DEMO is
pressed.
8� Press EXIT or HOME to exit playback.
● The HOME screen reappears.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-24
Playback Functions (continued)
2� Press
/
to select “Scene Selection”, then press ENTER.
■ Repeat Playback of aTitle or Chapter (Repeat
■ Switching Subtitles
●
“Set Start Point” displays.
Playback)
Playback Title
Playback Chapter
Scene Selection
BD VIDEO DVD VIDEO
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
BD-RE
If subtitles are provided in multiple languages, you can switch
between them.
DVD-R DVD-RW
Set Start Point
Press SUBTITLE during playback.
ꢀ� Play back the title or chapter you want to repeat.
3� Press ENTER at the scene where you want to set the start point.
“Set End Point” displays.
● The display indicates the subtitle number currently being played
back, and the subtitles appear.
Each time SUBTITLE is pressed, the subtitles change.
● “–” is displayed if a disc has no subtitles.
● You can also select “Off”.
2� Press PLAY MODE, then press
/
to select the type of Repeat
●
Playback.
4� Press ENTER at the scene where you want to set the end point.
●
You can press U to fast forward to the scene where you
want to set the end point. When you reach the desired scene,
simply press I and then ENTER to set the end point.To cancel
Repeat Playback, press PLAY MODE.
●
●
●
PlaybackTitle: Repeats the title currently being played back.
Playback Chapter: Repeats the chapter currently being played back.
Scene Selection: Repeats the specified scene of title or chapter.
Notes:
● Settings for subtitles can also be changed in the Function Control
Notes:
Playback Title
Playback Chapter
Scene Selection
● Press U, the Repeat Playback is cancelled and the next chapter
being play back.
● The operation of subtitles differs according to each disc.You may
need to refer to the operation manual of the disc.
● The display for subtitle information automatically disappears after
5 seconds.
● Press T once, the Repeat Playback is cancelled and the unit
returns to the start of current chapter (track).
●
If you press T again (within about 5 seconds) the unit will skip to
Notes:
the beginning of the previous chapter (track).
● Press nRETURN/DEMO to cancel without setting the type of
● For Partial Repeat Playback, set the start and end points within
the same title.
■ Switching the Angle
Repeat Playback.
●
For Audio CD, you can select “Playing Disc”, “Playing Track” and
“SpecifyThe Part” as Repeat Playback options.
● Repeat Playback may be forbidden depending on the disc.
● Partial Repeat Playback may not work in multi-angle scenes.
● If you press DISPLAY <DIM>, you can confirm the Repeat
Playback status.
BD VIDEO DVD VIDEO
● Repeat Playback cannot be performed for DivX video.
4� Press ENTER.
If multiple angles are recorded, you can switch between them.
ꢀ� Press FUNCTION <SETUP> during playback.
Example: Repeat playback of a title (TITLE)
●
The Function Control screen is displayed on theTV.
■ Displaying the Audio Information
2� Press
/
to select the Angle Number column, then press
BD-VIDEO
ENTER.
You can display the audio information on the disc currently being
played back by pressing AUDIO.
1/3
BD-VIDEO
The displayed contents vary depending on the disc.
5/25
00:20:30
2 English
1
1 DTS
On Title Repeat
1/3
BD VIDEO DVD VIDEO
5/25
00:20:30
2 English
1
The audio channel currently being played back will be displayed
.
If multiple audio channels are recorded, you can switch the audio
channel by pressing AUDIO.
1 DTS
Off
DVD-RW DVD-R
When a recorded broadcast with stereo or monaural audio is
played back:
3� Press
/
to select the desired Angle Number, then press ENTER.
On Title Repeat
4� Press nRETURN/DEMO or FUNCTION <SETUP> to close the
“Stereo” is displayed. (Audio cannot be switched.)
Function Control screen.
Notes:
Notes:
5� Press PLAY MODE to return to normal playback.
● When you play a programme recorded in stereo or monaural, and if
you are listening to the Bitstream sound via the digital output jack,
you cannot select the audio channel. Set “Audio Out” to “PCM”
● The displayed items vary depending on the disc.
● If you access the Function Control screen during playback of a
BD/DVD video, it may be impossible to operate the BD/DVD video
playback. In cases like this, close the Function Control screen.
● The operation of angles differs according to each disc. You may
need to refer to the operation manual of the disc.
● The display for angle information automatically disappears after
5 seconds.
Note:
●
“Scene Selection” operation is not available for BD video.
■ Partial Repeat Playback (Repeat Playback of a
● Settings for audio can also be changed in the Function Control
● The operation of audio differs according to each disc. You may
need to refer to the operation manual of the disc.
● The display for audio information automatically disappears after
5 seconds.
Specified Part)
DVD VIDEO
DVD-R DVD-RW
AUDIO CD
ꢀ� Press PLAY MODE during playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-25
3 Operation guide display
Functions which can be set
Playback Functions (continued)
Provides help on remote control button operations.
Title/Track Number (DirectTitle/Track Skip)
Function control operation procedure
■ Displaying the Angle Mark
● Shows the title number being played back (or track number when
playing back an audio CD).You can skip to the start of the title (or
track).
BD VIDEO DVD VIDEO
● To skip to the start of a selected title (or track), press the Number
buttons to enter the title (or track) number when this option is
highlighted.
You can change settings so that Angle Mark appears in the right
bottom part of the screen when multiple angles are recorded. The
settings can be changed in “Settings” – “Playback Setting” – “Angle
Chapter Number (Direct Chapter Skip)
● Shows the chapter number being played back.You can skip to the
start of the chapter.
Settings During Playback
● To skip to the start of a selected chapter, press the Number buttons
to enter the chapter number when this option is highlighted.
■ Function Control
Playback ElapsedTime (DirectTime Skip)
BD VIDEO
DVD VIDEO
AUDIO CD
BD-R
BD-RE
● Shows the time elapsed from the beginning of the current disc title
DVD-R DVD-RW
(or track). This lets you skip to a specific time.
● Press
/
to select the Hour, Minute or Second, then press
/
ꢀ� Press FUNCTION <SETUP> during playback.
or the Number buttons to set the time. Press ENTER to start
●
The Function Control screen is displayed on theTV.
This allows you to adjust various settings at once, like subtitles, angle
settings and the title selection for Direct Playback.You can adjust the
video and audio to suit your preferences.The operations are the same
for BD and DVD.
playback at the set time.
2� Press
/
to select the desired setting, then press ENTER.
Subtitle Language
●
For a description of each setting, see “Functions which can be
set” (on this page).
● Shows the currently selected subtitle language. If subtitles are
provided in other languages, you can switch to your preferred
language.
Function Control screen
BD-VIDEO
BD-VIDEO
1/3
1
Angle Number
5/25
00:20:30
2 English
1
1 DTS
Off
1/3
5/25
00:20:30
2 English
● Shows the currently selected angle number. If the video is recorded
with multiple angles, you can switch the angle.
2
1
Audio
1 DTS
Off
● Shows the currently selected type of audio. You can select the
desired type of audio.
ENTER
Select
Exit
Enter
Return
3� Press
/
/
/
to set, then press ENTER.
Repeat
EXIT
●
Operations vary depending on the setting. Follow the operation
3
instructions on the screen.
● The currentTitle (or Chapter) or partial segments can be repeatedly
played back. Repeat Playback is also possible with the PLAY
MODE button on the remote control.
4� Press nRETURN/DEMO or FUNCTION <SETUP> to close the
1 Playback status display
Function Control screen.
Shows the operation status and the disc type.
2 Setting items
Notes:
Note:
● If “– –” is displayed for an option like title number or subtitles, the
disc has no titles or subtitles which can be selected.
● The displayed items vary depending on the disc.
● If you access the Function Control screen during playback of a
BD/DVD video, it may be impossible to operate the BD/DVD video
playback. In cases like this, close the Function Control screen.
Selects a title (or track) or chapter for playback, or performs video/
audio settings.
● These functions may not work with all discs.
● Title/Track Number (DirectTitle/Track Skip)
● Chapter Number (Direct Chapter Skip)
● Playback ElapsedTime (DirectTime Skip)
● Subtitle Language
● Angle Number
● Audio
● Repeat
Download from Www.Somanuals.com. All Manuals Search And Download.
E-26
Settings During Playback (continued)
Settings
■ Setting the PIN code for the first time
ꢀ� Press
2� Press
3� Press
4� Press
/
/
/
/
to select “Settings”, then press or ENTER.
■ Common operations
to select “Playback Setting”, then press or ENTER.
to select “PIN Code Setting”, then press or ENTER.
to select “Yes” to enter the PIN code setting menu.
The “menu” enables various audio/visual settings and adjustments
on the functions using the remote control unit.You need to call up the
On Screen Display to perform settings for this unit. The following is
the explanation for the basic operations of the “menu”.
5� Enter a 4-digit number for the PIN code setting.
6� Press ENTER to complete the PIN code setting.
Example: Setting “AQUOS LINK”
■ Parental Control Setting
PIN code must be set first before setting the Parental Control.
ꢀ� Press
2� Press
3� Press
/
/
/
to select “Settings”, then press or ENTER.
to select “Playback Setting”, then press or ENTER.
to select “Parental Control”, then press or ENTER.
4� Enter your 4-digit PIN code.
● You cannot move to the next setting screen until you input the
correct PIN code.
5� Press
/
to select the parental control level for DVD VIDEO, BD-
ROM, and then select the country code.
Press ENTER after making each selection.
Parental Control
Disc Language
Set parental control level for DVD-VIDEO.
Angle Mark Display
Off
PIN Code Setting
BD Internet Access
Set parental control level for BD-ROM.
3D Mode
No Limit
Canada
3D Notice
Set the country code.
ꢀ� Home screen display
Return
HOME
Audio Video Settings
Smart Settings
Video
6� Press HOME or EXIT to exit.
■ Audio Video Settings
HDMI Video Out
AQUOS LINK
Playback Setting
On Screen Language
Communication Setup
Version
USB Memory Management
Music
Picture
e-Contents
Software Update Settings
Settings
System
This sets the resolution of the video output for the HDMI terminal of
this unit.
Select
ENTER
EXIT
Enter
Return
Exit
Normally set to “Auto” (factory preset value).
Press
/
to select “Settings”, then press or ENTER.
Item
2� Select a menu item
Auto, 1080p, 1080i, 720p, 576/480p
Note:
HOME
Video
● When the BD unit is connected to a 1080p 24Hz compatible
TV and the “HDMI Video Out” is set to “Auto”, 1080p 24Hz will
automatically be displayed when compatible discs are played
back.
Audio Video Settings
Smart Settings
AQUOS LINK
Music
Playback Setting
On Screen Language
Communication Setup
Version
USB Memory Management
Software Update Settings
System
Picture
e-Contents
Settings
Select
ENTER
EXIT
Enter
Return
Exit
Press
/
to select “AQUOS LINK”, then press or ENTER.
3� Select the next item
Press to select the desired item, then press ENTER.
/
Press nRETURN/DEMO to return to the previous “menu” page.
4� Exit the menu screen
Press HOME or EXIT to exit.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-27
Settings (continued)
Secondary Audio
Disc Language (Disc Priority Language)
This lets you select the language for subtitles, audio and menus
displayed on the screen.
Item (Subtitle)
Select the subtitle language you want to display.
Item (Audio)
Select the audio language you want to hear.
Item (Menu)
Select the menu language you want to display.
■ Smart Settings
This toggles the clicking sound on the menu and audio with secondary
video in picture in picture mode for BD-Video.
Quick Start
● Select “Off” when enjoying the high quality sounds of BD-Video.
Item
On, Off
This turns the Quick Start function on and off.
When the Quick Start function is on:
● The startup time of the Unit is reduced.
● However, power consumption will increase.
When the Quick Start function is off:
● The unit will enter the low power consumption mode when in
standby condition.
Audio Out
You can set the audio output when connecting to SURROUND
equipment.
Note:
ꢀ� This sets the audio output connected to SURROUND equipment.
● When “Auto” is selected, the priority language of the disc will be
Item
Yes, No
Note:
Item
played back.
Angle Mark Display
HDMI Output: Select this when you connect using HDMI OUT
terminal.
This lets you turn the Angle Mark Display on or off when BD/DVD
video recorded with multiple angles is played back. (The Angle Mark
is displayed in the lower right screen.)
● When “Quick Start” is set to “Yes”, the Unit requires some time to
2� You can set the audio output mode.
turn off.
Control Panel
This sets the audio output mode for HDMI OUT terminal when
selecting “HDMI Output”.
Item
Yes, No
This lets you set display of the control panel on the TV screen to on
or off.
Note:
● When the secondary audio is set to “On”, PCM is automatically
PIN Code Setting
This sets the PIN code for setting or changing the Parental Control Level.
Item
Yes, No
selected as the audio output mode.
Item
Bitstream:
Item
Yes: Enter the 4-digit number.
No
■ AQUOS LINK
● Select this when connecting to HDMI equipment with a built-in
This lets you set the Unit to receive the control signal from the AQUOS
LINK remote control via the HDMI cable.
Item
Yes, No
decoder for DOLBY DIGITAL, etc.
Notes:
● Setting to Bitstream will output each audio signal by Bitstream.
PCM (Surround):
● When you forget the PIN code, you can reset the current PIN code
● You can also set the new PIN code if desired.
● Select this when connecting to multi-channel HDMI equipment.
● Setting to PCM (Surround) will output by LINEAR PCM by decoding
audio signals recorded in each audio output mode such as DOLBY
DIGITAL, DTS.
Note:
BD Internet Access
● For details, refer to the operation manual ofTV.
This allows you to set access restriction to BD-LIVE contents.
Item
■ Playback Setting
Note:
Permit: Allows all BD-LIVE discs.
Limit: Allows only discs with owner certification.
Prohibit: Prohibits all BD-LIVE discs.
Parental Control
This lets you set the Parental Control depending on the disc content.
The available Parental Control Levels are shown below.
The 4-digit PIN code number needs to be entered before the Parental
Control Levels and the Country Code are set. The Parental Control
Levels and the Country Code cannot be set if a PIN code has not
been created or the PIN code is not entered.
Dynamic Range Control
Notes:
This lets you adjust the range between the loudest and softest sounds
(dynamic range) for playback at average volume. Use this when it is
hard to hear dialogue.
● The available functions differ depending on the disc.
● Regarding playback method of BD-LIVE contents, etc., perform
the operations in accordance with the instructions in the BD disc
manual.
Item
Normal: The same audio output range is played as the original
recorded audio output range.
Shift*: When Dolby Digital audio is played back, the dynamic range of
the audio is adjusted so that the dialogue portion can be heard easily.
(If the audio sounds abnormal, set to “Normal”.)
Auto: When you play back audio in the Dolby TrueHD format, the
dynamic range is automatically adjusted.
● Select the rating level appropriate for the age of the user.
● To enjoy BD-LIVE functions, perform the broadband Internet
Item (Parental control level for DVD-video)
8 and Off: All DVD-video can be played.
1–7: Prohibits play of DVD-video with corresponding ratings recorded
on them.
Item (Parental control level for BD-video)
No Limit: All BD-video can be played.
0–99 year(s): Prohibits play of BD-video with corresponding ratings
recorded on them.
3D Mode
This sets output of 3D images.
To view 3D images, playback of 3D content (3D BD video) is necessary
with a 3D compatibleTV and 3D glasses in addition to this unit.
Item
*
Lower the audio volume before setting. If you do not do so, the speakers may
emit a loud sound or excessive output may be applied to the speakers.
Auto:Video signals are output as 3D when 3D content (3D BD video)
is played or as 2D when 2D content is played.
2D: Even if 3D content (3D BD video) is played, video signals are
output as 2D at all times.
SUPER PICTURE
This enhances the quality of video streaming images with pixel by
pixel processing technology.
Item
On, Off
Item (Country code)
Select the country code.
The ratings differ according to the country.
Note:
details.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-28
Settings (continued)
Caution:
Regarding each of the setup values, confirm the specifications
of your broadband router.
● When viewing 3D images, viewing for a long period of time or lying
on your back may cause eye strain and discomfort. In addition, 3D
images may affect the eyesight of young children/infants, so keep
them from viewing the images.
6�Select “Next”, then press ENTER.
● If selecting “Yes” in the step 5, go to the step 8.
7�Enter your DNS address.
3D Notice
This sets whether or not a notice is displayed (“Yes” or “No”) on the
connectedTV every time 3D content (3D BD video) is played.
Enter your DNS address.
Item
Yes, No
Primary
Secondary
■ On Screen Language
You can set the language you want to display on the screen.
Next
Item
English, Deutsch, Français, Italiano, Español, Português, Nederlands,
Svenska, Dansk, Norsk, Suomi, Polski, Česky, Magyar, Slovensky,
Slovenščina
● The primary and secondary DNS addresses are entered using
■ Version
Regarding each of the setup values, confirm the specifications
of your broadband router.
ꢀ�Press
/
to select “Settings”, then press or ENTER.
When you select “Version”, the system software version is
displayed.
8�Select “Next”, then press ENTER.
2�Press
/
to select “Communication Setup”, then press or
ENTER.
9�For testing the connection to the Internet, after confirming the
settings, press
/
to select “Test”, then press ENTER.
3�Press
/
/
to select “Ethernet Setup”, then press or ENTER.
to select “Change”, then press ENTER.
■ System
4�Press
● “Test” is available only when setting to obtain the IP address
automatically. “Test” cannot be selected if the IP address has
not been obtained automatically.
System Reset
You can reset all settings to the factory presets.
Setting the info. of the Ethernet
[Current Setup]
IP Address : Auto Setup
Netmask : Auto Setup
Item
Reset, Not Reset
Confirm the current setting.
DivX(R) Registration
The DivX registration code is displayed.
Gateway
DNS
: Auto Setup
: Auto Setup
IP Address : xxx xxx xxx xxx
Item
Netmask
Gateway
: xxx xxx xxx xxx
: xxx xxx xxx xxx
Yes, No
Note:
DNS Address : xxx xxx xxx xxx
xxx xxx xxx xxx
MAC Address : xx xx xx xx xx xx
Change
Initialize
DivX(R) Deregistration
You can deactivate your DivX information on the unit.
Test
Item
●
For initializing the current setting, select “Initialize”, then press ENTER.
Complete
Yes, No
5�For setting the IP address, press
/
to select “Yes” or “No”, then
Note:
press ENTER.
● As a result of the test, if the Internet connection fails, enter the
setup values manually.
Do you obtain the IP address
automatically?
■ Communication Setup
ꢀ0�Press
/
to select “Complete”, then press ENTER.
ꢀꢀ�Press HOME or EXIT to return to the HOME screen.
This allows you to perform and/or change the communication
settings and the Internet connection. This setting is required to use
BD-LIVE functions, video on-demand services (e-Contents), home
networks and software updates that connect to the Internet.
Yes
No
● To perform other settings, press nRETURN/DEMO.
IP Address
Netmask
Gateway
Notes:
● Make sure that the LAN cable is connected to this unit.
● For manually performing the setting, the following information
of the connected router or modem is required. Confirm the
information prior to the setting.
Next
● If selecting “Yes”:The IP address is automatically obtained.
–
IP address, netmask, gateway, DNS address
● If selecting “No”: The IP address, netmask and gateway are
manually entered using the screen for inputting characters.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-29
Settings (continued)
The operation procedure for inputting characters manually
2�Press
/
to select the desired input mode.
5�Press D (Blue) (Complete) to fix the numbers which have been
input.
3�Press
/
to select a number/character, then press ENTER.
Note:
4�Repeat the step 3 to display all of the desired characters/numbers
● Numeric characters such as IP address can be entered on the input
screen either by selecting each of the characters in the “Numeric”
mode or using the Number buttons on the remote control.
in the input field.
IP Address
Netmask
Gateway
123
Example:The screen for inputting numeric characters
123
IP Address
Netmask
Gateway
123
Numeric
Edit
6�Repeat step 1 to 5 to finish inputting all the required characters.
1
2
3
4
5
6
7
8
9
0
Notes:
ꢀ�Press ENTER at the boxes in which characters are to be entered,
● Press nRETURN/DEMO (Del.Char.) to delete a number/
and the input screen will appear.
character you have input.
●
To change a number/character you have input, press B (Green)
(Left) or C (Yellow) (Right) to select the number/character you want
to change, and press nRETURN/DEMO (Del.Char.).Then, press
/ to select a new number/character you want to input, and press
ENTER.
Numeric
Edit
1
2
3
4
5
6
7
8
9
0
Selected by pressing
/
Selected by pressing
/
Input character list
Numeric
1 2 3 4 5 6 7 8 9 0
Edit
Cancel
Left
Right
Complete
Del.Char.
The same operation as the coloured buttons and nRETURN/DEMO can be performed by
selecting each of the items and pressing ENTER.
“Del.Char.” stands for deleting characters.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-30
Settings (continued)
Before using the USB memory device
Caution:
● Do not remove the USB memory device or unplug the AC power
lead while the operations for “USB Memory Management” or
“Software Update Settings (Manual Update from USB memory
device)” are being performed.
Note:
8� Press ENTER.
● A USB memory device can be used only with USB1 terminal.
9� Press HOME or EXIT to exit.
Rear
Note:
Data which has been saved to the unit’s internal memory (game
score, etc.) will also be deleted.
● Do not use a USB extension cable when connecting a USB
■ Software Update Settings
memory device to the USB1 terminal.
USB1 terminal
In this unit, the software version can be updated using either one of
the following methods.
–
Using a USB extension cable may prevent the unit from
performing correctly.
Auto Update from Network
Manual Update from Network
Manual Update from USB memory device
●
●
●
Notes:
● SHARP cannot guarantee that all brands’ USB memory devices
will operate with this unit.
USB memory device
Auto Update from Network
● Only USB memory devices formatted with FAT 32/16 are
This function allows you to perform the update by accessing an
Internet connection automatically to check if there is a new firmware
version every time the unit is turned on.
2� Press ON/STAND-BY to turn on the power.
compatible.
3� Press
/
/
to select “Settings”, then press or ENTER.
to select “USB Memory Management”, then press
When formatting a USB memory device using a PC, perform the
following settings.
Format File System: FAT32
4� Press
When using this function, it is required to perform the following
settings in advance.
Notes:
or ENTER.
●
The “USB Memory Management” screen is displayed.
“No USB Memory” appears when no USB memory is
inserted.
Allocation Unit Size: Default Allocation Size
●
Make sure that the LAN cable is connected to this unit.
Make sure to perform the communication settings. (See pages 29
–30.)
●
■ USB Memory Management
●
5� Press
/
to select “Erase” or “Format”, then press ENTER.
The following instructions explain how to delete data such as the
Virtual Package data and the BD-LIVE data in a USB memory
device.
Erase: Deletes only BD-VIDEO data written on the USB memory
It may take time to access and download the update depending
on the Internet connection and other factors.
●
device such as BD-LIVE data.
Format: Be aware that all data including BD-VIDEO data and
software update data will be deleted.
Caution:
Do not remove the LAN cable or unplug the AC power lead while
●
●
If you want to delete only the unneeded software update data
after the software is updated, delete the data on the USB
memory device using a PC.
downloading or updating software.
Erase
Erases BD-VIDEO data on USB memory.
Format
Erase all contents on USB memory
including protected contents.
6� Press
/
to select “Yes”, then press ENTER.
●
A confirmation message is displayed. Check that the correct
USB memory device is displayed, and then continue.
7� Start the process.
The screen for the current operation will display.
Setup
●
Press
/
/
to select “Settings”, then press or ENTER.
to select “Software Update Settings”, then press
ꢀ�
2�
Press
or ENTER.
Complete
OK
Press
ENTER.
Press
/
to select “Auto Update Setting”, then press or
3�
4�
When you insert or remove a USB memory device, be sure to turn
the main power off and make sure that “Quick Start” is set to “No”
ꢀ� Insert the USB memory device into the USB terminal on this unit.
/
to select “Yes”, then press ENTER.
After this, an Internet connection will be made automatically
every time this unit is turned on.
●
Download from Www.Somanuals.com. All Manuals Search And Download.
E-3ꢀ
Settings (continued)
Update process
Caution:
When this unit is turned on, the Internet connection starts
Do not remove the LAN cable or unplug the AC power lead while
●
ꢀ�
Downloading latest firmware…
Version : yyyyyyyyyy
automatically.
downloading or updating software.
“Accessing...” blinks on the screen.
●
30%
The current version of this unit software and the latest version
of the update file on the network are displayed when latest
version of firmware has been found.
To update this unit software with update file, select “Yes”, and
go to step 2.
●
7� When the software is successfully updated, a screen is displayed
indicating that the update process is completed.
If the update has failed, an error message appears.
Retry the update after checking if the broadband Internet
●
Latest version of firmware has been found.
Firmware update is available.
Proceed with update?
Press ON/STAND-BY to turn off the unit.
8�
Manual Update from USB memory device
This function allows software updates by inserting a USB memory
device with the update file into the USB1 terminal on this unit.
Current Version :
Latest Version :
xxxxxxxxxx
yyyyyyyyyy
If “Yes” will be selected, version update will start.
When a software update is performed, the software update data
must be written onto the USB memory device in advance using a
PC.
●
Yes
No
Press
Press
/
/
to select “Settings”, then press or ENTER.
to select “Software Update Settings”, then press
ꢀ�
2�
The USB memory device must be clear of all files except software
●
or ENTER.
update data to allow new software uploading.
If the latest firmware version has been already updated,
nothing is displayed on the screen.
Press ENTER to start updating.
●
Press
Press
/
/
to select “Manual Update”, then press or ENTER.
to select “Network”, then press ENTER.
3�
4�
5�
When software update data is released, copy the data onto a
USB memory device after downloading it to a PC.
●
2�
During access to the network and checking the latest version of
firmware, “Accessing” blinks.
For methods such as downloading and copying to a USB memory
device, carefully read the description shown on the website
before performing the operation.
●
The current version of this unit software and the latest version
of the update file on the network are displayed when latest
version of firmware has been found.
●
Downloading latest firmware…
Version : yyyyyyyyyy
Notes:
To update this unit software with update file, select “Yes”, and
go to step 6.
Only USB memory devices formatted with FAT 32/16 are
●
30%
compatible.
When formatting a USB memory device using a PC, perform the
Latest version of firmware has been found.
Firmware update is available.
Proceed with update?
When the software is successfully updated, a screen is displayed
indicating that the update process is completed.
3�
4�
following settings.
Format File System: FAT32
●
If the update has failed, an error message appears.
Retry the update after checking if the broadband Internet
Allocation Unit Size: Default Allocation Size
Do not extract the firmware update file to any folders other than
the root directory on the USB memory device. The firmware
update file must be only one file directly in the root directory.
Current Version :
Latest Version :
xxxxxxxxxx
yyyyyyyyyy
●
If “Yes” will be selected, version update will start.
Yes
No
Press ON/STAND-BY to turn off the unit before using again.
Manual Update from Network
This function allows you to perform the update operation by
accessing an Internet connection manually to check if there is a new
firmware version.
If the Internet connection has failed, an error message appears.
●
Retry the update after checking if the broadband Internet
Notes:
● Make sure that the LAN cable is connected to this unit.
Make sure to perform the communication settings. (See pages 29
–30.)
●
6� Press ENTER to start updating.
It may take time to access and download the update depending
on the Internet connection and other factors.
●
Download from Www.Somanuals.com. All Manuals Search And Download.
E-32
Settings (continued)
Enter the 4-digit number using 0–9.
7�
8�
Software update file is not detected in the USB memory device.
Confirm that you have transferred the file
to the USB memory device and retry software update.
Confirm that you have inserted the USB memory device
into the correct device.
Enter 4-digit PIN code
OK
Press ENTER to start checking data in the USB memory device.
There is more than one software file
in the USB memory device.
Confirm that only the software update file is
in the USB memory device.
Insert USB memory device containing
the software update file.
OK
OK
Press ENTER to start updating.
ꢀ0�
During the data checking, “Checking” blinks.
9�
The screen becomes dark for a while until the update screen can
be displayed. Please wait for the update screen to appear. Do
not unplug the AC power lead.
●
Now checking the data in USB memory device.
Checking
The picture will temporarily go dark until
the software update display appears.
Wait several minutes and do not unplug the AC cord.
Caution:
Do not remove the USB memory device or unplug the AC power
lead while the software is being updated.
●
The current version of this unit software and the version of
the update file on the USB memory device are displayed. To
update this unit software with update file, select “Yes”, and
press ENTER.
●
When you insert or remove a USB memory device, be sure to turn
the main power off and make sure that “Quick Start” is set to “No”
OK
Insert the USB memory device with the update file into the USB1
ꢀ�
terminal on this unit.
Software update file is detected in the USB memory device.
Start update?
Note:
Now updating
A USB memory device can be used only with USB1 terminal.
●
Do not unplug AC cord.
Update Version
*
Rear
Current Ver. :
Update Ver. :
xxxxxxxxxx
yyyyyyyyyy
yyyyyyyyyy
30%
Yes
No
When the software is successfully updated, a screen is displayed
indicating that the update process is completed.
ꢀꢀ�
If the USB memory device is not properly installed or the correct
update file cannot be found on the USB memory device, an
error message is displayed.
Check the file on the USB memory device, and then reinsert
the USB memory device correctly.
●
If the update has failed, check the file in the USB device and
try Software Update again.
●
Press ON/STAND-BY to turn off the unit.
ꢀ2�
ꢀ3�
USB memory device
Delete unneeded software update data using a PC after the
software update process is completed.
●
Press ON/STAND-BY to turn on the power.
2�
3�
4�
Press
Press
/
/
to select “Settings”, then press or ENTER.
to select “Software Update Settings”, then press
Remove the USB memory device.
or ENTER.
Press
Press
/
/
to select “Manual Update”, then press or ENTER.
to select “USB Memory”, then press ENTER.
5�
6�
If you have set the PIN code, go to step 7, otherwise go to
●
step 8.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-33
Settings (continued)
About Output of Audio Formats
When “Secondary Audio” is set to “On”, the audio is output as 48 kHz.
When “Secondary Audio” is set to “On”, the audio is output as PCM.
When 5.1ch (192kHz), the audio output is downsampled to 96kHz.
When 2ch, the audio is output as 192kHz.
I
J
K
K
Audio format
Maximum number of channels
HDMI
PCM
Bitstream
DolbyTrueHD
7.1ch (48kHz/96kHz)
5.1ch (192kHz)
7.1ch (48kHz)
7.1ch (48kHz/96kHz)
5.1ch (192kHz)
7.1ch (48kHz/96kHz)
7.1ch (48kHz/96kHz)
5.1ch (192kHz)
7.1ch *1
5.1ch *1
7.1ch
7.1ch *1
5.1ch *1/*3
7.1ch *1
7.1ch *1
5.1ch *1
7.1ch *2
5.1ch *2
7.1ch *2
7.1ch *2
5.1ch *2
7.1ch *2
—
Dolby Digital PLUS
DTS-HD Master Audio
DTS-HD High Resolution Audio
LPCM
—
Playing back
Playing back video on demand streaming content
In this unit, you can enjoy a variety of video on demand streaming
content by connecting to the Internet.
Listening to the iPod, iPhone or iPad
Press
Press
/
/
to select “e-Contents”, then press or ENTER.
to select “YouTube”, then press or ENTER.
ꢀ�
2�
3�
4�
5�
iPod
TheYouTube screen is displayed.
Follow the instruction on the screen.
To exit the screen, press EXIT.
Made for:
VOD content
● iPod touch (4th generation)
● iPod touch (3rd generation)
● iPod touch (2nd generation)
● iPod touch (1st generation)
● iPod classic
Operational buttons for playback control
Video
Item
Music
● iPod nano (6th generation)
● iPod nano (5th generation)
● iPod nano (4th generation)
● iPod nano (3rd generation)
● iPod nano (2nd generation)
● iPhone 4
Pause the video content. To resume playing paused
content, press on the playback controls.
Picture
e-Contents
Settings
Skip to the previous video content on the video list.
Skip to the next video content on the video list.
● iPhone 3GS
● iPhone 3G
Play back all the video content on the video list
repeatedly.
VOD content
YouTube
● iPhone
● iPad 2
● iPad
Playing backYouTube video content streaming
●
Switch the video quality to high resolution.
Caution:
Notes:
Please update your iPod, iPhone and iPad unit to the latest software
version before using it. Please visit Apple’s homepage to download
the latest version for your iPod, iPhone and iPad.
Toggle the playback screen between normal and full
screen.
To enjoy this function, make a broadband Internet connection to both
●
To use this function, we recommend setting “Auto Power Off” to
Before using this function, please read “Network Service
Determine the point where you want to play back a
Notes:
Progress bar
●
●
video content by pressing
/
on the progress bar.
● Charging terminal for iPod, iPhone and iPad:
Notes:
Condition
DOCK
USB 2
To turn the playback controls on during full screen display, press
POP-UP MENU.
To return to the main page screen, press TOP MENU/TITLE LIST.
●
USB-2 (iPod) function
YES
YES
(without iPod or
iPhone docking)
●
■ Playing backYouTube content
Other function
YES
YES
YES
(iPod/DISC/Tuner/Audio
In/Line In/Digital In/TV ARC)
(without iPod or
iPhone docking)
This unit can play backYouTube video content streaming through the
Internet.
Stand-by
NO
For more information about YouTube, see the YouTube website
using a PC (http://www.youtube.com).
●
●
The message “This accessory is not made to work with iPhone” or
similar, may appear on the iPhone screen when:
- battery is low.
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
You may also experience brief audio interference during incoming calls.
Notes:
Some video content may not be played back with this unit.
●
The actual functions which can be operated may differ from the
descriptions shown.
●
It may take time to access and download the update depending
on the Internet connection and other factors.
●
Download from Www.Somanuals.com. All Manuals Search And Download.
E-34
Listening to the iPod, iPhone or iPad (continued)
3� Connect iPod, iPhone or iPad to the unit. USB - 2 (iPod) will appear.
iPhone
■ iPod, iPhone and iPad connection (USB 2 only)
iPhone (bottom)
Dock connector
ꢀ� Insert the connector to the iPod, iPhone or iPad.
4� Press the
on the main unit or button on the remote control to
iPad
start playback.
Adaptor for iPhone
Dock for iPhone
■ iPhone playback
Connector
● Sound will only switch from iPhone to the main unit after
authentication process is completed in approximately 10 seconds.
● Incoming calls will pause the playback.
● Once the calls are answered, the conversation can only be heard
through the built-in iPhone speaker.Turn on the iPhone speaker or
undock the iPhone to start conversation.
2� Place the iPad to the stand for iPad.
Connector for iPhone
iPad
Caution:
■ iPod and iPhone connection (Dock only)
Unplug all accessories from the iPod or iPhone before inserting it into
the dock.
Note:
●
Docking station is not recommended for iPad connection.
■ To remove adaptor for iPod or iPhone
Stand for iPad
Adaptor for iPod and iPhone connection
Notes:
● Please use the adaptor supplied with your iPod or iPhone unit.
● You can use an audio cable to connect your iPod to the AUDIO IN
socket if:
Insert the tip of a screwdriver (“–” type,
small) into the adaptor hole as shown and
lift upward to remove.
3� Connect the iPod, iPhone or iPad to the unit via USB connector.
USB 2
1. your iPod adaptor does not fit into the iPod dock on the main unit.
2. you have an iPod that does not have an iPod adaptor.
3. you have an iPod that does not have an iPod 30 pin connector.
■ iPod or iPhone playback (Dock only)
ꢀ� Press the ON/STAND-BY button to turn the power on.
2� Press the iPod <TV OUT> button repeatedly on the remote control
or SELECTOR button repeatedly on the main unit to select iPod
function.
Adaptor No.
iPhone Description
iPhone
iPhone 3G
iPhone 3GS
iPhone 4
Capacity
4GB & 8GB & 16GB
8GB & 16GB
12
15
15
19
16GB & 32GB
16GB & 32GB
3� Insert iPod or iPhone unit into the dock of main unit. “iPod” will
appear.
Caution:
4� Press the (iPod or iPhone ) button to start playback.
● At USB-2 (iPod) mode, once the iPod or iPhone is docked onto
the unit, the iPod or iPhone will automatically start charging. ‘iPod
Dock Charge Mode’ will be displayed. In order to use USB-2 (iPod)
function, the iPod or iPhone must be removed from the docking
station.
■ To insert adaptor for iPod or iPhone
Open the docking station for iPod and iPhone by pulling up.
●
This product is made for iPod, iPhone and iPad.To prevent random
interferencewheniPod,iPhoneoriPadisconnected,theheadphone
output is disabled, and “HP INVALID” will be displayed.
You may also experience brief audio interference during
incoming calls.
● USB 2 terminal does not supportVIDEO out.
iPod, iPhone and iPad can be used on USB 2 terminal.
●
Insert the adaptor for iPod or iPhone into unit and connect your iPod
or iPhone.
■ iPod, iPhone or iPad playback (USB 2)
ꢀ� Press the ON/STAND-BY button to turn the power on.
2� Press the iPod <TV OUT> button repeatedly on the remote control
or SELECTOR button repeatedly on the main unit to select USB-2
(iPod) function.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-35
Listening to the iPod, iPhone or iPad (continued)
Listening to the radio
■ To disconnect iPod, iPhone or iPad
■ Various iPod, iPhone and iPad functions
Simply remove the iPod or iPhone from the docking station or iPad
connector from USB 2 terminal. It is safe to do so even during
playback.
Function
Main unit
Remote
control
Dock/USB 2
Operation
Dock/
USB 2
■ Watching videos on aTV connected to iPod or
Play
Press in the pause mode.
iPhone
ꢀ� Press and hold iPod <TV OUT> button for more than 2 seconds
until “TV OUT ON” appear on display.
2� Press the ENTER button to start playback.
Pause
Stop
Press in the playback mode.
Notes:
Press to stop playback
● If theTV Out setting is already turned on at video menu, the video
is automatically displayed on the TV screen when ENTER key is
pressed.
● TV out display is not support through USB terminal. (iPad)
● To return to watching video on iPod or iPhone screen, press the
MENU button to enter video menu. Then press and hold iPod
<TV OUT> button for more than 2 seconds until “TV OUT OFF”
appears.
● During iPod or iPhone video playback, press and hold iPod <TV
OUT> button will not toggle video out display between iPod and
TV.
Track up/
down
Press in the playback or
pause mode.
If you press the button in
the pause mode, press
the / button to start the
desired track.
Fast
Press and hold down in the
playback mode.
Release the button to
resume playback.
forward/
reverse
Caution:
● Unplug all accessories for the iPod or iPhone before inserting it
into the docking station.
Display
Toggle
____
Press for more than 2
seconds to toggle the video
out display between iPod
orTV.
Press to toggle repeat
mode.
iPod <TV OUT>
■ Tuning
■ Navigating the iPod, iPhone or iPad menus
ꢀ� Press the ON/STAND-BY button to turn the power on.
2� Press theTUNER button repeatedly to select FM Stereo or FM Mono.
3� Press theTUNING ( or ) button on the remote control to tune in
to the desired station.
ꢀ� Press theTOP MENU/TITLE LIST button to view the menu on iPod,
iPhone or iPad unit. Press it again to go back to previous menu.
2� Use the PRESET ( or ) button to select an item on the menu and
then press ENTER button.
Repeat
Shuffle
Menu
____
____
____
Press and hold to toggle
shuffle mode.
●
Manual tuning:
Note:
Press the TUNING ( or ) button repeatedly to tune in to the
desired station.
When navigating the iPod, iPhone or iPad menu with remote control,
do not operate any of the buttons on the iPod or iPhone unit. The
volume level is adjusted by pressing the VOL (+ or –) button on the
remote control or VOLUME (+ or –) knob on the main unit. Adjusting
the volume on the iPod, iPhone or iPad units give no effect.
Press to view the iPod menu
during iPod function.
●
Auto tuning:
When theTUNING ( or ) button is pressed for more than 0.5
seconds, scanning will start automatically and the tuner will
stop at the first receivable broadcast station.
Enter
____
____
Press to confirm the
selection.
iPod, iPhone and iPad operations:
The operations described below depend on the generation iPod,
iPhone and iPad you are using.
System on operation:
When the main unit is powered on, the iPod, iPhone or iPad units will
automatically power on when docked or connected in the unit.
Notes:
Cursor
Press to select the iPod
menu.
● When radio interference occurs, auto scan tuning may stop
automatically at that point.
Up/Down
● Auto scan tuning will skip weak signal stations.
● To stop the auto tuning, press theTUNING ( or ) button again.
● When an RDS (Radio Data System) station is tuned in, the
frequency will be displayed first, and then the RDS indicator will
light up. Finally, the station name will appear.
● Full auto tuning can be achieved for RDS stations “ASPM”, see
System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked iPod,
iPhone or connected iPad unit will automatically turn to stand-by
mode.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-36
Listening to the radio (continued)
■ To erase entire preset memory
■ Information provided by RDS
Each time the DISPLAY <DIM> button is pressed, the display will
switch as follows:
ꢀ� Press the ON/STAND-BY button to enter the stand-by mode.
To receive an FM stereo transmission:
2� Whilst pressing down the
button, press the ON/STAND-BY
● Press theTUNER button to select stereo mode and “ST” indicator
will be displayed. “ ” and “ ” will appear when an FM broadcast
is in stereo.
button until “Tuner Clear” appears.
ON/STAND-BY
● If the FM reception is weak, press theTUNER button to extinguish
the “ST” indicator. The reception changes to monaural, and the
sound becomes clearer.
Using the Radio Data System (RDS)
■ Memorising a station
RDS is a broadcasting service which a growing number of FM
stations provide.These FM stations send additional signals along
with their regular programme signals. They send their station
names, and information about the type of programme such as
sport, music, etc.
You can store 40 FM stations in memory and recall them at the push
of a button. (Preset tuning)
ꢀ� Perform steps 1 - 3 in “Tuning”.
2� Press the ENTER button.
When tuned to an RDS station, “RDS” and the station name will be
displayed.
“TP” (Traffic Programme) will appear on the display when the received
broadcast carries traffic information, and “TA” (Traffic Announcement)
will appear whilst a traffic information is on air.
“PTYI” (Dynamic PTY Indicator) will appear whilst the Dynamic PTY
station is received.
3� Within 30 seconds, press the PRESET ( or ) button to select
the preset channel number. Store the stations in memory, in order,
starting with preset channel 1.
4� Within 30 seconds, press the ENTER button to store that station in
memory. If the “ENTER” and preset number indicators disappear
before the station is memorised, repeat the operation from step
2.
5� Repeat steps 1 - 4 to set other stations, or to change a preset
station. When a new station is stored in the memory, the station
previously memorised for that preset channel number will be
erased.
You can control the RDS by using the buttons on the remote
control only.
Note:
The backup function protects the memorised stations for a few
hours should there be a power failure or the AC power lead become
disconnected.
Station name (PS)
Frequency
Programme type (PTY)
Radio text (RT)
■ To recall a memorised station
ꢀ� Press the PRESET ( or ) button to select the desired station.
■ To scan the preset stations
The stations saved in the memory can be scanned automatically.
(Preset memory scan)
ꢀ� Press the PRESET ( or ) button for more than 0.5 seconds.
The preset number will flash and the programmed stations will be
tuned in sequentially, for 5 seconds each.
When tuning in to a station other than an RDS station or to an RDS
station which sends weak signal, the display will change in the
following order:
No PS
No PTY
No RT
2� Press the PRESET ( or ) button again when the desired station
is located.
FM 98.80 MHz
Download from Www.Somanuals.com. All Manuals Search And Download.
E-37
Using the Radio Data System (RDS) (continued)
● “No PS”, “No PTY” or “No RT” will flash for about 5 seconds, and
(This does not mean that you can listen to the traffic information at
that time.)
■ Using the Auto Station Programme Memory
then the frequency will be displayed.
(ASPM)
When the traffic information is broadcast, “TA” will appear.
Descriptions of the PTY (Programme Type) codes, TP (Traffic
Programme) andTA (Traffic Announcement)
Notes: for radio text:
Whilst in the ASPM operation mode, the tuner will automatically search for
new RDS stations. Up to 40 stations can be stored.
If you have already stored some stations in memory, the number of
new stations you can store will be less.
ꢀ� Press the TUNER button on the remote control or SELECTOR
button repeatedly on the main unit to selectTUNER function.
2� Press and hold down the RDS ASPM button on the remote control.
1 After “ASPM” has flashed for about 4 seconds, scanning will
start (87.50 - 108.00 MHz).
● The first 14 characters of the radio text will appear for 4 seconds
and then they will scroll across the display.
● If you tune in to an RDS station which is not broadcasting any
radio text, “No RT” will be displayed when you switch to the radio
text position.
You can search for and receive the following PTY, TP andTA signals.
NEWS
Short accounts of facts, events and publicly
expressed views, reportage and actuality.
● Whilst radio text data is received or when the text contents change,
AFFAIRS
Topical programme expanding or enlarging upon
the news, generally in different presentation style or
concept, including debate, or analysis.
“RT” will be displayed.
■ To recall stations in memory
INFO
Programmes whose purpose is to impart advice in
the widest sense.
To specify programmed types and select stations (PTY search):
You can search a station by specifying the programme type (news,
in memory.
SPORT
Programme concerned with any aspect of sport.
2
When an RDS station is found, “RDS” will appear for a short time
and the station will be stored in memory.
EDUCATE
Programme intended primarily to educate, of which
the formal element is fundamental.
ꢀ� Press the TUNER button on the remote control or SELECTOR
button repeatedly on the main unit to selectTUNER function.
2� Press the RDS PTY button on the remote control.
DRAMA
CULTURE
All radio plays and serials.
Programmes concerned with any aspect of national
or regional culture, including language, theatre,
etc.
Programmes about the natural sciences and
technology.
Used for mainly speech-based programmes usually
of light-entertainment nature, not covered by other
categories. Examples include: quizzes, panel
games, personality interviews.
Commercial music, which would generally be
considered to be of current popular appeal, often
featuring in current or recent record sales charts.
3 After scanning, the number of stations stored in memory will
be displayed for 4 seconds, and then “END” will appear for 4
seconds.
SCIENCE
VARIED
“SELECT” and “PTY TI” will appear alternately for about 6
seconds.
3� Within 6 seconds, press the PRESET ( or ) button to select the
To stop the ASPM operation before it is complete:
programme type.
Press the RDS ASPM button whilst it is scanning for stations.
The stations which are already stored in memory will be kept there.
POP M
Notes:
● If the same station is broadcasting on different frequencies, the
strongest frequency will be stored in memory.
● Any station which has the same frequency as the one stored in
memory will not be stored.
Each time the button is pressed, the programme type will appear. If
the button is held down for more than 0.5 seconds, the programme
type will appear continuously.
ROCK M
EASY M
Contemporary modern music, usually written and
performed by young musicians.
● If 40 stations have already been stored in memory, the scan will be
aborted. If you want to redo the ASPM operation, erase the preset
memory.
Current contemporary music considered to be
“easy-listening”, as opposed to Pop, Rock or
Classical, or one of the specialised music styles,
Jazz, Folk or Country. Music in this category is
often but not always, vocal, and usually of short
duration.
Classical music for general, rather than specialist
appreciation. Examples of music in this category
are instrumental music, and vocal or choral works.
Performances of major orchestral works,
symphonies, chamber music, etc., and including
Grand Opera.
Musical styles not fitting into any of the other
categories. Particularly used for specialist music of
which Rhythm & Blues and Reggae are examples.
4� Whilst the selected programme type is flashing (within 6 seconds),
press the RDS PTY button again.
● If no station have been stored in memory, “END” will appear for
about 4 seconds.
● If the RDS signals are very weak, station names may not be stored
in memory.
After the selected programme type has been lit for 2 seconds,
“SEARCH” will appear, and the search operation will start.
Notes:
LIGHT M
●
The same station name can be stored in different channels.
● In a certain area or during certain time periods, the station names
may temporarily be different.
● If the display has stopped flashing, start again from step 2. If the
unit finds a desired programme type, the corresponding channel
number will lit for about 8 seconds, and then the station name will
remain it.
● If you want to listen to the same programme type of another
station, press the RDS PTY button whilst the channel number or
station name is flashing. The unit will look for the next station.
● If no station can be found, “NOT FOUND” will appear for 4
seconds.
CLASSICS
OTHER M
■ Notes: for RDS operation
If any of the following events occur, it does not mean that the
unit is faulty:
● “PS”, “No PS” and a station name appear alternately, and the unit
does not operate properly.
● If a particular station is not broadcasting properly or a station
is conducting tests, the RDS reception function may not work
properly.
WEATHER
FINANCE
Weather reports and forecasts and meteorological
information.
Stock Market reports, commerce, trading, etc.
If you select the traffic programme:
If you select the traffic programme (TP) in step 3, “TP” will appear.
●
When you receive an RDS station whose signal is too weak, information
like the station name may not be displayed.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-38
Using the Radio Data System (RDS) (continued) Timer and sleep operation (Remote control only)
1 minute or more
CHILDREN
SOCIAL
For programmes targeted at a young audience,
primarily for entertainment and interest, rather than
where the objective is to educate.
Programmes about people and things that influence
them individually or in groups. Includes: sociology,
history, geography, psychology and society.
Daily timer
Once timer
Stop
Stop
Start
Start
RELIGION
PHONE IN
TRAVEL
Any aspect of beliefs and faiths, involving a God or
Gods, the nature of existence and ethics.
Involving members of the public expressing their
views either by phone or at a public forum.
Features and programmes concerned with travel
to near and far destinations, package tours and
travel ideas and opportunities. Not for use for
announcements about problems, delays, or
roadworks affecting immediate travel where TP/TA
should be used.
Programmes concerned with recreational activities
in which the listener might participate. Examples
include, Gardening, Fishing, Antique collecting,
Cooking, Food & Wine, etc.
Polyphonic, syncopated music characterised by
improvisation.
Songs which originate from, or continue the
musical tradition of the American Southern States.
Characterised by a straightforward melody and
narrative story line.
Current Popular Music of the Nation or Region in
that country’s language, as opposed to International
“Pop” which is usually US or UK inspired and in
English.
Music from the so-called “golden age” of popular
music.
■ Timer playback
Before setting timer:
If it is not set, you cannot use the timer function.
● For timer playback: Plug in USB or load discs or dock iPod to
be played.
ꢀ� Press the ON/STAND-BY button to turn the power on.
LEISURE
2� Press and hold the CLOCK/TIMER button.
3� Within 10 seconds, press the
or
button to select “Once” or
button to select “Timer
“Daily”, and press the ENTER button.
4� Within 10 seconds, press the or
Set”, and press the ENTER button.
JAZZ
5� To select the timer playback source (DISC,TUNER, USB-2 (iPod),
COUNTRY
iPod, DIGITAL IN, AUDIO IN, LINE IN,TV ARC), press the
button. Press the ENTER button.
or
When you select the tuner, select a station by pressing the
or button, and then press the ENTER button. If a station has
not been programmed, “No Preset” will be displayed and timer
setting will be cancelled.
NATION M
6� To adjust the day, press the
or
button and then press the
ENTER button.
OLDIES
FOLK M
7� Press the ENTER button to adjust the hour. Press the
or
button and then press the ENTER button.
Music which has its roots in the musical culture
of a particular nation, usually played on acoustic
instruments. The narrative or story may be based
on historical events or people.
8� To adjust the minutes, press the
or
button and then press
the ENTER button.
9� Set the time to finish as in steps 7 and 8 above.
ꢀ0�Adjust the volume using theVOLUME control, and then press the
ENTER button. Do not turn the volume up too high.
ꢀꢀ�Press the ON/STAND-BY button to enter the power stand-by
mode. The “TIMER” indicator lights up and the unit is ready for
timer playback.
Timer playback:
The unit turns on and plays the desired source (DISC, TUNER, USB-2
(iPod), AUDIO IN, LINE IN, DIGITAL IN) at a preset time.
DOCUMENT Programme concerned with factual matters,
presented in an investigative style.
Broadcast when testing emergency broadcast
equipment or receivers.
Emergency announcement made under exceptional
circumstances to give warning of events causing
danger of a general nature.
Broadcasts which carry traffic announcements.
Traffic announcements are being broadcast.
This unit has 2 types of timer: ONCETIMER and DAILYTIMER.
TEST
Once timer:
Once timer play works for one time only at a preset time.
ALARM!
(“ ” indicator).
Daily timer:
Daily timer play works at the same preset time every day that we set.
For example, set the timer as a wake-up call every morning.
(“DAILY” indicator).
TP
TA
Using the once timer and daily timer in combination:
For example, use the once timer to listen a radio programme, and use
the daily timer to wake up.
ꢀ2�When the preset time is reached, playback will start. The volume
will increase gradually until it reaches the preset volume.The timer
indicator will blink during timer playback.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-39
Timer and sleep operation (Remote control only) (continued)
Enhancing your system
ꢀ3�When the timer end time is reached, the system will enter the
The connection lead is not included. Purchase a commercially
available lead as shown below.
■ Sleep operation
power stand-by mode automatically.
Once timer:
The radio, disc, iPod, USB, Audio In, Line In, TV (ARC) and Digital In
can all be turned off automatically.
The timer will be cancelled.
Daily timer:
The timer operates at the same time every selected day. It will
continue until the daily timer setting is cancelled. Cancel the daily
timer when it is not in use.
ꢀ� Play back the desired sound source.
2� Press the SLEEP button.
3� Within 5 seconds, press the Numeric button to set the time.
(1 minute ~ 99 minutes)
Notes:
4� “SLEEP” will appear.
5� The unit will enter the power stand-by mode automatically after the
preset time has elapsed.The volume will be turned down 1 minute
before the sleep operation finishes.
● When performing timer playback using another unit connected to
the USB 2, AUDIO IN, LINE IN or DIGITAL IN socket select “USB-2
(iPod)” or “AUDIO IN” or “LINE IN” or “DIGITAL IN” in step 5.
● This unit will turn on or enter the power stand-by mode
automatically. However, the connected unit will not turn on or off.
To stop the timer playback, follow step “Cancelling the timer
setting” of this page.
Portable audio
unit, etc.
To confirm the remaining sleep time:
ꢀ� Whilst “SLEEP” is indicated, press the SLEEP button.
To cancel the sleep operation:
Checking the timer setting:
Press the ON/STAND-BY button whilst “SLEEP” is indicated. To
cancel the sleep operation without setting the unit to the stand-by
mode, proceed as follows.
Audio cable (not supplied)
ꢀ� Turn the power on and press and hold down the CLOCK/TIMER
button.
■ Listening to the playback sounds of portable audio
2� Within 10 seconds, press the
or
button to select “Once” or
button to select “Timer
ꢀ� Whilst “SLEEP” is indicated, press the SLEEP button.
2� Within 5 seconds, press the “0” button twice until “SLEEP 00”
appears.
unit, etc.
“Daily”, and press the ENTER button.
3� Within 10 seconds, press the
or
ꢀ� Use a connection lead to connect the portable audio unit etc. to
the AUDIO IN socket. When using video equipment, connect the
audio output to this unit and the video output to a television.
2� Press the ON/STAND-BY button to turn the power on.
3� Press the INPUT button on the remote control or SELECTOR
button repeatedly on main unit to select AUDIO IN function.
4� Play the connected equipment. If volume level of the connected
device is too high, sound distortion may occur. Should this happen,
lower the volume of the connected device. If volume level is too
low, increase the volume of the connected device.
Call”, and press the ENTER button.
Cancelling the timer setting:
■ To use timer and sleep operation together
ꢀ� Turn the power on and press and hold down the CLOCK/TIMER
button.
Sleep and timer playback:
For example, you can fall asleep listening to the radio and wake up to
iPod in the next morning.
2� Within 10 seconds, press the
“Daily”, and press the ENTER button.
or
or
button to select “Once” or
3� Within 10 seconds, press the
button to select “Timer Off”,
ꢀ� Set the sleep time (see above, steps 1 - 5).
2� Whilst the sleep timer is set, set the timer playback (steps 2 - 9,
and press the ENTER button. Timer will be cancelled (the setting
will not be cancelled).
Note:
Reusing the memorised timer setting:
The timer setting will be memorised once it is entered. To reuse the
same setting, perform the following operations.
To prevent noise interference, place the unit away from the
television.
Sleep timer
setting
Timer playback
setting
End
time
■ Headphones
ꢀ� Turn the power on and press and hold down the CLOCK/TIMER
1-99 minutes
Desired time
button.
● Do not turn the volume on to full at switch on and listen to music
at moderate levels. Excessive sound pressure from earphones and
headphones can cause hearing loss.
Sleep operation will
automatically stop
Timer playback
start time
2� Within 10 seconds, press the
or
button to select “Once” or
button to select “Timer On”
“Daily”, and press the ENTER button.
3� Within 10 seconds, press the
or
● Before plugging in or unplugging the headphone, reduce the
, and press the ENTER button.
volume.
4� Press the ON/STAND-BY button to enter the power stand-by
● Be sure your headphone has a 3.5 mm (1/8”) diameter plug
and impedance between 16 and 50 ohms. The recommended
impedance is 32 ohms.
mode.
● Pluggingintheheadphonedisconnectsthespeakersautomatically.
Adjust the volume using theVOLUME control.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-40
Troubleshooting chart
Many potential problems can be resolved by the owner without calling
a service technician.
If something is wrong with this product, check the following before
calling your authorised SHARP dealer or service centre.
■ Power
■ Picture
Problem
Possible causes and solutions
Problem
Possible causes and solutions
No picture.
Make sure that the cable is connected correctly.
●
●
The power cannot be
turned on.
Is the power cord firmly plugged into the AC
●
●
■ Tuner
Make sure that the connectedTV or the AV
Make sure that region code on the disc matches
Symptom
Possible cause and solutions
●
●
■ Basic Operation
●
The radio makes
unusual noises
continuously.
●
●
Is the unit placed near theTV or computer?
Is the FM aerial placed properly? Move the aerial
away from the AC power lead if it is located
nearby.
Problem
Possible causes and solutions
There is no picture from the HDMI output.
●
–
Are the settings performed correctly? Please
The remote control
does not work.
Use the remote control within its operating
●
■ USB
●
●
Screen freezes and
operation buttons do
not work.
Turn off the power and turn on the power again.
If the power is not turned off, perform a reset.
Is the disc damaged or dirty? Check the
●
●
Cannot operate the
Unit.
Are you operating the Unit within the specified
Symptom
Possible cause
●
●
●
Device cannot be
detected.
●
●
●
●
Is there any MP3/WMA file available?
Is the device properly connected?
Is it an MTP device?
■ Playback
Square noise (mosaic)
appears on the
screen.
Blocks in images may be visible in scenes with
rapid movement due to the characteristics of
digital image compression technology.
Does the device contain AAC file only?
Problem
Possible causes and solutions
●
Playback does not
start.
Wrong time
display.
Wrong file name
display.
●
Is it a false MP3 file?
The Unit cannot play
a disc.
Make sure that the disc is loaded properly
Make sure that region code on the disc matches
●
●
Audio is not output, or
images are not played
back properly.
The audio may not be output or the images may
not be played back properly for some discs in
which copyright-protected contents are recorded.
●
●
●
●
●
IsVariable Bitrate file being played back?
Is the File Name written in Chinese or Japanese
characters?
●
●
●
●
●
3D images cannot be
output to aTV.
Is an HDMI cable used?
●
●
●
Allow any condensation in or near the Unit to dry.
Are a 3D compatibleTV and 3D glasses used?
Is a proper connection made between the HDMI
OUT terminal of the unit and the HDMI input
Are all devices (amplifier, AV receiver, etc.)
between theTV and the unit connected by HDMI
■ iPod, iPhone or iPad
Check that the disc is recorded in the compatible
TV system (PAL or NTSC).
The Unit cannot play back video which was not
Symptom
No sound is
produced.
No image appears
on theTV/monitor.
Possible cause and solutions
●
●
●
●
●
The iPod, iPhone or iPad is not playing.
The iPod, iPhone or iPad is not properly
connected to the unit.
Is the AC power lead of the unit plugged in?
The video cable is not properly connected.
TheTV/monitor’s input selection is not properly
set.
The iPodTV out feature has not been set to
output video.
USB terminal do not support video.
Proper playback may be impossible due to
the state of the disc recording, a scratched,
warped or dirty disc, the state of the pick-up, or
compatibility issues between this Unit and the
Is the 3D setting on theTV correct?
Is a 3D compatible BD disc being played back?
●
●
●
●
●
●
When the recorded time of a disc is unusually
short, playback may not be possible.
●
●
Noise appears on the
screen.
When you watchTV broadcasts with the power
of this unit turned on, noise may appear on the
TV screen. In such cases, turn off the power to
this unit or keep this unit away from theTV.
●
●
BD-RE/R discs recorded in a format other than
●
●
The disc is
Make sure that the disc is loaded properly
●
●
●
iPod, iPhone
or iPad will not
charge.
The iPod, iPhone or iPad is not making full
contact with the connector.
automatically ejected
after closing the disc
tray.
●
●
●
●
Using iPod (3rd generation).
The iPod or iPhone is not supported. Refer to
Video stops.
Has the Unit been subjected to shock or impact?
Are you using it in an unstable location?The Unit
will stop if it senses shock or vibration.
●
“This accessory is
not made to work
with iPhone” or
“This accessory is
not supported by
iPhone” appears
on iPhone screen.
●
●
The iPhone battery is low. Please charge the
iPhone.
iPhone is not properly docked.
The Unit makes a
snapping sound when
starting playback or
loading a disc.
The unit may sometimes make a snapping
sound when starting playback if it has not
been operated in a while.These sounds are not
malfunctions of the unit but are normal operating
conditions.
●
Download from Www.Somanuals.com. All Manuals Search And Download.
E-4ꢀ
Troubleshooting chart (continued)
Maintenance
■ Sound
■ Condensation
■ Cleaning the cabinet
Sudden temperature changes, storage or operation in an extremely humid
environment may cause condensation inside the cabinet (BD pickup, etc.) or
on the transmitter on the remote control. Condensation can cause the unit
to malfunction. If this happens, leave the power on with no disc in the unit
until normal playback is possible (about 1 hour). Wipe off any condensation
on the transmitter with a soft cloth before operating the unit.
Periodically wipe the cabinet with a soft cloth and a diluted soap
solution, then with a dry cloth.
Problem
Possible causes and solutions
No sound, or sound is
distorted.
If the volume of theTV or amplifier (XL-BD601PH)
is set to minimum, turn the volume up.
Check that the audio cable is connected
Check that the cable plugs are clean.
Audio may not be output depending on the audio
recording status, such as when audio other than
an audio signal or non-standard audio is recorded
●
●
Caution:
● Do not use chemicals for cleaning (petrol, paint thinner, etc.). It
may damage the cabinet.
● Do not apply oil to the inside of the unit. It may cause
●
●
●
malfunctions.
■ If problem occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal supply voltage
due to lightning, etc.) or if it is operated incorrectly, it may malfunction.
If such a problem occurs, do the following:
Audio is not output,
or images are not
played back properly.
The audio may not be output or the images
may not be played back properly for some
discs in which copyright-protected contents are
recorded.
●
ꢀ� Set the unit to the stand-by mode and turn the power on again.
2� If the unit is not restored in the previous operation, unplug and
plug in the unit again, and then turn the power on.
Note:
■ Network
If neither operation above restores the unit, clear all the memory by
resetting it.
Problem
Possible causes and solutions
■ Factory reset, clearing all memory
Cannot connect to
the Internet.
When the wired Internet connection is made
Is the wrong cable such as a modular cable
used? Connect a LAN cable to the ETHERNET
●
●
ꢀ� Press the ON/STAND-BY button to enter the power stand-by
mode.
2� Whilst pressing down the OPEN/CLOSE button, press the
ON/STAND-BY button until “Clear All” appears.
Is the power for the connected equipment, such
as a broadband router or modem turned on?
Is the broadband router and/or modem properly
connected?
Is the proper value(s) set in the network setting?
●
●
●
Caution:
This operation will erase all data stored in memory including clock,
timer settings and tuner preset.
Cannot download
BD-LIVE contents.
Is the USB memory device properly connected?
Check that the USB memory device is connected
Check if the BD disc supports BD-LIVE.
●
●
■ Before transporting the unit
●
●
Remove the iPod, iPhone, iPad, USB memory device and disc from
the unit. Then, set the unit to the power stand-by mode. Carrying the
unit with iPod, iPhone, iPad or USB memory device left connected or
discs left inside might damage the unit.
■ Other
Problem
Possible causes and solutions
TheTV operates
incorrectly.
SomeTVs with wireless remote control capability
may operate incorrectly when using the remote
control of this Unit. Use suchTVs away from this
Unit.
●
●
The Unit heats up
during use.
When using this Unit, the console cabinet may
heat up depending on the usage environment.
This is not a malfunction.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-42
On-screen Error Messages
The following messages appear on theTV screen in case of an error during operation.
Error message
Possible Error
Suggested Solution
Check the disc, and load it correctly.
Cannot play.
The disc cannot be played back with this Unit.
●
●
●
●
Incompatible disc.
If you load a disc which cannot be played with this Unit (i.e. a scratched
disc), or if you load a disc upside down, this message will appear, and
the disc tray will automatically pop out.
Occurs if the loaded disc cannot be played because it is a non-
standard disc or scratched, etc.
Remove the disc.
●
●
Cannot operate.
Occurs if an operation is incorrect.
This USB memory is not formatted properly. Please format the
memory in USB memory management.
Occurs if there is a formatting error.
Occurs if the USB memory is not formatted with FAT 32/16.
Format the USB memory again.
Format the USB memory with your PC.
●
●
●
●
The Connected USB Memory cannot be used. It should be compliant
with USB 2.0
Occurs if USB memory not compliant with USB 2.0 High Speed
(480Mbit/s) is used (i.e. USB 1.0/USB 1.1).
Connect USB 2.0 High Speed (480Mbit/s) compliant USB memory.
●
●
Specifications
As part of our policy of continuous improvement, SHARP reserves
the right to make design and specification changes for product
improvement without prior notice. The performance specification
figures indicated are nominal values of production units. There may
be some deviations from these values in individual units.
Output terminals
Speakers: 6 ohms
■ USB
20Hz - 20kHz
Subwoofer Pre-out (audio signal):
200 mV/10 k ohms at 70 Hz
Video output: 1Vp-p
USB
● USB 1 (5V dc 500 mA
USB 2.0 High Speed (for Local Storage/
Software Update/JPEG/MP3 and DivX
(H.264/MKV) playback)
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
HDMI 19-pin standard connector (1080p
24Hz output)
■ General
● USB 2 (5V dc 2.1 A)
(iPod/iPhone and iPad compatibility)
Power source
AC 220 - 240V ~ 50/60 Hz
HDMI™ (Deep Colour, x.v.Colour, Dolby
TrueHD, DTS-HD Master Audio | Essential)
Power consumption
Power on: 52 W
Power stand-by: 0.5 W (*)
■ Tuner
Input terminals
Audio In (audio signal):
500 mV/47 k ohms
Dimensions
Width: 215 mm (8 - 1/2”)
Height: 96 mm (3 - 4/5”)
Depth: 335 mm (13 - 1/5”)
Frequency range
Preset
FM: 87.5 - 108 MHz
40 (FM station)
Line in (Analogue input):
500 mV/47 k ohms
Digital audio optical input terminal: Square
Optical terminal
Weight
2.75 kg (6.06 lbs.)
■ Speaker
Operating temperature 5°C to 35°C
Ethernet:
10BASE-T/100BASE-TX
Storage temperature
Operating humidity
TV systems
–20°C to 60°C
10 % to 80 % (no condensation)
PAL system/NTSC system (The system
recorded on the disc is output.)
Type
2-way type speaker system
2.5 cm (1”) Dome-Tweeter
12 cm (4-3/4”) woofer
■ BD player
Maximum input
power
Rated input power 50 W
Impedance
Dimensions
100 W
Type
Signal readout
Single disc multi-play disc unit
Non-contact, 3-beam
semiconductor laser pickup
( * ) Thispowerconsumptionvalueisobtainedwhenthedemonstration
mode is cancelled in the power stand-by mode. Refer to page 10
to cancel the demonstration mode.
6 ohms
Playable discs/
media formats
BD-ROM, BD-RE, BD-R,
DVDVideo, DVD+RW/+R/-RW/-R (Video/
VR/AVCHD/JPEG file/MP3 file/DivX
(H.264/MKV) format),
■ Amplifier
Width: 148 mm (5-13/16”)
Height: 262 mm (10-5/16”)
Depth: 203.5 mm (8”)
Output power
PMPO: 200 W
Audio CD (CD-DA), CD-RW/R (CD-DA/
JPEG file/MP3 file format)
MPO: 100 W (50 W + 50 W)
(10%T.H.D.)
Weight
2.50 kg (5.51 lbs.)/each
Region code
B or marked ALL for BD, 2 or marked ALL
for DVD
Multi bit D/A converter
RMS: 100 W (50 W + 50 W)
(10%T.H.D.)
RMS: 66 W (33 W + 33 W)
(1%T.H.D.)
D/A converter
Frequency response 20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
Download from Www.Somanuals.com. All Manuals Search And Download.
E-43
Glossary
Deep Colour
archive data or for storing and distributing video material.The DVD+/
-R has two different formats: VR format and Video format. DVDs
created in Video format have the same format as a DVD video, while
discs created in VR (Video Recording) format allow the contents to
be programmed or edited.
AVCHD (Advanced Video Codec High Definition) refers to a recording
format (specification) for digital video cameras which can record to a
disc such as 8 cm DVD disc and play back digital high definition images.
Deep Colour can reproduce rich colours, increasing the number of
bits describing colours.
This Unit is compatible with Deep Colour.You can enjoy this function
by connecting to a Deep Colour compatible TV using an HDMI
cable.
This lets you select things like the subtitle language or audio format
using a menu stored on the DVD video disc.
BDAV (Blu-ray Disc Audio/Visual, BD-AV) refers to one of the
application formats used for writable Blu-ray discs such as BD-R,
BD-RE, etc. BDAV is a recording format equivalent to DVD-VR (VR
mode) of the DVD specifications.
A DVD+/-RW is a recordable and rewritable DVD. The re-recordable
feature makes editing possible. The DVD+/-RW has two different
formats: VR format and Video format. DVDs created in Video format
have the same format as a DVD video, while discs created in VR
(Video Recording) format allow the contents to be programmed or
edited.
BD-J application
The BD-ROM format supports Java for interactive functions. “BD-J”
offers content providers almost unlimited functionality when creating
interactive BD-ROM titles.
A sound system developed by Dolby Laboratories Inc. that gives
movie theatre ambience to audio output when the product is
connected to a Dolby Digital processor or amplifier.
HDMI (High-Definition Multimedia Interface) is an interface that
supports both video and audio on a single digital connection. The
HDMI connection carries standard to high definition video signals
and multi-channel audio signals to AV components such as HDMI
equippedTVs, in digital form without degradation.
A variety of interactive content is available from BD-LIVE compatible
Blu-ray discs via the Internet.
A sound system developed as an extension to Dolby Digital. This
audio coding technology supports 7.1 multi-channel surround
sound.
BDMV (Blu-ray Disc Movie, BD-MV) refers to one of the application
formats used for BD-ROM which is one of the Blu-ray Disc
specifications. BDMV is a recording format equivalent to DVD-video
of the DVD specification.
Interlace format
Dolby TrueHD is a lossless coding technology that supports up to 8
channels of multi-channel surround sound for the next generation
optical discs. The reproduced sound is true to the original source
bit-for-bit.
Interlace format shows every other line of an image as a single “field”
and is the standard method for displaying images on television. The
even numbered field shows the even numbered lines of an image,
and the odd numbered field shows the odd numbered lines of an
image.
A BD-R (Blu-ray Disc Recordable) is a recordable, write-once Blu-
ray Disc. Since contents can be recorded and cannot be overwritten,
a BD-R can be used to archive data or for storing and distributing
video material.
This is a digital sound system developed by DTS, Inc. for use in
cinemas.
JPEG (Joint Photographic Experts Group) is a still image data
compression format and is used in most of digital cameras.
DTS-HD High Resolution Audio is a new technology developed for
the next generation high definition optical disc format.
DTS-HD Master Audio is a lossless audio compression technology
developed for the next generation high definition optical disc format.
A BD-RE (Blu-ray Disc Rewritable) is a recordable and rewritable
Blu-ray Disc.
Linear PCM is a signal recording format used for Audio CDs and on
some DVD and Blu-ray discs. The sound on Audio CDs is recorded
at 44.1 kHz with 16 bits. (Sound is recorded between 48 kHz with
16 bits and 96 kHz with 24 bits on DVD video discs and between 48
kHz with 16 bits and 192 kHz with 24 bits on BD video discs.)
BD-ROMs (Blu-ray Disc Read-Only Memory) are commercially
produced discs. Other than conventional movie and video contents,
these discs have enhanced features such as interactive content,
menu operations using pop-up menus, selection of subtitle display,
and slide shows. Although a BD-ROM may contain any form of data,
most BD-ROM discs will contain movies in High Definition format for
playback on Blu-ray Disc units.
DTS-HD Master Audio | Essential
DTS-HD Master Audio | Essential is a lossless audio compression
technology developed for the next generation high definition optical
disc format.
MP3 files are audio data compressed in the MPEG1/2 Audio layer-3
file format. “MP3 files” have “.mp3” as extensions.
MPEG-2
Upscaling (upconverting) refers to a function of various units and
devices that enlarge the image size to fit the size of the screen of
video equipments such as aTV.
MPEG-2 (Moving Picture Experts Group phase 2) is one of the video
data compression schemes, which is adopted for DVD videos and
digital broadcasts worldwide. Some Blu-ray Discs also use high
bitrate MPEG-2.
A disc format developed for recording/playing high-definition (HD)
video (for HDTV, etc.), and for storing large amounts of data. A single
layer Blu-ray Disc holds up to 25 GB, and a dual-layer Blu-ray Disc
holds up to 50 GB of data.
A disc format that contains up to eight hours of moving pictures
on a disc the same diameter as a CD. A single-layer single sided
DVD holds up to 4.7 GB; a double layer single-sided DVD, 8.5 GB;
a single layer double-sided DVD, 9.4 GB; double-layer double-sided
DVD, 17 GB. The MPEG 2 format was adopted for efficient video
data compression. It is a variable rate technology that encodes the
data to according to the status of the video for reproducing high-
quality images. Audio information is recorded in a multi-channel
format such as Dolby Digital, allowing for a realistic audio presence.
This is a feature of DVD and BD video discs. In some discs, the
same scene is shot from different angles, and these are stored
in a single disc so you can enjoy playback from each angle. (This
function can be enjoyed if the disc is recorded with multiple angles.)
Sections of a movie or a music feature that are smaller than titles.
A title is composed of several chapters. Some discs may only be
comprised of a single chapter.
This function allows you to operate this unit using the TV remote
control by displaying the control panel on theTV screen.
This is a feature of DVD and BD video discs. This function makes it
possible to record different audio tracks for the same video, so you
can enhance your enjoyment by switching the audio. (You can enjoy
this function with discs recorded with multiple audio tracks.)
Copy guard
A DVD+/-R is a recordable, write-once DVD. Since contents can
be recorded and cannot be overwritten, a DVD+/-R can be used to
This function prevents copying. You cannot copy discs marked by
the copyright holder with a signal which prevents copying.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-44
Glossary (continued)
In some digital broadcasts and BD/DVD video discs, a control level
for disc viewing is set depending on the age of the viewer. With this
Unit, you can set the control level for viewing such broadcasts and
discs.
If you stop playback while it is in progress, the Unit stores the stop
position in memory, and this function lets you playback from that
point.
In a BD/DVD video, this is the menu for selecting things like the
chapter to be played back and the subtitle language. In some DVD
videos, the top menu may be called the “Title Menu”.
This returns to the start of the chapter (or track) being played, or
skips to the next chapter (or track).
These numbers are assigned to the tracks which are recorded on
audio CDs. They enable specific tracks to be located quickly.
An enhanced menu operation available on BD video discs. The pop-
up menu appears when POP-UP MENU is pressed during playback,
and can be operated while playback is in progress.
x.v.Colour
These are the lines of text appearing at the bottom of the screen
which translate or transcribe the dialogue. They are recorded on
many DVD and BD video discs.
x.v.Colour reproduces a greater range of colour than before, showing
almost all of the colours that the human eye can detect. (Applicable
for JPEG files only with this system)
Progressive format
Compared to the Interlace format that alternately shows every other
line of an image (field) to create one frame, the Progressive format
shows the entire image at once as a single frame. This means that
while the Interlace format can show 30 frames/60 fields in one
second, the Progressive format can show 60 frames in one second.
The overall picture quality increases and still images, text, and
horizontal lines appear sharper.
This indicates the play time which has elapsed from the start of a
disc or a title. It can be used to find a specific scene quickly. (It may
not work with some discs.)
YouTube is a website where users can upload and view video
content, such as video clips andTV clips.You can watch the content
streamed on yourTV.
These numbers are recorded on DVD and Blu-ray discs. When a
disc contains two or more movies, these movies are numbered as
title 1, title 2, etc.
Code identifying a geographic region of compatibility for a BD/DVD.
Network Service Disclaimer
This Sharp device facilitates the access to content and services
provided by third parties. The content and services accessible
via this device belong to and may be proprietary to third parties.
Therefore, any use of such third party content and services must
be in accordance with any authorisation or terms of use provided
by such content or service provider. Sharp shall not be liable to you
or any third party for your failure to abide by such authorisation
or terms of use. Unless otherwise specifically authorised by the
applicable content or service provider, all third party content
and services provided are for personal and non-commercial use;
you may not modify, copy, distribute, transmit, display, perform,
reproduce, upload, publish, license, create derivative works from,
transfer or sell in any manner or medium any content or services
available via this device.
You may not be able to access content or services from the device
for a variety of reasons which may be unrelated to the device itself,
including, but not limited to, power failure, other Internet connection,
or failure to configure your device properly. Sharp, its directors,
officers, employees, agents, contractors and affiliates shall not
be liable to you or any third party with respect to such failures or
maintenance outages, regardless of cause or whether or not it could
have been avoided.
SHARP IS NOT AN AGENT OF AND ASSUMES NO RESPONSIBILITY
FOR THE ACTS OR OMISSIONS OF THIRD PARTY CONTENT OR
SERVICE PROVIDERS, NOR ANY ASPECT OF THE CONTENT OR
SERVICE RELATEDTO SUCHTHIRD PARTY PROVIDERS.
IN NO EVENT WILL SHARP AND/OR ITS AFFILIATES BE LIABLETO
YOU OR ANYTHIRD PARTY FOR ANY DIRECT, INDIRECT, SPECIAL,
INCIDENTAL, PUNITIVE, CONSEQUENTIAL OR OTHER DAMAGES,
WHETHER THE THEORY OF LIABILITY IS BASED ON CONTRACT,
TORT, NEGLIGENCE, BREACH OF WARRANTY, STRICT LIABILITY
OR OTHERWISE AND WHETHER OR NOT SHARP AND/OR ITS
AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
ALL THIRD PARTY CONTENT OR SERVICES ACCESSIBLE VIA
THIS DEVICE IS PROVIDED TO YOU ON AN “AS-IS” AND “AS
AVAILABLE” BASIS AND SHARP AND ITS AFFILIATES MAKE NO
WARRANTY OR REPRESENTATION OF ANY KIND TOYOU, EITHER
EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY
WARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT,
FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTIES
OF SUITABILITY, AVAILABILITY, ACCURACY, COMPLETENESS,
SECURITY, TITLE, USEFULNESS, LACK OF NEGLIGENCE OR
ERROR-FREE OR UNINTERRUPTED OPERATION OR USE OF
THE CONTENT OR SERVICES PROVIDED TO YOU OR THAT THE
CONTENT OR SERVICES WILL MEET YOUR REQUIREMENTS OR
EXPECTATIONS.
Sharp is not responsible, nor liable, for customer service-related
issues related to the third party content or services. Any questions,
comments or service-related inquiries relating to the third party
content or service should be made directly to the applicable content
or service provider.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-45
About Software License
Information on the Software License forThis Product
Software composition
The software included in this product is comprised of various
software components whose individual copyrights are held by
SHARP or by third parties.
Software developed by SHARP and open source software
The copyrights for the software components and various relevant
documents included with this product that were developed or written
by SHARP are owned by SHARP and are protected by the Copyright
Act, international treaties, and other relevant laws. This product also
makes use of freely distributed software and software components
whose copyrights are held by third parties. These include software
components covered by a GNU General Public License (hereafter
GPL), a GNU Lesser General Public License (hereafter LGPL) or
other license agreement.
GPL and LGPL include similar requirements. For information on
obtaining the source code for the open source software and for
obtaining the GPL, LGPL, and other license agreement information,
visit the following website:
Software License Notice
Software License Notice Requirements
The software components incorporated into this product include
components whose copyright holders require license notices. The
license notices for these software components are shown below.
OpenSSL License
This product includes software developed by the OpenSSL Project
for use in the OpenSSLToolkit. (http://www.openssl.org)
Original SSLeay License
This product includes cryptographic software written by Eric Young
We are unable to answer any questions about the source code
for the open source software. The source code for the software
components whose copyrights are held by SHARP is not distributed.
Acknowledgements
The following open source software components are included in this
product:
• cairo • Curl • DirectFB • Droid Sans font • Droid Sans Fallback
font • Fltk • FreeType • Giflib • glib • Icu • Jpeg • Libpng •
LibPThread
• Librt • libsoup • Libstdc++ • libxml2 • OpenSSL • pango • swfdec
• Webkit • zlib • linux kernel • uClibc • modutils • NanoXML
• org.apache.oro.text.regex • libsysfs • mtd/jffs2 • ncurses • libiconv
• libusb • busybox • bash • libmpeg2 • libjpeg • FontConfig
BSD License
This product includes software developed by the University of
California, Berkeley and its contributors.
Obtaining source code
Some of the open source software licensors require the distributor to
provide the source code with the executable software components.
Download from Www.Somanuals.com. All Manuals Search And Download.
E-46
Download from Www.Somanuals.com. All Manuals Search And Download.
|