Sunbeam Bedding Thermostat HE3100 User Manual

Convection Plus Heaters

Instruction Booklet

HE3100 1200W heater with micathermic elements

HE3900 2200W heater with micathermic elements

Please read these instructions carefully

and retain for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sunbeam’s Safety Precautions

Sunbeam are very safety conscious when

• Never leave an appliance unattended while

in use.

designing and manufacturing consumer products,

but it is essential that the product user also

exercise care when using an electrical appliance.

Listed below are precautions which are essential

for the safe use of an electrical appliance:

• Do not use an appliance for any purpose

other than its intended use.

• Do not place an appliance on or near a hot gas

flame, electric element or on a heated oven.

Do not place on top of any other appliance.

• Read carefully and save all the instructions

provided with an appliance.

• Do not let the power cord of an appliance hang

over the edge of a table or bench top or touch

any hot surface.

• Always turn the power off at the power outlet

before you insert or remove a plug. Remove

by grasping the plug – do not pull on the cord.

• For safety reasons and to avoid maintenance

by unskilled persons, some appliances are

‘sealed’ using tamperproof screws. Such

appliances should always be returned to the

nearest Sunbeam Appointed Service Centre

for adjustment or repair if required.

• Turn the power off and remove the plug

when the appliance is not in use and

before cleaning.

• Do not use your appliance with an extension

cord unless this cord has been checked

and tested by a qualified technician or

service person.

• Do not operate any electrical appliance with

a damaged cord or after the appliance has

been damaged in any manner. If damage is

suspected, return the appliance to the nearest

Sunbeam Appointed Service Centre

• Always use your appliance from a power

outlet of the voltage (A.C. only) marked

on the appliance.

for examination, repair or adjustment.

• This appliance is not intended for use by young

children or infirm persons unless they have

been adequately supervised by a responsible

adult to ensure that they can use the appliance

safely.

• For additional protection, Sunbeam

recommend the use of a residual current

device (RCD) with a tripping current not

exceeding 30mA in the electrical circuit

supplying power to your appliances.

• Young children should be supervised to ensure

that they do not play with the appliance.

• Do not immerse the appliance in water

or any other liquid unless recommended.

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sunbeam’s Safety Precautions

• This heater becomes hot during use. To avoid

burns, do not let bare skin touch hot surfaces.

If provided, use handles when moving this

heater. Keep combustible materials such as

furniture, pillows, bedding, papers, clothes and

curtains at least 3 feet (90cm) away from the

front of the heater and keep them away from

the sides and rear.

• Do not insert or allow foreign objects to enter

any ventilation or exhaust openings as this may

cause electric shock or fire, or damage to the

heater.

• To prevent a possible fire, do not block air

intakes or exhaust in any manner. Do not use

on soft surfaces, such as beds, where opening

may become blocked.

• Extreme caution is necessary when any heater

is used by or near children or invalids and

whenever the heater is left unattended.

• A heater has hot and arcing or sparking parts

inside. Do not use it in areas where petrol,

paint or flammable liquids are used or stored.

• Always unplug the heater when not in use.

• Do not use outdoors.

• To prevent overheating, do not cover the

heater.

• Do not run the cord of the heater under

carpeting. Do not cover the cord with throw

rugs, runners or other floor coverings. Arrange

the cord away from traffic areas where it will

not be tripped over.

• When turned on for the first time, your

new heater will emit a slight odour for

up to 8 hours. This is due to the initial

heating of the materials used. It is safe, not

detrimental to the performance of the heater

and will not reoccur. Sunbeam advises that

the heater be placed in a well ventilated

area during this period.

• Do not locate the heater immediately below a

socket outlet.

• Do not use this heater in the immediate

surrounds of a bath, shower, laundry area or

swimming pool.

If you have any concerns regarding the performance and use of your appliance,

please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.

Ensure the above safety precautions are understood.

Download from Www.Somanuals.com. All Manuals Search And Download.

Sunbeam’s Total Safety System

Safety auto shut-off

Instant tip-over cut-out

Your Sunbeam Convection Plus Heater is

equipped with a safety system that detects

any abnormally high temperatures within the

heater and automatically cuts power to the

heating element, preventing overheating.

Once the heater has cooled it will

Your Sunbeam Convection Plus Heater is also

equipped with an instant tip over cut-out

switch. This switch automatically interrupts

the power flow to the heating element when

the heater is tilted to a certain angle. If

the heater is tipped over, it will not turn on

until it has been placed back in the upright

position.

automatically resume normal operation.

Thermal back-up fuse

Note: The tip over cut-out switch will activate

when the heater is tilted forward, backward

or sideways. Care should be taken to ensure

your heater remains upright at all times.

In addition to this automatic shut-off, your

heater contains a thermal back-up fuse to

provide additional back-up protection. If the

heater is in an overheat situation, the back-

up fuse will open, stopping the power flow

to the heating element. This fuse cannot

be reset, so in the event that the back-up

fuse is activated, the heater will need to be

replaced.

Download from Www.Somanuals.com. All Manuals Search And Download.

Features of your HE3100

Convection Plus Heater

Double heat micathermic elements

The revolutionary micathermic heating

elements produce both radiant and

convection heat. Instant heat radiates from

the large surface area in one minute, while

natural convection circulates warm air around

the room quickly and evenly.

Wall mountable

The slim design is ideal for wall mounting.

The unique reflective design keeps the rear of

the heater cooler, enabling it to be mounted

directly onto the wall, without the clearance

required by other panel heaters.

Safety auto shut-off

This built-in safety system detects any

abnormally high temperatures within the

heater and automatically switches it off to

prevent overheating.

Handle and wheels

Wheels and a handle at the rear of

the unit allow you to safely move the

heater while in use.

Instant tip over cut-out

The instant tip over cut-out switch

Figure 1

automatically cuts the power flow to the

heating element if the heater is tipped over.

The heater will not resume operation until it

is replaced in the upright position.

Download from Www.Somanuals.com. All Manuals Search And Download.

Power ON light

Illuminates to indicate that the

heater is switched on.

Mode dial

Turn the mode dial to select your

desired setting: OFF, LOW (1)

or HIGH (2).

Thermostat indicator light

The red thermostat light indicates

that the heater is warming up to the

selected temperature and will go out

when the selected temperature has

been reached.

Thermostat dial

Turn the thermostat dial clockwise to

select your desired temperature.

Adjustable thermostat

The adjustable thermostat allows you

to set the temperature to your desired

comfort level.

Once the selected heat level is

reached, the heater will automatically

cycle on and off to maintain it.

Dimensions

When the wheels are attached, your

HE3100 Convection Plus heater is

approximately:

(L)620 x (W)245 x (H)510mm

Download from Www.Somanuals.com. All Manuals Search And Download.

Features of your HE3900

Convection Plus Heater

Double heat micathermic elements

The revolutionary micathermic heating

elements produce both radiant and

convection heat. Instant heat radiates from

the large surface area in one minute, while

natural convection circulates warm air around

the room quickly and evenly.

Safety auto shut-off

This built-in safety system detects any

abnormally high temperatures within the

heater and automatically switches it off to

prevent overheating.

Instant tip over cut-out

The instant tip over cut-out switch

automatically cuts the power flow to the

heating element if the heater is tipped over.

The heater will not resume operation until it

is replaced in the upright position.

Handle and wheels

Wheels and a handle at the rear of

the unit allow you to safely move the

heater while in use.

Wall mountable

The slim design is ideal for wall mounting.

The unique reflective design keeps the rear of

the heater cooler, enabling it to be mounted

directly onto the wall, without the clearance

Figure 2

required by other panel heaters.

Adjustable thermostat

The adjustable thermostat allows you to set

the temperature to your desired comfort level.

Once the selected heat level is reached, the

heater will automatically cycle on and off to

maintain it.

Download from Www.Somanuals.com. All Manuals Search And Download.

Remote control

The easy to use remote control enables the

heater to be operated from anywhere in the

room.

Figure 3

LED screen

The LED screen displays the current settings

including the ambient room temperature, the

selected mode, or timer setting.

ON/OFF switch

Illuminates to indicate that the heater is

switched on.

Mode button

Press the mode button to select your desired

operating mode: STANDBY, LO, HI or AUTO.

Select the AUTO mode when setting the

digital thermostat.

Timer button

The timer button allows you to program the

heater to automatically switch on or off after

a desired time period. It can be set to turn

on between 1 and 12 hours or off between

0.5 and 8 hours.

Infrared receiver

Point the remote control towards the infrared

receiver to operate the heater from anywhere

in the room.

Plus/minus arrows

Use the plus/minus arrow buttons when

in AUTO mode to select your desired heat

setting or after pressing the timer button to

select your desired time setting.

Dimensions

When the wheels are attached your

HE3900 Convection Plus heater is

approximately:

(L)850 x (W)245 x (H)600mm

Download from Www.Somanuals.com. All Manuals Search And Download.

Using your Convection Plus Heater

HE3100 – 1200W heater with micathermic elements

1.Place the heater on a flat level surface and

ensure that the air intake and outlet are

clear of obstructions.

5.Turn the thermostat dial clockwise until

the red thermostat indicator light turns on,

indicating that the heater is warming to

the selected temperature. This light will go

out when the selected temperature level is

reached.

Note: When turned on for the first time,

your new heater will emit a slight odour

for up to 8 hours. This is due to the initial

heating of the materials used. It is safe,

not detrimental to the performance of

the heater and will not reoccur. Sunbeam

advises that the heater be placed in a well

ventilated area during this period.

6.The thermostat is now set and will

automatically maintain the pre-set

temperature level by turning the heater on

and off.

7.To adjust the selected temperature level,

rotate the thermostat dial anti-clockwise to

lower or clockwise to raise the temperature.

2.Ensure that the mode dial and thermostat

dial are both in the OFF position.

3.Insert the plug into a 230/240V power

outlet and turn the power on. The power

ON light will illuminate.

8.To turn the heater off, move the mode dial

to the OFF position.

4.Move the mode dial to your desired heat

setting, either low heat (1) or high heat

(2).

Download from Www.Somanuals.com. All Manuals Search And Download.

Using your Convection Plus Heater continued

HE3900 – 2200W heater with micathermic elements and remote control

1.Place the heater on a flat level surface and

ensure that the air intake and outlet are

clear of obstructions.

Using the remote control

The remote control allows you to conveniently

operate the heater from anywhere in the room.

(Refer to Note on Page 8).

The buttons on the remote control are

identical to the buttons on the heater. When

using your remote control simply follow the

normal operation instructions outlined on

pages 9 and 10 in addition to the points

below.

2.Ensure that the ON/OFF switch is in the

OFF position.

3.Insert the plug into a 230/240V power

outlet and turn the power on. Move the

ON/OFF switch (located on the side of the

heater) to the ON position. The ON/OFF

switch will then illuminate.

1.Ensure that the remote control contains

2 x AAA batteries.

The LCD screen will display the ambient

room temperature.

2.Point the remote towards the infrared

receiver on the heater (located below the

plus/minus arrows). Ensure that there are

no objects blocking the path between the

remote and the infrared receiver.

Note: When the heater is switched on it will

be automatically set to the standby mode.

4.Press the mode button to select your

desired operating mode. Each time you

press the mode button, it will scroll

through the various settings as follows:

3.Follow steps 1 to 4 on the left column of

this page.

Note: The maximum transmission distance

between the heater and remote is

approximately 30 metres.

the heater remains inactive

STANDBY

when in this mode

Setting the digital thermostat

The digital thermostat allows you to set your

desired temperature for the room. The heater

will then cycle on and off to maintain it.

the heater will continuously run

at approximately 800 watts

1. Follow steps 1 to 3 on the left column of

this page.

the heater will continuously run

at approximately 2200 watts

2.Press the mode button until the AUTO

mode is displayed. Once in AUTO mode,

the LED screen will flash your previous

pre-set temperature for 5 seconds. After

5 seconds the LED screen will display the

ambient room temperature.

for operating the digital

thermostat

AUTO

5.To turn the heater off, move the ON/OFF

switch to the OFF position.

Download from Www.Somanuals.com. All Manuals Search And Download.

Using your Convection Plus Heater continued

3.Use the plus/minus arrows to select your

desired setting. The LED screen will

flash the set value for 5 seconds. After 5

seconds the LED screen will display the

ambient room temperature.

4.Once you have selected your desired timer

setting, the ambient room temperature and

the timer icon

screen.

will display on the LED

Note: When the time has run out, the

timer icon will cease to appear on the

LED screen. The heater will then return to

STANDBY mode.

Note: The temperature range is from 15ºC

to 28ºC. If you scroll past 28ºC the display

will automatically return to 15ºC.

4.The digital thermostat is now set and

will automatically maintain your selected

temperature level by turning the heater on

and off.

Timer auto ON function

The timer auto on function allows you

to program the heater to switch on at a

specified time to preheat the room.

Note: It is normal for the heater to cycle

on and off as it maintains the selected

temperature.

1.Set the heater to the standby mode, by

pressing the mode button.

Note: The LED screen will appear black in

this mode.

5.To turn the heater off, move the ON/OFF

switch to the OFF position.

2.Press the timer button. The LED screen

will display a default time of 0.0hr.

Using the timer

Your HE3900 Convection Plus heater features

a timer function that switches the heater off

after a specified period of time, eg: 3 hours.

It also enables you to preheat the room by

switching the heater on automatically.

3.Use the plus/minus arrows to select the

number of hours you wish the heater to

operate before it automatically switches on,

between 1 and 12 hours.

Note: The timer will automatically set

within 5 seconds of the last time that

either the plus/minus arrows or timer

buttons are pressed.

Timer auto OFF function

1.Set the heater to the desired setting using

the mode button.

2.Press the timer button. The LED screen

will display a default time of 0.0hr.

4.Once you have selected your desired timer

setting, the ambient room temperature and

the timer icon

screen.

will display on the LED

3.Use the plus/minus arrows to select the

number of hours you wish the heater to

operate before it automatically switches

off, between 0.5 and 8 hours.

Note: When the time has run out, the

timer icon will cease to appear on the

LED screen. The heater will then return

to AUTO mode, set to your last pre-set

temperature.

Note: The timer will automatically set

within 5 seconds of the last time that

either the plus/minus arrows or timer

button are pressed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Wall Mounting and Attaching

the Wheels

Wall mounting

1.Before wall mounting your heater, remove

the wheels.

2.Mark the screw location on the wall,

approximately 1 metre from the floor.

Note: The heater must be fixed no lower

than 6.5cm above the floor and no higher

��

than 1.8 metres above the floor. The heater

must also be fixed at least 1 metre from

both the corner and ceiling (refer to figure

4 below).

Figure 5

3.Insert one of the screw anchors into

the hole.

Drill the first hole using a suitable drill bit.

4.Put the mounting support on the wall over

the hole and screw it into place.

��

5.Mark the second screw location,

approximately 138mm from the first hole,

and 1 metre from the floor. Drill the second

hole.

��

6.Insert the second screw anchor into the

hole.

Figure 4

7.Place the mounting support over the second

hole and screw it into place. Tighten both

screws.

Note: Any electrical appliances to be fitted

in a bathroom should be installed by a

qualified electrician in accordance with

Australian/New Zealand Standard Wiring

Rules. Portable heaters should not be used

in a bathroom.

8.Lift the heater and position over the screws.

Attaching the wheels

Fix each wheel support in position with the

screws provided.

Heaters that can be permanently fixed

must be installed so that any controls

cannot be reached by a person using a

bath or shower, as shown in Figure 5.

Download from Www.Somanuals.com. All Manuals Search And Download.

Care and Cleaning

Ensure that the heater is switched off and

disconnected from the power outlet before

cleaning.

Do not use harsh or abrasive cleaners to

clean your heater, as these will damage the

surface.

Carefully wipe the exterior of the heater

with a soft damp cloth and dry thoroughly

with a dry cloth.

If not wall mounted, store the heater in a

cool dry place when not in use.

Over time, dust may accumulate on the

front grille. This can be removed by wiping

with a damp cloth, or by carefully going

across the grille with a vacuum cleaner or

hand held vacuum.

Download from Www.Somanuals.com. All Manuals Search And Download.

‘Sunbeam’, is a registered trademark of Sunbeam

Corporation.

Made in China. Due to minor changes in design or

otherwise, the product may differ from the one shown

in this leaflet. Backed by Sunbeam’s 3 Year Replacement

Guarantee and National Service Network.

ABN 45 000 006 771

Sunbeam Corporation is a division of GUD Holdings Ltd.

For more information or advice on this or any other

Sunbeam appliance, visit www.sunbeam.com.au or

contact the Sunbeam Consumer Service Line.

Australia 1800 025 059

New Zealand 0800 786 232

01/06

Download from Www.Somanuals.com. All Manuals Search And Download.

Consumer Hotline

Australia

1800 025 059

New Zealand

0800 786 232

www.sunbeam.com.au

is a registered Trademark of Sunbeam

Corporation Limited. ABN 45 000 006 771.

Download from Www.Somanuals.com. All Manuals Search And Download.

Shindaiwa Blower 68232 94011 User Manual
Sony Car Stereo System CDC X317 User Manual
Sony Digital Camera CSS TNA User Manual
Sony Headphones WRT 807A User Manual
Sony Video Game Headset SBH70 User Manual
Stanton DJ Equipment VRM 10 User Manual
Star Manufacturing Fryer 510FD User Manual
Star Manufacturing Waffle Iron SWB7R1E User Manual
Star Micronics Printer NX 2420 User Manual
State Industries Water Heater STGPG 0303 User Manual