LCD PROJECTOR LENS
MODEL NO. LNS-W03
LENS REPLACEMENT
AND INSTALLATION PROCEDURES
NOTES ON REPLACEMENT AND INSTALLATION
The procedures and the needed pars for lens installation depend on the type of
cabinet. Before installing or replacing the lens, make sure the type of cabinet and be
sure to refer to the Installations corresponding with your projector.
When installing or replacing the lens, make sure the Lens Model No. matches with
your projector. Refer to the catalog, or contact your sales dealer for the proper Lens
Model No.
TYPE OF THE CABINET AND INSTALLATION PROCEDURES
Refer to the Installation procedure corresponding to your projector and install the lens
correctly. (See the chart below.)
Type of the Cabinet (1) See Page 2
Type of the Cabinet (2) See Page 4
For use the other models (other than above cabinet), contact your sales dealer.
1AA6P1P2952-- (ICYZ)
Download from Www.Somanuals.com. All Manuals Search And Download.
(Type 1 Cabinet)
LENS REPLACEMENT AND INSTALLATION PROCEDURE
1
5
Perform the steps
to
for lens replacement and installation.
UPPER LENS COVER
C
First set the lens at the center position with lens
shift adjustment.
REMOVE THE LENS COVER. (See figure-1)
1
1. Remove screws A (2 screws).
2. Pull down the lower lens cover while pushing
the part D, then remove it.
B
3. Remove screws B (2 screws).
4. Remove screws C (2 screws) and remove
upper lens cover.
D
2
Fig-1
D
● IN CASE OF MODEL WITHOUT LENS
A
LOWER LENS COVER
REMOVE THE COVER PLATE OF THE LENS COVER. (See figure-2)
Remove 2 screws and pull down the plate.
4
(At the step
, insert the light-block sheet in
the same position as the removed cover plate
has been placed. Two screws are not used.)
Disconnect the Lens Shift connector
("K16A") from circuit board. (See Fig. 3.)
SCREWS
Fig-2
COVER PLATE
● IN CASE OF MODEL WITH LENS
❋Figure shown inside of the cabinet.
LENS MOTOR
REMOVE THE LENS. (See figure-3.)
(D)
(D)
1. Disconnect the Lens Shift connector
“K16A” from circuit board.
2. Disconnect the Zoom and Focus con-
nector “K16B” from circuit board.
A
3. Loosen the A, B wire holder and
remove the lens motor lead.
(D)
(D)
4. Remove screws D (4 screws) which
fastens the lens and remove the lens.
B
A
LENS
MOTOR LEAD
Fig-3
CONNECTORS " K16A" and " K16B"
-2-
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALL THE LENS. (See figure-4)
3
LENS MOUNTING BRACKET
1. Remove protective caps(front and
back) on the lens.
2. Mount the lens on mounting bracket
of the main cabinet with 4 screws.
Use the screws included with the lens.
Use the driver included with the lens to
fasten the screws.
(After using, keep it for latter use.)
ATTACHED DRIVER
Fig-4
INSTALL THE LIGHT-BLOCK SHEET. (See figure-5)
4
Install the light-block sheet around the lens
as shown in the illustration. Use the sheet
included with the lens.
Make sure the part no. and mark (TOP and
BACK) on Light-Block Sheet and set them
properly.
ADJUST FOCUS
Adjust focus following Focus Adjustment on
page 6.
Fig-5
LIGHT-BLOCK SHEET
Type FE1
(Part No. 610 280 2634)
MOUNT THE LENS COVER. (See figure-6)
5
UPPER LENS COVER
When in install the both upper and lower
lens covers, install the light-block sheet so
that it should be placed in the guide slot.
(place of the cover plate had been placed.
See figure-2.) If the installation of light-block
sheet is incorrect, it will be the cause of
leakage of light or the dust entering at the
main cabinet.
A
1. Insert the upper part lens cover and fix
them with screws A (4 screws).
A
2. Insert the lower part lens cover and fix
them with screws B. (2 screws).
B
Fig-6
LOWER LENS COVER
-3-
Download from Www.Somanuals.com. All Manuals Search And Download.
(Type 2 Cabinet)
LENS REPLACEMENT AND INSTALLATION PROCEDURE
1
7
Perform the steps
to
for lens replacement and installation.
First set the lens at the center position with lens shift adjustment.
A
REMOVE THE UPPER LENS COVER. (See figure-1)
1
1. Remove screws A (2 screws).
UPPER LENS
COVER
2. Push part B and pull Upper Lens Cover up.
B
Fig-1
REMOVE THE LOWER LENS COVER. (See figure-2)
2
C
1. Remove screws C (4 screws).
2. Pull Lower Lens Cover toward front and
remove.
LOWER LENS
COVER
C
Fig-2
REMOVE THE COVER PLATE. (See figure-3)
3
D
1. Remove screws D (2 screws) and Cover
Plate on the back of Upper Lens Cover.
6
(At the step
, insert the light-block sheet in
the same position as the removed cover plate
has been placed. Two screws are not used.)
UPPER LENS
COVER
Fig-3
COVER PLATE
-4-
Download from Www.Somanuals.com. All Manuals Search And Download.
DISCONNECT THE LENS SHIFT CONNECTORS. (See figure-4)
4
Disconnect the Lens Shift Connectors
("K96S" and "K96R") from circuit board.
LEAD
HOLDER
CONNECTOR
"K96S"
CONNECTOR
"K96R"
Fig-4
INSTALL THE LENS. (See figure-5)
5
1. Remove protective caps(front and
back) on the lens.
LENS MOUNTING BRACKET
2. Mount the lens on mounting bracket
of the main cabinet with 4 screws.
Use the screws included with the lens.
Use the driver included with the lens to
fasten the screws.
(After using, keep it for latter use.)
ATTACHED DRIVER
Fig-5
INSTALL THE LIGHT-BLOCK SHEET. (See figure-6)
6
Install the light-block sheet around the lens
as shown in the illustration. Use the sheet
included with the lens.
Make sure the part no. and mark (TOP and
BACK) on Light-Block Sheet and set them
properly.
ADJUST FOCUS
Adjust focus following Focus Adjustment on
page 6.
LIGHT-BLOCK SHEET
Type FB1
Fig-6
(Part No. 610 285 8211)
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
MOUNT THE LENS COVER. (See figure-7)
7
1. Replace Lower Lens Cover. Slide Light-Block Sheet into the guide of Lower Lens Cover
and set them in front of the flap. (See Fig. 7.) Fix Lower Lens Cover with 4 Screws C.
(See Fig. 2.)
2. Replace Upper Lens Cover. Slide Light-Block Sheet into the guide of Upper Lens Cover
and set them in front of the flap. (See Fig. 7.) Fix Upper Lens Cover with 2 Screws A.
(See Fig. 1.)
Slide upper both side of LIGHT BLOCK
2
Sheet into between 1 and
CABINET
.
1
Fig-7
Slide into front
of the flap.
FLAP
UPPER LENS
COVER
GUIDE
2
LIGHT-BLOCK
SHEET
Slide into front
of the flap.
FLAP
LOWER LENS
COVER
FOCUS ADJUSTMENT
Set up the projector and project image on the screen.
1. Loosen the Focus Lock Screw on the projection
lens.
2. Rotate the projection lens to obtain proper focus
on center area of the screen.
mark (yellow)
When the distance of the screen and lens is 1 meter,
set mark (yellow) of the lens on Focus Lock Screw
position.
3. Lock the Focus Lock Screw securely.
When proper focus is not observed at outer area of
the screen, proceed following adjustments.
4. Loosen the Focus Lock Ring on the projection
lens. (Turn the Lock Ring to counter-clockwise.)
5. Rotate the lens to obtain proper focus on outer
area of the screen.
Focus Lock Ring
Focus Lock Screw
6. Lock the Focus Lock Ring securely. (Turn the Lock
Ring to clockwise.)
If proper focus is not observed entire screen, repeat
above adjustment 1~ 6.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
|