OWNER'S OPERATING MANUAL
ROUTER - R160 / R165
DOUBLE INSULATED
SPECIFICATIONS:
Depth Of Cut
0 - 1-1/2 In. (0 - 38.1mm)
1/4 In. (6.4mm)
Collet
Horsepower
R160
R165
1-1/2
1-3/4
Rating
120 Volts, 60 Hz, AC Only
Amperes
R160
R165
8.0
8.5
No Load Speed
Net Weight
25,000 RPM
7.8 Lbs.
THANK YOU FOR BUYING A RYOBI ROUTER.
Your new router has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire owner's manual before using your new router. Pay close attention
to the Rules for Safe Operation, Warnings, and Cautions. If you use your router properly and only for what it is intended, you
will enjoy years of safe, reliable service.
Thank you again for buying a Ryobi router.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
THE PURPOSE OF SAFETY SYMBOLS IS TO ATTRACT YOUR ATTENTION TO POSSIBLE DANGERS. THE
SAFETY SYMBOLS, AND THE EXPLANATIONS WITH THEM, DESERVE YOUR CAREFUL ATTENTION AND
UNDERSTANDING. THE SAFETY WARNINGS DO NOT BY THEMSELVES ELIMINATE ANY DANGER. THE
INSTRUCTIONS OR WARNINGS THEY GIVE ARE NOT SUBSTITUTES FOR PROPER ACCIDENT PREVENTION
MEASURES.
SYMBOL
MEANING
SAFETY ALERT SYMBOL:
Indicates caution or warning. May be used in conjunction with other symbols or pictographs.
WARNING: Failure to obey a safety warning can result in serious injury to yourself or to
others. Always follow the safety precautions to reduce the risk of fire, electric shock and
personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury
to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric
shock and personal injury.
DOUBLE INSULATION
IMPORTANT
Your Ryobi power tool is double insulated. This means you Servicing of a tool with double insulation requires extreme
areseparatedfromthetool'selectricalsystembytwocomplete care and knowledge of the system and should be performed
sets of electrical insulation. This extra layer of insulation is only by a qualified service technician. For service we suggest
intended to protect the user from electrical shock due to a you return the tool to your nearest RYOBI AUTHORIZED
break in the wiring insulation. All exposed metal parts are SERVICE CENTER for repair. When servicing use only
isolated from the internal metal motor components with identical Ryobi replacement parts.
protecting insulation. Double insulated tools do not need to
be grounded.
WARNING:
WARNING:
Do not attempt to operate this tool until you have read
thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to
comply can result in accidents involving fire, electric
shock, or serious personal injury. Save owner's manual
and review frequently for continuing safe operation, and
instructing others who may use this tool.
The double insulated system is intended to protect the
user from shock resulting from a break in the tool's
internal wiring. Observe all normal safety precautions
related to avoiding electrical shock.
WARNING:
WEAR YOUR
The operation of any router can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face shield when
needed. We recommend Wide Vision Safety Mask for use over eyeglasses or standard
safety glasses with side shields.
SAFETY
GLASSES
FORESIGHT IS BETTER
THAN NO SIGHT
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
READ ALL INSTRUCTIONS
1. KNOW YOUR POWER TOOL. Read owner's
manual carefully. Learn its applications and
limitations as well as the specific potential
hazards related to this tool.
17. MAINTAIN TOOLS WITH CARE. Keep tools
sharp at all times, and clean for best and safest
performance. Follow instructions for lubricating
and changing accessories.
2. GUARD AGAINST ELECTRICAL SHOCK by
preventing body contact with grounded surfaces.
For example: Pipes, radiators, ranges,
refrigerator enclosures.
18. DISCONNECT TOOLS. When not in use, before
servicing, or when changing attachments, blades,
bits, cutters, etc., all tools should be disconnected
from power supply.
3. KEEP GUARDS IN PLACE and in working order.
4. KEEP WORK AREA CLEAN. Cluttered areas
19. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see
that keys and adjusting wrenches are removed
from tool before turning it on.
20. AVOID ACCIDENTAL STARTING. Don't carry
plugged-in tools with finger on switch. Be sure
switch is off when plugging in.
21. MAKE SURE YOUR EXTENSION CORD IS IN
GOOD CONDITION. When using an extension
cord, be sure to use one heavy enough to carry
the current your product will draw. An undersized
cord will cause a drop in line voltage resulting in
loss of power and overheating. A wire gage size
(A.W.G.) of at least 14 is recommended for an
extension cord 50 feet or less in length. A cord
exceeding 50 feet is not recommended. If in
doubt, use the next heavier gage. The smaller the
gage number, the heavier the cord.
22. OUTDOOR USE EXTENSION CORDS. When
tool is used outdoors, use only extension cords
suitable for use outdoors. Outdoor approved
cords are marked with the suffix W-A, for example
- SJTW-A or SJOW-A.
and benches invite accidents.
5. AVOID DANGEROUS ENVIRONMENT. Don't
use power tool in damp or wet locations or expose
to rain. Keep work area well lit.
6. KEEP CHILDREN AND VISITORS AWAY. All
visitors should wear safety glasses and be kept
a safe distance from work area. Do not let
visitors contact tool or extension cord.
7. STORE IDLE TOOLS. When not in use tools
should be stored in a dry and high or locked-up
place - out of the reach of children.
8. DON'T FORCE TOOL. It will do the job better
and safer at the rate for which it was designed.
9. USE RIGHT TOOL. Don't force small tool or
attachment to do the job of a heavy duty tool.
Don't use tool for purpose not intended - for
example - A circular saw should never be used
for cutting tree limbs or logs.
10. WEAR PROPER APPAREL. Do not wear loose
clothing or jewelry that can get caught in tool's
moving parts and cause personal injury. Rubber
gloves and nonskid footwear are recommended
when working outdoors. Wear protective hair
covering to contain long hair and keep it from
being drawn into nearby air vents.
11. ALWAYS WEAR SAFETY GLASSES. Everyday
eyeglasses have only impact-resistant lenses;
they are NOT safety glasses.
12. PROTECT YOUR LUNGS. Wear a face or dust
mask if operation is dusty.
13. PROTECT YOUR HEARING. Wear hearing
23. KEEP CUTTERS CLEAN AND SHARP. Sharp
cutters minimize stalling and kickback.
24. KEEP HANDS AWAY FROM CUTTING AREA.
Keep hands away from cutters. Do not reach
underneath work while cutter is rotating. Do not
attempt to remove material while cutter is rotating.
25. NEVER USE IN AN EXPLOSIVE ATMO-
SPHERE. Normal sparking of the motor could
ignite fumes.
26. INSPECT TOOL CORDS PERIODICALLY and
if damaged, have repaired at your nearest
authorized service center. Stay constantly aware
of cord location.
protection during extended periods of operation.
14. DON'T ABUSE CORD. Never carry tool by cord
or yank it to disconnect from receptacle. Keep
cord from heat, oil and sharp edges.
15. SECURE WORK. Use clamps or a vise to hold
work. Both hands are needed to operate the
tool.
16. DON'T OVERREACH. Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
27. INSPECT EXTENSION CORDS PERIODI-
CALLY and replace if damaged.
28. KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brake fluids,
gasoline, petroleum-based products or any strong
solvents to clean your tool.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION (Continued)
29. STAY ALERT. Watch what you are doing and
use common sense. Do not operate tool when
you are tired. Do not rush.
36. DO NOT USE TOOL UNDER "BROWNOUT"
OR OTHER LOW VOLTAGE CONDITIONS.
Also, do not use with any device that could cause
the power supply voltage to change.
37. WHEN USING THIS ROUTER WITH A ROUTER
TABLE, HELP PREVENT POSSIBLE SERIOUS
INJURY BY KEEPING THE CUTTER
GUARDED AT ALL TIMES. Use only UL listed
router tables, with guards, that have been
designed for use on routers that are of this type,
size, and weight.
30. CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorized service center unless indicated
elsewhere in this instruction manual.
38. SAVE THESE INSTRUCTIONS. Review them
frequently and use them to instruct others who
may use this tool. If you loan someone this tool,
loan them these instructions also.
31. DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have switches replaced
by an authorized service center.
WARNING:
32. INSPECT FOR and remove all nails from lumber
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
before routing.
33. DRUGS, ALCOHOL, MEDICATION. Do not
operate tool while under the influence of drugs,
alcohol, or any medication.
34. WHEN SERVICING, USE ONLY IDENTICAL
• lead from lead-based paints,
RYOBI REPLACEMENT PARTS.
• crystalline silica from bricks and cement and other
masonry products, and
35. POLARIZED PLUGS. To reduce the risk of
electric shock, this tool has a polarized plug (one
blade is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug
in any way.
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
SAVE THESE INSTRUCTIONS
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
WARNING:
If any parts are missing, do not operate your router until
the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
Always wear safety goggles or safety glasses with side
shields when operating your router. Failure to do so could
result in dust, shavings, loose particles or foreign objects
being thrown into your eyes, causing possible serious
injury.
UNPACKING
Your router has been shipped completely assembled and
ready for use. Inspect it carefully to make sure no breakage
or damage has occurred during shipping. If any parts are
damaged or missing, contact your nearest Ryobi dealer to
obtainreplacementpartsbeforeattemptingtooperaterouter.
A wrench, owner's operating manual, and warranty
CHIP SHIELD
A clear plastic chip shield is installed on the front of your
router for protection against flying dust and chips. The shield
is designed to fit the front opening of the router base. See
Figure 1. If necessary to remove chip shield, squeeze the
tabs on each end and pull outward. To replace, squeeze the
tabs at each end, fit into opening, then release. FOR YOUR
PROTECTION, DO NOT USE ROUTER WITHOUT CHIP
SHIELD PROPERLY IN PLACE.
registration are also included.
KNOW YOUR ROUTER
Beforeattemptingtouseyourrouter,familiarizeyourselfwith
alloperatingfeaturesandsafetyrequirements. SeeFigure1.
"LOCK-ON BUTTON"
The switch of your router is equipped with a "lock-on" feature
which is convenient when operating for extended periods of
time. To lock on, depress the trigger, push in the lock button
located on the side of the handle, then while holding the lock
button pushed in, release the trigger. To release the lock,
depress the trigger and release it. See Figure 1.
WARNING:
Do not allow familiarity with your router to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict severe injury.
UPSIDE DOWN VIEW OF ROUTER
DEPTH
INDICATOR
RING(S)
INDICATOR
POINT(S)
64
3
7
32
1
32
15
0
64
1
64
SPINDLE
LOCK
"LOCK-ON
BUTTON"
INDICATOR
POINT(S)
DEPTH
ADJUSTING
RING
1 3
3
64
3
3 16
7
64
11
6
4
1
8
5 32
9 64
HANDLE
DEPTH
INDICATOR
RING(S)
P O W E R
H A N D L E
CLAMPING
LEVER
D E P T H
ADJUSTING
R I N G
CHIP
SHIELD
SWITCH
TRIGGER
SUBBASE WITH
STRAIGHT EDGE
FRONT VIEW OF ROUTER
REAR VIEW OF ROUTER
Fig. 1
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
SPINDLE LOCK
WARNING:
Your router should never be connected to power supply
when you are assembling parts, making adjustments,
installing or removing cutters, or when not in use.
Disconnecting your router will prevent accidental starting
that could cause serious injury.
1
3
1
INSTALLING/REMOVING CUTTERS
See Figures 2 and 3.
2
3
2
1. UNPLUG YOUR ROUTER.
TO UNLOCK
SPINDLE
TO LOCK
SPINDLE
WARNING:
Fig. 2
Failure to unplug your router could result in accidental
starting causing serious injury.
CUTTER
WRENCH
COLLET
NUT
WARNING:
To prevent damage to the spindle or spindle lock, always
allow motor to come to a complete stop before engaging
spindle lock.
TO LOOSEN
COLLET NUT
64
0
1
5
2. A spindle lock is located on the top of the end cap. See
Figure 2. To activate lock, (1) push spindle lock in, (2)
slide into lock position, then (3) release spindle lock.
64
7
32
3. Place your router upside down on table, then turn collet
nut with wrench until lock mechanism interlocks. See
Figure 3. NOTE: Spindle lock is spring loaded and will
snap into position when lock mechanism interlocks.
TO TIGHTEN
COLLET NUT
Fig. 3
WARNING:
If you are changing a cutter immediately after use, be
careful not to touch the cutter or collet with your hands or
fingers. They will get burned because of the heat buildup
from cutting. Always use the wrench provided.
WARNING:
Do not use cutters with undersized shanks. Undersized
shanks will not tighten properly and could be thrown from
tool causing injury.
4. Remove cutters by turning collet nut counterclockwise
enough to allow cutter to slip easily from collet. See
Figure 3. The collet is machined to precision tolerances
to fit cutters with 1/4 in. diameter shank size.
ELECTRICAL CONNECTION
Your router has a precision built electric motor. It should be
connected to a power supply that is 120 volts, 60 Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A voltage drop of more than 10
percent will cause a loss of power and the motor will
overheat. If your tool does not operate when plugged into an
outlet, double-check the power supply.
5. With your router still upside down on table, insert shank
of cutter into collet. The shank of your cutter should be
close to but not touching bottom of collet.
6. Tighten the collet nut securely by turning clockwise
with the wrench provided. See Figure 3. Put spindle
lock back in unlock position. Otherwise, the interlock-
ing mechanism of the spindle lock will not let you turn
your router on. To unlock spindle, (1) push spindle lock
in, (2) slide into unlock position, then (3) release spindle
lock. See Figure 2.
WARNING:
Before connecting your router to power supply, always
checktobesureswitchisnotin"lock-on"position. Failure
to do so could result in accidental starting of your router
resulting in possible serious injury.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DEPTH OF CUT ADJUSTMENTS
See Figures 4, 5, 6, and 7.
DEPTH
INDICATOR
RING
We recommend that cuts be made at a depth not exceeding
1/8 in. and that several passes be made to reach depths of
cut greater than 1/8 in.
INDICATOR
POINT
1. UNPLUG YOUR ROUTER.
WARNING:
Failure to unplug your router could result in accidental
starting causing serious injury.
2. Place your router on a flat surface, unlock clamping
lever, and turn depth adjusting ring until cutter is inside
subbase. See Figures 4 and 5.
DEPTH
ADJUSTING
RING
3. Turn the depth adjusting ring until tip of cutter touches
flat surface (zero depth of cut). See Figure 6. Next turn
depth indicator ring until the zero lines up with the
indicator point on front of motor housing. See Figure 5.
CUTTER
INSIDE SUBBASE
Fig. 5
SUBBASE
4. Position your router so that the cutter can extend below
the subbase for desired depth setting.
5. Turn the depth adjusting ring to obtain the desired
depth of cut. The distance the cutter moves can be
read on the depth adjusting ring. Each mark on the
depth adjusting ring indicates 1/64 inch change in depth
setting. One indicator point is located on front of the
motor housing, the other one is located on the base.
6. Lock clamping lever, securing depth adjusting ring to
motor housing and base.
DEPTH OF CUT ADJUSTMENTS WHEN
ROUTER IS MOUNTED TO A ROUTER TABLE
See Figure 7.
The depth of cut is readable from both sides of the depth
adjusting ring. There is a depth indicator ring and indicator
point on both sides of the depth adjusting ring. The bottom
ring is convenient when using your router mounted to a
router table. The indicator point on the base should also be
used when using your router mounted to a router table.
CUTTER AT
ZERO DEPTH OF CUT
Fig. 6
The depth indicator rings are identical parts. Therefore,
when you have your router mounted upside down on a
router table, you set depth of cut by reading the scale
different. Set the cutter at zero depth of cut, rotate depth
indicator ring to desired depth of cut on the scale, then turn
depth adjusting ring back to zero depth of cut and lock
clamping lever securely.
FOR ROUTER TABLE USE ONLY
CLAMPING
LEVER
TO
LOCK
C
K
O
L
U
K
BASE
N
C
L
O
DEPTH
INDICATOR
RING
INDICATOR
POINT
TO
UNLOCK
Fig. 4
Page 8
Fig. 7
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ROUTING
For ease of operation and maintaining proper control, your
router has two handles, one on each side of the router base.
When using your router hold it firmly with both hands as
shown in figure 8. Turn router on and let motor build to its full
speed, then gradually feed cutter into workpiece. Remain
alert and watch what you are doing. DO NOT operate router
when fatigued.
PROPER FEEDING
The right feed is neither too fast nor too slow. It is the rate at
which the bit is being advanced firmly and surely to produce
a continuous spiral of uniform chips — without hogging into
thewoodtomakelargeindividualchipsor,ontheotherhand,
to create only sawdust. If you are making a small diameter,
shallow groove in soft, dry wood, the proper feed may be
about as fast as you can travel your router along your guide
line. On the other hand, if the bit is a large one, the cut is deep
or the wood is hard to cut, the proper feed may be a very slow
one. Then, again, a cross-grain cut may require a slower
pace than an identical with grain cut in the same workpiece.
Fig. 8
There is no fixed rule. You will learn by experience. . . by
listening to the router motor and by feeling the progress of
each cut. If at all possible, always test a cut on a scrap piece
of the workpiece wood, beforehand.
RATE OF FEED
IMPORTANT: The whole "secret" of professional routing
and edge shaping lies in making a careful setup for the cut
to be made and in selecting the proper rate of feed.
TOO FAST
FORCE FEEDING
Clean, smooth routing and edge shaping can be done only
when the bit is revolving at a relatively high speed and is
taking very small bites to produce tiny, cleanly severed
chips. If your router is forced to move forward too fast, the
RPM of the bit becomes slower than normal in relation to its
forward movement. As a result, the bit must take bigger bites
as it revolves. “Bigger bites” mean bigger chips, and a
rougher finish. Bigger chips also require more power, which
could result in the router motor becoming overloaded.
Fig. 9
TOO SLOW
Under extreme force-feeding conditions the relative RPM of
the bit can become so slow—and the bites it has to take so
large—that chips will be partially knocked off (rather than
fully cut off), with resulting splintering and gouging of the
workpiece. See Figure 9.
TOO SLOW FEEDING
It is also possible to spoil a cut by moving the router forward
too slowly. When it is advanced into the work too slowly, a
revolving bit does not dig into new wood fast enough to take
abite;instead, itsimplyscrapesawaysawdust-likeparticles.
Scraping produces heat, which can glaze, burn, or mar the
cut— in extreme cases, can even overheat the bit so as to
destroy its hardness.
Your Ryobi Router is an extremely high-speed tool (25,000
RPM no-load speed), and will make clean, smooth cuts if
allowed to run freely without the overload of a forced (too
fast) feed. Three things that cause “force feeding” are bit
size, depth-of-cut, and workpiece characteristics. The larger
the bit or the deeper the cut, the more slowly the router
should be advanced. If the wood is very hard, knotty, gummy
or damp, the operation must be slowed still more.
In addition, it is more difficult to control a router when the bit
is scraping instead of cutting. With practically no load on the
motor the bit will be revolving at close to top RPM, and will
have a much greater than normal tendency to bounce off the
sides of the cut (especially, if the wood has a pronounced
grain with hard and soft areas). As a result, the cut produced
may have rippled, instead of straight sides. See Figure 9.
You can always detect “force feeding” by the sound of the
motor. Its high-pitched whine will sound lower and stronger
as it loses speed. Also, the strain of holding the tool will be
noticeably increased.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TOO SLOW FEEDING (Continued)
“Too-slow feeding” can also cause your router to take off in
a wrong direction from the intended line of cut. Always
grasp and hold your router firmly with both hands when
routing.
DEPTH
OF CUT
WIDTH
OF CUT
You can detect “too-slow feeding” by the runaway too-highly
pitched sound of the motor; or by feeling the “wiggle” of the
bit in the cut.
Fig. 10
DEPTH OF CUT
As previously mentioned, the depth of cut is important
because it affects the rate of feed which, in turn, affects the
quality of a cut (and, also, the possibility of damage to your
router motor and bit). A deep cut requires a slower feed than
a shallow one, and a too deep cut will cause you to slow the
feed so much that the bit is no longer cutting, it is scraping,
instead .
2ND. PASS
1ST.
PASS
1ST. PASS
2ND.
PASS
Making a deep cut is never advisable. The smaller bits—
especially those only 1/16 inch in diameter —are easily
broken off when subjected to too much side thrust. A large
enough bit may not be broken off, but if the cut is too deep a
rough cut will result— and it may be very difficult to guide and
controlthebitasdesired. Forthesereasons, werecommend
that you do not exceed 1/8 inch depth of cut in a single pass,
regardless of the bit size or the softness or condition of the
workpiece. See Figure 10.
Fig. 11
GUIDE OUTSIDE
ROTATION
THRUST
ROTATION
FEED
To make deeper cuts it is therefore necessary to make as
many successive passes as required, lowering the bit 1/8
inch for each new pass. In order to save time, do all the
cutting necessary at one depth setting, before lowering the
bit for the next pass. This will also assure a uniform depth
when the final pass is completed. See Figure 11.
GUIDE
DIRECTION OF FEED AND THRUST
GUIDE
Theroutermotorandbitrevolveinaclockwisedirection.This
gives the tool a slight tendency to twist (in your hands) in a
counterclockwise direction, especially when the motor revs
up (as at starting).
FEED
ROTATION
THRUST
GUIDE INSIDE
Fig. 12
Because of the extremely high speed of bit rotation during a
“proper feeding” operation, there is very little kickback to
contend with under normal conditions. However, should the
bit strike a knot, hard grain, foreign object, etc. that would
affect the normal progress of the cutting action, there will be
a slight kickback—sufficient to spoil the trueness of your cut
if you are not prepared. Such a kickback is always in the
direction opposite to the direction of bit rotation.
ROUTING
Whenever you are routing a groove, your travel should be in
a direction that places whatever guide you are using at the
right-hand side. In short, when the guide is positioned as
shown in the first part of Figure 12, tool travel should be left
to right and counterclockwise around curves. When the
guide is positioned as shown in the second part of Figure 12,
tool travel should be right to left and clockwise around
curves. If there is a choice, the first setup is generally the
easiest to use. In either case, the sideways thrust you use is
against the guide.
To guard against such a kickback, plan your setup and
direction of feed so that you will always be thrusting the
tool—to hold it against whatever you are using to guide the
cut—in the same direction that the leading edge of the bit is
moving.Inshort,thethrustshouldbeinadirectionthatkeeps
the sharp edges of the bit continuously biting straight into
new (uncut) wood.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
STARTING AND ENDING A CUT
INTERNAL ROUTING
ROUTER
WORK
Tilt router and place on workpiece, letting edge of subbase
contact workpiece first. Be careful not to let router bit contact
workpiece. Turnrouteronandletmotorbuildtoitsfullspeed.
Gradually feed cutter into workpiece until subbase is level
with workpiece.
PILOT
GUIDE
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
TOP EDGE SHAPING
ROUTER
WORK
Upon completion of cut, turn motor off and let it come to a
complete stop before removing router from work surface.
WARNING:
PILOT
Never pull router out of work and place upside down on
work surface before the cutter stops.
WHOLE EDGE SHAPING
Fig. 13
EDGING WITH PILOT BITS
The arbor-type bits with pilots are excellent for quick, easy,
edge shaping of any workpiece edge that is either straight or
curved at a curvature as great or greater than the radius of
the bit to be used. The pilot prevents the bit from making too
deep a cut; and holding the pilot firmly in contact with the
workpiece edge throughout prevents the cut from becoming
too shallow.
EDGE ROUTING
Place router on workpiece, making sure the router bit does
not contact workpiece. Turn router on and let motor build to
its full speed. Begin your cut, gradually feeding cutter into
workpiece.
Whenevertheworkpiecethicknesstogetherwiththedesired
depth of cut (as adjusted by router depth setting) are such
that only the top part of the edge is to be shaped (leaving at
least a 1/16 inch thick uncut portion at bottom), the pilot can
ride against the uncut portion, which will serve to guide it.
See Figure 13. However, if the workpiece is too thin or the
bit set too low so that there will be no uncut edge to ride the
pilot against, an extra board to act as a guide must be placed
under the workpiece. This “guide” board must have exactly
the same contour— straight or curved—as the workpiece
edge. If it is positioned so that its edge is flush with the
workpiece edge, the bit will make a full cut (in as far as the
bit radius). On the other hand, if the guide is positioned as
shown in Figure 13 (out from the workpiece edge), the bit will
make less than a full cut — which will alter the shape of the
finished edge.
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
Upon completion of cut, turn motor off and let it come to a
complete stop before removing router from work surface.
WARNING:
Never pull router out of work and place upside down on
work surface before the cutter stops.
NOTE: Any of the piloted bits can be used without a pilot for
edge shaping with guides, as preceding. The size (diameter)
of the pilot that is used determines the maximum cut width
that can be made with the pilot against the workpiece edge
(the small pilot exposes all of the bit; the large one reduces
this amount by 1/16 inch).
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
FREEHAND ROUTING
See Figure 14.
When used freehand, your router becomes a flexible and
versatile tool. This flexibility makes it possible to easily rout
signs, relief sculptures, etc.
There are two basic techniques for freehand routing:
1. Routing letters, grooves, and patterns into wood. See
Figure 14.
2. Routing out the background, leaving the letters or
pattern raised above the surface.
When freehand routing, we suggest the following:
1. Draw or layout the pattern on workpiece.
2. Choose the appropriate cutter. NOTE: A core box or
V-groove bit is often used for routing letters and
engraving objects. Straight bits and ball mills are often
used to make relief carvings. Veining bits are used to
carve small, intricate details.
3. Rout the pattern in two or more passes. Make the first
pass at 25% of the desired depth of cut. This will
provide better control as well as being a guide for the
next pass.
4. Do not rout deeper than 1/8 in. per pass or cut.
FREEHAND ROUTING
Fig. 14
WARNING:
Do not use large router bits for freehand routing. Use of
large router bits when freehand routing could cause loss
of control or create other hazardous conditions that could
cause possible serious personal injury. When using a UL
listed router table, large router bits should be used for
edging only. Do not use router bits that are larger in
diameter than the opening in router base.
1
3
3
6
4
3
3
16
7
64
1
8
5
32
9
64
ROUTINGWITHSTRAIGHTEDGEOFSUBBASE
See Figure 15.
The subbase on your router has a straight edge. It should be
used when placing your router against an edge guide or
fence and routing grooves parallel to the fence.
WARNING:
Do not use with router tables that fail to conform to safe
wood working practices and offer proper guarding for the
cutter. Failure to comply can result in an accident causing
possible serious injury.
ROUTING WITH STRAIGHT EDGE OF
SUBBASE AGAINST AN EDGE GUIDE
Fig. 15
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
LIGHT BULB REPLACEMENT (MODEL NO.
R165 ONLY)
See Figure 16.
ROUTER MODEL R165 (ONLY)
A
1. UNPLUG YOUR ROUTER.
WARNING:
Failure to unplug your router could result in accidental
starting causing serious injury.
B
C
2. Remove cutter from router. Refer to page 7 to remove
cutter.
E
D
3. Adjust router to maximum height.
4. Remove screws (A) and subbase (B). See Figure 16.
5. Remove screw (C) and work light lens (D).
6. With bulb (E) pointing toward you, pull bulb from socket.
7. Install new bulb by reversing the above procedure.
8. Reassemble all parts and tighten screws securely.
Fig. 16
PROPER CARE OF CUTTERS
PROPER CARE OF COLLET
Get faster more accurate cutting results by keeping cutters
clean and sharp. Remove all accumulated pitch and gum
from cutters after each use.
From time to time, it also becomes necessary to clean your
collet and collet nut. To do so, simply remove collet nut from
collet and clean the dust and chips that have collected. Then
return collet nut to its original position. DO NOT tighten collet
nut on collet without a cutter installed.
When sharpening cutters, sharpen only the inside of the
cutting edge. Never grind the outside diameter. Be sure
when sharpening the end of a cutter to grind the clearance
angle the same as originally ground.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normaloperatingconditions. Therefore,nofurtherlubrication
is required.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
WARNING:
When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product
damage.
GENERAL
Avoidusingsolventswhencleaningplasticparts.Mostplastics
are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use clean cloths
to remove dirt, carbon dust, etc.
When electric tools are use on fiberglass boats, sports cars,
wallboard, spackling compounds, or plaster, it has been
found that they are subject to accelerated wear and possible
premature failure, as the fiberglass chips and grindings are
highly abrasive to bearings, brushes, commutators, etc.
Consequently, it is not recommended that this tool be used
for extended work on any fiberglass material, wallboard,
spackling compounds, or plaster. During any use on these
materials, it is extremely important that the tool is cleaned
frequently by blowing with an air jet.
WARNING:
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc. come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
WARNING:
Always wear safety goggles or safety glasses with side
shieldsduringpowertooloperationorwhenblowingdust.
If operation is dusty, also wear a dust mask.
OPTIONAL ACCESSORIES
The following recommended accessories are current and were available at the time this manual was printed:
ITEM NO.
DESCRIPTION
4070175
4070176
4090125
6090080
Template Guide Adapter For Ryobi Template Guides
Template Guide Adapter For Porter Cable Rockwell and B&D Template Guides
Dust Pickup Adapter For Ryobi Routers - Model Nos. R160, R165, R175 and RE175
Straight Guide For Ryobi Routers - Model Nos. R160, R165, R175 and RE175
HELPFUL HINTS
ꢀ Always clamp workpiece securely before routing.
ꢀ A safe operator is one who thinks ahead.
ꢀ Always wear eye protection when routing.
ꢀ Make setup adjustments carefully. Then double check. Measure twice and cut once.
ꢀ Keep cutters clean and properly sharpened.
ꢀ Don’t let familiarity make you careless.
ꢀ Study all safety rules and do the job safely.
ꢀ NEVER place your hands in jeopardy.
ꢀ Make certain clamps can’t loosen while in use.
ꢀ Test difficult setups on scrap—Don’t waste lumber.
ꢀ Plan each operation before you begin.
ꢀ Clean your router frequently. This will provide smoother operation of depth adjusting ring and clamping lever areas.
Shake router or blow with an air jet to remove sawdust buildup.
ꢀ THINK SAFETY BY THINKING AHEAD.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER'S OPERATING MANUAL
ROUTER - R160 / R165
DOUBLE INSULATED
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or service,
simplycontactyournearestRyobiAuthorizedServiceCenter. Besuretoprovideallpertinent
facts when you call or visit. Please refer to the Service Center insert or call 1-800-525-2579
in the United States or 1-800-265-6778 in Canada for your nearest Ryobi Authorized Service
Center.
• MODEL NO.
The model number and serial number of your tool will be found on a plate attached to the
motor housing. Please record the model number and serial number in the space provided
below.
• HOW TO ORDER REPAIR PARTS
WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION:
•
•
MODEL NUMBER
SERIAL NUMBER
RYOBI CANADA INC.
P.O. Box 910
RYOBI AMERICA CORPORATION
1424 Pearman Dairy Road Anderson SC 29625
Cambridge, Ontario N1R 6K2
Phone 1-800-265-6778
Post Office Box 1207
Anderson SC 29622-1207
Phone 1-800-525-2579
972000-227
7-00
PrintedinU.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
NOTE ALL WIRING IN THE HANDLE AND HOW EACH
SWITCH REPLACEMENT
LEAD IS CONNECTED TO THE SWITCH. Connections
and wiring position must be identical when installing
new switch. See Figure 16.
See Figure 16.
1. Before attempting to replace the switch on your router,
you must know the model of your router (Model No.
R160 or Model No. R165). To replace switch, follow the
steps and illustrations below.
5. Remove leads from switch (D) by inserting a 1/32 in.
diameter nail or pin into switch lead receptacle and
pulling on lead as shown in figure 16. Remove nail or
pin with a twisting, pulling motion.
2. UNPLUG YOUR ROUTER.
6. Make lead connections to new switch. Push each lead
as far as possible into proper switch receptacle. Pull on
leads to check lead connections with lead receptacles.
7. Locate switch in handle and place leads so they won't
be pinched or contact screws when handle cover is
replaced.
8. Make sure molded bend relief (C) is correctly positioned
in switch handle, then replace handle cover and screws.
9. Tighten all screws securely.
WARNING:
Failure to unplug your router could result in accidental
starting causing serious injury.
3. Remove screws (A) and handle cover (B). See Figure
16.
4. NOTE THE LOCATION OF THE MOLDED BEND
RELIEF (C) ON THE POWER HANDLE CORD. ALSO
SWITCH REPLACEMENT FOR MODEL NO. R160
POWER HANDLE CORD
1/32 INCH DIAMETER
NAIL OR PIN
C
D
B
BLACK LEAD
A
WHITE LEAD
SWITCH
SWITCH REPLACEMENT FOR MODEL NO. R165
POWER HANDLE CORD
1/32 INCH DIAMETER
NAIL OR PIN
BLACK LEAD
C
WHITE LEAD
B
D
A
RED
WORKLIGHT LEAD
RED POWER
CORD LEAD
SWITCH
RED
WORKLIGHT LEAD
Fig. 16
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
|