OWNER’S OPERATING MANUAL
CL-610 Series
TM
Digital Light Processing Projectors
CL-610
CL-610LT
CL-610 CineWide
CL-610LT CineWide
TM
TM
Download from Www.Somanuals.com. All Manuals Search And Download.
TWO YEAR LIMITED WARRANTY
For Projectors, Video Processors and Controllers
Congratulations on your purchase of a Runco video product and welcome to the Runco family! With proper installation, setup
and care, you should enjoy many years of unparalleled video performance.
This is a LIMITED WARRANTY as defined in the Magnuson-Moss Warranty Act. Please read it carefully and retain it with your
other important documents.
WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
SERVICE LABOR: Runco will pay for service labor by Runco Authorized Service Center when needed as a result of
manufacturing defect for a period of two (2) years from the effective date of delivery to the end user (excluding the lamp).
PARTS (not including the lamp): Runco will provide new or rebuilt replacement parts for the parts that fail due to defects in
materials or workmanship for a period of two (2) years from the effective date of delivery to the end user. Such replacement
parts are then subsequently warranted for the remaining portion (if any) of the original warranty period.
PROJECTOR LAMP: Runco will pay for service labor by a Runco Authorized Service Center when needed as a result of a
manufacturing defect for a period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to
the end user. In addition, Runco will provide a new or rebuilt replacement lamp for the lamp that fails due to defects in materials
or workmanship for a period of six (6) months or 1000 hours, whichever comes first, from the effective date of delivery to the
end user. Such replacement lamps are then subsequently warranted for the remaining portion (if any) of the original warranty
period.
WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY:
This Limited Warranty only covers failure due to defects in materials and workmanship that occur during normal use and does
not cover normal maintenance. This Limited Warranty does not cover cabinets or any appearance items; failure resulting from
accident, misuse, abuse, neglect, mishandling, misapplication, faulty or improper installation or setup adjustments; improper
maintenance, alteration, improper use of any input signal; damage due to lightning or power line surges, spikes and
brownouts; damage that occurs during shipping or transit; or damage that is attributed to acts of God. In the case of remote
control units, damage resulting from leaking, old, damaged or improper batteries is also excluded from coverage under this
Limited Warranty.
CAUTION: THIS LIMITED WARRANTY ONLY COVERS VIDIKRON PRODUCTS PURCHASED FROM VIDIKRON AUTHORIZED
DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS WARRANTY.
MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS
SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. IT IS IMPERATIVE THAT INSTALLATION
AND SETUP WORK BE PERFORMED ONLY BY AN AUTHORIZED VIDIKRON DEALER TO PROTECT YOUR RIGHTS UNDER
THIS WARRANTY. THIS WILL ALSO ENSURE THAT YOU ENJOY THE FINE PERFORMANCE OF WHICH YOUR VIDIKRON
PRODUCT IS CAPABLE WHEN INSTALLED AND CALIBRATED BY VIDIKRON AUTHORIZED PERSONNEL.
RIGHTS, LIMITS AND EXCLUSIONS:
Runco limits its obligations under any implied warranties under state laws to a period not to exceed the warranty period. There
are no express warranties. Runco also excludes any obligation on its part for incidental or consequential damages related to
the failure of this product to function properly. Some states do not allow limitations on how long an implied warranty lasts, and
some states do not allow the exclusion or limitation of incidental or consequential damages. So the above limitations or
exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from
state to state.
Runco CL-610 Series Owner’s Operating Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
EFFECTIVE WARRANTY DATE:
This warranty begins on the effective date of delivery to the end user. For your convenience, keep the original bill of sale as
evidence of the purchase date.
IMPORTANT -- WARRANTY REGISTRATION:
Please fill out and mail your warranty registration card. It is imperative that Runco knows how to reach you promptly if we
should discover a safety problem or product update for which you must be notified.
CONTACT A VIDIKRON AUTHORIZED SERVICE CENTER TO OBTAIN SERVICE:
Repairs made under the terms of this Limited Warranty covering your Runco video product will be performed at the location of
the product, during usual working hours, providing location of product is within normal operating distance from a Runco
Authorized Service Center. In some instances it may be necessary for the product to be returned to the Runco factory for
repairs. If, solely in Runco’s judgment, location of product to be repaired is beyond normal operating distance of the closest
Runco Authorized Service Center, or the repair requires the unit be returned to the Runco factory, it is the owner’s
responsibility to arrange for shipment of the product for repair. These arrangements must be made through the selling Runco
Dealer. If this is not possible, contact Runco directly for a Return Authorization number and shipping instructions. Runco will
return product transportation prepaid in the United States, unless no product defect is discovered. In that instance, shipping
costs will be the responsibility of the owner.
COPYRIGHT AND TRADEMARKS:
© Copyright 2006 Runco International. This document contains proprietary information protected by copyright, trademark and
other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any mechanical,
electronic or other means, in any form, without prior written permission of the manufacturer.
Reflection, Enhanced GEN3, DHD, Vivix, Virtual Cinema, CineWide, AutoScope, O-Path, CinOptx, LiveLink, CSMS, SuperOnyx
and VirtualWide are trademarks of Runco International.
All other trademarks and registered trademarks used in this document are the property of their respective owners.
Runco International products are manufactured under one or more of the following patents: US. Patent 6755540 and Other
Patents Pending.
iv
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL INFORMATION:
To locate the name and address of the nearest Runco Authorized Service Center, or for additional information about this
Limited Warranty, please call or write:
RUNCO INTERNATIONAL, INC.
Attn: Customer Service Department
2900 Faber Street
Union City, CA 94587
Ph: (510) 324-7777
Fax: (510) 324-9300
Toll Free: (800) 23-RUNCO
RUNCO VIDEO-PRODUCT INFORMATION
RETAIN THIS INFORMATION FOR YOUR RECORDS
_________________________________________________________
Model Purchased
________________________________________
Date
____________________________________________________________________________________________________________
Serial Number
____________________________________________________________________________________________________________
Runco Authorized Dealer Name
____________________________________________________________________________________________________________
Address
____________________________________________
__________________
State/Province
________________________
Postal Code
City
____________________________________________
Phone
_______________________________________________________
Fax
Runco CL-610 Series Owner’s Operating Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions
Thank you for your purchase of this quality Runco video projector! It has been designed to provide you with the quality of video
that is expected in a home theater. For the best performance, please read this manual carefully as it is your guide through the
menus and operation.
WARNING
This symbol is intended to alert the user to the presence of
uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric
shock.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Do not use this equipment near water, outdoors or otherwise exposed to the elements.
5. Clean only with a dry cloth.
6. Do not block any ventilation openings.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
8. Do not defeat the safety feature of the polarized or grounding type plug. A polarized type plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The third prong is provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete
outlet.
9. The 12V trigger only outputs DC 12V signal for triggering. Do not connect to any other power input or output. This could
cause damage to this unit.
10. Only use accessories specified by Runco International.
11. Keep the packing material in case the equipment should ever need to be shipped.
12. Unplug this projector during lightning storms or when it will not be used for an extended period of time.
13. The lamp becomes extremely hot during operation. Allow the projector to cool down for approximately 45 minutes prior to
removing the lamp assembly for replacement. Do not operate lamps beyond the rated lamp life. Excessive operation of
lamps beyond rated life could cause them to explode in rare occasions.
14. Refer all servicing to qualified service personnel. Servicing is required when the projector has been damaged in any way,
objects have fallen or spilled into the projector, the projector has been exposed to rain or moisture, does not operate
normally, or has been dropped.
vi
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1Table of Contents
TWO YEAR LIMITED WARRANTY .................................................................................iii
Safety Precautions .........................................................................................................vi
1. Introduction ...............................................................................................................1
About This Manual .......................................................................................................1
If You Have Comments About This Manual.............................................................1
2. Controls and Functions ............................................................................................5
Front/Side/Top View...............................................................................................5
3. Installation ...............................................................................................................13
Notes on Batteries................................................................................................13
Notes on Remote Control Operation.....................................................................13
Quick Setup ...............................................................................................................14
Installation Type....................................................................................................15
Other Considerations............................................................................................18
Runco CL-610 Series Owner’s Operating Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
RS-232 Controller Connection..............................................................................23
Turning On the Power ................................................................................................25
Adjusting the Picture Orientation ................................................................................25
4. Operation .................................................................................................................29
Selecting an Aspect Ratio ..........................................................................................29
Turning Off the Power ................................................................................................30
Using the On-Screen Menus ......................................................................................30
Picture Adjustment ..............................................................................................32
Set Up..................................................................................................................42
5. Maintenance and Troubleshooting ........................................................................49
viii
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Serial Communications ..........................................................................................53
RS-232 Connection and Port Configuration ...............................................................53
7. Specifications ..........................................................................................................57
CL-610 Dimensions ...................................................................................................59
Runco CL-610 Series Owner’s Operating Manual
ix
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
x
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1List of Figures
2-1. CL-610 Front/Side/Top View........................................................................................5
2-5. CL-610 Remote Control.............................................................................................10
3-1. Estimating Throw Distance.........................................................................................16
3-2. Projector Placement...................................................................................................17
3-3. Folded Optics.............................................................................................................17
3-7. Composite, S-Video and Component Video Connections...........................................22
4-3. Typical Gray Bar Pattern for Adjusting Contrast..........................................................34
Runco CL-610 Series Owner’s Operating Manual
xi
Download from Www.Somanuals.com. All Manuals Search And Download.
List of Figures
Notes:
xii
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Introduction
This Owner’s Manual describes how to install, set up and operate the Runco Reflection
CL-610 family of Digital Light Processing™ Projectors:
1.1
About This Manual
• CL-610
• CL-610LT (Long Throw)
• CL-610/CineWide™
• CL-610LT/CineWide
Throughout this manual, all four projector models are referred to collectively as the
“CL-610.” Except where noted, the features and functions described in this manual are
common to all versions of this product.
Runco has prepared this manual to help home theater installers and end users get the
most out of the CL-610.
Target Audience
Runco has made every effort to ensure that this manual is accurate as of the date it was
printed. However, because of ongoing product improvements and customer feedback, it
If You Have Comments
About This Manual...
Text Conventions: The following conventions are used in this manual, in order to clarify
the information and instructions provided:
Textual and Graphic
Conventions
• Remote and built-in keypad button identifiers are set in upper-case bold type; for
example, “Press EXIT to return to the previous menu.”
• Computer input (commands you type) and output (responses that appear on-screen) is
shown in monospace (fixed-width) type; for example: “To change the aspect ratio to
Letterbox, type x063x <Enter>.”
• All keys with functional names are initial-capped, set in bold type and enclosed in angle
brackets. These keys are the following: <Enter>, <Spacebar>, <Control>,
<Esc>and <Tab>.
• <Enter>indicates that you may press either the RETURN or ENTER key on your
keyboard if it has both keys.
In addition to these conventions, underlining, boldface and/or italics are occasionally used
to highlight important information, as in this example:
A carriage return must be used after each command or string.
Note
Runco CL-610 Series Owner’s Operating Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Graphic Conventions: These symbols appear in numerous places throughout the
manual, to emphasize points that you must keep in mind to avoid problems with your
equipment or injury:
TIPS highlight time-saving short cuts and helpful guidelines for using
certain features.
Tip
NOTES emphasize text with unusual importance or special
significance. They also provide supplemental information.
Note
CAUTIONS alert users that a given action or omitted action can
degrade performance or cause a malfunction.
Caution
WARNINGS appear when a given action or omitted action can result
in damage to the equipment, or possible non-fatal injury to the user.
WARNING
DANGER!
DANGER appears when a given action can cause severe injury or
death.
Use the following table to locate the specific information you need in this manual.
1.2
Using This Manual
If you need...
... Turn to page:
Information about obtaining service
General information about the CL-610 Series DLP
Projectors
Installation instructions
First-time configuration instructions
Advanced configuration instructions
Troubleshooting tips
Specifications for the CL-610 Series DLP Projec-
tors
2
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
The CL-610 Series DLP Projectors offer the astounding picture quality and versatility
heretofore associated with more expensive projectors. Their 1280 x 720 native resolution
DLP light engine incorporates all-new technology for bright, pristine high-definition
images.
1.3
Description, Features
and Benefits
With throw distances of 1.37 – 1.82:1 on the CL-610 and 1.87 – 2.47:1 on the
longer-throw CL-610LT, both units offer the performance and installation flexibility custom
home theater enthusiasts have come to expect from Runco — all at a superb price and
packaged with outstanding build quality.
Advanced Runco Vivix™ digital video processing is engineered into these all-new
projection systems to achieve improved image quality even from standard video sources,
in addition to artifact-free scaling of higher resolution formats.
The CL-610's illumination system incorporates Runco's exclusive Selectable Lamp
Intensity Control™ (SLIC™), which provides two light intensity levels to allow maximum
flexibility for screen size, ambient light conditions, brightness and contrast balance, and
lamp life preservation. It also has a newly-refined cooling system, which increases
efficiency and reduces noise levels.
The CL-610 has been engineered to comply with Imaging Science Foundation™ (ISF)
standards for maximum home theater image quality. Runco's sophisticated parameters
for white balance and color gamut control have also been implemented for precise
balance of gray scale and color.
For uncompromising widescreen reproduction of movies originally filmed in the “scope”
(2.35:1) format, the CL-610 can be equipped with Runco’s patent-pending CineWide™
technology, a combination of software, electronics and high-quality anamorphic optics.
CineWide maintains constant vertical height on the screen just as in a movie theater.
When a viewer transitions from 1.78:1 (16:9) program material to 2.35:1, the image simply
gets wider while full height is maintained.
CineWide requires the use of a 2.35:1 or similar aspect ratio superwide
format screen.
Note
Discrete IR and RS-232 control make custom installation seamless, while discrete source
and aspect ratio selection accommodate any automation control system.
Runco CL-610 Series Owner’s Operating Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Key Features and Benefits
The CL-610 offers these key features and benefits:
➤
• Native Resolution: 1280 x 720 (16:9 Native Aspect Ratio)
• DLP system using high-performance Digital Micromirror Device (DMD)
• 6-segment, 5x color wheel produces wide dynamic range and rich grayscale
• Picture in Picture / Picture by Picture functions allow you to display two inputs on the
screen at the same time
• HDMI Input with High-bandwidth Digital Content Protection (HDCP)
• HDTV Compatible
Parts List
Your CL-610 is shipped with the following items. If any items are missing or damaged,
please contact your Runco dealer or Runco Customer Service at (800) 23RUNCO.
➤
• CL-610 DLP Projector
• Remote Control Unit and two (2), AAA-size batteries
• AC Power Cords (North America, Europe, Asia)
• Source Connection Cables:
• Composite Video
• S-Video
• Component Video
• RGB (DB15HD-to-5 x BNC)
• HDMI to HDMI
• HDMI to DVI
• Warranty information and registration card
• Runco CL-610 Series Owner’s Operating Manual (this document)
Optional Accessories:
• CineWide™ technology (secondary anamorphic lens and motorized mount)
• Ceiling mount kit
4
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Controls and Functions
2.1
CL-610 at a Glance
Front/Side/Top View
Figure 2-1. CL-610 Front/Side/Top View
1. EXHAUST VENT
2. FOCUS RING / ZOOM RING ACCESS
Adjust the size and focus of the image.
3. RUNCO LOGO
The logo can be rotated to match the projector orientation: inverted (ceiling-mounted)
or upright. To rotate the logo, grip it at the sides, pull it away from the projector and
rotate it 180 degrees.
4. TOP IR SENSOR
5. STATUS LEDs
Runco CL-610 Series Owner’s Operating Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6. INTAKE VENT
7. FRONT IR SENSOR
8. PROJECTION LENS
Rear/Side/Bottom View
➤
Figure 2-2. CL-610 Rear/Bottom/Side View
1. CONNECTOR PANEL
2. AC POWER INPUT (100 to 240 VAC)
Connect the CL-610 to power here.
3. AC POWER SWITCH
Disconnects or applies power to the CL-610.
4. CABLE ACCESS DOOR
Open to access connectors.
5. CABLE OPENING
Pass cables through this opening.
6
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. RUNCO LOGO
The logo can be rotated to match the projector orientation: inverted (ceiling-mounted)
or upright. To rotate the logo, grip it at the sides, pull it away from the projector and
rotate it 180 degrees.
7. LAMP MODULE COVER
Remove this cover to access the lamp compartment.
8. FRONT/REAR ADJUSTERS
Use these to adjust the projector height or projection angle.
9. CEILING MOUNT HOLES
Use these to attach the ceiling bracket to the projector.
Figure 2-4 shows the CL-610 lens controls and status indicator LEDs. .
2.2
Lens Controls and
Status Indicators
Figure 2-3. CL-610 Lens Controls and Status Indicators
1. FOCUS RING
Rotate the ring to focus the projected
image.
Focus
2. ZOOM RING
Zoom out
Zoom in
Rotate the ring to adjust the projected
image size.
Runco CL-610 Series Owner’s Operating Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. LAMP LED
Indicates lamp status as follows:
• Off during normal operation
• Red when the lamp has exceeded its usage life or developed a problem
• Flashes red when the fans are not working or the lamp cover is open
4. POWER/STANDBY LED
Indicates power status as follows:
• Orange when the projector is in standby mode
• Flashes orange for 45 seconds after the projector is turned on to indicate that the
lamp is warming up
• Green during normal operation
• Flashes green for 110 seconds after the projector is turned off to indicate that the
lamp is cooling down
5. TEMP LED
Indicates fan status and internal temperature as follows:
• Off during normal operation
• Red when internal temperature is too high
• Flashes red when the fans are not working or the lamp cover is open
Figure 2-4 shows the CL-610 connector panel.
2.3
CL-610 Connector
Panel
Figure 2-4. CL-610 Connector Panel
8
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. S-VIDEO
A standard S-Video input for connecting a DVD player, satellite receiver or Super VHS
(S-VHS) VCR.
2. 12-VOLT (250 mA) TRIGGER OUTPUT (3.5-mm, mini phono jack)
Connection for 12-volt trigger-activated equipment such as retractable screens or
screen masking.
3. COMPOSITE VIDEO INPUT
Standard composite video input for connecting a VCR, laser disc player or other
composite video source.
4. COMP 1 (RCA connectors)
Standard Definition (480i/576i) Component (YPrPb) input. This is the input for
component video from sources such as DVD players.
5. HDMI (Digital)
HDCP-compliant digital video input for connecting a DVD player or HD tuner with a
DVI or HDMI output.
For best results, do not run your DVD player in progressive mode.
Tip
6. COMP 2 / RGB
Five (5) BNCs for connecting either RGB or component (YPbPr) high-definition
television signals. (The CL-610 automatically detects the signal format.)
7. RS-232 CONTROL PORT
A female, RJ-11 connector for interfacing with a PC or home theater
automation/control system.
Runco CL-610 Series Owner’s Operating Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 2-5 shows the CL-610 remote control, and the paragraphs that follow describe its
functionality.
2.4
CL-610 Remote
Control
LIGHT
ON
1
OFF
2
VID
INFO
EXIT
S-VID
COMP1
HDMI
COMP2
3
RGBHD
RVR
ENTER
4
6
MENU
BRT
CONT
COL
TNT
5
7
ISF
NIGHT
ISF
DAY
MEM1
FACT
ANA
16X9
4X3
LBOX
VWIDE
VCINE
CINEMA
1
4
8
2
5
9
3
7
6
0
8
PBP
ACT
PIP
PIP+
PIP-
9
Figure 2-5. CL-610 Remote Control
1. LIGHT
Press to illuminate the buttons.
2. ON / OFF
Use these buttons to turn the projector on or off.
10
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Source Selection Buttons:
VID
Press to select Composite video input as the source.
S-VID (S-Video)
Press to select the S-Video input as the source.
COMP1 (SD Component)
Press to select Component 1 (SD 480i/576i) video input as the source.
COMP2 (HD Component)
Press to select Component 2 (HD 480p/576p/720p/1080i) video input as the source.
RGBHD
Press to select the Component 2 RGB input.
HDMI
Press to select the HDMI input.
4. INFO
Displays active source and aspect ratio information.
Cursor Keys (
,
,
,
)
Use these buttons to select items or settings, adjust settings or switch display
patterns.
RVR
Not applicable to this projector.
EXIT
Press to save menu item setting(s), exit the current menu and return to the previous
one.
ENTER
Press to select a highlighted menu item or confirm a changed setting.
MENU
Press this button to show or hide the on-screen display (OSD) controls.
5. Picture Adjustment Buttons:
BRT (Brightness)
Press to adjust black level.
CONT (Contrast)
Press to adjust white level.
COL (Color)
Press to adjust color intensity.
TNT (Tint)
Press to adjust color hues.
Runco CL-610 Series Owner’s Operating Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Memory Preset Buttons:
MEM1
Press to recall settings for the current input from the “Memory 1” memory preset.
ISF NIGHT
Press to recall settings for the current input from the “ISF Night” memory preset.
ISF DAY
Press to recall settings for the current input from the “ISF Day” memory preset.
FACT
Press to recall the factory-default settings for the current input.
7. Aspect Ratio Selection Buttons
Use these buttons to select an aspect ratio directly, as follows:
ANA 16:9 (Anamorphic)
For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.
4X3 (Standard 4:3)
Scales the input signal to fit 4:3 display mode in the center of the screen.
LBOX (Letterbox)
For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.
VWIDE (VirtualWide)
Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display.
CINEMA
For viewing 2.35:1 source material.
VCINE (CL-610/CineWide and CL-610LT/CineWide only)
Selects the Virtualwide 2.35 aspect ratio, used for viewing 16:9 source material on a
2.35:1 screen.
8. 0 - 9
Use these keys to enter menu passcodes.
9. Picture-In-Picture (PIP) / Picture-By-Picture (PBP) Controls:
PBP
Press to activate PBP mode.
ACT
Press to switch to the active window in PIP or PBP mode.
PIP
Press to activate PIP mode.
PIP+
Press to enlarge the PIP window.
PIP-
Press to shrink the size of the PIP window.
12
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Installation
To install batteries in the remote control, push the
battery cover and slide it off. Install the two AAA
batteries with the correct polarity and then
replace the cover.
3.1
Remote Control
• Make sure that the battery polarities are correct when installing the batteries.
• Do not mix an old battery with a new one or different types of batteries.
Notes on Batteries
• If you will not use the remote control for a long time, remove the batteries to avoid
damage from battery leakage.
• Make sure that there is nothing obstructing the infrared beam between the remote
control and the IR receiver on the projector.
Notes on Remote Control
Operation
• If the effective range of the remote control decreases, or it stops working, replace the
batteries with new ones.
• The remote control may fail to operate if the infrared remote sensor is exposed to bright
sunlight or fluorescent lighting.
• Ambient conditions may possibly impede the operation of the remote control. If this
happens, point the remote control at the projector, and repeat the operation.
• The Ø icon appears on the screen when you press a button for an unavailable function.
Runco CL-610 Series Owner’s Operating Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 3-1 gives a quick overview of the CL-610 installation process. The sections
following this one provide detailed instructions.
3.2
Quick Setup
Installation should be performed by a qualified custom video
installation specialist.
Note
Table 3-1. Installation Overview
For Details, Refer to
page...
Step
Procedure
Choose a location for the projector
Mount the projector
1
2
3
4
Connect signal sources to the CL-610
Connect external controller to RS-232 port (optional)
Connect 12-volt trigger output to retractable screen or
other, +12-volt trigger-activated equipment (optional)
5
Apply power to the projector
6
7
Change the OSD Language (optional)
For rear-screen and/or ceiling-mount installations, select
the proper picture orientation
8
9
Primary lens adjustments: projected image size (zoom) and
focus
Install CineWide anamorphic lens
(CL-610/CineWide and CL-610LT/CineWide only)
10
11
CineWide lens adjustments: position, angle, geometry and
focus
Projector calibration: adjust the following for each input;
save settings when finished:
• Aspect ratio
• Brightness
12
• Contrast
• Color level
• Tint
• Input position
14
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper installation of your projector will ensure the quality of your display. Whether you are
installing a projector temporarily or permanently, you should take the following into
account to ensure your projector performs optimally.
3.3
Installation
Considerations
Choose the installation type that best suits your needs: front or rear screen, floor mount or
Installation Type
Table 3-2. Projector Installation Options
Advantages
Front Screen, Floor Mount Installation
• Shares floor space with audience
Considerations
• Easy to set up
• Can be moved or changed quickly
• Easy to access
Front Screen, Inverted Mount (ceiling) Installation
• Does not take up audience space
• Projector is unobtrusive
• Installation is more permanent
• Projector access is more difficult
• Projector cannot be accidentally moved
Rear Screen, Floor Mount Installation
• Projector is completely hidden
• Projector is easily accessed
• Requires separate room
• Installation cost is usually higher
• Usually good ambient light rejection
Rear Screen, Inverted Mount (ceiling) Installation
• Projector is completely hidden
• Requires separate room
• Usually good ambient light rejection
• Installation cost is usually higher
Rear Screen, Floor Mount with Mirror
• Projector is completely hidden
• Usually good ambient light rejection
• Requires less space behind screen than
other rear screen installations
• Requires separate room
• Installation cost is usually higher
In general, minimize or eliminate light sources directed at the screen. Contrast ratio in your
images will be noticeably reduced if light directly strikes the screen, such as when a shaft
of light from a window or floodlight falls on the image. Images may then appear washed
out and less vibrant.
Ambient Light
Runco CL-610 Series Owner’s Operating Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Throw Distance
Throw distance is the distance measured from the front of the projector to the screen.
This is an important calculation in any projector installation as it determines whether or not
you have enough room to install your projector with a desired screen size and if your
image will be the right size for your screen.
➤
You can quickly estimate the throw distance by taking the width of the screen and
roughly how far back the projector should be positioned from the screen in order to
project a focused image large enough to fill the screen.
Estimating Throw Distance
Throw Distance (TD) = Screen Width (w) x Lens Throw Ratio
Scr
een w
idth (w)
TD
Figure 3-1. Estimating Throw Distance
Table 3-3 lists the throw ratios for the CL-610 Series.
Table 3-3. Throw Ratios for the CL-610 Series
Throw Range in
inches, with
72.6x40.8-inch
(1.78:1) Screen
Throw Range in
inches, with
96x40.8-inch (2.35:1)
Screen
Throw Ratio
with Primary
Lens and
Anamorphic
Lens
Throw Ratio
Projector Model with Primary
Lens Only
Minimum Maximum
Minimum Maximum
CL-610
1.37 - 1.82
1.87 - 2.47
99.46
(n/a)
132.13
179.32
(n/a)
CL-610/CineWide
CL-610LT
1.55 - 1.82
1.87 - 2.47
148.80
(n/a)
174.72
237.12
135.76
CL-610LT/
CineWide
(n/a)
179.52
16
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proper placement of the projector relative to the screen will yield a rectangular,
perfectly-centered image that completely fills the screen.
Vertical and Horizontal
Position
Ideally, the projector should be positioned perpendicular to the screen and in such a way
that the lens center is aligned with either the top or bottom edge of the screen area, and
centered horizontally.
The top of the projected image is even with the lens center when the projector is inverted
(ceiling-mounted). Likewise, the bottom of the projected image is aligned with the lens
Ceiling Installation
Ceiling
Height
Projection Distance
x
Lens Center
Lens Center
Screen
Floor Installation
Screen
Lens Center
Height
Lens Center
x
Projection Distance
Floor
Figure 3-2. Projector Placement
In rear-screen applications where space behind the projector is limited, a mirror may be
mirror must be accurately set. If you are considering this type of installation, contact your
dealer for assistance.
Folded Optics
Screen
Mirror
Figure 3-3. Folded Optics
Runco CL-610 Series Owner’s Operating Manual
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Considerations
Other considerations and tips that can help improve your installation:
➤
• Keep the ambient temperature constant and below 35°C (95°F). Keep the projector
away from heating and/or air conditioning vents. Changes in temperature may cause
drifts in the projector circuitry, which may affect performance.
• Keep the projector away from devices that radiate electromagnetic energy such as
motors and transformers. Common sources of these include slide projectors,
speakers, power amplifiers and elevators.
There are several methods for mounting the projector. Depending on your chosen
installation, one method may be more suitable than another.
3.4
Mounting the CL-610
Floor Mounting (Upright)
In typical front and rear screen installations, the projector can be placed upright on a
secure and level surface such as a table or cart. Carts are useful when moving a projector
during a presentation or from site to site. If possible, lock the wheels when it’s in position
to prevent it from being moved during a presentation.
➤
➤
Ceiling Mounting
(Inverted)
For fixed installations, and for those that want the projector out of sight or have a limited
space for projector and audience, you can invert the CL-610 and suspend it from the
ceiling using a specially-designed ceiling mount fixture.
Use only the Runco-approved ceiling mount kit designed for your
projector. Install the mount kit according to the instructions
Caution
provided with it.
The projector can also be inverted and placed in an enclosure above and behind the
viewing area. Install four feet on the inside bottom surface of the enclosure on which the
projector can rest. A variety of materials can be used for this purpose (for example, rubber
crutch tips or turntable feet).
Adjusting the Projector
Height or Projection Angle
If the screen is significantly higher or lower than the projector, you can also tilt the
projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling
mount.
➤
For a floor installation, turn the four adjustable
feet on the bottom of the projector to adjust
the projector height and/or projection angle.
If you do this, you may need to make
keystone adjustments or vertically shift the
image using the on-screen display (OSD)
controls, to compensate. For detailed
instructions, refer to Using the On-Screen
18
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Proceed as follows to connect the CL-610 to your video sources, external controller(s) – if
present – and AC power.
3.5
Connections to the
CL-610
When connecting your equipment:
• Turn off all equipment before making any connections.
• Use the correct signal cables for each source.
• Ensure that the cables are securely connected. Tighten the thumbscrews on
connectors that have them.
To access the connector panel, press
the door release button so it pops out.
Turn the knob clockwise or
Connector Panel Access
counter-clockwise and pull gently on it
to open the door.
Connect your video sources to the CL-610 as shown and described in the sections that
follow.
Connecting Source
Components to the
CL-610
HDMI-to-HDMI cable; with a DVI source, use the included DVI-to-HDMI cable.
Use the HDMI input whenever possible. This ensures the highest
Tip
video quality because the signal is carried in the digital domain
throughout the entire signal path, from source component output
into the projector.
HDMI or DVI Source
(DVD Player or HD Set Top Box)
Figure 3-4. HDMI/DVI Source Connections
Runco CL-610 Series Owner’s Operating Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
RGB Connections: Connect your personal computer or other RGB source (DVD player
DB15HD-to-5 x BNC cable if your RGB source has a 15-pin, VGA-type connector.
The CL-610 supports the following computer resolutions:
1024x768, 800x600 and 640x480.
Note
Vert Horiz Red Blue Green
Vert Horiz Red Blue Green
DVD Player or
HD Set Top Box
Personal
Computer
Figure 3-5. RGB Connections
20
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Composite/S-Video/Component Video Connections: Use the included cables to
connect your composite, S-Video and SD (480i) component video sources to the CL-610
DTV Source,
DVD Player, VCR,
Satellite Receiver
etc.
Figure 3-7. Composite, S-Video and Component Video Connections
22
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect a PC or home theater control/automation system (if present) to the RS-232 port
straight-through.
RS-232 Controller
Connection
RJ-11 to
D-Sub 9-pin Adapter
(not included)
RJ-11 Male
Yellow
Yellow
Green
Green
5
4
3
2
1
1
2
3
4
9
8
7
6
Black
Red
Black
D-Sub 9-pin female
Red
RS-232 Adapter Wiring
D-Sub 9-pin female
4-pin RJ-11
Function
2
2
3
Transmit Data
Receive Data
Ground
3
5
1, 4
--
1, 4, 6, 7, 8, 9
Not Connected
Figure 3-8. RS-232 Control System Connection
Runco CL-610 Series Owner’s Operating Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting 12-volt
Trigger Output to External
Theater Equipment
If your home theater contains a retractable screen, screen mask or other 12-volt
trigger-activated equipment, use the cable supplied with the CL-610 to connect it to the
➤
S - V I D
S-VID /
3.5-mm
mini plug
to other,
12-volt
trigger-activated equipment
(screen, screen mask etc.)
Black = Ground (Sleeve)
Red = +12V (Tip)
Figure 3-9. Connecting the 12-Volt Trigger Output to Other Equipment
Connecting to AC Power
The CL-610 ships with various
types of AC power cords. Choose
➤
Power
switch
the one that is appropriate to your
locale.
Plug the female end of the power
cord into the AC receptacle on the
rear of the projector (AC 100V ~
240V). Then, connect the other end
to your AC power source.
24
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Turn on your source components.
3.6
Turning On the Power
2. Turn on the main power switch at the rear of the projector. The POWER LED lights
orange. The LAMP and TEMP LEDs light red briefly, then go out.
3. Press the ON button on the remote control to turn
on the CL-610. The POWER LED flashes orange
to indicate that it is warming up.
LIGHT
ON
S-VID
OFF
4. When the projector is ready for use, the POWER
VID
COMP1
HDMI
COMP2
LED lights green.
RGBHD
5. “Searching...” appears on the screen before the
CL-610 identifies the input signal and remains there
until a valid signal is detected.
6. If an incompatible input signal exceeds the range of the projector, a “No signal
supported” message appears on the screen. This message remains on the screen
until you change the input signal.
The CL-610 OSD language is initially set to English, but can also display the menus in
French, Spanish, Italian or German. To change the OSD language:
3.7
Changing the OSD
Language
1. Press MENU.
2. Select Installation from the Main Menu and press ENTER.
3. Select Language from the Installation Menu and press ENTER.
4. Press
or
to highlight the desired language. (The change takes effect
immediately.)
By default, the CL-610 is configured for a “floor/front” installation, in which the projector is
installed upright and in front of the screen. If it is installed behind the screen and/or
mounted on a ceiling, you must change the picture orientation. To do this:
3.8
Adjusting the Picture
Orientation
1. Press MENU on the remote control.
2. Select Installation from the Main Menu and press ENTER.
3. Select Picture Orientation from the Installation Menu and press ENTER.
4. Choose Floor Rear, Ceiling Front or Ceiling Rear to match the installation method.
The CL-610 gives you a great deal of control over the picture size and focus.
3.9
Zoom and Focus
Adjustments
Adjust the projected image size with
the zoom ring on the lens. To focus
the image, rotate the focus ring on
the lens.
Focus
Zoom out
Zoom in
Runco CL-610 Series Owner’s Operating Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
If you are installing a CineWide-equipped projector, proceed as follows to install and
adjust the anamorphic lens.
3.10
Installing and
Adjusting the
CineWide Anamorphic
Lens
It is extremely important that the primary lens is properly
Note
adjusted before you install the anamorphic lens. Ensure that
the image from the primary lens is perfectly centered on the
screen.
are missing or damaged, please contact your Runco dealer or Runco Customer Service at
(800) 23RUNCO.
1
Anamorphic Lens
2
Mounting Bracket (2x)
3
Pitch Adjustment Screw,
4-40 x 5/16" (4x)
4
Washer (4x)
5
Y-Adjustment Screw,
Phillips Pan-Head,
6-32 x 3/8" (4x)
6
Fender Washer (4x)
Figure 3-10. Anamorphic Lens Mounting Assembly - Exploded View
Remove the Projector
Loosen the small Phillips screw (directly below the lens) holding the jewelry in place. Then,
remove the jewelry.
➤
Front Jewelry
Installing the Anamorphic
Lens
1. Use the Pitch Adjustment Screws (item #3) and Washers (item #6) to attach the
Mounting Brackets (item #2) to the Anamorphic Lens (item #1). (Do not fully tighten
the screws yet.)
➤
2. Use the four Y-Adjustment Screws (item #5) and Washers (item #4) to attach the
Anamorphic Lens assembly to the front of the projector. (Again, do not fully tighten
the screws yet.)
26
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Height (Y) Adjustment:
Adjusting the Anamorphic
Lens
1. Project a white field on the screen.
2. Ensure that the four Y-Adjustment Screws are loose enough to allow movement of
the lens assembly.
3. Slowly move the anamorphic lens into place so that there are no shadows on the top
or bottom of the screen:
Too Low
Correct position
Too High
4. When the height is properly set, tighten the Y-Adjustment Screws to secure the lens in
place.
Adjusting the Pitch (Angle): Next, angle the lens to even out any top-to-bottom
pincushion distortion. To do this, loosen the Pitch Adjustment Screws on either side of the
lens to allow it to pivot freely. Then, adjust the anamorphic lens angle so that the projected
image is rectangular:
Correct Lens Angle
Incorrect Lens Angle
The anamorphic lens will almost always be angled with respect to the projector; this is
normal.
Once the proper lens angle has been set, firmly tighten the Pitch Adjustment Screws to
secure the lens in place.
Runco CL-610 Series Owner’s Operating Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
To avoid clipping the corners of the image, position the anamorphic
lens as close as possible to the primary lens.
Tip
There may be some pincushion distortion even after the lens is
properly adjusted, especially at shorter throw distances. If this is the
case, Runco recommends that you slightly over-scan the image
into the screen frame area to mask the distortion.
Note
28
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Operation
• Press the MEM1 button on the remote control
to recall settings for the current input from the
“Memory 1” memory preset.
4.1
ISF
NIGHT
ISF
DAY
MEM1
FACT
Selecting Video
Memory
• Press ISF NT (Night) to recall settings for the current input from the “ISF Night”
memory preset.
• Press ISF DAY to recall settings for the current input from the “ISF Day” memory
preset.
Press FACT to recall the factory-default settings for the current input. An on-screen
confirmation message appears. Press FACT again to confirm.
Use these buttons to select the appropriate aspect
4.2
ANA
4X3
LBOX
VWIDE
VCINE
16X9
ratio for the type of program material being viewed.
For more information on aspect ratios, refer to Table
4-1.
Selecting an Aspect
Ratio
CINEMA
1
2
When you turn on the CL-610, it switches to the last
selected input and looks for a valid signal.
4.3
VID
S-VID
COMP1
HDMI
COMP2
Selecting An Input
Source
RGBHD
Use these buttons on the remote control to select an
input source directly.
For PIP and PBP purposes, there are two groups of
inputs separated by their display modes:
4.4
Using
Picture-In-Picture and
Picture-By-Picture
(PIP/PBP)
PBP
ACT
PIP
PIP+
PIP-
• Video (SD) group: Video, S-Video and
Component 1 inputs.
• Graphic (HD) group: HDMI and Component 2/RGB inputs.
PIP and PBP show one input from the Graphic group within or beside one input from the
Video group respectively.
• Press PBP to enable the PBP function. Press PBP again to switch the screens left to
right. Press PBP again to turn PBP off.
• Press ACTIVE to switch to the active window. (You can only switch inputs in the active
window.)
• Press PIP to enable the PIP function. Press PIP again to switch the main window.
Press PIP again to turn PIP off.
• To adjust the size of the PIP window, press PIP+ or PIP-.
• Adjust the position of the PIP window with the arrow buttons (
,
,
,
).
Runco CL-610 Series Owner’s Operating Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Press the OFF button to turn off the projector.
4.5
Turning Off the Power
2. The POWER LED blinks green and the fans will
speed up for a quick cool-down. The projector will
not accept any commands during the cool-down
period.
LIGHT
VID
ON
S-VID
OFF
COMP1
HDMI
COMP2
RGBHD
3. After approximately three minutes, the fans will
stop running and the POWER LED lights solid
orange.
4. You can turn the projector back on after approximately two minutes.
• Press the MENU button on the remote control to display the Main Menu. To select a
4.6
menu item, use the UP and DOWN buttons on the remote control to highlight it. Press
Using the On-Screen
Menus
ENTER or
to confirm your selection.
• Use the arrow buttons to select menu items or change settings.
• Press EXIT to return to the previous menu.
• Press MENU to turn off the OSD menu. (When the Main Menu is displayed, pressing
EXIT also turns off the menu.)
on the selected input source and signal characteristics, some menu options may not be
available.
30
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Brightness
Contrast
Color
0 ... 60
Reset Image Settings
Sleep Timer
Yes / No
0 ... 32
0, 10, 20, 30 ... 180 minutes
(read only)
0 ... 64
Lamp Hours
Video
S-Video
Component1
Tint
0 ... 30
OSD Timer
0, 3, 6, 9 ... 60 seconds
Horizontal
Sharpness
Filter
-14 ... 0 ... +20
0, 1, 2 or 3
OSD Position
Vertical
0, 1 (5400 K), 2 (6500K), 3
(8500 K), 4 or 5 (Custom)
Auto
Component2 Color Temperature
Frequency
0, +1, +2, +3 ... +17
PC & HD Adjust (480p
and higher-res. signals
only)
RGB-HD
HDMI
Standard, NTSC, HDTV or
PAL
Phase
0, +1, +2, +3 ... +31
-30, -29 ... 0 ... +29, +30
-28, -27 ... 0 ... +29, +30
On / Off
ICC Selection
H. Position
Option
Store Image Settings
Memory 1
V. Position
Restore Image
Settings
Memory 1, ISF Night or ISF
Day
PIP/PBP Enable
PIP Off
Anamorphic (16:9)
Standard (4:3)
Letterbox
PIP Set Up
PBP Set Up
Graphic in Video
Video in Graphic
PBP Off
PIP/PBP Set Up
(not available when used
with the SDC-1)
Virtual Wide
Aspect Ratio
Graphic by Video
Video by Graphic
Cinema
(available only on CL-610
projectors equipped with
the CineWide option)
DNR
0, +1, +2, +3 ... +15
Gamma
Virtual Cinema
English, French, Spanish,
German or Italian
Gain
Red / Green / Blue
Language
White Balance
Offset
Floor Front, Floor Rear,
Ceiling Front or Ceiling
Rear
Store Color Temp. 4
Store Color Temp. 5
Picture Orientation
Installation
2.8, 2.5, 2.2, 1.0,
RUNCO Enhance 1,
RUNCO Enhance 2 or ISF
Day
Keystone Adjust
-14, -13 ... 0 ... +13, +14
Blue or White
Gamma Selection
Background Color
RS-232 Baud Rate
Blue Image
9600, 38400 or 115200
On / Off
H Enhance
V Enhance
Chroma Enhance
H Threshold
V Threshold
Chroma Threshold
Total
SD Enhance
0, +1, +2, +3 ... +127
0, +1, +2, +3 ... +15
Set Up
Image Over Scan
Horizontal
Vertical
Horizontal
Image Shift
-30, -29, ... 0 ... +29, +30
Vertical
Horizontal
Amplitude Adjust
-60, -59 ... 0 ... +59, +60
(CineWide versions only)
Vertical
Horizontal Masking
Video Black Level
Lamp Power
0, +1, +2, +3 ... +100
0 IRE or 7.5 IRE
250W or 200W
Primary
Remote Control
Secondary
Yes / No
Reset Lamp Timer
Auto Normal,
Auto Hi. Altitude or Manual
Mode
Fan Control
Fan Speed (Manual Mode)
Return to User OSD
Reset Picture Adjust
Yes / No
Brightness, Contrast, Color
etc.
Picture Adjust
White Balance
(see above)
(see above)
Gamma, Gain, Offset etc.
2.8, 2.5, 2.2, 1.0,
RUNCO Enhance 1,
RUNCO Enhance 2 or ISF
Day
Gamma Selection
ISF
Calibration
Blue Image
ICC Adjust
On / Off
R / G / B / Y / C / M
Intensity / Sat. / Hue
NTSC / HDTV / PAL
Memory 1, ISF Night or
ISF Day
Store Settings
Splash Screen Timer
ISF Enable
+5, +6, +7 ... +60 seconds
On / Off
Return to User OSD
Figure 4-1. CL-610 OSD Menu Structure
Runco CL-610 Series Owner’s Operating Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu
The Main Menu is the starting point for accessing all projector functions.
➤
(The Set Up and ISF Calibration menus are hidden and not accessible until you enter a
passcode.)
Runco CL-610
Video
S-Video
>
The active source is indicated by an arrow (>) to its left; in the example at left, Video is the
active source. To select a different source, use the or button to highlight it and press
Component1
Component2
RGB-HD
ENTER or
.
HDMI
- - - - - - - - - - - - - - - - -
Aspect Ratio
Installation
Option
Set Up
ISF Calibration
Picture Adjustment
Use the controls in the Adjustment Menu to calibrate your CL-610 for optimum picture
quality. To access the Adjustment menu, press MENU, highlight the active source and
➤
press ENTER or
.
Adjustment
Brightness
To adjust a setting, use the
or
button to highlight it and press ENTER. Use the
Contrast
or button to change the setting. When finished, press EXIT.
Color
The CL-610 has been designed to incorporate setup and calibration standards
established by the Imaging Science Foundation (ISF). The ISF has developed carefully
crafted, industry-recognized standards for optimal video performance and has
implemented a training program for technicians and installers to use these standards to
obtain optimal picture quality from Runco video display devices. Accordingly, Runco
recommends that setup and calibration be performed by an ISF certified installation
technician.
Tint
Sharpness
Filter
Color Temperature
ICC Selection
Store Image Settings
Restore Image Settings
All signal types require separate processing. Therefore, you need to calibrate each input
separately.
When you change a picture quality setting, save the change to a
Note
preset afterwards. Otherwise, the change will be lost when a
different input is selected. (Picture quality settings are saved for
each input and resolution separately.) For information about saving
32
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Although it may be possible to obtain satisfactory picture quality using the naked eye and
regular program material, Runco recommends using the following calibration tools for best
results:
• External test pattern source -- Ovation Multimedia, Digital Video Essentials or AVIA test
DVD or equivalent.
• A blue filter (provided with many test DVDs), for color level and tint adjustments.
Connect your test pattern source to the input that you are calibrating and proceed as
follows. Perform the adjustments in the order listed here.
Brightness: On your external test pattern source, select a PLUGE pattern. (PLUGE is an
pattern.
Below Black
Above Black
Figure 4-2. Typical PLUGE Pattern for Adjusting Brightness
PLUGE patterns vary but generally consist of some combination of black, white and gray
areas against a black background. The example above includes two vertical bars and four
shaded boxes.
Select Brightness from the Adjustment menu and press ENTER. Adjust the brightness so
that:
• The darkest black bars disappear into the background.
• The dark gray areas are barely visible.
• The lighter gray areas are clearly visible.
• The white areas are a comfortable level of true white.
• The image contains only black, gray and white (no color).
Runco CL-610 Series Owner’s Operating Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the
Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast from the Adjustment menu and press ENTER. Adjust the contrast to a
point just below which the white rectangle starts to increase in size.
Brightness and contrast controls are interactive. A change to one
may require a subtle change to the other in order to achieve the
optimum setting.
Note
Color Saturation: On your external test pattern source, select a color bar pattern like the
Figure 4-4. Typical Color Bar Pattern for Adjusting Color Saturation and Tint
34
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Select Color from the Adjustment menu and press ENTER. While looking at the color bar
pattern through a blue filter, adjust the color saturation level until the outermost (gray and
blue) color bars appear to be a single shade of blue:
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image.
When tint is decreased, the image appears redder; when it is increased the image
appears greener. To set the tint, select Tint from the Adjustment menu and press ENTER.
While looking at the color bar pattern through a blue filter, adjust the tint level until the cyan
and magenta color bars (on either side of the green bar) appear to be a single shade of
blue.
Like the brightness and contrast controls, the color and tint controls
are interactive. A change to one may require a subtle change to the
other in order to achieve the optimum setting.
Note
Runco CL-610 Series Owner’s Operating Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust
sharpness, select Sharpness from the Adjustment menu and press ENTER. On your
needed, looking for white edges around the transitions from black to gray and
differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness
setting to eliminate them.
Figure 4-5. Typical Test Pattern for Adjusting Sharpness
The Sharpness setting has no effect if the Sharpness Filter (see
below) is set to 0.
Note
Filter: The Filter setting controls the behavior of the Sharpness control. The available
settings depend on the vertical resolution of the input signal, as follows:
• With a 480i signal, you can apply the sharpness control to either the input signal (1),
the output signal (2), both (3) or neither (0).
• With a 480p or higher-resolution signal, the sharpness control is applied only to the
output signal and only when you set the Sharpness Filter to “on” (1).
36
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Color Temperature: The CL-610 has six memory settings for Color Temperature. Four
of these settings are factory set to default as follows:
Color Temperature
• 0 -- Original lamp color temperature
• 1 -- 5400 kelvins
• 2 -- 6500 kelvins
• 3 -- 8500 kelvins
• 4 -- Custom
2 -
+
• 5 -- Custom
Custom 4 and 5 memory are installer-adjustable and can be used to create custom
settings. There are nine adjustable “white balance” parameters available for the Custom 4
and 5 settings (three each for red, green and blue). These are described later in this
You must enter a passcode in order to enter the Set Up menu.
Note
ICC Selection: Use the ICC Selection menu to select the color space that is appropriate
for the source signal, to achieve optimal color balance.
The International Color Consortium (ICC) is a group of imaging
product vendors that promotes and develops cross-platform,
vendor-neutral color measurement and management standards.
Note
If you select NTSC, HDTV or PAL, you can make further adjustments to individual color
space characteristics in the ICC Adjust sub-menu under the ISF Calibration menu,
described later in this section. (The Standard color space is factory-set and not
adjustable.)
Store Image Settings: Once the desired adjustments have been entered, select Store
Image Settings to save these settings into the “Memory 1” memory location.
Restore Image Settings: To recall stored custom image quality settings, select Restore
Image Settings and choose “Memory 1,” “ISF Night” or “ISF Day.”
To change the aspect ratio (size and shape) of the projected image, select Aspect Ratio
from the Main Menu and press ENTER. Select the appropriate aspect ratio for your
Aspect Ratio
Aspect Ratio
Anamorphic (16:9)
Standard (4:3)
Letterbox
When you change the aspect ratio, save the change to a preset
afterwards. Otherwise, the change will be lost when a different
Note
input is selected. (The aspect ratio is saved for each input and
resolution separately.)
Virtual Wide
Cinema
Virtual Cinema
Runco CL-610 Series Owner’s Operating Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings
Remote
Aspect Ratio
Control
Key
Description
Anamorphic
ANA
Select Anamorphic to view
16:9 DVDs and HDTV
programs in their native
aspect ratio. 4:3 images are
stretched horizontally to fit a
16:9 screen.
16:9 Image on
16:9 Screen
4:3 Image on
16:9 Screen
Standard 4:3
4X3
Standard 4:3 scales the
input signal to fit in the
center of the 16:9 screen.
4:3 is the aspect ratio used
by computer monitors,
standard television
Active Image
Area (4:3)
programming and most
VHS video cassettes.
Letterbox
LBOX
In Letterbox mode, the
image is stretched vertically;
the top and bottom
portions are “blanked off.”
Letterbox is best suited for
viewing LaserDisc movies
or non-anamorphic DVDs
on a 16:9 screen.
Letterbox Image on
16:9 Screen
VirtualWide
VWIDE
VirtualWide scales a 4:3
image NON-linearly (more
on the sides than in the
center) to fit a 16:9 screen.
38
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 4-1. Aspect Ratio Settings (continued)
Remote
Aspect Ratio
Control
Key
Description
Cinema
CINEMA
Select Cinema to view 2.35
source material in its native
aspect ratio.
With a 16:9 screen and a
non-CineWide projector (no
anamorphic lens), the upper
and lower portions of the
screen are masked, but the
geometry of the active
2.35:1 Image on
16:9 Screen
(without CineWide)
image area is unchanged.
With a 2.35:1 screen and a
CineWide-equipped
projector, the projector
enlarges the 2.35:1 image
so that the active image
area fills the 16:9 chip
2.35:1 Image on
2.35:1 Screen
(with CineWide)
surface, eliminating the
black bars. The secondary
anamorphic lens then
vertically compresses the
image to fit a 2.35:1 screen.
Virtual Cinema
VCINE
A 16:9 image is scaled
NON-linearly (more on the
sides than in the center) to
fit a 2.35:1 screen.
2.35:1 Screen
16:9 Image on
Virtual Cinema is available
only on the
CL-610/CineWide and
CL-610LT/CineWide.
16:9 Image on
2.35:1 Screen with
Virtual Cinema
Runco CL-610 Series Owner’s Operating Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
To access the Installation adjustments, press MENU, then press the
highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears.
or
button to
➤
Press EXIT to return to the previous menu or press MENU to close all menus.
Installation
Language
Picture Orientation
Keystone Adjust
Background Color
RS-232 Baud Rate
Blue Image
When you change a setting in the Installation menu, the change
takes effect immediately; you do not need to press ENTER
afterwards. (Press EXIT to return to the previous menu or MENU
to exit.)
Note
Language: Press the
or
button to select from the available languages: English,
French, Spanish, German and Italian.
Picture Orientation: Press the or button to change the orientation of the projected
image. The CL-610 can be installed on a ceiling or in a rear-screen configuration with one
or more mirrors. There are four settings: Floor Front, Ceiling Front, Floor Rear and Ceiling
Rear.
Keystone Adjust: To correct distortion resulting from the angle of projection, select
Keystone Adjust and use the
or
button to make the image rectangular.
Runco recommends that the keystone feature not be used unless
absolutely necessary, as it may cause artifacts in the image.
Tip
Background Color: Press the
or
button to select the image Background Color
(blue or white). The Background Color appears when no incoming signal is present.
RS-232 Baud Rate: Press the or button to select the projector’s RS-232 Baud
Rate. This function is used to change the transfer rate of the RS-232 connection. (This
setting must match the data rate of the device connected to the RS-232 input.)
Blue Image: Press the
or
button to turn the Blue Image Off or On. This feature
removes all red and green color information from the image (simulating a blue filter), and is
useful for color-calibrating the projector or other video components.
Option
To access the Option adjustments, press MENU, then press the
highlight Option and press ENTER. The Installation sub-menu will then appear (see
or
button to
➤
above). Press EXIT to return to the previous menu or press MENU to close all menus.
Option
Reset Image Settings
Sleep Timer
Reset Image Settings: To restore the default image settings for the current input source
ONLY, press the
button to highlight “Yes,” then press ENTER.
Lamp Hours
OSD Timer
Sleep Timer: The Sleep Timer automatically puts the projector into standby mode after
the amount of time you specify here. (A warning appears on-screen one minute before this
is to occur.)
OSD Position
PC & HD Adjust
PIP/PBP Set Up
DNR
Use the
or
button to set the timer for anywhere from 10 minutes to 3 hours, in
10-minute increments. To disable the Sleep Timer, set it to 0.
Lamp Hours: To find out how long the projector lamp has been in use, select Lamp
Hours and press ENTER.
OSD Timer: Use the
or
button to set the OSD Timer. This timer controls how long
the menus remain on-screen after selecting them. Select from 0 to 60 seconds, in
3-second increments. When you set the OSD to 0, the menus remain on-screen until you
hide them by pressing MENU.
40
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
To adjust the horizontal and vertical position of the OSD, select OSD Position and press
ENTER. Then, press the or button to select Horizontal or Vertical and use the
or button to adjust.
PC & HD Adjust: Use the settings in the PC & HD Adjust menu to fine-tune 480p and
higher-resolution signals for optimum picture quality.
• Auto: Adjusts the phase, frequency and position automatically.
• Freq. Adjusts the frequency of the signal.
• Phase: Adjust the phase if the image (usually from an RGB source) shows shimmer or
“noise.” Pixel phase adjusts the phase of the pixel sampling clock relative to the
incoming signal. The effect of this control is similar to that of a tracking control on a
VCR.
For best results, use a good test pattern such as a smooth gray consisting of a clear
pattern of black and white pixels, or a similar “half on, half off” graphic image. (You may
find that you can stabilize the image at more than one point. Use either setting in this
case.)
• H. Pos.: Adjusts the horizontal position of the image.
• V. Pos.: Adjusts the vertical position of the image.
To adjust the image position with a 480i source, use the Image
Note
PIP/PBP Set Up: Select PIP/PBP Set Up from the Option menu to change the PIP/PBP
settings.
• PIP/PBP Enable: Press the
ENTER. Press the or
• PIP Set Up: Press the or
the or
ENTER.
• PBP Set Up: Press the
or
button to select PIP/PBP Enable, then press
button to select Off or On, then press ENTER.
button to select PIP Set Up, then press ENTER. Press
button to select PIP Off, Graphic in Video or Video in Graphic, then press
or
button arrows to select PBP Set Up, then press
ENTER. Press the
or
button to select PBP Off, Graphic by Video or Video by
Graphic, then press ENTER.
DNR: Use the
or
button to adjust the Digital Noise Reduction (DNR). DNR is useful
for clearing up noisy images from interlaced SD sources. Adjust as desired, keeping in
mind that reducing noise (which reduces high frequencies) may also soften the image.
Runco CL-610 Series Owner’s Operating Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Set Up
To access advanced picture quality adjustments, use the up- or down-arrow keys to
highlight Set Up and press ENTER. Use the number buttons on the remote to enter the
Set Up menu passcode when prompted and press ENTER again. Then, press MENU on
the remote control.
➤
Set Up
White Balance
Gamma Selection
SD Enhance
You only need to enter the Set Up menu passcode the first time
you select that menu after turning on the projector.
Note
Image Over Scan
Image Shift
Amplitude Adjust
Horizontal Masking
Video Black Level
Lamp Power
White Balance: To remove any trace of color from the white areas of the projected
image, choose White Balance from the Set Up menu and press ENTER.
• Gamma: “Gamma” is a global setting that determines how gray shades are displayed
between minimum input (black) and maximum input (white) for all signals. A good
gamma setting helps to optimize blacks and whites while ensuring smooth transitions
for the “in-between” values utilized in other grays. Unlike “Brightness” and “Contrast”
controls, the overall tone of your images can be lightened or darkened without
changing the extremes and all images will be more vibrant while still showing good
detail in dark areas.
Remote Control
Reset Lamp Timer
Fan Control
Return to User OSD
In all but the most unusual situations, the appropriate “Gamma Selection” (see below)
will produce accurate colors and a satisfying contrast level. However, it is sometimes
necessary to adjust the red, blue and green gamma curves individually. To do this,
select Gamma from the White Balance sub-menu and use the left- and right-arrow
buttons to manipulate the on-screen slidebars.
• Gain: Use the Gain controls to correct color imbalances in the bright areas of the
image. A good way to do this is to use a test pattern consisting mostly of solid white
areas, such as an 80 IRE “window” pattern. If the white areas contain traces of red,
green or blue, decrease the Gain for that color.
• Offset: Use the Offset controls in the White Balance sub-menu to correct color
imbalances in the dark areas of the image. A good way to do this is to use a test
pattern consisting mostly of dark gray areas, such as a 30 IRE “window” pattern. If the
gray areas contain traces of red, green or blue, decrease the Offset for that color.
• Store Color Temp.4/Store Color Temp.5: When you are finished adjusting the
Gamma, Gain and Offset, select Store Color Temp.4 or Store Color Temp.5 to store
your settings. To recall them, set the Color Temperature to +4 or +5 in the Image
Gamma Selection: The normal gamma setting of 2.2 is correct for almost all signals and
conditions. If excess ambient light washes out the image and it becomes difficult or
impossible to see details in dark areas, lower the gamma setting to compensate. This will
improve contrast while maintaining good details for blacks. Conversely, if the image is
washed out and unnatural, with excessive detail in black areas, increase the setting.
Again, good gamma improves contrast while maintaining good details for blacks and
whites.
42
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
SD Enhance: The SD Enhance menu gives you options for improving the quality of
standard-definition, 480i images. (For 480p and higher-definition images, the controls in
this menu are disabled.) Keep in mind that these controls add frequencies that are not
present in the original signal, and may make images appear “noisy” if misused.
• H Enhance/V Enhance: These controls can improve the apparent horizontal and/or
vertical resolution of the image.
• Chroma Enhance: This control adds chroma (color information) to the input signal
and can make colors appear more vibrant and saturated.
• H Threshold/V Threshold/Chroma Threshold: Set these to +11 or higher to
activate the enhancement controls described above. Generally, the higher the
threshold, the more noticeable the enhancements you make will be.
Image Over Scan: Image Over Scan pushes the outside edge of the active picture area
of the video signal out beyond the edge of the display area.
Some television programs are produced based on the assumption that older television
sets may not display the outer edges of the broadcast picture area. Over scan effectively
trims away these inactive, outer edges and enlarges the remaining portion of the image to
fill the display area.
Use the on-screen slidebar to select the desired amount of over scan.
For HDTV, DVDs and other video sources, Image Over Scan is generally not necessary or
desirable.
Image Shift: The Image Shift menu allows you to precisely center the image on the
screen. (These controls are available only with a 480i source signal.)
• Horizontal: This control moves the image right or left within the area of available pixels.
• Vertical: This option moves the image up or down within the area of available pixels.
1. To adjust the image position with a 480p or higher-resolution
Note
2. The values shown represent where the approximate center of the
image lies in relation to the total number of pixels available
horizontally or vertically. This varies widely according to the
signal; watch the image while adjusting.
Amplitude Adjust: The Amplitude Adjust menu allows you to fine-tune the
currently-selected image aspect ratio by stretching it horizontally or vertically, in small
increments. This can be useful if your projector is equipped with an anamorphic lens.
The Horizontal control adjusts the image width while keeping the height constant.
Similarly, the Vertical control adjusts the image height while keeping the width constant.
Horizontal Masking (CL-610/CineWide and CL-610LT/CineWide only): To achieve
the proper image geometry with the secondary anamorphic lens, select Horizontal
Masking from the Set Up menu. Then, use the or button to change the native aspect
ratio of the display, in small increments.
Runco CL-610 Series Owner’s Operating Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Video Black Level: This control compensates for incoming elevated black levels present
in certain video signals, and ensures that blacks in the display are neither “crushed”
(where dark grays appear black) nor excessively elevated (where blacks appear dark
gray). By default, the projector automatically determines the best setting according to the
type of incoming video signal:
• 0 IRE: Used for DVD output with “enhanced black,” SECAM, most PAL standards and
Japanese NTSC.
• 7.5 IRE: Used for most NTSC video signals.
For some types of video, you may want to override the setting. Generally, if black appears
crushed when brightness = 30, choose “0 IRE.” If black appears excessively elevated, use
“7.5 IRE.”
Lamp Power: Select Lamp Power from the Set Up Menu to adjust the lamp output level.
You can choose to run the lamp as bright as possible (250W; this is the default setting) or
you can choose the lower (200W) setting. Generally, lower lamp output can prolong the
life of the lamp, but decreases brightness.
Remote Control: The Remote Control menu shows you the primary and secondary
infrared (IR) codes to which the CL-610 will respond. The Primary IR code is permanently
set to +20. The secondary IR code is also +20.
You can change the secondary IR code if either:
• Another device in the theater (a DVD player, for example) is responding to commands
from the CL-810 remote control in ways that are unpredictable or undesirable.
• You have multiple CL-610 projectors and want to control them independently, as
opposed to broadcasting commands from a single remote to all of them. In this
scenario, you can use multiple remotes programmed to use different IR codes. Or, you
can use a single remote and change the IR code as needed to address a specific
projector.
When you change the secondary IR code, the remote sends that code instead of the
primary IR code.
The Remote Control menu is read-only and need not be visible in
order to change the secondary IR code.
Note
To simultaneously change the secondary IR code and synchronize that remote with a
projector, point the remote at the projector, then press and hold and simultaneously
for five seconds. The Remote Control edit window, shown at right, appears. Type a new,
two-digit code.
The procedure for changing the secondary IR code on the remote only is the same,
except that you point the remote away from the projector.
44
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
on page 49), you should also reset the lamp timer. To do this, select Reset Lamp Timer
from the Set Up menu. Press the right-arrow key on the remote to highlight “Yes,” then
press ENTER to confirm the reset.
Reset the Lamp Timer ONLY after you replace the lamp. Otherwise,
the reported “Lamp Hours” will be inaccurate.
Note
Do not exceed the recommended lamp life of 2000 hours. An old
lamp becomes increasingly fragile and prone to sudden failure.
WARNING
projector’s cooling fan.
• Mode: In most cases, the default Fan Control Mode (Auto Normal) will maintain the
correct operating temperature. If the lamp frequently turns off due to overheating, or in
certain high-altitude operating environments, you may need to change this setting to
Auto Hi. Altitude or Manual.
• Fan Speed: If you set the Fan Mode to Manual, select Fan Speed and use the
on-screen slidebar to adjust the speed.
After changing either of these settings, press EXIT to return to the previous menu.
Return to User OSD: To exit the Set Up menu, use the up- or down-arrow keys to
highlight Return to User OSD and press ENTER.
To return to the Set Up menu, select it from the Main Menu, press ENTER twice, then
press MENU on the remote control. (You do not need to re-enter the passcode.)
Runco CL-610 Series Owner’s Operating Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
To access the ISF Calibration menu, select ISF Calibration from the Main Menu and press
ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu
passcode when prompted and press ENTER again. Then, press MENU on the remote
control.
➤
ISF Calibration
This menu should be used by ISF-certified technicians only.
Note
Reset Picture Adjust: To restore the ISF default image settings for the current input
source ONLY, press the
button to highlight “Yes” then press ENTER.
PAL color space characteristics. To do this, select the color space to modify. Then, select
a component color (Red, Green, Blue, Yellow, Cyan or Magenta).
For each component color, you can adjust the following:
• Intensity: This slidebar adjusts the intensity – also known as luminance – of a given
color.
• Sat. This slidebar adjusts the color saturation level – the amount of that color in a video
image. Lower settings produce less saturated colors; a setting of “0” removes that
color from the image entirely. If the saturation is too high, that color will be
overpowering and unrealistic.
• Hue: This slidebar adjusts the red/green color hue for true color reproduction of video
signals. For best results, adjust tint while displaying an external color bars test pattern
When you have finished customizing the color space, select Store Setting and press
ENTER.
46
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Store Settings: For each input, the CL-610 lets you store image quality settings as
presets that you can recall at a later time. You can create up to three presets per input
and resolution.
When you change a setting, save the change to a preset
Note
afterwards. Otherwise, the change will be lost when a different
input is selected. (Most settings are saved for each input and
resolution separately.)
To store image quality settings to a preset:
3. Use the
or
button to set the color temperature to “4” or “5.” Make a note of
your selection.
4. Press EXIT.
6. Select White Balance from the ISF Calibration menu. Adjust the grayscale as required
(depending on your selection in Step 3) and press ENTER.
8. From the ISF Calibration menu, select Save ISF Settings and choose “Save ISF Night”
to store your settings.
9. Repeat Steps 1 through 8 for the “Save ISF Day” preset.
The first time you perform this procedure, store the current white
Tip
balance settings in both color temperatures (4 and 5). This will give
you a convenient starting point for color temperature 5, should you
wish to use it for the other preset.
“Memory 1,” “ISF Night” or “ISF Day.” Or, simply use the corresponding buttons on the
remote control.
controls how long the startup (ISF and Runco logo) image stays on-screen after you turn
on the projector. Select from 5 to 60 seconds, in one-second increments. When finished,
press EXIT.
ISF logo on the CL-610 splash screen upon power-up.
You can personalize the CL-610 splash screen with the projector owner’s name and/or
the installer’s name. For instructions, refer to Appendix A.
Return to User OSD: To exit the ISF Calibration menu, use the up- or down-arrow keys
To return to the ISF Calibration menu, select it from the Main Menu, press ENTER twice,
then press MENU on the remote control. (You do not need to re-enter the passcode.)
Runco CL-610 Series Owner’s Operating Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
48
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
5Maintenance and Troubleshooting
The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or
sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to
obtain a replacement lamp.
5.1
Lamp Replacement
1. Turn off the projector and unplug the power cord.
Allow the projector to cool down for
approximately 45 minutes prior to removing
the lamp assembly for replacement.
2. Remove the two screws from the lamp cover.
3. Remove the lamp cover.
4. Remove the two lamp assembly mounting screws.
5. Grasp the lamp assembly handle and pull gently,
removing the lamp module from the projector
housing.
6. Install the new lamp module and replace the two
screws you removed in Step 4.
7. Replace the lamp cover at the top first and secure it
Runco CL-610 Series Owner’s Operating Manual
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1 provides some general guidelines for troubleshooting problems you may
encounter with the CL-610. If the suggested solutions fail to resolve the problem or if you
encounter an issue not described here, please contact Runco Technical Support.
5.2
Troubleshooting Tips
Table 5-1. Troubleshooting Chart
Symptom
Possible Cause(s)
Solution
The projector does not turn
on.
• The CL-610 is not plugged
in or the AC outlet is not
active.
• Ensure that the CL-610 is
plugged in and that the AC
outlet is active.
• The main power switch (at
the rear of the projector) is
off.
• Turn on the power switch.
• Lamp cover is not securely
attached.
• Securely attach the lamp
cover.
The projector does not turn
back on after it was powered
off.
• The projector will not turn
on for two minutes after
power-off, to protect the
lamp.
• Wait until the CL-610
completes its cool-down
(POWER LED lights solid
orange).
The remote control does not
work correctly.
• The batteries have run out.
• Replace the batteries.
The projector is on and OSD
menus appear, but there is no
video image on-screen.
• Incorrect source selection.
• Source component is not
turned on.
• Select the correct source.
• Turn on the source.
• Source component is
connected incorrectly or
not at all.
• Check cable connection
from source component to
projector.
A projected image from a
DVD is split or otherwise
scrambled.
• DVD player is connected
to the Component input
and set to progressive
scan mode.
• Turn off progressive scan
on the DVD player.
Image is blurred.
• The lens is not correctly
focused.
• Adjust the focus by turning
the focus ring.
Image is too bright and/or
lacks definition in the bright
areas of the image.
• Contrast is set too high.
• Lower the contrast setting.
Image appears “washed out”
and/or dark areas appear too
bright.
• Brightness is set too high.
• Lower the brightness
setting.
Colors in the image are
swapped; for example, reds
appear blue or vice versa.
• The Red/Pr, Green/Y or
Blue/Pb outputs from the
source are connected to
the wrong inputs on the
CL-610.
• Ensure that the source
outputs are connected to
the correct CL-610 input.
TEMP and LAMP LEDs are
both flashing red.
• The lamp cover is open.
• Fans are not working
properly.
• Close the lamp cover.
• Please contact your Runco
dealer for assistance.
50
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 5-1. Troubleshooting Chart (continued)
Symptom
Possible Cause(s)
Solution
LAMP LED lights solid red.
• The lamp has failed or
exceeded its usage life.
• Replace the lamp with a
new one.
TEMP LED lights solid red.
• CL-610 internal
• Power off the CL-610 and
allow it to cool down.
Ensure that the intake and
exhaust vents are not
blocked. Turn the
temperature is too high.
projector back on. If the
problem persists, please
contact your Runco dealer
for assistance.
Runco CL-610 Series Owner’s Operating Manual
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
52
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Serial Communications
To interface the CL-610 with a home theater automation/control system or a PC running
terminal emulation software:
6.1
RS-232 Connection
and Port Configuration
2. Start a terminal session on your PC using a terminal-emulation program, such as
HyperTerminal.
3. Configure the RS-232 controller or PC serial port as follows: no parity, eight data bits,
one stop bit and no flow control. Set the baud rate to match that of the projector
(115200, 38400 or 9600).
4. Press <Enter>.You should see a command prompt (>) in the terminal window.
example, to change the aspect ratio to Letterbox, type x063x <Enter>.
Serial commands to the CL-610 take the following form:
• Commands are in ASCII format.
6.2
Serial Command
Syntax
• Commands are not case-sensitive; X001Xand x001xare equivalent.
• A carriage return MUST follow each command.
The CL-610 will not accept serial commands for 30 seconds after it
is turned on or off.
Note
Table 6-1. Serial Commands
Code
Function
x001x
x002x
x003x
x004x
x005x
x006x
x007x
x008x
x009x
x011x
x021x
Power On
Power Off
Menu
Enter
Exit
Up (arrow key)
Down (arrow key)
Left (arrow key)
Right (arrow key)
Show active source and aspect ratio information
Keypad 1
Runco CL-610 Series Owner’s Operating Manual
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Code
Function
x022x
x023x
x024x
x025x
x026x
x027x
x028x
x029x
x030x
x031x
x032x
x033x
x046x
x047x
x048x
x049x
x051x
x052x
x053x
x054x
x055x
x056x
x057x
x058x
x061x
x062x
x063x
x064x
x065x
x066x
x071x
x072x
Keypad 2
Keypad 3
Keypad 4
Keypad 5
Keypad 6
Keypad 7
Keypad 8
Keypad 9
Keypad 0
Store image settings to Memory 1
Store image settings to ISF Night
Store image settings to ISF Day
Restore image settings from Memory 1
Restore image settings from ISF Night
Restore image settings from ISF Day
Load default of current source
Single source, full-screen
PIP - graphics on video
PIP - video on graphics
PBP - graphics by video
PBP - video by graphics
PIP - increase sub-window size
PIP - decrease sub-window size
Set PIP/PBP active window
Anamorphic (16:9) aspect ratio
Standard (4:3) aspect ratio
Letterbox aspect ratio
VirtualWide aspect ratio
Cinema aspect ratio
Virtual Cinema aspect ratio
RS-232 baud rate = 9600
RS-232 baud rate = 38400
54
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 6-1. Serial Commands (continued)
Code
Function
x073x
x081x
x082x
x083x
x084x
x091x
x092x
x121x
x122x
x123x
x124x
x125x
x131x
x132x
x133x
x134x
x135x
x136x
x156x
x157x
x158x
x161x
x162x
x181x
RS-232 baud rate = 115200
Image orientation = floor front
Image orientation = ceiling front
Image orientation = floor rear
Image orientation = ceiling rear
Lamp Power = 200W
Lamp Power = 250W
OSD Language = English
OSD Language = French
OSD Language = Spanish
OSD Language = German
OSD Language = Italian
Switch to Composite input
Switch to S-Video input
Switch to RGB-HD input
Switch to DVI input (HDMI)
Switch to Component 1 input
Switch to Component 2 input
Background Color = Grey
Background Color = Blue
Background Color = White
Un-freeze Image
Freeze Image
Toggle Blue Image on/off
Runco CL-610 Series Owner’s Operating Manual
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
56
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Specifications
Table 7-1 lists the CL-610 specifications.
7.1
CL-610 Specifications
Table 7-1. CL-610 Specifications
Projector Type:
Native Resolution:
Aspect Ratios:
Digital Light Processing (DLP), Single-Chip DMD
1280 x 720 (16:9)
4:3, Letterbox, 16:9 Anamorphic, VirtualWide, Cinema,
Virtual Cinema
Video Standards:
DTV Compatibility:
Scan Frequency:
NTSC, PAL, SECAM
480p, 576p, 720p, 1080i
Horizontal: 15 - 80 kHz
Vertical: 50 - 100 Hz
Picture Size (16:9 Screen):
Recommended Width: 72 in. (1.83 m) to 96 in. (2.44 m)
Capable of screen widths between 48 in. (1.22 m) and 200 in.
(5.08 m)
Throw Distance
Refer to Table 3-3
(Factor x Screen Width):
Horizontal and Vertical Lens
Shift:
None; electronic image shift via OSD controls
Video Inputs:
(1) Composite Video, (1) S-Video, (1) RGB/Component Video
(5xBNC), (1) RCA Component Video, (1) HDMI
Control Options:
-
-
-
Discrete IR remote
Built-in keypad
Serial commands via RS-232
RS-232 Communication
Parameters:
9600, 38400 or 115200 bps, no parity, 8 data bits, 1 stop bit,
no flow control
12V Output:
Max. 0.25 Amps, active when projector is turned on;
Tip = +12V; Sleeve = Ground
Runco CL-610 Series Owner’s Operating Manual
57
Download from Www.Somanuals.com. All Manuals Search And Download.
Table 7-1. CL-610 Specifications (continued)
Brightness and Contrast:
Cinema Standards Measurement System (CSMS)
Specifications
-
-
Brightness: 14.5 to 21.6 foot-Lamberts (fL)
Contrast Ratio: 200:1 to 220:1
These measurements are taken from the projector in a controlled,
home theater environment. All measurements are made to
ANSI/NAPM IT7.228-1997 specifications using the Photo Research
PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter,
Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The
projector is calibrated to a color temperature of 6,500K and has a
minimum of 150 hours of usage.
The foot-Lambert (fL) is the unit of measurement used in commercial
movie theaters to express image brightness at the screen surface. The
Society of Motion Picture and Television Engineers (SMPTE) specifies
16 fL as the target image brightness for film-based projectors using an
open gate (without film in the projector). More importantly, today
SMPTE specifies 12 fL as the target image brightness in Digital
Cinema theaters. The foot-Lambert measurement is dependent on
screen size, screen gain and projector light output.
Home Theater Calibration Specifications
-
-
Light Output: 442 to 587 ANSI Lumens
Contrast Ratio: 200:1 to 220:1
These specifications are obtained by calibrating the projector as
described above for CSMS measurements.
Industry-Standard Specifications
-
-
Light Output: 1250 ANSI Lumens
Contrast Ratio: 1500:1 to 3100:1
These are typical projector brightness and contrast specifications
found in most companies’ sales literature. Runco includes these
measurements in its literature to allow for direct comparison with other
manufacturers’ projectors. These measurements are typically taken at
9,000K to 13,000K to get expected performance data when the
projector is used in professional, commercial and industrial displays.
Lamp:
250 Watts
Estimated Lamp Life:
Power Requirements:
Operating Environment:
2000 hours
100 to 240 VAC (auto-sensing), 50/60 Hz, 310 Watts
41°F to 95°F (5°C to 35°C), 20% to 80% humidity
(non-condensing)
Dimensions:
Weight (without lens):
Regulatory Approvals:
Limited Warranty:
34 lbs. (15.42 kg)
Complies with FCC, CE C-Tick
Projector: Two (2) years parts and labor from the date of
delivery to the end user.
Lamp: 1000 hours or six (6) months, whichever comes first.
Specifications are subject to change without notice.
58
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 7-1 shows the CL-610 dimensions.
7.2
CL-610 Dimensions
11.0 in. (279.4 mm)
16.5 in. (419.10 mm)
14.80 in. (376.0 mm)
8.86 in. (225.0 mm)
0.91 in. (23 mm)
2.36 in.
(60 mm)
8.07 in.
(205 mm)
12.57 in.
(319.15 mm)
16.31 in. (414.27 mm)
5.56 in. (141.22 mm)
2.66 in. (67.53 mm)
6.12 in. (155.45 mm)
Figure 7-1. CL-610 Dimensions
Runco CL-610 Series Owner’s Operating Manual
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
60
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A. Personalizing the ISF Splash
Screen on the CL-610
This Appendix describes how to personalize the ISF splash screen on the Runco CL-610
Series DLP Projectors.
Only ISF-trained and -certified technicians should attempt this
procedure!
Note
1. Connect a PC to the CL-610 RS-232 port and establish a serial connection; refer to
2. Press MENU on the projector remote control. Use the up- or down-arrow keys to
highlight ISF Calibration and press ENTER. Use the number buttons on the remote
control to enter the ISF Calibration menu passcode, then press ENTER again.
3. Press MENU on the projector remote control. Then, select Splash Screen Timer
from the ISF Calibration menu.
4. Use the left- or right-arrow buttons to set the Splash Screen Timer. This timer controls
how long the startup (Runco/ISF logo) image stays on-screen after you turn on the
projector. The range is from 5 to 60 seconds in 1-second increments. For this
procedure, set it to 30 seconds and press EXIT.
5. In the HyperTerminal window, at the command prompt (>), type U1followed by the
customer name, four or five spaces and the ISF calibrator name:
6. Press <Enter>.
7. Press MENU on the projector remote control. Then, select ISF Calibration from the
Main menu.
8. Select ISF Enable from the ISF Calibration menu and set it to On.
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
9. Power-cycle the projector to see the change:
CALIBRATED FOR:
John Doe By: Tinh Ho
CUSTOM BUILT BY:
Runco CL-610 Series Owner’s Operating Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SERIAL NUMBER
RUMA-011115
rev 10-24-06 v2.0
Runco International • 2900 Faber Street • Union City, CA 94587 • Ph (510) 324-7777 / (800) 23RUNCO / Fax (510) 324-9300
Download from Www.Somanuals.com. All Manuals Search And Download.
|