IMPORTANT NOTES
When you purchase the SRX-98 Special SRX Board 2006 from an
authorized Roland dealer, the included sounds and samples are
licensed, not sold, to you by Roland Corporation, for commercial use
in music production, public performance, broadcast, etc.
INSTALLING THE WAVE EXPANSION BOARD
*
Turn off your instrument.
1. Remove the cover located on the top (or rear) of your
instrument.
*
When turning the unit upside-down, get a bunch of newspapers or
magazines, and place them under the four corners or at both ends to
prevent damage to the buttons and controls. Also, you should try to
orient the unit so no buttons or controls get damaged.
You may use any of the included phrases and/or samples in a
commercial or non-commercial recording without paying any
additional license fees. However, you must strictly adhere to the
following crediting guidelines on any music recording that utilize
material from SRX-98.
*
When turning the unit upside-down, handle with care to avoid
dropping it, or allowing it to fall or tip over.
2. Insert the Wave Expansion Board connector into a connector
for an SRX Series slot, while simultaneously inserting the
board holders into the holes in the Wave Expansion Board.
Reproduction or duplication of this collection or any of the sound
recording contained in the SRX-98, either as they exist on this
expansion board or by any means of reformatting, mixing, filtering,
re-synthesizing, processing, or otherwise editing for use in another
product or for re-sale, is strictly prohibited without the express
written consent of Roland. All unauthorized giving, trading,
lending, renting, re-issue, re-distribution, or re-sale of the sounds
included in the SRX-98 are expressly prohibited.
*
Do not touch any of the printed circuit pathways or connection
terminals.
*
Never use excessive force when installing a circuit board. If it doesn’t
fit properly on the first attempt, remove the board and try again.
3. Use the supplied Installation Tool to turn the holders in the
LOCK direction, so the board will be fastened in place.
In Plain English: Be creative in your application of the SRX-98
sounds, and keep this library for your use only. DO NOT COPY IT.
(To remove the Wave Expansion Board, turn the board holders
in the UNLOCK direction, and lift up the board.)
Roland constantly monitors other soundware releases to check for
copyright infringements, and will prosecute all piracy and copyright
violations to the fullest extent of the law.
*
When circuit board installation is complete, double-check your work.
4. Using the screws removed in Step 1, refasten the cover in its
original position.
THIS LIBRARY IS GUARANTEED TO BE 100% COPYRIGHT
CLEAN.
5. Check if the Wave Expansion Board is correctly installed.
*
If the “EXP” display cannot be selected (doesn’t appear) in the
Waveform Selection Screen (refer to the owner’s manual of the
instrument you use), remove the Wave Expansion Board and install it
properly.
In addition to the items listed under “USING THE UNIT
SAFELY” on page 2, please read and observe the following:
Handling the Board
To avoid the risk of damage to internal components that can be
caused by static electricity, please carefully observe the following
whenever you handle the board.
*
Éteindre l’instrument.
1. Retirer le couvercle situé sur le dessus (ou á l’arrière) de
l’instrument.
*
Before you touch the board, always first grasp a metal object (such as a
water pipe), so you are sure that any static electricity you might have
been carrying has been discharged.
2. Inserer le connecteur de la carte dans un des creneaux pour
la serie SRX tout en enfoncant les supports a carte dans les
trous de celle-ci.
*
*
*
*
When handling the board, grasp it only by its edges. Avoid touching
any of the electronic components or connectors.
Save the bag in which the board was originally shipped, and put the
board back into it whenever you need to store or transport it.
Ne pas toucher aux circuits imprimés ou aux connecteurs.
Ne jamais forcer lors de l’installation de la carte de circuits imprimés.
Si la carte s’ajuste mal au premier essai, enlevez la carte et
recommencez l’installation.
3. Utiliser l’outil d’installation fourni pour tourner les clips de
retenue vers la position de blocage (LOCK) de façon á ce que
la carte soit retenue en place.
Veuillez suivre attentivement les instructions suivantes quand vous
manipulez la carte afin d’éviter tout risque d’endommagement des
pièces internes par l’électricité statique.
(Pour retirer la carte d’expansion Wave, tourner les clips de
retenue de la carte vers la position déblocage (UNLOCK) et
retirer la carte en la soulevant.)
*
Toujours toucher un objet métallique relié à la terre (comme un tuyau
par exemple) avant de manipuler la carte pour vous décharger de
l’électricité statique que vous auriez pu accumuler.
*
Quand l’installation de la carte de circuits imprimés est terminée,
revérifiez si tout est bien installé.
4. Remettre la plaque a sa place et la fixer a l’aide des vis
*
*
Lorsque vous manipulez la carte, la tenir par les côtés. Évitez de
toucher aux composants ou aux connecteurs.
Conservez le sachet d’origine dans lequel était la carte lors de l’envoi et
remettez la carte dedans si vous devez la ranger ou la transporter.
enlevees a l’etape 1.
5. S’assurer que la carte d’expansion Wave est installée
correctement.
*
S’il est impossible de sélectionner l’affichage “EXP” (il n’apparaît pas)
á l’écran de sélection Waveform (se reporter au guide du propriétaire
de l’instrument utilisé), retirer la carte d’expansion Wave et la
réinstaller correctement.
Wave Expansion Board (SRX series)
Carte d'extension Wave (serie SRX)
1
2
3
Screwdriver
Tournevis
LOCK
Connector
Connecteur
Installation tool
Board holder
Outil d'installation
Support à carte
Position them as shown before you install the board.
Avant l’installation, orienter les supports à carte tel qu’indiqué sur le schéma.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
