®
With Universal Dock for iPod
Model No. PFTL57809.0
Serial No.
USERʼS MANUAL
Write the serial number in the space
above for future reference.
Serial Number
Decal
QUESTIONS?
If you have questions, or if parts are
damaged or missing, DO NOT CON-
TACT THE STORE; please contact
Customer Care.
IMPORTANT: Please register this
product (see the limited warranty
on the back cover of this manual)
before contacting Customer Care.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read all important precautions and in-
structions in this manual and all warnings on your treadmill before using your treadmill. ICON as-
sumes no responsibility for personal injury or property damage sustained by or through the use of
this product.
1. Before beginning any exercise program, con-
sult your physician. This is especially impor-
tant for persons over age 35 or persons with
pre-existing health problems.
should be on the same circuit. Do not use an
extension cord.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
page 13. To purchase a surge suppressor, see
your local PROFORM dealer or call the tele-
phone number on the front cover of this man-
ual and order part number 146148, or see your
local electronics store.
2. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least 8 ft. (2.4 m) of clearance behind it and 2
ft. (0.6 m) on each side. Do not place the
treadmill on any surface that blocks air open-
ings. To protect the floor or carpet from dam-
age, place a mat under the treadmill.
12. Failure to use a properly functioning surge
suppressor could result in damage to the con-
trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may slow,
accelerate, or stop unexpectedly, which may
result in a fall and serious injury.
4. Keep the treadmill indoors, away from mois-
ture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
13. Keep the power cord and the surge suppres-
sor away from heated surfaces.
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROU-
BLESHOOTING on page 22 if the treadmill is
not working properly.)
6. Keep children under age 12 and pets away
from the treadmill at all times.
7. The treadmill should be used only by persons 15. Read, understand, and test the emergency
weighing 300 lbs. (136 kg) or less.
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 15).
8. Never allow more than one person on the
treadmill at a time.
16. Never start the treadmill while you are stand-
ing on the walking belt. Always hold the
handrails while using the treadmill.
9. Wear appropriate exercise clothes while
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended
for both men and women. Always wear ath-
letic shoes; never use the treadmill with bare
feet, wearing only stockings, or in sandals.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. The pulse sensor is not a medical device.
Various factors, including the user's move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
10. When connecting the power cord (see page
13), plug the power cord into a surge sup-
pressor (not included) and plug the surge
suppressor into a grounded circuit capable of
carrying 15 or more amps. No other appliance
3
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Never leave the treadmill unattended while it
is running. Always remove the key, unplug
the power cord, and switch the reset/off cir-
cuit breaker to the off position when the
treadmill is not in use. (See the drawing on
page 5 for the location of the circuit breaker.)
23. Inspect and properly tighten all parts of the
treadmill regularly.
24.
DANGER:
Always unplug the power
cord immediately after use, before cleaning the
treadmill, and before performing the mainte-
nance and adjustment procedures described in
this manual. Never remove the motor hood un-
less instructed to do so by an authorized ser-
vice representative. Servicing other than the
procedures in this manual should be performed
by an authorized service representative only.
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 lbs. (20 kg)
to raise, lower, or move the treadmill.
25. This treadmill is intended for in-home use
only. Do not use this treadmill in a commer-
cial, rental, or institutional setting.
21. When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
26. Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
22. Never insert any object into any opening on
the treadmill.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
®
Thank you for selecting the new PROFORM 595 LT
ing this manual, please see the front cover of this man-
ual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
®
treadmill with Universal Dock for iPod . The 595 LT
treadmill with Universal Dock for iPod offers a selection
of features designed to make your workouts at home
more effective and enjoyable. And when youʼre not ex-
ercising, the treadmill can be folded up, requiring less
than half the floor space of other treadmills.
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after read-
Accessory Tray
Console
Pulse Sensor
Handrail
Latch
Key/Clip
Upright
Reset/Off
Circuit Breaker
Walking Belt
Foot Rail
Platform Cushion
Idler Roller
Adjustment Bolts
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.
Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials. Do not
dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking
belt is coated with high-performance lubricant. During shipping, some lubricant may be transferred to the top of
the walking belt or the shipping carton. This is normal and does not affect treadmill performance. If there is lubri-
cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.
Assembly requires the included hex keys and your own Phillips screwdriver
adjustable wrench , scissors , and needlenose pliers
,
.
Use the drawings below to identify the assembly hardware. The number in parentheses below each drawing is
the key number of the part, from the PART LIST near the end of this manual. The number after the parentheses
is the quantity needed for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached
to one of the parts to be assembled. Extra hardware may be included. To avoid damaging plastic parts,
do not use power tools for assembly.
M4.2 Star
Washer (70)–2
M8 Star
Bolt Spacer (79)–4
M10 Star
Washer (10)–4
Washer (8)–4
Base Pad Spacer
(104)–2
M4.2 x 19mm
Screw (1)–4
M4 x 20mm
Screw (3)–2
M4.2 x 25mm
Tek Screw (2)–4
#10 x 1" Tek
Screw (76)–2
M8 x 25mm Bolt (6)–4
M10 x 96mm Bolt (5)–4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. Make sure that the power cord is unplugged.
1
B
With the help of a second person, carefully tip
the treadmill onto its left side. Partially fold the
Frame (48) so that the treadmill is more stable;
do not fully fold the Frame yet.
A
77
Hole
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
2
81
48
Cut the shipping tie securing the Upright Wire
(77) to the Base (85). Locate a tie in the indi-
cated hole in the Base, and use the tie to pull the
Upright Wire out of the hole.
85
104
81
2
Attach a Base Pad (81) to the Base (85) in the
location shown with a Base Pad Spacer (104)
and an M4.2 x 25mm Tek Screw (2). Then, at-
tach a Base Pad (81) in the location shown with
only an M4.2 x 25mm Tek Screw (2).
2. Remove the M10 Nut (33), the M10 x 50mm Bolt
(4), and the shipping bracket (C) from the Base
(85). Attach a Wheel (86) with the Bolt and the
Nut that you just removed. Do not overtighten
the Nut; the Wheel must turn freely. Discard
the shipping bracket.
2
4
85
86
C
33
7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Identify the Right Upright (78) and the Right
Upright Spacer (80), which are marked with
“Right” stickers. Insert the Upright Wire (77)
through the Right Upright Spacer as shown. Set
the Right Upright Spacer on the Base (85).
3
Wire Tie
78
77
77
80
With the help of a second person, hold the Right
Upright (78) near the Base (85). See the inset
drawing. Tie the wire tie in the Right Upright se-
curely around the end of the Upright Wire (77).
Then, pull the other end of the wire tie until the
Upright Wire is routed completely through the
Right Upright.
85
78
Wire
77
Tie
4. Hold a Bolt Spacer (79) inside the lower end of
the Right Upright (78). Insert an M10 x 96mm
Bolt (5) with an M10 Star Washer (8) into the
Right Upright and the Bolt Spacer. Repeat this
step with a second Bolt Spacer (79), M10 x
96mm Bolt (5), and M10 Star Washer (8).
4
5
78
8
77
79
Hold the Right Upright (78) against the Right
Upright Spacer (80). Be careful not to pinch
the Upright Wire (77). Partially tighten the M10
x 96mm Bolts (5); do not fully tighten the
Bolts yet.
82
79
80
Press a Base Cap (82) into the Base (85).
85
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5. With the help of a second person, carefully tip
the treadmill onto its right side. Partially fold the
Frame (48) so the treadmill is more stable; do
not fully fold the Frame yet.
5
B
A
Remove and discard the two indicated bolts (A)
and the shipping bracket (B).
48
Attach a Base Pad (81) to the Base (85) in the
location shown with a Base Pad Spacer (104)
and an M4.2 x 25mm Tek Screw (2). Then, at-
tach a Base Pad (81) in the location shown with
only an M4.2 x 25mm Tek Screw (2).
4
81
2
104
2
85
86
Remove the M10 Nut (33), the M10 x 50mm
Bolt (4), and the shipping bracket (C) from the
Base (85). Attach a Wheel (86) with the Bolt and
the Nut that you just removed. Do not over-
tighten the Nut; the Wheel must turn freely.
Discard the shipping bracket.
81
C
33
6. With the help of a second person, hold a Bolt
Spacer (79) inside the lower end of the Left
Upright (73). Insert an M10 x 96mm Bolt (5) with
an M10 Star Washer (8) into the Left Upright
and the Bolt Spacer. Repeat this step with a
second Bolt Spacer (79), M10 x 96mm Bolt
(5), and M10 Star Washer (8).
6
73
5
8
83
Orient the Left Upright (73) and the Left Upright
Spacer (83) as shown. Hold the Left Upright
Spacer and the Left Upright against the Base
(85). Partially tighten the M10 x 96mm Bolts (5);
do not fully tighten the Bolts yet.
82
79
85
Press a Base Cap (82) into the Base (85).
With the help of a second person, tip the tread-
mill so that the Base (85) is flat on the floor.
7. Set the Console Base (88) face down on a soft
surface to avoid scratching the Console (not
shown). Remove the six M4.2 x 19mm Screws
(1). Save all six Screws for step 9.
7
1
Lift off the Pulse Support (109).
1
88
1
109
9
Download from Www.Somanuals.com. All Manuals Search And Download.
8. Identify the Right Handrail (90), which has a
large hole in the location shown. Hold the Right
Handrail near the Console Base (88).
8
Console
Wire
Tie
Insert the tie on the console wire into the large
hole in the Right Handrail (90) and out of the top
as shown; use needlenose pliers if necessary.
Next, insert the included plastic tie through the
Right Handrail as shown. Make sure that the
plastic tie holds the console wire against the
inner side. Then, tighten the plastic tie.
90
Plastic Tie
1
Large Hole
1
Attach the Right Handrail (90) with two M4.2 x
19mm Screws (1). Make sure that no wires are
pinched. Start both Screws before tightening
either of them; do not overtighten the
Screws. Then, remove the plastic tie.
88
Attach the Left Handrail (not shown) to the
Console Base (88) in the same way. There are
no wires on the left side of the Console Base.
9. Hold the Pulse Support (109) near the Console
Base (88). Connect the Console Ground Wire
(40) on the Pulse Support to the ground wire on
the Console Base. Then, insert the ground wires
into the Console Base and set the Pulse
Support on the Console Base. Make sure that
no wires are pinched.
9
70
3
1
1
88
Tighten two M4 x 20mm Screws (3) with two
M4.2 Star Washers (70) into the Pulse Support
(109).
1
109
1
3
70
Tighten the six M4.2 x 19mm Screws (1) from
step 7 into the Pulse Support (109) and the
Console Base (88). Start all six Screws before
tightening any of them.
40
Ground
Wire
10
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Remove the plastic ties from the Right Handrail
(90) and the Left Handrail (not shown). If neces-
sary, press the Cage Nuts (38) into place.
10
Console Assembly
Have a second person hold the console assem-
bly near the Right Upright (78).
Connect the Upright Wire (77) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF THE CONNECTORS ARE NOT CON-
NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON. Remove the wire tie from the
Upright Wire and the tie from the console wire.
Then, insert the connectors into the Right Upright
(78).
38
Plastic
90
Ties
Console
Console
Wire
Wire
77
Set the console assembly on the Right Upright
(78) and the Left Upright (not shown). Make sure
that no wires are pinched.
77
Wire
Tie
78
11. Partially tighten two M8 x 25mm Bolts (6) with
two M8 Star Washers (10) into the Left Upright
(73) and the Left Handrail (89).
11
110
Next, partially tighten two M8 x 25mm Bolts (6)
with two M8 Star Washers (10) into the Right
Upright (78) and the Right Handrail (90). Then,
tighten all four Bolts.
111
88
See steps 4 and 6. Tighten the M10 x 96mm
Bolts (5).
89
Press the Left Accessory Tray (110) and the
Right Accessory Tray (111) into the Console
Base (88).
6
10
10
6
73
90
6
10
78
10
6
11
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Attach the Latch Housing (71) to the Left Upright
(73) with two #10 x 1" Tek Screws (76). Make
sure that the large hole in the Latch Housing
is on the side shown. Do not overtighten the
Latch Screws.
12
Locate the Latch Assembly (72). Remove the
knob from the pin. Make sure that the collar and
the spring are on the pin. Then, insert the pin
into the Latch Housing (71), and tighten the
knob back onto the pin.
73
Spring
71
Knob
76
Collar
Pin
72
Large
Hole
13. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear
plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread-
mill. Keep the included hex keys in a secure place; one of the hex keys is used to adjust the walking belt (see
pages 23 and 24).
If you purchase the optional chest pulse sensor (see page 19), follow the steps below to install the re-
ceiver included with the chest pulse sensor.
1. Make sure that the power cord is unplugged.
Remove the indicated M4.2 x 16mm Screw (12)
88
and the Access Door (97) from the Console
Base (88).
2. Connect the wire on the receiver to the indi-
cated wire extending from the Console Base
(88). Hold the receiver so the antenna is ori-
ented as shown and is facing the Console
Base. Attach the receiver to the plastic posts on
Wire
the Access Door (97) with the two included
Small
small screws.
Screws
Receiver
Wire
3. Make sure that no wires are pinched.
Reattach the Access Door (97) with the M4.2 x
16mm Screw (12). Discard the other wires in-
cluded with the receiver.
Antenna
97
12
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
IMPORTANT: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with high-
performance lubricant. IMPORTANT: Never apply sil-
icone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illus-
trated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER:
Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or service-
man if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
installed by a qualified electrician.
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your homeʼs power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local PROFORM dealer or call the telephone
number on the front cover of this manual and order
part number 146148, or see your local electronics
store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Surge Suppressor
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge sup-
pressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a moni-
toring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may slow, accelerate, or stop unexpectedly, which
may result in a fall and serious injury.
Lug
Metal Screw
Grounding Plug
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified elec-
trician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunc-
tion or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONSOLE DIAGRAM
Integrated Universal Dock for iPod
Key
Clip
FEATURES OF THE CONSOLE
certified by the developer to meet Apple performance
standards.
The treadmill console offers an impressive array of
features designed to make your workouts more effec-
tive and enjoyable.
To turn on the power, see page 15. To use the man-
ual mode, see page 15. To use the weight loss cen-
ter, see page 17. To use a classic workout, see
page 18. To use the stereo sound system, see page
19. To use the information mode, see page 19.
When you use the manual mode, you can change the
speed and incline of the treadmill with the touch of a
button. As you exercise, the console will display instant
exercise feedback. You can even measure your heart
rate using the handgrip pulse sensor or the optional
chest pulse sensor (see page 19).
IMPORTANT: If there are sheets of clear plastic on
the console, remove the plastic. To prevent damage
to the walking platform, wear clean athletic shoes
while using the treadmill. The first time you use the
treadmill, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 24).
You can customize your workout using one of the four
calorie goal workouts in the weight loss center. In addi-
tion, the console features eight iFit classic workouts.
Each workout automatically controls the speed and in-
cline of the treadmill as it guides you through an effec-
tive exercise session.
Note: The console can display speed and distance in
either miles or kilometers. To find out which unit of
measurement is selected or to change the unit of mea-
surement, see THE INFORMATION MODE on page
19. Note: For simplicity, all instructions in this section
refer to miles.
You can even listen to your favorite workout music or
audio books with the consoleʼs premium stereo sound
system while you get in shape. This product has been
designed specifically to work with iPod and has been
14
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
1. Insert the key into the console.
See HOW TO TURN ON THE POWER at the left.
2. Select the manual mode.
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room tem-
perature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
Plug in the power cord (see
page 13). Next, locate the
reset/off circuit breaker on
When the key is in-
serted, the manual
mode will be se-
the treadmill frame near the
power cord. Switch the cir-
cuit breaker to the reset po-
sition.
Reset
lected. If you have
selected the weight
loss center or a clas-
sic workout, remove the key and then reinsert it.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is dis-
played in a store. If the displays light as soon as
you plug in the power cord and switch the reset/off
circuit breaker to the reset position, the demo
mode is turned on. To turn off the demo mode,
hold down the Stop button for a few seconds. If the
displays remain lit, see THE INFORMATION MODE
on page 19 to turn off the demo mode.
3. Start the walking belt.
To start the walking belt, press the Start button, the
Speed increase button, or one of the Precision
Quick Speed buttons numbered 1 through 10.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 1 mph.
As you exercise, change the speed of the walking
belt as desired by pressing the Speed increase and
decrease buttons. Each time you press one of the
buttons, the speed setting will change by 0.1 mph; if
you hold down the button, the speed setting will
change in increments of 0.5 mph. Note: After you
press a button, it may take a moment for the walk-
ing belt to reach the selected speed setting.
Next, stand on the foot rails of the treadmill. Find the
clip attached to the key (see the drawing on page 14)
and slide the clip onto the waistband of your clothes.
Then, insert the key into the console. After a moment,
the displays will light. IMPORTANT: In an emergency
situation, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the posi-
tion of the clip.
If you press one of the numbered speed buttons,
the walking belt will gradually change speed until it
reaches the selected speed setting. To select a
speed setting that includes a decimal—such as 3.5
mph—press two numbered buttons in succession.
For example, to select a speed setting of 3.5 mph,
press the 3 button and then immediately press the
5 button.
To stop the walking belt, press the Stop button. To
restart the walking belt, press the Start button or
the Speed increase button.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Change the incline of the treadmill as desired.
6. Measure your heart rate if desired.
To change the incline of the treadmill, press the
Incline increase or decrease button. Each time you
press the Incline increase or decrease button, the
incline will change by 0.5%. Note: After you press
an incline button, it may take a moment for the
treadmill to reach the selected incline setting.
Note: If you use the handgrip pulse sensor and
the optional chest pulse sensor at the same
time, the display will not show your heart rate
accurately. See page 19 for information on the op-
tional chest pulse sensor.
Before using the
handgrip pulse
sensor, remove
the sheets of
5. Select a display mode and monitor your
progress with the display.
When the manual mode is selected, the console
offers two display modes. Press the Display button
repeatedly to select the desired display mode.
clear plastic from
the metal con-
Contacts
tacts on the pulse
bar. In addition,
As you walk or run on the treadmill, the display can
show the following workout information:
make sure that
your hands are clean.
• A 1/4-mile (400 meter) track.
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on the
metal contacts. Avoid moving your hands. When
your pulse is detected, a heart symbol will flash in
the display each time your heart beats and then
your heart rate will be shown. For the most accu-
rate heart rate reading, continue to hold the
contacts for about 15 seconds.
• The number of laps you have completed.
• The elapsed time.
• The distance that you have walked or run.
• The approximate number of calories you have
burned.
7. When you are finished exercising, remove the
key from the console.
• The incline level of the treadmill.
• The speed of the walking belt.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest set-
ting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
Regardless of which display mode you select, the
speed or incline setting will appear in the display
for a few seconds each time you change the set-
ting. In addition, your heart rate will appear in the
display each time you use the handgrip pulse sen-
sor or the optional chest pulse sensor.
When you are finished using the treadmill, switch
the reset/off circuit breaker to the “off” position and
unplug the power cord. IMPORTANT: If you do
not do this, the treadmillʼs electrical compo-
nents may wear prematurely.
To reset the console, press the Stop button, re-
move the key, and then reinsert the key.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE WEIGHT LOSS CENTER
1. Insert the key into the console.
cline buttons; however, when the next segment
begins, the treadmill will automatically adjust to
the speed and incline settings for the next seg-
ment.
See HOW TO TURN ON THE POWER on page 15.
2. Select a weight loss workout.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next seg-
ment of the workout begins, the treadmill will auto-
matically adjust to the speed and incline settings
for the next segment.
To use a calorie goal workout, press the Weight
Loss Center button.
Input your weight, the number of calories you wish
to burn, and the desired workout duration by re-
peatedly pressing the increase or decrease button
next to the Weight Loss Center button. Hold down
the increase or decrease button to rapidly change
your weight or the workout duration. Press the
Enter button after each selection. Note: Once you
have entered your weight, it will be saved in mem-
ory. The profiles on the console represent the
speed settings of the workout.
4. Select a display mode and monitor your
progress with the display.
When the weight loss center is selected, the con-
sole offers two display modes. Press the Display
button repeatedly to select the desired display
mode. The display can show the following workout
information:
3. Start the walking belt.
• Workout informa-
tion bars which
show your
Press the Start button or the Speed increase button
to start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
progress during
the workout.
• A profile of the speed settings of the workout.
The arrow below the profile will indicate your
progress.
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed setting
and/or incline setting may be programmed for con-
secutive segments.
• The time remaining.
• The distance that you have walked or run.
Tones will sound at the end of each segment. If a
different speed setting and/or incline setting is pro-
grammed for the second segment, the speed set-
ting and/or incline setting will flash in the display for
a moment to alert you. The treadmill will then auto-
matically adjust to the speed and incline settings
for the second segment.
• The approximate number of calories you have
burned.
• The incline level of the treadmill.
• The speed of the walking belt.
5. Measure your heart rate if desired.
See step 6 on page 16.
The workout will continue in this way until the last
segment ends. The walking belt will then slow to a
stop.
6. When you are finished exercising, remove the
key from the console.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually
override the setting by pressing the speed or in-
See step 7 on page 16.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE A CLASSIC WORKOUT
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 15.
2. Select a classic workout.
incline setting will flash in the display for a moment
to alert you. The treadmill will then automatically
adjust to the speed and incline settings for the sec-
ond segment. The arrow will then move one seg-
ment to the right.
The workout will continue in this way until the arrow
reaches the right end of the profile and the last
segment ends. The walking belt will then slow to a
stop.
To select a classic
workout, press the
Classic Workouts
button repeatedly.
If the speed or incline setting for the current seg-
ment is too high or too low, you can override the
setting by pressing the speed or incline buttons;
however, when the next segment begins, the
treadmill will automatically adjust to the speed
and incline settings for the next segment.
The duration, the
maximum speed
setting, the maximum incline setting, and the num-
ber of the workout will appear in the display. In ad-
dition, a profile of the speed settings of the workout
will appear.
To stop the workout at any time, press the Stop
button. To restart the workout, press the Start but-
ton. The walking belt will begin to move at 1 mph.
When the next segment of the workout begins, the
treadmill will automatically adjust to the speed and
incline settings for the next segment.
3. Start the walking belt.
Press the Start button or the Speed increase button
to start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
4. Select a display mode and monitor your
progress with the display.
Each workout is divided into one-minute segments.
One speed setting and one incline setting are pro-
grammed for each segment. Note: The same
speed setting and/or incline setting may be pro-
grammed for consecutive segments.
See step 5 on page 16. Note: The display will show
a profile of the speed settings of the workout in-
stead of a track and the number of laps you have
completed.
A profile of the speed settings of the workout will
appear in the display. A small arrow below the pro-
file will indicate your progress.
5. Measure your heart rate if desired.
See step 6 on page 16.
At the end of the first one-minute segment of the
workout, a series of tones will sound. If a different
speed setting and/or incline setting is programmed
for the second segment, the speed setting and/or
6. When you are finished exercising, remove the
key from the console.
See step 7 on page 16.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO USE THE STEREO SOUND SYSTEM
The display will show
the total number of
hours the treadmill has
been used.
This product has been designed specifically to work
with iPod and has been certified by the developer to
meet Apple performance standards. To play music or
audio books through the consoleʼs stereo speakers,
you must connect your iPod, MP3 player, CD player,
or other personal audio player to the console through
the audio jack or through the Integrated Universal
Dock for iPod. The Integrated Universal Dock for iPod
will charge your iPod while you use it.
The display will also show the total number of miles or
kilometers that the walking belt has moved.
The word ENGLISH for miles or METRIC for kilometers
will appear in the display. Press the Speed increase
button to change the unit of measurement if desired.
To use the audio jack, locate the audio wire and plug it
into the audio jack near the speakers. Then, plug the
audio wire into a jack on your MP3 player, CD player,
or personal audio player. Make sure that the audio
wire is fully plugged in.
The console features a display demo mode, designed
to be used if the treadmill is displayed in a store. While
the demo mode is turned on, the console will function
normally when you plug in the power cord, switch the
reset/off circuit breaker to the reset position, and insert
the key into the console. However, when you remove
the key, the displays will remain lit, although the but-
tons will not function. If the demo mode is turned on,
the word ON will appear in the display while the infor-
mation mode is selected. To turn on or turn off the
demo mode, press the Speed decrease button.
To use the Integrated Universal Dock for iPod, you
need an iFit Universal iPod Connector (not included).
Plug one end into the Integrated Universal Dock for
iPod near the speakers and the other end into your
iPod. Make sure that the iFit Universal iPod
Connector is fully plugged in. To purchase an iFit
Universal iPod Connector, see the front cover of this
manual.
To exit the information mode, remove the key from the
console.
Next, press the Play button on your iPod, MP3 player,
CD player, or other personal audio player. Adjust the
volume on your personal audio player or press the
Volume increase and decrease buttons on the con-
sole.
THE OPTIONAL CHEST PULSE SENSOR
An optional chest pulse sensor offers hands-free oper-
ation as it tracks your heart rate during your workouts.
To purchase the optional chest pulse sensor, call
the telephone number on the front cover of this
manual.
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat sur-
face instead of on the console.
THE INFORMATION MODE
The console features an information mode that keeps
track of the total distance that the walking belt has
moved and the total number of hours that the treadmill
has been used. The information mode also allows you
to select a measurement system of miles or kilome-
ters, and to turn on and turn off the display demo
mode.
To select the information mode, hold down the Stop
button while inserting the key into the console and then
release the Stop button. When the information mode is
selected, the following information will be shown:
19
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If you do not do this, you may damage the
treadmill when you fold it. Remove the key and unplug the
power cord. CAUTION: You must be able to safely lift 45
lbs. (20 kg) to raise, lower, or move the treadmill.
Frame
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibil-
ity of injury, do not lift the frame by the plastic foot
rails. Make sure to bend your legs and keep your
back straight as you raise the frame. Raise the frame
about halfway to the vertical position.
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob
to the left and hold it. Raise the frame until the latch pin is
aligned with the gap between the frame and the walking
platform, and then slowly release the latch knob. Make
Frame
sure that the latch pin is fully inserted into the gap.
Walking
Platform
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of di-
rect sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 85° F (30° C).
Engaged
Latch
Pin
Latch
Knob
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert it to the storage position
as described above. Make sure that the latch pin is fully
inserted into the gap.
Frame
Handrail
1. Hold a handrail and the frame and place one foot against
one of the wheels.
2. Tip the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location.
Never move the treadmill without tipping it back. To
reduce the risk of injury, use extreme caution while
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface. Do not pull back on
the frame.
Wheel
3. Place one foot against a wheel, and carefully lower the
treadmill until it is resting in the storage position.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill with your right hand. Pull the
latch knob to the left and hold it. Pivot the frame
downward until it is past the latch pin. Then, slowly
release the latch knob.
Frame
Pin
Latch
Knob
2. Hold the metal frame firmly with both hands and
lower it to the floor. CAUTION: Do not grip only
the plastic foot rails or drop the frame to the
floor. Bend your legs and keep your back
straight.
Frame
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 13). Use only a single-outlet surge suppres-
sor that meets all of the specifications described on page 13. IMPORTANT: The treadmill is not
compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
c
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has
tripped. To reset the circuit breaker, wait for five
Reset
minutes and then press the switch back in.
Tripped
PROBLEM: The power turns off during use
SOLUTION: a. Check the reset/off circuit breaker (see the drawing above). If the circuit breaker has tripped, wait
for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The console displays remain lit when you remove the key from the console
SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a
store. If the displays remain lit when you remove the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 19 and turn off the demo mode.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG
a
73
THE POWER CORD. With the help of a second
person, carefully tip the Uprights (73, 78) down.
There may be two Screws (A) in the bottom of the
Belly Pan (69). If there are, remove them. Note: A
Phillips screwdriver with a shaft at least 5 in. (13
cm) long is required.
69
A
78
A
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Remove the three M4.2 x 19mm Hood Screws (13)
and carefully pivot the Motor Hood (53) off.
13
53
Locate the Reed Switch (54) and the Magnet (42)
on the left side of the Pulley (44). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If neces-
sary, loosen the M4.2 x 19mm Screw (1), move the
Reed Switch slightly, and then retighten the Screw.
Reattach the Motor Hood (not shown), and run the
treadmill for a few minutes to check for a correct
speed reading.
1/8 in.
1
42
54
44
Top
View
PROBLEM: The incline of the treadmill does not change correctly
SOLUTION: a. With the key in the console, press one of the Incline buttons. While the incline is changing, re-
move the key. After a few seconds, re-insert the key. The treadmill will automatically rise to the
maximum incline level and then return to the minimum level. This will recalibrate the incline system.
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 13.
b. If the walking belt is overtightened, treadmill perfor-
b
mance may decrease and the walking belt may be-
come damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller bolts counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walk-
ing belt is properly tightened.
2–3 in.
Idler Roller Bolts
c. If the walking belt still slows when walked on, see the front cover of this manual.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the
key and UNPLUG THE POWER CORD. If the
walking belt has shifted to the left, use the hex
key to turn the left idler roller bolt clockwise 1/2 of a
turn; if the walking belt has shifted to the right,
turn the left idler roller bolt counterclockwise 1/2 of
a turn. Be careful not to overtighten the walking
belt. Then, plug in the power cord, insert the key,
and run the treadmill for a few minutes. Repeat
until the walking belt is centered.
a
b. If the walking belt slips when walked on, first re-
move the key and UNPLUG THE POWER CORD.
Using the hex key, turn both idler roller bolts clock-
wise, 1/4 of a turn. When the walking belt is cor-
rectly tightened, you should be able to lift each side
of the walking belt 2 to 3 in. (5 to 7 cm) off the
walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert
the key, and carefully walk on the treadmill for a
few minutes. Repeat until the walking belt is prop-
erly tightened.
b
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exer-
cise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physi-
cian. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is in-
tended only as an exercise aid in determining
heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic exer-
cise, which is activity that requires large amounts of
oxygen for prolonged periods of time. For aerobic ex-
ercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching
and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper inten-
sity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 min-
utes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise–never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretch-
ing. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the near-
est ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest be-
tween workouts. After a few months of regular exer-
cise, you may complete up to five workouts each
week, if desired. Remember, the key to success is to
make exercise a regular and enjoyable part of your
everyday life.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFTL57809.0
To locate the parts listed below, see the EXPLODED DRAWING near the end of this manual.
R1109A
Key No. Qty.
Description
Key No. Qty.
Description
1
19
4
2
2
4
4
1
4
2
4
5
13
3
2
2
2
2
1
1
2
1
7
8
2
2
1
1
4
2
2
3
2
4
1
2
2
3
4
1
1
2
1
1
1
1
1
1
1
1
2
M4.2 x 19mm Screw
M4.2 x 25mm Tek Screw
M4 x 20mm Screw
M10 x 50mm Bolt
M10 x 96mm Bolt
M8 x 25mm Bolt
3/8" Star Washer
M10 Star Washer
M8 Nut
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
1
1
1
1
1
2
1
1
2
1
1
3
1
2
1
1
1
1
1
2
1
1
1
1
1
2
1
1
4
1
4
2
1
2
1
2
1
1
1
1
2
2
1
2
10
1
1
1
1
1
Left Foot
2
Right Foot
3
Motor Hood
4
Reed Switch
5
Reed Switch Clamp
Frame Spacer
Frame/Roller Ground Wire
Incline Motor
6
7
8
9
Idler Roller Bracket
Drive Motor
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
M8 Star Washer
M4.2 x 13mm Belly Pan Screw
M4.2 x 16mm Screw
M4.2 x 19mm Hood Screw
M8 x 35mm Screw
M8 x 90mm Screw
M10 x 30mm Bolt
M6 x 70mm Bolt
3/8" x 1 3/4" Bolt
3/8" x 1 1/2" Bolt
3/8" x 1" Bolt
Drive Motor Bracket
Lift Frame Cable Tie
Lift Frame
M8 Flange Nut
Power Cord
Controller
Power Cord Grommet
Reset/Off Circuit Breaker
Belly Pan
M4.2 Star Washer
Latch Housing
Latch Assembly
Left Upright
M6 x 45mm Bolt
M4.2 x 13mm Ground Screw
M5.5 x 25mm Screw
1/4" x 3/8" Bolt
Left Bottom Pulse Plate
Audio Wire
3/8" x 3/4" Bolt
3/8" x 4" Bolt
#10 x 1" Tek Screw
Upright Wire
#8 x 1/2" Ground Screw
M4.2 x 13mm Screw
M6 Split Washer
M6 Washer
Right Upright
Bolt Spacer
Right Upright Spacer
Base Pad
3/8" Jam Nut
3/8" Motor Nut
Base Cap
M10 Nut
Left Upright Spacer
Caution Decal
Base
6mm Hex Key
Platform Cushion
3/8" Locknut
Wheel
Hood Clip
Console
Cage Nut
Console Base
Left Handrail
Left Foot Rail
Console Ground Wire
Belt Guide
Right Handrail
Handrail Cap, Lower
Cable Tie
Magnet
Drive Belt
Key/Clip
Drive Roller/Pulley
Walking Belt
Releasable Tie
8" Cable Tie
Walking Platform
Right Foot Rail
Left Top Pulse Plate
Access Door
Frame
15 1/2" Cable Tie
Lift Motor Spacer
Idler Roller
Warning Decal
Idler Roller Bracket Plate
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
107
108
109
110
111
112
4
1
2
2
1
1
4
1
1
1
1
2
#3 x 1/4" Screw
113
1
1
1
1
–
–
–
–
–
Right Bottom Pulse Plate
Right Top Pulse Plate
Key Plate
Lift Frame/Base Ground Wire
Frame Cap
114
115
Base Pad Spacer
4 mm Hex Key
116
Incline Motor Wire
8" Blue Wire, 2F
6" Blue Wire, M/F
6" Black Wire, M/F
6" Red Wire, M/F
Userʼs Manual
*
*
*
*
*
5 mm Hex Key
Clamp
Controller Ground Wire
Pulse Support
Left Accessory Tray
Right Accessory Tray
Handrail Cap, Upper
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. PFTL57809.0
R1109A
3
2
3
0
1
1
4
4
4
4
6
7
4
3
2
4
8
1
2
3
4
5
3
1
2
4
6
4
3
2
6
1
8
2
4
2
3
2
5
3
4
4
0
7
1
1
5
4
9
6
5
9
1
3
2
8
2
1
5
4
1
0
2
0
2
1
0
2
3
5
5
3
1
9
0
2
5
3
2
7
1
9
3
9
4
4
9
3
1
6
0
5
1
1
3
2
2
5
0
1
2
1
9
5
5
0
3
0
9
5
2
3
2
7
1
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. PFTL57809.0
R1109A
13
53
37
13
37
13
25
37
7
25
60
24
32
61
1
54
56
55
22
102
63
31
22
33
21
62
26
33
18
31
56
116
12
58
99
31
108
65
66
19
11
11
11
67
22
11
68
11
69
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING C—Model No. PFTL57809.0
R1109A
6
10
6
10
71
72
73
76
77
6
10
10
6
83
5
82
36
78
8
20
79
84
36
81
2
20
82
4
77
85
84
104
81
33
8
86
81
2
2
5
80
33
86
79
104
81
2
4
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING D—Model No. PFTL57809.0
R1109A
112
87
1
1
89
101
110
91
12
38
75
101
12
96
113
12
74
114
111
12
97
1
12
115
112
1
12
109
88
12
27
1
1
1
70
3
40
1
93
90
91
12
1
1
3
38
107
70
94
98
92
95
31
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-
vide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED
DRAWING near the end of this manual)
LIMITED WARRANTY
IMPORTANT: You must register this product within 30 days of the purchase date to avoid added
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for ten (10) years from
the date of purchase. Parts and labor are warranted for ninety (90) days from the date of purchase.
This warranty extends only to the original purchaser. ICONʼs obligation under this warranty is limited to
repairing or replacing, at ICONʼs option, the product through one of its authorized service centers. All re-
pairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customerʼs responsibility. For
replacement parts shipped while the product is under warranty, the customer will be responsible for a
minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge.
This warranty does not extend to any damage to a product caused by or attributable to freight damage,
abuse, misuse, improper or abnormal usage, or repairs not provided by an ICON authorized service cen-
ter; to products used for commercial or rental purposes or as store display models; or to products trans-
ported or purchased outside the US. No other warranty beyond that specifically set forth above is autho-
rized by ICON.
ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-
nection with the use or performance of the product; damages with respect to any economic loss, loss of
property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of in-
cidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of
merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights that vary from state to state.
ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813
Part No. 290377 R1109A
Printed in China © 2009 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|