™
CSP Series
Commercial Self-Priming Pump
Standard Features
• Cast iron construction, enclosed bronze impeller and
bronze wear rings for long lasting reliability.
For commercial and public swimming
pools and spas, aquatic facilities, water
parks and fountain applications where
high performance and self-priming
characteristics are desired.
• Exceptional self priming design with hair and lint
strainer installed – allows pumps to be installed
above or below water level.
™
Rugged, self-priming CSP Series commercial
• Oversized hair and lint strainer* with electro-polished
stainless steel basket holds a large quantity of debris.
pumps feature an enclosed bronze impeller,
standard 6" x 4" flange connections, plus a
1,100 cubic inch capacity hair and lint strainer.
Motors are standard JM type, NEMA “C” flange
design with a stainless steel shaft sleeve. These
• Available in a wide range of performance levels from
1
7 ⁄
2
to 20 HP to handle your varied pumping needs.
®
• Nationally recognized NEMA motors offer high
performance under continuous operation.
1
• Back pull-out design enables servicing of normal
wearing parts without disconnecting piping.
cast iron pumps are available in 7 ⁄2, 10, 15 and
20 HP, and may be purchased with or without
corrosion-preventing epoxy coating on all wetted
surfaces. Pump and strainer sold separately.
• Dimensionally compatible to most installations for
easier initial hook-ups or retrofits.
• Integral design base is slotted for ease of mounting.
*To insure priming and proper pump operation, install only with Sta-Rite Hair
and Lint Strainer. Order pump and strainer separately.
Pentair Water Commercial Pool and Spa™
Download from Www.Somanuals.com. All Manuals Search And Download.
CSP Commercial Pump
1/4 NPT
PLUG
19.30
16.55
(OPTIONAL
SUCTION
GAUGE
CP
6",
125 LB.
ANSI
20.27
LOCATION)
SUCTION
FLANGE
20.32
1/4 NPT PLUG
(OPTIONAL PRESSURE
GAUGE LOCATION)
3/4 - 10 UNC
x 1.60 DEEP
6.88
11.00
B
11.62
FLOW
5.225
4.25
16.38
1/2 NPT
DRAIN
PLUG
E
3/4 - 10 UNC
THRU FLANGE
(6) PLACES
T
A
8.50
D
10.45
6.25
7.68
4", 125 LB. ANSI
DISCHARGE FLANGE
R
B
9.50 BC
B
22.5°
11.00
1/2 NPT
3.44
SLOTS FOR
5/8" MOUNTING
BOLTS
19.48
DRAIN PLUG
F
4.06
7.92
15.85
S
9.00
6.00
5/8 - 11 UNC x 1.28 DEEP
(8) PLACES.
.88 THRU (8) PLACES
SECTION B - B
(VOLUTE TOP VIEW)
Outline Dimensions
Catalog Number
All dimensions shown in inches.
A
B
CP
D
E
F
G
H
I
CSPHK, CCSPHK
CSPHK3, CCSPHK3, CSPH2K3
CSPHL, CCSPHL
10.62
9.00
7.00
6.75
8.26
7.00
8.50
8.50
10.80
12.44
39.44
40.31
42.69
41.00
42.50
42.50
46.75
48.50
5.25
4.50
5.25
5.25
5.25
5.25
6.25
6.25
4.25
3.75
4.25
4.25
4.25
4.25
5.00
5.00
5.50
5.50
7.00
5.50
7.00
7.00
8.20
10.00
1.00
1.75
1.00
1.00
1.00
1.00
0.00
0.00
30.00
29.13
30.00
30.00
30.00
30.00
31.62
31.65
8.50
7.50
8.50
8.50
8.50
8.50
10.00
10.00
10.35
10.62
10.62
10.62
12.50
13.38
CSPHL3, CCSPHL3
CSPHM3, CCSPHM3
CSPH2L3, CSPH2M3
CSPHN3, CCSPHN3
CSPH2N3, CCSPH2N3
Ordering Information
Catalog
Number
Nominal
HP (kw)
Motor
Voltage
Full-Load*
Amps
Approx. Ship. Weight lbs. (kg)
(Pump Only)
Phase
CSPHK/CCSPHK
7-1/2 (5.6)
7-1/2 (5.6)
7-1/2 (5.6)
10 (7.5)
1
3
3
1
3
3
3
3
3
3
230
208-230/460
200
39
270 (122)
265 (120)
265 (120)
275 (124)
270 (122)
270 (122)
280 (127)
280 (127)
325 (148)
350 (159)
CSPHK3/CCSPHK3
CSPH2K3/CCSPH2K3
CSPHL/CCSPHL
21.7/18.0/9.8
22.1
230
46
CSPHL3/CCSPHL3
CSPH2L3/CCSPH2L3
CSPHM3/CCSPHM3
CSPH2M3/CCSPH2M3
CSPHN3/CCSPHN3
CSPH2N3/CCSPH2N3
10 (7.5)
208-230/460
200
27.6/25/12.5
28.1
10 (7.5)
15 (11.2)
15 (11.2)
20 (15)
208-230/460
200
44.2/40/20
42.3
208-230/460
200
55.3/50/25
57.3
20 (15)
*Amp draw may vary depending on motor manufacturer.
OPTIONS: CCSP Models feature special epoxy coated castings for maximum performance and corrosion resistance.
60 Hz T.E.F.C., 60 Hz premium efficiency, or 575 volt motors available, consult factory.
NOTE: Maximum ambient temperature for motor is 104°F (40°C). All pump motors require external overload protection (magnetic starter).
Pump strainer must be ordered separately (see below). Full load amps on motor model plate.
Accessory Ordering Information
Catalog
Number
Approx. Ship
Weight lbs. (kg)
Approx. Ship.
Vol. Ft3 (m3)
Description
PKG 184
Strainer for CSP/CCSP, 6" ANSI Flange (1,100 cu. in. capacity)
180 (82)
180 (82)
6.4 (.18)
6.4 (.18)
PKG 184C Strainer for CSP/CCSP, 6" ANSI Flange (1,100 cu. in. capacity), Epoxy Coated
PKG 184
Download from Www.Somanuals.com. All Manuals Search And Download.
™
CSP Series
Commercial Self-Priming Pump
neoprene to protect motor bearings from any seal leakage.
The pump shall be capable of operating at up to 75 psi, 125°F
continuous water temperature and within a pH range of 6 to 9.
ENGINEERING SPECIFICATIONS
CSP/CCSP Series Pump
• Recirculating pump shall be Sta-Rite Model No. _________
self-priming centrifugal pump, ____ phase, 60 Hz.
®
• The electric motor coupled to the pump shall be of the NEMA
series JM construction with carbon steel shaft inside a remov-
able shaft sleeve of 300 series stainless steel. The motor shall
be of an open drip-proof design (unless otherwise specified) with
permanently sealed ball bearings. Motors shall be continuous
duty rated at 40°C (or better) ambient and be suitable for outdoor
installation.
General Notes
• Install pump in a cool, dry, well vented location away from pool
heaters, and chemical storage.
• Pump should be firmly mounted with pipe supported, to prevent
vibration and undue operational noise.
• The pump motor shall be a ___ HP, ___ phase, 60 Hz, 3450 RPM
for service on a ___ volt electric supply. The pump shall be
rated for ______ GPM at ____ TDH. The pump shall be tested
and certified by a nationally recognized testing laboratory to
conform to National Sanitation Foundation Standard 50. (CCSP
models only.)
• Allow 12" minimum clearance behind motor for servicing.
• Motor overheating may be caused by a voltage drop or excessive
voltage. Be sure that wire size and voltage input is properly
regulated.
Hair and Lint Strainer
Specifications
• The pump strainer shall consist of a ______ (red brass/cast iron)
body, cover with O-ring seal, threaded locking handles, and a
strainer basket of perforated electro-polished stainless steel
basket material.
• The recirculating pump shall be a self-priming, centrifugal design
with a hair and lint strainer as shown in the plans.
• The pump body, seal plate, and attached hair and lint strainer shall
be constructed of close-grained gray iron with fusion-bonded epoxy
®
®
• The strainer body shall be 6" ANSI 125 bolt flanged with fusion-
coating of Scotchkote 134 on all wetted cast iron surfaces and
®
bonded epoxy coating of Scotchkote on all wetted cast iron
close-coupled to an electric motor by means of an adaptor of the
same material. The pump body shall have a single suction port with
surfaces unless specified for in-line mounting ahead of the pump.
The strainer body shall have a removable drain plug for winterizing.
®
a 6” ANSI 125 bolt flange to the hair and lint strainer. A centerline
®
discharge port of 4” ANSI 125 bolt flange and a winterizing drain
• The strainer basket shall be securely positioned below the
suction inlet of the trap, with access for inspection and cleaning
through a removable trap body lid. The trap body lid shall be
secured by means of threaded locking handles. The strainer
basket shall have perforations which in total area is equal to
6 times the open area of the suction pipe into the trap body inlet.
1
port of ⁄4” NPT shall be a part of the design.
• The pump shall be a back pull-out design to allow servicing with-
out disturbing piping. The pump shall have a cast iron diffuser to
aid in priming and it shall contain a replaceable bronze wear ring
for the impeller. The impeller shall be of the closed type and cast
in red brass, non-overloading at any point on the performance
• The pump strainer shall be Sta-Rite Model No. _______
®
curve. The mechanical shaft seal shall be a John Crane type 21
or equivalent and constructed of ceramic and carbon seal faces,
with stainless steel, brass and Buna N materials in the spring
bellows portion. The impeller shall be secured to the motor shaft
by means of a stainless steel key and locking screw into the end
of the motor shaft. There shall be a shaft slinger made of
Phone: 800-831-7133
Fax: 800-284-4151
1/06 Part #P1-741
©2006 Pentair Water Pool and Spa, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|