Model No. PFSY2925.0
Serial No.
Write the serial number in the
space above for future reference.
USER’S MANUAL
Serial Number Decal (Under Seat)
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if a part is
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
new products, prizes,
fitness tips, and much more!
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of serious injury, read the following important precautions
before using the resistance system.
1. Read all instructions in this manual and all
warnings on the resistance system before
using the resistance system. Use the resist-
ance system only as described in this manual.
10. Make sure that the cables remain on the pul-
leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys. Replace all
cables at least every two years.
2. It is the responsibility of the owner to ensure
that all users of the resistance system are
adequately informed of all precautions.
11. The resistance system is designed to be
used with the included resistance, and the
resistance included with a PROFORM
RECOIL Max Pack. Do not use the resistance
system with dumbbells or any other type of
resistance.
3. The resistance system is intended for home
use only. Do not use the resistance system in
any commercial, rental, or institutional setting.
4. Keep the resistance system indoors, away
from moisture and dust. Place the resistance
system on a level surface, with a mat
12. When adding resistance, both ends of the
resistance bars must rest under the two “U”-
channels. Add and remove resistance bars
from the “U”-channels one resistance bar at
a time.
beneath it to protect the floor or carpet. Make
sure that there is enough clearance around
the resistance system to mount, dismount,
and use the resistance system.
13. Keep clear of the area around the “U”-chan-
nels while the resistance system is in use.
Do not add or remove resistance bars from
the “U”-channels while the end of the long
cable is pulled out.
5. Inspect and properly tighten all parts regular-
ly. Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the resistance system at all times.
14. Pull on the cables only while sitting on the
bench or standing on the base plate.
7. Keep hands and feet away from moving
parts.
15. If you feel pain or dizziness at any time while
exercising, stop immediately and begin cool-
ing down.
8. Always wear athletic shoes for foot protec-
tion while exercising.
9. The resistance system is designed to sup-
port a maximum user weight of 300 pounds.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Thank you for selecting the versatile PROFORM®
RECOIL resistance system. The resistance system
offers a selection of stations designed to develop
every major muscle group of the body. Whether your
goal is to tone your body, build dramatic muscle size
and strength, or improve your cardiovascular system,
model number and serial number before calling. The
model number is PFSY2925.0. The serial number can
be found on a decal attached to the resistance system
(see the front cover of this manual).
To avoid a registration fee for any service needed
the resistance system will help you to achieve the spe- under warranty, you must register the resistance
cific results you want.
For your benefit, read this manual carefully before
using the resistance system. If you have questions
after reading this manual, see the front cover of this
manual. To help us assist you, please note the product
Before reading further, please review the drawing
below and familiarize yourself with the parts that are
labeled.
ASSEMBLED DIMENSIONS:
Height: 83 in. / 211 cm
Width: 60 in. / 152 cm
Depth: 48 in. / 122 cm
Pulley Housing
Handle
Upright
Short Cable
Right Side
Resistance Bars
Backrest
Seat
“U”-channel
Left Side
Leg Lever
Base
Upright Base
Squat Bar
Note: The terms “right side” and “left side” are determined relative to a person sitting on the
bench; they do not correspond to right and left on the drawings in the manual.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
• For help identifying small parts, use the PART
IDENTIFICATION CHART.
Make Things Easier for Yourself
Everything in this manual is designed to ensure
that the resistance system can be assembled
successfully by almost anyone. Most people find
that by setting aside plenty of time, assembly will
go smoothly.
• As you assemble the resistance system, make
sure all parts are oriented as shown in the draw-
ings.
• Tighten all parts as you assemble them, unless
instructed to do otherwise.
To hire an authorized service technician to
assemble the resistance system, call toll-free
1-800-445-2480.
The included hex key(s)
and the following tools (not included) may be
required for assembly:
and grease,
Before beginning assembly, carefully read the
following information and instructions:
• Two adjustable wrenches
• One rubber mallet
• Assembly requires two people.
• One standard screwdriver
• Because of its weight and size, the resistance
system should be assembled in the location
where it will be used. Make sure that there is
enough clearance to walk around the resistance
system as you assemble it.
• One Phillips screwdriver
• Clear tape or masking tape, and soapy water.
Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until assembly is completed.
1.
1
Before beginning assembly, make sure you
understand the information in the box
above. For help identifying small parts, use
the PART IDENTIFICATION CHART in the
center of this manual.
4
Attach three Plastic Feet (1) to the Base (2) with
three M4 x 16mm Screws (61).
2
Attach the Base Cover (4) to the Base (2) with
two M4 x 50mm Screws (66).
1
61
1
61
66
1
61
66
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Attach the Upright Base (5) to the Base (2) with
four M10 x 76mm Button Bolts (65) and four M10
Nylon Locknuts (56).
2
5
56
56
65
65
2
3. Identify the Left Upright (6) and the Right Upright
(7) by the “L” and “R” stickers. Attach the two
Uprights and the Rear Frame (10) to the Upright
Base (5) with two M10 x 81mm Button Bolts (68)
and two M10 Nylon Locknuts (56). Make sure
that the Bolts are inserted through the indicat-
ed holes. Do not tighten the Locknuts yet.
3
7
6
68
68
10
56
5
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Attach the two 10-pound Short Caps (81) to the
10-pound Center Bar (45) with two M4 x 12mm
Flat Head Screws (58).
4
45
49
81
58
Using ten M4 x 12mm Flat Head Screws (58),
attach the two 10-pound Caps (53) to the 10-
pound Bar (46), the two 20-pound Caps (52) to
the 20-pound Bar (47), the four 80-pound Caps
(51) to the two 80-pound Bars (48), and the two
40-pound Caps (50) to the 40-pound Bar (49).
48
48
50
47
46
58
51
58
51
58
52
58
53
58
5. Turn the Top Tray (14) upside-down. Set the
resistance bars into the Tray in the following
order: 10-pound Bar (46), 20-pound Bar (47), 80-
pound Bar (48), 10-pound Center Bar (45), 80-
pound Bar (48), and 40-pound Bar (49). Make
sure that the resistance bars are centered in
the Tray.
5
70
15
14
Set the Bottom Tray (13) on top of the Top Tray
(14) to hold the resistance bars in place. Turn the
Trays over and slide them onto the Rear Frame
(10). Make sure that the Trays and the resist-
ance bars are oriented as shown.
45
49
Have a second person attach the Trays (13 and
14) to the Rear Frame (10) with the Tray Cover
(15), two M8 x 100mm Button Bolts (70), two M8
Washers (54), and two M8 Nylon Locknuts (57).
13
10
48
47
54
57
Press the Tray Cap (16) into the Rear Frame
(10).
57
16
46
6. Refer to the CABLE DIAGRAM on page 14
while cabling the resistance system to ensure
correct cable routing. Do not overtighten the
bolts attaching the pulleys; the pulleys must
be able to turn easily.
6
59
56
82
Insert the Long Cable (42) into the indicated
Swivel Arm (12) and the Rear Frame (10). Make
sure that the Cable is below the rod in the
Swivel Arm.
10
82
42
12
Rod
59
Attach a 90mm Pulley (38) inside the Swivel Arm
(12) with an M10 x 51mm Button Bolt (74), two
M10 Washers (59), two 5mm Spacers (82), and
an M10 Nylon Locknut (56).
74
38
7
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Note: This step may be easier if the resistance
system is tipped over forward (see drawing
7b).
7a
Route the Long Cable (42) around a 90mm Pulley
(38). Insert an M10 x 132mm Button Bolt (69) into
a Finger Guard (37), a Cable Trap (39), the
Pulley, an M10 Washer (59), an 8mm Spacer
(41), another Finger Guard, and another 8mm
Spacer. Note: The end of the Bolt must be
flush with the edge of the last spacer. Make
sure that the Cable Trap is oriented to hold
the Cable in the groove of the Pulley.
42
39
38
59
41
69
37
37
See drawing 7b. Insert the 90mm Pulley (38)
inside the Rear Frame (10). Push the M10 x
132mm Button Bolt (69) through the Rear Frame
and the Left Upright (6). Finger tighten an M10
Nylon Locknut (56) onto the Bolt. Do not tighten
the Locknut yet.
7b
69
38
10
6
56
8. Wrap the Long Cable (42) under a 90mm Pulley
(38). Attach the Pulley, a Cable Trap (39), and
two Finger Guards (37) to the Base (2) with an
M10 x 47mm Button Screw (76) and an M10
Washer (59). Make sure that the Cable Trap is
oriented to hold the Cable in the groove of the
Pulley.
8
42
59
38
76
39
37
37
2
9. Attach a Pulley Bracket (17) to the indicated “U”-
channel (18) with an M10 x 129mm Button Bolt
(72), two M10 Washers (59), and an M10 Nylon
Locknut (56).
9
Wrap the Long Cable (42) over a 90mm Pulley
(38). Attach the Pulley inside the Pulley Bracket
(17) with an M10 x 41mm Button Bolt (71) and an
M10 Nylon Locknut (56).
18
56
59
56 59
71
72
17
42
38
8
Download from Www.Somanuals.com. All Manuals Search And Download.
10. Wrap the Long Cable (42) under a 90mm Pulley
(38). Attach the Pulley, a Cable Trap (39), and
two Finger Guards (37) to the Base (2) with an
M10 x 47mm Button Screw (76) and an M10
Washer (59). Make sure that the Cable Trap is
oriented to hold the Cable in the groove of the
Pulley.
10
76
42
37
Note: The Finger Guards (37) attached in this
step will overlap the Finger Guards attached
in step 8.
37
59
38
39
2
11. Route the Long Cable (42) under a 90mm Pulley
(38). Attach the Pulley, a Cable Trap (39), and
two Finger Guards (37) to the indicated hole in
the Base (2) (see the inset drawing) with an M10
x 47mm Button Screw (76) and an M10 Washer
(59). Make sure that the Cable Trap is oriented
to hold the Cable in the groove of the Pulley.
11
37
42
38
76
37
59
39
Hole
2
2
12. Attach a Pulley Bracket (17) to the indicated “U”-
channel (18) with an M10 x 129mm Button Bolt
(72), two M10 Washers (59), and an M10 Nylon
Locknut (56).
12
18
Wrap the Long Cable (42) over a 90mm Pulley
(38). Attach the Pulley inside the Pulley Bracket
(17) with an M10 x 41mm Button Bolt (71) and an
M10 Nylon Locknut (56).
72
59
59
17
56
56
42
71
38
13. Wrap the Long Cable (42) under a 90mm Pulley
(38). Attach the Pulley, a Cable Trap (39), and
two Finger Guards (37) to the Base (2) with an
M10 x 47mm Button Screw (76) and an M10
Washer (59). Make sure that the Cable Trap is
oriented to hold the Cable in the groove of the
Pulley.
13
42
76
37
37
Note: The Finger Guards (37) attached in this
step will overlap the Finger Guards attached
in steps 8 and 11.
59
38
39
2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
14. Note: This step may be easier if the resistance
system is tipped over forward (see drawing
14b).
14a
12
69
59
38
41
37
Use the wire in the Rear Frame (10) to pull the
Long Cable (42) through the Rear Frame and out
of the Swivel Arm (12). Have a second persons
hold the cable end until step 15 is completed.
41
37
39
42
Hold a 90mm Pulley (38) under the Long Cable
(42) as shown. Insert an M10 x 132mm Button
Bolt (69) into a Finger Guard (37), a Cable Trap
(39), the Pulley, an M10 Washer (59), an 8mm
Spacer (41), another Finger Guard, and another
8mm Spacer. Note: The end of the Bolt must
be flush with the edge of the last spacer. Make
sure that the Cable Trap is oriented to hold
the Cable in the groove of the Pulley.
10
42
14b
69
10
See drawing 14b. Insert the 90mm Pulley (38)
inside the Rear Frame (10). Push the M10 x
132mm Button Bolt (69) through the Rear Frame
and the Right Upright (7). Tighten an M10 Nylon
Locknut (56) onto the Bolt.
38
7
56
Tighten the M10 Nylon Locknuts (56) used in
steps 3 and 7.
15. Make sure that the Long Cable (42) is below
15
the rod in the Swivel Arm (12).
56
82
Attach a 90mm Pulley (38) inside the Swivel Arm
(12), under the Long Cable (42), with an M10 x
51mm Button Bolt (74), two M10 Washers (59),
two 5mm Spacers (82), and an M10 Nylon
Locknut (56).
59
Rod
82
59
74
12
38
42
16. Attach the Backrest (30) to the Upright Base (5)
and the Uprights (6 and 7) with four M6 x 76mm
Screw (64) and four M6 Washers (60).
16
7
6
60
64
64
60
30
60
5
10
Download from Www.Somanuals.com. All Manuals Search And Download.
17. Attach the Seat (31) to the Seat Frame (8) with
two M6 x 76mm Screws (64) and two M6
Washers (60).
17
31
Attach the Bumper (36) to the Seat Frame (8)
with an M4 x 16mm Screw (61).
35
8
Slide the Pad Tube (35) into the Seat Frame (8).
61
36
60
64
18. Grease an M10 x 62mm Button Bolt (75). Attach
the Leg Lever (9) to the Seat Frame (8) with the
Bolt and an M10 Nylon Locknut (56). Do not
overtighten the Locknut; the Leg Lever must
be able to pivot easily.
18
8
56
Grease
9
75
19. Slide four Foam Pads (32) onto the Pad Tube
(35) and the Leg Lever (9).
19
32
32
32
35
9
32
20. Set the Seat Frame (8) onto the Upright Base (5).
20
8
5
21. Make sure that all parts have been properly tight-
ened. The use of the remaining parts will be
explained in ADJUSTMENTS, beginning on the
next page.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
This section explains how to adjust the resistance system. See the EXERCISE GUIDELINES on page 15 for
important information about how to get the most benefit from your exercise program. Also, refer to the accompa-
nying exercise guide to see the correct form for each exercise.
Make sure all parts are properly tightened each time the resistance system is used. Replace any worn parts
immediately. The resistance system can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do
not use solvents.
ADJUSTING THE SEAT
Bracket
31
To use the Seat (31), first hold the Seat Frame (8) at
8
a declined angle and set the bracket onto a bar on
the Upright Base (5). Then, pivot the Seat Frame
down.
5
9
To remove the Seat (31), first make sure that the Short
Cable (not shown) is not attached to the Leg Lever
(9). Then, lift the Seat Frame (8) off the Upright Base
(5). Store the Seat away from the resistance system
while performing an exercise that does not require it.
ADJUSTING THE RESISTANCE
To add resistance, hold a “U”-channel (18) firmly and
push the end of a resistance bar under it. Repeat with
the other end of the resistance bar. If more resistance
is needed, add one resistance bar at a time.
Note: When adding resistance, always start with the
heaviest resistance bar to be used, and finish with the
lightest resistance bar. When removing resistance
bars from the “U”-channels (18), start with the lightest
resistance bar and finish with the heaviest.
Resistance
Bars
18
WARNING:
When adding resist-
ance, make sure that both ends of the resist-
ance bar rest under the two “U”-channels (18).
Do not add or remove resistance bars from
the “U”-channels while an end of the Long
Cable (42) is pulled out.
18
42
Note: The resistance system uses progressive resist-
ance. As the resistance bars begin to bend, the
amount of resistance will increase gradually. As the
resistance bars bend further, the resistance will
increase rapidly.
Additional resistance can be added to the resist-
ance system. To purchase more resistance, call our
Customer Service Department toll-free at the number
of on the front cover of this manual and ask for model
number PFMC0825 (100-pound Max Pack).
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE PULLEY HOUSINGS
7
To use a high pulley station, slide the hook on the
High Pulley Housing (19) onto the bracket on an
Upright (6 or 7). Attach the end of the Short Cable
(43) without the ball to the end of the Long Cable (42)
with a Clip (29). Attach the other high pulley in the
same manner.
19
43
6
Ball
To use a squat station, attach the Pulley Housings
(19) to the brackets on the Base (not shown).
To use the low pulley station, attach the two Pulley
Housings (19) to the bracket on the Upright Base (not
shown).
29
42
ATTACHING THE HANDLES
A Handle (26) or the Ankle Strap (not shown) can be
attached to a Short Cable (43) at the high pulley or a
squat station (see ATTACHING THE PULLEY
HOUSINGS above), or to the Long Cable (not shown),
with a Clip (29).
29
26
43
ATTACHING THE SQUAT BAR
The Squat Bar (25) can be attached to the Short
Cables (43) at the squat stations (see ATTACHING
THE PULLEY HOUSINGS above) with the two
Extension Straps (27) and four Clips (29). Adjust the
length of the Extension Straps as necessary.
25
29
27
29
43
43
13
Download from Www.Somanuals.com. All Manuals Search And Download.
ATTACHING THE LEG LEVER
To use the Leg Lever (9), first attach the seat to the
resistance system (see ADJUSTING THE SEAT on
page 12). Then, attach the pulley housings to the low
pulley station (see ATTACHING THE PULLEY
HOUSINGS on the previous page). Finally, attach the
Short Cables (43) to the Leg Lever with two Clips (29).
9
43
29
29
CABLE DIAGRAM
The cable diagram shows the proper routing of the
Long Cable (42). Use the diagram to make sure that
the cable has been assembled correctly. If the cable
has not been correctly routed, the resistance system
will not function properly and damage may occur. The
numbers show the correct route for the cable.
Long Cable (42)
7
10
9
1
2
4
8
6
3
5
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE GUIDELINES
THE FOUR BASIC TYPES OF WORKOUTS
Warming Up—Begin each workout with 5–10 minutes
of stretching and light exercise to warm up. Warming up
prepares your body for more strenuous exercise by rais-
ing your body temperature, increasing circulation, and
delivering more oxygen to your muscles.
Muscle Building—To increase muscle size, use a high
amount of resistance. Your muscles will adapt and grow
as you progressively increase the intensity of your exer-
cise by:
Working Out—Each workout should include 6–10 dif-
ferent exercises. Select exercises for every major mus-
cle group, emphasizing areas that you want to develop
most. To give balance and variety to your workouts,
vary the exercises from session to session.
• changing the level of resistance
• changing the number of repetitions or sets performed.
(A “repetition” is one complete cycle of an exercise,
such as one sit-up. A “set” is a series of repetitions.)
The proper amount of resistance for each exercise
depends upon the individual. You must gauge your lim-
its and select the amount of resistance that is right for
you. Begin with 3 sets of 8 repetitions for each exercise
you perform. When you can complete 3 sets of 12 rep-
etitions without difficulty, increase the amount of resist-
ance. Rest for 3 minutes after each set.
Schedule your workouts for the time of day when your
energy level is the highest. Each workout should be fol-
lowed by at least one day of rest. Once you find the
right schedule for you, stick with it.
Exercise Form—Maintaining proper form is an essen-
tial part of an effective exercise program. This requires
moving through the full range of motion for each exer-
cise, and moving only the appropriate parts of the body.
Exercising in an uncontrolled manner will leave you feel-
ing exhausted. The exercise guide show the correct
form for several exercises and describes how to per-
form the exercise.
Toning—Tone your muscles by using a moderate
amount of resistance and increasing the number of rep-
etitions in each set. Complete as many sets of 15–20
repetitions as possible without discomfort. Rest for 1
minute after each set.
Weight Loss—To lose weight, use a low amount of
resistance and increase the number of repetitions in
each set. Exercise for 20–30 minutes, resting for a max-
imum of 30 seconds between sets.
The repetitions in each set should be performed
smoothly and without pausing. A repetition’s exertion
stage should last about half as long as the return stroke.
Proper breathing is important. Exhale during the exer-
tion stage of each repetition and inhale during the return
stroke. Never hold your breath. Rest for a short period
of time after each set. The time depends on which type
of workout you are performing (see THE FOUR BASIC
TYPES OF WORKOUTS).
Cross Training—Cross training is an efficient way to
get a complete and well-balanced fitness program. An
example of a balanced program is:
• Strength training workouts on Monday, Wednesday,
and Friday.
• 20–30 minutes of aerobic exercise, such as riding an
exercise cycle or running on a treadmill, on Tuesday
and Thursday.
Plan to spend the first couple of weeks familiarizing
yourself with the equipment and learning the proper
form for each exercise.
• Rest from both strength training and aerobic exercise
for at least one full day each week to give your body
time to regenerate.
Cooling Down—End each workout with 5–10 minutes
of stretching. Include stretches for both your arms and
legs. Move slowly as you stretch and do not bounce.
Ease into each stretch gradually and go only as far as
you can without strain. Stretching at the end of each
workout is an effective way to increase flexibility.
PERSONALIZING YOUR EXERCISE PROGRAM
Determining the right length of time for each workout, as
well as the number of repetitions and sets completed, is
an individual matter. It is important to avoid overdoing it
during the first few months of your exercise program.
You should progress at your own pace and be sensitive
to your body’s signals. If you experience pain or dizzi-
ness at any time while exercising, stop immediately and
begin cooling down. Find out what is wrong before con-
tinuing. Remember that adequate rest and a proper diet
are important factors in any exercise program.
Staying Motivated—For motivation, keep a record of
each workout. The charts on pages 14 and 15 can be
photocopied and used to record your workouts. List
the date, the exercises performed, the resistance used,
and the numbers of sets and repetitions completed.
Record your weight and key body measurements at the
end of every month. Remember, the key to achieving
the greatest results is to make exercise a regular and
enjoyable part of your everyday life.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LIST—Model No. PFSY2925.0
R0805A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
3
1
1
1
1
1
1
1
1
1
4
2
1
1
1
1
2
2
2
4
2
2
2
2
1
2
2
1
6
1
1
4
4
3
1
1
12
10
6
2
4
1
2
Plastic Foot
Base
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
#
1
1
1
1
2
1
2
4
2
2
2
1
17
2
14
18
6
4
3
2
6
4
2
2
2
2
2
2
2
2
2
1
4
2
4
8
2
2
4
1
1
1
2
Leg Lever Cap
10-pound Center Bar
10-pound Bar
20-pound Bar
80-pound Bar
40-pound Bar
40-pound Cap
80-pound Cap
20-pound Cap
10-pound Cap
M8 Washer
Squat Pad
M10 Nylon Locknut
M8 Nylon Locknut
M4 x 12mm Flat Head Screw
M10 Washer
M6 Washer
M4 x 16mm Screw
M4 x 32mm Screw
29mm Round Cap
M6 x 76mm Screw
M10 x 76mm Button Bolt
M4 x 50mm Screw
M4 x 12mm Screw
M10 x 81mm Button Bolt
M10 x 132mm Button Bolt
M8 x 100mm Button Bolt
M10 x 41mm Button Bolt
M10 x 129mm Button Bolt
M10 x 49mm Button Bolt
M10 x 51mm Button Bolt
M10 x 62mm Button Bolt
M10 x 47mm Button Screw
Squat Bar Hook
Base Plate
Base Cover
Upright Base
Left Upright
Right Upright
Seat Frame
Leg Lever
Rear Frame
Bracket Bushing
Swivel Arm
Bottom Tray
Top Tray
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Tray Cover
Tray Cap
Pulley Bracket
“U”-channel
Pulley Housing
Pulley Guard
M6 x 12mm Flat Head Screw
Base Cap
Upright Cap
Swivel Cap
Squat Bar
Handle
Extension Straps
Ankle Strap
Clip
Backrest
Seat
Foam Pad
19mm Round Cap
38mm x 64mm Cap
Pad Tube
M5 x 16mm Screw
19mm Thick Round Cap
Retainer Ring
10-pound Cap
5mm Spacer
User’s Manual
Exercise Guide
Grease Packet
Hex Key
Bumper
Finger Guard
90mm Pulley
Cable Trap
Small Pulley
8mm Spacer
Long Cable
Short Cable
#
#
#
Note: “#” indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of the user’s manual for information about ordering replacement parts.
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Refer to the drawings below to identify small parts used in assembly. The number in parentheses by each draw-
ing is the key number of the part, from the PART LIST in the center of this manual. Note: Some small parts
may have been pre-attached. If a part is not in the parts bag, check to see if it has been pre-attached.
M4 x 50mm Screw (66)
M4 x 12mm Flat Head Screw (58)
M4 x 16mm Screw (61)
M10 x 51mm Button Bolt (74)
M10 x 47mm Button Screw (76)
M6 Washer (60)
M8 Washer (54)
M10 x 41mm Button Bolt (71)
M10 x 62mm Button Bolt (75)
M6 x 76mm Screw (64)
M10 x 76mm Button Bolt (65)
M10 Washer (59)
M10 x 81mm Button Bolt (68)
M8 x 100mm Button Bolt (70)
M8 Nylon Locknut (57)
M10 Nylon Locknut (56)
M10 x 129mm Button Bolt (72)
M10 x 132mm Button Bolt (69)
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING A—Model No. PFSY2925.0
R0805A
23
31
23
32
34
33
35
7
8
56
44
9
60
33
6
64
36
61
33
75
64
60
34
32
33
64
60
32
34
32
56
64
56
78
30
63
60
56
55
5
77
79
79
79
78
56
25
63
79
59
65
77
65
76
59
37
38
4
76
37
38
3
37
39
39
76
37
37
59
38
76
39
59
38
39
2
67
37
1
61
1
62
22
61
67
62
1
61
66
66
22
62
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWING B—Model No. PFSY2925.0
R0805A
50
51
58
58
51
52
53
58
49
58
58
48
18
50
81
58
47
58
51
58
56
58
51
11
17
38
72
46
45
58
52
56
59
71
11
59
58
73
53
20
59
18
58
19
20
56
58
17
72
71
81
40
73
59
20
59
58
56
59
19
20
11
70
56
43
40
37
59
11
15
59
56
38
16
14
13
43
41
69
37
68
39
54
38
54
59
56
57
12
82
21
41
59
82
59
74
59
68
69
29
24
80
29
39
37
41
21
38
41
37
38
10
42
80
24
26
82
56
82
59
59
74
27
12
42
28
38
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:
• the MODEL NUMBER of the product (PFSY2925.0)
• the NAME of the product (PROFORM RECOIL resistance system)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING in the
center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON), warrants this product to be free from defects in workmanship and
material, under normal use and service conditions, for a period of five (5) years from the date of purchase.
ICON warrants the resistance bars for the lifetime of the product. Shipping of the resistance bars is not
covered. Labor is covered for one year. This warranty extends only to the original purchaser. ICON's obli-
gation under this warranty is limited to replacing or repairing, at ICON's option, the product through one
of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized
by ICON. If the product is shipped to a service center, freight charges to and from the service center will
be the customer’s responsibility. For in-home service, the customer will be responsible for a minimal trip
charge. This warranty does not extend to any product or damage to a product caused by or attributable
to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON
authorized service center; products used for commercial or rental purposes; or products used as store
display models. No other warranty beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in con-
nection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of inci-
dental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the above
limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 227696 R0805A
Printed in China © 2005 ICON IP, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
|