Model No. 831.285870
Serial No.
USERÕS MANUAL
Write the serial number in the space
above for reference.
Serial Number Decal
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
SEARS, ROEBUCK AND CO., HOFFMAN ESTATES, IL 60179
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFORE YOU BEGIN
Congratulations for selecting the revolutionary PRO-
FORM¨ REBEL Recumbent Bike and Elliptical
please call our toll-free HELPLINE at 1-800-736-6879,
Monday through Saturday, 7 a.m. until 7 p.m. Central
Time (excluding holidays). To help us assist you,
please note the product model number and serial
number before calling. The model number is
831.285870. The serial number can be found on a
decal attached to the REBEL (see the front cover of
this manual).
Crosstrainer. The REBEL is an incredibly smooth
exerciser that moves your feet in a natural elliptical
path, minimizing the impact on your knees and ankles.
The unique REBEL can easily be converted from an
elliptical crosstrainer to a recumbent bike, giving you
two machines in one. Welcome to a whole new world
of natural, elliptical-motion exercise from PROFORM.
Before reading further, please look at the drawing
below and familiarize yourself with the parts that are
labeled.
For your benefit, read this manual carefully before
you use the REBEL. If you have additional questions,
The decal shown below has been placed on the
REBEL. If the decal is missing, or if it is not legible,
please call our toll-free HELPLINE at 1-800-736-6879
FRONT
to order a replacement decal. Apply the replacement
decal in the location shown.
Console
Book Holder
and Seat
Handlebar
Backrest
Lock Knob
(on back)
Upright
Resistance Knob
Side Shield
Base
Pedal
Toe Pedal
Pedal Leg
BACK
RIGHT SIDE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PART IDENTIFICATION CHART
Use the chart below to identify the small parts used in
assembly. The number in parenthesis below each part
is the key number of the part, from the PART LIST on
page 14. The number after the dash indicates the
quantity needed for assembly. Note: Some small
parts may have been pre-attached for shipping. If
a part is not in the parts bag, check to see if it has
been pre-attached.
M10 Nylon Locknut (54)Ñ6
1/2" Nylon Locknut (9)Ñ2
M10 Washer (71)Ñ6
Metal Handlebar Spacer (83)Ð2
M16 Flat Washer (84)Ñ2
Pedal Arm Spacer (42)Ñ2
Plastic Sleeve (53)Ñ2
Pedal Bolt (8)Ñ2
M4 x 38mm Screw (4)Ñ2
M10 x 68mm Bolt (67)Ð4
M4 x 16mm Tapping Screw (30)Ñ8
M10 x 75mm Bolt (66)Ð2
M6 x 16mm Seat Screw (28)Ð8
Console Mount Screw (69)Ð1
Handlebar Screw (51)Ð4
M10 x 25mm Button Head Bolt (85)Ð2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Assembly requires two persons. Place all parts of the PROFORM¨ REBEL in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
Assembly requires a phillips screwdriver
rubber mallet
, two adjustable wrenches
(none of these are included).
and a
1. Hold the Stabilizer (68) against the saddle on the back
of the Base (1). Attach the Stabilizer with two M10 x
75mm Bolts (66) and two M10 Nylon Locknuts (54).
54
1
1
54
68
66
2. Slide the Rail Stabilizer (37) onto the Base (1), so the
ÒUÓ-channel on the stabilizer fits into the Base. Make
sure the Reed Switch Wire (48) is extending from
the hole that will be formed as the two parts slide
together. Make sure you donÕt damage the Reed
Switch Wire when the two parts meet.
2
37
ÒUÓ-channel
48
Insert two M10 x 68mm Bolts (67) with two M10
Washers (71) up through the Base (1).
71
Insert two M10 x 68mm Bolts (67) with two M10
Washers (71) up through the Rail Stabilizer (37).
Note: It may be easier to insert the four Bolts by
tipping the unit on its side.
67
1
3. While one person holds the Upright (2), connect the
Extension Wire (49) coming from the Upright to the
Reed Switch Wire (48) extending from the Base (1).
Stuff any excess wire into the Upright or into the Base
(1).
3
54
54
Slide the Upright (2) onto the four M10 x 68mm Bolts
(67). Make sure you donÕt damage the wires as you
slide the Upright into place.
2
49
Hand tighten an M10 Nylon Locknut (54) onto each
M10 x 68mm Bolt (67). Tip the unit on its side and use
two wrenches to tighten the Locknuts fully.
48
1
67
5
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Connect the Seat Bar Wire (88) to the Handlebar Wire
(87).
4
7
Slide the Handlebar (7) onto the Seat Bar (6) and
attach it with the four Handlebar Screws (51). Make
sure you donÕt damage the two Wires as you tight-
en the Screws.
Pull both Grips (72) towards the Handlebar (7) until
they cover the Handlebar Screws (51).
72
51
87
88
6
51
72
5. Unscrew the Console Mount Screw (69) and slide the
Detent Ring (73) off the shaft on the Console (5).
5
69
Console
Wire
Slide the console wire through the indicated hole in the
Seat Bar (6).
6
88
Lubricate the shaft on the Console (5) with the includ-
ed grease pack. Slide the shaft into the indicated hole
in the Seat Bar (6).
73
69
Slide the Detent Ring (73) onto the console shaft and
line up the hole in the Ring with the hole in the shaft.
Secure the Console (5) with the Console Mount Screw
(69). See the inset drawing for more detail.
Lubricate
73
Plug the console wire into the Seat Bar Wire (88).
5
6. Attach the Seat (43) to the indicated brackets on the
Seat Bar (6) with four M6 x 16mm Seat Screws (28).
6
Attach the Seat Cover (35) to the Seat (43), using two
M4 x 38mm Screws (4) along the rear edge and an M4
x 16mm Tapping Screw (30) on each side.
43
6
28
4
28
30
4
30
35
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Plug the Extension Wire (49) that is coming out of the
top of the Upright (2) into the Handlebar Wire (87)
extending from the Handlebar (7).
7
Slide a Plastic Sleeve (53) onto each of the threaded
shafts on the Upright (2) as shown.
87
85
71
Note: It will be easier to perform this step if one
person holds the Handlebar in place while another
tightens the Bolts. Attach the Handlebar (7) to the
Upright (2) with the two M10 x 25mm Button Head
Bolts (85). To do this, slide an M10 Washer (71) onto
each Bolt. Slide the Bolts through the brackets on the
Handlebar. Slide an M16 Flat Washer (84) onto each
Bolt. Slide a Metal Handlebar Spacer (83) onto each
Bolt. Slide the Bolts into the threaded holes in the
Upright and tighten them with the included allen
wrench.
83
53
7
84
49
84
2
85
83
53
Threaded Shaft
71
8
Do not overtighten the Button Head Bolts (85); it
must be easy to pivot the Handlebar (7).
40
28
8. Attach the Backrest (40) to the indicated brackets on
the Upright (2) with four M6 x 16mm Seat Screws (28).
2
28
9. Identify the Left Pedal Leg (3) by looking at the
Lock Pin (90) on the pre-assembled Toe Pedal (36).
The Lock Pin must be on the outside when the
Pedal Leg is mounted.
9
Attach a Pedal (29) to the Left Pedal Leg (3) with three
M4 x 16mm Tapping Screws (30).
9
3
Lubricate a Pedal Bolt (8) with the included grease
pack and slide it through the two pre-assembled
Bushings (39). Slide a Plastic Pedal Spacer (42) onto
the Pedal Bolt (8) and slide the Bolt into the hole in the
left Crank Arm (10). Tighten a 1/2Ó Nylon Locknut (9)
onto the Pedal Bolt (8).
36
29
Repeat this procedure for the Right Pedal Leg (70, not
shown).
30
Lock Pin (90)
42
39
Lubricate
10
8
7
Download from Www.Somanuals.com. All Manuals Search And Download.
10.The Console (5) requires two ÒAAÓ batteries (not
included). Alkaline batteries are recommended.
10
Battery
Clip
Battery
Cover
To install batteries, first slide up the battery cover and
carefully remove the battery clip from the Console (5).
Insert two batteries into the battery clip as shown.
Make sure that the negative ends of the batteries
(marked ÒÐÓ) are touching the springs in the
battery clip. Replace the battery clip and close the
battery cover.
5
11.Make sure that all parts of the REBEL are properly tightened. To protect the floor or carpet from damage,
place a mat under the REBEL.
HOW TO USE THE PROFORM¨ REBEL
HOW TO SWITCH BETWEEN RECUMBENT BIKE
AND ELLIPTICAL CROSSTRAINER
To switch from elliptical crosstrainer to recumbent
bike, unscrew the Lock Knob (81, not visible). Fold
the Seat (43) down and turn the Console (5) so it is
visible when you are sitting on the Seat.
To switch from recumbent bike to elliptical crosstrain-
er, lift the Seat (43) up as far as it will go. Tighten the
Lock Knob (81, not visible) into the Upright (2). Note:
Tighten the Lock Knob fully. Push the Console (5)
in to dis-engage the lock, and then turn it so the dis-
play is visible when you are standing on the pedals.
HOW TO EXERCISE ON THE REBEL WHEN IT IS
SET UP AS AN ELLIPTICAL CROSSTRAINER
To mount the REBEL in the crosstrainer mode, hold
the handlebars and step onto the pedal that is in the
lowest position. Next, step onto the other pedal. Push
the pedals until they begin to move with a continuous
motion. Note: The crank can turn in either direc-
tion. To get the full impact of the elliptical motion,
it is recommended that you turn the crank in the
direction shown by the arrow below; however, to
give variety to your exercise, you may choose to
turn the crank in the opposite direction.
Lock Knob
5
Pedal
43
2
Crank
8
Download from Www.Somanuals.com. All Manuals Search And Download.
To dismount the REBEL, allow the pedals to slowly
come to a stop. CAUTION: The REBEL does not
have a freewheel; the pedals will continue to
move until the flywheel stops. When the pedals are
stationary, step off the highest pedal first. Then, step
off the lowest pedal.
Thumb
Pulse
Sensor
HOW TO ADJUST THE TOE PEDALS
To adjust the Right Toe Pedal (89), pull out the Lock
Pin (90). Slide the Toe Pedal forwards or backwards
to the desired location. Push the Lock Pin through the
holes in the Toe Pedal and the adjustment holes in
the Pedal Leg (70). Adjust the Left Pedal (36, not
shown) in the same manner.
LCD
Display
SpeedÑThis mode displays your pedaling speed, in
miles per hour.
TimeÑThis mode displays the elapsed time. Note:
When you stop exercising, the time mode will pause.
DistanceÑThis mode displays the total distance you
have pedaled, in miles.
89
70
90
Fat Calorie
ÑThis mode displays the approximate
number of fat calories you have burned (see BURN-
ING FAT on page 12).
HOW TO ADJUST THE RESISTANCE OF
THE PEDALS
CalorieÑThis mode displays the approximate number
of Calories you have burned.
As you exercise,
you can adjust the
resistance of the
ScanÑThis mode displays the speed, time, distance,
fat calorie and calorie modes, for 5 seconds each, in
a repeating cycle.
Resistance Knob
pedals with the
resistance knob
located as shown
here. To increase
the resistance, turn
the knob clock-
wise; to decrease
the resistance, turn
the knob counter-
clockwise.
PulseÑThis mode displays your heart rate when the
pulse sensor is used.
HOW TO OPERATE THE CONSOLE
If there is a thin sheet of clear plastic on the face of
the console, remove it.
1. To turn on the power, press the on/reset button or
simply begin pedaling. When the power is turned
on, the entire display will appear for two seconds.
The console will then be ready for operation.
DESCRIPTION OF THE CONSOLE
The console is designed to help you get the most
from your workouts. As you exercise, you can watch
your progress as the display provides continuous
exercise feedback. You can even measure your heart
rate using the built-in pulse sensor. The modes of the
display are described below. Note: Before the con-
sole can be operated, two ÒAAÓ batteries must be
installed (see assembly step 10 on page 8).
2. Select one of the modes:
Scan modeÑWhen the power is turned on, the
scan mode will automatically be selected. One
mode indicator will show that the scan mode is
selected, and a flashing mode indicator will show
9
Download from Www.Somanuals.com. All Manuals Search And Download.
which mode is
currently dis-
will appear in the display
and your pulse will be
played. Note: If
a different
mode is select-
ed, you can
shown. Hold your thumb
on the sensor for another
15 seconds for the most
accurate reading. If the
select the scan
mode again by
repeatedly
displayed pulse appears
to be too high or too low,
or if your pulse is not dis-
played, lift your thumb off
the sensor and allow the
display to reset. Press
Mode Indicators
pressing the mode button.
Speed, time, distance, fat calorie or calorie
modeÑTo select one of these modes for continu-
ous display, press the mode button repeatedly. The
mode indicators will show which mode is selected.
(Make sure that the scan mode is not selected.)
down again on the sensor as described above.
Make sure that your thumb is positioned as shown,
and that you are applying the proper amount of
pressure to the pulse sensor. Try the sensor several
times until you become familiar with it.
3. To measure your pulse, stop pedaling and place
your thumb on the pulse sensor as shown. The
pulse sensor is pressure-activatedÑfully press
down the pulse sensor. Do not press too hard, or
the circulation in your thumb will be restricted,
and your pulse will not be detected. Next, slightly
raise your thumb until the heart-shaped indicator in
the LCD display flashes steadily. Hold your thumb
at this level. After 5 to 10 seconds, three dashes
4. To reset the display, press the on/reset button.
5. The console has an Òauto-offÓ feature. If the
pedals are not moved and the console buttons
are not pressed for four minutes, the power will
turn off automatically to conserve the batteries.
MAINTENANCE
CONSOLE TROUBLE-SHOOTING
unscrew the three M4 x 38mm Screws (4) from the
lower edge of the Right Side Shield. Remove the 1/2Ó
Nylon Locknut (9), Pedal Bolt (8) and Plastic pedal
Spacer (42) from the Right Pedal Leg (70, not shown).
Gently pull the Right Side Shield over the Crank Arm.
If the console does not function properly, the batteries
should be replaced. To replace the batteries, see
assembly step 10 on page 8. In addition, make sure
that the console wire is connected to the seat bar
wire. See assembly step 5 on page 6.
11
4
27
HOW TO REMOVE THE SIDE SHIELDS
For all of the following steps, one or both Side
Shields (11 and 27) must be removed.
4
4
To remove the Left Side Shield (11), unscrew the 1/2Ó
Nylon Locknut (9) and remove the Pedal Bolt (8) and
the Plastic Pedal Spacer (42) from the Left Pedal Leg
(3). Unscrew the seven M4 x 38mm Screws (4) from
the Left Side Shield. Gently pull the Left Side Shield
out and to the side, so the Crank Arm (10) fits
through the hole in the Side Shield.
42
9
3
10
4
8
4
To remove the Right Side Shield (27), first remove the
Left Side Shield (11) as described above. Then
10
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ADJUST THE REED SWITCH
HOW TO ADJUST THE DRIVE BELT
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, the Left Side Shield (11) must first be removed
as described on page 10.
If the Drive Belt (32) slips as you exercise on the
REBEL, the Drive Belt should be adjusted. To adjust the
Drive Belt, both Side Shields (11 and 27, not shown)
must first be removed as described on page 10.
Next, locate the
Reed Switch
(48). Turn the
Pulley (19) until
the Magnet (55)
Next, loosen the
two M8 Flange
Nuts (23) (there
is one on each
side of the
20
32
26
55
is aligned with
the Reed Switch.
Loosen, but do
not remove, the
M4 x 12mm
Screw (51,
shown removed
for clarity). Slide the Reed Switch slightly toward or
away from the Magnet. Make sure that the Magnet will
not hit the Reed Switch. Retighten the Screw. Turn the
Flywheel (20)).
To tighten the
Drive Belt (32),
turn the two M6
Nuts (26) clock-
wise; to loosen
the Drive Belt,
turn the M6 Nuts
51
48
23
19
counterclockwise. Make sure that the Flywheel is
straight and retighten the M8 Flange Nuts (23). When
Pulley (19) for a moment. Repeat until the console dis- the Drive Belt is properly adjusted, re-attach the Side
Shields.
plays correct feedback. When the Reed Switch is cor-
rectly adjusted, re-attach the Left Side Shield (11).
HOW TO TIGHTEN THE CRANK
HOW TO ADJUST THE RESISTANCE STRAP
If the Crank Arms (10) become loose, they should be
tightened in order to prevent excessive wear. To tight-
en the Crank Arms, the Left Side Shield (11, not
shown) must first be removed as described on page 10.
If the pedals do
not have enough
resistance, even
when the resis-
tance knob is
turned to the maxi-
mum setting, the
Resistance Strap
(31) may need to
be adjusted. To
adjust the
20
74
Next, loosen the
Crank Nut (17)
on the left
31
Crank Arm (10).
15
Place the end
of a standard
screwdriver in
one of the slots
10
Resistance Strap,
the Left Side
Shield (11, not shown) must first be removed, as
described on page 10.
in the Slotted
Crank Nut (15).
17
Lightly tap the
screwdriver with
a hammer to
turn the Slotted Crank Nut counterclockwise until the
arms are no longer loose. Do not overtighten the
Slotted Crank Nut. When the Slotted Crank Nut is
properly tightened, retighten the Crank Nut and re-
attach the Left Side Shield.
Turn the resistance knob to the lowest setting (see
HOW TO ADJUST THE RESISTANCE OF THE
PEDALS on page 9). Open the Buckle (74) and pull
the end of the Resistance Strap (31) slightly down-
ward. Close the Buckle and turn the Flywheel (20) to
make sure that there is not too much resistance.
When the Resistance Strap is properly adjusted, re-
attach the Left Side Shield.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
CONDITIONING GUIDELINES
The following guidelines will help you to plan your
exercise program. Remember that proper nutrition and
adequate rest are essential for successful results.
The proper intensity level can be found by using your
heart rate as a guide. For effective exercise, your heart
rate should be maintained at a level between 70% and
85% of your maximum heart rate as you exercise. This
is known as your training zone. You can find your train-
ing zone in the table below. Training zones are listed
according to age and physical condition.
WARNING: Before beginning this or any exercise
program, consult your physician. This is especial-
ly important for individuals over the age of 35 or
individuals with pre-existing health problems.
Burning Fat
WARNING: The pulse sensor is not a medical
device. Various factors, including the user's move-
ment, may affect the accuracy of heart rate read-
ings. The pulse sensor is intended only as an
exercise aid in determining heart rate trends in
general.
To burn fat effectively, you must exercise at the proper
intensity level for a sustained period of time. During
the first few minutes of exercise, your body uses easi-
ly accessible carbohydrate calories for energy. Only
after the first few minutes does your body begin to use
stored fat calories for energy. If your goal is to burn
fat, keep your heart rate in the lower end of your train-
ing zone.
WHY EXERCISE?
Exercise has proven essential for good health and
well-being. Participation in a well-rounded exercise
program helps to develop a stronger and more effi-
cient heart, improved respiratory function, increased
stamina, better weight management, increased ability
to handle stress, and greater self-esteem.
Aerobic Exercise
If your goal is to strengthen your cardiovascular sys-
tem, your exercise must be Òaerobic.Ó Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For effective aerobic
exercise, keep your heart rate in the higher end of
your training zone.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
HOW TO MEASURE YOUR HEART RATE
TRAINING ZONE (BEATS/MIN.)
To measure your heart rate, follow the procedure
described on page 10.
AGE UNCONDITIONED CONDITIONED
20
25
30
35
40
45
50
55
60
65
70
75
80
85
138Ð167
136Ð166
135Ð164
134Ð162
132Ð161
131Ð159
129Ð156
127Ð155
126Ð153
125Ð151
123Ð150
122Ð147
120Ð146
118Ð144
133Ð162
132Ð160
130Ð158
129Ð156
127Ð155
125Ð153
124Ð150
122Ð149
121Ð147
119Ð145
118Ð144
117Ð142
115Ð140
114Ð139
WORKOUT GUIDELINES
A proper workout includes the following parts:
A warm-up, consisting of 5 to 10 minutes of stretching
and light exercise. A proper warm-up increases the
body temperature, heart rate, and circulation in prepa-
ration for exercise.
A cardiovascular exercise period, including 20 to
30 minutes of exercise with your heart rate in your
training zone.
A cool-down, with 5 to 10 minutes of stretching.
Thorough stretching helps to offset problems caused
when you stop exercising suddenly. Stretching after
exercise is also very effective for increasing flexibility.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EXERCISE FREQUENCY
To maintain or improve your condition, plan three
workouts each week, with at least one day of rest
between workouts. After a few months of regular
exercise, you may complete up to five workouts each
week, if desired. Find the best time of day for your
workouts, and then stick with it.
SUGGESTED STRETCHES
1
The correct form for several basic stretches is shown at the
right. Move slowly as you stretchÑnever bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward
from your hips. Allow your back and shoulders to relax as you
reach down toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Hamstrings,
back of knees and back.
2
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot
toward you and rest it against the inner thigh of your extended
leg. Reach toward your toes as far as possible. Hold for 15
counts, then relax. Repeat 3 times for each leg. Stretches:
Hamstrings, lower back and groin.
3
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place
your hands against a wall. Keep your back leg straight and
your back foot flat on the floor. Bend your front leg, lean for-
ward and move your hips toward the wall. Hold for 15 counts,
then relax. Repeat 3 times for each leg. To cause further
stretching of the achilles tendons, bend your back leg as well.
Stretches: Calves, achilles tendons and ankles.
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and
grasp one foot with your other hand. Bring your heel as close
to your buttocks as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Quadriceps and hip
muscles.
5
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees out-
ward. Pull your feet toward your groin area as far as possible.
Hold for 15 counts, then relax. Repeat 3 times. Stretches:
Quadriceps and hip muscles.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
PART LISTÑMODEL No. 831.285870
R1298A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
1
1
1
12
1
1
1
2
2
2
1
2
2
1
1
1
2
2
1
1
1
3
2
2
2
2
1
8
2
9
1
1
1
1
1
1
1
2
4
1
1
2
1
2
1
1
Base
Upright
Left Pedal Leg
M4 x 38mm Screw
Console
Seat Bar
Handlebar
Pedal Bolt
1/2Ó Nylon Locknut
Crank Arm
Left Side Shield
Crank Bearing
Bearing Cup
Keyed Washer
Slotted Crank Nut
Tri-notch Crank Nut
Crank Nut
5/16Ó x 3/4Ó Tap Screw
Pulley
Flywheel w/Hub
Flywheel Axle
M10 Flat Washer
M10 Nut
M6 Eyebolt
Adjustment Bracket
M6 Nut
Right Side Shield
M6 x 16mm Seat Screw
Pedal
M4 x 16mm Tapping Screw
Resistance Strap
Drive Belt
Resistance Cable w/Spring
Resistance Knob
Seat Cover
Left Toe Pedal
Rail Stabilizer
Rail Endcap
Bushing
Backrest
Small Spring
Plastic Pedal Spacer
Seat
1 1/2Ó x 2 1/2Ó Inner Cap
Console Axle
Console Spring
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
#
4
1
1
1
4
1
2
6
1
1
4
1
1
2
2
2
1
1
2
2
4
1
3
1
6
2
1
1
2
4
4
4
2
2
1
1
2
2
2
1
1
1
1
2
1
1
Stabilizer Endcap
Reed Switch/Sensor Wire
Extension Wire
Reed Switch Clip
Handlebar Screw
M4 x 16mm Flat Head Screw
Plastic Sleeve
M10 Nylon Locknut
Magnet
Clamp Bolt
1/4Ó Flat Washer
1/4Ó Nylon Locknut
Resistance Strap Hook
Console Washer
Flywheel Bearing
Crank Cover
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Seat Cap
Bearing Washer
Crank Washer
M10 x 75mm Bolt
M10 x 68mm Bolt
Stabilizer
Console Mount Screw
Right Pedal Leg
M10 Washer
Grip
Detent Ring
Buckle
M8 x 57mm Bolt
M8 Washer
Metal Wheel Spacer
Wheel Bearing
Pedal Wheel
M8 Nylon Locknut
Lock Knob
Upright Cap
Metal Handlebar Spacer
M16 Flat Washer
M10 x 25mm Button Head Bolt
Allen Wrench
Handlebar Wire
Seat Bar Wire
Right Toe Pedal
Lock Pin
Grease Pack
#
UserÕs Manual
Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. See the back cover
of this manual for information about ordering replacement parts.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLODED DRAWINGÑModel No. 831.285870
R1298A
15
Download from Www.Somanuals.com. All Manuals Search And Download.
ORDERING REPLACEMENT PARTS
The model number and serial number of your PROFORM¨
REBEL Recumbent Bike and Elliptical Crosstrainer are listed on
a decal attached to the frame. See the front cover of this manual
to find the location of the decal.
All replacement parts are available for immediate purchase or
special order when you visit your nearest SEARS Service Center.
To request service or to order parts by telephone, call the toll-free
numbers listed at the left.
QUESTIONS?
If you find that:
When requesting help or service, or ordering parts, please be
prepared to provide the following information:
¥ you need help assembling or
operating the PROFORM¨
REBEL Recumbent Bike and
Elliptical Crosstrainer
¥ The MODEL NUMBER of the product (831.285870).
¥ The NAME of the product (PROFORM¨ REBEL Recumbent
Bike and Elliptical Crosstrainer).
¥ a part is missing
¥ or you need to schedule repair
service
¥ The KEY NUMBER and DESCRIPTION of the PART (see
pages 14 and 15).
call our toll-free HELPLINE
1-800-736-6879
MondayÐSaturday, 7 amÐ7 pm
Central Time (excluding holidays)
REPLACEMENT
PARTS
If parts become worn and need to
be replaced, call the following toll-
free number
1-800-FON-PART (366-7278)
FULL 90 DAY WARRANTY
For 90 days from the date of purchase, if failure occurs due to defect in material or workmanship in this
SEARS EXERCISER, contact the nearest SEARS Service Center throughout the United States and
SEARS will repair or replace the EXERCISER, free of charge.
This warranty does not apply when the EXERCISER is used commercially or for rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
SEARS, ROEBUCK AND CO., DEPT. 817WA, HOFFMAN ESTATES, IL 60179
PROFORM is a registered trademark of ICON Health & Fitness, Inc.
Part No. 151678 H04109AC R1298A
Printed in China © 1998 Sears, Roebuck and Co.
Download from Www.Somanuals.com. All Manuals Search And Download.
|