Pioneer Car Stereo System DEH 1590UB User Manual

CD RDS RECEIVER

DEH-1590UB

Owner’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Operating this unit

Display indication

Basic operations

CLOCK SET (setting the clock)

Indicator

State

Important

Turn M.C. to adjust hour.

Tuner: band and fre-

quency

Handle gently when removing or attaching

the front panel.

Avoid subjecting the front panel to excessive

shock.

Keep the front panel out of direct sunlight

and high temperatures.

To avoid damaging the device or vehicle inte-

rior, remove any cables and devices attached

to the front panel before detaching it.

Press M.C. to select minute.

Turn M.C. to adjust minute.

Press M.C. to confirm the selection.

RDS: program service

name, PTY information

and other literal informa-

tion

CD player and USB stor-

age device: elapsed play-

back time and text

information

Main infor-

mation sec-

tion

FM STEP (FM tuning step)

Normally, the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

Indicator

(list)

State

The list function is being oper-

ated.

Appears when a lower tier of

folder or menu exists.

The tuning step remains at 50 kHz during man-

ual tuning.

Turn M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

Sub infor-

mation sec- Sub information is displayed.

tion

TA (traffic

Set up menu

When you turn the ignition switch to ON after in-

stallation, set up menu appears on the display.

You can set up the menu options below.

Press M.C. to confirm the selection.

announce-

ments)

TA function is on.

MW STEP (MW tuning step)

The MW tuning step can be switched between

9 kHz and 10 kHz.

TP (traffic

program

identifica-

tion)

A TP station is tuned in.

Turn M.C. to select the MW tuning step.

9 (9 kHz)—10 (10 kHz)

Press M.C. to confirm the selection.

QUIT appears.

After installation of this unit, turn the

ignition switch to ON.

SET UP appears.

The sound retriever function

is on.

(sound re-

triever)

Turn M.C. to switch to YES.

If you do not operate for 30 seconds, the set up

YES.

To finish your settings, turn M.C. to select

LOC

Local seek tuning is on.

menu will not be displayed.

If you prefer not to set up at this time, turn M.C.

to switch to NO. Press to select.

If you select NO, you cannot set up in the set up

menu.

If you prefer to change your setting again, turn

(repeat) Track or folder repeat is on.

M.C. to switch to NO. Press to select.

(ran-

dom)

Random play is on.

Press M.C. to select.

Notes

Press M.C. to select.

You can set up the menu options from the

system menu. For details about the settings,

refer to System menu on page 7.

You can cancel set up menu by pressing

SRC/OFF.

Perform the following procedures to set

the menu.

To proceed to the next menu option, you need to

confirm your selection.

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Operating this unit

Frequently used menu

operations

Removing the front panel to protect your unit from

theft

Selecting a source

WARNING

Press SRC/OFF to cycle between:

TUNER (tuner)—CD (CD player)—USB (USB)

—AUX (AUX)

Keep the battery out of the reach of children.

Should the battery be swallowed, consult a

doctor immediately.

Batteries (battery pack or batteries installed)

must not be exposed to excessive heat such

as sunshine, fire or the like.

Press the detach button to release the front

panel.

Returning to the previous display

Returning to the previous list (the folder one level

higher)

Push the front panel upward (M) and then pull

it toward (N) you.

Adjusting the volume

Turn M.C. to adjust the volume.

Press /DIMMER.

Returning to the ordinary display

Canceling the main menu

CAUTION

For safety reasons, park your vehicle when re-

moving the front panel.

CAUTION

Press BAND.

Returning to the ordinary display from the list

Press BAND.

Use one CR2025 (3 V) lithium battery.

Remove the battery if the remote control is

not used for a month or longer.

There is a danger of explosion if the battery is

incorrectly replaced. Replace only with the

same or equivalent type.

Do not handle the battery with metallic tools.

Do not store the battery with metallic ob-

jects.

Always keep the detached front panel in a pro-

tection device such as a protection case.

Note

When this unit’s blue/white lead is connected to

the vehicle’s auto-antenna relay control termi-

nal, the vehicle’s antenna extends when this

unit’s source is turned on. To retract the anten-

na, turn the source off.

Re-attaching the front panel

Tuner

Slide the front panel to the left.

Make sure to insert the tabs on the left side of

the head unit into the slots on the front panel.

Basic operations

If the battery leaks, wipe the remote control

completely clean and install a new battery.

When disposing of used batteries, comply

with governmental regulations or environ-

mental public institutions’ rules that apply in

your country/area.

Selecting a band

Use and care of the remote

control

Press BAND until the desired band (FM1,

FM2, FM3 for FM, MW or SW1, SW2 for short-

wave) is displayed.

Using the remote control

Switching preset stations

Point the remote control in the direction of the

front panel to operate.

Press c or d.

Press the right side of the front panel until it is

firmly seated.

Important

Select PCH (preset channel) under SEEK to

use this function. For details about the set-

tings, refer to SEEK (left/right key setting) on

page 6.

When using for the first time, pull out the film

protruding from the tray.

Do not store the remote control in high tem-

peratures or direct sunlight.

The remote control may not function properly

in direct sunlight.

Do not let the remote control fall onto the

floor, where it may become jammed under

the brake or accelerator pedal.

If you cannot attach the front panel to the

head unit successfully, make sure that you are

placing the front panel onto the head unit cor-

rectly. Forcing the front panel into place may

result in damage to the front panel or head

unit.

Replacing the battery

Slide the tray out on the back of the remote

control.

Insert the battery with the plus (+) and minus

(–) poles aligned properly.

Turning the unit on

Press SRC/OFF to turn the unit on.

Turning the unit off

Press and hold SRC/OFF until the unit turns

off.

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Operating this unit

Notes

PTY list

Manual tuning (step by step)

BSM (best stations memory)

If the program service name cannot be ac-

Press c or d.

BSM (best stations memory) automatically stores

the six strongest stations in the order of their sig-

nal strength.

quired in FREQUENCY, the broadcast fre-

quency is displayed instead. If the program

service name is detected, the program serv-

ice name will be displayed.

NEWS/INFO (news and information)

Select MAN (manual tuning) under SEEK to

use this function. For details about the set-

tings, refer to SEEK (left/right key setting) on

the next page.

NEWS (News), AFFAIRS (Current affairs), INFO

(Information), SPORT (Sports), WEATHER (Weath-

er), FINANCE (Finance)

Press M.C. to turn BSM on.

To cancel, press M.C. again.

BRDCST INFO text information will change

automatically.

Depending on the band, text information can

be changed.

Text information items that can be changed

depend on the area.

Seeking

Press and hold c or d, and then release.

POPULAR (popular)

REGION (regional)

POP MUS (Popular music), ROCK MUS (Rock

music), EASY MUS (Easy listening), OTH MUS

(Other music), JAZZ (Jazz), COUNTRY (Country

music), NAT MUS (National music), OLDIES

(Oldies music), FOLK MUS (Folk music)

You can cancel seek tuning by briefly pressing

c or d.

While pressing and holding c or d, you can

skip stations. Seek tuning starts as soon as

you release c or d.

When AF is used, the regional function limits the

selection of stations to those broadcasting region-

al programs.

Press M.C. to turn the regional function on or

off.

Using PTY functions

You can tune in to a station using PTY (program

type) information.

CLASSICS (classics)

LOCAL (local seek tuning)

Note

L. CLASS (Light classical), CLASSIC (Classical)

OTHERS (others)

This unit’s AF (alternative frequencies search)

function can be turned on and off. AF should be

off for normal tuning operation (refer to AF (al-

ternative frequencies search) on this page).

Local seek tuning lets you tune in to only those

radio stations with sufficiently strong signals for

good reception.

Searching for an RDS station by PTY information

You can search for general types of broadcasting

programs, such as those listed in the following

section. Refer to this page.

EDUCATE (Education), DRAMA (Drama), CUL-

TURE (Culture), SCIENCE (Science), VARIED (Var-

ied), CHILDREN (Children’s), SOCIAL (Social

affairs), RELIGION (Religion), PHONE IN (Phone

in), TOURING (Travel), LEISURE (Leisure), DOCU-

MENT (Documentaries)

Press M.C. to select the desired setting.

FM: OFF—LV1—LV2—LV3—LV4

Storing and recalling stations

for each band

MW/shortwave: OFF—LV1—LV2

Press

(list).

The highest level setting allows reception of

only the strongest stations, while lower levels

allow the reception of weaker stations.

Turn M.C. to select a program type.

NEWS/INFO—POPULAR—CLASSICS—

OTHERS

Using preset tuning buttons

When you find a station that you want

TA (traffic announcement standby)

Press M.C. to begin the search.

to store in memory, press one of the preset

tuning buttons (1/ to 6/ ) and hold until

the preset number stops flashing.

Function settings

The unit searches for a station broadcasting

that type of program. When a station is found,

its program service name is displayed.

Press M.C. to turn traffic announcement

Press M.C. to display the main menu.

standby on or off.

To cancel the search, press M.C. again.

The program of some stations may differ

from that indicated by the transmitted PTY.

If no station is broadcasting the type of

program you searched for, NOT FOUND is

displayed for about two seconds and then

the tuner returns to the original station.

AF (alternative frequencies search)

Turn M.C. to change the menu option

Press one of the preset tuning buttons

and press to select FUNCTION.

Turn M.C. to select the function.

(1/ to 6/ ) to select the desired station.

Press M.C. to turn AF on or off.

NEWS (news program interruption)

Switching the display

Once selected, the following functions can be

adjusted.

Press M.C. to turn the NEWS function on or

Selecting the desired text information

If MW, SW1 or SW2 is selected, only BSM,

off.

Press DISP/DISP OFF to cycle between the fol-

lowing:

LOCAL and SEEK are available.

FREQUENCY (program service name or

frequency)

BRDCST INFO (program service name/PTY

information)

CLOCK (source name and clock)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Operating this unit

Depending on the version of iTunes used to

write MP3 files to a disc or media file types,

incompatible text stored within an audio file

may be displayed incorrectly.

Text information items that can be changed

depend on the media.

Operations using special buttons

SEEK (left/right key setting)

Switching between compressed audio and CD-DA

Press BAND.

You can assign a function to the left and right keys

of the unit.

Select MAN (manual tuning) to tune up or down

manually or select PCH (preset channel) to switch

between preset channels.

Selecting a repeat play range

Switching between playback memory devices

You can switch between playback memory devices

on USB storage devices with more than one Mass

Storage Device-compatible memory device.

Press 6/

to cycle between the following:

CD/CD-R/CD-RW

ALL – Repeat all tracks

ONE – Repeat the current track

FLD – Repeat the current folder

Press M.C. to select MAN or PCH.

Press BAND.

Selecting and playing files/

tracks from the name list

You can switch between up to 32 different

memory devices.

USB storage device

ALL – Repeat all files

ONE – Repeat the current file

FLD – Repeat the current folder

Press

to switch to the file/track name

CD/CD-R/CD-RW and USB

storage devices

Note

list mode.

Disconnect USB storage devices from the unit

when not in use.

Playing tracks in random order

Use M.C. to select the desired file name

Basic operations

Press 5/

to turn random play on or off.

(or folder name).

Tracks in a selected repeat range are played in

random order.

To change songs during random play, press d

to switch to the next track. Pressing c restarts

playback of the current track from the begin-

ning of the song.

Switching the display

Playing a CD/CD-R/CD-RW

Selecting a file or folder

Insert the disc into the disc loading slot with

the label side up.

Turn M.C.

Selecting the desired text information

Press DISP/DISP OFF to cycle between the fol-

Playing

Ejecting a CD/CD-R/CD-RW

Press h.

lowing:

CD-DA

When a file or track is selected, press M.C.

Viewing a list of the files (or folders) in the se-

lected folder

ELAPSED TIME (track number and play-

back time)

CLOCK (source name and clock)

SPEANA (spectrum analyzer)

Pausing playback

Press 4/PAUSE to pause or resume.

Playing songs on a USB storage device

Open the USB port cover.

When a folder is selected, press M.C.

Playing a song in the selected folder

When a folder is selected, press and hold M.C.

Plug in the USB storage device using a USB

cable.

Enhancing compressed audio and restoring rich

sound (sound retriever)

CD-TEXT

Playback is performed automatically.

Press 3/S.Rtrv to cycle between:

1—2—OFF (off)

TRACK INFO (track title/track artist/disc

title)

ELAPSED TIME (track number and play-

back time)

CLOCK (source name and clock)

SPEANA (spectrum analyzer)

Stopping playback of files on a USB storage de-

vice

1 is effective for low compression rates, and 2

is effective for high compression rates.

You may disconnect the USB storage device at

any time.

The unit stops playback.

Function settings

MP3/WMA/WAV

Selecting a folder

Press 1/ or 2/

Press M.C. to display the main menu.

TRACK INFO (track title/artist name/album

title)

Selecting a track

Press c or d.

Turn M.C. to change the menu option

FILE INFO (file name/folder name)

ELAPSED TIME (track number and play-

back time)

CLOCK (source name and clock)

SPEANA (spectrum analyzer)

and press to select FUNCTION.

Once selected, the function below can be ad-

justed.

Fast forwarding or reversing

Press and hold c or d.

When playing compressed audio, there is no

sound during fast forward or reverse.

Notes

TRACK INFO and FILE INFO text information

will change automatically.

Returning to root folder

Press and hold BAND.

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Operating this unit

S.RTRV (sound retriever)

This unit is equipped with a subwoofer output

which can be turned on or off.

SLA (source level adjustment)

Press M.C. to display the setting mode.

Turn M.C. to adjust the left/right speaker bal-

ance.

Automatically enhances compressed audio and

restores rich sound.

SLA (Source level adjustment) lets you adjust the

volume level of each source to prevent radical

changes in volume when switching between sour-

ces.

Press M.C. to select the desired setting.

NOR (normal phase)—REV (reverse phase)—

OFF (subwoofer off)

Press M.C. to select the desired setting.

For details, refer to Enhancing compressed

audio and restoring rich sound (sound retriever)

on the previous page.

EQ SETTING (equalizer recall)

SUB.W CTRL (subwoofer adjustment)

Settings are based on the FM volume level,

which remains unchanged.

The MW volume level can also be adjusted

with this function.

When selecting FM as the source, you cannot

switch to SLA.

Press M.C. to display the setting mode.

Turn M.C. to select the equalizer.

Only frequencies lower than those in the selected

range are outputted from the subwoofer.

POWERFUL—NATURAL—VOCAL—CUS-

TOM1—CUSTOM2—FLAT—SUPER BASS

The equalizer band and equalizer level can be

customized when CUSTOM1 or CUSTOM2 is

selected.

If selecting CUSTOM1 or CUSTOM2, complete

the procedures outlined below. If selecting

other options, press M.C. to return to the pre-

vious display.

Press M.C. to display the setting mode.

Press M.C. to cycle between the following:

Cut-off frequency—Output level—Slope level

Rates that can be adjusted will flash.

Turn M.C. to select the desired setting.

Cut-off frequency: 50HZ—63HZ—80HZ—

100HZ—125HZ—160HZ—200HZ

Output level: –24 to +6

Audio adjustments

Press M.C. to display the main menu.

Press M.C. to display the setting mode.

Turn M.C. to adjust the source volume.

Adjustment range: +4 to –4

Turn M.C. to change the menu option

and press to select AUDIO.

Turn M.C. to select the audio function.

CUSTOM1 can be set separately for each

source.

System menu

Slope level: –6— –12

Once selected, the following audio functions

can be adjusted.

Press M.C. to display the main menu.

BASS BOOST (bass boost)

CUSTOM2 is a shared setting used in com-

mon for all sources.

FADER is not available when SUB.W/SUB.W

is selected in SP-P/O MODE. For details, refer

to SP-P/O MODE (rear output and preout set-

ting) on the next page.

Press M.C. to display the setting mode.

Turn M.C. to select a desired level.

0 to +6 is displayed as the level is increased or

decreased.

Turn M.C. to change the menu option

Press M.C. to display the setting mode.

Press M.C. to cycle between the following:

Equalizer band—Equalizer level

Turn M.C. to select the desired setting.

Equalizer band: 80HZ—250HZ—800HZ—

2.5KHZ—8KHZ

Equalizer level: +6 to –6

You can also switch the equalizer by pressing

repeatedly.

and press to select SYSTEM.

3 Turn M.C. to select the system menu

SUB.W, SUB.W CTRL and HPF SETTING are

not available when REAR/REAR is selected in

SP-P/O MODE. For details, refer to

function.

HPF SETTING (high pass filter adjustment)

Once selected, the following system menu func-

tions can be adjusted.

When you do not want low sounds from the sub-

woofer output frequency range to play from the

front or rear speakers, turn on the HPF (high pass

filter). Only frequencies higher than those in the

selected range are output from the front or rear

speakers.

SP-P/O MODE (rear output and preout set-

ting) on the next page.

SUB.W CTRL and HPF SETTING are not avail-

able when SUB.W is selected in OFF. For de-

tails, refer to SUB.W (subwoofer on/off

setting) on this page.

CLOCK SET (setting the clock)

LOUDNESS (loudness)

Press M.C. to display the setting mode.

Press M.C. to select the segment of the clock

display you wish to set.

Loudness compensates for deficiencies in the low-

frequency and high-frequency ranges at low vol-

ume.

Press M.C. to display the setting mode.

Press M.C. to cycle between the following:

Cut-off frequency—Slope level

Hour—Minute

FADER (fader adjustment)

Turn M.C. to adjust the clock.

Press M.C. to select the desired setting.

OFF (off)—LOW (low)—MID (mid)—HI (high)

Turn M.C. to select the desired setting.

Cut-off frequency: OFF—50HZ—63HZ—80HZ

—100HZ—125HZ—160HZ—200HZ

Slope level: –6— –12

Press M.C. to display the setting mode.

Turn M.C. to adjust the front/rear speaker bal-

ance.

12H/24H (time notation)

SUB.W (subwoofer on/off setting)

Press M.C. to select the desired setting.

12H (12-hour clock)—24H (24-hour clock)

BALANCE (balance adjustment)

AUTO PI (auto PI seek)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Operating this unit

System menu

Turning the display off or on

The unit can automatically search for a different

station with the same programming, even during

preset recall.

FM STEP (FM tuning step)

Press and hold SRC/OFF until the unit

Press and hold DISP/DISP OFF until the

Normally, the FM tuning step employed by seek

tuning is 50 kHz. When AF or TA is on, the tuning

step automatically changes to 100 kHz. It may be

preferable to set the tuning step to 50 kHz when

AF is on.

turns off.

display turns on or off.

Press M.C. to turn Auto PI seek on or off.

Press and hold M.C. until the main menu

AUX (auxiliary input)

If an unwanted display appears

Turn off the unwanted display using the proce-

dures listed below.

appears in the display.

Activate this setting when using an auxiliary de-

vice connected to this unit.

Press M.C. to turn AUX on or off.

The tuning step remains at 50 kHz during man-

ual tuning.

Turn M.C. to change the menu option

and press to select SYSTEM.

Press M.C. to select the FM tuning step.

50 (50 kHz)—100 (100 kHz)

Press M.C. to display the main menu.

Turn M.C. to select the system menu

MW STEP (MW tuning step)

Switching the dimmer setting

You can adjust the brightness of illumination.

function.

Turn M.C. to change the menu option

Once selected, the following system menu func-

tions can be adjusted.

The MW tuning step can be switched between

9 kHz and 10 kHz.

and press to select SYSTEM.

For details, refer to System menu on the pre-

vious page.

Press M.C. to select the MW tuning step.

9 (9 kHz)—10 (10 kHz)

Turn M.C. to display DEMO OFF and press

Press M.C. to display the main menu.

to select.

Turn M.C. to display ILLUMI and press to

SP-P/O MODE (rear output and preout setting)

Turn M.C. to switch to YES.

Press M.C. to select.

select.

Using an AUX source

The rear speaker leads output and the RCA output

of this unit can be used to connect a full-range

speaker or subwoofer. Select a suitable option for

your connection.

Insert the stereo mini plug into the AUX

Press M.C. to select the desired setting.

input jack.

OFF (off)—ON (on)

You can also change the dimmer setting by

Press M.C. to display the setting mode.

Turn M.C. to select the desired setting.

You can select any one of the options in the fol-

lowing list:

Press SRC/OFF to select AUX as the

pressing and holding /DIMMER.

source.

Note

Initial menu

REAR/SUB.W – Select when there is a full-

range speaker connected to the rear speak-

er leads output and there is a subwoofer

connected to the RCA output.

AUX cannot be selected unless the auxiliary set-

ting is turned on. For more details, refer to AUX

(auxiliary input) on this page.

Press and hold SRC/OFF until the unit

turns off.

Press and hold M.C. until the main menu

SUB.W/SUB.W – Select when there is a

subwoofer connected directly to the rear

speaker leads output without any auxiliary

amp and there is a subwoofer connected

to the RCA output.

Switching the display

appears in the display.

Selecting the desired text information

Turn M.C. to change the menu option

Press DISP/DISP OFF to cycle between the fol-

and press to select INITIAL.

lowing:

REAR/REAR – Select when there is a full-

range speaker connected to the rear speak-

er leads output and the RCA output.

If there is a full-range speaker connected to

the rear speaker leads output and the RCA

output is not used, you may select either

REAR/SUB.W or REAR/REAR.

Source name

Source name and clock

tion.

Turn M.C. to select the initial menu func-

Once selected, the following initial menu func-

tions can be adjusted.

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Installation

Use this unit with a 12-volt battery and nega-

tive grounding only. Failure to do so may re-

sult in a fire or malfunction.

To prevent a short-circuit, overheating or mal-

function, be sure to follow the directions

below.

Perform these connections when using a sub-

woofer without the optional amplifier.

This unit

Connections

WARNING

Use speakers over 50 W (output value) and

between 4 W to 8 W (impedance value). Do

not use 1 W to 3 W speakers for this unit.

The black cable is ground. When installing

this unit or power amp (sold separately),

make sure to connect the ground wire first.

Ensure that the ground wire is properly con-

nected to metal parts of the car’s body. The

ground wire of the power amp and the one of

this unit or any other device must be con-

nected to the car separately with different

screws. If the screw for the ground wire loos-

ens or falls out, it could result in fire, genera-

tion of smoke or malfunction.







—

Disconnect the negative terminal of the bat-



tery before installation.

—

Secure the wiring with cable clamps or adhe-

sive tape. Wrap adhesive tape around wiring

that comes into contact with metal parts to

protect the wiring.

1 Power cord input

2 Rear output or subwoofer output

3 Front output

4 Antenna input

5 Fuse (10 A)

6 Wired remote input

Hard-wired remote control adapter can be

connected (sold separately).









—

Place all cables away from moving parts,

such as the shift lever and seat rails.

Place all cables away from hot places, such

as near the heater outlet.

Do not connect the yellow cable to the battery

by passing it through the hole to the engine

compartment.





1 To power cord input

2 Left

3 Right

4 Front speaker

5 Rear speaker

6 White

7 White/black

8 Gray

9 Gray/black

a Green

b Green/black

c Violet

d Violet/black

e Black (chassis ground)

Connect to a clean, paint-free metal location.

f Yellow

Connect to the constant 12 V supply termi-

nal.

g Red

Connect to terminal controlled by ignition

switch (12 V DC).

h Blue/white

Connect to system control terminal of the

power amp or auto-antenna relay control ter-

minal (max. 300 mA 12 V DC).

i Subwoofer (4 W)

Power cord

Perform these connections when not connect-

ing a rear speaker lead to a subwoofer.

POWER AMP

Ground wire

—

Cover any disconnected cable connectors

with insulating tape.

—

Do not shorten any cables.

Never cut the insulation of the power cable of

this unit in order to share the power with

other devices. The current capacity of the

cable is limited.







Other devices

(Another electronic

device in the car)

Metal parts of car’s body



—

Use a fuse of the rating prescribed.

Never wire the negative speaker cable directly

to ground.









—

Never band together negative cables of multi-

ple speakers.

Important

When installing this unit in a vehicle without

an ACC (accessory) position on the ignition

switch, failure to connect the red cable to the

terminal that detects operation of the ignition

key may result in battery drain.

When this unit is on, control signals are sent

through the blue/white cable. Connect this

cable to the system remote control of an ex-

ternal power amp or the vehicle’s auto-anten-

na relay control terminal (max. 300 mA

12 V DC). If the vehicle is equipped with a

glass antenna, connect it to the antenna

booster power supply terminal.

Never connect the blue/white cable to the

power terminal of an external power amp.

Also, never connect it to the power terminal

of the auto antenna. Doing so may result in

battery drain or a malfunction.

ACC position

No ACC position

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Installation

Make sure that the unit is installed securely in

j When using a subwoofer of 70 W (2 W), be

sure to connect the subwoofer to the violet

and violet/black leads of this unit. Do not

connect anything to the green and green/

black leads.

Use commercially available parts when instal-

ling.

Installation

place. An unstable installation may cause skipping

or other malfunctions.

Important

Check all connections and systems before

final installation.

Do not use unauthorized parts as this may

cause malfunctions.

Consult your dealer if installation requires

drilling of holes or other modifications to the

vehicle.

DIN Front-mount

DIN Rear-mount

Insert the mounting sleeve into the dash-

k Not used.

l Subwoofer (4 W) × 2

Determine the appropriate position

board.

where the holes on the bracket and the side

of the unit match.

For installation in shallow spaces, use the sup-

plied mounting sleeve. If there is enough space,

use the mounting sleeve that came with the ve-

hicle.

Notes

With a 2 speaker system, do not connect any-

thing to the speaker leads that are not con-

nected to speakers.

Do not install this unit where:

—

it may interfere with operation of the vehicle.

it may cause injury to a passenger as a result

of a sudden stop.

Change the initial menu of this unit. Refer to

SP-P/O MODE (rear output and preout set-

ting) on page 8.

—

Secure the mounting sleeve by using a

screwdriver to bend the metal tabs (90°) into

place.

The semiconductor laser will be damaged if

it overheats. Install this unit away from hot

places such as near the heater outlet.

Optimum performance is obtained when the

unit is installed at an angle of less than 60°.

The subwoofer output of this unit is monau-

ral.

Tighten two screws on each side.

Power amp (sold separately)

Perform these connections when using the op-

tional amplifier.

60°

Truss screw (5 mm × 8 mm)

Mounting bracket

Dashboard or console

Dashboard

Mounting sleeve









When installing, to ensure proper heat dis-

persal when using this unit, make sure you

leave ample space behind the rear panel and

wrap any loose cables so they are not block-

ing the vents.

Install the unit as illustrated.

Removing the unit

Remove the trim ring.









1 System remote control

Connect to Blue/white cable.

2 Power amp (sold separately)

Leave ample

space

5 cm

3 Connect with RCA cables (sold separately)

4 To Front output

5 cm

5cm

5 Front speaker

Nut

6 To Rear output or subwoofer output

7 Rear speaker or subwoofer

Firewall or metal support

Metal strap

Screw

Trim ring

Notched tab

Releasing the front panel allows easier ac-

cess to the trim ring.

When reattaching the trim ring, point the

side with the notched tab down.

DIN front/rear mount

This unit can be properly installed using either

front-mount or rear-mount installation.

Screw (M4 × 8)

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Installation

Additional information

Troubleshooting

Insert the supplied extraction keys into

both sides of the unit until they click into

place.

Error messages

When you contact your dealer or your nearest

Pioneer Service Center, be sure to note the error

message.

Symptom

Cause

Action

Pull the unit out of the dashboard.

The display

You did not per- Perform operation

automatically form any opera- again.

returns to the tion within

Common

ordinary dis-

play.

about 30 sec-

onds.

Message

Cause

Action

AMP ERROR Unit fails to op- Check the speak-

The repeat

play range

changes un-

expectedly.

Depending on

the repeat play play range again.

range, the se-

lected range

may change

Select the repeat

erate or speaker er connection. If

connection is

incorrect; pro-

tective circuit is after the engine is

activated.

the message fails

to disappear even

Removing and re-attaching the

front panel

You can remove the front panel to protect your

unit from theft.

switched off/on,

contact your deal-

er or an author-

ized Pioneer

Service Station

for assistance.

when another

folder or track is

being selected

or during fast

forwarding/re-

versing.

Press the detach button and push the front

panel upward and pull it toward you.

For details, refer to Removing the front panel to

protect your unit from theft and Re-attaching the

front panel on page 4.

A subfolder is Subfolders can- Select another re-

CD player

Message

not played

back.

not be played

when FLD (fold-

er repeat) is se-

lected.

peat play range.

Cause

Action

ERROR-07,

The disc is dirty. Clean the disc.

11, 12, 17, 30

NO XXXX ap- There is no em- Switch the display

pears when a bedded text in- or play another

The disc is

scratched.

Replace the disc.

display is

formation.

track/file.

ERROR-07,

10, 11, 12,

15, 17, 30,

There is an elec- Turn the ignition

changed (NO

TITLE, for ex-

ample).

trical or me-

chanical error.

switch OFF and

back ON, or

switch to a differ-

ent source, then

back to the CD

player.

The unit is

You are using a Move electrical

malfunction- device, such as devices that may

ing.

There is inter- phone, that

ference.

a cellular

be causing the in-

terference away

ERROR-15

ERROR-23

The inserted

disc is blank.

Replace the disc.

transmits elec- from the unit.

tric waves near

the unit.

Unsupported

CD format.

Replace the disc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Additional information

Use only conventional, fully circular discs. Do not

use shaped discs.

Message

Cause

Action

Message

Cause

Action

Message

Cause

Action

FORMAT

READ

Sometimes

there is a delay message disap-

between the pears and you

Wait until the

SKIPPED

The connected Play an audio file

USB storage de- not embedded

vice contains

ERROR-19

Communication Perform one of

failed.

the following op-

erations.

with Windows

start of playback hear sound.

and when you

start to hear any

sound.

files embedded Media DRM 9/10.

–Turn the ignition

switch OFF and

back ON.

–Disconnect the

USB storage de-

vice.

–Change to a dif-

ferent source.

Then, return to

the USB source.

with Windows

Mediaä DRM 9/

10.

Do not insert anything other than a CD into the

CD loading slot.

Do not use cracked, chipped, warped, or other-

wise damaged discs as they may damage the play-

er.

NO AUDIO

SKIPPED

The inserted

disc does not

contain any

playable files.

Replace the disc.

PROTECT

All the files in

Transfer audio

the USB storage files not em-

device are em-

bedded with

Windows Media

Unfinalized CD-R/RW discs cannot be played

back.

Windows Media DRM 9/10 to the

The inserted

disc contains

DRM protected

files.

Replace the disc.

DRM 9/10.

USB storage de-

vice and connect.

Do not touch the recorded surface of the discs.

Store discs in their cases when not in use.

ERROR-23

STOP

USB storage de- USB storage de-

vice was not for- vice should be for-

matted with matted with

FAT12, FAT16 or FAT12, FAT16 or

N/A USB

The USB device ! Connect a USB

connected to is Mass Storage

Do not attach labels, write on or apply chemicals

to the surface of the discs.

PROTECT

All the files on

the inserted

disc are em-

bedded with

DRM.

not supported

by this unit.

Class compliant

device.

FAT32.

To clean a CD, wipe the disc with a soft cloth out-

ward from the center.

! Disconnect

your device and

replace it with a

compatible USB

storage device.

There are no

songs in the

current list.

Select a list that

contains songs.

Condensation may temporarily impair the player’s

performance. Let it rest for about one hour to ad-

just to a warmer temperature. Also, wipe any

damp discs off with a soft cloth.

USB storage device

Handling guidelines

Discs and player

CHECK USB

The USB con-

nector or USB

Check that the

USB connector or

Message

Cause

Action

Playback of discs may not be possible because of

disc characteristics, disc format, recorded applica-

tion, playback environment, storage conditions,

and so on.

FORMAT

READ

Sometimes

Wait until the

cable has short- USB cable is not

there is a delay message disap-

between the pears and you

start of playback hear sound.

and when you

start to hear any

sound.

circuited.

caught in some-

thing or dam-

aged.

Use only discs that feature either of the following

two logos.

Road shocks may interrupt disc playback.

The connected Disconnect the

USB storage de- USB storage de-

vice consumes vice and do not

more than maxi- use it. Turn the

mum allowable ignition switch to

Read the precautions for discs before using them.

NO AUDIO

There are no

songs.

Transfer the audio

files to the USB

storage device

and connect.

current.

OFF, then to ACC

or ON and then

connect only

Use 12-cm discs. Do not use 8-cm discs or an

adapter for 8-cm discs.

The connected Follow the USB

USB storage de- storage device in-

vice has secur- structions to dis-

compliant USB

storage devices.

ity enabled.

able the security.

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Additional information

Frequent loading and ejecting of a DualDisc may

result in scratches on the disc. Serious scratches

can lead to playback problems on this unit. In

some cases, a DualDisc may become stuck in the

disc loading slot and will not eject. To prevent this,

we recommend you refrain from using DualDisc

with this unit.

Please refer to the information from the disc man-

ufacturer for more detailed information about

DualDiscs.

WAV

USB storage device

When using discs that can be printed on label sur-

faces, check the instructions and the warnings of

the discs. Depending on the discs, inserting and

ejecting may not be possible. Using such discs

may result in damage to this equipment.

File extension: .wav

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers.)

Quantization bits: 8 and 16 (LPCM), 4 (MS

ADPCM)

Playable folders: up to 500

Playable files: up to 15 000

Do not attach commercially available labels or

other materials to the discs.

Sampling frequency: 16 kHz to 48 kHz (LPCM),

22.05 kHz and 44.1 kHz (MS ADPCM)

Playback of copyright-protected files: Not compati-

ble

The discs may warp making the disc unplay-

able.

The labels may come off during playback and

prevent ejection of the discs, which may result

in damage to the equipment.

Supplemental information

Partitioned USB storage device: Only the first par-

tition can be played.

Only the first 32 characters can be displayed as a

file name (including the file extension) or a folder

name.

Compressed audio

compatibility (disc, USB)

There may be a slight delay when starting play-

back of audio files on a USB storage device with

numerous folder hierarchies.

USB storage device

This unit may not operate correctly depending on

the application used to encode WMA files.

WMA

Address any questions you have about your USB

storage device to the manufacturer of the device.

File extension: .wma

There may be a slight delay at the start of playback

of audio files embedded with image data or audio

files stored on a USB storage device that has nu-

merous folder hierarchies.

CAUTION

Bit rate: 48 kbps to 320 kbps (CBR), 48 kbps to

384 kbps (VBR)

Pioneer cannot guarantee compatibility with

all USB mass storage devices and assumes

no responsibility for any loss of data on

media players, smart phones, or other devi-

ces while using this product.

Do not leave discs or a USB storage device

in any place that is subject to high tempera-

tures.

Connections via USB hub are not supported.

Do not connect anything other than a USB stor-

age device.

Sampling frequency: 32 kHz, 44.1 kHz, 48 kHz

Windows Media Audio Professional, Lossless,

Voice/DRM Stream/Stream with video: Not com-

patible

Firmly secure the USB storage device when driv-

ing. Do not let the USB storage device fall onto the

floor, where it may become jammed under the

brake or accelerator pedal.

Disc

Playable folder hierarchy: up to eight tiers (A prac-

tical hierarchy is less than two tiers.)

Depending on the USB storage device, the follow-

ing problems may occur.

MP3

Playable folders: up to 99

Sequence of audio files

The user cannot assign folder numbers and

specify playback sequences with this unit.

Operations may vary.

Playable files: up to 999

File extension: .mp3

The storage device may not be recognized.

Files may not be played back properly.

The device may generate noise in the radio.

File system: ISO 9660 Level 1 and 2, Romeo, Joliet

Multi-session playback: Compatible

Packet write data transfer: Not compatible

Bit rate: 8 kbps to 320 kbps (CBR), VBR

Sampling frequency: 8 kHz to 48 kHz (32 kHz,

44.1 kHz, 48 kHz for emphasis)

Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4

(ID3 tag Version 2.x is given priority over Version

1.x.)

DualDiscs

Regardless of the length of blank sections be-

tween the songs from the original recording, com-

pressed audio discs play with a short pause

between songs.

DualDiscs are two-sided discs that have a record-

able CD for audio on one side and a recordable

DVD for video on the other.

M3u playlist: Not compatible

Since the CD side of DualDiscs is not physically

compatible with the general CD standard, it may

not be possible to play the CD side with this unit.

MP3i (MP3 interactive), mp3 PRO: Not compatible

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Additional information

Specifications

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

Example of a hierarchy

MP3

Supply of this product only conveys a license for

private, non-commercial use and does not con-

vey a license nor imply any right to use this prod-

uct in any commercial (i.e. revenue-generating)

real time broadcasting (terrestrial, satellite,

cable and/or any other media), broadcasting/

streaming via internet, intranets and/or other

networks or in other electronic content distribu-

tion systems, such as pay-audio or audio-on-de-

mand applications. An independent license for

such use is required. For details, please visit

http://www.mp3licensing.com.

ꢀ

General

Rated power source ......... 14.4 V DC

(allowable voltage range:

12.0 V to 14.4 V DC)

USB

USB standard specification

ꢁ

: Folder

................................... USB 2.0 full speed

Maximum current supply

................................... 1 A

USB Class ....................... MSC (Mass Storage Class)

File system ....................... FAT12, FAT16, FAT32

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

audio)

Grounding system ............ Negative type

Maximum current consumption

................................... 10.0 A

Dimensions (W × H × D):

DIN

: Compressed

audio file

ꢂ

ꢃ

ꢄ

ꢅ

01 to 05: Folder

number

Chassis .............. 178 mm × 50 mm ×

165 mm

Level 1 Level 2 Level 3 Level 4

1 to 6: Playback

sequence

Nose .................. 188 mm × 58 mm ×

16 mm

(Windows Media Player)

WAV signal format ........... Linear PCM & MS ADPCM

(Non-compressed)

Disc

Chassis .............. 178 mm × 50 mm ×

165 mm

Nose .................. 170 mm × 46 mm ×

16 mm

Folder selection sequence or other operation

may differ depending on the encoding or writing

software.

FM tuner

WMA

Frequency range .............. 87.5 MHz to 108.0 MHz

Usable sensitivity ............. 9 dBf (0.8 µV/75 W, mono, S/N:

30 dB)

Windows Media is either a registered trademark

or trademark of Microsoft Corporation in the

United States and/or other countries.

This product includes technology owned by

Microsoft Corporation and cannot be used or

distributed without a license from Microsoft

Licensing, Inc.

Weight ............................. 1 kg

Signal-to-noise ratio ......... 72 dB (IEC-A network)

USB storage device

Audio

Maximum power output ... 50 W × 4

70 W × 1/2 W (for subwoofer)

Playback sequence is the same as recorded se-

quence in the USB storage device.

To specify the playback sequence, the following

method is recommended.

MW tuner

Continuous power output

................................... 22 W × 4 (50 Hz to 15 000 Hz,

5 % THD, 4 W load, both chan-

Frequency range .............. 531 kHz to 1 602 kHz (9 kHz)

530 kHz to 1 640 kHz (10 kHz)

Usable sensitivity ............. 25 µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62 dB (IEC-A network)

nels driven)

1 Create a file name that includes numbers

that specify the playback sequence (e.g.,

001xxx.mp3 and 099yyy.mp3).

2 Put those files into a folder.

3 Save the folder containing files on the USB

storage device.

However, depending on the system environment,

you may not be able to specify the playback se-

quence.

For USB portable audio players, the sequence is

different and depends on the player.

Load impedance .............. 4 W (4 W to 8 W allowable)

Preout maximum output level

................................... 2.0 V

Loudness contour ............ +10 dB (100 Hz), +6.5 dB

(10 kHz) (volume: –30 dB)

Equalizer (5-Band Graphic Equalizer):

Frequency ................. 80 Hz/250 Hz/800 Hz/

2.5 kHz/8 kHz

Equalization range .... 12 dB (2 dB step)

Subwoofer (mono):

SW tuner

Frequency range .............. 2 300 kHz to 7 735 kHz

(2 300 kHz to 2 495 kHz,

2 940 kHz to 4 215 kHz,

4 540 kHz to 5 175 kHz,

5 820 kHz to 6 455 kHz,

7 100 kHz to 7 735 kHz)

9 500 kHz to 21 975 kHz

(9 500 kHz to 10 135 kHz,

11 580 kHz to 12 215 kHz,

13 570 kHz to 13 870 kHz,

Frequency ................. 50 Hz/63 Hz/80 Hz/100 Hz/

125 Hz/160 Hz/200 Hz

Slope ........................ –6 dB/oct, –12 dB/oct

Gain ......................... +6 dB to –24 dB

Phase ....................... Normal/Reverse

15 100 kHz to 15 735 kHz,

17 500 kHz to 17 985 kHz,

18 015 kHz to 18 135 kHz,

21 340 kHz to 21 975 kHz)

Usable sensitivity ............. 28 µV (S/N: 20 dB)

Signal-to-noise ratio ......... 62 dB (IEC-A network)

CD player

System ............................ Compact disc audio system

Usable discs .................... Compact disc

Signal-to-noise ratio ......... 94 dB (1 kHz) (IEC-A network)

Number of channels ........ 2 (stereo)

MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3

WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch

audio)

iTunes

Apple and iTunes are trademarks of Apple Inc.,

registered in the U.S. and other countries.

Note

Specifications and the design are subject to

modifications without notice.

(Windows Media Player)

Download from Www.Somanuals.com. All Manuals Search And Download.

PIONEER CORPORATION

1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi,

Kanagawa 212-0031, JAPAN

PIONEER ELECTRONICS (USA) INC.

P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.

TEL: (800) 421-1404

PIONEER ELECTRONICS OF CANADA, INC.

340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, Canada

TEL: 1-877-283-5901

TEL: 905-479-4411

PIONEER EUROPE NV

Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique

TEL: (0) 3/570.05.11

PIONEER ELECTRONICS ASIACENTRE PTE. LTD.

253 Alexandra Road, #04-01, Singapore 159936

TEL: 65-6472-7555

PIONEER ELECTRONICS AUSTRALIA PTY. LTD.

5 Arco Lane, Heatherton, Victoria, 3202 Australia

TEL: (03) 9586-6300

PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.

Blvd.Manuel Avila Camacho 138 10 piso

Col.Lomas de Chapultepec, Mexico, D.F. 11000

TEL: 55-9178-4270

先鋒股份有限公司

台北市內湖區瑞光路407號8樓

電話： 886-(0)2-2657-3588

先鋒電子（香港）有限公司

香港九龍長沙灣道909號5樓

電話： 852-2848-6488

ã 2012 PIONEER CORPORATION.

Printed in Thailand

<QRB3250-A/N> ID

Download from Www.Somanuals.com. All Manuals Search And Download.

Philips Blu ray Player HTS3306 F7 User Manual
Philips CD Player AZ 7384 User Manual
Philips CRT Television 15PT1320 User Manual
Philips CRT Television TS2546C User Manual
Philips Projector LC4331 User Manual
Philips TV VCR Combo 14PV125 39 User Manual
Philips TV VCR Combo PV 225 User Manual
Pioneer Portable Speaker S IC651 LR User Manual
Poulan Lawn Mower 176085 User Manual
Powermate Portable Generator PM049650418 User Manual