Polaroid TV Receiver PTV 701 User Manual

Included
Location of controls  
7.0” LCD Display  
Portable Digital Television  
PTV-701  
1. LCD screen  
2. Dual speakers  
3. [Standby/Power] indicator  
4. [MENU] button  
1
5. [CH-] button  
6. [CH+] button  
2
DigitalTV  
Remote  
Control  
Antenna  
7. [AUTO/OK] button  
8. [VOL-] button  
3
4
5
6
7
8
9 10 11  
9. [VOL+] button  
10. [MODE] button  
11. Remote sensor  
12  
12. RF IN antenna jack  
13. VIDEO IN jack  
14. AUDIO IN L jack  
13  
14  
15  
15. AUDIO IN R jack  
17  
18  
16  
16. Headphone jack  
A / V  
Cables  
AC  
Adaptor  
DC  
Car Charger  
17. Power [ON/OFF] switch  
18. DC 9-12V IN jack  
19. TV stand (pull)  
User Guide  
20. Battery compartment  
Polaroid and Polaroid & Pixel are trademarks of PLR IP Holdings, LLC, used under license. PLR  
IP Holdings, LLC does not manufacture this product or provide any Manufacturer’s Warranty or  
support.  
19  
20  
2 - (AAA)  
Batteries  
User Guide  
Installing the batteries  
1. Open the battery cover.  
1. [MUTE] button  
Remote control  
2. [PICTURE] button  
3. [MENU] button  
4. [SLEEP] button  
5. [ ] left button  
6. Numeric buttons  
7. [ ] previous channel  
button  
8. [VOL-] volume down  
button  
9. [POWER] button  
10. [MTS] sound field  
button  
11. [ZOOM] display  
mode button  
12. [EXIT] button  
13. [EPG] program  
guide button  
14. [ ] up button  
15. [ ] right button  
16. [ENTER] button  
17. [ ] down button  
18. [TV/AV] source button  
2. Place the 2 (AAA) batteries (included) into the  
compartment. Be sure the positive and negative  
terminals are positioned correctly as shown.  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
1
2
3
4
5
6
7
8
3. Close the battery cover.  
Remote control  
Cover  
Batteries  
19. [INFO] program information button  
20. [CH+] channel up button  
21. [CH-] channel down button  
22. [ ---- ] channel program button  
23. [VOL+] volume up button  
Getting started  
Charging  
Connecting the antenna  
This television contains a built-in rechargeable battery. You may power the  
television by charging its internal battery or you may power the television by  
using the included AC adaptor. Follow the instructions below to charge the  
television properly.  
1. With the antenna in the down position, screw it into the RF IN antenna jack  
on the TV.  
2. For the best reception, stretch the antenna out to its fullest length before  
scanning for channels.  
1. Connect the AC adaptor to the DC 9-12V IN jack on the TV and plug it into a  
wall receptacle.  
2. Charging time depends on whether the TV is ON during charging or in  
standby mode.  
If the TV is ON – the charge time is approximately 6 hours.  
If the TV is in standby mode – the charge time is approximately 4 hours.  
3. When battery strength is low, the TV will display the following icon on the  
1
2
screen:  
,this means it is time to recharge the battery.  
4. The [Standby/Power] indicator light on the front of the TV turns green when:  
The power cord is connected, and the TV is fully charged.  
The TV is running on battery power.  
Note: The antenna must be connected to receive  
the highest amount of channels available during  
channel scanning.  
Note: Use the included car charger to charge the TV in a car  
or boat.  
Scanning for channels  
Scanning by remote control  
Select  
The first time the television is turned on you must scan for available channels.  
You should also scan for available channels whenever you are in a new area, or  
when reception is bad.  
1. Press the [MENU] button on  
the remote and press the [  
]
1. Make sure that the antenna is connected to the TV and slide the power  
button to select:  
[ON/OFF] switch to the ON position.  
2. When you turn on the TV for the  
first time, the following screen  
will be displayed:  
2. Press the [ ] button to select  
“Antenna”.  
3. Press the [ ] button to select  
“Air” or CATV(cable TV),  
depending on the type of  
connection.  
3. If this screen does not appear, then press the [AUTO/OK] button on the TV.  
4. Press the [ ] button to scroll to  
4. Press the [VOL+] button to select “Yes” and press [AUTO/OK] button  
“Auto Scan” and press the [  
button twice. The TV will start  
scanning for available channels  
and store them into memory.  
]
to confirm.  
5. The TV will start scanning  
for available channels and  
store them into memory.  
Note: Do not move or unplug the TV while scanning for  
channels/subchannels.  
This television is not meant to be used in a  
moving vehicle. ATSC Digital tuners are not  
capable of receiving a signal when in motion.  
Do not move or unplug the TV while scanning  
for channels/programs as this will interrupt the  
scanning process and you will not receive all  
possible channels/subchannels.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic operation  
Adjusting the volume  
Channel selection  
The volume can be adjusted from 0-100.  
Note: The TV’s receiver stores up to 69 channels, and each channel can  
store up to 8 subchannels.  
1. Press the [VOL+] button on the TV or the remote to raise the volume.  
2. Press the [VOL-] button on the TV or the remote to lower the volume.  
1. Press the [CH+] button to play the next channel/subchannel.  
2. Press the [CH-] button to play the previous channel/subchannel.  
3. To select a specific channel using the remote, use the numeric keypad.  
3. Press the [MUTE] button on the remote to mute the TV sound.  
Press the [MUTE] button again to restore sound.  
Choosing picture mode  
1. Press the [PICTURE] button on the remote to enter the picture mode options.  
Note: If a channel has more than one subchannel associated with it (for  
example channel 16.4), press the [1] button then press the [6] button then  
2. Keep pressing the [PICTURE] button to choose between the following  
press the [ ---- ] button then press the [4] button.  
picture modes: Standard, Dynamic, Soft or Personal.  
Choosing picture size  
3
4
Sleep timer  
1. Press the [ZOOM] button on the remote to enter the zoom mode options.  
1. Press the [SLEEP] button on the remote to enter the sleep timer  
2. Keep pressing the [ZOOM] button to choose between WIDE and NORMAL  
zoom modes.  
mode options.  
2. Keep pressing the [SLEEP] button to choose between the following sleep  
timer options:  
OFF / 15 / 30 / 60 / 90 / 120 / 180 / 240 minutes  
Normal  
Wide  
3. The TV will go into standby mode after the chosen time allotment.  
Choose “OFF” to disable the sleep timer and return to normal viewing.  
Changing the TV settings  
Information Guide  
You can change the settings on the TV by entering the different settings menus  
and using the following procedure to navigate them:  
You can access the information guide to display current, past and future  
programming information.  
1. Press the [MENU] button.  
1. Press the [INFO] button on the remote to bring up the current program  
information:  
2. Use the [ ] or [ ] button on the remote or the [VOL-] or [VOL+] button  
Current channel  
Program name  
on the TV to scroll left or right to select the preferred settings menu.  
Audio mode  
3. Press the [ ] or [ ] button on the remote or the [CH+] or [CH-]  
button on the TV to scroll up or down on the menus to select the desired  
settings.  
Resolution  
Channel type  
Signal strength  
Date & Time  
Program time  
4. Press the [ ] or [ ] button on the remote or the [VOL+] or [VOL-] button  
on the TV to scroll left or right to change to the desired settings.  
2. Press the [EPG] button on the remote to bring up the Electronic Program  
Guide to view information on past, current or future programming on the  
selected channel/program.  
5. Press the [MENU] button to confirm the new settings and return to the  
menu options.  
3. Use the [ ] or [ ] button to scroll through past or future program  
6. Press the [EXIT] button to close the settings menu.  
information.  
There are 5 different settings menus  
4. Use the [ ] or [ ] button to scroll through different channel information.  
Current  
channel  
Program  
name  
Picture  
settings  
Audio  
settings  
Time & date Options  
setting settings  
Channel  
settings  
Date  
& Time  
Program  
summary  
The TV will remember the settings until they are changed, even if the player is  
set to standby mode. To restore the settings to factory default, scroll right to  
the “Options Settings” menu, then scroll down to “Restore Default”, and  
scroll right to open the options menu and select “Yes” to confirm (you will have  
to scan for channels again after restoring default settings).  
Note: Program information and/or availability may vary by  
area depending on local service providers.  
External connections  
Troubleshooting  
Cable TV  
No picture and sound – Check that the AC adaptor is properly attached  
and plugged in, and check that the battery is charged. Make sure that the TV  
input is set to TV.  
1. Disconnect the external antenna from the unit and attach the  
coaxial cable antenna to the RF IN antenna jack.  
No picture – The TV reception signal might be weak. Try scanning for  
2. Press the [AUTO/OK] button on the TV to enter the channel  
scanning screen.  
channels again or move the TV to a different location and scan for channels.  
3. Press the [VOL+] button to select “Yes” and press the [AUTO/OK] button  
to confirm. The TV will start scanning for available cable channels and store  
them into memory.  
No sound – Check that the volume is turned up and the mute function is not  
on and that headphones are not plugged into the TV. Also, the signal might be  
weak, try moving the TV to a new location and scanning for channels again.  
4. To scan for channels with the remote, connect the cable antenna to the  
RF IN jack and refer to “Scanning by remote control”.  
External DVD or VCR  
Poor reception – Try adjusting the antenna or scanning for channels again.  
1. Using the supplied A/V Cable, plug the Yellow (Video), Red (Audio R),  
and White (Audio L) plugs into the corresponding ”OUT” jacks on the  
external source.  
5
Dark or blurred picture – Try adjusting the brightness and contrast in the  
2. Plug the other ends into the corresponding “AV IN” jacks on the side of the TV.  
picture settings menu, also check that the battery is charged enough.  
AV IN  
PTV-701  
Unclear or unstable picture - Try adjusting the antenna or scanning for  
channels again.  
A/V OUT DVD Player  
Snow in picture – Most likely a power interference issue such as radio  
frequency, power lines, etc. is interfering with the reception. Try adjusting the  
antenna or moving the TV to a different location and scanning for channels again.  
3. Press the [TV/AV] button on the  
remote or the [MODE] button on  
the TV to switch the input to “AV IN”.  
Safety precautions  
Legal information  
LimitedWarranty  
FCC Part 15:  
This Product is supplied and distributed new by AIT, Inc. (AIT”) to the original consumer  
This equipment has been tested and found to comply with the requirements for a Class B digital device  
under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended  
to provide reasonable protection against harmful interference in a residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful  
interference to radio or television reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or more of the following measures:  
purchaser and is warranted by AIT against defects in material and workmanship for a period  
of one year from your date of purchase (“Warranty”).  
In the unlikely event that this product is defective, or does not perform properly, you may within  
one year from your original date of purchase return it to the authorized service center for  
repair or exchange.  
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THE PLUG WITH AN EXTENSION CORD,  
RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT  
BLADE EXPOSURE.  
TO OBTAINWARRANTY SERVICE:  
- Provide proof of the date of purchase within the package (Dated bill of sale)  
- Prepay all shipping costs to the authorized service center, and remember  
to insure your return.  
Re-orient or relocate the receiving antenna.  
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN  
OR MOISTURE. TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT,  
FULLY INSERT.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver  
is connected.  
- Include a return shipping address (no P.O. Boxes), a telephone contact  
number, and the defective unit within the package.  
- Describe the defect or reason you are returning the product. Your product  
will be repaired or replaced, at our option, for the same or similar model of equal value if  
examination by the service center determines this product is defective. Products received  
damaged as a result of shipping, will require you to file a claim with the carrier.  
Consult the dealer or an experienced radio/TV technician for help.  
Do not attempt to repair or modify this equipment.  
Warning: Changes or modifications to this equipment not expressly approved by the party responsible for  
compliance could void the users authority to operate the equipment.  
CAUTION  
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
The shipping address of the authorized service center is:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that may cause  
undesired operation.”  
AIT, Inc.  
ATTN: Returns Department  
14-C 53rd Street  
Brooklyn, NY 11232  
RISK OF ELECTRIC SHOCK  
DO NOT OPEN  
The lightning ꢀash with arrowhead  
symbol, within an equilateral triangle,  
is intended to alert the user to the  
presence of uninsulateddangerous  
voltage”within the products enclosure  
that may be of suꢁcient magnitude  
to constitute a risk of electric shock  
to persons.  
The exclamation point within the  
equilateral triangle is intended to alert  
the user to the presence of important  
operating and maintenance (servicing)  
instructions in the literature  
accompanying the product.  
WARNING: TO REDUCE THE RISK OF  
IN NO EVENT WILL AIT, ITS MANUFACTURERS, DISTRIBUTORS OR PLR IP HOLDINGS, LLC  
BE LIABLE FOR ANY INCIDENTAL, DIRECT, INDIRECT, SPECIAL, PUNITIVE OR CONSEQUENTIAL  
DAMAGES (SUCH AS, BUT NOT LIMITEDTO, DAMAGES FOR LOSS OF PROFITS, BUSINESS,  
SAVINGS, DATA OR RECORDS) RELATEDTOTHIS PRODUCT. EXCEPT AS STATED HEREIN,  
NO OTHER WARRANTIES SHALL APPLY.  
,
DO NOT REMOVE  
ECLOEVCETRRI(COSRHBOACCKK).  
PLR IP Holdings, LLC, its licensees and affiliates, fully supports all electronic waste initiatives. As  
responsible stewards of the environment, and to avoid violating established laws, you should properly dispose  
of this product in compliance with all applicable regulations, directives or other governances in the area where  
you reside. Please check with local authorities or the retailer where you purchased this product to determine  
a location where you can appropriately dispose of the product.  
NO USER SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
Should you have any questions or problems concerning this product, please contact our  
customer service department at:  
Electronic Recycling to learn more about the specific laws in your area and to locate a collection facility  
near your home.  
Customer Support:  
1-877-768-8483 (Toll Free)  
If your electronic device has internal memory on which personal or other confidential data may be stored, you  
may want to perform a data sanitization process before you dispose of your device to assure another party  
cannot access your personal data. Data sanitization varies by the type of product and its software, and you  
may want to research the best sanitization process for your device before disposal.You may also check with your  
local recycling facility to determine their data sanitization procedures during the recycling process.  
Monday -Thursday: 9AM - 5PM (EST)  
Friday: 9AM - 3PM (EST)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Baby Accessories SCF643 71 User Manual
Philips Indoor Furnishings 41621 48 16 User Manual
Philips TV VCR Combo 14PV227 User Manual
Pioneer Car Stereo System DEH P5200 User Manual
Pioneer DVD Recorder DVR 545H S User Manual
Pioneer Speaker System S CR52 QL User Manual
Planar Car Video System PT2245PW User Manual
PNY Network Card P DSA150 PCI RF User Manual
Porter Cable Trimmer 6602 User Manual
Power Acoustik Car Video System PTID 3600 User Manual