Printronix Printer SLPA8000r MP2 User Manual

Printronix Guide Specification  
RFID Label  
915 MHz, 96 Bit, EPC Class 1, Gen 2  
Rafsec Short Dipole Antenna  
Applicable Printer Models  
Print and Apply Models  
SLPA8000r MP2  
Desktop Models  
SL4M MP2  
SLPA7000r MP2  
SL5000r MP2  
Disclaimer  
Notwithstanding anything to the contrary in this document, the guidelines, suggestions and other information  
included in this document or otherwise provided to the recipient, including the guidelines and suggestions for  
developing converted RFID labels, are provided by Printronix on an "as is" basis and without warranty of  
any kind whatsoever, expressed or implied. In particular, Printronix disclaims any implied warranty of  
merchantability or fitness for a particular purpose. Printronix will not be liable under any circumstances for  
any damages or losses related in any way to use of the guidelines, specifications or other information,  
including damages, which may be incurred as a result of labels not working properly in a specific  
application. All specifications subjective to change without notice. Testing of the converted labels in the  
printer is recommended prior to production quantities.  
2/12/07  
RFID Label Guide Specification  
Gen 2, Rafsec Short Dipole Antenna  
182316-000 Rev C  
Page 1 of 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.3.2. Adhesive interface to liner shall be uniform and exhibit the same release  
characteristics along the full length of the label.  
3.4. Perforations Between Labels  
3.4.1. For SL4M and SL5000 models – per user requirements except no perforations for  
Peel Mode.  
3.4.2. For SLPA8000 and SLPA7000 models – no perforation between labels.  
3.5. Roll Configurations  
3.5.1. SL4M and SL5000 models  
3.5.1.1. Inside core diameter: 3 inches (76.2 mm).  
3.5.1.2. Outside roll diameter: 8" (203.2 mm) maximum.  
3.5.1.3. Label wind direction – label side out with orientation per Figure 1.  
3.5.2. SLPA8000 and SLPA7000 models  
3.5.2.1. Inside core diameter: 3.000” (+0.032”, -0.0”) (76.190 mm (+0.813, -  
0.0)) core acceptable for label lengths less than 5" (127.0 mm) with  
inlay lengths less than 2" (50.8 mm). For label lengths greater than 5"  
(127.0 mm) core diameter shall be 6.0" (+0.032”, -0.0”) (152.4 mm  
(+0.813, -0.0).  
3.5.2.2. Outside roll diameter: up to 12" (304.8 mm) maximum.  
3.5.2.3. Label wind direction – label side out with orientation per Figure 1.  
3.5.3. General  
3.5.3.1. Roll to be wound with sufficient tension to prevent telescoping during  
transit and handling.  
3.5.3.2. Splices to use clear tape, should be angled and placed under the labels  
and not between.  
3.6. Inlay  
3.6.1. Inlay: Rafsec Gen 2 Short Dipole inlay (similar to Rafsec sales code 3000704).  
3.6.2. Base antenna material: Etched aluminum.  
3.6.3. Nominal operating frequency: 915 (+/-15) MHz.  
3.6.4. EPC Protocol: UHF Class 1, Gen 2.  
3.6.5. Memory: 96 Bit Read/Write.  
3.7. Label Construction  
3.7.1. Inlay location with respect to label facestock outlined in Figure 1.  
3.7.2. 4” Printer Models  
3.7.2.1. Nominal label facestock width with inlay is 4.0" (101.6 mm).  
Maximum width of label construction supported by printer is 4.5"  
(114.3 mm) edge to edge (4.1" (104.1 mm) is printable).  
3.7.3. 6” Printer Models  
RFID Label Guide Specification  
Gen 2, Rafsec Short Dipole Antenna  
182316-000 Rev C  
Page 3 of 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.7.3.1. Printable label facestock width with inlay is 6.6" (167.6 mm).  
Maximum width of label construction supported by printer is 6.8"  
(172.7 mm) edge to edge.  
3.7.4. Minimum supported inlay pitch is 2.0" (50.8 mm).  
3.7.5. Gap Sensing  
3.7.5.1. Nominal gap between labels for gap sensing is 0.125" (3.17 mm).  
Minimum gap supported is 0.10" (2.54 mm).  
3.7.5.2. 1.0" (25.4 mm) minimum x 0.125" (3.17 mm) timing marks on the liner  
under the gap.  
3.7.6. Release Characteristics  
3.7.6.1. Labels shall be able to dispense in a print and apply application.  
3.8. Packaging and Handling  
3.8.1. RFID labels are static sensitive devices and should be packaged and handled  
accordingly.  
3.8.2. Low humidity environments can increase electrostatic discharge (ESD) conditions.  
ESD safeguards are recommended  
3.8.3. Avoid storing labels in elevated temperature environment.  
4. Thermal Transfer Ribbons for Printronix RFID Printers  
4.1. Ribbons for 4” RFID Printer Models  
4.1.1. Wax resin ribbon for best durability. Wax Resin Blend Ribbon 8500, 4.33" x 2051'  
(110 mm x 625 m), package of 6 ribbons, Printronix part no. 203485-103.  
4.1.2. General purpose wax ribbon. Wide Spectrum Wax Ribbon 8300, 4.33" x 2051'  
(110 mm x 625 m), package of 6 ribbons, Printronix part No. 175391-103.  
4.2. Ribbons for 6” RFID Printer Models  
4.2.1. Wax resin ribbon for best durability. Wax Resin Blend Ribbon 8500, 6.73" x 2051'  
(171 mm x 625 m), package of 6 ribbons, Printronix part no. 203485-106.  
4.2.2. General purpose wax ribbon. Wide Spectrum Wax Ribbon 8300, 6.73" x 2051'  
(171 mm x 625 m), package of 6 ribbons, Printronix part No. 175391-106.  
5. Contact Information  
5.1. For comments or questions, please contact Andrew Moore at [email protected] or  
714-368-2477.  
RFID Label Guide Specification  
Gen 2, Rafsec Short Dipole Antenna  
182316-000 Rev C  
Page 4 of 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Label Perforation  
Centered in Gap  
(see Para 3.4)  
Direction of label  
travel out of  
printer  
Leading Edge of Label  
Inlay Outline  
1.00" (+/-0.125")  
Trailing edge of timing  
mark to leading edge  
of antenna  
Label  
Rafsec Short Dipole  
Antenna outline  
Chip facing down,  
center slot back  
Minimum  
Pitch 2.0"  
2.0625"  
(+/- 0.1250")  
Liner edge to  
center of chip  
Liner  
1.0" min x 0.125"  
timing mark on  
back side of liner  
Corner radius:  
0.125" typ.  
4.0" minimum  
Variable see para  
3.7.2 and 3.7.3  
Printronix RFID Label Requirements for  
Rafsec Short Dipole Inlay  
Viewed from Facestock Side  
PRINTRONIX  
All Dimensions in Inches  
Figure 1. Label Layout  
RFID Label Guide Specification  
Gen 2, Rafsec Short Dipole Antenna  
182316-000 Rev C  
Page 5 of 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Security Camera C1475M C User Manual
Philips Baby Monitor SC466 User Manual
Philips Electric Shaver RQ1051 User Manual
Philips Flat Panel Television 15HF5443 User Manual
Philips Stereo System FW V795 User Manual
Phoenix Gold Car Amplifier SD11005 User Manual
Pioneer Industrial DVD Player DV 470 User Manual
Polaroid Digital Camera t833 User Manual
ProForm Home Gym PFEL51052 User Manual
PYLE Audio Speaker PAH1280 User Manual