PLL2010MW
LED LCD Monitor
Download from Www.Somanuals.com. All Manuals Search And Download.
| TABLE OF CONTENTS
FOR YOUR SAFETY...............................................................................................................3
PRECAUTIONS ...............................................................................................................4
SPECIAL NOTES ON LCD MONITORS .....................................................................5
BEFORE YOU OPERATE THE MONITOR ........................................................................5
FEATURES .......................................................................................................................5
PACKAGE LIST................................................................................................................6
INSTALLATION INSTRUCTIONS ...............................................................................7
CONTROLS AND CONNECTORS ..............................................................................8
ADJUSTING THE VIEWING ANGLE ........................................................................9
OPERATING INSTRUCTIONS.......................................................................................... 10
GENERAL INSTRUCTIONS....................................................................................... 10
FRONT PANEL CONTROL ....................................................................................... 11
HOW TO ADJUST A SETTING................................................................................. 12
ADJUSTING THE PICTURE....................................................................................... 13
PLUG AND PLAY......................................................................................................... 15
TECHNICAL SUPPORT (FAQ) ........................................................................................ 16
TECHNICAL SUPPORT (FAQ).................................................................................. 17
ERROR MESSAGE & POSSIBLE SOLUTION ......................................................... 17
APPENDIX............................................................................................................................ 18
SPECIFICATIONS ........................................................................................................ 18
FACTORY PRESET TIMING TABLE ......................................................................... 19
CONNECTOR PIN ASSIGNMENT .......................................................................... 20
WALL MOUNTING (OPTIONAL)............................................................................. 21
PLANAR SUPPORT............................................................................................................ 22
2
Download from Www.Somanuals.com. All Manuals Search And Download.
| FOR YOUR SAFETY
Before operating the monitor, please read this manual thoroughly. This manual should be
retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
NOTICE:
1. The changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
2. Shielded interface cables and AC power cord, if any, must be used in order to comply with
the emission limits.
3. The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modification to this equipment. It is the responsibilities of the user to
correct such interference.
WARNING:
To prevent fire or shock hazard, do not expose the monitor to rain or moisture. Dangerously
high voltages are present inside the monitor. Do not open the cabinet. Refer servicing to
qualified personnel only.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
•
•
Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry
tub, swimming pool or in a wet basement.
Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can
injure a person and cause serious damage to the appliance. Use only a cart or stand
recommended by the manufacturer or sold with the monitor. If you mount the monitor
on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
•
Slots and openings in the back and bottom of the cabinet are provided for ventilation.
To ensure reliable operation of the monitor and to protect it from overheating, be sure
these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug,
or similar surface. Do not place the monitor near or over a radiator or heat register. Do not
place the monitor in a bookcase or cabinet unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated on the
label. If you are not sure of the type of power supplied to your home, consult your dealer
or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third
(grounding) pin. This plug will fit only into a grounded power outlet as a safety feature.
If your outlet does not accommodate the three-wire plug, have an electrician install the
correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety
purpose of the grounded plug.
•
•
•
•
•
•
Unplug the unit during a lightening storm or when it will not be used for long period of
time. This will protect the monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or
electric shock.
Never push any object into the slot on the monitor cabinet. It could short circuit parts
causing a fire or electric shock. Never spill liquids on the monitor.
Do not attempt to service the monitor by yourself; opening or removing covers can
expose you to dangerous voltages and other hazards. Please refer all servicing to qualified
service personnel.
•
•
To ensure satisfactory operation, use the monitor only with UL listed computers which
have appropriate configured receptacles marked between 100 - 240V AC, Min. 5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIAL NOTES ON LCD MONITORS
The following symptoms are normal with LCD monitor and do not indicate a problem.
NOTES
•
•
•
•
Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off
the Power Switch and then turn it on again to make sure the flicker disappears.
You may find slightly uneven brightness on the screen depending on the desktop pattern
you use.
The LCD screen has effective pixels of 99.99% or more. It may include blemishes of 0.01%
or less such as a missing pixel or a pixel lit all of the time.
Due to the nature of the LCD screen, an after image of the previous screen may remain
after switching the image, when the same image is displayed for hours. In this case, the
screen is recovered slowly by changing the image or turning off the Power Switch for
hours.
•
When the screen becomes black or flashing, or cannot illuminate any more, contact your
dealer or service center to replace parts. Don’t repair the screen by yourself!
| BEFORE YOU OPERATE THE MONITOR
FEATURES
•
•
•
•
•
•
•
19.5”(49.5 cm) Wide ScreenTFT Color LCD Monitor
16:9 Widescreen
Crisp, Clear Display for Windows
Recommened Resolutions: 1600*900@60Hz
LED backlit, energy efficient
Ergonomic Design
Space Saving, Compact Case Design
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PACKAGE LIST
The product package should include the following items:
User's Guide
Monitor
Audio Cable
Power Cable
VGA Cable
6
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
STAND BASE INSTALLATION
The monitor is supplied complete with a stand.If you prefer to wall mount the monitor,
please follow the instructions on page 21 to remove the stand. Be sure to include the stand
with the monitor if it is necessary to return the unit.
•
Put the monitor on a stable surface.The monitor may cause injury or
damage if it falls or is dropped.
CAUTION
•
•
Do not give a strong impact to the monitor.It may cause damage.
Unplug the monitor before removal or installation to avoid electric shock
or damage.
<Installation>
1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being
scratched. Lay the monitor flat on a table with front face down.
2. Install the Stand and Base into the monitor as shown ih figure.
3. Insert the clip into the stand-cover as shown in figure.
<Remove>
1. Put a piece of soft cloth on the table beforehand to prevent the monitor from being
scratched. Lay the monitor flat on a table with front face down.
2. Pull the clip.
3. Press and hold the hooks inside, and pull the stand and base.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS AND CONNECTORS
POWER CORD
Power Source:
1. Make sure that the power cord is the correct type required in your area.
2. This LCD monitor has an internal universal power supply that allows operation in either
100/120V AC or 220/240V AC voltage area (No user adjustment is required.)
3. Connect the AC-power cord into your LCD monitor’s power input socket, The AC-power
cord may be connected to either a wall power outlet or the power outlet socket on your
PC, depending on the type of power cord supplied with your LCD monitor.
SIGNAL CABLE
Connecting the Signal Cable :Plug one end of the signal cable to the LCD monitor and the
other end to a computer or a video source.
Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter
(not supplied).
1
2
3
4
Figure 2 Connecting Cables
1.
2.
3.
4.
Power Cable
Audio cable
DVI Cable
D-SUB cable
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE VIEWING ANGLE
•
For optimal viewing it is recommended to look at the full face of the monitor, then adjust
the monitor’s angle to your own preference.
•
•
Hold the stand so you do not topple the monitor when you change the monitor’s angle.
You are able to adjust the monitor’s angle from -4° to 18°.
4
Figure 3
NOTES
•
Do not touch the LCD screen when you change the angle. It may cause damage or break
the LCD screen.
•
Careful attention is required not to catch your fingers or hands when you change the
angle.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
| OPERATING INSTRUCTIONS
GENERAL INSTRUCTIONS
Press the power button to turn the monitor on or off. The other control buttons are located
at front panel of the monitor (See Figure 4). By changing these settings, the picture can be
adjusted to your personal preferences.
•
•
•
The power cord should be connected.
Connect the video cable from the monitor to the video card.
Press the power button to turn on the monitor. The power indicator will light up.
1
2
3
4
5
Figure 4 External Control Button
1.
Source/AutoAdjust/EXIT button
2.
3.
4.
5.
ECO (-)
Volume Hotkey(+)
Menu / Enter
Power button
10
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PANEL CONTROL
•
•
Power Button:
Press this button to switch ON/OFF monitor’s power.
Power Indicator:
Blue — Power On mode.
Orange —Off mode.
•
•
MENU / ENTER :
Activates OSD menu or function adjust confirm.
ECO/(-)
Activates the ECO control when the OSD is OFF or navigate through adjustment icons
when OSD is ON or adjust a function when function is activated.
•
•
Volume /+ :
Activates the volume control when the OSD is OFF or navigate through adjustment icons
when OSD is ON or adjust a function when function is activated.
Source / Auto Adjust / Exit
When the OSD is OFF, pressing Auto/Source button will toggle between sources. Press
continuously to select the input source indicated in the message bar. Press Menu/Enter
button to change to the selected source. Auto configure hot key: (VGA input only) When
the OSD is OFF, press and hold down the button for 2 seconds to auto configure. When
OSD menu is ON, this button will act as a Exit Key (Exit OSD menu)
OSD Lock Function: Lock-All 4 buttons are locked except "POWER" button.
To lock the OSD, press and hold the MENU button while the monitor is off and then Press
power button to turn the monitor on. To un-lock the OSD, press and hold the MENU
button while the monitor is off and then press power button to turn the monitor on.
NOTES
•
•
•
•
Do not install the monitor in a location near heat sources such as radiators or air ducts, or
in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock.
Save the original shipping carton and packing materials, as they will come in handy if you
ever have to ship your monitor.
For maximum protection, repackage your monitor as it was originally packed at the
factory.
To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains
may be removed with a cloth lightly dampened with a mild detergent solution. Never use
strong solvents such as thinner, benzene, or abrasive cleaners, since these will damage
the cabinet. As a safety precaution, always unplug the monitor before cleaning it.
Do not scratch the screen with hard things, it may cause permanent damage.
Don’t leak liquid into monitor which will result in the damage of component.
•
•
11
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ADJUST A SETTING
1. Press the MENU-button to activate the OSD window.
2. Press + or - to navigate through the functions. Once the desired function is highlighted,
press the MENU-button to activate it. If the function selected has a sub-menu, press
+ or - again to navigate through the sub-menu functions. Once the desired function is
highlighted, press MENU-button to activate it.
3. Press + or - to change the settings of the selected function.
4. If you want to adjust any other function, repeat steps 2-3.
Figure 5 The OSD Message
12
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE PICTURE
Main Menu
Item
Luminance
Main Menu 1st Sub
Icon Menu Item
Contrast
Description
Adjusts Image brightness in relation to the
background.
Brightness Adjusts backlight levels.
Eco Mode
Picture Adjustment,
Standard:
Brightness = 90,
Contrast = 50.
Brightness, Contrast (Adjustable)
Text:
Brightness = 20,
Contrast = 50.
Brightness, Contrast ,Grayed. (Nonadjustable)
Internet:
Brightness = 40,
Contrast = 50.
Brightne ss, Contrast ,Grayed. (Nonadjustable)
Game:
Brightness = 60
Contrast = 50,
Brightness, Contrast ,Grayed. (Nonadjustable)
Movie:
Brightness = 80,
Contrast = 50,
Brightness, Contrast ,Grayed. (Nonadjustable)
Sports:
Brightness = 100,
Contrast = 50,
Brightness, Contrast ,Grayed. (Nonadjustable)
DCR
Dynamic contrast ratio.
Image
Setup
Clock
Phase
Adjust picture Clock to reduce Vertical-Line noise.
Adjust Picture Phase to reduce Horizontal-Line noise.
H. Position Adjust the horizontal position of the picture.
V. Position Adjust the vertical position of the picture.
Image Ratio Select Image Aspect Ratio.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Menu
Item
Main Menu 1st Sub
Icon Menu Item
Description
Color
Temp.
Normal
Warm
Cool
Normal Color Temperature.
(RGB value is nonadjustable)
Warm Color Temperature.
(RGB value is nonadjustable)
Cool Color Temperature.
(RGB value is nonadjustable)
RGB Color Temperature.
(RGB value is nonadjustable)
Adjust R.G.B levels as desired.
User-R:Adjust Red Gain
sRGB
User
User-G:Adjust Green Gain
User-B:Adjust Blue Gain
Color
Boost
Full Enhance Full Enhance.
Nature Skin Red level is raised.
Green Field Green level is raised.
Sky-blue
Auto Detect Auto gain for input signal.
Demo Demonstrates Color Boost Enhancements in the left
half of screen.
Frame Size Adjust the Size of the Frame.
Blue level is raised.
Picture
Boost
Contrast
Contrast Adjustment for Enhance Area.
Brightness Brightness Adjustment for Enhance Area.
H. Position Adjust the horizontal position of the Bright Frame.
V. Position Adjust the vertical position of the Bright Frame.
Bright Frame Enhance Area function.
OSD
Setup
H. Position Adjust the horizontal position of the OSD.
V. Position Adjust the vertical position of the OSD.
Timeout
Adjust the OSD timeout.
Language
Set OSD display language .( English is default setting )
Extra
Input Select Select input source.
DDC/CI
Reset
Select DDC/CI on or off.
Set Monitor to default status.
Information Show the resolution, H/V frequency of current input
timing.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PLUG AND PLAY
Plug & Play DDC2B Feature
This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC
STANDARD. It allows the monitor to inform the host system of its identity and, depending on
the level of DDC used, communicate additional information about its display capabilities.
The DDC2B is a bidirectional data channel based on the I²C protocol. The host can request
EDID information over the DDC2B channel.
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE IS NO VIDEO
INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATE PROPERLY, THERE
MUST BE A VIDEO INPUT SIGNAL.
This monitor meets the Green monitor standards as set by the Video Electronics Standards
Association (VESA) and The Swedish Confederation Employees (NUTEK). This feature is
designed to conserve electrical energy by reducing power consumption when there is
no video-input signal present. When there is no video input signal this monitor, following
a time-out period, will automatically switch to an OFF mode. This reduces the monitor's
internal power supply consumption. After the video input signal is restored, full power is
restored and the display is automatically redrawn. The appearance is similar to a "Screen
Saver" feature except the display is completely off. The display is restored by pressing a key
on the keyboard, or clicking the mouse.
USING THE RIGHT POWER CORD :
The accessory power cord for the Northern American region is the wallet plug with NEMA
5-15 style and is UL listed and CSA labeled. The voltage rating for the power cord shall be 125
volts AC.
Supplied with units intended for connection to power outlet of personal computer: Please
use a cord set consisting of a minimum No. 18 AWG, type SJT or SVT three conductors flexible
cord. One end terminates with a grounding type attachment plug, rated 10A, 250V, CEE-22
male configuration. The other end terminates with a molded-on type connector body, rated
10A, 250V, having standard CEE-22 female configuration.
Please note that power supply cord needs to use VDE 0602, 0625, 0821 approval power cord
in European counties.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
| TECHNICAL SUPPORT (FAQ)
Problem & Question
Possible Solution
Power LED is not on
*
Check if the Power Switch is in the ON position.
*
*
Power Cord should be connected.
Check if the PC system is Plug & Play
compatible.
No Plug & Play
*
Check if the Video Card is Plug & Play
compatible .
*
*
Check if the D-15 plug pin of Video Cable is
bent.
Adjust the Contrast and Brightness Controls.
Picture is fuzzy
Picture bounces or a wave pattern is * Move electrical devices that may cause
present in the picture
The power LED is ON (orange) but * Computer Power Switch should be in the ON
electrical interference.
there’s no video or no picture.
position.
*
*
*
*
Computer Video Card should be snugly seated
in its slot.
Make sure monitor’s video cable is properly
connected to the computer.
Inspect monitor’s video cable and make sure
none of the pins are bent.
Make sure computer is operational by hitting
the CAPS LOCK key on the keyboard while
observing the CAPS LOCK LED.The LED should
either turn ON or OFF after hitting the CAPS
LOCK key.
Missing one of the primary colors
(RED, GREEN, or BLUE)
*
Inspect the monitor’s video cable and make
sure that none of the pins are bent.
Screen image is not centered or sized * Adjust pixel frequency (CLOCK) and FOCUS or
properly.
press hot-key (AUTO).
Picture has color defects
(white does not look white)
Poor brightness or contrast
*
*
Adjust RGB color or select color temperature.
When the brightness of the screen lowers
after being used for a certain period and the
function of the display is affected, send it to our
authorized service center for repair.
Horizontal or vertical disturbances on * Use win 95/98/2000/ME/XP/Win 7 shut-down
the screen
mode Adjust CLOCK and FOCUS or perform
hot- key (AUTO-key).
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SUPPORT (FAQ)
CLOCK (pixel frequency) controls the number of pixels scanned by one horizontal sweep. If
the frequency is not correct, the screen shows vertical stripes and the picture has not correct
width.
FOCUS adjusts the phase of the pixel clock signal. With a wrong phase adjustment the
picture has horizontal disturbances in light picture.
For FOCUS and CLOCK adjustment use “dot-pattern” or win 95/98/2000/ME/XP/Win 7 shut-
down mode pattern.
ERROR MESSAGE & POSSIBLE SOLUTION
NO SIGNAL:
1. Check that the signal-cable is properly connected, if the connector is loose,tighten the
connector's screws.
2. Check the signal-cable's connection pins for damage.
INPUT NOT SUPPORT:
Your computer has been set to unsuitable display mode, set the computer todisplay mode
given in the following table.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
| APPENDIX
SPECIFICATIONS
LCD Panel
Driving system TFT Color LCD
Size
Pixel pitch
Video
49.5cm(19.5")
0.27(H ) × 0.27(V )
R,G,B Analog Interface
DVI-D
Input
Separate Sync. H/V TTL
H-Frequency
V-Frequency
Analog&Digital:30kHz – 83kHz
Analog&Digital:55-75Hz
16.7M Colors
Display Colors
Dot Clock
140MHz
Max. Resolution
Plug & Play
1600X900@60Hz
VESA DDC2BTM
Power Consumption ON Mode
OFF Mode
≤15W(TYP)
≤0.5W
Input Connector
Input Video Signal
Power Source
Environmental
Considerations
D-Sub mini 15 pin; DVI-D
Analog:0.7Vp-p(Standard),75Ω,Positive
100~240VAC,50/60Hz
Operating Temp: 0°C to 40°C
Storage Temp.: -25°C to 55°C
Operating Humidity: 10% to 85%
478.2(W)X360.2(H)X204.7(D)
3.0kg
Dimension
Weight (N. W.)
Power Consumption( Maximum )
Regulatory Compliance
25Watts
cTUVus, CE , FCC B
18
Download from Www.Somanuals.com. All Manuals Search And Download.
FACTORY PRESET TIMING TABLE
STAND
RESOLUTION
HORIZONTAL
FREQUENCY(kHZ)
VERTICAL
FREQUENCY(Hz)
VGA
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1280 x 720
1600 x 900
31.469
37.861
37.5
59.94
72.809
75
56.25
60.317
72.188
75
60.004
70.069
75.029
60
SVGA
XGA
35.156
37.879
48.077
46.875
48.363
56.476
60.023
45
WXGA
HD+
60
60
IBM MODE DOS 720 x 400
MAC MODE VGA 640 x 480
MAC MODE VGA 832 x624
31.469
35
49.725
70.087
66.667
74.551
19
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTOR PIN ASSIGNMENT
1
6
5
10
11
15
15 - Pin Color Display Signal Cable
PIN NO.
DESCRIPTION
Red
Green
Blue
Ground
Ground
R-Ground
G-Ground
B-Ground
PIN NO.
9.
10.
11.
12.
13.
14.
15.
DESCRIPTION
+5V
Detect Cable
Ground
DDC-Serial Data
H-Sync
1.
2.
3.
4.
5.
6.
7.
8.
V-Sync
DDC-Serial Clock
24-pin color display signal cable*
PIN No.
Description
TMDS data 2-
PIN No.
Description
1
2
13
14
15
16
17
18
19
20
21
22
23
24
NC
TMDS data 2+
TMDS data 2/4 shield
NC
+5 V power
3
GND (return for +5 V hsync.vsync)
Hot-plug detection
TMDS data 0-
4
5
NC
6
DDC clock
DDC data
NC
TMDS data 0+
7
TMDS data 0/5 shield
NC
8
9
TMDS data 1-
TMDS data 1+
TMDS data 1/3 shield
NC
NC
10
11
12
TMDS clock shield
TMDS clock+
DDC TMDS clock-
* only for certain models
20
Download from Www.Somanuals.com. All Manuals Search And Download.
WALL MOUNTING (OPTIONAL)
Refer to the instructions that come with the base mounting kit. To convert your LCD display
from a desk-mounted to a wall-mounted display, do the following:
1. Verify that the Power button is turned Off, then disconnect the power cord.
2. Lay the LCD display face down on a towel or blanket.
3. Remove the Plastic Covers from the back of the LCD display.
4. Remove the four screws attaching the base (Screw dimension: M4 x 14mm).
5. Remove the Rubber Plugs from inside the four VESA screw holes.
6. Attach the mounting bracket from the VESA compatible wall mounting kit (100 mm x 100
mm distance).
7. Attach the LCD display to the wall, following the instructions in the wall-mounting kit.
NOTE: For use only with Wall Mount Bracket with minimum weight/load: 12kg.
100.0mm
21
Download from Www.Somanuals.com. All Manuals Search And Download.
| PLANAR SUPPORT
Cables and Accessories
To find cables and accessories for your Planar monitor, touch screen or other Planar products
Technical Support
warranty information and access to Planar's Technical Library for online troubleshooting.
To speak with Planar Customer Support please have you model and serial number available
and dial:
Planar Support
Tel: 1-866-PLANAR1 (866-752-6271) or +1 503-748-5799 outside the US.
Hours: 24 hours a day, 7 days a week.
Toll or long distance charges may apply.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|