IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual
for the life of the equipment:
Model #: __________________________
Serial #: __________________________
Date Purchased: ___________________
Service & Parts Manual
Covering the
TM
SPINFRESH Option for
Solstice Fryers
L22-375 Rev 1 6/13
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
WARNING
The oil/shortening level should NOT fall below the
minimum indicated level line at any time. The use
of old shortening can be dangerous as it will have
a reduced flash point and be more prone to surge
boiling.
DO NOT use an open flame to check for gas leaks!
WARNING
If gas flow to appliance is interrupted, or pilots
extinguish, wait 5 minutes before attempting to
relight the pilot to allow any residual gas in
appliance to dissipate. Do not attempt to use this
appliance during a power outage.
WARNING
The contents of the crumb catch and/or filter pan
of any filter system must be emptied into a
fireproof container at the end of the frying
operation each day. Some food particles can
spontaneously combust into flames if left soaking
in certain oil/shortening materials.
WARNING
Ensure that the appliance can get enough air to
keep the flame burning correctly. If the flame is
starved for air, it can give off a dangerous carbon
monoxide gas. Carbon monoxide is a clear
odorless gas that can cause suffocation.
WARNING
Completely shut the appliance down when
shortening/oil is being drained from the appliance.
This will prevent the appliance from heating up
during the draining and filling process. Serious
injury can occur.
WARNING
Never add oil to the appliance when it is at
operating temperature. Splashing hot oil can
cause severe injuries.
WARNING
WARNING
This appliance is intended for indoor use only.
DO NOT supply the appliance with a gas that is not
indicated on the data plate. If you need to convert
the appliance to another type of fuel, contact your
dealer.
WARNING
DO NOT operate appliance unless all panels and
access covers are attached correctly.
WARNING
WARNING
Never add water to hot oil. Violent boiling can
occur causing severe injury.
It is recommended that this appliance be inspected
by a qualified service technician for proper
performance and operation on a yearly basis.
WARNING
Excessive loading or loading of over wet food can
cause surge boiling. The maximum cooking load
must not exceed (14T-1.5lbs(0.68kg), 14-3 lbs (1.36
kg), 18-5 lbs (2.27 kg)).
WARNING
There is an open flame inside this appliance. The
unit may get hot enough to set nearby materials on
fire. Keep the area around the appliance free from
combustibles.
WARNING
A country approved all pole circuit breaker with a
minimum open contact gap of 3mm must be used
for proper installation. (CE countries)
WARNING
DO NOT supply the appliance with a gas that is not
indicated on the data plate. If you need to convert
the appliance to another type of fuel, contact your
dealer.
L22-375 Rev 1 6/13
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1 Fire Safety Systems ------------------------------------------------------------------------------------------------------------------------- 5
2 Operation--------------------------------------------------------------------------------------------------------------------------------------- 5
3 Troubleshooting------------------------------------------------------------------------------------------------------------------------------- 5
4 Basket Engagement ------------------------------------------------------------------------------------------------------------------------- 6
5 Field Upgrade --------------------------------------------------------------------------------------------------------------------------------- 8
6 Basket Lift Relay Logic---------------------------------------------------------------------------------------------------------------------- 9
7 SPINFRESH Diagnostic Mode------------------------------------------------------------------------------------------------------------ 9
8 Exploded parts -------------------------------------------------------------------------------------------------------------------------------- 9
8.1 Superseded basket Lift Assembly built before September 2012 ------------------------------------------------------------ 10
8.2 Basket Lift Assembly built after September 2012 ------------------------------------------------------------------------------- 12
8.3 Superseded Enclosure Assembly built before September 2012 ------------------------------------------------------------ 14
8.4 Enclosure Assembly built after September 2012-------------------------------------------------------------------------------- 16
8.5 Superseded Cover & Damper Assembly built before September 2012---------------------------------------------------- 18
8.6 Cover Assembly built after September 2012 ------------------------------------------------------------------------------------- 19
8.7 Miscellaneous Parts -------------------------------------------------------------------------------------------------------------------- 20
8.8 Basket Assembly------------------------------------------------------------------------------------------------------------------------ 21
8.9 Bottom Assembly------------------------------------------------------------------------------------------------------------------------ 22
8.10
Splash Back Assembly---------------------------------------------------------------------------------------------------------- 23
9 Basket Lift Wiring Diagram--------------------------------------------------------------------------------------------------------------- 24
10
Schematic------------------------------------------------------------------------------------------------------------------------------ 25
L22-375 Rev 1 6/13
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Fire Safety Systems
If your appliance is equipped with SPINFRESHTM, the tank enclosure can interfere with the performance of pre-
existing fire safety systems. Modifications to the fire safety system should be performed by a professional who
is qualified in installing, designing and maintaining your fire safety system prior to operating any SPINFRESHTM
appliance.
WARNING
Replacing or adding appliances under a pre-existing fire safety system may require
modifications to the system. ALWAYS contact a professional who is qualified in installing,
designing and maintaining your fire safety system to assure that any appliances located
under the fire safety system are adequately protected.
2 Operation
If the appliance is equipped with SPINFRESHTM, place the basket directly onto the basket lift pin and close the
lid prior to starting the timer(s). The basket(s) will be lowered into the cook tank when the timer cycle starts. At
the end of the preset cooking time, the basket lift will raise the basket out of the cook tank and spin the basket to
remove excess oil. The lid may be opened during the cooking cycle but must be closed prior to the spin cycle.
WARNING
NEVER open the lid or reach into the SPINFRESHTM enclosure during the spin cycle. Serious
injury could result.
3 Troubleshooting
Issue
Possible Causes
Basket lift Circuit breaker is tripped
Loose power connection to basket lift
Basket lift transformer
Basket does NOT travel up or down
Basket lift driver board
Damaged/improperly wired relay
Basket lift actuator
Basket lift Circuit breaker is tripped
Loose power connection to basket lift
Lid magnet switch
Power supply
Stepper motor driver board
Stepper motor
Product is not placed evenly in the basket.
Bottom plate (holds basket straight in appliance)
Improper basket engagement
Basket does NOT spin
Basket spins erratically
L22-375 Rev 1 6/13, Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Basket Engagement
This procedure is to check the basket engagement during the spin cycle and make any adjustments if required.
WARNING
Oil/shortening must completely cover the heat tubes or
heating elements at all times while appliance is on.
Press
Press
Press
to turn the appliance ON.
to enter spin diagnostic mode.
to raise the basket to the highest position.
Check the basket drive pin’s location within the drive coupling. Adjust basket drive pin position as
described if required.
Check to assure that the top plate springs are not extending while the basket drive pin is in the coupling.
Adjust basket drive pin position as described if required.
L22-375 Rev 1 6/13, Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTICE
Do NOT rotate the proximity switch during this procedure. The rotation
of the switch is critical to accurately sensing the basket lift position.
If the basket drive pin position needs adjustment.
While holding the upper proximity switch in place, use a small screwdriver to loosen screw on the
switch. Move the switch up and down to adjust the upper position. Move the proximity switch the same
distance that the basket pin is away from its ideal location. After repositioning the switch, use a small
screwdriver to tighten the screw on the proximity switch to secure it in place.
Press
to move the basket to the middle position.
After the basket has moved to the middle position, press
upper position.
to move the basket to the newly defined
Repeat the previous steps until the basket drive pin is positioned correctly within the drive coupling.
L22-375 Rev 1 6/13, Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Field Upgrade
In February of 2013, various improvements to the SPINFRESHTM option were made available as a field upgrade
kit. Refer to the diagram below to identify if the appliance has been upgraded or not. If the appliance can be
upgraded, contact the factory to order the appropriate upgrade kit.
Upgrade kit part numbers:
Kit No.
Models Covered
Item 1
Item 2
Item 3
B8705901‐CL SG14R, SSH55
B8705902‐CL SG14
B8705903‐CL SE14
B5609901‐C
B5609902‐C
B5609903‐C
B5609904‐C
B5608802 B4516001‐C
B8705904‐CL SGH50, SEH50
L22-375 Rev 1 6/13, Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Basket Lift Relay Logic
Relay Controlled by
Switches
K1
K2
K3
K4
Spin (Upper) Position Proximity Switch Signal to the I‐12 computer
Cook (Lower) Position Proximity Switch Signal to the I‐12 computer
Signal to Basket lift driver board
Signal to Basket lift driver board
K4 Relay
Signal from the I‐12 Computer
Electrically Brakes the actuator movement
Start signal to the basket lift driver board K3 Relay
7 SPINFRESH Diagnostic Mode
Spin Diagnostics
Press
Step 1. Enter Factory Programming P‐1‐9‐9‐3
Step 2. Enter Spin Diagnostics
9
Spin Diagnostics
Button
Turns motor on & off
L
1
2
3
4
5
6
7
8
9
0
R
Increases motor speed
Decreases motor speed
Changes motor direction
Vibrate (not used)
Indicator light: door open/closed
Indicator light: cook position
Indicator light: load position
Indicator light: spin position
Move to cook position
Move to load position
Move to spin position
8 Exploded parts
L22-375 Rev 1 6/13, Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
8.1 Superseded basket Lift Assembly built before September 2012
See next page for parts list.
L22-375 Rev 1 6/13, Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Superseded Basket Lift Assembly built before September 2012
ITEM#
PART NO. DESC.
1
2
3
A5625802 BSKT LFT,BOX SPINFRESH
A5625901 BSKT LFT,MAG SW SPRT CLIP S
A5626002 BSKT LFT,BOX COV ACTR MOD S
PP10429‐M XFMR,80VA 120/208/240V TO 2
4
5
PP11068
RELAY,24VDC DPDT MTG TAB
6
7
8
9
60134001 CNTRL,BASKT LIFT DRIVER BOA
60134305 ACTR,25 3.3‐9.4 24VDC 1IPS SPIN
60174101 SPLY,SWITCHING PWR 2.6A 48V
60174001 DRVR,STEPPER MOTOR 3.5A 50V
A5626202 BSKT LFT,ACTR C‐CHAN BRKT S
60136901 CLAMP, BASKET LIFT LIMIT SWITCH
A5626302 B/L,TOP SPRT DRIP GRD
10
11
12
13
14
15
16
17
18
19
20
21
25
26
27
PP10686
PP10266
SCR, 6‐32 X 1/4 RDH PHILLIPS ZN
SCR, 4‐40 X 1/4 RDH ZN
60177502 STAND‐0FF, #6 X 1/2 NYLON
PP10674
PP10689
PP10023
SCR, 6‐32 X 5/8 RDH PHILLIPS ZN
SCR, 6‐32 X 1/2 RDH PHILLIPS ZN
SCR, 10‐24 X 3/8 SLF TAP
P0113300 SCR, 1/4‐20 X 1/2 HHC SST
PP10693 SCR, 10‐24 X 3/8 TH PHILLIPS ZN
P0093300 NUT, HEX (KEP) 1/4‐20 ZN
P6071140 CONN LIQUID TIGHT 3/8
A5626102 B/L,SD MTG BRKT LH
A5626104 B/L,SD MTG BRKT RH
L22-375 Rev 1 6/13, Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
8.2 Basket Lift Assembly built after September 2012
See next page for parts list.
L22-375 Rev 1 6/13, Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Basket Lift Assembly built after September 2012
B56092xx, Complete assembly
ITEM NO.
1
PART NO.
A5625802 BASKET LIFT, BOX
DESCRIPTION
QTY
1
2
700324-10 LABEL, SCHEMATIC WIRING SG,SE SPINFRESH
A5626002 BASKET LIFT, BOX COVER ACTUATOR MODULAR SG
PP10429-M TRANSFORMER, 80VA 120-208-240V TO 24V MCI
PP11068 RELAY, 24VDC DPDT WITH MOUNTING TABS
60134001 CNTRL,BASKT LIFT DRIVER BOARD
60134305 ACTUATOR, 25 3.3-9.4 245VDC 1IPS SPIN
60179101 POWER SUPPLY, 48 VDC 4.2A SPIN
60174001 DRIVER, STEPPER MOTOR 3.5A 50V
A5626202 BASKET LIFT, ACTUATOR C-CHANNEL BRKT
60133901 CORD, 16-3 AWG, IEC320M PLUG 28.0"
A5626302 BASKET LIFT, TOP SPRT DRIP GUARD BRACKET
PP10687 SCREW, 6-32 X 313 THRUSS HEAD PHILLIPS ZN
PP11351 SCREW, 4-40 X .750 ROUND HEAD SLOTTED ZN
60177503 STAND-OFF, NYLON LENGTH .3750 OD .250 #4 SCREW
B6797901 WIRING, POWER SUPPLY UPGRADE SPIN
P0006100 SCREW, 6-32 X .875 ROUND HEAD SLOTTED ZN
PP10023 SCREW, 10-24 X .375 SELF TAPPING
P0113300 SCREW, .250-20 X .500 HEX HEAD SST
PP10693 SCREW, 10-24 X .375 THRUSS HEAD PHILLIPS ZN
P0093300 NUT, HEX KEP .250-20 ZN
1
3
1
4
1
5
4
6
1
7
1
8
1
9
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
31
32
33
34
35
1
1
1
10
4
4
1
4
18
2
2
2
P0092500 NUTSERT, 10-24 UNC
2
P0091400 NUTSERT, 6-32 UNC
14
4
60092101 NUTSERT, 4-40 UNC
60044801 SCREW, SOCKET HEAD 2-56 X .375
A5626102 BASKET LIFT, SIDE INSERT BRACKET LH
A5626104 BASKET LIFT, SIDE INSERT BRACKET RH
B6795001 WIRING, SPINFRYER BASKET LIFT ASSEMBLY
60070601 SCREW, M3 X 0.5mm X 12mm
2
1
1
1
2
60127201 CAP,TAB .187 SERIES
2
A5626901 BRACKET, POWER SUPPLY SPIN BL
60180601 SHOULDER WASHER, SHORT BARREL #4
60180301 HEAT SINK, SPIN BL
1
4
1
60078502 CIRCUIT BREAKER, ROCKER DPST 250V 5A
1
L22-375 Rev 1 6/13, Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
8.3 Superseded Enclosure Assembly built before September 2012
See next page for parts list.
L22-375 Rev 1 6/13, Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Superseded Enclosure Assembly built before September 2012
SSH55
SG14
X
ITEM#
1
PART NO. DESCRIPTION
SE14 S*H50
B3335501 TANK, ENCLOSURE TOP WELDMENT
B3335502 TANK, ENCLOSURE TOP WELDMENT
B3335503 TANK, ENCLOSURE TOP WELDMENT
B3335601 TANK, ENCLOSURE SIDE WELDMENT LH
B3335603 TANK, ENCLOSURE SIDE WELDMENT LH
B3335605 TANK, ENCLOSURE SIDE WELDMENT LH
B3335602 TANK, ENCLOSURE SIDE WELDMENT RH
B3335604 TANK, ENCLOSURE SIDE WELDMENT RH
B3335606 TANK, ENCLOSURE SIDE WELDMENT RH
A3366202 TANK, ENCLOSURE FRONT
A3366302 TANK, ENCLOSURE MAGNET BOX BODY
A3366402 TANK, ENCLOSURE MOTOR BOX BODY
A3366404 TANK, ENCLOSURE MOTOR BOX BODY
60174301 MOTOR, STEPPER NEMA34 2.8A SURE STEP
60068317 O‐RING, VITON 3.063 OD, 2.875 ID
A5075001 COUPLE, DRIVE
X
X
2
3
X
X
X
X
X
X
4
5
6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
7
8
9
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
10
11
12
13
14
15
16
17
18
19
20
21
B5305001 ELECTRICAL ASSEMBLY, DVI
60022903 WASHER, FLAT #10 11 /16 OD SST
60022908 WASHER, FLAT #4 SST
60088011 SCREW, 4‐40 X .250 HEX HEAD SST
P0075400 SCREW, 10‐24 X .500 SELF TAPPING
PP11369
PP10950
SCREW, SOCKET HEAD .250‐20 X .750
SET SCREW, SLOTTED .250‐20 UNC, .375L
P0092500 NUTSERT, 10‐24 UNC
P0142000 NUT, ACORN WITH CENTERLOCK 10‐24 SST
60135703 BOLT, 10‐24 X 3/8 CARRIAGE SST
B2104601 TK COV, DMPR BRKT RR WLDMT
60088012 SCREW, 10‐24 X .375 HEX HEAD SST
L22-375 Rev 1 6/13, Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
8.4 Enclosure Assembly built after September 2012
See next page for parts list.
L22-375 Rev 1 6/13, Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Enclosure Assembly built after September 2012
B33354xx, Complete assembly
SG14
SSH55
-
ITEM NO.
PART NO.
DESCRIPTION
SE14 S*H50
1
1
B3335503 TANK, ENCLOSURE TOP WELDMENT S*H50 SPIN
B3335502 TANK, ENCLOSURE TOP WELDMENT SE14 SPIN
B3335501 TANK, ENCLOSURE TOP WELDMENT SG14* SPIN
B3335901 TANK, ENCLOSURE SIDE WELDMENT SG* SPIN LH
B3335903 TANK, ENCLOSURE SIDE WELDMENT SE* SPIN LH
B3335905 TANK, ENCLOSURE SIDE WELDMENT S*H50 SPIN LH
B3335906 TANK, ENCLOSURE SIDE WELDMENT S*H50 SPIN RH
B3335902 TANK, ENCLOSURE SIDE WELDMENT SG* SPIN RH
B3335904 TANK, ENCLOSURE SIDE WELDMENT SE* SPIN RH
A3366302 TANK, ENCLOSURE MAGNET BOX BODY SG* SPIN
A3366404 TANK, ENCLOSURE MOTOR BOX BODY SE* SPIN
A3366402 TANK, ENCLOSURE MOTOR BOX BODY SG* SPIN
60174301 MOTOR, STEPPER NEMA34 2.8A SURE STEP
60068317 O-RING, VITON 3.063 OD, 2.875 ID
-
X
-
-
X
-
1
X
X
-
-
2
-
-
2
X
-
-
2
-
X
X
-
3
-
-
3
X
-
-
3
X
X
X
-
-
4
X
-
X
X
-
5
5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
7
8
A5075001 COUPLE, DRIVE
9
B5305001 ELECTRICAL ASSEMBLY, DVI
10
11
12
13
14
15
16
17
18
60022903 WASHER, FLAT #10 SST
60022908 WASHER, FLAT #4 SST
60088011 SCREW, 4-40 X .250 HEX HEAD SST
PP10023 SCREW, 10-24 X .375 SELF TAPPING
PP11369 SCREW, SOCKET HEAD .250-20 X .750
P0092500 NUTSERT, 10-24 UNC
P0142000 NUT, ACORN WITH CENTERLOCK 10-24 SST
60135703 BOLT, 10-24 X .375 CARRIAGE SST
PP10950 SET SCREW, SLOTED .25-20 UNC, .375L
L22-375 Rev 1 6/13, Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
8.5 Superseded Cover & Damper Assembly built before September 2012
SG14
ITEM NO.
PART NO.
DESCRIPTION
SE14 S*H50
SSH55
1
2
3
3
3
B2104701 TANK COVER, DAMPER WITH FITTINGS
PP10263 SWITCH, PROXIMITY ACTUATOR
B2104401 TANK COVER, WELDMENT SG14*
B2104402 TANK COVER, WELDMENT SE14
B2104403 TANK COVER, WELDMENT S*H50
X
X
X
X
X
X
X
X
X
L22-375 Rev 1 6/13, Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
8.6 Cover Assembly built after September 2012
SG14
ITEMNO.
PART NO.
DESCRIPTION
SE14 S*H50
SSH55
B2104901 TANK COVER, WELDMENT SG14*
B2104902 TANK COVER, WELDMENT SE14
B2104903 TANK COVER, WELDMENT S*H50
X
1
2
X
X
X
X
B2105001 TANK COVER, BACK SUPPORT WELDMENT S*14 SPIN
X
B2105002 TANK COVER, BACK SUPPORT WELDMENT S*H50 SPIN
60135702 BOLT, 10-24 X .500 CARRIAGE SST
3
4
5
X
X
X
X
X
X
X
X
60022903 WASHER, FLAT #10 SST
P0142000 NUT, ACORN WITH CENTERLOCK 10-24 SST
L22-375 Rev 1 6/13, Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
8.7 Miscellaneous Parts
SG14R
SSH55
ITEM NO. PART NO.
DESCRIPTION
SG14
SE14 S*H50
B5609901 BASKET LIFT, TOP PLATE ASSEMBLY SG14R, SSH55
B5609902 BASKET LIFT, TOP PLATE ASSEMBLY SG14
B5609903 BASKET LIFT, TOP PLATE ASSEMBLY SE14
B5609904 BASKET LIFT, TOP PLATE ASSEMBLY S*H50
60088003 SCREW, .250‐20 X .750 HEX HEAD SST
A5624902 BASKET LIFT, ROD SG SPIN
A3366502 TANK, ENCLOSURE MOTOR COVER SG* SPIN
A3366504 TANK, ENCLOSURE MOTOR COVER SE* SPIN
60176901 HINGE, LIFT OFF BRIGHT CHROME TYPE A
60176902 HINGE, LIFT OFF BRIGHT CHROME TYPE B
B2104702 TANK COVER, DAMPER WITH FITTINGS
B2104701 FOR UNITS BUILT PRIOR TO 9/2012
OBSOLETE, REPLACE WITH ITEM1
X
X
1
X
X
X
X
2
3
X
X
X
X
X
X
X
X
4
X
X
X
X
X
X
X
X
5
6
X
X
X
X
X
X
7
8
X
X
X
X
L22-375 Rev 1 6/13, Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
8.8 Basket Assembly
B4516001 Entire assembly (Blue Handle)
ITEM NO. PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
B4515303 WIRE GOODS, BEARING BASKET HANDLE WELDMENT BLUE
B4515304 WIRE GOODS, BEARING BASKET HANDLE WELDMENT GREEN
60183801 TAPERED ROLLER BEARING ASSEMBLY, BEARING 1.375 O.D. X .500 I.D.
60183901 TAPERED ROLLER BEARING ASSEMBLY, OUTER RING (RACER) 1.375 O.D. X .500 I.D.
60183501 NUT, SLOTTED HEX (CASTLE) .50-13 THREAD
6NT202 PIN, SST COTTER .125 DIA. X 1.25 LG.
B4515801 WIRE GOODS, SPIN BASKET DRIVE POST ASSEMBLY
B4515901 WIRE GOODS, SPIN BASKET WELDMENT
L22-375 Rev 1 6/13, Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
8.9 Bottom Assembly
B5608802 Entire assembly
ITEMNO. PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
PP10665 SCREW,10-24 X .375 RDH SST
60088013 SCREW, 10-24 X .625 HEX HEAD SST
60088012 SCREW, 10-24 X .375 HEX HEAD SST
60177401 SCREW, OVAL 82 DEG X .375 SST
B5609001 LIFT PLATE
A5625402 LIFT PLATE, PIVOT BAR
A5625302 LIFT PLATE,BLOCK
A5625502 LIFT PLATE STOP
60022906 WASHER, FLAT #10 X 1.00 X .125 THK SST
L22-375 Rev 1 6/13, Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
8.10Splash Back Assembly
B41043xx Entire assembly
SG14
SSH55
ITEM NO. PART NO.
DESCRIPTION
SE14
SGH50
X
SEH50
X
A4113102 SPLASH BACK, SPIN SG14* SINGLE
X
A4113108 SPLASH BACK, SPIN SEH50 SINGLE
A4113106 SPLASH BACK, SPIN SGH50 SINGLE
A4113104 SPLASH BACK, SPIN SE14 SINGLE
A5625702 BASKET LIFT, ROD GUIDE BOXBODYSG14* SPIN
A5625704 BASKET LIFT, ROD GUIDE BOXBODYSE14* SPIN
A5625706 BASKET LIFT, ROD GUIDE BOXBODYS*H50 SPIN
A5625002 BRACKET, ROD BEARINGS
1
2
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
3
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
A5626702 RING, ROD BEARINGS INNER BOT
60054903 BEARING, PTFE .5 ID
5
6
A5626602 DEFLECTOR, ROD GUIDE
7
P0092500 NUTSERT, 10-24 UNC
8
P0075400 SCREW, 10-24 X.500 SELF TAPPING
A5625202 RING, ROD BEARINGS INNER
9
10
11
12
13
14
A5625102 RING, ROD BEARINGS
60132001 TANK, STUD SPLASH BACK SCREW ON
P0112000 SCREW, 10-24 X .500 HEXHEAD SST
60118201 SCREW, .250-20 X .375 HEX FLANGED HEAD SST
P0142000 NUT, ACORN WITH CENTERLOCK 10-24 SST
X
X
X
X
L22-375 Rev 1 6/13, Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Basket Lift Wiring Diagram
L22-375 Rev 1 6/13, Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Schematic
L22-375 Rev 1 6/13, Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
L22-375 Rev 1 6/13, Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes:
L22-375 Rev 1 6/13, Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
In the event of problems with or questions about
your order, please contact the Factory at:
In the event of problems with or questions about
your equipment, please contact the Pitco
Authorized Service and Parts representative
(ASAP) covering your area, or contact Pitco at
the number listed to the left.
+001 (603) 225-6684 (World Wide)
MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501
SHIPPING ADDRESS – 10 FERRY ST., CONCORD, NH 03301
SPINFRESHTM is a trademark of Spinfry inc.
L22-375 Rev 1 6/13, Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
|