10.4" Flip Down TFT-LCD Color
Monitor with IR
PLVW1045R
Download from Www.Somanuals.com. All Manuals Search And Download.
1. INSTALLATION GUIDE
1. On a towel or soft cloth, gently place the monitor unit "face
down" on a stable work surface.
2. Locate the pigtail with the DIN connector.
3. Connect the DIN connector to the interface cable provided.
4. Connect the RED wire th the positive (+) battery terminal.
5. Connect the Black wire to a chassis electrical ground point.
6. Connect the cable with YELLOW RCAjack to Video Input
sources for your Video Program material.
7. Connect the cable with RED and WHITE RCA jack to Audio
sources for your Audio Program material.
Yellow
RED
AV1
WHITE
Yellow
RED
AV2
WHITE
Red wire to +12VDC battery
Black wire to electrical ground
2
Download from Www.Somanuals.com. All Manuals Search And Download.
2. FUNCTION KEYS
2.1 FUNCTIONS OF FRONT PANEL
1. Press the "POWER" button once, it will be "POWER ON."
POWER:
MENU:
Press it again, it will be "POWER OFF."
1. Pop up the OSD menus. Press the "Menu" button again to
enter the OSD menus. When in sub-menu, press.
"EXIT" to go back to the main menu.
UP/DN:
1. Press the "UP/DOWN" key to increase or decrease value
2. Make item selection in OSD menus to increase or decrease
parameters as well..
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 FUNCTIONS OF REMOTE CONTROL
POWER
Inc / Dec KEY
MENU
MENU
MUTE
AV1/AV2
REMOTE CONTROLLER
Brightness:
Brightness, contrast adjustment
RGB color density, deviation, sharpness
adjustment
Video Control:
OSD Function:
Image:
OSD adjustment and display methods
Switch the source of signal AV1 and AV2
Inputs.
Audio:
Recall:
Exit:
Only control Mute
Return to the initiatives
Exit
PRess "Menu key", it will display a crosswise bar with digits. To
use U/D key to adjust value and press "Menu key" to confirm the
adjustment and then the crosswise bar and digits will disappear, or
press "Exit" to leave OSD function directly.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3. TROUBLE SHOOTING
3.1 NO POWER
1. Make sure the power cable has been pluged in.
2. Make sure the plug has 12V~14V, may use another
electrical appliance to test it.
3.2 NO FUNCTION OF REMOTE CONTROL
1. Make sure the batteries are in good condition and installed
properly.
2. Make sure the remote control is aiming at the receiver, and
there are no obstacles in between.
3. Perhaps, it is too far away from the receiver. Normal
distance is within 7 meters.
3.3 NO DISPLAY OR NOT CLEAR
1. Check the video signal wires if they are connected
properly.
2. Make sure the TV/Video is in proper position.
4. ACCESSORIES
PS2/CAR CABLE
INSTALLATION BRACKET
SCREW PACK
USER MANUAL
REMOTE CONTROL
5
Download from Www.Somanuals.com. All Manuals Search And Download.
5. SPECIFICATIONS
DESCRIPTION
10.4" a-Si TFT active matrix
26.4cm diagonal (10.4 inch)
640(H) x 3(RGB) x 480(V)
165(W) x 95(H)
ITEM
LCD Panel Type
Screen Size:
Display Resolution (dot):
Active Area:
Pixel Pitch:
0.33(H) x 0.33(V)mm
CCFL (Cold cathode filament tube)
4 : 3
Back Light:
LCD Profile Ratio:
Contrast Ratio:
Brightness:
200 : 1
220 cd/m2
+
Power Input Consumption:
System:
DC12V 10% less than 0.8A
-
NTSC and PAL auto switch
SCEAM is available
Composite video signal 1Vp-p 75 ohms
PS2 x 2
Video Input:
Video Input:
Viewing Angle:
Lift & Right 45 degree
Down 20 degree Top 30 degree
265.0mm(W) x 268mm(H) x 40.8mm(D)
0 C ~ +60 C
Dimensional Outline (mm):
Operation Temperature:
Storage Temperature:
Humidity:
-20 C ~ +80 C
10 ~ 90%
Monitor Weight:
1.8kg
Safety Certifications:
Monitor Rotate:
UL FCC CE TUV
Right 90 & Left 90
* Recommend for use with PYLE'S PLVWH1 wireless headphones.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
|