MN-800-TF
REVERSE OSMOSIS TREATMENT SYSTEM
OWNERS MANUAL
Nimbus Water Systems
41840 McAlby Court, Suite A
Murrieta, CA 92562-7036
800-451-9343
Download from Www.Somanuals.com. All Manuals Search And Download.
THE NIMBUS MN-800 TF REVERSE OSMOSIS TREATMENT SYSTEM
The Nimbus MN-800 TF is the perfect system for a wide variety of applications. Features include
stainless steel pressure vessels, frame and concentrate recirculation valve. There are pressure
gauges on the pre-filter outlet, post-filter inlet and the high pressure outlet of the desalinator array.
The MN-800 TF is also equipped with a 20" 10µ (micron) carbon cartridge pre-filter and post-
filter. An Auxiliary 10” Post Filter with a Calcite element is included in the product line of one
desalinator. MN-800 TF systems have a nominal production rate of 800 gallons per day.
§1.0 MN-800 TF SYSTEM SPECIFICATIONS
MODEL NO.
MN-800 TF
Thin Film
2 (2525)
Membrane Type
No. of Desalinators
Production Rate † (GPD)
Production Rate † (ml/min)
Maximum Operating Pressure (PSI)
Maximum Recovery
800
2,103
200
33%
Electrical Supplies
110V/60 Hz
220V/60 Hz
11.0 A
5.2 A
Motor Rating
Pump Model
Dimension
Weight
3/4 HP
2504 A
42”H x 19”W x 16”D
84 lbs
†
Production rates are based on 200 psi net working pressure at 77 F with feed water containing 1000 ppm
NaCl. Flow tolerances are ± 15%.
°
§2.0 SYSTEM COMPONENTS (See Figure 1)
DESALINATOR: This is where the dissolved solids are separated from the feed water. This
assembly consists of a 316 stainless steel pressure vessel that houses the reverse osmosis (RO)
membrane. The MN-800 TF models come equipped with a Thin Film (TF) Membrane.
PUMP/MOTOR ASSEMBLY: The rotary positive displacement pump boosts water pressure in the
desalinator to about 185 psi (12.8 bar) to ensure high solids rejection and high flow rates.
SOLENOID VALVE: Electrically operated valve that prevents water from flowing through the
system when it is not in operation.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONCENTRATE RECIRCULATION VALVE: A needle valve that controls the amount of
concentrate from the desalinator array to be recirculated back into the feed stream. This feature
allows for higher recovery rates. Additionally, adjustment of this valve regulates the pump
discharge pressure.
FLOW CONTROL: A fixed orifice that controls the amount of water flowing across the membrane
to drain.
PRODUCT WATER CHECK VALVE: A one-way valve that prevents pressurized product water
from flowing back into the desalinator (and possibly damaging the membrane) when the system is
off. There is a check valve in the product line for each desalinator.
SYSTEM PRESSURE GAUGE: A glycerin filled gauge that displays the operating pressure in the
desalinator.
TANK PRESSURE GAUGE (Option): A gauge that displays product water pressure when using a
pressurized storage tank.
WATER SUPPLY PRESSURE GAUGE: A gauge that displays the water pressure of the feed
water source.
FILTER PRESSURE GAUGE: A gauge that displays the water pressure after the carbon cartridge
pre-filter. This is used to observe the pressure drop through the sediment pre-filter (a means of
detecting filter clogging or loading).
LOW PRESSURE SWITCH: An electrical switch that shuts off the unit in the event of low feed
water pressure. This is used as a pump protection device. This is factory set to cut off at 12 psi
(0.8 bar). This switch is the one mounted on the manifold and behind the sediment pre-filter.
TANK PRESSURE SWITCH: An electrical switch, used with a pressurized storage tank that
controls the system operation based on the storage tank pressure. This is factory set to shut the
system off when the tank pressure is 60 psi (4.1 bar) and turn the system on when the tank
pressure is below 40 psi (2.8 bar). This switch is the one mounted on the manifold and behind the
carbon post-filter.
PRE-FILTER CARBON CARTRIDGE ASSEMBLY: A 20” 10 micron filter that reduces chlorine in
the feed water.
POST-FILTER CARBON CARTRIDGE ASSEMBLY: A 20” 10 micron carbon cartridge filter that
helps remove bad taste and odor. This filter is used with pressure storage systems. A tank
pressure switch and check valve are always included with operation with a pressure tank storage
system.
POST-FILTER ASSEMBLY: A 10” housing. This filter is used with a Calcite element to neutralize
the pH of the product water.
TANK PRESSURE RELIEF VALVE: This valve limits the product pressure tank to 80 psi as a
precaution.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ANCILLARY EQUIPMENT:
The following items are also covered in this manual to form a complete water treatment system.
PRESSURE TANK: The tank provides storage for approximately 34 gallons of treated water at a
pressure of 40 to 60 psi.
REMOTE BY-PASS PANEL: This panel monitors treated water TDS and storage tank pressure.
It includes a valve for switching to delivery of city water to the food service machines in the event
of an RO system failure.
INSTALLATION KIT: This kit contains fittings, tubing earthquake restraints and hardware for the
assembly, installation and connection of all components.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
§3.0 PRE-INSTALLATION PROCEDURES
PLEASE READ CAREFULLY. FAILURE TO FOLLOW THESE PROCEDURES CAN RESULT IN
DAMAGE TO YOUR SYSTEM AND VOID YOUR WARRANTY.
§3.1 PACKAGING
Upon delivery, inspect packaging for damage and report it to your carrier at that time. After
unpacking the system, inspect it carefully for signs of damage. All damage claims should be
made to the delivery carrier.
§3.2 OPERATING LIMITATIONS
Nimbus MN-800 TF units are to be used on potable water only. The user must be sure that water
to be treated is both microbiologically safe and non-toxic. Ensure that the operating parameters
outlined in §3.3 are met at the installation site. Items of most importance are TDS, feed water
pressure, flow rate, chlorine level and temperature range. A water analysis is helpful in
determining if any pre-treatment is needed. If your water analysis shows levels of substances in
excess of the maximums stated in §3.3, contact the Nimbus factory for pre-treatment
recommendations.
§3.3 OPERATING PARAMETERS
MODEL NO.
MN-800 TF
Thin Film
Membrane Type
Feed Pressure
15-100 psi
(1.0 – 5.9 bar)
Maximum Feed Flow Rate
Maximum Temperature
Maximum Chlorine (continuous)
Maximum Total Dissolved Solids (TDS)
pH Range
2.75 GPM
122 F (50C)
°
1.0 ppm
5,000 ppm
4.0 - 11.0
0.0 ppm
Iron
Hydrogen Sulfide
0.0 ppm
Manganese
0.0 ppm
pH Range (optimum rejection)
Turbidity
Silt Density Index
5.0 - 8.0
< 1.0 NTU
< 5.0 SDI
7
Download from Www.Somanuals.com. All Manuals Search And Download.
§4.0 INSTALLATION
PLEASE READ CAREFULLY BEFORE BEGINNING INSTALLATION. FAILURE TO FOLLOW
THESE PROCEDURES CAN RESULT IN DAMAGE TO YOUR SYSTEM AND VOID YOUR
WARRANTY.
§4.1 LOCATION
It is recommended that systems be located where they are protected from harsh environments
such as rain, snow and extreme temperatures (both hot and cold). MN-800 TF units can be
located just about anywhere there is a water and electrical supply. This can be on the floor,
mounted on the wall with a shelf, or any other flat surface. Keep in mind, however, that they
should be out of normal traffic patterns and should be easily accessed for daily monitoring and
service.
§4.2 SYSTEM PLUMBING INSTALLATION GUIDE LINES
A complete plumbing diagram of the system installation is shown in Figure 2. Always abide by
local plumbing codes when installing the system. We recommend that a licensed plumbing
contractor install this system. When installation procedures conflict with your local plumbing
codes, STOP and contact Nimbus. This installation guide assumes the appropriate electrical
outlet, 2 city water valves (1/2” FPT) and 1 valve (1/2” FPT) for distribution to the food service
machines have been installed convenient to the system installation location. All threaded fittings
are to be installed with Teflon tape.
FOR PLASTIC TUBING, USE ONLY SUPPLIED NYLON FERRULES AND
IMPORTANT:
BRASS TUBE INSERTS. DO NOT USE BRASS FERRULES ON PLASTIC TUBING.
:
§4.2.1 TANK PREPARATION AND INSTALLATION
Install the 1-¼” x ¾” bushing In the 1-¼” FPT fitting at the bottom of the tank then install the ¾”
MPT x 5/8” compression elbow in the bushing. Direct the 5/8” compression end toward the
opening in the tank skirt. Cut a piece of black 5/8” tubing to extend about 4” beyond the tank
skirt. Then install the tubing into the 5/8” compression fitting on the tank outlet.
Follow the instructions included with the tank wall brace kit to secure the tank to the rear wall.
Locate the restraint brackets about 15” and 30” above the floor. Set the tank in place and
rotate it so the bottom tank outlet is positioned as desired. Tighten the bracket clamps securely
around the tank.
Remove the blue protective cap from the nut on top of the tank. Install the 5/8” x 1-½” long stud
in the nut. Install the black plastic feet on the legs of the RO frame then lift and place the RO
system on top of the tank with the threaded stud extending through the hole in the center of the
RO frame base. Install the flat washer and nut on the stud. Rotate the RO so there is access
to the 20” filters on the front of the unit. Tighten the 5/8” nut to secure the RO to the tank.
Install the ½” ball valve on the 5/8” tubing on the outlet of the tank. Use one straight and one
elbow of ½” MPT x 5/8” compression fitting. With these fittings the valve can be installed
straight out from the tank or pointing vertically up the side of the tank as desired. Connect a
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
piece of black 5/8” tubing from the valve up to the 5/8” compression fitting at the back right side
of the RO system manifold.
:
§4.2.2 BY-PASS PANEL PREPARATION AND INSTALLATION
The by-pass panel is to be located convenient to the RO where the TDS monitor is visible and
the valve can be operated without difficulty.
The standard fittings provided are ½” MPT x 5/8” compression to be installed directly in the 3 ½”
FPT ports at the bottom of the panel. Three ½” street elbows are also provided to allow the
option of mounting the by-pass panel closer to a floor surface if desired.
Referring to the front view of the panel: the fitting marked FEED (Left side) will be connected to
a city water valve, the fitting marked USAGE (center) will be connected to the valve feeding all
food service machines, the fitting marked FROM RO (right Side) will be connected to the RO
unit Post filter fitting marked FAUCET.
Two ½” MPT x 5/8” compression fittings are also provided for the 2 valves indicated above.
Make all 3 connections using the 5/8” black tubing provided.
:
§4.2.3 RO FEED WATER CONNECTION
A ½” MPT x 5/8” compression fitting is provided to connect a city water feed valve to the RO
feed water filter inlet Marked FEED. Install the fitting in the valve and connect to the RO using
the 5/8” black tubing provided.
:
§4.2.3 RO DRAIN CONNECTIONS
3/8” white plastic tubing is used to connect the brine outlet to a drain and the product high
pressure relief valve to drain. The fittings are the quick connect type and are marked DRAIN.
It is suggested the product high pressure relief valve be connected to drain via an air gap
device (not supplied) so that any flow, although unlikely, would be diverted to drain. The
opening of this valve and subsequent water flow is an indication of a system malfunction, most
likely in the tank pressure switch.
§4.3 ELECTRICAL
A complete electrical diagram of the RO system is shown in Figure 3.
THE SYSTEM MAY START WHEN POWER IS APPLIED. DO NOT CONNECT
WARNING!
POWER UNTIL THE SYSTEM IS COMPLETELY INSTALLED AND READY TO RUN.
In the U.S., MN-800 TF systems come with a standard 115V three-prong plug. When wired for
220V, the systems have only bare leads for either hard wiring to a disconnect switch or for
installation of the proper plug. Be sure the receptacle you use is on a circuit that has a Ground
Fault Interrupter (GFI) and has sufficient capacity for the operating current as listed in §1.0
SYSTEMS SPECIFICATIONS. It is recommended that the unit be installed on a dedicated circuit
to prevent overloading on system start-up. The power cord on the MN-800-TF is 10 feet long.
The electrical outlet must be located accordingly.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
§5.0 SYSTEM FLUSH AND PERFORMANCE VERIFICATION
Although MN-800-TF systems are fully tested at the factory prior to shipping, it is recommended to
flush and verify your system's performance on-site.
§5.1 SYSTEM FLUSH AND OPERATION
New membranes have a preservative on them that needs to be flushed before use.
Open the fast flush valve and all usage outlets to allow product to run to drain.
Fully open the concentrate recirculation valve by turning the knob counterclockwise.
Insure the valve on the By-Pass Panel is in the NORMAL position.
•
•
•
•
Turn on the water supply to the unit and check for leaks up to the solenoid valve (just after
the feed water filter outlet).
Plug the system into an electrical outlet.
IMMEDIATELY.
CAUTION! THE SYSTEM WILL START
•
•
After the system has run for a few minutes to clear any air, turn the concentrate
recirculation valve clockwise to close then open a quarter turn.
FLUSH VALVE IS OPEN.
BE SURE THE
CAUTION!
Allow the system to flush for one hour with all water discharged to drain. Open the
concentrate recirculation valve then close the flush valve. Gradually turn the concentrate
recirculation valve clockwise until the system pressure gauge reads 180 psi (12.4 bar).
•
•
Check for leaks and check the system pressure gauge. It is likely that the system
pressure will drift from 180 psi (12.4 bar) during this first high pressure run time, if it does
turn the concentrate recirculation valve clockwise to increase pressure or counterclockwise
to decrease pressure.
DO NOT LET SYSTEM PRESSURE RISE ABOVE 200
CAUTION:
PSI (14 BAR) AS DAMAGE CAN OCCUR.
Insure the ball valve on the tank outlet is open. Allow the system to make product for at
least 5 minutes then check the TDS of the product by pressing the red button on the
Monitor in the By-Pass Panel, the Green LED should light.
•
•
•
Close all food service machine valves. The unit will now make product water, which will go
to the pressurized storage tank. Observe a gradual rise in the product gauge on the RO
unit or on the BY-Pass Panel. Allow the tank pressure to rise.
As the product pressure increases check for leaks in all product plumbing. When the
product tank pressure reaches about 60 psi the RO should turn off, this could take one
hour or more. Open a food service valve and observe a gradual drop in the tank pressure
from 60 psi. When the pressure drops to about 40 psi the RO should come back. Close
the food service valve.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
As a final check turn on the city water valve to the By-Pass Panel and check the plumbing
for leaks.
•
§5.2 PERFORMANCE VERIFICATION
Factory test data is supplied with the system. To ensure optimum performance, on-site data
should be taken and compared to the factory test data. This data should be taken after the
system has been flushed for one hour. Some deviations may be seen due to differences in feed
water TDS and temperature between the site and factory. If you have already connected the
product line to the tank, you will need to disconnect it ahead of the post carbon filter (if one is
installed) to take product samples.
The following tests need only be performed if it is felt the system may not be performing as
expected. The flow and TDS tests may be performed say after membrane replacement. The
pressure switch tests can be performed periodically to insure operation at the preferred set points.
§5.2.1 FLOW TESTS
Determine the flow rates for both product and concentrate. Put the product line into a container
and measure the volume of water that flows into it in one minute. Repeat the process with the
concentrate (drain) line. These values should be in either gallons per minute or milliliters per
minute. Product flow rates (at 77 F, 25 C) should be within 15% of the production rates given in
°
°
§1.0 SYSTEM SPECIFICATIONS.
§5.2.2 CONCENTRATE TO PRODUCT RATIO
Compute the concentrate to product ratio (C:P) by dividing the concentrate flow rate by the
product flow rate. This ratio should be between 2:1 and 5:1.
§5.2.3 TOTAL DISSOLVED SOLIDS (TDS) REJECTION
Using a conductivity meter (TDS meter) measure the TDS in both the feed water and the product
water. Calculate percent rejection using the formula below:
(Feed TDS-Product TDS) (Feed TDS) 100 = % Rejection
÷
×
Rejection should be 85% or better. For example, where the feed TDS is 600 and the product TDS
is 24, the percent rejection is
600-24) 600 100 = 96%.
÷
×
§5.2.4 LOW PRESSURE SWITCH TEST
While the system is running gradually shut off the water supply to the system and observe the
feed water filter gauge. The system should shut off when the pressure drops to about 12 psi. If
the system does not shut off, either unplug the system or restore the water supply to the system.
DO NOT LET THE SYSTEM RUN WITHOUT THE WATER SUPPLY TURNED ON. PUMP
DAMAGE WILL OCCUR. Refer to §7.1.1 for LOW PRESSURE SWITCH ADJUSTMENT.
§5.2.5 TANK PRESSURE SWITCH TEST
With the product line connected to the tank and with the system running, close the inlet valve to
the tank. The tank pressure gauge should start to rise and the system should shut off when the
13
Download from Www.Somanuals.com. All Manuals Search And Download.
gauge reads about 60 psi (4.1 bar). Now, by opening the tank inlet valve the tank pressure should
begin to drop and the system should turn on when the pressure drops below about 40 psi (2.8
bar). If the system fails to shut off at 60 psi (4.1 bar), watch the gauge and be sure that it does
not rise above 80 psi (5.5 bar). If it reaches 80 psi (5.5 bar), unplug the system. Refer to §7.1.2
for TANK PRESSURE SWITCH ADJUSTMENT.
§6.0 OPERATION AND MAINTENANCE
Nimbus MN-800-TF systems are designed for simple operation with little user intervention.
Nimbus recommends keeping accurate performance records and following a regular preventative
maintenance schedule to maximize the life of your system. A performance record sheet is
provided at the back of this manual for you to copy and keep near your system. This record sheet
will be important for warranty verification, trouble shooting as well as possibly suggesting more or
different pre-treatment.
§6.1 DAILY SYSTEM CHECKS
Your water supply pressure can vary from time to time. This can also affect your system
operating pressure. Therefore, it is recommended to check and adjust your system pressure daily
to ensure maximum water production rates and quality. Check both the water supply pressure
gauge and the filter pressure gauge. Under normal conditions, there should be a 3-5 psi
difference between the two gauges. When the difference reaches 10 psi, a pre-filter change is
recommended. See §7.4 PRE FILTER CARBON CARTRIDGE REPLACEMENT for further
discussion.
§6.2 MONTHLY SYSTEM CHECKS
In addition to the daily checks the procedures in §5.2 PERFORMANCE VERIFICATION may be
performed, record all data on your performance record sheet.
§6.3 QUARTERLY SERVICE
It is recommended to change both sediment and carbon filter cartridges at least every 3 months.
Carbon cartridges should be changed more often if bad taste and/or odor become evident. The
pre-filter carbon cartridge should be changed more often if water supply pressure and filter
pressure gauges differ by 10 psi or more, or if the Chlorine content of the city water is higher than
0.2 ppm.
§6.4 PERIPHERAL EQUIPMENT
Peripheral equipment such as pre-filters, post-filters and tanks also have periodic maintenance
requirements. It is essential to maintain these as they can have a dramatic effect on the
performance of your system. Refer to their specific manuals for proper maintenance procedures.
§7.0 SERVICE
§7.1 LOW PRESSURE SWITCH ADJUSTMENT
The low pressure switch is factory set to turn the system off if feed pressure drops below
12 psi (0.8 bar). This switch can be adjusted to as low as 3 psi (0.2 bar) and as high as 20
•
14
Download from Www.Somanuals.com. All Manuals Search And Download.
psi (1.4 bar).
Before servicing, always disconnect power to the unit to avoid shock.
To adjust, remove cover and refer to the diagram inside the cover.
•
•
•
Turn adjustment nut #1 counterclockwise to decrease cut-out pressure and clockwise to
increase cut-out pressure. Under normal circumstances it is not necessary to adjust this
switch setting.
Replace cover and restore power to unit.
•
ALWAYS BE SURE TO CHECK THE CUT-OUT OPERATION AFTER ADJUSTMENT AS
OUTLINED IN §5.2.4 LOW PRESSURE SWITCH TEST.
§7.2 TANK PRESSURE SWITCH ADJUSTMENT
The tank pressure switch is factory set to turn the system off when the tank pressure reaches 60
psi (4.1 bar), called the cut-out setting. The system will then restart when the tank pressure drops
below 40 psi (2.8 bar), called the cut-in setting. The difference between the two is referred to as
the differential. The cut-in can be set as low as 5 psi (0.3 bar) and the cut-out can be set as high
as 65 psi (4.5 bar), however the differential range is limited to 10-30 psi (0.7-2.0 bar).
Before servicing, always disconnect power to the unit to avoid shock.
•
•
To adjust the differential, remove cover and refer to the diagram inside the cover. Turn
the nut #2 counterclockwise to decrease cut-in pressure (the cut-out is held constant).
This increases the differential. Turn clockwise to decrease the differential range.
Once the differential range is set, turn nut #1 clockwise to increase BOTH the cut-in and
•
•
cut-out pressures together (the differential is held constant).
counterclockwise decreases both together.
Turning the nut
Replace cover and restore power to unit.
ALWAYS BE SURE TO CHECK THE CUT-OUT OPERATION AFTER ADJUSTMENT AS
OUTLINED IN §5.2.5 TANK PRESSURE SWITCH TEST.
§7.3 MEMBRANE REPLACEMENT (see Figure 4)
Nimbus recommends membrane replacement when the TDS rejection falls below 70%.
A
properly maintained and operated system may possibly get 2+ years out of a membrane. Your
system may require more frequent membrane changes depending on your feed water.
Before servicing, always disconnect power to the unit to avoid shock.
Close feed water and tank valves.
•
•
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Tag and disconnect the three tubing connections on the desalinator namely the feed,
concentrate and product.
•
Unsnap the desalinator retainers and pull desalinator(s) out.
•
•
Remove retaining clips from ends of desalinator by tapping the open ends of the clips with
a plastic or rawhide mallet until they are through the slots in the pressure vessel. Pull
clips completely out of pressure vessel.
Remove end plugs by gently pulling on the fittings. Do not use pliers on the fitting threads
because the threads might get damaged. As a suggestion, attach a scrap piece of tubing
(with a nut, a ferrule and an insert), and then use the tubing as a handle. See §8.0
PARTS & ACCESSORIES for end plug pulling tool.
•
Push membrane out of pressure vessel from the feed end.
•
•
Discard old membrane. Be careful not to discard the gray closed-end plug or the product
inter-connector.
Clean vessel and plugs with a mild detergent soap and rinse thoroughly.
•
•
Inspect all O-rings for cracks or nicks, replace as necessary. Lubricate O-rings with an
appropriate petroleum or silicone-based lubricant.
Install new membrane into the feed end of vessel (in the direction shown in Figure 4). Be
sure to note the end with the brine seal.
•
•
•
•
•
Install closed-end plug into vessel feed end plug, and product inter-connector into the
vessel concentrate/product end plug.
Install end plugs into their proper ends. IF END PLUGS ARE INSTALLED ON THE
WRONG ENDS THE SYSTEM WILL NOT OPERATE PROPERLY.
Install retaining clips and mount desalinator onto frame using tabs and install the retaining
clips.
Connect feed, concentrate, and product lines to their proper ports.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Since the membrane is new it will need to be flushed and tested. Follow procedures
outlined in §5.0 SYSTEM FLUSH AND PERFORMANCE VERIFICATION.
•
§7.4 PRE FILTER CARBON CARTRIDGE REPLACEMENT
Before servicing, always disconnect power to the unit to avoid shock.
Close feed water and tank valves.
•
•
•
Activate the switch on the side of the gray box in the back of the unit just enough to relieve
any pressure in the filter.
Remove pre-filter sump by turning clockwise (as viewed from the top). A filter wrench may
be necessary.
•
•
Remove cartridge and inspect. If cartridge is extremely silted, you should consider
changing more often. Discard old cartridge.
Take O-ring from seat in sump and inspect for cracks or nicks, replace as necessary.
Inspect sump for cracks, especially in the threaded area. Replace as necessary.
Lubricate O-ring with an appropriate lubricant. Install O-ring into its seat in sump.
Install new sediment cartridge.
•
•
•
•
•
Replace sump by screwing it onto cap in a counter-clockwise direction (as viewed from
top). A wrench should not be needed. Hand tightened is sufficient.
Restore water and power; check for leaks.
•
§7.5 POST-FILTER CARBON CARTRIDGE REPLACEMENT
Before servicing, always disconnect power to the unit to avoid shock.
Close feed water and tank valves.
•
•
•
Open faucet or disconnect line from "FAUCET" connection to relieve pressure from the
carbon filter.
Remove post-filter sump by turning clockwise (as viewed from the top). A filter wrench
may be necessary.
•
Remove and discard old cartridge.
•
•
Remove O-ring from seat in sump and inspect for cracks or nicks, replace as necessary.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Inspect sump for cracks. Replace as necessary.
•
•
Lubricate O-ring with an appropriate petroleum or silicone-based lubricant. Install O-ring
into its seat in sump.
Install new carbon cartridge with the white rubber ring up.
•
•
Replace sump by screwing it onto cap in a counter-clockwise direction (as viewed from
top). A wrench should not be needed. Hand tightened is sufficient.
Restore water and power; check for leaks.
•
●
Note: New carbon cartridges need to be flushed after being installed. After installation,
open faucet to allow tank water to flush out carbon fines. This water will be black at first.
Allow to flush until water runs clear.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
§8.0 PARTS AND ACCESSORIES
PART NUMBER
DESCRIPTION
Motor, ¾ HP
Clamp, V Band
Pump, 165 gph, Brass
ITEM
MOTORS & PUMPS
102612
101168
101199
DESALINATORS,
MEMBRANES &
HOUSINGS
104459
100716
104167
104157
104159
104198
104186
100036
Desalinator, TF, Complete (MN-800 TF & MN-800 TF)
Membrane, AG2525 (High Rejection)
Pressure Vessel, Stainless Steel
Interconnector, Product End, w/ORings
Interconnector, Closed End, w/ORings
Product End Plug
Closed End Plug
Retainer Clips, Desalinator (2 per)
PRESSURE SWITCH 105805
Solenoid Valve Coil, 120 VAC
Solenoid Valve Coil, 220/240 VAC
Solenoid Valve Body, ½”
Switch, Low Pressure Cut-Out
Switch, Tank Pressure
Pressure Gauge, System, 0-300 psi
Pressure Gauge, 0-100 psi
Valve, Concentrate Recirculation
Flow Control Union
Check Valve, Product Water 6F6M
TDS Monitor in remote bypass
Plug, Brine Flow Control, Delrin
GAUGES & FLOW
CONTROLS
105806
105807
105031
105030
101167
103248
101171
102619
100556
100732
100297
PRE-FILTER,
POST-FILTER
HOUSINGS &
FILTERS
100298
100553
100802
100730
103031
Filter Housing Assembly, 20", ¾” ports
Filter Housing Assembly, 10", 3/8 ports
O-Ring, Filter Housing
Carbon Cartridge, 20" 10µ
Calcite Cartridge, 10"
ANCILLARY
100807
100897
104137
104096
Pressurized Storage Tank (w/o valve), 34 Gallon
Filter Wrench
Installation Kit (For unit, tank, and remote by-pass)
Remote By-Pass Unit
20
Download from Www.Somanuals.com. All Manuals Search And Download.
§9.0 ATTACHMENTS
§9.1 REMOTE BYPASS SYSTEM INSTRUCTIONS
Indication – When water is required even though RO product water of the desired quality is not
available. This unit allows for the supply of feed water to supplement the RO water
requirement.
Installation – See the diagram below for plumbing the system. As a minimum, use tubing of at
least the RO product water outlet connection size. The feed water source for this unit should
have a valve that controls the flow rate to the storage tank when in the emergency mode of
operation.
Mount the unit on a wall convenient to the RO system and the product water storage system.
This unit is intended for use with pressurized product storage tanks.
If an atmospheric storage tank is used it must be equipped with a float actuated shutoff valve
as well as a float switch for control of the RO system. The float valve will prevent tank overflow
when in the emergency mode.
Operation – See the included instructions for TDS monitor setup and operation. If product
water TDS is found to be high, the selector valve can be used to the emergency position to
supply feed water to storage or usage while servicing the system. When the RO system
service is complete, the handle is returned to the normal position and the RO turned on.
Replacement Parts
100732
100886
101008
101295
101298
Complete TDS monitor
Battery
3-way ball valve
Check valve
Gauge
21
Download from Www.Somanuals.com. All Manuals Search And Download.
§9.2 TDS MONITOR INSTRUCTIONS
Model TDS-2B TDS Monitor
Part # 100860
The Nimbus TDS-2B TDS Monitor is designed to operate within the Remote Bypass Unit of the
Nimbus MN system. It is installed inside the upper left corner of the Bypass Unit frame and is
connected to a tee fitting installed in the product water output line. The Monitor is powered by a
9V battery accessible via a sliding cover at the rear of the case. When the red front panel push-
button switch is pressed, the probe mounted in the product water line senses the TDS level in the
water flow. The monitor will then act to illuminate the green LED indicator if the product water
TDS is below the preset level or the red LED if the product water TDS exceeds the preset level.
The monitor is turned off when the push-button is released.
Specifications
Preset Level Selection*
(default 100 ppm)
50/75/100/150/200/250/300/500 ppm
Power Supply
Sensing Method
Actuation
9V DC
AC signal conductivity
Push-button switch
*Not temp compensated – levels calibrated to 25°C/77°F
Preset Level Adjustment
The TDS Monitor is preset to 100 ppm. To change the preset level, remove the small screw at
the center of the rear cover. Carefully remove the rear cover assembly. On the circuit board
inside the rear cover locate the 8-position selector switch. The switches marked 1 through 8
determine the preset level. With a ballpoint pen or small screwdriver place the number 3 switch in
the “OFF” position, then place the new TDS level switch in the “ON” position (top end depressed).
The corresponding TDS preset for each switch is as follows 1=50, 2=75, 3=100, 4=150, 5=200,
6=250, 7=300, 8=500. Only one of the eight switches should be in the “ON” position. When
finished, re-install the assembly in reverse order.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
§9.3 WARRANTY
Nimbus Water Systems
Limited One Year Warranty
Commercial and Industrial Systems
The Nimbus Water Systems (Nimbus) Limited Warranty extends to the original purchaser of the system. This warranty covers all parts
and factory labor needed to repair any Nimbus-supplied item that proves to be defective material, workmanship or factory preparation.
The above-mentioned warranty applies for the first full calendar year from the date of purchase. These defective items are subject to the
following exclusions: membranes, filters, O-rings, and all other parts or components that require regular replacement as a result of
ordinary usage.
Disclaimers This Warranty applies only if the system is installed and used in compliance with the instructions enclosed in the system.
The Warranty does not cover any non-Nimbus parts. This Warranty does not cover the costs of repairs or adjustments to the unit that
may be needed because of the use of improper parts, equipment or materials. This Warranty does not cover repairs required due to use
of non-Nimbus parts, unauthorized alterations of the unit, failure of a unit caused by such alterations or by unauthorized repairs.
The Warranty does not cover malfunctions of the unit due to tampering, misuse, alteration, lack of regular maintenance, misapplication,
fouling due to hydrogen sulfide or iron, scaling from excessive hardness, or excessive membrane hydrolysis due to chlorine levels in
excess of 1.0 mg/L, or operating at too high a recovery. In addition, damage to the unit due to fire, accident, negligence, act of god, or
events beyond the control of Nimbus are not covered by this warranty.
Nimbus warrants the membranes per the manufacturers warranty. These warranties generally cover faulty material and workmanship
for anywhere from one to three years. Membrane fouling is not covered.
Nimbus warrants all items supplied by outside vendors, that are used are part of the system provided, per the manufacturers warranties.
These warranties generally cover faulty material and workmanship for one year.
Incidental and Consequential Damages Nimbus does not assume responsibility for payment of incidental damages as a result of the
failure of this unit to comply with express or implied warranties, such as lost time, inconvenience, damage to personal property, loss of
revenue, commercial losses, postage, travel, telephone expenditures, or other losses of this nature. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so this exclusion may not apply to you.
Owner’s Warranty Responsibilities Under the provisions of this Warranty, the owner is expected to perform timely maintenance, as
described in this Manual. Neglect, improper maintenance, abuse, or unapproved modifications may invalidate the Warranty. Should
your unit develop a defect or otherwise fail to perform in accordance with this warranty, you should contact the Nimbus dealer from
whom the product was originally purchased.
Implied Warranties Implied at-law warranties of merchantability and fitness for a particular purpose shall terminate on the date one year
after the date of purchase. Note: some states do not allow limitations on how an implied warranty lasts, so the above limitations may not
apply to you.
Other Rights This Warranty gives you specific legal rights and you may also have other rights that vary from state to state.
Returned Goods Authorization In order to process a return, a Returned Goods Authorization (RGA) number will be assigned. Include
the RGA number with an explanation of the defect with the item being returned. Items returned under the RGA process will be reviewed
by Nimbus and/or forwarded to the original manufacturer for evaluation. Items returned to Nimbus must be sent prepaid.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
|