6. On the Admin Password page,
change the system login
password, and provide a
recovery question, answer, and
email address. Note these
changes. Click Next to
proceed.
Use the Setup Wizard to Configure Basic Settings
)NSTALLATION 'UIDE
The Setup Wizard will guide you through setting up basic file sharing. Refer to the
ReadyNAS Pro User Manual for instructions on configuring options like backup,
streaming media servers, printers, VLAN, or user accounts and quotas.
NETGEAR® ReadyNAS™ Pro
Note: If you choose to bypass the Setup Wizard, be sure to configure and alerts email
address, change the admin password, and provide a password recovery question.
Follow these instructions to install your NETGEAR® ReadyNAS™ Pro. Then, consult
the ReadyNAS Pro User Manual for instructions on configuring and operating your unit.
A link to the ReadyNAS Pro User Manual is on the Installation CD and on the NETGEAR
factory default X-RAID2 disk configuration.
7. On the Security Mode tab
1. In the factory default state,
when logged in to the unit,
Setup Wizard is enabled. Click
Next to proceed with the
wizard.
page, accept the default option
of “User” which controls
access to shares based on user
or group accounts. FrontView
will attempt to use the first workgroup name it discovers in the network. Otherwise, it
will default to “VOLUME” as the workgroup name. Specify the workgroup name you
want the unit to join. Refer to the ReadyNAS Pro User Manual for ACS setup
instructions. Click Next to proceed.
Estimated completion time: 20 minutes.
Note: A diskless unit requires installing disks and initializing RAID before proceeding.
User Manual for instructions on installing disks and configuring RAID.
2. On the Clock tab page, modify
or accept the default timezone,
time, and NTP options. Click
Next to proceed.
First, Install the RAIDar Utility
8. On the Accounts page, click Add User. Add a new user and user password. Click
Next to finish the wizard. Refer to the ReadyNAS Pro User Manual for full
instructions on setting up accounts.
3. On the Alerts tab page, provide
at least one email address for
system alerts. Click Next to
proceed.
Install the RAIDar utility from the product Installation CD. Windows, MAC and Linux
versions of the RAIDar utility are provided.
This completes the basic setup. Next, you will verify that you can access shares on your
ReadyNAS Pro.
Next, Connect the Unit
4. On the Ethernet 1 tab page,
accept or change the IP address
settings.
For initial setup, connect one Ethernet port of the ReadyNAS Pro to your network, and
turn it on. It takes about a minute to boot. The factory default is to get its IP address via
DHCP. After it boots, the status area will display the IP address assigned to the unit and
the amount of disk space available. Note the IP address displayed in the status area.
Accessing Your Shared Storage
Click Next to proceed.
Follow the steps below to access shares on the ReadyNAS Pro.
5. On the Global Settings tab
page, you can modify the unit’s
hostname. Also, if you will use
a static IP configuration, you
will need to configure the
Note that, by default, these file sharing protocols are enabled: CIFS, AFP (advertised over
both Bonjour and ATP), HTTP/S. FTP, NFS, and Rsync are supported but are not enabled
by default.
Log in to the Unit
Refer to the ReadyNAS Pro User Manual for instructions on accessing shares from Linux
or Unix workstations, drive mapping, and other file sharing options, including unique
language support for file names such as those that use unicode or ideographic characters.
1. Run the RAIDar utility. It will detect the unit.
gateway and DNS settings (you
do not have to change these
settings if you use the unit in its
default DHCP configuration).
Click Next to proceed.
Tip: In your DHCP server, reserve the IP address assigned for your ReadyNAS Pro so that
it always gets this address. This helps assure that mapped drives work consistently on
any operating system.
Accessing Shares from a Windows PC
2. Click Setup to open a browser ReadyNAS Pro FrontView session
with the unit. The login screen will display. The default user name
is admin and the password is netgear1.
1. To see a share listing in Windows, either click Browse in RAIDar or enter
\\<ip_address> or \\<hostname> in the Windows Explorer address bar.
\\Nv6-07-15-F4
The FrontView configuration utility home page displays.
Download from Www.Somanuals.com. All Manuals Search And Download.
|