NEC Flat Panel Television Enhanced split screen Model User Manual
Operation Manual  
(Enhanced split screen Model)  
For the specifications of your plasma monitor,  
refer to “Model Information”.  
NEC Solutions (America), Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
your investment in this plasma monitor, please adhere to the  
following guidelines and recommendations for minimizing  
the occurrence of image burn:  
* Lower the Brightness and Contrast levels as much as  
possible without impairing image readability.  
* Display an image with many colors and color gradations  
(i.e. photographic or photo-realistic images).  
* Always enable and use your computer’s screen saver  
function during use with a computer input source.  
* Display a moving image whenever possible.  
* Change the position of the menu display from time to time.  
* Always power down the monitor when you are finished  
using it.  
* Create image content with minimal contrast between light  
and dark areas, for example white characters on black  
backgrounds. Use complementary or pastel color whenever  
possible.  
* Avoid displaying images with few colors and distinct,  
sharply defined borders between colors.  
If the plasma monitor is in long term use or continuous  
operation take the following measures to reduce the  
likelihood of phosphor burn:  
* Note:Burn-in is not covered by the warranty.  
Contact your dealer for other recommended procedures that  
will best suit your particular application needs.  
Recommandations importantes  
Précautions  
Mises en garde et précautions de  
Veuillez lire avec attention ce manuel avant d’utiliser le  
moniteur à plasma et le conserver accessible pour s’y référer  
ultérieurement.  
sécurité  
Ce moniteur à plasma a été conçu et fabriqué pour  
une utilisation fiable et durable. Il ne nécessite aucun  
entretien en dehors du nettoyage. Voir la section  
“Méthode de nettoyage du moniteur àplasma”plus loin.  
Le panneau à affichage plasma est constitué de fines  
particules d’images (cellules) dont plus de 99,99%sont  
actives. Certaines d’entre elles ne produisent pas de  
lumière ou restent allumées.  
ATTENTION  
RISQUE D’ELECTROCUTION  
NE PAS OUVRIR  
Pour des raisons de sécurité et pour éviter  
d’endommager l’appareil, lire attentivement les  
instructions suivantes.  
MISE EN GARDE: AFIN DE REDUIRE LES RISQUES  
D’ELECTRO-CUTION, NE PAS  
DEPOSER LE COUVERCLE, IL N’Y A  
AUCUNE PIECE UTILISABLE A  
L’INTERIEUR DE CET APPAREIL. NE  
CONFIER LES TRAVAUX D’ENTRETIEN  
QU’A UN PERSONNEL QUALIFIE.  
Pour éviter les risques d’éléctrocution et d’incendie:  
1. Laisser suffisament d’espace autour de l’appareil pour  
la ventilation et éviter toute augmentation excessive de  
la température interne. Ne pas couvrir les évents ou  
l’installer dans un endroit trop exigu.  
Ce symbole a pour but de prévenir l’utilisateur  
de la présence d’une tension dangereuse, non  
isolée se trouvant à l’intérieur de l’appareil.  
Elle est d’une intensité suffisante pour  
constituer un risque d’électrocution. Eviter le  
contact avec les pièces à l’intérieur de cet  
appareil.  
Si vous installez l’appareil dans un espace clos,  
assurezvous qu’il y ait suffisamment d’espace au dessus  
pour permettre à l’air chaud de s’élever et de s’évacuer.  
Si la température du moniteur devient excessive, la  
protection contre les surchauffes entrera en action et  
coupera l’alimentation. Dans ce cas, éteindre l’appareil  
et débrancher le câble d’alimentation. Si la température  
de la pièce dans laquelle se trouve le moniteur est  
particulièrement élevée, déplacer celui-ci dans un endroit  
plus frais et attendre environ 60 minutes qu’il refroidisse.  
Si le problème persiste, prendre contact avec votre  
revendeur.  
Ce symbole a pour but de prévenir l’utilisateur  
de la présence d’importantes instructions  
concernant l’entretien et le fonctionnement de  
cet appareil. Par conséquent, elles doivent être  
lues attentivement afin d’éviter des problèmes.  
2. Ne pas raccorder la prise d’alimentation polarisée de ce  
périphérique à une rallonge ou une prise murale si les  
fiches ne peuvent pas être complètement insérées.  
3. Ne pas exposer à L’eau ou à l’humidité.  
4. Eviter d’endommager le cordon d’alimentation, et ne pas  
modifier le cordon d’alimentation.  
AVERTISSEMENT  
AFIN DE REDUIRE LES RISQUES D’INCENDIE OU  
D’ELECTROCUTION, NE PAS EXPOSER CETAPPAREIL  
ALAPLUIE OUAL’HUMIDITE.AUSSI, NE PAS UTILISER  
LA FICHE POLARISEE AVEC UN PROLONGATEUR OU  
UNEAUTRE PRISE DE COURANT SAUF SI CES LAMES  
PEUVENT ETRE INSEREES A FOND. NE PAS OUVRIR  
LE COFFRET, DES COMPOSANTS HAUTETENSION SE  
TROUVENTAL’INTERIEUR. LAISSERAUN PERSONNEL  
5. Débrancher le câble d’alimentation électrique pendant les  
orages ou les longues périodes d’inactivité.  
6. Ne pas ouvrir le coffret. Des composants de haute  
tension se trouvent à l’intérieur. Si l’appareil est  
endommagé de cette manière, la garantie devient  
caduque. De plus, il y a risque d’électrocution.  
7. Ne pas essayer d’intervenir ou de réparer l’appareil. Le  
QUALIFIE LE SOIN DE REPARER CET APPAREIL.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
fabricant décline toute responsabilité en cas de blessure  
corporelle ou de dégâts matériels résultant d’une opération  
d’entretien quelconque effectuée par des personnes non  
qualifiées ou résultant de l’ouverture du couvercle arrière.  
S’adresser aux services après-vente autorisés.  
• Assurez-vous de mettre en marche et d’utliser  
l’économisateur d’écran chaque fois que c’est possible  
lorsque vous l’utilisez avec une source d’entrée  
d’ordinateur.  
• Affichez une image en mouvement aussi souvent que  
possible.  
Pour éviter des dommages et prolonger la durée de  
service de l’appareil:  
• Changer la position de l’affichage de menu de temps àautre.  
• Coupez toujours l’alimentation lorsque vous avez terminé  
d’utiliser la moniteur.  
1. N’utiliser qu’une source d’alimentation de 100-240 V  
50/60 Hz CA. Le fait d’utiliser l’appareil en continu à  
des tensions de ligne supérieures à 100-240 Volts CA  
réduit sa durée de vie et risque de provoquer un incendie.  
2. Manipuler l’appareil avec soin pendant son  
déplacement et ne pas le faire tomber.  
Si le moniteur est en usage continu ou longue durée, prenez  
les mesures suivantes afin d’éviter l’occurence le brûlage  
du luminophore:  
3. Eloigner l’appareil des endroits chauds, très poussiéreux  
et exposés en plein soleil.  
• Abaissez le niveau de l’image (contraste, luminosité)  
autant que possible, sans faire perdre la lisibilité de  
l’image.  
• Affichez une image avec de nombreuses couleurs et  
graduations de couleur (par ex. des images  
photographiques ou photo-réalistes).  
• Créez un contenu d’image avec un contraste minimal  
entre les zones sombres et les zones claires, par exemple,  
des caractères blancs sur un fond noir. Utilisez des  
couleurs complémentaires ou pastels le plus souvent  
possible.  
4. Eviter que des liquides et des petits objets métalliques  
pénètrent à l’intérieur de l’appareil. En cas d’incident de  
ce genre, débrancher le câble d’alimentation électrique  
et confier le moniteur à un service après-vente agréé.  
5. Ne pas frapper ou rayer la surface de la écran plasma,  
car des défauts risquent de se produire sur la surface  
de la écran plasma.  
6. Pour un montage et une installation correcte, il est  
fortement recommandé de faire appel à un revendeur  
agréé et qualifié.  
• Évitez d’afficher des images avec peu de couleurs et des  
limites nettes et clairement définies entre les couleurs.  
7. Comme c’est le cas pour tout affichage à base de  
phosphore (comme un moniteur CRT, par exemple), la  
puissance de lumière baisse graduellement au cours de  
la vie du Panneau d’Affichage à Plasma.  
* Remarque:Le brûlage de l’écran n’est pas couvert  
par la garantie.  
8. Pour éviter tout risque de sulfuration, il est fortement  
conseillé de ne pas installer l’appareil dans un vestiaire,  
un bain public ou un bain de source thermale.  
9. Ne pas utiliser dans un véhicule en marche car l’unité  
pourrait tomber ou glisser et provoquer des blessures.  
10. Pour éviter l ‘inflammation ou les chocs électriques, ne  
pas placer l’unité sur la tranche, à l’envers ou avec l’écran  
vers le bas ou vers le haut.  
Contactez un revendeur agréé ou un revendeur de marque  
pour d'autres procédures qui conviendront le mieux à vos  
besoins particuliers.  
Méthode de nettoyage du moniteur à plasma:  
1. Nettoyer le panneau avant et le cadre en procédant àl’aide  
d’un chiffon doux et sec. Ne jamais utiliser de solvents  
du type alcool ou diluant pour le nettoyage de ces surfaces.  
2. Nettoyer les prises d’aération du plasma en procédant à  
l’aide d’une brosse à poils doux fixée à un aspirateur.  
3. Pour garantir la bonne ventilation du moniteur, nettoyer  
les prises d’air tous les mois. Un nettoyage plus fréquent  
peut s’avérer nécessaire selon les conditions  
environnantes dans lesquelles le moniteur à plasma est  
utilisé.  
Pour éviter les risques de brûlage du luminophore, les  
mesures suivantes sont recommandées:  
Comme tous les périphériques d’affichage àbase luminophore  
et tous les autres affichages gaz plasma, les moniteurs plasma  
peuvent être sujets au brûlage du luminophore dans certaines  
circonstances. Certaines conditions d’utilisation, telles que  
l’affichage continu d’une image statique pour une durée  
prolongée, peuvent causer le brûlage du luminophore si  
aucune précaution n’est prise. Pour protéger votre  
investissement dans ce moniteur à plasma, veuillez suivre  
les directives et les conseils suivantes pour minimiser  
l’occurence le marquage de l’écran:  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Setting the background color when no signal is being  
input ........................................................................ 24  
Setting the gray level for the sides of the screen ......... 25  
Setting the screen size for S1/S2 video input .............. 25  
Turning on/off the menu display ................................ 25  
Setting the position of the menu ................................. 25  
Resetting to the default values.................................... 25  
Function Settings Menu ........................................... 26  
Setting the power management for computer images ..... 26  
POWER/STANDBY indicator ................................... 26  
Setting the Input Skip................................................. 26  
Erasing the sub screen image when there is no input  
signal ....................................................................... 26  
Displaying the entire image during DIGITAL ZOOM  
operations ................................................................ 27  
Displaying still images in the sub screen .................... 27  
Reducing burn-in of the screen .................................. 27  
Setting Closed Caption .............................................. 29  
Reducing the brightness of Closed Caption ................ 29  
Signal Information Menu......................................... 29  
Checking the frequencies, polarities of input signals,  
and resolution .......................................................... 29  
Installation ...................................................... 6  
Ventilation Requirements for enclosure mounting .......... 6  
How to use the safety metal fittings and the screws for  
safety metal fittings................................................ 6  
Cable Management.................................................. 7  
How to use the remote control.................................... 7  
Battery Installation and Replacement ........................... 7  
Operating Range .......................................................... 7  
Handling the remote control......................................... 7  
Part Names and Function .................................. 8  
Front View .............................................................. 8  
Rear View/ Terminal Board ....................................... 9  
Remote Control ...................................................... 10  
Basic Operations............................................. 11  
POWER ................................................................ 11  
To turn the unit ON and OFF: .................................... 11  
VOLUME .............................................................. 11  
To adjust the sound volume:....................................... 11  
MUTE ................................................................... 11  
To mute the audio: ..................................................... 11  
DISPLAY ................................................................ 11  
To check the settings: ................................................. 11  
DIGITAL ZOOM ..................................................... 11  
OFF TIMER ............................................................ 11  
To set the off timer: .................................................... 11  
To check the remaining time: ..................................... 11  
To cancel the off timer: .............................................. 11  
External Control ............................................. 30  
Application ........................................................... 30  
Connections .......................................................... 30  
Type of connector: D-Sub 9-pin male ........................ 30  
Communication Parameters ..................................... 30  
External Control Codes (Reference) .......................... 30  
WIDE Operations............................................. 12  
Wide Screen Operation (manual) ............................ 12  
When viewing videos or digital video discs ............... 12  
Wide Screen Operation with Computer Signals ......... 13  
Pin Assignments ............................................. 30  
mini D-Sub 15-pin connector (Analog) ..................... 30  
DVI-D 24-pin connector (Digital) .............................. 30  
Troubleshooting.............................................. 31  
SPLIT SCREEN Operations ................................. 14  
Showing a couple of pictures on the screen at the  
same time .......................................................... 14  
Operations in the Side-by-side mode.......................... 14  
Operations in the Picture-in-picture mode .................. 15  
Selecting the input signals to be displayed ................. 15  
Zooming up pictures .................................................. 15  
Adjusting the OSM controls....................................... 15  
Contents of the Package  
Ⅺ Plasma monitor  
Ⅺ Power cord  
Ⅺ Remote control with two AAA Batteries  
Ⅺ Manuals (Model Information and Operation)  
Ⅺ Safety metal fittings*  
OSM (On Screen Menu) Controls ....................... 16  
Menu Operations ................................................... 16  
Menu Tree ............................................................. 17  
Picture Settings Menu.............................................. 19  
Storing picture settings............................................... 19  
Adjusting the picture .................................................. 19  
Reducing noise in the picture ..................................... 19  
Setting the color temperature ..................................... 20  
Adjusting the color to the desired level ...................... 20  
Changing the Gamma Curve ...................................... 20  
Making the Low Tone adjustments ............................ 20  
Adjusting the pedestal level (black level) ................... 21  
Adjusting the colors ................................................... 21  
Setting the picture to suit the movie ........................... 21  
Setting the picture mode according to the brightness of  
the room .................................................................. 21  
Audio Settings Menu .............................................. 22  
Adjusting the treble, bass and left/right balance and  
Ⅺ Ferrite cores, bands  
Ⅺ Cable clamps  
Ⅺ HDMI-DVI cable  
* Contents will differ according to the model.  
* These are fittings for fastening the unit to a wall to prevent  
tipping due to external shock when using the stand  
(optional). Fasten the safety fittings to the holes in the  
back of the monitor using the safety fitting mount screws  
(see page 6).  
audio input select..................................................... 22  
Setting the allocation of the audio connectors ............ 22  
Image Adjust Settings Menu .................................... 22  
Adjusting the Position, Size, Fine Picture, Picture Adj ..... 22  
SET UP Settings Menu ............................................. 23  
Setting the language for the menus............................. 23  
Setting the BNC connectors ....................................... 23  
Checking the signal being transmitted to RGB1 terminal .... 23  
Setting high definition images to the suitable screen size .... 23  
Setting a computer image to the correct RGB select  
Options  
• Wall mount unit  
• Ceiling mount unit  
• Tilt mount unit  
• Stand  
• Attachable speakers  
screen ...................................................................... 23  
Setting the signal and black level for DVI signal ........ 24  
Setting the video signal format ................................... 24  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
You can attach your optional mounts or stand to the plasma monitor in one of the following two ways:  
* While it is upright. (See Drawing A)  
* As it is laid down with the screen face down (See Drawing B). Lay the protective sheet, which was wrapped around the  
monitor when it was packaged, beneath the screen surface so as not to scratch the screen face.  
* Do not touch or hold the screen face when carrying the unit.  
• This device cannot be installed on its own. Be sure to use a stand or original mounting unit. (Wall  
mount unit, Stand, etc.)  
* See page 5.  
• For correct installation and mounting it is strongly recommended to use a trained, authorized  
dealer.  
Failure to follow correct mounting procedures could result in damage to the equipment or injury  
to the installer.  
Product warranty does not cover damage caused by improper installation.  
* Use only the mounting kit or stand provided by manufacturer and listed under Options.  
Drawing A  
Drawing B  
When installing or carrying, use the  
handles attached to the upper back  
of the display.  
Ventilation Requirements for  
enclosure mounting  
To allow heat to disperse, leave space between surrounding  
objects as shown on the diagram below when installing.  
How to use the safety metal fittings  
and the screws for safety metal  
fittings  
These are fittings for fastening the unit to a wall to prevent  
tipping due to external shock when using the stand  
(optional). Fasten the safety fittings to the holes in the  
back of the monitor using the safety fitting mount screws.  
* Safety metal fittings will differ according to the model.  
Wall  
50mm (2")  
50mm (2")  
Screw hole  
Wall  
Screw or Hook etc.  
(Not supplied)  
Safty metal fittings  
Screw for Safty metal  
50mm (2")  
Wall  
fittings  
Metal chain  
(Not supplied)  
Table Top  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operating Range  
Cable Management  
Using the cable clamps provided with the plasma display,  
bundle at the back of the unit the signal and audio cables  
connected to the display.  
* Use the remote control within a distance of about 7 m/  
23ft. from the front of the monitor’s remote control sensor  
and at horizontal and vertical angles of up to approximately  
30°.  
* The remote control operation may not function if the  
monitor’s remote control sensor is exposed to direct  
sunlight or strong artificial light, or if there is an obstacle  
between the sensor and the remote control.  
Back of the unit  
mounting holes  
To attach  
Approx.  
7m/23ft  
1.  
2.  
clamp  
cables  
mounting hole  
To detach  
Handling the remote control  
• Do not drop or mishandle the remote control.  
• Do not get the remote control wet. If the remote control  
gets wet, wipe it dry immediately.  
• Avoid heat and humidity.  
• When not using the remote control for a long period,  
remove the batteries.  
• Do not use new and old batteries together, or use different  
types together.  
How to use the remote control  
Battery Installation and Replacement  
Insert the 2 “AAA” batteries, making sure to set them in  
with the proper polarity.  
• Do not take apart the batteries, heat them, or throw them  
into a fire.  
1.Press and open the cover.  
2.Align the batteries according to the (+) and (–) indication  
inside the case.  
3.Replace the cover.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Part Names and Function  
Front View  
VOLUME  
DOWN  
INPUTSELECT  
EXIT  
MENU/ENTER  
UP  
LEFT/  
-
RIGHT/  
+
/
VOLUME  
DOWN  
INPUTSELECT  
/EXIT  
-
+
MENU/ENTER  
UP  
LEFT/  
RIGHT/  
6
5
4
1
3
2
7
q Power  
t LEFT/– and RIGHT/+  
Enlarges or reduces the image. Functions as the  
Turns the monitor’s power on and off.  
ᮤ
ᮣ
CURSOR (  
(OSM) mode.  
/
) buttons in the On-Screen Menu  
w Remote sensor window  
Receives the signals from the remote control.  
y VOLUME DOWN and UP  
e POWER/STANDBY indicator  
Adjusts the volume. Functions as the CURSOR (▲/  
▲) buttons in the On-Screen Menu (OSM) mode.  
When the power is on ............................. Lights green.  
When the power is in the standby mode ... Lights red.  
u MENU/ENTER  
r INPUT SELECT / EXIT  
Sets the On-Screen Menu (OSM) mode and displays  
the main menu.  
Switches the input.  
The available inputs depend on the setting of “BNC  
INPUT”, “RGB SELECT” and “DVI SET UP”.  
Functions as the EXIT buttons in the On-Screen Menu  
(OSM) mode.  
WARNING  
The Power on/off switch does not disconnect the plasma  
display completely from the supply mains.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Rear View/ Terminal Board  
C
D
E
F
G
H
A B  
I
A AC IN  
F DVD2/ HD2, RGB2  
Connect the included power cord here.  
DVD2/ HD2: You can connect DVDs, High  
Definition sources, Laser Discs, etc.  
here.  
B EXT SPEAKER L and R  
Connect speakers (optional) here. Maintain the correct  
This input can be set for use with an  
RGB or component source. (see page  
23)  
polarity. Connect the  
EXT SPEAKER terminal and the  
speaker wire to the EXT SPEAKER terminal on  
(positive) speaker wire to the  
(negative)  
RGB2:  
You can connect an analog RGB signal  
and the syncronization signal.  
both LEFT and RIGHT channels.  
Please refer to your speaker’s owner’s manual.  
G RGB1 (D-Sub)  
C VIDEO1, 2, 3 (BNC, RCA, S-Video)  
Connect an analog RGB signal from a computer, etc.  
here.  
Connect VCR’s, DVD’s or Video Cameras, etc. here.  
D AUDIO1, AUDIO2, AUDIO3  
H DVD3/ HD3, RGB3 (DVI)  
These are audio input terminals.  
The input is selectable. Set which video image to allot  
them from the audio menu screen.  
Connect a digital signal (TMDS) from a source with a  
DVI output.  
This input can be set for use with an RGB3 or DVD3/  
HD3 source. (see page 24)  
E DVD1 / HD1  
Connect DVD’s, High Definition or Laser Discs, etc.  
here.  
I
EXTERNAL CONTROL (D-Sub)  
This terminal is used when operating and controlling  
the monitor externally (by external control).  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
i MUTE  
Mutes the audio.  
Remote Control  
o VOLUME (+ /–)  
Adjusts the audio volume.  
! ZOOM (+ /–)  
Enlarges or reduces the image.  
! SINGLE  
Cancels the split screen mode.  
! SIDE BY SIDE  
Press this button to show a couple of pictures in the  
side-by-side mode.  
! PICTURE IN PICTURE  
Press this button to show a couple of pictures in the  
picture-in-picture mode.  
! ACTIVE SELECT  
Press this button to make the desired picture activate  
during split screen mode.  
! VIDEO1, 2, 3  
Press this button to select VIDEO as the source.  
VIDEO can also be selected using the INPUT SELECT  
button on the monitor.  
! DVD/HD1, 2, 3  
Press this button to select DVD/HD as the source.  
DVD/HD can also be selected using the INPUT  
SELECT button on the monitor.  
! PC/RGB  
Press this button to select PC/RGB as the source.  
PC/RGB can also be selected using the INPUT  
SELECT button on the monitor.  
! PICTURE MEMORY  
Switches sequentially between picture memory settings  
1 to 6.  
! Remote control signal transmitter  
Transmits the remote control signals.  
q POWER ON/STANDBY  
Switches the power on/standby.  
(This does not operate when POWER/STANDBY  
indicator of the main unit is off.)  
w OFF TIMER  
Activates the off timer for the unit.  
e DISPLAY  
Displays the source settings on the screen.  
r WIDE  
Automatically detects the signal and sets the aspect  
ratio.  
Wide button is not active for all signals.  
t MENU/ENTER  
Press this button to access the OSM controls.  
Press this button during the display of the main menu  
to go to the sub menu.  
ᮤ
ᮣ
y CURSOR (▲ / ▲ /  
/
)
Use these buttons to select items or settings and to  
adjust settings or switch the display patterns.  
u EXIT  
Press this button to exit the OSM controls in the main  
menu. Press this button during the display of the sub  
menu to return to the previous menu.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Basic Operations  
POWER  
OFF TIMER  
To turn the unit ON and OFF:  
1. Plug the power cord into an active AC power outlet.  
2. Press the Power button (on the unit).  
The monitor’s POWER/STANDBY indicator turns red  
and the standby mode is set.  
To set the off timer:  
The off timer can be set to turn the power off after 30, 60,  
90 or 120 minutes.  
1. Press the OFF TIMER button to start the timer at 30  
minutes.  
2. Press the OFF TIMER button to the desired time.  
3. The timer starts when the menu turns off.  
→ 30 → 60 → 90 → 120 → 0  
3. Press the POWER ON button (on the remote control) to  
turn on the unit.  
The monitor’s POWER/STANDBY indicator will light  
up (green) when the unit is on.  
4. Press the POWER STANDBY button (on the remote  
control) or the Power button (on the unit) to turn off the  
unit.  
OFF TIMER 30  
The monitor’s POWER/STANDBY indicator turns red  
and the standby mode is set (only when turning off the  
unit with the remote control).  
VOLUME  
To adjust the sound volume:  
To check the remaining time:  
1. Once the off timer has been set, press the OFF TIMER  
button once.  
1. Press and hold the VOLUME  
button (on the remote  
control or the unit) to increase to the desired level.  
2. Press and hold the VOLUME  
button (on the remote  
2. The remaining time is displayed, then turns off after a few  
seconds.  
control or the unit) to decrease to the desired level.  
3. When five minutes remain the remaining time appears  
until it reaches zero.  
MUTE  
To mute the audio:  
Press the MUTE button on the remote control to mute the  
OFF TIMER 28  
audio; press again to restore.  
DISPLAY  
To check the settings:  
1. The screen changes each time the DISPLAY button is  
pressed.  
2. If the button is not pressed for approximately three seconds,  
the menu turns off.  
To cancel the off timer:  
1. Press the OFF TIMER button twice in a row.  
2. The off timer is canceled.  
DIGITAL ZOOM  
Digital zoom specifies the picture position and enlarges  
the picture.  
OFF TIMER  
0
1. (Be sure ZOOM NAV is off.)  
Press the ZOOM (+ or -) button to display magnifying  
glass. (  
)
To change the size of the picture:  
Press the ZOOM+ button and enlarge the picture.  
A press of the ZOOM- button will reduce the picture  
and return it to its original size.  
Note:  
To change the picture position:  
After the power is turned off with the off timer ...  
ᮤ ᮣ  
Select the position with the LL  
buttons.  
A slight current is still supplied to the monitor. When you  
are leaving the room or do not plan to use the system for a  
long period of time, turn off the power of the monitor.  
2. Press the EXIT button to delete the pointer.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WIDE Operations  
The picture is expanded in the horizontal and vertical  
direction, maintaining the original proportions.  
* Use this for theater size (wide) movies, etc.  
Wide Screen Operation (manual)  
With this function, you can select one of six screen sizes.  
When viewing videos or digital video discs  
1. Press the WIDE button on the remote control.  
2. Within 3 seconds ...  
2.35:1 size screen  
Press the WIDE button again.  
The screen size switches as follows:  
Ł
→ NORMAL → ANAMORPHIC → STADIUM → ZOOM → 2.35:1 → 14:9  
Original image  
Information is lost on both sides.  
When a 720P or 1080I signal is input:  
The squeezed film image is expanded to fulfill the entire  
screen at a ratio of 2.35:1. Black bands do not appear at  
the top and bottom but information is lost on the left and  
right margins.  
ANAMORPHIC ↔ 2.35:1  
When displaying enhanced split screen:  
NORMAL ↔ ANAMORPHIC  
• This feature is available when the input signal is video,  
component (480I, 480P, 576I, 576P, 720P, 1080I) or RGB  
(525P or 625P signal from a scan converter).  
* If black bands appear on the top and bottom in the full size  
screen, select the 2.35:1 size screen to avoid phosphor burn-  
in.  
NORMAL size screen (4:3)  
14:9 size screen  
The normal size screen is displayed.  
* The picture has the same size as video pictures with a 4 : 3  
aspect ratio.  
ANAMORPHIC size screen  
The image is displayed at a 14:9 aspect ratio.  
* This feature is available when the input signal is video,  
component (480I, 480P, 576I, 576P) or RGB (525Por 625P  
signal from a scan converter).  
Note:  
The image is expanded in the horizontal direction.  
* Images compressed in the horizontal direction (“squeezed  
images”) are expanded in the horizontal direction and  
displayed on the entire screen with correct linearity.  
(Normal images are expanded in the horizontal direction.)  
Do not allow the displayed in 4:3 mode for an extended  
period. This can cause a phosphor burn-in.  
STADIUM size screen  
The picture is expanded in the horizontal and vertical  
directions at different ratios.  
* Use this for watching normal video programs (4:3) with a  
wide screen.  
ZOOM size screen  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Wide Screen Operation with  
Computer Signals  
Switch to the wide screen mode to expand the 4 : 3 image  
to fill the entire screen.  
Information  
Ⅵ Supported resolution  
See page 7 of Model Information for details on the  
display output of the various VESA signal standards  
supported by the monitor.  
1.Press the WIDE button on the remote control.  
Ⅵ When 852 (848) dot 
ן
 480 line wide VGA*  
signals with a vertical frequency of 60 Hz and  
horizontal frequency of 31.7 (31.0) kHz are in-  
put  
2.Within 3 seconds ...  
Press the WIDE button again.  
The screen size switches as follows:  
→ NORMAL → ANAMORPHIC → ZOOM  
Select an appropriate setting for RGB SELECT mode  
referring to the“Table of Signals Supported” on page 7  
of Model Information.  
When displaying enhanced split screen:  
NORMAL ↔ ANAMORPHIC  
* “VGA”, “SVGA” and “SXGA” are registered  
trademarks of IBM, Inc. of the United States.  
NORMAL size screen (4:3 or SXGA 5:4)  
Note:  
Do not allow the displayed in 4:3 mode for an extended  
period. This can cause a phosphor burn-in.  
The picture has the same size as the normal computer  
image.  
ANAMORPHIC size screen  
The image is expanded in the horizontal direction.  
ZOOM size screen  
When wide signals are input.  
ANAMORPHIC size screen  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPLIT SCREEN Operations  
Operations in the Side-by-side mode  
Showing a couple of pictures on the  
ᮤ ᮣ  
ᮢ
screen at the same time  
To change the picture size, press the cursor  
button.  
or  
* An RGB-input picture may not be displayed in these modes,  
depending on the input signal specifications.  
ᮤ
ᮤ
button  
button  
VIDEO1  
RGB/PC2  
VIDEO1  
RGB/PC2  
VIDEO1  
RGB/PC2  
B
1. Press the button to select a screen mode from among single  
mode, side-by-side, and picture-in-picture.  
A
A
B
B
A
ᮣ
ᮣ
button  
button  
Side-by-Side2-R  
Side-by-Side1  
Side-by-Side2-L  
VIDEO1  
ᮢ
ᮢ
ᮢ
ᮢ
ᮢ
ᮢ
button  
button  
button  
button  
button  
button  
ᮤ
ᮤ
SINGLE  
button  
A
button  
button  
VIDEO1  
A
RGB/PC2  
VIDEO1  
RGB/PC2  
VIDEO1  
RGB/PC2  
SINGLE  
button  
B
A
B
B
A
ᮣ
ᮣ
PICTURE IN PICTURE  
button  
SIDE BY SIDE  
button  
button  
button  
Side-by-Side4-R  
Side-by-Side3  
Side-by-Side4-L  
To swap the picture on the right and the left, press the  
SIDE BY SIDE  
button  
ꢀ
cursor button.  
VIDEO1  
RGB/PC1  
VIDEO1  
RGB/PC1  
A
B
Main screen  
VIDEO1  
RGB/PC1  
Sub  
screen  
PICTURE IN  
PICTURE  
button  
A
B
Note:  
Picture A and B on the above screen are not always of the  
same height.  
ꢀ
button  
RGB/PC1  
VIDEO1  
Information  
B
A
Split screen operations may not function depending on  
the combination of input signals. In the table below,  
“ࠗ” means Yes, “
ן
” means No.  
Pictures displayed on the right/main screen (Select1)  
To make the desired picture active, press the ACTIVE  
SELECT button.  
VIDEO1  
VIDEO2  
VIDEO3 HD/DVD1 HD/DVD2 RGB/PC1 HD/DVD3  
RGB2  
ࠗ
RGB3  
ࠗ
Pictures  
displayed on  
the left/sub  
screen  
VIDEO1  
VIDEO2  
VIDEO3  
HD/DVD1  
HD/DVD2  
RGB2  
ן
ן
ן
ࠗ
ࠗ
ן
ן
ן
ࠗ
ࠗ
ן
ן
ן
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ן
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
VIDEO1  
RGB/PC1  
ࠗ
ࠗ
(Select2)  
ן
ࠗ
RGB/PC1  
HD/DVD3  
RGB3  
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ࠗ
ן
ࠗ
ࠗ
ן
A
B
Ⅵ Split screen operations may not function  
ACTIVE SELECT  
button  
depending on the type of the RGB signals.  
VIDEO1  
RGB/PC1  
A
B
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Operations in the Picture-in-picture mode  
Selecting the input signals to be displayed  
1. Press the ACTIVE SELECT button to make the desired  
picture active.  
ᮤ
To move the position of the sub screen, press the cursor  
ᮣ
or button.  
2. Press the PC/RGB, VIDEO1, 2, 3, or DVD/HD1, 2, 3  
button to change the selection of the input signal.  
The INPUT SELECT button on the monitor can also be  
used to change the selection.  
ᮣ
button  
RGB/PC2  
V
IDEO1  
RGB/PC2  
VIDEO1  
B
B
ᮤ
button  
Top Right  
Top Left  
Zooming up pictures  
ᮣ
ᮤ
ᮤ
ᮣ
1. Press the ACTIVE SELECT button to make the desired  
picture active.  
2. Use the ZOOM (
؀
 or
؁
) button to enlage the picture.  
For details, see “DIGITAL ZOOM” on page 11.  
button  
button  
button  
button  
ᮤ
button  
VIDEO1  
RGB/PC2  
VIDEO1  
RGB/PC2  
B
B
A
A
ᮣ
button  
Adjusting the OSM controls  
1. Press the ACTIVE SELECT button to make the desired  
picture active.  
2. Press the MENU/ENTER button to display the MAIN  
MENU.  
Bottom Left  
Bottom Right  
ᮢ
To change the size of the sub screen, press the button.  
VIDEO1  
RGB/PC1  
3. Adjust the setting to your preference.  
For details, see “OSM (On Screen Menu) Controls” on  
page 16.  
B
A
VIDEO1  
RGB/PC1  
Note:  
B
A
During enhanced split screen, some functions of OSM  
controls are not available.  
ᮢ button  
VIDEO1  
RGB/PC1  
B
A
ᮢ button  
VIDEO1  
RGB/PC1  
B
A
ᮢ button  
ᮢ button  
To make the desired picture active, press the ACTIVE  
SELECT button.  
VIDEO1  
RGB/PC1  
VIDEO1  
RGB/PC1  
B
B
ACTIVE  
SELECT  
button  
A
A
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSM (On Screen Menu) Controls  
Menu Operations  
The following describes how to use the menus and the  
selected items.  
1. Press the MENU/ENTER button on the remote control to  
display the MAIN MENU.  
MAIN MENU  
SET UP  
FUNCTION  
PICTURE  
AUDIO  
SIGNAL INFO.  
IMAGE ADJ.  
SEL.  
MENU/ENTER OK  
EXIT  
EXIT  
2. Press the cursor buttons LLL on the remote control to  
highlight the menu you wish to enter.  
3. Press the MENU/ENTER button on the remote control to  
select a sub menu or item.  
PICTURE  
:
OFF  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
R
:
:
:
:
:
G
TINT  
NR  
COLOR TEMP.  
GAMMA  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
OFF  
MIDDLE  
2.2  
AUTO  
0%  
:
:
ON  
NORMAL  
SEL.  
ADJ.  
MENU/ENTER OK  
EXIT  
RETURN  
4. Adjust the level or change the setting of the selected item  
ᮤ ᮣ  
by using the cursor buttons  
on the remote control.  
CONTRAST  
10  
5. The adjustments or the settings that are stored in memory.  
The change is stored until you change it again.  
6. Repeat steps 2 – 5 to adjust an additional item, or press  
the EXIT button on the remote control to return to the  
main menu.  
* When adjusting using the bar at the bottom of the screen,  
ᮤ
ᮣ
press the or button within 5 seconds. If not, the current  
setting is set and the previous screen appears.  
Note:The main menu disappears by pressing the EXIT  
button.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Menu Tree  
:Shaded areas indicate the default value.  
ᮤ
ᮣ
מ
←→
ם
: Press the or button to adjust. The default value is at the center.  
Main menu  
Sub menu  
Sub menu 2  
Sub menu 3  
Sub menu 4  
RESET  
REFERENCE  
PICTURE  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
TINT  
NR  
COLOR TEMP.  
WHITE BALANCE  
OFF/MEMORY1-6  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
19  
19  
19  
19  
19  
19  
19  
20  
20  
20  
20  
20  
20  
20  
20  
20  
20  
21  
21  
21  
21  
21  
21  
21  
21  
21  
21  
מ
←→
ם
 0←52→72  
מ
←→
ם
 0←32→64  
מ
←→
ם
 0←16→32  
מ
←→
ם
 0←32→64  
R←→G 0←32→64  
OFF/NR-1/NR-2/NR-3  
LOW/MIDDLE LOW/MIDDLE/HIGH  
GAIN RED  
מ
←→
ם
 0←→70  
מ
←→
ם
 0←→70  
GAIN GREEN  
GAIN BLUE  
BIAS RED  
BIAS GREEN  
BIAS BLUE  
RESET  
מ
←→
ם
 0←→70  
מ
←→
ם
 0←→70  
מ
←→
ם
 0←→70  
מ
←→
ם
 0←→70  
OFF←→ON  
GAMMA  
2.1←2.2←2.3→2.4  
…
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
AUTO←→1← →3  
0%←→3.75%←→7.5%  
RED  
Y←→M 0←→64  
GREEN  
BLUE  
YELLOW  
MAGENTA  
CYAN  
RESET  
ON←→OFF  
C←→Y 0←→64  
M←→C 0←→64  
G←→R 0←→64  
R←→B 0←→64  
B←→G 0←→64  
OFF←→ON  
CINEMA MODE  
PICTURE MODE  
DEFAULT/THEATER1/THEATER2/NORMAL/BRIGHT  
Main menu  
Sub menu  
Sub menu 2 Sub menu 3 Sub menu 4  
RESET  
REFERENCE  
AUDIO  
BASS  
TREBLE  
BALANCE  
AUDIO INPUT1  
AUDIO INPUT2  
AUDIO INPUT3  
מ
←→
ם
 0←13→26  
מ
←→
ם
 0←13→26  
L←→R -22←0→+22  
VIDEO 1-3 / HD/DVD 1-3 / RGB 1-3  
VIDEO 1-3 / HD/DVD 1-3 / RGB 1-3  
VIDEO 1-3 / HD/DVD 1-3 / RGB 1-3  
YES  
YES  
YES  
YES  
YES  
YES  
22  
22  
22  
22  
22  
22  
Main menu  
Sub menu  
Sub menu 2  
Sub menu 3  
Sub menu 4  
RESET  
REFERENCE  
IMAGE ADJUST  
ASPECT MODE  
V-POSITION  
H-POSITION  
V-HEIGHT  
ZOOM/NORMAL/ANAMORPHIC/STADIUM/14:9/2.35:1  
מ
←→
ם
 -64←0→+64  
מ
←→
ם
 -128←0→+127  
מ
←→
ם
 0←→64  
NO  
YES  
YES  
YES  
YES  
NO  
22  
22  
22  
22  
22  
22  
22  
22  
H-WIDTH  
מ
←→
ם
 0←→64  
AUTO PICTURE  
FINE PICTURE*1  
PICTURE ADJ.*1  
ON←→OFF*2  
מ
←→
ם
*2 0←→64  
YES  
YES  
מ
←→
ם
*2 0←→128  
Main menu  
Sub menu  
Sub menu 2  
Sub menu 3  
Sub menu 4  
RESET  
REFERENCE  
SET UP  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
ENGLISH/DEUTSCH/FRANÇAIS/ESPAÑOL/ITALIANO/SVENSKA/  
RGB←→COMPONENT  
RGB  
1080I/1035I/540P  
AUTO/STILL/MOTION/WIDE1/WIDE2/WIDE3/DTV  
/ꢀУꢁꢁꢂꢃꢄ  
NO  
YES  
YES  
NO  
YES  
NO  
NO  
NO  
YES  
YES  
YES  
YES  
23  
23  
23  
23  
23  
24  
24  
24  
24  
25  
25  
25  
25  
25  
PLUG/PLAY  
PC←→STB/DVD  
BLACK LEVEL  
LOW←→HIGH  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
DISPLAY OSM  
OSM ADJ.  
AUTO/PAL/PAL-M/PAL-N/PAL 60/SECAM/4.43 NTSC/3.58NTSC  
BLACK/GRAY  
…
…
0← →3← →15  
AUTO←→OFF  
ON←→OFF  
TOP LEFT←→TOP CENTER←→TOP RIGHT←→BTM LEFT←→BTM CENTER←→BTM RIGHT YES  
ON←→OFF  
ALL RESET  
—
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Main menu  
Sub menu  
Sub menu 2  
Sub menu 3  
Sub menu 4  
RESET  
REFERENCE  
FUNCTION  
POWER MGT.  
INPUT SKIP  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
ON←→OFF  
ON←→OFF  
AUTO←→OFF  
YES  
YES  
YES  
YES  
26  
26  
26  
27  
27  
27  
28  
28  
28  
28  
28  
29  
29  
29  
29  
OFF←→S BY S←→BTM LEFT←→BTM RIGHT←→TOP RIGHT←→TOP LEFT  
OFF←→S BY S1←→S BY S2←→BTM LEFT←→BTM RIGHT←→TOP RIGHT←→TOP LEFT YES  
MANUAL/AUTO  
PEAK BRIGHT  
ORBITER  
INVERSE/WHITE OFF/INVERSE/WHITE  
SCREEN WIPER ON/OFF  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST LOW/NORMAL  
OFF/CAPTION1-4/TEXT1-4  
LOW/NORMAL  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
YES  
100%/75%/50%/25%  
OFF/AUTO1/AUTO2  
OFF/LEVEL1-4  
ON/OFF  
CLOSED CAPTION  
CAPTION CONT  
Main menu  
Sub menu  
Sub menu 2  
Sub menu 3  
Sub menu 4  
RESET  
REFERENCE  
SIGNAL INFO.  
—
29  
*1 Only when AUTO PICTURE is OFF.  
*2 RGB/PC only  
Information  
Ⅵ Restoring the factory default settings  
Select “ALL RESET” under the SET UP menu. Note that this also restores other settings to the factory defaults.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the picture  
The contrast, brightness, sharpness, color and tint can be  
adjusted as desired.  
Picture Settings Menu  
Storing picture settings  
This function allows you to store in memory the current  
input signal and PICTURE menu settings and to recall  
these settings when necessary.  
There are six picture memories, and notes of up to 15  
characters can be added to each.  
Example: Adjusting the contrast  
On “CONTRAST”of “PICTURE”menu, adjust the contrast.  
PICTURE  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
:
OFF  
Example: Storing picture settings at MEMORY1  
R
G
TINT  
On “PICTURE MEMORY” of “PICTURE” menu, select  
“MEMORY1”, then press the MENU/ENTER button.  
The “PICTURE MEMORY” screen appears.  
NR  
:
:
:
:
:
OFF  
MIDDLE  
2.2  
AUTO  
0%  
COLOR TEMP.  
GAMMA  
CONTRAST  
10  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
:
:
ON  
NORMAL  
1/2  
PICTURE MEMORY  
PREVIOUS PAGE  
2/2  
PICTURE MEMORY  
SET  
MEMORY1  
RESET  
SEL.  
ADJ.  
EXIT  
RETURN  
INPUT : DVD/HD1  
SIGNAL : 480P  
MEMORY4  
INPUT : —  
SET  
RESET  
NOTE : DVD/STAR WARS  
MEMORY2  
INPUT : —  
SIGNAL : —  
NOTE : —  
SIGNAL : —  
NOTE : —  
MEMORY5  
INPUT : —  
SIGNAL : —  
NOTE : —  
Note:If “CAN NOT ADJUST” appears ...  
When trying to enter the PICTURE submenu, make sure  
PICTURE MODE is not set to DEFAULT.  
MEMORY3  
INPUT : —  
SIGNAL : —  
NOTE : —  
MEMORY6  
INPUT : —  
SIGNAL : —  
NOTE : —  
Information  
Ⅵ Picture adjustment screen  
NEXT PAGE  
SEL.  
ADJ.  
MENU/ENTER OK  
EXIT  
SEL.  
ADJ.  
MENU/ENTER OK  
EXIT RETURN  
RETURN  
CONTRAST: Changes the picture’s white level.  
BRIGHTNESS: Changes the picture’s black level.  
SHARPNESS: Changes the picture’s sharpness.  
Adjusts picture detail of VIDEO display.  
COLOR: Changes the color density.  
TINT: Changes the picture’s tint. Adjust for natural  
colored skin, background, etc.  
Ⅵ Adjusting the computer image  
Only the contrast and brightness can be adjusted when  
a computer signal is connected.  
Information  
Ⅵ PICTURE MEMORY Settings  
OFF: Picture memory not used.  
MEMORY1 to 6: Picture memory with the specified  
number used. Maximum memories are 6, not depending  
on inputs.  
Ⅵ Setting the memory  
• Use the LLand L button to select the desired memory  
place, MEMORY1 to MEMORY6.  
Ⅵ Restoring the factory default settings  
Select “DEFAULT” under the “PICTURE MODE”  
settings.  
ᮤ
ᮣ
• Use the and buttons to select “SET”, then press  
the MENU/ENTER button.  
• If necessary, input a note.  
Ⅵ Resetting the memory  
Use the LLand L button to select the desired memory  
place, MEMORY1 to MEMORY6, then use the and  
Reducing noise in the picture  
Use these settings if the picture has noise due to poor  
reception or when playing video tapes on which the picture  
quality is poor.  
ᮤ
ᮣ
buttons to select “RESET”, and finally press the  
MENU/ENTER button.  
Example: Setting “NR-3”  
The memory is cleared, and “—” is displayed in the  
“INPUT”, “SIGNAL” and “NOTE” columns.  
Ⅵ Inputting notes  
On “NR” of “PICTURE” menu, select “NR-3”.  
PICTURE  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
:
OFF  
ᮤ
ᮣ
• Use the and buttons to select “NOTE”, then press  
the MENU/ENTER button.  
R
G
TINT  
NR  
:
:
:
:
:
OFF  
MIDDLE  
2.2  
AUTO  
0%  
• Input the note.  
COLOR TEMP.  
GAMMA  
NR  
:
NR-3  
Use the LLand L button to select the character.  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
ᮤ
ᮣ
Use the and buttons to move the cursor.  
Use the EXIT button to delete the character at the  
cursor position.  
:
:
ON  
NORMAL  
SEL.  
ADJ.  
EXIT  
RETURN  
• When you have finished inputting the note, press the  
MENU/ENTER button.  
Information  
Ⅵ NR  
* “NR” stands for Noise Reduction.  
* This function reduces noise in the picture.  
Ⅵ Types of noise reduction  
There are three types of noise reduction. Each has a  
different level of noise reduction.  
The effect becomes stronger as the number increases  
(in the order NR-1 → NR-2 → NR-3).  
OFF: Turns the noise reduction function off.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the color temperature  
Use this procedure to set color tone produced by the plasma  
display.  
Changing the Gamma Curve  
This feature adjusts the brightness of the midtone areas  
while keeping shadows and highlights unchanged.  
Example: Setting “HIGH”  
Example: Setting “2.3”  
On “COLORTEMP.” of “PICTURE” menu, select “HIGH”.  
On “GAMMA” of “PICTURE” menu, select “2.3”.  
PICTURE  
PICTURE  
:
OFF  
:
OFF  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
R
R
G
G
TINT  
TINT  
:
:
:
:
:
OFF  
HIGH  
2.2  
AUTO  
0%  
:
:
:
:
:
OFF  
MIDDLE  
2.3  
AUTO  
0%  
NR  
NR  
COLOR TEMP.  
GAMMA  
COLOR TEMP.  
GAMMA  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
:
:
ON  
NORMAL  
:
:
ON  
NORMAL  
SEL.  
ADJ.  
EXIT  
SEL.  
ADJ.  
EXIT  
RETURN  
RETURN  
Information  
Information  
Ⅵ Setting the color temperature  
Ⅵ GAMMA settings  
LOW: Redder  
The picture becomes darker as the number increases  
(in the sequence of 2.1, 2.2, 2.3, 2.4).  
MIDDLE LOW: Slightly red  
MIDDLE: Standard (slightly bluer)  
HIGH: Bluer  
* These values are approximate.  
Making the Low Tone adjustments  
This feature allows more detailed tone to be reproduced  
especially in the dark area.  
Adjusting the color to the desired level  
Use this procedure to adjust the white balance for each  
color temperature to achieve the desired color quality.  
Example: Setting “2”  
Example: Adjusting the “GAIN RED” of “HIGH” color  
temperature  
On “LOW TONE” of “PICTURE” menu, select “2”.  
PICTURE  
:
OFF  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
TINT  
NR  
COLOR TEMP.  
GAMMA  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
On “COLORTEMP.” of “PICTURE” menu, select “HIGH”,  
then press the MENU/ENTER button.  
The “WHITE BALANCE” screen appears.  
R
G
On “GAIN RED”, adjust the white balance.  
:
:
:
:
:
OFF  
MIDDLE  
2.2  
2
0%  
WHITE BALANCE  
COLOR TEMP. HIGH  
GAIN RED  
GAIN GREEN  
GAIN BLUE  
BIAS RED  
BIAS GREEN  
BIAS BLUE  
:
:
ON  
NORMAL  
RESET  
SEL.  
:
OFF  
SEL.  
ADJ.  
EXIT  
RETURN  
GAIN RED  
20  
ADJ.  
EXIT  
RETURN  
Information  
Ⅵ LOW TONE settings  
Information  
Ⅵ Adjusting the white balance  
AUTO: Will automatically appraise the picture and  
make adjustments.  
1: Will apply the dither method suitable for still pictures.  
2: Will apply the dither method suitable for motion  
pictures.  
GAIN R/G/B:White balance adjustment for white level  
BIAS R/G/B: White balance adjustment for black level  
RESET: Resets settings to the factory default values.  
ᮤ
ᮣ
Use  
and buttons to select “ON”, then press the  
MENU/ENTER button.  
Ⅵ Restoring the factory default settings  
Select “RESET” under the WHITE BALANCE menu.  
3: Will apply the error diffusion method.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Adjusting the pedestal level (black level)  
Setting the picture to suit the movie  
This feature adjusts the video black level in a video image.  
The film image is automatically discriminated and  
projected in an image mode suited to the picture.  
[NTSC, PAL, PAL60, 480I (60Hz), 525I (60Hz), 576I  
(50Hz), 625I (50Hz), 1035I (60Hz), 1080I (60Hz) only]  
Example: Setting “3.75%”  
On “SET UP LEVEL”of “PICTURE”menu, select “3.75%”.  
PICTURE  
Example: Setting the “CINEMA MODE” to “OFF”  
:
OFF  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
TINT  
NR  
COLOR TEMP.  
GAMMA  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
On “CINEMA MODE”of “PICTURE”menu, select “OFF”.  
PICTURE  
R
G
:
OFF  
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
:
:
:
:
:
OFF  
MIDDLE  
2.2  
AUTO  
3.75%  
R
G
TINT  
:
:
:
:
:
OFF  
MIDDLE  
2.2  
AUTO  
0%  
NR  
:
:
ON  
NORMAL  
COLOR TEMP.  
GAMMA  
SEL.  
ADJ.  
EXIT  
RETURN  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
Information  
:
:
OFF  
NORMAL  
Ⅵ SET UP LEVEL settings  
SEL.  
ADJ.  
EXIT  
RETURN  
0%: Normal status  
3.75%: 3.5% lower than normal  
7.5%: 7.5% lower than normal  
Information  
Ⅵ CINEMA MODE  
ON: Automatic discrimination of the image and  
projection in cinema mode.  
OFF: Cinema mode does not function.  
Adjusting the colors  
Use this procedure to adjust hue and color density for red,  
green, blue, yellow, magenta and cyan.  
You can accentuate the green color of trees, the blue of  
the sky, etc.  
Setting the picture mode according to the  
brightness of the room  
There are four picture modes that can be used effectively  
according to the environment in which you are viewing  
the display.  
Example: Adjusting the color tune for blue  
On “PICTURE” menu, select “COLOR TUNE”, then press  
the MENU/ENTER button.  
The “COLOR TUNE” screen appears.  
Example: Setting the “THEATER1” mode  
On “PICTURE MODE” of “PICTURE” menu, select  
On “BLUE” of “COLOR TUNE”, adjust the color tune.  
“THEATER1”.  
COLOR TUNE  
Y
M
Y
RED  
GREEN  
BLUE  
YELLOW  
MAGENTA  
CYAN  
PICTURE  
C
PICTURE MEMORY  
CONTRAST  
BRIGHTNESS  
SHARPNESS  
COLOR  
:
OFF  
M
G
R
B
C
R
B
G
R
G
TINT  
NR  
:
:
:
:
:
OFF  
MIDDLE  
2.2  
AUTO  
0%  
:
OFF  
RESET  
SEL.  
COLOR TEMP.  
GAMMA  
ADJ.  
EXIT  
RETURN  
PICTURE MODE  
:
THEATER1  
LOW TONE  
SET UP LEVEL  
COLOR TUNE  
CINEMA MODE  
PICTURE MODE  
Information  
:
:
ON  
NORMAL  
Ⅵ COLOR TUNE settings  
SEL.  
ADJ.  
EXIT  
RETURN  
RED: Makes red’s adjustment  
Information  
Ⅵ Types of picture modes  
THEATER1, 2: Set this mode when watching video in a  
dark room.  
This mode provides darker, finer pictures, like the screen  
in movie theaters.  
For a darker image, select THEATER2.  
NORMAL: Set this mode when watching video in a bright  
room.  
GREEN: Makes green’s adjustment  
BLUE: Makes blue’s adjustment  
YELLOW: Makes yellow’s adjustment  
MAGENTA: Makes magenta’s adjustment  
CYAN: Makes cyan’s adjustment  
RESET: Resets settings to the factory default value.  
ᮤ
ᮣ
Use  
and buttons to select “ON”, then press the  
MENU/ENTER button.  
This mode provides dynamic pictures with distinct  
differences between light and dark sections.  
BRIGHT: This mode provides brighter pictures than  
NORMAL.  
DEFAULT: Use this to reset the picture to the factory  
default settings.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Audio Settings Menu  
Image Adjust Settings Menu  
Adjusting the Position, Size, Fine Picture, Picture Adj  
The position of the image can be adjusted and flickering  
of the image can be corrected.  
Adjusting the treble, bass and left/right  
balance and audio input select  
The treble, bass and left/right balance can be adjusted to  
suit your tastes.  
Example:Adjusting the vertical position in the normal  
mode  
Example: Adjusting the bass  
On “BASS” of “AUDIO” menu, adjust the bass.  
On “V-POSITION” of “IMAGEADJUST” menu, adjust the  
position.  
AUDIO  
BASS  
TREBLE  
ᮤ
ᮣ
The mode switches as follows each time the or button is  
pressed:  
BALANCE  
AUDIO INPUT1  
AUDIO INPUT2  
AUDIO INPUT3  
:
:
:
VIDEO1  
HD/DVD1  
RGB1  
NORMAL ↔ ANAMORPHIC  
* The mode can also be switched by pressing the WIDE  
button on the remote control.  
SEL.  
ADJ.  
EXIT  
RETURN  
* The settings on the IMAGE ADJUST menu are not preset  
at the factory.  
Note :If “CAN NOT ADJUST” appears...  
Set “AUDIO INPUT” on the AUDIO menu correctly.  
IMAGE ADJUST  
:
NORMAL  
ASPECT MODE  
V-POSITION  
H-POSITION  
V-HEIGHT  
Information  
Ⅵ Audio settings menu  
BASS: Controls the level of low frequency sound.  
TREBLE: Controls the level of high frequency sound.  
BALANCE: Controls the balance of the left and right  
channels.  
H-WIDTH  
:
OFF  
AUTO PICTURE  
FINE PICTURE  
PICTURE ADJ.  
V-POSITION  
-30  
SEL.  
ADJ.  
EXIT  
RETURN  
Information  
Ⅵ When “AUTO PICTURE” is “OFF”  
Setting the allocation of the audio connectors  
Setting the AUDIO 1, 2, and 3 connectors to the desired  
input.  
IMAGE ADJUST  
:
ANAMORPHIC  
ASPECT MODE  
V-POSITION  
H-POSITION  
V-HEIGHT  
Example: Setting “AUDIO INPUT1” to “VIDEO 2”  
H-WIDTH  
:
OFF  
AUTO PICTURE  
FINE PICTURE  
PICTURE ADJ.  
On “AUDIO INPUT1” of “AUDIO” menu, select  
“VIDEO2”.  
SEL.  
ADJ.  
EXIT  
RETURN  
The available sources depend on the settings of input.  
When Auto Picture is off, the Fine Picture and the  
Picture ADJ. items are displayed so that you can adjust  
them.  
AUDIO  
BASS  
TREBLE  
BALANCE  
AUDIO INPUT1  
AUDIO INPUT2  
AUDIO INPUT3  
:
:
:
VIDEO2  
HD/DVD1  
RGB1  
Ⅵ Adjusting the Auto Picture  
ON: The Picture ADJ., Fine Picture and Position  
adjustments are made automatically.  
Not available for digital ZOOM.  
SEL.  
ADJ.  
EXIT  
RETURN  
OFF: The Picture ADJ., Fine Picture and Position  
adjustments are made manually.  
Information  
Ⅵ AUDIO INPUT  
A single audio input cannot be selected as the audio  
channel for more than one input terminal.  
* If FINE PICTURE can’t be adjusted, set Auto Picture  
to OFF and adjust manually.  
Ⅵ Adjusting the position of the image  
V-POSITION: Adjusts the vertical position of the  
image.  
H-POSITION: Adjusts the horizontal position of the  
image.  
V-HEIGHT: Adjusts the vertical size of the image.  
(Except for STADIUM mode)  
H-WIDTH: Adjusts the horizontal size of the image.  
(Except for STADIUM mode)  
FINE PICTURE*: Adjusts for flickering.  
PICTURE ADJ.*: Adjusts for striped patterns on the  
image.  
* The PictureADJ. and Fine Picture features are available  
only when the “Auto Picture” is off.  
* TheAUTO PICTURE, FINE PICTURE and PICTURE  
ADJ. are available only for RGB signals.  
But, these features are not available for moving pictures  
on VIDEO, HD/DVD or RGB.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Checking the signal being transmitted to  
RGB1 terminal  
Use this to confirm the signal being transmitted to the  
RGB1 terminal.  
It is set to RGB and can not be adjusted.  
SET UP  
SET UP Settings Menu  
Setting the language for the menus  
The menu display can be set to one of eight languages.  
Example: Setting the menu display to “DEUTSCH”  
On “LANGUAGE”of “SET UP”menu, select “DEUTSCH”.  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
SET UP  
:
:
:
:
:
DEUTSCH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
OFF  
ON  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
OFF  
ON  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
OFF  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
OFF  
CAN NOT ADJUST  
SEL.  
ADJ.  
EXIT  
RETURN  
Setting high definition images to the suitable  
screen size  
Use this procedure to set whether the number of vertical  
lines of the input high definition image is 1080I or 1035I  
or 540P.  
Information  
Ⅵ Language settings  
ENGLISH ........English  
DEUTSCH....... German  
FRANÇAIS ...... French  
ESPAÑOL .......Spanish  
ITALIANO ........Italian  
SVENSKA ....... Swedish  
................... Chinese  
Example: Setting the “HD SELECT” mode to “1035I”  
On “HD SELECT” of “SET UP” menu, select “1035I”.  
ꢀУꢁꢁꢂꢃꢄ ............Russian  
SET UP  
Setting the BNC connectors  
Select whether to set the input of the 5 BNC connectors to  
RGB and component.  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1035I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
Example: Set the BNC INPUT mode to “RGB”  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
OFF  
ON  
On “BNC INPUT” of “SET UP” menu, select “RGB”.  
SET UP  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
:
:
:
:
:
ENGLISH  
RGB  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
TOP LEFT  
OFF  
SEL.  
ADJ.  
EXIT  
RETURN  
Information  
Ⅵ HD SELECT modes  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
OFF  
ON  
These 3 modes are not displayed in correct image  
automatically.  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
OFF  
SEL.  
ADJ.  
EXIT  
RETURN  
1080I: Standard digital broadcasts  
1035I: Japanese “High Vision” signal format  
540P: Special Digital broadcasts (for example :  
DTC100)  
Information  
Ⅵ BNC INPUT Settings  
RGB: Use the 5BNC terminals for RGB input.  
COMPONENT: Use the 3BNC terminals for  
component input.  
Setting a computer image to the correct RGB  
select screen  
With the computer image, select the RGB Select mode  
for a moving image such as (video) mode, wide mode or  
digital broadcast.  
Example: Setting the “RGB SELECT” mode to  
“MOTION ”  
On “RGB SELECT”of “SET UP”menu, select “MOTION”.  
SET UP  
:
:
:
:
:
:
:
:
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
1080I  
MOTION  
1024
؂
768  
AUTO  
GRAY  
3
OFF  
ON  
TOP LEFT  
OFF  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
SEL.  
ADJ.  
EXIT  
RETURN  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the video signal format  
Use these operations to set the color systems of composite  
video signals or Y/C input signals.  
Information  
Ⅵ RGB SELECT modes  
One of these 7 modes must be selected in order to  
display the following signals correctly.  
AUTO: Select the suitable mode for the specifications  
of input signals as listed in the table “Computer input  
signals supported by this system” on page 7 of Model  
Information.  
STILL: To display VESA standard signals. (Use this  
mode for a still image from a computer.)  
MOTION: The video signal (from a scan converter)  
will be converted to RGB signals to make the picture  
more easily viewable. (Use this mode for a motion  
image from a computer.)  
Example: Setting the color system to “3.58 NTSC”  
On “COLOR SYSTEM” of “SET UP” menu, select  
“3.58NTSC”.  
SET UP  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
:
:
:
:
:
:
:
3.58NTSC  
GRAY  
3
OFF  
ON  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
OFF  
WIDE1: When an 852 dot
ן
 480 line signal with a  
horizontal frequency of 31.7kHz is input, the image may  
be compressed horizontally. To prevent this, set RGB  
SELECT to WIDE1.  
WIDE2: When an 848 dot
ן
 480 line signal with a  
horizontal frequency of 31.0 kHz is input, the image  
may be compressed horizontally. To prevent this, set  
RGB SELECT to WIDE2.  
WIDE3: When an 1920 dot
ן
 1200 line signal with a  
horizontal frequency of 74.0 kHz is input, the image  
may be compressed horizontally. To prevent this, set  
RGB SELECT to WIDE3.  
DTV: Set this mode when watching digital broadcasting  
(480P).  
SEL.  
ADJ.  
EXIT  
RETURN  
Information  
Ⅵ Video signal formats  
Different countries use different formats for video signals.  
Set to the color system used in your current country.  
AUTO: The color systems are automatically identified  
and the format is set accordingly.  
PAL: This is the standard format used mainly in the  
United Kingdom and Germany.  
SECAM: This is the standard format used mainly in  
France and Russia.  
4.43 NTSC, PAL60: This format is used for videos in  
countries using PAL and SECAM video signals.  
3.58 NTSC: This is the standard format used mainly  
in the United States and Japan.  
See page 7 of Model Information for the details of the  
above settings.  
PAL-M: This is the standard format used mainly in  
Brazil.  
PAL-N: This is the standard format used mainly in  
Argentina.  
Setting the signal and black level for DVI  
signal  
Choose the signal for the DVI connector (PC or STB/  
DVD) and set the black level.  
Example: Setting the “PLUG/PLAY” mode to “STB/  
DVD”  
Setting the background color when no signal  
is being input  
The color displayed on the background when there is no  
On “SET UP” menu, select “DVI SET UP”, then press the  
signal can be set to gray.  
MENU/ENTER button.  
The “DVI SET UP” screen appears.  
Example: Setting “BACK GROUND” to “BLACK”  
On “PLUG/PLAY” of “DVI SET UP” menu, select “STB/  
DVD”.  
On “BACK GROUND” of “SET UP” menu, select  
“BLACK”.  
DVI SET UP  
SET UP  
:
STB/DVD  
PLUG/PLAY  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
:
HIGH  
BLACK LEVEL  
:
:
:
:
:
:
:
AUTO  
BLACK  
3
OFF  
ON  
SEL.  
ADJ.  
EXIT  
RETURN  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
Information  
Ⅵ PLUG/PLAY settings  
TOP LEFT  
OFF  
SEL.  
ADJ.  
EXIT  
RETURN  
PC: When connected to the PC signal.  
BLACK LEVEL is set to “LOW” automatically.  
STB/DVD: When connected to the SET TOP BOX,  
DVD etc.  
BLACK LEVEL is set to “HIGH” automatically.  
Ⅵ BLACK LEVEL settings  
LOW: When connected to the PC signal.  
HIGH: When connected to the SET TOP BOX, DVD  
etc. Change “HIGH” into “LOW” if the black level  
appears gray.  
Information  
Ⅵ BACK GROUND Settings  
BLACK: Sets the background color to black.  
GRAY: Sets the background color to gray.  
Setting this makes it easier to see that there is no signal.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the gray level for the sides of the screen  
Use this procedure to set the gray level for the parts on the  
screen on which nothing is displayed when the screen is  
set to the 4:3 size.  
Information  
Ⅵ DISPLAY OSM settings  
ON: The on-screen menu appears.  
OFF: The on-screen menu does not appear.  
If you press the DISPLAY button on the remote control  
for more than 3 seconds the main menu will appear  
and can be set (although it is not ON).  
Example: Setting “GRAY LEVEL” to “5”  
On “GRAY LEVEL” of “SET UP” menu, select “5”.  
SET UP  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
Setting the position of the menu  
Adjusts the position of the menu when it appears on the  
screen.  
:
:
:
:
:
:
:
AUTO  
GRAY  
5
OFF  
ON  
Example: Set the position to “TOP CENTER”  
On “OSMADJ.”of “SETUP”menu, select “TOPCENTER”.  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
OFF  
SET UP  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
SEL.  
ADJ.  
EXIT  
RETURN  
Information  
Ⅵ GRAY LEVEL settings  
This adjusts the brightness of the black (the gray level)  
for the sides of the screen.  
The standard is 0 (black). The level can be adjusted  
from 0 to 15. The factory setting is 3 (dark gray).  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
OFF  
ON  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP CENTER  
OFF  
SEL.  
ADJ.  
EXIT  
RETURN  
Setting the screen size for S1/S2 video input  
If the S-video signal contains screen size information, the  
image will be automatically adjusted to fit the screen when  
this S1/S2 is set to AUTO.  
Information  
Ⅵ OSM ADJUST settings  
This feature is available only when an S-video signal is  
input via the VIDEO3 terminal.  
TOP  
RIGHT  
TOP  
LEFT  
TOP  
CENTER  
Example: Setting “S1/S2” to “AUTO”  
BTM  
BTM  
BTM  
LEFT  
RIGHT  
CENTER  
On “S1/S2” of “SET UP” menu, select “AUTO”.  
SET UP  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
Resetting to the default values  
Use these operations to restore all the settings (PICTURE,  
AUDIO, IMAGE ADJUST, SET UP, etc) to the factory  
default values.  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
AUTO  
ON  
Refer to page 17 for items to be reset.  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
OFF  
On “ALL RESET” of “SET UP” menu, select “ON”, then  
SEL.  
ADJ.  
EXIT  
press the MENU/ENTER button.  
RETURN  
SET UP  
ALL RESET  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
Information  
Ⅵ S1/S2 settings  
AUTO: Adjusts the screen size automatically according  
to the S1/S2 video signal.  
OFF: Turns the S1/S2 function off.  
SETTING NOW  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
OFF  
ON  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
ON  
SEL.  
ADJ.  
EXIT  
RETURN  
Turning on/off the menu display  
When this is set to OFF, the menu will not displayed even  
When the “SETTING NOW” screen disappears, then all the  
if you press the MENU/ENTER button.  
settings are restored to the default values.  
Example: Turning the DISPLAY OSM off  
On “DISPLAY OSM” of “SET UP” menu, select “OFF”.  
SET UP  
:
:
:
:
:
ENGLISH  
COMPONENT  
RGB  
1080I  
AUTO  
LANGUAGE  
BNC INPUT  
D-SUB INPUT  
HD SELECT  
RGB SELECT  
DVI SET UP  
COLOR SYSTEM  
BACK GROUND  
GRAY LEVEL  
S1/S2  
:
:
:
:
:
:
:
AUTO  
GRAY  
3
OFF  
OFF  
DISPLAY OSM  
OSM ADJ.  
ALL RESET  
TOP LEFT  
OFF  
SEL.  
ADJ.  
EXIT  
RETURN  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Setting the Input Skip  
Function Settings Menu  
When this is ON, signals which are not present will be  
skipped over and only pictures whose signals are being  
transmitted will be displayed.  
This setting is valid only for the INPUT SELECT button  
on the unit.  
Setting the power management for computer  
images  
This energy-saving (power management) function  
automatically reduces the monitor’s power consumption  
if no operation is performed for a certain amount of time.  
Example: Set to “ON”  
Example: Turning the power management function on  
On “INPUT SKIP” of “FUNCTION” menu, select “ON”.  
On “POWER MGT.” of “FUNCTION” menu, select “ON”.  
FUNCTION  
FUNCTION  
:
:
:
:
:
:
:
:
OFF  
ON  
POWER MGT.  
INPUT SKIP  
:
:
:
:
:
:
:
:
ON  
OFF  
POWER MGT.  
INPUT SKIP  
AUTO  
BTM LEFT  
S BY S1  
MANUAL  
OFF  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
CLOSED CAPTION  
CAPTION CONT  
AUTO  
BTM LEFT  
S BY S1  
MANUAL  
OFF  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
CLOSED CAPTION  
CAPTION CONT  
LOW  
LOW  
SEL.  
ADJ.  
EXIT  
RETURN  
SEL.  
ADJ.  
EXIT  
RETURN  
Information  
Ⅵ INPUT SKIP settings  
Information  
Ⅵ Power management function  
OFF: Regardless of the presence of the signal, scan  
and display all signals.  
ON: If no input signal is present, skip that signal.  
* The power management function automatically reduces  
the monitor’s power consumption if the computer’s  
keyboard or mouse is not operated for a certain amount  
of time. This function can be used when using the  
monitor with a computer.  
* “SETTING NOW” will appear during the input search.  
Erasing the sub screen image when there is  
no input signal  
This function automatically erases the black frame of the  
sub screen when there is no sub screen input signal.  
This feature is available only when the picuture-in-picuture  
mode is selected.  
* If the computer’s power is not turned on or if the  
computer and selector tuner are not properly connected,  
the system is set to the off state.  
* For instructions on using the computer’s power  
management function, refer to the computer’s operating  
instructions.  
Ⅵ Power management settings  
ON: In this mode the power management function is  
turned on.  
Example: Set to “OFF”  
On “SUB. P DETECT” of “FUNCTION” menu, select  
“OFF”.  
OFF: In this mode the power management function is  
turned off.  
Ⅵ Power management function and POWER/  
STANDBY indicator  
The POWER/STANDBY indicator indicates the status  
of the power management function. See below for  
indicator status and description.  
FUNCTION  
:
:
:
:
:
:
:
:
OFF  
OFF  
OFF  
BTM LEFT  
S BY S1  
MANUAL  
OFF  
POWER MGT.  
INPUT SKIP  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
CLOSED CAPTION  
CAPTION CONT  
LOW  
SEL.  
ADJ.  
EXIT  
RETURN  
Information  
Ⅵ SUB. P DETECT Function  
POWER/STANDBY indicator  
Power  
POWER/  
Power  
management  
operating status  
Description  
Turning the picture  
back on  
* The sub screen disappears when the input signal is lost.  
* Loss of the input signal means a condition in which the  
video signal and the sync signal are not present.  
* Under conditions in which the sub screen has  
disappeared, the ZOOM NAV and PICTURE FREEZE  
functions will not work. The WIDE button will not  
function either.  
management STANDBY  
mode  
indicator  
On  
Green  
Not activated.  
Activated.  
Horizontal and vertical Picture already on.  
synchronizing signals  
are present from the  
computer.  
Off  
Red  
Horizontal and/or Operate the keyboard or  
vertical synchronizing mouse. The picture  
signals are not sent reappears.  
from the computer.  
Ⅵ SUB. P DETECT settings  
AUTO: The black frame disappears 3 seconds after the  
input signal is lost.  
OFF: Turns off the SUB. P DETECT function.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Displaying the entire image during DIGITAL  
ZOOM operations  
Use this function to display the entire image within the  
sub screen together with an enlarged image on the main  
screen.  
FUNCTION  
:
:
:
:
:
:
:
:
OFF  
OFF  
AUTO  
BTM LEFT  
BTM LEFT  
MANUAL  
OFF  
POWER MGT.  
INPUT SKIP  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
CLOSED CAPTION  
CAPTION CONT  
LOW  
Example: Setting “ZOOM NAV” to “S BY S”  
SEL.  
ADJ.  
EXIT  
RETURN  
On “ZOOM NAV” of “FUNCTION” menu, select “S BY  
S”.  
Information  
Ⅵ PICTURE FREEZE Function  
FUNCTION  
:
:
:
:
:
:
:
:
OFF  
OFF  
POWER MGT.  
INPUT SKIP  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
CLOSED CAPTION  
CAPTION CONT  
* This feature is available only for RGB1 or RGB2 input  
signals.  
* This feature does not function during multi screen mode.  
* Digital zoom is not available while this function is  
operating.  
AUTO  
S BY S  
S BY S1  
MANUAL  
OFF  
LOW  
SEL.  
ADJ.  
EXIT  
RETURN  
* A further press of the ACTIVE SELECT button while  
this function is operating will cancel this function.  
* Providing a 2-screen display will cancel this function.  
Ⅵ PICTURE FREEZE settings  
Information  
Ⅵ ZOOM NAV Function  
* This feature is available only for RGB1 or RGB2 input  
signals.  
* This feature does not function during multi screen mode.  
* This feature does not function while PICTURE FREEZE  
is operating.  
* Providing a 2-screen display will cancel this function.  
Ⅵ ZOOM NAV settings  
OFF: Will not show the entire image on the sub screen.  
S BY S: Will show the entire image on the sub screen  
of side-by-side mode.  
OFF: Will not show the still image.  
S BY S1, 2: The still images captured by pressing the  
ACTIVE SELECT button will be shown on the sub  
screen of side-by-side mode.  
BTM LEFT~TOP LEFT: The still images captured by  
pressing the ACTIVE SELECT button will be shown  
on the sub screen of picture-in-picture mode.  
Side-by-Side  
Picture-in-Picture  
RGB/PC1  
RGB/PC1  
BTM LEFT~TOP LEFT: Will show the entire image  
on the sub screen of picture-in-picture mode.  
Side-by-Side  
Picture-in-Picture  
RGB/PC1  
ACTIVE  
SELECT  
button  
RGB/PC1  
ACTIVE  
SELECT  
button  
RGB/PC1  
RGB/PC1  
S BY S1  
RGB/PC1  
RGB/PC1  
Zoom+/- button  
or  
S BY S2  
RGB/PC1  
RGB/PC1  
SINGLE button  
Reducing burn-in of the screen  
The brightness of the screen, the position of the picture,  
positive/negative mode and screen wiper are adjusted to  
reduce burn-in of the screen.  
On “PDP SAVER” of “FUNCTION” menu, select  
“MANUAL”, then press the MENU/ENTER button.  
The “PDP SAVER” screen appears.  
Displaying still images in the sub screen  
This feature enables display in the sub screen of still images  
captured by pressing the ACTIVE SELECT button.  
Example: Setting “PICTURE FREEZE” to “BTM  
LEFT”  
PDP SAVER  
:
:
:
:
:
:
:
100%  
OFF  
OFF  
OFF  
OFF  
ON  
PEAK BRIGHT  
ORBITER  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
On “PICTURE FREEZE” of “FUNCTION” menu, select  
“BTM LEFT”.  
LOW  
SEL.  
ADJ.  
EXIT  
RETURN  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INVERSE/WHITE  
Information  
Use this to set the inverse mode or to display a white  
screen.  
Ⅵ When set to AUTO  
Set automatically, as described below.  
PEAK BRIGHT: 100%  
ORBITER: ON  
Example: Setting “INVERSE/WHITE” to “WHITE”  
On “INVERSE/WHITE” of “PDP SAVER” menu, select  
INVERSE/WHITE: OFF  
SCREEN WIPER: OFF  
SOFT FOCUS: OFF  
OSD ORBITER: ON  
OSD CONTRAST: LOW  
“WHITE”.  
PDP SAVER  
:
:
:
:
:
:
:
100%  
OFF  
WHITE  
OFF  
OFF  
ON  
PEAK BRIGHT  
ORBITER  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
LOW  
PEAK BRIGHT  
SEL.  
ADJ.  
EXIT  
RETURN  
Use this to activate the brightness limiter.  
Example: Setting “PEAK BRIGHT” to “75%”  
On “PEAK BRIGHT”of “PDPSAVER”menu, select “75%”.  
PDP SAVER  
Information  
Ⅵ INVERSE/WHITE Settings  
OFF: Inverse/white mode does not function.  
INVERSE:The picture is displayed alternately between  
positive image and negative image.  
:
:
:
:
:
:
:
75%  
OFF  
OFF  
OFF  
OFF  
ON  
PEAK BRIGHT  
ORBITER  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
WHITE: The entire screen turns white.  
LOW  
SEL.  
ADJ.  
EXIT  
RETURN  
SCREEN WIPER  
When this is set to ON, a white vertical bar moves  
repeatedly from the left and of the screen to the right end  
at a constant speed.  
Information  
Ⅵ PEAK BRIGHT settings  
Example: Setting “SCREEN WIPER” to “ON”  
100%: The brightness of the screen is adjusted  
automatically to suit the picture quality.  
On “SCREEN WIPER” of “PDP SAVER” menu, select  
75%, 50%, 25%: Sets maximum brightness.  
The brightness level decreases in the order of 75%,  
50%, 25%. 25% provides minimum brightness.  
“ON”.  
PDP SAVER  
:
:
:
:
:
:
:
100%  
OFF  
OFF  
ON  
OFF  
ON  
PEAK BRIGHT  
ORBITER  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
* These values are approximate.  
ORBITER  
LOW  
SEL.  
ADJ.  
EXIT  
RETURN  
Use this to set the picture shift.  
Example: Setting “ORBITER” to “AUTO1”  
On “ORBITER” of “PDP SAVER” menu, select “AUTO1”.  
PDP SAVER  
Information  
Ⅵ SCREEN WIPER  
:
:
:
:
:
:
:
100%  
AUTO1  
OFF  
OFF  
OFF  
PEAK BRIGHT  
ORBITER  
ON: The white vertical bar appears.  
OFF: Screen wiper mode does not function.  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
SOFT FOCUS  
ON  
LOW  
SEL.  
ADJ.  
EXIT  
Reduces edges and softens the image.  
Example: Setting “SOFT FOCUS” to “LEVEL2”  
RETURN  
Information  
On “SOFT FOCUS” of “PDP SAVER” menu, select  
Ⅵ ORBITER settings  
“LEVEL2”.  
OFF: Orbiter mode does not function.  
PDP SAVER  
:
:
:
:
:
:
:
100%  
OFF  
OFF  
OFF  
LEVEL2  
ON  
PEAK BRIGHT  
ORBITER  
This is the default setting when RGB is input.  
AUTO1: The picture moves around the screen  
intermittently, making the picture smaller. This is the  
default setting when a Video or a DVD/HD/DTV signal  
is input. Set to “OFF” when these signals are not used.  
AUTO2: The picture moves around the screen  
intermittently, making the picture bigger.  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
LOW  
SEL.  
ADJ.  
EXIT  
RETURN  
Information  
* When a Video or a DVD/HD/DTV signal is input, the  
AUTO1 and 2 functions will affect only the moving  
picture and will not make the screen smaller or bigger.  
Ⅵ SOFT FOCUS settings  
OFF: Turns the SOFT FOCUS function off.  
LEVEL1, 2, 3, 4:Activates the SOFT FOCUS setting.  
The higher numbers create a softer image.  
“SHARPNESS” can not be adjusted on the  
“PICTURE” menu.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OSM ORBITER  
Information  
Use this to set OSM menu shift.  
Example: Setting “OSM ORBITER” to “OFF”  
Ⅵ CLOSED CAPTION settings  
OFF: This exits the closed caption mode.  
CAPTION1~4: Text is superimposed.  
TEXT1~4: Text is displayed in full screen.  
A closed caption signal may not be decoded in the  
following signature;  
1. when a video tape has been dubbed.  
2. when the signal reception is weak.  
3. when the signal reception is nonstandard.  
When using closed captioned channel or the text mode,  
the text screen always appears.  
On “OSM ORBITER” of “PDP SAVER” menu, select  
“OFF”.  
PDP SAVER  
:
:
:
:
:
:
:
100%  
OFF  
OFF  
OFF  
OFF  
OFF  
LOW  
PEAK BRIGHT  
ORBITER  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
SEL.  
ADJ.  
EXIT  
RETURN  
When there is no signal, however, the text screen will  
not display text characters.  
Information  
Ⅵ OSM ORBITER settings  
Reducing the brightness of Closed Caption  
Use this to reduce the brightness of Closed Caption.  
ON: The position of the menu will be shifted by eight  
dots each time OSM is displayed.  
OFF: OSM will be displayed at the same position.  
Example: Setting “NORMAL”  
On “CAPTION CONT” of “FUNCTION” menu, select  
“NORMAL”.  
OSM CONTRAST  
Use this to reduce the brightness of OSM menu.  
Example: Setting “OSM CONTRAST” to “NORMAL”  
FUNCTION  
:
:
:
:
:
:
:
:
OFF  
OFF  
AUTO  
BTM LEFT  
S BY S1  
MANUAL  
OFF  
POWER MGT.  
INPUT SKIP  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
CLOSED CAPTION  
CAPTION CONT  
On “OSM CONTRAST” of “PDP SAVER” menu, select  
“NORMAL”.  
PDP SAVER  
NORMAL  
:
:
:
:
:
:
:
100%  
OFF  
OFF  
OFF  
OFF  
PEAK BRIGHT  
ORBITER  
SEL.  
ADJ.  
EXIT  
RETURN  
INVERSE/WHITE  
SCREEN WIPER  
SOFT FOCUS  
OSM ORBITER  
OSM CONTRAST  
Information  
Ⅵ CAPTION CONT settings  
ON  
NORMAL  
SEL.  
ADJ.  
EXIT  
RETURN  
NORMAL: Closed Caption brightness is set to normal.  
LOW: Closed Caption brightness is set to lower.  
Information  
Ⅵ OSM CONTRAST settings  
NORMAL: OSM brightness is set to normal.  
LOW: OSM brightness is set to lower.  
Signal Information Menu  
Checking the frequencies, polarities of input  
signals, and resolution  
Use this function to check the frequencies and polarities  
of the signals currently being input from a computer, etc.  
On “MAIN MENU”, select “SIGNAL INFO.”, then press  
the MENU/ENTER button.  
Setting Closed Caption  
This function sets several closed caption modes that allows  
text to be superimposed on display.  
Example: Setting “CAPTION2”  
The “SIGNAL INFORMATION” is displayed.  
On “CLOSED CAPTION” of “FUNCTION” menu, select  
SIGNAL INFORMATION  
“CAPTION2”.  
:
:
48.4KHz  
60.0Hz  
H. FREQUENCY  
V. FREQUENCY  
FUNCTION  
:
:
NEGATIVE  
NEGATIVE  
H. POLARITY  
V. POLARITY  
:
:
:
:
:
:
:
:
OFF  
OFF  
AUTO  
BTM LEFT  
S BY S1  
MANUAL  
CAPTION2  
LOW  
POWER MGT.  
INPUT SKIP  
SUB. P DETECT  
ZOOM NAV  
PICTURE FREEZE  
PDP SAVER  
CLOSED CAPTION  
:
:
24  
MEMORY  
RESOLUTION  
1024
؂
768  
SEL.  
ADJ.  
EXIT  
RETURN  
CAPTION CONT  
PC:  
MEMORY will be displayed.  
SEL.  
ADJ.  
EXIT  
RETURN  
Others: MODE will be displayed.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
External Control Pin Assignments  
Application  
mini D-Sub 15-pin connector  
(Analog)  
These specifications cover the communications control of  
the plasma monitor by external equipment.  
RGB 1  
Connections  
Connections are made as described below.  
5
4
3
2
1
10  
9
8
7
6
15 14 13 12 11  
External equipment  
e.g., Personal computer  
Pin No.  
Signal (Analog)  
1
2
3
Red  
Green or sync-on-green  
Blue  
4
5
No connection  
Ground  
6
Red ground  
7
Green ground  
8
Blue ground  
9
No connection  
Sync signal ground  
No connection  
Bi-directional DATA (SDA)  
Horizontal sync or Composite sync  
Vertical sync  
Display  
10  
11  
12  
13  
14  
15  
Connector on the plasma monitor side: EXTERNAL  
CONTROL connector.  
Use a crossed (reverse) cable.  
Data clock  
Type of connector: D-Sub 9-pin male  
Pin No.  
Pin Name  
No Connection  
RXD (Receive data)  
TXD (Transmit data)  
DTR (DTE side ready)  
GND  
Pin No.  
Pin Name  
1
2
3
4
5
6
7
8
9
DSR (DCE side ready)  
RTS (Ready to send)  
CTS (Clear to send)  
No connection  
DVI-D 24-pin connector (Digital)  
The unit is equipped with a type of connector commonly  
used for digital.  
(This cannot be used for an analog input.)  
(TMDS can be used for one link only.)  
2
5
1
3
4
RGB 3  
8
9
6
7
1
9
2
3
4
5
6
7
8
Communication Parameters  
10 11 12 13 14 15 16  
(1) Communication system  
(2) Interface  
Asynchronous  
17 18 19 20 21 22 23 24  
RS-232C  
9600 bps  
8 bits  
(3) Baud rate  
(4) Data length  
(5) Parity  
Pin No.  
1
Signal (Digital)  
Odd  
T.M.D.S Data 2 -  
(6) Stop bit  
(7) Communication code  
1 bit  
Hex  
2
3
4
5
6
7
T.M.D.S Data 2 +  
T.M.D.S Data 2 Shield  
No connection  
No connection  
DDC Clock  
External Control Codes (Reference)  
FUNCTION  
Power ON  
OFF  
CODE DATA  
9FH 80H 60H 4EH 00H CDH  
9FH 80H 60H 4FH 00H CEH  
DDC Data  
8
9
No connection  
T.M.D.S Data 1 -  
T.M.D.S Data 1 +  
T.M.D.S Data 1 Shield  
No connection  
No connection  
+5V Power  
Input Switch Video1 (BNC)  
Video2 (RCA)  
DFH 80H 60H 47H 01H 01H 08H  
DFH 80H 60H 47H 01H 02H 09H  
DFH 80H 60H 47H 01H 03H 0AH  
DFH 80H 60H 47H 01H 05H 0CH  
DFH 80H 60H 47H 01H 06H 0DH  
DFH 80H 60H 47H 01H 0EH 15H  
Video3 (S-Video)  
DVD1/HD1 (RCA)  
DVD2/HD2 (BNC)  
DVD3/HD3 (DVI)  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
RGB1 (mini D-sub 15-pin) DFH 80H 60H 47H 01H 07H 0EH  
RGB2 (5BNC)  
RGB3 (DVI)  
DFH 80H 60H 47H 01H 08H 0FH  
DFH 80H 60H 47H 01H 0CH 13H  
Ground  
Audio Mute ON  
9FH 80H 60H 3EH 00H BDH  
9FH 80H 60H 3FH 00H BEH  
OFF  
Hot Plug Detect  
T.M.D.S Data 0 -  
T.M.D.S Data 0 +  
T.M.D.S Data 0 Shield  
No connection  
No connection  
T.M.D.S Clock Shield  
T.M.D.S Clock +  
T.M.D.S Clock -  
Picture Mode NORMAL  
THEATER 1  
DFH 80H 60H OAH 01H 01H CBH  
DFH 80H 60H OAH 01H 02H CCH  
DFH 80H 60H OAH 01H 03H CDH  
DFH 80H 60H OAH 01H 04H CEH  
DFH 80H 60H OAH 01H 05H CFH  
THEATER 2  
DEFAULT  
BRIGHT  
Screen Mode STADIUM  
ZOOM  
DFH 80H 60H 51H 01H 02H 13H  
DFH 80H 60H 51H 01H 03H 14H  
DFH 80H 60H 51H 01H 04H 15H  
DFH 80H 60H 51H 01H 05H 16H  
DFH 80H 60H 51H 01H 09H 1AH  
DFH 80H 60H 51H 01H 0AH 1BH  
NORMAL  
ANAMORPHIC  
14 : 9  
2.35 : 1  
Auto Picture ON  
OFF  
DFH 80H 60H 7FH 03H 03H 09H 00H 4DH  
DFH 80H 60H 7FH 03H 03H 09H 01H 4EH  
Cinema Mode ON  
OFF  
DFH 80H 60H C1H 01H 01H 82H  
DFH 80H 60H C1H 01H 02H 83H  
Note: Contact your local dealer for a full list of the  
30  
External Control Codes if needed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Troubleshooting  
If the picture quality is poor or there is some other problem, check the adjustments, operations, etc., before requesting service.  
Symptom  
Mechanical sound is heard.  
Checks  
Remedy  
• Maybe the sound from the cooling fans used to prevent over heating.  
The unit emits a crackling sound.  
• Are the image and sound normal?  
• If there are no abnormalities in the image and sound,  
the noise is caused by the cabinet reacting to  
changes in temperature. This will not affect  
performance.  
Picture is disturbed.  
• Is a connected component set directly in front or at • Leave some space between the display and the  
Sound is noisy.  
the side of the display?  
connected components.  
Remote control operates erroneously.  
The remote control does not work.  
• Are the remote control’s batteries worn out?  
• Replace both batteries with new ones.  
Monitor’s power does not turn on when the  
remote control’s power button is pressed.  
• Is the monitor’s power cord plugged into a power  
outlet?  
• Plug the monitor’s power cord into a power outlet.  
• Are all the monitor’s indicators off?  
• Press the power button on the monitor to turn on the  
power.  
• Are the remote control’s batteries worn out?  
• Replace both batteries with new ones.  
Monitor does not operate when the remote  
control’s buttons are pressed.  
• Is the remote control pointed at the monitor, or is  
there an obstacle between the remote control and  
the monitor?  
• Point the remote control at the monitor’s remote  
control sensor when pressing buttons, or remove the  
obstacle.  
• Is direct sunlight or strong artificial light shining on • Eliminate the light by closing curtains, pointing the  
the monitor’s remote control sensor?  
light in a different direction, etc.  
•
Are the remote control’s batteries worn out?  
• Replace both batteries with new ones.  
• Plug the monitor’s power cord into a power outlet.  
No sound or picture is produced.  
• Is the monitor’s power cord plugged into a power  
outlet?  
Picture appears but no sound is produced.  
• Is the volume set at the minimum?  
• Is the mute mode set?  
• Increase the volume.  
• Press the remote control’s MUTE button.  
• Connect the speakers properly.  
• Are the speakers properly connected?  
• Is AUDIO INPUT set correctly?  
• Set AUDIO INPUT on the AUDIO menu correctly.  
Poor picture with VIDEO signal input.  
Poor picture with RGB signal input.  
• Improper control setting.  
Local interference.  
Cable interconnections.  
• Adjust picture control as needed.  
Try another location for the monitor.  
Be sure all connections are secure.  
Input impedance is not correct level.  
• Improper control setting.  
• Adjust picture controls as needed.  
Incorrect 15 PIN connector pin connections.  
Check pin assignments and connections.  
Tint is poor or colors are weak.  
Nothing appears on screen.  
• Are the tint and colors properly adjusted?  
• Is the computer’s power turned on?  
• Is a source connected?  
• Adjust the tint and color (under PICTURE).  
• Turn on the computer’s power.  
• Connect source to the monitor.  
• Is the power management function in the standby • Operate the computer (move the mouse, etc.).  
or off mode?  
Part of picture is cut off or picture is not  
centered.  
• Is the position adjustment appropriate?  
• Adjust the IMAGE ADJUST properly.  
Image is too large or too small.  
• Is the screen size adjustment appropriate?  
• Is the computer’s resolution setting appropriate?  
• Press the WIDE button on the remote control and  
adjust properly.  
Picture is unstable.  
• Set to the proper resolution.  
• Check the input signal.  
POWER/STANDBY indicator is lighted in red. • Horizontal and / or vertical sync signal is not  
present when the Intelligent Power Manager  
control is on.  
POWER/STANDBY indicator is blinking in  
red.  
• The temperature inside the main unit has become • Promptly switch off the power of the main unit and  
too high and has activated the protector.  
wait until the internal temperature drops. See*1.  
POWER/STANDBY indicator is blinking in  
green and red, or green.  
• Prompty switch off the power of the main unit. See  
*2.  
——————  
*1 Overheat protector  
If the monitor becomes too hot, the overheat protector will be activated and the monitor will be turned off. If this happens, turn off the power to the monitor  
and unplug the power cord. If the room where the monitor is installed is particularly hot, move the monitor to a cooler location and wait for the monitor  
to cool for 60 minutes. If the problem persists, contact your dealer.  
*2 In the following case, power off the monitor immediately and contact your dealer or authorized Service Center.  
The monitor turns off 5 seconds after powering on and then the POWER/STANDBY indicator blinks. It indicates that the power supply circuit, plasma  
display panel, temperature sensor, or one or more fans have been damaged.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Limited Warranty  
Residential Entertainment Plasma Monitors  
NEC Solutions, Inc. (hereinafter NEC Solutions) warrants  
this product to be free from defects in material and  
workmanship under the following terms and, subject to the  
conditions set forth below, agrees to repair or replace (at  
NEC Solutions’ sole option) any part of the enclosed unit  
which proves defective. Replacement parts or products may  
be new or refurbished and will meet specifications of the  
original parts or products.  
HOW YOU CAN GET WARRANTY SERVICE  
1. To obtain service on your product, consult the dealer from whom  
you purchased the product.  
2. Whenever warranty service is required, the original dated invoice  
(or a copy) must be presented as proof of warranty coverage.  
Please also include in any mailing your name, address and a  
description of the problem(s).  
3. For the name of the nearest NEC Solutions authorized service  
center, call NEC Solutions at 800-836-0655.  
HOW LONG IS THE WARRANTY?  
Parts and Labor: Parts and Labor (Excluding the PDP) are  
warranted for (3) three years from the date of the first  
customer purchase.  
LIMITATIONS OF LIABILITY  
Except for the obligations specifically set forth in this  
warranty statement, we will not be liable for any direct,  
indirect, special, incidental, consequential, or other types of  
damages, whether based on contract, tort, or any other legal  
theory, whether or not we have been advised of the  
possibility of such damages. This warranty is in lieu of all  
other warranties expressed or implied, including, but not  
limited to, the implied warranties of merchantability or  
fitness for a particular purpose.  
PDP (Plasma Display Panel): The PDP is warranted for  
(1) one year from the date of the first customer purchase.  
WHO IS PROTECTED?  
This warranty may be enforced only by the first purchaser.  
WHAT IS COVERED AND WHAT IS NOT COVERED  
Except as specified below, this warranty covers all defects in  
material or workmanship in this product. The following are  
not covered by the warranty:  
EXCLUSION OF DAMAGES  
NEC Solutions’ liability for any defective product is limited  
to the repair or replacement of the product at our option.  
NEC Solutions shall not be liable for:  
1. Any product which is not distributed in the U.S.A. or Canada by  
NEC Solutions or which is not purchased in the U.S.A. or Canada  
from an authorized NEC Solutions dealer.  
1. Damage to other property caused by any defects in this product,  
damages based upon inconvenience, loss of use of the product, loss  
of time, commercial loss; or  
2. Any product of which the serial number has been defaced,  
modified or removed.  
3. Damage, deterioration or malfunction resulting from:  
a. Accident, misuse, abuse, neglect, fire, water, lightning or other  
acts of nature, unauthorized product modification, or failure to  
follow instructions supplied with the product.  
2. Any other damages whether incidental, consequential or  
otherwise. Some states do not allow limitation on how long an  
implied warranty lasts and/or do not allow the exclusion or  
limitation of incidental or consequential damages, so the above  
limitations and exclusions may not apply to you.  
b. Repair or attempted repair by anyone not authorized by NEC  
Solutions.  
c. Any shipment of the product (claims must be presented to the  
carrier).  
d. Removal or installation of the product.  
HOW STATE LAW RELATES TO THE WARRANTY  
This warranty gives you specific legal rights, and you may  
also have other rights which vary from state to state.  
FOR MORE INFORMATION,  
TELEPHONE 800-836-0655  
NEC SOLUTIONS (AMERICA), INC.  
1250 N. Arlington Heights Road, Suite 400  
Itasca, Illinois 60143-1248  
e. Any other cause which does not relate to a product defect.  
f. Burns or residual images upon the phosphor of the panel.  
4. Cartons, carrying cases, batteries, external cabinets, magnetic  
tapes, or any accessories used in connection with the product.  
5. Service outside of the U.S.A. and Canada.  
WHAT WE WILL PAY FOR AND WHAT WE WILL  
NOT PAY FOR  
We will pay labor and material expenses for covered items,  
but we will not pay for the following:  
1. Removal or installation charges.  
Note: All products returned to NEC Solutions (America),  
Inc. for service MUST have prior approval. To get approval,  
call NEC Solutions (America), Inc. at 800-836-0655.  
2. Costs of initial technical adjustments (set-up), including  
adjustment of user controls. These costs are the  
responsibility of the NEC Solutions dealer from whom the  
product was purchased.  
3. Shipping charges.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NEC Solutions (America), Inc.  
1250 N. Arlington Heights Road, Suite 400  
Itasca, Illinois 60143-1248  
Printed on recycled paper  
Printed in Japan  
7S801441  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Milnor Refrigerator KQEXTT1301 User Manual
Milwaukee Drill 2455 20 User Manual
NEC Webcam NDA 30007 003 User Manual
Nilfisk ALTO Vacuum Cleaner Attix 19AE User Manual
Olympus Camera Lens 261059 User Manual
Omega Speaker Systems Router 1200W Router User Manual
Oreck Vacuum Cleaner BB1000 User Manual
Packard Bell Personal Computer M5850 User Manual
Panasonic Answering Machine KX T1470BA User Manual
Panasonic CD Player CQ DFX88EUC User Manual