Operating and Installation
Instructions
Gas Combiset
CS 1012
®
®
en - US, CA
To prevent accidents and
machine damage,
read the Operating Manual
before
installation or use.
M.-Nr. 07 366 180
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the combiset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Before using the combiset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Fast-Ignition-System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Turning on and off / Regulating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
On/Off indicator and Residual heat indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Cookware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Pan size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Suitable pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ignition safety control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Safety cut-off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Burners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Technical Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cut out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installation of multiple appliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Attach the spring clips and support bars . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Removing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Sealing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Gas pressure regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Nominal ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Converting to another type of gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Help protect our environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Children
WARNING- When using your gas
Children should not be left
unattended in an area where the
~
appliance follow basic
precautions, including the
following:
appliance is in use. Never allow
children to sit or stand on any part of
the appliance.
Caution: Do not store items of interest
to children in cabinets above the
appliance. Children climbing on the
appliance to reach these items could
be injured.
This gas combiset conforms to all
uniform safety codes and
regulations. The manufacturer
cannot be held responsible for
damage or injury caused by
improper use of this appliance.
The appliance is hot during use and
~
remains so for some time after being
switched off. Keep children away from
the appliance.
Read all instructions before
installation or use to prevent
injury and appliance damage.
Keep all pots and pans out of the
~
reach of children. Danger of burning or
scalding.
Keep these operating instructions
in a safe place and pass them on
to any future user.
Ensure that any packing material, is
~
disposed of safely and kept out of the
reach of children. Danger of
suffocation!
SAVE THESE INSTRUCTIONS
Correct usage
Only use the gas combiset for
~
residential cooking, and for the
purposes described in this manual.
Other uses are not permitted and can
be dangerous. The manufacturer will
not be held liable for damage caused
by unauthorized use or improper
operation of any kind.
Persons who lack physical, sensory
~
or mental abilities, or experience with
the appliance should not use it without
supervision or instruction by a
responsible person.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Technical safety
Install the appliance so that the
power cord and gas piping do not
come into contact with any portion of
the combiset which may become hot
during use.
~
Installation, repair and maintenance
~
work should be performed by a Miele
authorized service technician. Work by
unqualified persons could be
dangerous and may void the warranty.
Do not use an extension cord to
~
connect this appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance.
Before installing the combiset,
~
check for externally visible damage.
Do not operate a damaged appliance.
A damaged gas combiset is a hazard.
Do not operate the appliance until it
has been properly installed in the
countertop.
~
Before installation, make sure that
the voltage and frequency listed on the
data plate correspond with the
~
Do not operate any appliance with a
~
household electrical supply. This data
must correspond to prevent injury and
appliance damage. Consult a qualified
electrician if in doubt.
damaged cord or plug, or if the
appliance has been damaged in any
manner. Contact Miele’s Technical
Service Department.
Be certain your appliance is
properly installed and grounded by a
qualified technician.
Defective components should be
~
~
replaced by Miele original spare parts
only. Only with these parts can the
manufacturer guarantee the safety of
the appliance.
To guarantee the electrical safety of
~
this appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician. The manufacturer
will not be held responsible for
Under no circumstance open the
outer casing of the appliance.
~
While the appliance is under
~
warranty repairs should only be
performed by a Miele authorized
service technician. Otherwise the
warranty is void.
damages caused by the lack, or
inadequacy, of an effective grounding
system.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Before servicing, turn off the gas
Safety
~
valve and disconnect the power supply
by either removing the fuse, unplugging
the unit or manually “tripping” the
circuit breaker.
The appliance is hot during use and
remains so for some time after being
~
switched off. Be careful not to touch the
appliance if it may still be hot.
This equipment has not been
~
Protect your hands with oven mitts
or potholders when using the
~
designed for maritime use or for use in
mobile installations such as aircraft or
recreational vehicles. However, under
certain circumstances it may be
possible for installation in these
applications. Please contact the
nearest Miele Dealer or the Miele
Technical Service Department with
specific requirements.
appliance. Use only dry, heat resistant
potholders. Moist or damp potholders
used on hot surfaces can result in
steam burns. Do not let the potholder
touch the hot heating elements. Do not
use towels or other bulky items near the
appliance.
Be sure drafts do not blow
~
After connecting the appliance test
~
for leaks according to the installation
instructions.
flammable material toward the flames
or push the flames so that they extend
beyond the edges of the pan.
If there is any doubt concerning
~
installation contact Miele’s Technical
Service Department.
Be aware of loose fitting or hanging
~
garments when operating the combiset,
they may present a fire hazard.
Do not heat unopened containers.
Built-up pressure may cause the
~
container to burst and result in injury.
,WARNING - NEVER use this
appliance as a space heater to heat
or warm the room. Doing so may
result in carbon monoxide poisoning
and overheating.
Install the combiset in a room that
~
has sufficient ventilation.
This appliance must not be
~
operated outdoors.
Make sure all components of the
~
gas burner is assembled correctly
before using the combiset.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Do not use pans that extend past
the burner grate. Using larger pans
may cause the flames to spread out
and damage the surrounding
countertop or other countertop
appliances.
Always position pan handles and
~
~
utensils inward so they do not extend
over adjacent work areas, burner or the
edge of the combiset.
Do not store items on the appliance
~
when not in use. Items could melt or
catch fire from residual heat or if the
appliance is turned on inadvertently.
For safety and stability, do not use
~
pans with a bottom diameter smaller
than the burner grate.
Never cover the appliance with a
cloth. A fire may result.
~
Only certain types of glass, ceramic
~
or other glazed cookware are suitable
for use on a combiset without breaking
due to the sudden temperature change.
Do not let cooking grease or other
flammable materials accumulate on the
appliance.
~
Do not use containers made of
plastic or aluminum. They may melt at
high temperatures.
~
Do not use a steam cleaner to clean
~
the appliance. Steam could penetrate
electrical components and cause a
short circuit.
The burner grates supplied with the
~
appliance must always be used. Never
place a pan on the burner by itself.
Spills containing salt or sugar
should be removed immediately.
~
Do not use aluminum foil to line any
~
part of the combiset.
Do not leave the combiset
~
unattended while in use. Boil-overs
For proper lighting and performance cause smoking, and greasy spill-overs
of the burner, keep the igniter clean
and dry.
~
may ignite.
Do not use water on grease fires.
Smother any fire or flame, or use a dry
chemical or foam-type extinguisher.
~
Do not heat empty pots or pans,
~
they may be damaged.
For safety reasons the flame should
~
be adjusted to be the same size as the
bottom of the pan or smaller. Do not
Do not flambé under an exhaust
~
hood. Flames could be drawn up into
the hood by the suction or the grease
use small pans with high flame settings filters may ignite.
as the flames can climb the sides of the
If there is a drawer directly
~
underneath the appliance without a
pan.
Ensure that the burner is always
covered with a pan.
wooden base in between, ensure that
no aerosols, combustible liquids or
other easily flammable materials are
kept in it. If cutlery inserts are to be
placed in the drawer, they must be
made of a heat-resistant material.
~
Only use cooking utensils suitable
~
for combiset use.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Make certain that the power cords of
~
small appliances do not come in
contact with the appliance. The
insulation of the cable could become
damaged. Danger of electric shock!
In the event of damage or defect,
~
turn off the appliance immediately. Turn
off the gas shut off valve and
disconnect completely from the
electrical supply. Contact the Miele
Technical Service Department.
Do not use the appliance until it has
been repaired.
Ensure power is not supplied to the
appliance while repair work is carried
out.
Before discarding an old appliance,
~
disconnect it from the gas and
electrical supply, and cut off the power
cord to prevent it from becoming a
hazard.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these
Important Safety instructions.
SAVE THESE INSTRUCTIONS
AND REVIEW THEM
PERIODICALLY
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the combiset
aFast burner
Control knobs:
bNormal burner
cBurner grate
dBurner indicators
eDisplay panel
fRear burner
gFront burner
Indicators
lOn/Off indicator
m"Residual Heat" Indicator
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the combiset
Burner
nBurner cap
oBurner head
pThermocouple
qIgnitor
rBurner base
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using the combiset
Cleaning the combiset
Metal components have a protective
coating which may give off a slight odor
the first time your new appliance is
heated.
Before using for the first time clean the
appliance as follows:
^ Remove any protective foil.
The harmless odor will dissipate after a
short time and does not indicate a
faulty connection or appliance defect.
^ Wash the removable parts of the gas
burner in a mild solution of warm
water and liquid dish soap.
^ Dry and reassemble the parts in the
correct order (see "Cleaning and
care").
^ Wipe down the stainless steel
combiset with a suitable cleaner and
dry thoroughly.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Use
Fast-Ignition-System
The knob must only be turned left to
turn the appliance on and right to
turn it off.
The gas combisets are equipped with a
Fast-Ignition-System which
incorporates the following features:
– The control knob does not need to
be pressed until the flame lights.
If the knob is :
-
turned on without pressing it
down first,
– If the flame goes out because of a
draft, for example, the burner is
automatically re-ignited.
-
-
turned clockwise to turn on, or
turned counterclockwise to turn
the combiset off,
If re-ignition is unsuccessful, the gas
supply is automatically interrupted
(see "Ignition safety control").
parts of the combiset might get
damaged. The manufacturer cannot
be held responsible for these
damages.
Turning on and off / Regulating
The control knob is used to turn on the
burner and to regulate the strength of
the flame.
ß Combiset is turned off
& Highest flame
/ Lowest flame
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Use
Turning on
Turning off
^ Turn the knob clockwise to "ß".
This stops the flow of gas and turns off
the combiset.
On/Off indicator and Residual
heat indicator
^ To turn on the burner, press the
control knob down to pass the
resistance, then release the pressure
and turn it counterclockwise to the
largest flame symbol. The ignitor will
"click" and ignite the gas.
When the combiset is turned on, the
On/Off indicator lights up. Once a
pre-set temperature has been reached,
the residual heat indicator will also light
up. The On/Off indicator goes out when
the combiset is turned off. The residual
heat indicator will remain on until the
combiset is cool enough to touch.
If the burner does not ignite or the
flame goes out, turn the control knob to
"ß". Try again after a few seconds.
If the burner still won't ignite after the
second attempt, turn the control knob
to "ß" and see "Frequently asked
questions".
Do not touch or place any heat
sensitive objects on the combiset
while the residual heat indicator is
on. Danger of damage or injury.
^ Adjust the knob to the desired
setting.
If the display is flashing, a fault has
occurred. See "Frequently asked
questions".
Regulating the burners
^ The burners can be variably adjusted
between the lowest and highest
flame by turning the control knob.
Since the outer portion of the flame is
much hotter than the center, the flame
should be set so that its tips do not
spread beyond the sides of the pan.
Flame tips which extend beyond the
sides of the pan are hazardous.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Cookware
Pan size
Suitable pans
– Set the combiset to a high flame
Any heat resistant pan can be used on
when using a large diameter pan and a gas burner.
low flame when using a small
diameter pan.
Unlike pans used on an electric
combiset, the bases do not need to be
even for good results.
Thick pan bases will give more even
results, hot spots are reduced due to
better heat distribution.
– Generally, wide / shallow pans will
heat up quicker and cook more
evenly than narrow / tall ones.
– Thin pan bases will conduct the heat
faster but not as evenly as thick pan
bases. Stir the food frequently to
prevent burning.
– Using oversized pans may cause the
flames to spread out and damage
the surrounding countertop or other
countertop appliances.
– Whenever possible, keep pots and
pans covered while cooking. This
helps keep in the most possible heat.
– Do not use small pans with high
flame settings, the flame may climb
the sides of the pan.
– Pots with a smaller diameter than the
burner grates and pots that do not sit
securely (without wobbling) are
hazardous and should not be used.
The burner grates supplied with the
appliance must always be used.
Never place a pan on the burner by
itself.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
Ignition safety control
Safety cut-off
This appliance is equipped with an If a zone has been on for an unusually
Ignition Safety Control. This control cuts long period of time (approx. 4 hours), it
the gas supply if the flame goes out
and reignition is unsuccessful.
will automatically shut off.
^ To reignite the burner, turn the
control knob to “ß”, then switch the
burner on as usual.
^ To reignite the burner, turn the
control knob to “ß”, then switch the
burner on as usual.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Combiset
Never use a steam cleaner to clean
this combiset. Pressurized steam
could cause permanent damage to
the surface and to components for
which the manufacturer cannot
accept responsibility.
Let the appliance cool to a safe
temperature before removing the
grates.
^ Clean the grates, combiset and
knobs with a sponge and a mild
solution of warm water and liquid
dish soap.
Do not use any sharp or pointed
objects which could damage the
seal between the frame and the
countertop.
^ Soak baked or hardened spills.
Dry the combiset and grates
thoroughly after cleaning.
The stainless steel surfaces can be
cleaned using a non-abrasive stainless
steel cleaner.
To help prevent resoiling, a conditioner
for stainless steel can also be used.
Apply sparingly with even pressure.
These cleaning products are available
from Miele.
Never use scouring agents, pads,
abrasive cleaning agents, or strong
cleaners, e.g. oven sprays, stain or
rust removers, these could damage
the surface of the appliance.
Keep the ignitor in the burner dry. If
it gets wet it will not spark.
Do not use stainless steel cleaner on
or around the printing, it may rub
off. Use only a soft sponge with
some dish liquid and warm water to
clean this area.
Dry your combiset thoroughly after
cleaning it to prevent lime deposits.
Spills containing salt or sugar should
be cleaned immediately.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Burners
Reassembling the burner
The burner can be dismantled and
cleaned when cool.
^ Remove the burner parts and wash
them in a solution of warm water and
liquid dish soap. Dry them
thoroughly. Make sure that the flame
holes are clean and completely dry.
^ Wipe the burner base clean with a
damp cloth and then dry.
^ Gently wipe the ignitor and ignition
safety control with a slightly damp
cloth, and then wipe dry.
Make sure that no liquid gets into
the appliance.
^ Place the burner head o onto the
burner base r, making sure that the
thermocouple p and the ignitor q
align through the holes in the burner
head. The burner head must fit into
place properly.
^ Place the burner cap n evenly onto
the burner head o.
Once the burner cap is in the right
position, it will not move.
Be careful not to mix up the parts.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
,Repairs should only be carries out by an authorized technician in
accordance with local and national safety regulations. Unauthorized repairs
could cause injury or appliance damage. The manufacturer cannot be held
responsible for unauthorized work.
The burner does not ignite when the combiset is being used for the first
time or after an extended period of not being used.
Possible fault
Solution
There could be air in the gas pipe.
You may need to make several
attempts before the burner ignites
successfully.
The On/Off and residual heat indicators are flashing.
Possible fault
Solution
There has been a power failure.
Turn all the controls clockwise to "ß".
You can now operate the appliance as
normal.
The On/Off indicator is flashing.
Possible fault
Solution
The gas supply has been cut-off.
– Turn all the controls clockwise to
position "ß". You can now operate the
appliance as normal.
– If the problem persists, disconnect
the appliance from the electrical
supply for a few seconds.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
The burner does not ignite after several attempts.
Possible fault Solution
Disconnect the appliance from the electrical supply for a few seconds. If the
problem persists, check if:
– The burner is assembled incorrectly. – Reassemble the burner as shown in
"Cleaning and Care - Burners".
– The gas valve is closed.
– Open the gas valve.
– The burner is wet and soiled.
– Clean the burners. See "Cleaning
and Care".
– The flame slits are dry and
unblocked
– Dry the igniters.
The flame goes out after being lit.
Possible fault
Solution
The flames are not touching the ignition safety control. Check if:
– The burner is assembled incorrectly. – Reassemble the burner as shown in
"Cleaning and Care - Burners".
– There is no soiling on the ignition
safety control.
– See "Cleaning and Care".
The flame appears different than usual.
Possible fault
Solution
The burner is assembled incorrectly.
Reassemble the burner as shown in
"Cleaning and Care - Burners".
The flame goes out during operation.
Possible fault
Solution
The burner is assembled incorrectly.
Reassemble the burner as shown in
"Cleaning and Care - Burners".
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
The igniter does not spark.
Possible fault
Solution
The circuit breaker has tripped.
Re-set the circuit breaker. Contact an
electrician for assistance if in doubt.
Food has deposited itself between the See "Cleaning and care".
ignitor and the burner cap.
Food has deposited on the ignition
safety control.
See "Cleaning and care".
For safety reasons, after a spill on the combiset you may need to wait approx. 5
minutes before you are able to reignite the burner. Wait 5 minutes and ignite the
burner as usual.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Service
In the event of a fault which you cannot MieleCare
easily fix yourself, please contact the
(USA only)
Miele Technical Service Department at
the address on the back of this booklet. MieleCare, our Extended Service
Contract program; gives you the
When contacting Technical Service
assurance of knowing that your
please quote the serial number and
appliance investment is covered by 5
model of the appliance. This
years of worry free ownership.
information is visible on the silver data
MieleCare is the only Extended Service
plate supplied with the appliance.
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability and
longevity of your Miele appliance.
Please note that unless expressly
approved in writing by the Miele
Service department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
21
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE
To prevent accidents
and machine damage
read these instructions
before
installation or use.
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Installation
Deep fat fryers must not be installed
~
directly next to gas combisets. Gas
The minimum distances given in
these Installation instructions are to
combustible surfaces, and must be
observed to ensure safe operation.
Failure to do so increases the risk of
fire.
flames can ignite splattering oil. A
distance of at least 11 5/16"" (288 mm)
should be maintained between these
two appliances.
Install the appliance so that the
~
power cord or gas piping does not
come into contact with any portion of
the combiset which may become hot
during use.
The cabinetry and venting hood
should be installed first to prevent
damage to the combiset.
This appliance must be installed
with its own shut off valve and the
included gas pressure regulator.
Both the valve and the regulator
must be easily accessible to the
consumer after the appliance is
installed.
Gas appliances should only be
installed in a well ventilated area.
~
The countertop must be bonded
~
with heat resistant (212 °F/100 °C)
adhesive to prevent distortion or
dissolving.
This appliance has not been
~
This appliance must be
designed for maritime use or for use in
mobile installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the Miele Technical Service
Department with specific requirements.
disconnected from the gas supply
during any pressure testing of the
system performed in excess of ½ psi
(3.5 kPa). This appliance must be
isolated at test pressures equal to or
less than ½ psi (3.5 kPa).
The combiset must not be installed
Any pipe connections must be made
using a thread sealant approved for
gas connections. Failure to correctly
install these items could lead to a
gas leak and subsequent explosion.
~
over a dishwasher, washer, dryer,
refrigerator or freezer. Heat radiated by
the combiset may damage the
appliances.
Keep this instruction book in a safe
place for reference and pass it on to
any future user.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Safety distances above the
appliance
The minimum safety distance given by
the hood manufacturer must be
maintained between the combiset and
the hood above it. See the installation
instructions of the hood for these safety
measurements.
If the hood manufacturers instructions
are not available or if flammable objects
are installed over the combiset (e.g.
cabinets, utensil rail, etc.), a minimum
safety distance of 30" (760 mm) must
be maintained.
If there is more than one appliance
beneath a hood (e.g. wok burner
and electric combiset), and they
have different minimum safety
distances always observe the
greater distance.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Safety distances to the sides
of the appliance
The appliance should only be installed
as shown in the illustrations, while
maintaining the required safety
distances shown. Do not install the
appliance between two tall cabinets,
this is a fire hazard.
(50 mm)
2 "
A distance of at least 2" (50 mm) must
be kept between the countertop cut-out
recommended
and the rear wall because of the high
temperatures radiated.
The minimum distance required from
the countertop cut-out to the side wall
a:
2"
(50mm)
2" (50 mm)
for CS 1112
CS 1122
CS 1212
CS 1221
CS 1223
CS 1326
CS 1411
1
not recommended
6" (150 mm)
for CS 1312
CS 1322
CS 1421
10" (250 mm)
for CS 1011
CS 1012
CS 1028
not allowed
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Safety distance when installing the appliance near a wall with trim or a back
splash
A minimum distance of 2" (50 mm) between the trim or back splash and the
countertop cut-out if required.
This distance is only necessary if these items are made of combustible materials
e.g. wood. If the trim or back splash is made of a non-combustible material, the
required safety distance can be reduced by the thickness of the wall covering
material.
aWall frame
bSheet rock or wall board
cTrim or back splash
dCountertop
eCountertop cut-out
f2" (50 mm) minimum clearance
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation dimensions
aSpring clips
bAppliance front
cInstallation height
dPower supply box with connection cable, L = 78 3/4" (2000 mm)
eGas fitting
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Cut out
If during installation the seal around the
frame does not sit flush with the
countertop in the corners, the corner
radius, maximum 3/16" (4 mm), can be
carefully filed down to fit.
^ Make the countertop cut-out for the
desired number of appliances.
Remember to maintain a minimum
safety distance from the back wall,
as well as from any tall unit or side
wall to the left or right of the
combiset.
See also the "IMPORTANT SAFETY
INSTRUCTIONS".
^ Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture.
The materials used must be heat
resistant.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation of multiple
appliances
When installing more than one combiset appliance, a support bar b must be
installed between the appliances.
Countertop cut-out
two appliances
Countertop cut-out
three appliances
19mm)
19mm)
D
(500
(500
11/16"
11/16"
D
+
+
-
-
1
1
b
b
C
C
B
A
A
For the installation of three appliances
the width of the countertop cut-out D is
the sum of A and B and C.
For the installation of two appliances
the width of the countertop cut-out D is
the sum of A and C.
A, B and C = appliance widths
11 5/16", 15" or 22 11/16"
(288 mm, 380 mm or 576 mm)
minus 5/16" (8 mm) to allow for the
overhang
If more than three appliances are
being installed, you will need to add,
A, B or C for each additional
appliance.
D = width of the countertop cut-out
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Sample calculations for a countertop cut-out for three appliances
A
appliance width appliance width
minus 5/16"
(8 mm)
B
C
D
appliance width
minus 5/16"
(8 mm)
Countertop
cut-out
11" (280 mm)
11" (280 mm)
11 5/16" (288 mm)
15" (380 mm)
11" (280 mm)
33 5/16" (848 mm)
40 5/8" (1032 mm)
14 5/8" (372 mm)
11" (280 mm) 22 11/16" (576 mm) 22 3/8" (568 mm) 56 1/16" (1424 mm)
14 5/8" (372 mm) 11 5/16" (288 mm)
14 5/8" (372 mm) 15" (380 mm)
11" (280 mm)
37" (940 mm)
14 5/8" (372 mm)
44 1/4" (1124 mm)
14 5/8" (372 mm) 22 11/16" (576 mm) 22 3/8' (568 mm) 59 11/16" (1516 mm)
22 3/8" (568 mm) 11 5/16" (288 mm)
11" (280 mm)
14 5/8" (372 mm)
22 3/8" (568 mm)
44 3/4" (1136 mm)
52" (1320 mm)
22 3/8" (568 mm)
22 3/8" (568 mm)
15" (380 mm)
-
44 3/4" (1136 mm)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
3/16"
1"-1
(25-30mm)
D
2"
2"
(50mm)(50mm)
19
(500 mm)
11/16"
2"
2"
3/16"
1"-1
+
-
1
(50mm)(50mm)
(25-30mm)
a
a
b
c
a
a
c
a
a
C
5/8"
3/8"
22
B
11"/14
/
(280/372/568mm)
11/16"
A
5/8"
3/8"
22
22
115/16"/15"/
11("2/801/4372/568mm)
/
(288/380/576mm)
aSpring clips
bSupport bars
cSpace between support bar and countertop
An additional support bar is required for each additional appliance. The position
for attachment of an additional spacing strip depends on the width of the
appliance B.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Attach the spring clips and
support bars
Wood or solid surface countertops
Granite countertop
3/16"
3/16"
1"-1
1"-1
(25-30mm)
(25-30mm)
c
a
a
c
b
b
^ Place the supplied spring clips a
and the support bars b at the
marked positions as shown above,
by laying them on the upper edge of
the cut-out and then securing them
with the 1/8" x 1" (3.5 x 25 mm) screws
(supplied).
^ Position and attach the spring clips
a and support bars b with strong,
double-sided tape c.
The screws are not needed for granite
countertops.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
a
^ Coat the edges of the spring clips,
d
b
^ and the space d between the strips
and the countertop with silicone
(supplied).
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing the appliance
Removing the appliance
^ Feed the power cord down through
the cut-out.
If the appliance is accessible from
below, it can be pushed up and out of
the cut-out. Push up from the back first.
^ Then place the front side of the
appliance in the countertop cut-out.
If the appliance is not accessible from
below, grip the appliance with both
hands at the back, pull forward, then lift
it up and out.
^ Then with a hand on each side of the
appliance press down evenly on the
edges until it clicks into position.
When doing so make sure that the
appliance seal sits tightly on the
countertop to ensure it is sealed
correctly. Do not permanently seal
into the countertop.
^ Connect the appliance to the main
power supply.
^ Turn the appliance on and check the
function.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Sealing
The appliance must not be permanently
sealed into the countertop when
installed. The sealing strip under the
edge of the appliance provides a
sufficient seal for the countertop.
If the appliance is sealed into
position, the countertop or appliance
could be damaged if it needs to be
removed for maintenance or service.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
This appliance must be grounded
according to local or national codes.
This appliance is equipped with a
three-prong grounding plug to
prevent shock hazards. It should be
plugged directly into a properly
grounded outlet. Do not cut or
remove the grounding prong from
the plug. If the plug does not fit the
outlet, have the proper outlet
All electrical work should be
performed by a qualified electrician
in accordance with local codes and
with the:
-
National Electrical Code
ANSI / NFPA No. 70
for the USA
installed by a licensed electrician.
or
-
To guarantee the electrical safety of
this appliance, continuity must exist
between the appliance and an
effective grounding system. It is
imperative that this basic safety
requirement be met. If there is any
doubt, have the electrical system of
the house checked by a qualified
electrician.
The manufacturer cannot be held
responsible for damages caused by
the lack, or inadequacy, of an
effective grounding system.
Canadian Electrical Code Part I
for Canada
(CSA Standard C 22.1).
,WARNING
Disconnect the appliance from the
main power supply before
installation or service. To reduce the
risk of electric shock, make sure that
the appliance is properly grounded
after installation.
Power supply
Note to the installer
The automatic ignition requires that the
combiset be connected to a 120 VAC,
60 Hz power supply. The supply line
should be protected by a 15 A fuse.
Please leave these instructions with the
consumer or the appliance.
Actual power consumption (during
ignition only) is 25 W.
This appliance is equipped with a
78 3/4" (2000 mm) long power cord that
is ready for connection to the
appropriate outlet.
Place the power outlet so that it is
accessible after the appliance has
been installed in the countertop.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Wiring Diagram
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas connection
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
The gas connection must be made
in accordance with local codes or, in
the absence of local codes, with
In Massachusetts a licensed
plumber/gas fitter is required.
-
the National Fuel Gas Code,
ANSI Z 223.1/NFPA 54
for the USA
This appliance must be installed
with its own shut off valve and the
included gas pressure regulator.
Both the valve and the regulator
must be easily accessible to the
consumer to turn on or shut off the
gas supply after the appliance is
installed.
or
-
the current Can/CGA B 149.1
and .2 Installation Codes for gas
burning appliances for Canada.
Make sure that the maximum gas
supply pressure before the gas
pressure regulator is never more than
½ psi for both natural gas or LP gas.
This appliance and its individual
shut off valve must be disconnected
from the gas supply during any
pressure testing performed in
excess of ½ psi (3.5 kPa), or
isolated from the gas line by closing
its individual manual shut off valve at
test pressures equal to or less than
½ psi (3.5 kPa).
The minimum supply pressure to get
the required gas input is
4" w.c. for natural gas:
10" w.c. for LP gas.
Any pipe connections must be made
using a thread sealant approved for
gas connections. Failure to correctly
install these items could lead to a
gas leak and subsequent explosion.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas connection
Gas pressure regulator
For convenience, an AGA or CGA
approved flexible stainless steel gas
hose (accordion type) may be used
between the gas connection and the
regulator. This will allow the appliance
to be lifted out of the countertop for
cleaning or servicing. Make sure that
any drawers, cabinet doors, etc., do not
rub on this gas hose.
A pressure regulator that is convertible
from natural to LP gas (Propane) or vice
versa is included with the appliance.
The included regulator corresponds
with the gas type of the combiset. Verify
before installing.
The adjusted pressure is:
natural gas - 4" w.c.
LP gas - 10" w.c.
Do not use any regulator unless it
has been supplied by Miele. Doing
so may cause a gas leak.
If there is any doubt concerning
installation contact the Miele Technical
Service Department.
After connecting the appliance check
all fittings for gas leaks e.g. with
soapy water.
When installed properly, the flame will
be steady and quiet. It will also have a
sharp, blue inner core that will vary in
length proportional to the burner size.
Flame adjustment will not be
aCombiset
b½" NPT
necessary.
cRegulator
As shown in the above diagram, the
included regulator must be used when
connecting the Miele combiset to your
gas supply. This item has been
customized by Miele to meet all
applicable safety requirements. Make
sure the regulator is easily accessible
for adjustment after the appliance has
been installed.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas connection
Nominal ratings
Maximum output
Gas type
BTU/hr
kW
Normal burner
Fast burner
Total output
Natural Gas (NG)
Propane (LP)
5,700
5,000
1.65
1.45
Natural Gas (NG)
Propane (LP)
10,600
9,300
3.10
2.75
Natural Gas (NG)
Propane (LP)
16,300
14,300
4.75
4.2
Minimum output
Gas type
BTU/hr
kW
Normal burner
Fast burner
Natural Gas (NG)
Propane (LP)
775
0.227
0.296
1,010
Natural Gas (NG)
Propane (LP)
1,550
1,500
0.454
0.439
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Converting to another type of gas
The combiset should have been
ordered for connection to either natural
gas or LP gas (propane).
If the combiset is not configured for the
proper type of gas connection please
contact your Miele Dealer.
If the appliance is to be connected to a
type of gas other than it was originally
configured for, both the regulator and
burner must be converted. A
conversion kit is available as an
optional accessory from the Miele
Technical Service Department.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Help protect our environment
Disposal of packing materials
Disposal of an old appliance
The cardboard box and packing
materials are biodegradable and
recyclable. Please recycle.
Old appliances contain materials that
can be recycled. Please contact your
local recycling authority about the
possibility of recycling these materials.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
Danger of suffocation!
Before discarding an old appliance
disconnect it from the electrical supply
and cut off the power cord to prevent it
from becoming a hazard.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / 2508
M.-Nr. 07 366 180 / 00
For the most updated manual see the Miele web site.
Download from Www.Somanuals.com. All Manuals Search And Download.
|