MDG30PNH / MDG30MNV
Installation Manual
30 lb Single Pocket / Phase 7 / Non-Coin
with Fire Suppression System
AVERTISSEMENT:Assurez-vous de bien
suivre les instructions données dans cette
notice pour réduire au minimum le risque
d’incendie ou d’explosion ou pour éviter
tout dommage matériel, toute blessure ou
la mort.
WARNING: For your safety the information
in this manual must be followed to
minimize the risk of fire or explosion and
to prevent property damage, personal
injury or death.
— Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
—Ne pas entreposer ni utiliser d’essence
ni d’autres vapeurs ou liquides
inflammables à proximité de cet
appareil ou de tout autre appareil.
— WHATTO DO IF YOU SMELL GAS:
—QUE FAIRE SI VOUS SENTEZ UNE
ODEUR DE GAZ:
G
Do not try to light any appliance.
Do not touch any electrical switch;
do not use any phone in your
building.
Clear the room, building or area of
all occupants.
Immediately call your gas supplier
from a neighbor’s phone. Follow
the gas supplier’s instructions.
If you cannot reach your gas
G
G
Ne pas tenter d’allumer d’appareils.
Ne touchez à aucun interrupteur. Ne
G
pas vous servir des téléphones se
G
trouvant dans le bâtiment.
Évacuez la pièce, le bâtiment ou la
G
G
zone.
G
Appelez immédiatement votre
fournisseur de gaz depuis un voisin.
Suivez les instructions du fournisseur.
Si vous ne pouvez rejoindre le
G
supplier, call the fire department.
G
fournisseur de gaz, appelez le service
des incendies.
— Installation and service must be
performed by a qualified installer, service
agency or the gas supplier.
—L’installation et l’entretien doivent être
assurés par un installateur ou un
service d’entretien qualifié ou par le
fournisseur de gaz.
RETAIN THESE
INSTRUCTIONS INA
SAFE PLACE FOR
FUTURE REFERENCE
Part No. 113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
YOU MUSTDISCONNECTAND LOCKOUTTHE ELECTRIC SUPPLYANDTHE GAS
SUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR GUARDS ARE
REMOVED FROM THE MACHINE TO ALLOW ACCESS FOR CLEANING,
ADJUSTING, INSTALLATION, OR TESTING OF ANY EQUIPMENT PER OSHA
(Occupational Safety and HealthAdministration) STANDARDS.
“Caution: Label all wires prior to
disconnection when servicing
controls. Wiring errors can cause
improper operation.”
«Attention:Au moment de l’entretien des commandes,
étiquetez tous les fils avant de les débrancher. Des
erreurs de câblage peuvent entraîner un fonctionnement
inadéquat et dangereux.»
CAUTION
DRYERS SHOULD NEVER BE LEFT UNATTENDEDWHILE IN OPERATION.
WARNING
CHILDREN SHOULD NOTBEALLOWED TO PLAYON OR NEAR THE DRYER(S).
CHILDREN SHOULD BE SUPERVISED IFNEAR DRYERS IN OPERATION.
FORYOUR SAFETY
DO NOT DRYMOPHEADS INTHE DRYER.
DO NOT USE DRYER INTHE PRESENCE OF DRYCLEANING FUMES.
WARNING
UNDER NO CIRCUMSTANCES should the dryer door switch, lint door switch, or
heat safety circuit ever be disabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
The dryer must never be operated with any of the back guards, outer tops, or service
panels removed. PERSONALINJURYOR FIRE COULD RESULT.
WARNING
DRYER MUST NEVER BE OPERATED WITHOUTTHE LINT FILTER/SCREEN IN
PLACE, EVEN IFAN EXTERNALLINT COLLECTION SYSTEM IS USED.
IMPORTANT
PLEASE OBSERVEALLSAFETYPRECAUTIONS displayed on the equipment and/or
specified in the installation manual included with the dryer.
Dryer must not be installed or stored in an area where it will be exposed to water or weather.
The wiring diagram for the dryer is located in the front electrical control box area.
IMPORTANT
Dryer must be installed in a location/environment, which the ambient temperature
remains between 40° F (4.44° C) and 130° F (54.44° C).
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
SECTION I
SAFETYPRECAUTIONS ........................................................................................................2
SECTION II
SPECIFICATIONS ..................................................................................................................4
SECTION III
INSTALLATIONPROCEDURES ...........................................................................................6
A. Unpacking/Setting Up............................................................................................................................. 6
B. Location Requirements........................................................................................................................... 6
C. Dryer Enclosure Requirements .............................................................................................................. 7
D. FreshAir Supply Requirements .............................................................................................................. 8
E. Exhaust Requirements ............................................................................................................................ 9
F. Electrical Information ........................................................................................................................... 12
G. Gas Information .................................................................................................................................... 15
H. Preparation for Operation/Start-Up...................................................................................................... 18
I. Preoperational Tests ............................................................................................................................. 19
J. Preoperational Instructions ................................................................................................................... 20
K. Shutdown Instructions .......................................................................................................................... 21
SECTIONIV
SERVICE/PARTSINFORMATION ......................................................................................22
A. Service .................................................................................................................................................. 22
B. Parts...................................................................................................................................................... 22
SECTIONV
WARRANTYINFORMATION ..............................................................................................23
A. Returning Warranty Cards ................................................................................................................... 23
B. Warranty ............................................................................................................................................... 23
SECTIONVI
ROUTINEMAINTENANCE .................................................................................................24
A. Cleaning ................................................................................................................................................ 24
B. Adjustments .......................................................................................................................................... 25
C. Lubrication ............................................................................................................................................ 25
SECTIONVII
DATALABELINFORMATION ............................................................................................26
SECTIONVIII
PROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENT COMPONENTS .....27
SECTION IX
FIRE SUPPRESSION SYSTEM............................................................................................29
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION I
SAFETY PRECAUTIONS
WARNING: For your safety, the information in this manual must be followed to minimize the risk of
fire or explosion or to prevent property damage, personal injury, or loss of life.
WARNING: The dryer must never be operated with any of the back guards, outer tops, or
service panels removed. PERSONALINJURYOR FIRE COULD RESULT.
1. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
2. Purchaser and user should consult the local gas supplier for proper instructions to be followed in the event
the user smells gas. The instructions should be posted in a prominent location.
3. WHAT TO DO IF YOU SMELL GAS:
a. DO NOT try to light any appliance.
b. DO NOT touch any electrical switch.
c. DO NOT use any phone in your building.
d. Clear the room, building, or area of ALL occupants.
e. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
f. If you cannot reach your gas supplier, call the fire department.
4. Installation and service must be performed by a qualified installer, service agency, or gas supplier.
5. Dryers must be exhausted to the outdoors.
6. Although Maytag produces a very versatile dryer, there are some articles that, due to fabric composition or
cleaning method, should not be dried in it.
WARNING: Dry only water washed fabrics. DO NOT dry articles spotted or washed in dry
cleaning solvents, a combustible detergent, or “all purpose” cleaner.
EXPLOSION COULD RESULT.
WARNING: DO NOT dry rags or articles coated or contaminated with gasoline, kerosene, oil, paint,
or wax. EXPLOSION COULD RESULT.
IMPORTANT: Dryer must be installed in a location/environment, which the ambient
temperature remains between 40° F (4.44° C) and 130° F (54.44° C).
WARNING: DO NOT dry mop heads. Contamination by wax or flammable solvents will create a
fire hazard.
2
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, or
similarly textured rubber materials. Drying in a heated basket (tumbler) may damage
plastics or rubber and may be a fire hazard.
7. A program should be established for the inspection and cleaning of lint in the burner area, exhaust ductwork,
and area around the back of the dryer. The frequency of inspection and cleaning can best be determined
from experience at each location.
WARNING: The collection of lint in the burner area and exhaust ductwork can create a potential fire
hazard.
8. For personal safety, the dryer must be electrically grounded in accordance with local codes and/or the
National Electrical Code ANSI/NFPA NO. 70-LATEST EDITION or in Canada, the Canadian Electrical
Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.
NOTE: Failure to electrically ground the dryer properly will VOID THEWARRANTY.
9. UNDER NO CIRCUMSTANCES should the dryer door switch, lint door/drawer switch, or heat safety
circuit ever be disabled.
WARNING: PERSONALINJURYOR FIRE COULD RESULT SHOULD THE DRYER
DOOR SWITCH, LINT DOOR/DRAWER SWITCH, OR HEAT SAFETY
CIRCUIT EVER BE DISABLED.
10. This dryer is not to be used in the presence of dry cleaning solvents or fumes.
11. Remove articles from the dryer as soon as the drying cycle has been completed.
WARNING: Articles left in the dryer after the drying and cooling cycles have been completed can
create a fire hazard.
12. READ AND FOLLOW ALL CAUTION AND DIRECTION LABELS ATTACHED TO THE
DRYER.
13. For safety, proper operation, and optimum performance, the dryer must not be operated with a load less
than sixty-six percent (66%) 20 lb (9.07 kg) of its rated capacity.
WARNING: YOU MUST DISCONNECTAND LOCKOUT THE ELECTRIC SUPPLYAND
THE GAS SUPPLYOR THE STEAM SUPPLYBEFOREANYCOVERS OR
GUARDSARE REMOVED FROM THE MACHINE TOALLOWACCESS
FOR CLEANING,ADJUSTING, INSTALLATION, OR TESTINGOFANY
EQUIPMENTPER OSHA (Occupational Safety and HealthAdministration)
STANDARDS.
113307-7
Maytag Co.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION II
SPECIFICATIONS
13.6 kg
83.2 cm
MAXIMUM CAPACITY (DRY WEIGHT)
30 lbs
32-3/4”
25-5/8”
1/2 hp
BASKET (TUMBLER) DIAMETER
BASKET (TUMBLER) DEPTH
BASKET (TUMBLER) MOTOR
DOOR OPENING (DIAMETER)
BASKET (TUMBLER) VOLUME
DRYERS PER 20’/40’ CONTAINER
DRYERS PER 45’/48’ TRUCK
S.A.F.E. WATER CONNECTION
VOLTAGE AVAILABLE
65.1 cm
0.373 kW
54.61 cm
0.354 cu m
21-1/2”
12.5 cu ft
12/26
30/32
3/4” - 11.5 NH
120v 1ø 2w 60 Hz
242 kg
APPROX. WEIGHT (UNCRATED)
APPROX. WEIGHT (CRATED)
HEAT INPUT
534 lbs
571 lbs
259 kg
25,200 kcal/hr
13 cmm
100,000 Btu/hr
460 cfm
AIRFLOW
INLET PIPE CONNECTION
1/2” F.N.P.T.*
Shaded areas are stated in metric equivalents
12/1/03
*
Size of piping to dryer varies with installation conditions. Contact factory for assistance.
NOTE: The manufacturer reserves the right to make changes in specifications at any time without
notice or obligation.
4
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
NOTE: The manufacturer reserves the right to make changes in specifications at any time without
notice or obligation.
113307-7
Maytag Co.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION III
INSTALLATION PROCEDURES
Installation should be performed by competent technicians in accordance with local and state codes. In the
absence of these codes, the installation must conform to applicableAmerican National Standards:ANSI Z223.1-
LATEST EDITION (National Fuel Gas Code) or ANSI/NFPA NO. 70-LATEST EDITION (National Electrical
Code) or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-M91
(Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST EDITION (for General
Installation and Gas Plumbing) or Canadian Electrical Codes Parts 1 & 2 CSAC22.1-1990 or LATEST EDITION
(for Electrical Connections).
A. UNPACKING/SETTING UP
Remove protective shipping material (i.e., plastic wrap and optional shipping box) from dryer.
IMPORTANT: Dryer must be transported and handled in an upright position at ALL times.
The dryer can be moved to its final location while still attached to the skid or with the skid removed. To unskid
the dryer, locate and remove the four (4) bolts securing the base of the dryer to the wooden skid. Two (2) are
at the rear base (remove the back panel for access), and two (2) are located in the bottom of the lint chamber.
To remove the two (2) bolts located in the lint chamber area, remove the lint door/drawer.
With the skid removed, to make it easier to slide the dryer into its final position, slightly lower ALL four (4)
leveling legs, so that the dryer will slide on the legs instead of the base frame.
Leveling Dryer
The dryer is equipped with four (4) leveling legs, one (1) at each corner of the base. Two (2) are located at the
rear of the dryer base, and two (2) are located in the lint chamber (coop). To increase bearing life and improve
efficiency, the dryer should be tilted slightly to the rear.
B. LOCATION REQUIREMENTS
Before installing the dryer, be sure the location conforms to local codes and ordinances. In the absence of such
codes or ordinances the location must conform with the National Fuel Gas Code ANSI.Z223.1 LATEST
EDITION, or in Canada, the installation must conform to applicable Canadian Standards: CAN/CGA-B149.1-
M91 (Natural Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION (for General Installation and
Gas Plumbing).
1. The dryer must be installed on a sound level floor capable of supporting its weight. Carpeting must be
removed from the floor area that the dryer is to rest on.
IMPORTANT: “The dryer must be installed on noncombustible floors only.”
2. The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.
3. The dryer is for use in noncombustible locations.
6
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Provisions for adequate air supply must be provided as noted in this manual (refer to Fresh Air Supply
Requirements in Section D).
5. Clearance provisions must be made from combustible construction as noted in this manual (refer to Dryer
Enclosure Requirements in Section C).
6. Provisions must be made for adequate clearances for servicing and for operation as noted in this manual
(refer to Dryer Enclosure Requirements in Section C).
7. The dryer must be installed with a proper exhaust duct connection to the outside as noted in this manual
(refer to Exhaust Requirements in Section E).
8. Dryer must be located in an area where correct exhaust venting can be achieved as noted in this manual
(refer to Exhaust Requirements in Section E).
IMPORTANT: Dryer should be located where a minimum amount of exhaust duct will be necessary.
9. The dryer must be installed with adequate clearance for air openings into the combustion chamber.
CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors. Every 6
months, inspect the exhaust ducting and remove any lint buildup.
IMPORTANT: Dryer must be installed in a location/environment, which the ambient
temperature remains between 40° F (4.44° C) and 130° F (54.44° C).
C. DRYER ENCLOSURE REQUIREMENTS
Bulkheads and partitions should be made of noncombustible materials and must be located a minimum of
12-inches (30.48 cm) above the dryer’s outer top; except along the front of the dryer, which may be closed if
desired.
NOTE: Allowances must be made for opening the control door.
NOTE: With the exception of the floor, clearances shown are for combustible construction.
X = 12-inch (30.48 cm) minimum, 24-inches (60.96 cm) is suggested for ease of maintenance.
*
Not applicable.
** A minimum of 12-inches (30.48 cm) above the dryer’s outer top; except along the front of the dryer, which may be closed if desired.
113307-7
Maytag Co.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: Air considerations are important for proper and efficient operation.
Dryers may be positioned sidewall to sidewall. However, a 1/16” (1.59 mm) minimum allowance must be made
for opening and closing of the control door. It is suggested that the dryer be positioned about 2 feet (0.61 meters)
away from the nearest obstruction for ease of installation, maintenance, and service (to be measured from the
back guard). Refer to the illustration on the previous page for details.
D. FRESH AIR SUPPLY REQUIREMENTS
The dryer must be installed with provisions for adequate combustion and make-up air supply. As a general rule,
an unrestricted air entrance from the outdoors (atmosphere) of 1 square foot (0.09 square meters) is required for
each dryer (based on 1 square inch per 1,000 Btu [251.9958 kcal]). If registers or louvers are installed over the
openings, then the area must be increased. It is not necessary to have separate make-up air openings for each
dryer. Common make-up air openings are acceptable. However, they must be set up in such a manner that the
make-up air is distributed equally to the dryers.
EXAMPLE: For a bank of four (4) dryers, two (2) unrestricted openings measuring 12-inches by 18-inches
(30.48 cm by 45.72 cm) are acceptable. (Based on 1 inch2 [6.4516 cm2] per 1,000 Btu [251.9958
kcal].)
A = 12-inches (30.48 cm)
B = 18-inches (45.72 cm)
IMPORTANT: Make-up air openings should not be located in an area directly near where exhaust
vents exit the building.
Allowances must be made for remote or constricting passageways or where dryers are located at excessive
altitudes or predominantly low pressure areas.
IMPORTANT: Make-up air must be provided from a source free of contaminating fumes such as dry
cleaning solvent fumes. Make-up air that is contaminated by dry cleaning solvent
fumes will result in irreparable damage to the motors and other dryer components.
NOTE: Component failure due to dry cleaning solvent fumes willVOIDTHEWARRANTY.
8
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
E. EXHAUST REQUIREMENTS
Exhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwork will
create excessive back pressure which results in slow drying, increased use of energy, and shutdown of the
burner by the airflow (sail) switch, burner hi-limits, or lint chamber hi-limit protector thermostat. The dryer must
be installed with a proper exhaust duct connection to the outside.
When possible, it is suggested to provide a separate (single) exhaust duct for each dryer.
CAUTION: This dryer produces combustible lint and must be exhausted to the outdoors.
CAUTION: IMPROPERLY SIZED OR INSTALLED EXHAUST DUCTWORK CAN
CREATE APOTENTIAL FIRE HAZARD.
The exhaust ductwork should be laid out in such a way that the ductwork travels as directly as possible to the
outdoors with as few turns as possible. The shape of the ductwork is not critical provided that the minimum
cross section area is maintained. Single or independent dryer venting is recommended.
It is suggested that the use of 90° turns be avoided; use 30° or 45° angles instead.
The ductwork should be smooth inside with no projections from sheet metal screws or other obstructions,
which will collect lint. When adding ducts, the ducts to be added should overlap the duct to which it is connected.
ALL ductwork joints must be taped to prevent moisture and lint from escaping into the building. Additionally,
inspection doors should be installed at strategic points in the exhaust ductwork for periodic inspection and
cleaning.
IMPORTANT: When connecting ductwork to the dryer exhaust duct, be sure that when screws are
used they DO NOT restrict the operation (both opening and closing) of the damper.
NOTE: When the exhaust ductwork passes through a wall, ceiling, or roof made of combustible
materials, the opening must be 2-inches (5.08 cm) larger than the duct (all the way around).
The duct must be centered within this opening.
To protect the outside end of the horizontal ductwork from the weather, a 90° elbow bent downward should be
installed where the exhaust exits the building. If the ductwork travels vertically up through the roof, it should be
protected from the weather by using a 180° turn to point the opening downward. In either case, allow at least
twice the diameter of the duct between the duct opening and the nearest obstruction (i.e., roof or ground level).
IMPORTANT: DO NOT use screens, louvers, or caps on the outside opening of the exhaust
ductwork.
IMPORTANT: Exhaust back pressure measured by a manometer at the dryer exhaust duct area must
be no less than 0 and must not exceed 0.3 inches (0.74 mb) of water column
(W.C.).
IMPORTANT: It is recommended that exhaust or booster fans not be used in the exhaust ductwork
system.
NOTE: As per the National Fuel Gas Code, “Exhaust ducts for Type 2 clothes dryers shall be
constructed of sheet metal or other noncombustible material. Such ducts shall be equivalent in
strength and corrosion resistance to ducts made of galvanized sheet steel not less than 26
gauge (0.0195-inches [0.50 mm]) thick.”
113307-7
Maytag Co.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
SINGLE DRYER VENTING
IMPORTANT: For extended ductwork runs, the cross section area of the ductwork can only be
increased to an extent. When the ductwork approaches the maximum limits as noted
in this manual, a professional heating, ventilating, and air-conditioning (HVAC) firm
should be consulted for proper venting information.
Horizontal Venting
When horizontal dryer venting is used, the length of the ductwork from the dryer to the outside exhaust outlet,
must not exceed Dimension A (30 feet [9.144 meters]). The minimum diameter of this ductwork must be at
least Dimension B (8-inches [20.32 cm]). Including basket (tumbler)/dryer elbow connections or elbows used
for outside protection from the weather, no more than one (1) elbow should be used in the exhaust duct run. If
more than one (1) elbow is used, the cross-sectional area of the ductwork must be increased.
Vertical Venting
When vertical dryer venting is used, the length of the ductwork from the dryer to the outside exhaust outlet,
must not exceed Dimension C (20 feet [6.096 meters]). The minimum diameter of this ductwork must be at
least Dimension D (8-inches [20.32 cm]). Including basket (tumbler)/dryer elbow connections or elbows used
for outside protection from the weather, no more than three (3) elbows should be used in the exhaust duct run.
If more than three (3) elbows are used, the cross-sectional area of the ductwork must be increased.
NOTE 1 Opening must be 2-inches (5.08 cm) larger than the duct (all the way around). The duct must be centered within this opening.
NOTE 2 Distance should be 2 times the diameter of the duct to the nearest obstruction.
10
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
MULTIPLE DRYER (COMMON) VENTING
IMPORTANT: For extended ductwork runs, the cross section area of the ductwork can only be
increased to an extent. When the ductwork approaches the maximum limits as noted
in this manual, a professional heating, ventilating, and air-conditioning (HVAC) firm
should be consulted for proper venting information.
If it is not feasible to provide separate exhaust ducts for each dryer, ducts from individual dryers may be
channeled into a “common main duct.” The individual ducts should enter the bottom or side of the main duct at
an angle not more than 45º in the direction of airflow. The main duct should be tapered, with the diameter
increasing before each individual duct is added. The minimum diameter of the individual ductwork (Dimension
A) must be at least 8-inches (20.32 cm).
IMPORTANT: No more than four (4) dryers should be connected to one (1) main common duct.
The illustration below shows the minimum cross-sectional area for multiple dryer round or square venting.
These figures must be increased if the main duct run from the last dryer to where it exhausts to the outdoors is
longer than Dimension B or has more than one (1) elbow in it.
For gas models Dimension B is 20 feet (6.096 meters).
Multiple Dryer Venting (Gas) with 8-Inch (20.32 cm) Diameter
460 cfm (13 cmm) Exhaust Connections at Common Duct
NUMBER OF DRYERS
4
3
120
774
12
2
80
1
54
SQ IN
164
1058
14
MINIMUM CROSS-
SECTIONAL AREA
SQ CM
IN
516
10
348
8
MINIMUM ROUND
DUCT DIAMETER
CM
35.56
30.48
25.4
20.32
NOTE 1 Opening must be 2-inches (5.08 cm) larger than the duct (all the way around). The duct must be centered within this opening.
NOTE 2 Distance should be 2 times the diameter of the duct to the nearest obstruction.
113307-7
Maytag Co.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
F. ELECTRICAL INFORMATION
1. Electrical Requirements
ALL electrical connections must be made by a properly licensed and competent electrician. This
is to ensure that the electrical installation is adequate and conforms to local and state regulations or codes.
In the absence of such codes, ALL electrical connections, materials, and workmanship must conform to
the applicable requirements of the National Electrical CodeANSI/NFPANO. 70-LATEST EDITION or in
Canada, the Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION.
IMPORTANT: Failure to comply with these codes or ordinances, and/or the requirements stipulated
in this manual can result in personal injury or component failure.
NOTE: Component failure due to improper installation will VOID THEWARRANTY.
Each dryer should be connected to an independently protected branch circuit. The dryer must be connected
with copper wire only. DO NOT use aluminum wire; it could create a fire hazard. The copper
conductor wire/cable must be of proper ampacity and insulation in accordance with electric codes for
making ALL service connections.
NOTE: The use of aluminum wire willVOIDTHEWARRANTY.
IMPORTANT: Aseparate protected circuit must be provided to each dryer.
NOTE: An individual ground circuit must be provided to each dryer, do not daisy chain.
IMPORTANT: The dryer must be connected to the electric supply shown on the dryer data label. In
the case of 208 VAC or 240 VAC, the supply voltage must match the electric service
specifications of the dryer data label exactly.
IMPORTANT: The wire size must be properly sized to handle the related current.
WARNING: 208 VACAND 240 VACARE NOT THE SAME. Any damage done to dryer
components due to improper voltage connections will automatically VOID THE
WARRANTY.
NOTE: Component failure due to improper voltage application willVOID THEWARRANTY.
NOTE: The manufacturer reserves the right to make changes in specifications at any time without
notice or obligation.
12
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Electrical Service Specifications
ELECTRICAL SERVICE SPECIFICATIONS (PER DRYER)
IMPORTANT: 208 VAC AND 240 VAC ARE NOT THE SAME. When ordering,
specify exact voltage.
NOTES: A.
When fuses are used they must be dual element, time delay, current
limiting, class RK1 or RK5 ONLY. Calculate/determine correct fuse
value, by applying either local and/or National Electrical Codes to
listed appliance amp draw data.
B. Circuit breakers are thermal-magnetic (industrial) motor curve type
ONLY. For others, calculate/verify correct breaker size according to
appliance amp draw rating and type of breaker used.
APPROX.
SERVICE
VOLTAGE
WIRE
SERVICE
CIRCUIT
BREAKER
PHASE
AMP DRAW
60 Hz
50 Hz
120
1ø
2
8.7
4.6
15
6/25/08
3. Grounding
A ground (earth) connection must be provided and installed in accordance with state and local codes. In
the absence of these codes, grounding must conform to applicable requirements of the National Electrical
Code ANSI/NFPA NO. 70-LATEST EDITION, or in Canada, the installation must conform to applicable
Canada Standards: Canadian Electrical Codes Parts 1 & 2 CSA C22.1-1990 or LATEST EDITION. The
ground connection may be to a proven earth ground at the location service panel.
For added personal safety, when possible, it is suggested that a separate ground wire be connected from the
ground connection of the dryer to a grounded cold water pipe. DO NOT ground to a gas pipe or hot
water pipe. The grounded cold water pipe must have metal-to-metal connection ALL the way to the
electrical ground. If there are any nonmetallic interruptions, such as, a meter, pump, plastic, rubber, or other
insulating connectors, they must be jumped out with no. 4 copper wire and securely clamped to bare metal
at both ends.
IMPORTANT: For personal safety and proper operation, the dryer must be grounded.
Provisions are made for ground connection in each dryer at the electrical service connection area.
4. Electrical Connections
A wiring diagram is located inside the control box for connection data.
If local codes permit, power to the dryer can be made by the use of a flexible U.L. listed power cord/pigtail
(wire size must conform to rating of dryer), or the dryer can be hard wired directly to the service breaker
panel. In both cases, a strain relief must be installed where the wiring enters the dryer.
IMPORTANT: Aseparate protected circuit must be provided to each dryer.
113307-7
Maytag Co.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
a. Single-Phase (1ø) Wiring Connections/Hookup
The electrical input connections on ALL single-phase (1ø)
gas dryers are made into the rear service box located at the
upper left area of the dryer.
Single-Phase Electrical Lead Connections
White or Red
+
Black
+
Positive
Green
+
Ground
Neutral
or L2
FOR 110VAPPLICATIONS
FOR 208-240VAPPLICATIONS
A ground lug is provided in the rear electrical box to connect your service ground.
14
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
G. GAS INFORMATION
It is your responsibility to have ALL plumbing connections made by a qualified professional to ensure that the
gas plumbing installation is adequate and conforms to local and state regulations or codes. In the absence of
such codes, ALL plumbing connections, materials, and workmanship must conform to the applicable requirements
of the National Fuel Gas CodeANSI Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes
CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid Propane [L.P.] Gas) or LATEST
EDITION.
IMPORTANT: FAILURE TO COMPLYWITH CODES OR ORDINANCES,AND/OR
REQUIREMENTS IN THIS MANUAL, CAN RESULT IN PERSONAL
INJURYAND IMPROPER OPERATION OFTHE DRYER.
The dryer and its individual shutoff valves must be disconnected from the gas supply piping system during any
pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa). The dryer must be isolated
from the gas supply piping system by closing its individual manual shutoff valve during any pressure test of the
gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).
IMPORTANT: Failure to isolate or disconnect the dryer from supply as noted can cause irreparable
damage to the gas valve, which will VOID THEWARRANTY.
WARNING: FIRE OR EXPLOSION COULD RESULT DUE TO FAILURE OF
ISOLATINGOR DISCONNECTINGTHE GAS SUPPLYAS NOTED.
1. Gas Supply
The gas dryer installation must meet the American National Standard...National Fuel Gas Code ANSI
Z223.1-LATEST EDITION, or in Canada, the Canadian Installation Codes CAN/CGA-B149.1 M91 (Natural
Gas) or CAN/CGA-B149.2-M91 (L.P. Gas) or LATEST EDITION, as well as local codes and ordinances
and must be done by a qualified professional.
NOTE: Undersized gas piping will result in ignition problems, slow drying, increased use of energy, and
can create a safety hazard.
The dryer must be connected to the type of heat/gas indicated on the dryer data label. If this information
does not agree with the type of gas available, DO NOT operate the dryer. Contact the dealer who sold
the dryer or contact the Maytag Co.
IMPORTANT: Any burner changes or conversions must be made by a qualified professional.
The input ratings shown on the dryer data label are for elevations up to 2,000 feet (610 meters), unless
elevation requirements of over 2,000 feet (610 meters) were specified at the time the dryer order was
placed with the factory. The adjustment or conversion of dryers in the field for elevations over 2,000 feet
(610 meters) is made by changing each burner orifice. If this conversion is necessary, contact the dealer
who sold the dryer or contact the Maytag Co.
113307-7
Maytag Co.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Technical Gas Data
a. Gas Specifications
TYPE OF GAS
NATURAL
LIQUID PROPANE
8.7 mb
26.1 mb
27.4 mb
Manifold Pressure*
3.5 inches W.C.
6.0 - 12.0 inches W.C.
10.5 inches W.C.
11.0 inches W.C.
14.92 - 29.9 mb
In-Line Pressure
Shaded areas are stated in metric equivalents
*Measured at outlet side of gas valve pressure tap when gas valve is on.
b. Gas Connections
Inlet connection............... 1/2” N.P.T.
Inlet supply size............... 1/2” Diameter Pipe (minimum)
Heat input (per dryer) ..... 100,000 Btu/hr (25,200 kcal/hr)
1) Natural Gas
Regulation is controlled by the dryer’s gas valve’s internal regulator. Incoming supply pressure
must be consistent between a minimum of 6.0 inches (14.92 mb) and a maximum of 12.0 inches
(29.9 mb) water column (W.C.) pressure.
2) Liquid Propane (L.P.) Gas
Dryers made for use with L.P. gas have the gas valve’s internal pressure regulator blocked open so
that the gas pressure must be regulated upstream of the dryer. The pressure measured at each
gas valve pressure tap must be a consistent 10.5 inches (26.1 mb) water column. There is no
regulator or regulation provided in an L.P. dryer. The pressure must be regulated at the source
(L.P. tank) or an external regulator must be added to each dryer.
TYPE OF GAS
Liquid
Propane
Conversion Kit
Part Number
Natural
Liquid Propane
Btu
Per Hour
Rating
kcal/hr
Rating
Part
Part
Number
Qty. D.M.S.*
Qty. D.M.S.*
#46
Number
25,200
100,000
2
#29
140820
2
140806
883321
Shaded area is stated in metric equivalent
* Drill Measurement Size (D.M.S.) equivalents are as follows:
Natural Gas ............................. #29 = 0.1360” (3.4540 mm).
Liquid Propane Gas ................. #46 = 0.810” (2.0574 mm).
16
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Piping Connections
ALL components/materials must conform to National Fuel Gas Code SpecificationsANSI Z223.1-LATEST
EDITION, or in Canada, CAN/CGA-B149.1-M91 (Natural Gas) or CAN/CGA-B149.2-M91 (Liquid
Propane [L.P.] Gas) or LATEST EDITION (for General Installation and Gas Plumbing), as well as local
codes and ordinances and must be done by a qualified professional. It is important that gas pressure
regulators meet applicable pressure requirements, and that gas meters be rated for the total amount of
ALL the appliance Btu being supplied.
The dryer is provided with a 1/2” N.P.T. inlet pipe connection extending out the back area of the burner
box. The minimum pipe size (supply line) to the dryer is 1/2” diameter. For ease in servicing, the gas supply
line of each dryer must have its own shutoff valve.
The size of the main gas supply line (header) will vary depending on the distance this line travels from the
gas meter or, in the case of L.P. gas, the supply tank, other gas-operated appliances on the same line, etc.
Specific information regarding supply line size should be determined by the gas supplier.
NOTE: Undersized gas supply piping can create a low or inconsistent pressure, which will result in
erratic operation of the burner ignition system.
Consistent gas pressure is essential at ALL gas connections. It is recommended that a 3/4-inch
(19.05 mm) pipe gas loop be installed in the supply line servicing a bank of dryers. An in-line pressure
regulator must be installed in the gas supply line (header) if the (natural) gas pressure exceeds 12.0 inches
(29.9 mb) of water column (W.C.) pressure. (Refer to the illustrations below.)
113307-7
Maytag Co.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: A water column test pressure of 3.5 inches (8.7 mb) for natural gas and 10.5 inches (26.1 mb)
for liquid propane (L.P.) dryers is required at the gas valve pressure tap of each dryer for
proper and safe operation.
A 1/8” N.P.T. plugged tap, accessible for a test gauge connection, must be installed in the main gas supply
line immediately upstream of each dryer.
IMPORTANT: Pipe joint compounds that resist the action of natural gas and L.P. gas must be used.
IMPORTANT: Test ALL connections for leaks by brushing on a soapy water solution (liquid
detergent works well).
WARNING: NEVER TEST FOR LEAKS WITHA FLAME!!!
IMPORTANT: The dryer and its individual shutoff valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of
1/2 psig (3.5 kPa).
NOTE: The dryer must be isolated from the gas supply piping system by closing its individual manual
shutoff valve during any pressure test of the gas supply system at test pressures equal to or less
than 1/2 psig (3.5 kPa).
H. PREPARATION FOR OPERATION/START-UP
The following items should be checked before attempting to operate the dryer:
1. Read ALL “CAUTION,” “WARNING,” and “DIRECTION” labels attached to the dryer.
2. Check incoming supply voltage to be sure that it is the same as indicated on the dryer data label.
3. GAS MODELS – check to ensure that the dryer is connected to the type of gas indicated on the dryer
data label.
4. GAS MODELS – the sail switch damper assembly was installed and adjusted at the factory prior to
shipping. However, each sail switch adjustment must be checked to ensure that this important safety
control is functioning.
5. Check bolts, nuts, screws, terminals, and fittings for tightness and security.
6. GAS MODELS – be sure that ALL gas shutoff valves are in the open position.
7. Check that ALL back guard panels and service box covers have been replaced.
8. Check the lint door/drawer to ensure that it is closed and secured in place.
9. Rotate the basket (tumbler/drum) by hand to be sure it moves freely.
10. Check basket (tumbler) bearing setscrews to ensure that they are ALL tight.
11. Check vent is connected to the dryer and is exhausted to the outdoors.
18
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
I. PREOPERATIONAL TESTS
ALL dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational test
should be performed before the dryer is publicly used. It is possible that adjustments have changed in transit or
due to marginal location (installation) conditions.
1. Turn on electric power to the dryer.
2. Refer to the Operating Instructions for starting your particular model dryer.
3. GAS MODELS ONLY
a. When a gas dryer is first started (during initial start-up), it has a tendency not to ignite on the first ignition
attempt. This is because the gas supply piping is filled with air, so it may take a few minutes for the air
to be purged from the lines.
NOTE: During the purging period, check to be sure that ALL gas shutoff valves are open.
NOTE: Gas model dryers are equipped with an ignition system, which has internal diagnostics. If
ignition is not established after one (1) time, the heat circuit in the ignition module will attempt
two (2) more ignitions (total of three [3] ignition attempts). If there is no flame after the third
ignition attempt the module will lock out until it is manually reset. To reset the ignition system,
open and close the main door and restart the dryer.
b. A gas pressure test should be taken at the gas valve pressure tap of each dryer to ensure that the
water column (W.C.) pressure is correct and consistent.
NOTE: Water column pressure requirements (measured at the pressure tap of the gas valve body):
Natural Gas................................ 3.5 Inches (8.7 mb) Water Column.
Liquid Propane (L.P.) Gas .......... 10.5 Inches (26.1 mb) Water Column.
IMPORTANT: There is no regulator provided in an L.P. dryer. The water column pressure must be
regulated at the source (L.P. tank), or an external regulator must be added to each
dryer.
4. Make a complete operational check of ALL safety related circuits:
a. Door Switch(es)
b. Hi-Limit Thermostats
c. Cycling Thermostat
d. Sail Switch
NOTE: The sail switch can be checked for proper operation by opening the lint door/drawer. While
pushing the lint door/drawer switch in, start a drying cycle. The heating unit should not
activate (wait 30-seconds). If heat does activate, make the necessary adjustments to the sail
switch.
5. Make a complete operational check of ALL operating controls.
113307-7
Maytag Co.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If computer program changes are required, refer to the computer programming section of the
manual supplied with the dryer.
6. The dryer should be operated through one (1) complete cycle to ensure that no further adjustments are
necessary and that ALL components are functioning properly.
BASKET (TUMBLER) COATING
The basket (tumbler) is treated with a protective coating. We suggest dampening old garments or cloth material
with a solution of water and nonflammable mild detergent and tumbling them in the basket (tumbler) to remove
this coating.
J. PREOPERATIONAL INSTRUCTIONS
Microprocessor Controller (Computer) Models
1. The light emitting diode (L.E.D.) display reads “READY” (no cycle in progress).
2. Press the letter on the keyboard (touch pad) corresponding to the cycle desired (i.e., key “D”).
3. The dryer will then start. (I.E., blower, basket [tumbler], and heat).
4. The L.E.D. display will read MANUAL DRYING CYCLE D, 00:00 MIN REMAIN.
NOTE: The dryer can be stopped at any time by pressing the “STOP/CLEAR” key, at this time the
dryer will go into a cycle pause. If the “STOP/CLEAR” key is pressed again at this point, the
cycle that was in progress will be cancelled and returned to the “READY” state.
5. When the programmed drying time has expired, the Phase 7 non-coin microprocessor controller (computer)
will proceed into the Cool Down Cycle.
6. Once the Cool Down Cycle begins at the end of the heat cycle, the L.E.D. display will read COOL DOWN
TEMP ___/___ MINUTES REMAINING. At the end of the heat cycle, the dryer will shut off the heat
and continue the fan and basket (tumbler) until the Cool Down Time or temperature is reached.
IMPORTANT: For more detailed information regarding the microprocessor controller (computer) on
the dryer, refer to the microprocessor user’s manual included with the dryer.
DUAL TIMER DRYERS
1. Turn drying timer knob for a time of 20 minutes.
2. Select “High Temp.”
3. Push “Push to Start” button.
4. To stop dryer, open the main door.
20
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSING TIMER SPIN/DWELL ADJUSTMENTS
Timer models have an electronic reversing timer in the electrical service box, which is located in the upper left
rear area of the dryer.
Both the Dwell (stop) Time and the basket (tumbler) Spin Time are adjustable by mode selection switches
located on the electronic timer (as noted in the illustration below).
TIMING LEGEND
SPIN TIME
Adjustment Position Number
Time in Seconds*
1
2
3
4
5
30
60
90
120 150
DWELL (STOP) TIME
Adjustment Position Number
Time in Seconds*
1
5
2
3
4
5
6.3
7.6
8.9 10.2
* Values shown are +/- 1-second.
K. SHUTDOWN INSTRUCTIONS
If the dryer is to be shutdown (taken out of service) for a period of time, the following must be performed:
1. Discontinue power to the dryer either at the external disconnect switch or the circuit breaker.
2. Discontinue the heat supply:
GAS MODELS – discontinue the gas supply.
a. SHUT OFF external gas supply shutoff valve.
b. SHUT OFF internal gas supply shutoff valve located in the gas valve burner area.
113307-7
Maytag Co.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION IV
SERVICE/PARTS INFORMATION
A. SERVICE
Service must be performed by a qualified trained technician, service agency, or gas supplier. If service is
required, contact the dealer from whom the Maytag equipment was purchased. If the dealer cannot be
contacted or is unknown, contact the Maytag Co. for a dealer in your area.
NOTE: When contacting the Maytag Co., be sure to give the correct model number and serial
number so that the inquiry is handled in an expeditious manner.
B. PARTS
Replacement parts should be purchased from the dealer from whom the Maytag equipment was purchased. If
the dealer cannot be contacted or is unknown, contact the Maytag Co. for a dealer in your area.
NOTE: When ordering replacement parts from the Maytag dealer or the Maytag Co. be sure to
give the correct model number and serial number so that the parts order can be
processed in an expeditious manner.
22
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION V
WARRANTY INFORMATION
A. RETURNING WARRANTY CARDS
1. Before any dryer leaves the manufacturer’s test area, a warranty card is placed on the back side of the
main door glass. These warranty cards are intended to serve the customer where we record the individual
installation date and warranty information to better serve you should you file a warranty claim.
IMPORTANT: Aseparate warranty card must be completed and returned for each individual dryer.
NOTE: Be sure to include the installation date when returning the warranty card(s).
B. WARRANTY
For a copy of the manufacturer’s commercial warranty covering your particular dryer(s), contact the Maytag
dealer from whom you purchased the equipment and request a dryer warranty form. If the dealer cannot be
contacted or is unknown, warranty information can be obtained from the Maytag Co.
NOTE: Whenever contacting the Maytag Co. for warranty information, be sure to have the dryer’s
model number and serial number available so that the inquiry can be handled in an
expeditious manner.
113307-7
Maytag Co.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTIONVI
ROUTINE MAINTENANCE
A. CLEANING
A program and/or schedule should be established for periodic inspection, cleaning, and removal of lint from
various areas of the dryer, as well as throughout the ductwork system. The frequency of cleaning can best be
determined from experience at each location. Maximum operating efficiency is dependent upon proper air
circulation. The accumulation of lint can restrict this airflow. If the guidelines in this section are met, a Maytag
dryer will provide many years of efficient, trouble free, and most importantly safe operation.
WARNING: LINT FROM MOST FABRICS IS HIGHLYCOMBUSTIBLE. THE
ACCUMULATION OFLINT CAN CREATEAPOTENTIALFIRE HAZARD.
WARNING: KEEPDRYERAREACLEARAND FREE FROM COMBUSTIBLE
MATERIALS, GASOLINE, AND OTHER FLAMMABLE VAPORSAND
LIQUIDS.
NOTE: Suggested time intervals shown are for average usage which is considered six (6) to eight (8)
operational (running) hours per day.
IMPORTANT: Dryer produces combustible lint and must be exhausted to the outdoors. Every 6
months, inspect the exhaust ducting and remove any lint buildup.
SUGGESTED CLEANING SCHEDULE
EVERY THIRD OR FOURTH LOAD
Clean the lint screen every third or fourth load. A clogged lint screen will cause poor dryer performance. The
lint screen is located behind the lint door/drawer. Open the lint door/drawer, brush or vacuum the lint off the lint
screen, and remove the lint. Inspect lint screen and replace if torn.
NOTE: The frequency of cleaning the lint screen can best be determined from experience at each
location.
WEEKLY
Clean lint accumulation from lint chamber, thermostat, and microprocessor temperature sensor (sensor bracket)
area.
WARNING: TOAVOID THE HAZARD OFELECTRICALSHOCK, DISCONTINUE
ELECTRICALSUPPLYTOTHE DRYER.
24
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
90 DAYS
Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryer’s internal
exhaust ducting.
WARNING: THEACCUMULATION OFLINT IN THE EXHAUST DUCTWORK CAN
CREATEAPOTENTIALFIRE HAZARD.
WARNING: DO NOT OBSTRUCT THE FLOW OF COMBUSTIONAND VENTILATION
AIR.
WARNING: INSPECTAND REMOVEANYLINTACCUMULATION, WHICH CAN CAUSE
THE BACK DRAFT DAMPER TO BIND OR STICK.
NOTE: A back draft damper that is sticking partially closed can result in slow drying and shutdown of
heat circuit safety switches or thermostats.
NOTE: When cleaning the dryer cabinet(s), avoid using harsh abrasives. Aproduct intended for the
cleaning of appliances is recommended.
B. ADJUSTMENTS
7 DAYS AFTER INSTALLATION AND EVERY 6 MONTHS THEREAFTER
Inspect bolts, nuts, screws, setscrews, grounding connections, and nonpermanent gas connections (unions, shutoff
valves, and orifices). Motor and drive belts should be examined. Cracked or seriously frayed belts should be
replaced. Tighten loose V-belts when necessary. Complete an operational check of controls and valves. Complete
an operational check of ALL safety devices (door switches, lint door/drawer switch, sail switch, burner, and
hi-limit thermostats).
C. LUBRICATION
The motor bearings, idler bearings, and under normal/most conditions the basket (tumbler) bearings are permanently
lubricated. It is physically possible to relubricate the basket (tumbler) bearings if you choose to do so even
though this practice is not necessary. Use Shell Alvania #2 grease or its equivalent. The basket (tumbler)
bearings used in the dryer DO NOT have a grease fitting. Provisions are made in the bearing housing for the
addition of a grease fitting which can be obtained elsewhere, or from the Maytag dealer by ordering kit
P/N 882159 (includes two [2] fittings).
113307-7
Maytag Co.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION VII
DATALABELINFORMATION
When contacting the Maytag dealer, certain information is required to ensure proper service/parts information.
This information is on the dryer data label affixed to the left side panel area behind the top control (access) door.
When contacting the Maytag Co., please have the model number and serial number available.
1. MODEL NUMBER – Describes the style of dryer and type of heat (gas, electric, or steam).
2. SERIALNUMBER –Allows the manufacturer to gather information on your particular dryer.
3. MANUFACTURINGCODE NUMBER – The number issued by the manufacturer, which describes ALL possible options
on your particular model.
4. TYPE OF HEAT – This describes the type of heat for your particular dryer, gas (either natural gas or liquid propane [L.P.]
gas), electric, or steam.
5. HEAT INPUT (for GAS DRYERS) – This describes the heat input in British Thermal Units per Hour (Btu/hr).
6. ORIFICE SIZE (for GAS DRYERS) – Gives the number drill size used.
7. ELECTRIC SERVICE – This describes the electric service for your particular model.
8. GAS MANIFOLD PRESSURE (for GAS DRYERS) – This describes the manifold pressure taken at the gas valve tap.
26
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION VIII
PROCEDURE FOR FUNCTIONAL CHECK
OF REPLACEMENT COMPONENTS
1. Microprocessor Controller (Computer) Board
a. Upon completing installation of the replacement microprocessor controller (computer) board, reestablish
power to the dryer.
b. Start the drying cycle by pressing any of the preset cycles in letters A-F.
c. Verify that the applicable indicator lights on the back side of the microprocessor controller (computer)
board are lit. (Refer to the illustration below.)
113307-7
Maytag Co.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
2. For Models with Direct Spark Ignition (DSI) Module (Type I)
Theory of Operation:
Start the drying cycle. When the gas burner ignites within the
chosen trial for ignition time (6-seconds), the flame sensor detects
gas burner flame and signals the DSI module to keep the gas
valve open as long as there is a call for heat. The DSI module
will “LOCKOUT” if the gas burner flame is not sensed at the
end of the trial for ignition period. The trial for ignition period will
be repeated for a total of three (3) retries/trials (the initial try and
two [2] more retries/trials). If the flame is not sensed at the end
of the third retry/trial (inter-purge period of 30-seconds), the DSI
module will “LOCKOUT” (light emitting diode [L.E.D.] diagnostic
indicator flashes).
A steady L.E.D. indicator indicates normal operation.
No L.E.D. indicator indicates a power or an internal failure has occurred.
3. For Models with DSI Module (Type II)
Theory of Operation:
Start the drying cycle. When the gas burner ignites within the
chosen trial for ignition time (8-seconds), the flame sensor detects
gas burner flame and signals the DSI module to keep the gas
valve open as long as there is a call for heat. The DSI module
will “LOCKOUT” if the gas burner flame is not sensed at the
end of the trial for ignition period. The trial for ignition period will
be repeated for a total of three (3) retries/trials (the initial try and
two [2] more retries/trials). If the flame is not sensed at the end
of the third retry/trial (inter-purge period of 30-seconds), the DSI
module will “LOCKOUT” (a red L.E.D. diagnostic indicator will
flash).
An unlit red L.E.D. diagnostic indicator indicates normal operation.
Alit green L.E.D. diagnostic indicator indicates dryer controller is calling for heat and that ALL interlocks
have been satisfied.
28
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION IX
FIRE SUPPRESSION SYSTEM
Fire Suppression System In Action
The exclusive fire suppression system will extinguish fires that may start in the drying basket (tumbler). Aseries
of sensors positioned throughout the basket (tumbler) and interfaced with the Phase 7 microprocessor controller
(computer) will trigger the fire suppression system water jet(s) to extinguish the flames quickly. The water jet(s)
remain on for 2 minutes and will automatically activate again if a fire condition remains or reignites. While the
water jet(s) are activated, the basket (tumbler) will jog to move the water throughout the load. Until the dryer is
attended to, the Phase 7 microprocessor controller (computer) will display that the system was activated.
BEFORE YOU START!
CHECK LOCAL CODES AND PERMITS
Call your local water company or the proper municipal authority for information regarding local codes.
IMPORTANT: It is your responsibility to have ALL plumbing connections made by a qualified
professional to ensure that the plumbing installation is adequate and conforms to local,
state, and federal regulations or codes.
IMPORTANT: It is the installer’s or owner’s responsibility to see that the necessary or required
water, water pressure, pipe size, or connections are provided. The manufacturer
assumes no responsibility if the fire suppression system is not connected, installed, or
maintained properly.
113307-7
Maytag Co.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
1. Requirements
The fire suppression system must be supplied with a minimum water pipe size of 1/2” and be provided with
40 psi +/- 20 psi (2.75 bar +/- 1.37 bar) of pressure. For use of optional manual bypass, a second source
with the same piping and pressure requirements is required.
Flexible 1/2 feeds must be provided to avoid damage to electric water solenoid valve by vibration.
IMPORTANT: Flexible supply line/coupling must be used. Solenoid valve failure due to hard
plumbing connections WILLVOIDWARRANTY.
If the rear area of the dryer or the water supply is located in an area where it will be exposed to
cold/freezing temperatures, provisions must be made to protect these water lines from freezing.
WARNING: If the water in the supply line or water solenoid valve freezes, the fire suppression system
will be INOPERATIVE!!
IMPORTANT: Appliance is to be connected to the water mains using a new hose set and the old
hose set should not be reused.
2. Water Connections:
The water connection is made to the 3/4”-11.5
NH hose adaptor located at the rear upper
midsection of the dryer (refer to the photograph).
The water solenoid valve has a 3/8” M.P.T.
connection supplied with a 3/4”-11.5 NH hose
adaptor to provide the minimum 1/2-inch supply
(feed) line. Flexible supply line/coupling must
be used in an effort to avoid damaging the electric
water solenoid valve.
NOTE: The 3/4”-11.5 NH is a standard hose coupling screw thread. It is not to be confused with
3/4” N.P.T. The sealing of an NH connection is made with a washer opposed to the mating
threads of an N.P.T. assembly. The two (2) thread designs are not compatible.
IMPORTANT: Flexible supply line/coupling must be used. Solenoid valve failure due to hard
plumbing connections WILLVOIDWARRANTY. It is recommended that a filter
or strainer be installed in the water supply line.
30
Maytag Co.
113307-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Typical Water Supply
OPTIONAL MANUAL BYPASS
Provisions are made in the dryer’s fire suppression system for the installation of an optional manual bypass. The
connections for the manual bypass are made at the “T” or “three way” fitting located in the outlet supply side of
the water solenoid valve. The use and connections of this manual bypass are at the option or discretion of the
owner.
The water connection for the manual bypass is made to the “T” or “three way” fitting which has a 3/8” F.P.T.
and a coupling must be used to provide the minimum 1/2” supply (feed) line.
If the rear area of the dryer or the water supply is located in an area where it will be exposed to cold/freezing
temperatures, provisions must be made to protect these water lines from freezing.
WARNING: If the water in the supply line or water solenoid valve freezes, the fire suppression system
will be INOPERATIVE!!
113307-7
Maytag Co.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No. 113307
7 - 06/26/08 - 0
Download from Www.Somanuals.com. All Manuals Search And Download.
|