Document #: 555-640-136
Comcode 107 713 760
Issue 1, March 1996
MERLIN LEGEND®
Communications System
Releases 3.1 and 4.0
MLX Queued Call Console
Operator’s Guide
Your Queued Call Console ..................................................................................... 1
Call and Fixed Feature Buttons ........................................................................ 3–4
Feature Finder ................................................................................................ 6–8
Call Handling .............................................................................................. 10–12
Call Delivery, Answering Calls, Making Calls, Hold ................................................. 10
Messaging Feature Table ................................................................................ 13
Send/Remove Message ................................................................................... 14
Leaving Messages, Posting Messages................................................................. 16
Using Features ................................................................................................ 18
Often-Used Features ..................................................................................... 19–23
Account Codes, Alarm, Alarm Clock & Timer......................................................... 19
Authorization Codes, Barge-In .......................................................................... 20
Night Service, Paging, Park ............................................................................. 22
Display Reference ........................................................................................ 25–26
Fixed Display Buttons, Home Screen, Menu Screen, Inspect Screen ............................ 25
Inspect Screens, Feature Screen ....................................................................... 26
Notes & Reminders ....................................................................................... 27–28
Download from Www.Somanuals.com. All Manuals Search And Download.
Your Queued Call Console
Your Display Screen
More
The > appears on the screen when more information
exists. Press More to advance through additional menus
when necessary or to display more information about an
incoming or active call.
Your telephone’s display is an alarm clock and timer (see p. 19),
telephone directory (see p. 17), and message center (see pp. 13–16).
Read the button descriptions on this page to find out how you can
use your screen to locate and activate features or see who’s calling
you. See pp. 25–26 for more information.
TEL/OTHERJack(underside)OnMLX-10DP,MLX-16DP,
MLX-20L,andMLX-28Dtelephonesisaconnectionfora
Multi-function Module (MFM).
Home
DSS Jack (underside) On MLX-20L and MLX-28D
telephones: connects to a DSS or PassageWay™ Direct
ConnectSolutionorPassageWaySolution.
Press to return to the Home screen and exit the current
activity. The Home screen gives calling and timekeeping
information, and prompts when you need help.
Home
Menu
More
Inspct
Inspct
Menu
Press Inspct and a Call button to display information
about an incoming or active call. Press Inspct and a
fixed feature button to see what feature is programmed on
the button (see p. 21).
7 Lines
24 Characters
Press to program the phone, view messages, or select features
available from the display (see More).
Voice Announce
If Voice Announce is enabled through system programming,
press to make a Voice Announce call to another extension.
Unlabled Display Buttons
Press one to select the item next to it on the display.
Note:
Call and Fixed Feature Buttons
See pp. 3–4 for details.
The one or two DSSs (Direct Station Selectors) that attach
to your MLX-20L telephone are not shown here. See p. 2
for details.
Message Light
Indicates a waiting message when the red LED is lit (see
pp. 13–16).
Volume
V
Message
DEF
3
Press or to change the ringer loudness while the
Volume
Feature
V
1
A2BC
J5KL
T5UV
Transfer
phone is ringing, handset volume while you’re using the
handset, or speaker volume while you’re using the speaker.
Transfer
Conf
M6NO
WX6YZ
GHI
4
Press to send a call to another phone. It’s better to use the
Start button (see p. 4).
HFAI
Mute
PQRS
4
Feature
Drop
Conf
Press to display the Feature screen and select features.
OPER
0
Speaker
Hold
Press to add a person to a conference (see p. 11).
HFAI
Not used on a QCC.
Drop
Mute
Press Drop and a line button to disconnect a person from
a conference call (see p. 11).
Press to turn the speakerphone
microphone on or off so that
you can or cannot be heard
by the caller.
User Card Tray
Speaker
Hold
Pull out for quick reference.
Press to turn the speakerphone on/off
for hands-free conversation during a
call or when a call rings; or press to
hang up a speakerphone call.
Press to put a call on hold
(see p. 10).
!
CAUTION:
To clean your phone, unplug it from the wall jack and use a
slightly dampened cloth. To prevent permanent damage, do
not immerse the phone in water or any liquid, and do not
use liquid or aerosol cleaners directly on the telephone.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Your DSS
DSS Buttons
Each DSS has 50 DSS buttons, arranged in 5 columns of 10 buttons each.
DSS buttons have numbers assigned in consecutive order, starting with
the top left corner button. Each button can have 3 numbers assigned to it,
which can correspond to the following:
• Extension numbers for directing or making calls to co-workers
(see pp. 10–12)
00
01
02
03
04
10
11
12
13
14
20
21
22
23
24
30
31
32
33
34
40
41
42
43
44
• Paging numbers for paging co-workers over speakerphones or
loudspeaker system (see p. 22)
Fixed Page Buttons
Press the fixed Page buttons to change the page
of telephone numbers accessible to your DSS. The
green light turns on next to the Page button that is
active. If you have one DSS, Page 1 accesses the
first 50 extensions, Page 2 accesses the second
50 extensions, Page 3 accesses the third 50
extensions. If you have two DSSs, Page 1
accesses the first 100 extensions, Page 2
accesses the second 100 extensions, Page 3
accesses the third 100 extensions.
• Numbers for parking calls to the system operator park zones (see p. 22)
• Pools and lines for monitoring the pools’ current status
05
06
07
08
09
15
16
17
18
19
25
26
27
28
29
35
36
37
38
39
45
46
47
48
49
Direct Voice Mail
Press this button to transfer a call directly to a co-worker’s voice mail
(see p. 15).
Reserved Buttons
These buttons are reserved for future use.
Message Status Button
When Message Status is on, the red lights next
to the DSS buttons turn on for extensions with
messages from system operators. Messages from
other sources (such as co-workers and fax
machines) do not cause the red lights to turn on.
The green light next to the Message Status
button turns on when the button is pressed to
tell you that the lights on the DSS are showing
Message Status. Pressing the button again turns
off Message Status and the green light.
- DSS Button Lights -
Light
Button/Meaning
Off
Extensions. Phone is not in use and Do Not Disturb is off. With the Message
Status button, the Message light is off at the extension.
Pool. One or more lines in the pool are available.
Line. Not in use (available).
Group Page, Page All, Park Zone. Not in use (available).
Calling Group. The numbering of calls waiting for calling group are fewer than the
programmed maximum.
Steady
Extensions. A co-worker is on phone, a call is on hold, or Do Not Disturb is on.
With the Message Status button, the Message light is on at the extension.
Pool. All lines in the pool are busy.
Line. In use (not available).
Group Page, Page All. In use (not available).
Calling Group. The number of calls waiting for the calling group is equal to or
more than the programmed maximum.
Fast flashing
Slow flashing
Extensions. A co-worker is calling you, or a parked call or call on hold is
returning to you.
Line. A parked or held call is returning to you.
Extensions. A call directed to this extension is returning to you.
Line. A call is ringing on this line at your console or at a co-worker’s phone.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Understanding Your QCC
Call and Fixed-Feature Buttons
The Call and fixed-feature buttons are factory-set and labeled for specific functions, as shown
in the following illustration and described below.
Letters G through Z
Call and fixed-feature button are
used to enter names into your
Personal Directory (see p. 17).
Letters A through F appear on the
display.
Fixed-Feature Buttons
See p. 4 for details.
G
K
O
S
H
L
I
J
Position
Busy
Send/
Remove
Message
Forced
Call 5
Alarm
(Ring/Voice)
Release
M
N
R
V
Z
Pool
Status
Night
Call 4
Call 3
Call 2
Service
Q
Handset/
Headset
Mute
P
T
X
Headset Headset
Status
Auto Ans
U
Source
Start
Destination Join
Y
W
Call 1
Release Cancel
Call Buttons
Buttons labeled Call 1 through Call 5
are used to make and receive inside and
outside calls (see p. 10). If Voice
Announce is enabled through system
programming, use Call 5 to make Voice
Announce calls to extensions. Voice
Announce calls made to a QCC are
received as ringing calls.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Understanding Your QCC
Fixed-Feature Buttons. Buttons for special operator functions and basic call handling:
Start begins directing the call and puts the caller on hold at Source (see p. 11).
Destination connects you with the person being called when you are directing a call
(see p. 11).
Release completes a call and frees you for the next call. It also releases you from a 3-way
conference (see p. 11).
Headset Auto Ans (Headset Auto Answer). When you use a headset, this button automatically
connects you to the next call each time a new call arrives at your console. Pressing this button
turns on the green light (see p. 9).
Handset/Headset Mute temporarily turns off the handset and headset microphone to allow
you to talk to someone privately (see p. 9).
Headset Status allows you to switch between the handset and the headset (see p. 9).
Send/Remove Message turns co-workers’ Message lights on and off (see p. 14).
Position Busy temporarily prevents most calls from being sent to your console. You continue
(see p. 23).
Alarm indicates that a problem has occurred with the system. Contact your system manager
(see p. 19).
Cancel cancels a call-directing attempt and reconnects you to the original caller on hold at the
Join connects you, the original caller (Source), and the co-worker being called (Destination)
in a 3-way conference (see p. 11).
Forced Release drops all callers (including you) from a call and frees you for another call
(see p. 11).
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Understanding Your QCC
Call & Fixed-Feature Button Lights
Each Call or fixed-feature button has a red light and a green light next to it. These lights provide the
following important information:
Light
Button/Meaning
Steady red
Call. Lift the handset or press the Speaker button to automatically
connect to the call.
Alarm.Something is wrong with the system. Contact system manager.
Handset/Headset Mute. Headset and handset microphones are off.
Steady green
Fixed-Feature Button (see pp. 3–4). Feature on button is active.
Steady red and green Call. You are on a call at this button.
Steady red and
Flashing green
Call. A call is coming in on this button.
Flashing green
Night Service. Enter the password to turn Night Service (see p. 22)
on/off.
Fast-flashing green Call, Source, Destination. A call is on hold at this button.
Tones
Tone
Meaning
Dial tone (steady)
You can make a call.
Busy (slow repeating tone)
Fast busy (fast repeating tone)
The phone you are calling is busy.
No lines are available.
Error (alternating high-low tones) You dialed a number or used a feature incorrectly.
Confirmation (double break in
dial tone followed by steady tone)
You used a feature correctly.
Rings
The table below helps you identify the different types of ringing.
Ring
Meaning
Inside call
Outside call
1 long ring
1 long ring and 1 short ring
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Feature Finder
This table shows where to look for information about performing specific console activities. Any features
that do not have detailed instructions can be used by following the instructions in Using Features, p. 18.
Handling Console Basics
If you want to ...
Then
Send outside calls to another telephone or calling
group after normal business hours.
Enter an account code before or during a call.
See Account Codes, p. 19.
Use your console as an alarm clock.
Time calls or meetings.
View the number of system alarms.
See Alarm, p. 19.
Page co-workers over their speakerphones or a
loudspeaker system.
Choose a message to leave for co-workers who have
display phones.
Screen calls on Call buttons or use your DSS to
check whether a co-worker has posted a message.
Use a headset for hands-free call handling.
Speak to someone privately while handling a call.
or when leaving your console for a period of time.
Have a co-worker’s calls ring at your console.
Cancel calls forwarded to your console.
Adjust volume of the speaker, handset, or ringer.
Put a call on hold at your console.
See Hold, p. 10.
Set up a conference with as many as four other
participants.
See Conference, p. 11.
Direct a call to a co-worker’s telephone.
See Directing Calls, p. 11.
Be notified when the number of calls in queue
exceeds the programmed threshold.
See Responding to the Queue, p. 12.
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Feature Finder
Answering and Directing Calls
If you want to ...
Then
Answer a co-worker’s ringing telephone from your
console or pick up a call on hold at a co-worker’s
telephone.
See Pickup, p. 23.
Interrupt a co-worker’s call in an emergency or if
you’re instructed to interrupt.
See Barge-In, p. 20.
Direct a call to an extension and have it wait there
until your co-worker is ready to answer it.
Camp-On, p. 21.
Put a call on hold and page a co-worker to pick up
the call at another telephone.
Notify co-workers that they have messages.
See Messaging, pp. 13–16.
Broadcast an announcement over the company’s
loudspeaker system.
See Paging, p. 22.
Page co-workers over their speakerphones.
Transfer directly to a co-worker’s voice mail.
Signal a co-worker for meetings or visitors.
See Signaling, p. 15.
Announce a call on an extension’s speakerphone,
and transfer the call.
See Directing Calls, p. 11.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Feature Finder
Making Calls
If you want to ...
Then
Make a voice-announce call.*
Enter account codes when making an outside call.
See Account Codes, p. 19.
Make an outside call from another extension, using
your own calling privileges.
Speak to someone privately while using the handset
or a headset.
Call directly to a co-worker’s voice mail.
Display or dial numbers you call frequently.
See Direct Voice Mail, p. 15.
See Personal Directory, p. 17.
Display or dial numbers your company has
programmed for you.
See Extension & System Directory, p. 17.
Messaging
Let a co-worker know you called.
See Messaging, pp. 13–16.
Find out if you have a voice mail message, fax or
other message.
Choose a message to leave for co-workers who have
display phones.
Reach a voice mailbox without calling the person.
* Release 4.0 and later systems only.
See Direct Voice Mail, p. 15.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Headsets
Headsets for the MLX Queued Call Console allow
one-touch operation, hands-free. Headsets consist
of a headpiece and modular base unit. The base
unit plugs into the handset jack.
Headpiece
Touch a Call button to answer a call, then press
Release or Forced Release to disconnect. To
eliminate the need to press a Call button, use
the Headset Auto Answer feature. See Headset
Features below.
Modular Base Unit
Handset Jack
Home
Menu
MLX-20L
More
Inspct
V
olu
m
e
Feature
Tra
n
s
fe
r
H
F
A
I
1
A
BC
Conf
M
u
te
2
G
HI
DEF
4
Mess
a
3
D
r
o
JKL
g
e
p
S
peaker
PQRS
5
MN
O
7
Hol
d
TU
6
V
8
WXYZ
Oper
9
0
#
Headpieces -
Mirage®.Receiver fits over either ear. Not for noisy environments.
StarSet®. Eartip fits in ear canal.
Supra® Monaural. Adjustable headband and soft ear cushion.
Supra Monaural Noise-Canceling (NC). Same as above with noise-canceling microphone that
reduces background noise transmission by up to 75%.
Supra Binaural. Sound in both ears.
Supra Binaural Noise-Canceling (NC). Same as above with noise-canceling microphone on
flexible boom; features windscreen and reduces background noise transmission by up to 75%.
- Headset Features -
Your console has three preprogrammed headset buttons:
• Headset Status. This button turns the headset on and off. Use this button when switching
between the handset and headset. The green light is lit when the handset mode is on.
• Headset Auto Ans (Headset Auto Answer). This button automatically delivers calls to the
headset, eliminating the need to press Call buttons to answer calls. As each call arrives, you’ll
hear a tone, and you can begin speaking immediately. The green light is lit when the Headset
Auto Answer feature is on.
• Handset/Headset Mute (Headset/Handset Mute). This button turns off your headset
microphone so that you can talk with someone in your office without being heard by a caller. Use
this button to turn off the handset’s microphone as well. The red light is lit when the handset/
headset microphones are off.
You can also turn off the headset microphone by pressing the Speaker button. The call is
transferred from your headset to the speakerphone. Press the Speaker button again to return
the call to your headset.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Call Handling
- Call Delivery -
- Making Calls -
Outside calls designated to ring at a QCC are
sent to a single common QCC queue, where
they wait to be sent to the first available QCC
operator. When a QCC operator is available to
receive a call, the system removes a call from
the queue and sends it to an idle Call button.
If more than one QCC operator is available, the
operator who has been idle the longest
receives the call.
The order in which calls are delivered to the
QCC operator is determined by system
programming. See your system manager if
callers complain about slow response times.
Both inside and outside calls ring on Call
buttons on the QCC. The QCC receives one
call at a time, regardless of the number of calls
in the QCC queue. When a call rings on a Call
button, information about the incoming call is
shown on the display.
To make an inside call:
1.Initiate Call:
• Lift the handset
OR
• Press the Speaker button
OR
• Press a Call button if using the headset.
2. Press the DSS button or dial the extension.
To make an inside Voice Announce call*:
If using a headset, go to Step 2.
1. Lift the handset, press the Speaker button.
2. Press the Call 5 button.
3. Press the DSS button or dial the extension.
To make an outside call:
As of Release 3.1, QCCs do not have access to
pools (by default). See your system manager
If an account code is required on your system,
enter it before you make the call. (See
Account Codes, p. 19.)
1. Lift the handset, press the Speaker button,
or press a Call button if using the headset.
- Answering Calls -
You can answer a call in three ways:
• Lift the handset
• Use a headset:
2. Dial the dial-out code or pool access code
and then dial the phone number.
* Release 4.0 and later systems only.
Press a Call button if you are not using
Headset Auto Answer (see p. 9).
If you are using Headset Auto Answer,
you hear a beep and can begin talking
immediately.
- Hold -
Pressing the Hold button to put a caller on
calls from the QCC queue. You can also use
the Hold button to temporarily leave a
To disconnect from a call, press Release or
Forced Release. If the automatic release
feature is programmed, calls disconnect when
you press another Call button.
conference call. (See Conference, p. 11.)
To use Hold:
The Handset/Headset Mute button on your
console enables you to turn off your handset or
headset microphone so you can have a private
conversation, when necessary.
Press the Hold button on your console. To
return to the first call, press the Call button
While a call is being directed, the caller is
automatically put on hold after you press
Start. See Directing Calls, p. 11, for more
details.
When using a headset with Headset Auto
Answer turned on, placing a call on hold turns
Headset Auto Answer off. Press the Headset
Auto Ans button to turn it on again.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Call Handling
- Conference -
- Directing Calls -
Use this feature to connect yourself, up to two
other inside extensions, and up to two outside
participants. All calls are joined on a single
Call button. You can only drop yourself or the
most recently added participant from the
conference call.
You can direct a call and announce it or not.
Check with your system manager to find out
whether automatic completion is programmed
for your console.
To direct a call without announcing and with
automatic completion:
1. Make the first call. Announce call if
necessary.
Press the DSS button for the co-worker who
will receive the call.
2. Press the Conf button to put the call on
hold. The system automatically selects
another Call button.
To direct a call without announcing or
automatic completion:
1. Press the DSS button for the co-worker who
should receive the call.
2. Press the Release button.
To direct a call without announcing, automatic
completion, or a DSS button:
1. Press the Start button.
2. Dial the extension.
3. Press the Release button.
To direct a call and announce it:
1. To put the caller on hold at the Source
button, press the Start button.
2. To announce the call on the remote
telephone’s speakerphone (Voice
Announce), press the Call 5 button.
Otherwise, go to step 3.
3. Dial the extension or press the DSS button
for the person to receive call. (If busy, see
below.)
3. Dial the next telephone number or
extension,
OR
Press the DSS button.
4. Announce call if necessary and press the
Conf button.
If the person is unavailable, press the Drop
button and press the Call button to rejoin
the conference.
5. To add more participants, repeat Steps 2–4.
• To drop out of the conference
temporarily, press the Hold button.
• To rejoin the conference, press the Call
button for the conference.
• To disconnect the most recently added
participant, press the Drop button.
6. To end the conference, press the Forced
Release button.
A .Announce the call:
• Press the Source button to return to the
caller. If you do this, use the Destination
button to return to the call recipient,
OR
• Press Cancel to drop the called
extension and return to the caller,
OR
• Press the Join button for a 3-way
conference.
5. To complete the call direction, hang up or
press the Release button,
OR
To disconnect all parties, press the Forced
Release button.
- Join -
Use this feature to connect yourself and two
outside or inside participants.
1. Make the first call (see Making Calls, p. 10).
2. Press the Start button.
3. Dial the next number (including the dial-out
code) or extension.
4. Press the Join button.
5. To drop out of the conference, press the
Release button,
OR
To end the conference, press the Forced
Release button.
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Call Handling
- Unsuccessfully Directed Calls -
- Returning Calls -
If you dial incorrectly or reach an extension
that is busy or unavailable, you can do one of
the following:
• Press the Cancel button to return to the
Some of the calls you receive are returning
calls. These are calls you or another operator
directed to co-workers. If the co-worker you
directed the call to is unavailable (away from
the telephone or on another call, for
example), the call may return to you for
further handling, depending on how your
system is set up.
• Try the call again.
• Take a message from the caller. See
Messaging (pp. 13–16) for further
information.
The following are examples of returning calls:
• Directed call (a call sent to an inside or
outside telephone)
• Directed call camped-on at the
destination telephone
• Held call
Camp-On (p. 21)
Paging (p. 22)
Park (p. 22)
When a call returns, you can either attempt the
call again or take a message from the caller.
See Messaging (pp.13–16) for further
information.
Note: Do not use Camp-On if your system is
equipped with a voice mail system.
- Responding to the Queue -
The following features can be enabled or
disabled on a QCC. See your system manager
for details on how your system is programmed.
Calls-in-Queue Alert
The Calls-in-Queue Alert feature causes your
phone to beep when a new call arrives in the
QCC queue. The system can be programmed
so that the beep can indicate each new call
arrival, every second call arrival, and so on.
Queue Over Threshold
When there are more calls in the queue than
are allowed by a programmed threshold, the
number on your console display that shows the
number of calls in the queue turns to reverse
video.
When this occurs, you can do one of the
following:
• Respond to calls more quickly.
• Contact your backup QCC operator, if
assigned, to start accepting calls.
• Notify your system manager.
Notify your system manager if callers complain
about slow response times. System options
can be adjusted to give better response times.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Messaging
Your phone system has the following features that allow you to leave messages for others in your office.
• Leave Message. If you cannot reach a co-worker, you can use the Leave Message feature to let a
co-worker with a display telephone know that you called, along with the date and time of your call. If
you leave one message and then another, the second message replaces the first.
• Send/Remove Message. Using the Send/Remove Message button on the console allows you
to turn co-workers’ Message lights on or off. Use this feature to signal co-workers with nondisplay
phones.
• Posted Message. This feature allows co-workers with display phones to know when you are
unavailable.
• Direct Voice Mail. This feature allows you to call directly to co-workers’ voice mail or to transfer
callers directly to co-workers’ voice mail.
When a message is waiting for you, your Message light is lit. The following descriptions explain how to
read, cancel, and delete messages you have sent or received.
You can use Signaling to notify co-workers when they have visitors or to provide them with information
or reminders.
- Messaging Feature Table -
The following messaging features (Feature) are available from your telephone. The recipient’s
telephone (Telephones) must be configured as indicated.
Feature
Telephones
Screen/Button
Leave Message
Posted Message
Send/Remove Message
Direct Voice Mail
Signaling
Display
Display
All
With Voice Mail
Multiline
Your Extension
Home Screen. See p. 16.
Menu Screen. See p. 16.
Send/Remove Message button. See p. 14.
DSS Button. See p. 15.
See Signaling, p. 15.
Menu Screen. See p. 15.
Receive Message
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Messaging
- Send/Remove Message -
Press the Send/Remove Message button on your console to turn the Message light on or off for
any telephone in your system.
For co-workers with display telephones, the Send/Remove Message feature turns on Message lights
and also delivers the message: ATT OPERATOR (ATT means attendant) or displays your name, if
programmed, the date and time you left the message, and your extension. For example: ATT RENEE
20:26 08/02 X14.
If another operator has turned a co-worker’s Message light on with Leave Message, using Send/Remove
Message turns that co-worker’s Message light off. To make sure that you don’t accidentally turn off a co-
worker’s Message light that should remain on, use the Message Status button on the DSS to see if the
red light next to the button for your co-worker’s extension is on before you use Send/Remove Message.
When you use the Message Status button, the light at the DSS button reflects the status of
operator-sent messages only. If a co-worker’s Message light is on because a fax is waiting
or another co-worker has left a message, the DSS button light is not on and using Send/Remove
Message does not turn the co-worker’s Message light off.
To send messages (consoles without a DSS):
1. Press the Send/Remove Message button.
2. Dial the co-worker’s extension.
To send messages (consoles with a DSS):
1. Press the Message Status button on DSS.
The green light next to Message Status goes on.
2. Check the light next to the DSS button for the person’s extension. If necessary, use the Page
buttons to locate the extension.
• If the red light is on:
Press the Message Status button to return to call handling. If you use Send/Remove Message,
you turn off the co-worker’s Message light and cancel other operator-sent messages on the
display.
• If the red light is off:
Press the Send/Remove Message button.
Press the DSS button. The red light next to the DSS button for the co-worker’s extension goes on,
and the co-worker’s Message light goes on, indicating that an operator-sent message is waiting.
Press the Message Status button to return to call handling.
To turn off Message lights (consoles with a DSS):
1. Press the Message Status button on the DSS.
The green light next to Message Status goes on.
2. Check the light next to the DSS button for the person’s extension. You can use the Page buttons to
locate the extension.
3. If the red light is on:
Press the Send/Remove Message button.
Press the DSS button.
The red light next to the DSS button for the co-worker’s extension goes off, and the co-worker’s
Message light goes off, and the operator-sent message is deleted.
4. Press the Message Status button to return to call handling.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Messaging
- Signaling -
- Receiving Messages -
Use Signaling to notify co-workers when they
have visitors or to provide them with
information or reminders. You can signal
multiline telephones only. You must have a
DSS attached to your console.
You and your co-workers can prearrange the
signals. For example, you can arrange two
beeps for a visitor and three beeps for a
reminder.
When your Message light is on, you have a
message from a co-worker. Messages are
identified by the name or extension of the
caller, along with the time and date the
person called. Depending on how your
system is set up, you may also have a voice
mail message or a fax. A message may be
identified in these ways:
ATT You have a message from another
system operator.
To use Signaling:
1. Select a Call button.
2. Lift the handset, press the Speaker button,
or use the headset.
You hear a dial tone.
3. Press the Forced Release button.
The light next to the selected Call button
goes off.
FAX You have a fax.
VMS You have a voice mail message.
EXT Indicates the extension number of the
person who called.
✻
Marks a new unread message.
To read and respond to messages on your
display:
1. Press the Menu button.
2. Select Messages.
3. Choose from:
4. Press the DSS button for your co-worker.
Your co-worker hears a beep each time you
press the DSS button.
5. Hang up.
• Return Call to call your co-worker or
voice mail while reading the message.
• Next Msg to see the next message.
• Delete Msg to delete the message. You
can have up to 10 messages; if there are
10, no more are accepted.
- Direct Voice Mail -
If your company has voice mail, this feature
allows you to dial a co-worker’s voice mailbox
without calling that person. Direct Voice Mail
is especially useful for transferring calls when
a co-worker is not available. Usually, you
activate the feature as soon as you lift the
handset or press the Speaker button to make
a call, or while on a call that you want to
transfer to a voice mailbox. (You don’t have to
use the Start or Transfer button.) You can
extension; just do Step 1 below.
1. Press Direct Voice Mail button on the
DSS (p. 2),
OR
Press Feature button and select Direct VM.
2. Dial the extension for the voice mail
recipient or press the DSS button.
Note: If you transfer a call to an extension
that has no voice mail, you hear an error tone
and the call returns to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Messaging
- Leaving Messages -
- Posting Messages -
If you cannot reach a co-worker, you can take
a message from a caller and use the Leave
Message feature to leave a message for the
co-worker if the co-worker has a display
telephone.
To use Leave Message, you must be on the call
your co-worker does not have a display, you
see Cannot Send Message on your display. In
this case, use Send/Remove Message (p. 14)
instead.
A posted message appears on the display of
any inside caller who tries to reach you, as
long as that person has a display phone. (You
also see the message posted at your own
phone as a reminder.) There may be as many
as 20 messages available to you for posting.
Message 1 is always DO NOT DISTURB*; the
others may include such choices as: OUT TO
LUNCH, OUT SICK, IN A MEETING, depending
on how your system manager has programmed
them.
To post a message:
1. Press the Menu button.
2. Select Posted Msg.
3. Select the message you want to post.
4. Select Post.
When a call is unanswered or busy (you are
listening to a ringing or busy signal):
1. Select Leave Msg from the Home screen.
2. Read the status of the message on display:
• Msg Sent if message was delivered.
5. Press the Home button.
To cancel a posted message:
1. Press the Menu button.
2. Select Posted Msg.
3. Select Cancel.
4. Press the Home button.
• Message Box Full if message was not
delivered because co-worker’s message
box is full.
• Cannot Send Message if message was
not delivered (for example, because
co-worker does not have a display
telephone).
telephones; when you dial their extensions, the
messages show on your display. You can use
the Inspect feature (p. 21) to see the message as
well. This is especially useful when checking to
see if the extension has Do Not Disturb active. If
Do Not Disturb is active, the red light at that
extension is on. If the Do Not Disturb message
is posted but the red light is not on, the feature
is not active.
Your co-worker’s Message light turns on after
you leave the message.
Note: If you use Leave Message to send a
second message to a co-worker who has not
responded to your first message, the second
message replaces the first. The Message light
remains on.
* The Do Not Disturb message may be posted, but
the Do Not Disturb feature cannot be used on a
QCC. Use Position Busy (p. 23) instead.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Directories
- Extension & System Directory -
- Personal Directory -
Check with your system manager to find out
whether these directories have been
programmed. The System Directory dials
outside numbers that people in your company
call often. The Extension Directory dials
inside numbers.
1. Press the Menu button.
2. Select Directory.
3. For the Extension Directory, select Ext Dir,
OR
For the System Directory, select System Dir.
This feature stores up to 50 phone numbers
(as well as account codes, area codes, and
access codes), then dials those numbers when
you wish. You enter, change, select, dial, and
delete listings from the display. You can
access the Personal Directory from the Menu
screen. You can assign 16 entries from your
Personal Directory to appear in the Home
screens (8 per screen).
When entering or changing names, use the
screen to select letters A–F; use the line
G–Z. Select Punctuation to use the displayed
punctuation marks. You may need to use
special characters (p. 24) when entering
dialing sequences. Include dial-out codes, if
needed.
4. Select the entry.
a) Select the range of letters that
includes the first letter of the listing
you want. If there are no entries
available for the range, you hear a
beep.
b) View other entries by selecting either
Prev Page or Next Page.
c) If you want to check the number,
select Show Number and press the
button next to the name. Select Show
Number again to stop viewing
numbers.
d) To dial a number, press the button
next to the listing.
The screen guides you through Personal
Directory activities, so the steps are
summarized here. Press Home to stop the
activity. Bold type shows the button you
press; italics indicate a screen selection.
To enter a listing:
Menu→Directory→Personal Dir→Enter
New→Type name→Enter→Type number→
Enter→Yes or No→Enter→Home
To assign a listing to the Home screen
Directory option:
5. Press the Home button to exit.
Menu→Directory→Personal Dir→Put on
Home→Select a range of letters→Select
listing→ Select location on the Home
screen→Home
To dial a listing from the Home screen:
Home→Directory→ Select listing
To verify a stored phone number, use the steps
above to display the letter range, and:
Show Number→Select listing→Show Number
To delete a listing:
Menu→Directory→Personal Dir→Delete
Entry→Select a range of letters→Select
listing→ Delete→Home
To change a listing:
Menu→Directory→Personal Dir→Edit
Entry→Select a range of letters→Select
listing→Select part of listing to change→Enter
new information→Enter→Exit→Home
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Using Features
There are two ways to select features:
• Select the feature from the display.
a) Press the Home or Menu button to display the Home or Menu screen or press the Feature
button to display the Feature screen.
b) Press the unlabeled display button next to the feature abbreviation.
• Press the fixed-feature button.
The following table shows features available from the Home, Feature, and Menu screens and the
associated display abbreviations.
Feature
Button/Screen(s)
Display Abbreviation
Account Code
Alarm Clock
Feature, Home
Menu
AccountCode
Alarm Clock
Barge In
Barge In
Feature
Camp On
Feature, Home
Feature
Camp On
CanclFollow
Directory
Cancel Follow Me
Directory
Home, Menu
Menu
Extension Directory
Personal Directory
System Directory
Direct Voice Mail
Follow Me
Ext Dir
Home, Menu
Menu
Personal Dir
System Dir
Direct VM
FollowMe
Pickup Grp
Pickup
Feature
Feature
Group Pickup
Individual Pickup
Messages
Feature, Home
Feature, Home
Menu
Messages
Delete Msg
Next Msg
Return Call
Delete Message
Next Message
Return Call
–
–
–
Messaging
Leave Message
Loudspeaker Paging
Pickup
Feature, Home
Feature, Home
Feature, Home
Menu
Leave Msg
Loudspkr Pg
Pickup
Posted Message
Timer
Posted Msg
Timer
Menu
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Often-Used Features
- Account Codes -
- Alarm Clock & Timer -
In some companies you enter an account code
before or during a call to indicate client billing
information. You may be required to enter an
account code for all outside calls, or an
account code entry may be optional for
incoming and outgoing calls. Check with your
system manager for account code operation
and account codes.
Alarm Clock causes your phone to beep at a
certain time; you can set only one alarm. Until
canceled, the display shows a bell reminding
you that the alarm is on. The alarm sounds
each day at the same time.
Timer times calls or other activities for up to
59 minutes, 59 seconds, displaying the
elapsed time on your screen. You must turn
Timer off when timing is over; it does not
turn off automatically at the end of a call.
To enter an account code:
1. Select AccountCode from the Home
screen,
To set an alarm:
OR
1. Press the Menu button.
2. Select Alarm Clock.
3. For English-language operation, dial a
4-digit time from 0100 to 1259. Then select
a.m./p.m. to switch between AM and PM.
For Spanish or French operation, dial a
4-digit time between 0000 and 2359.
If you make an error, select Reset and redial.
4. Select On.
5. Press the Home button. The display shows
a bell to remind you that the alarm is on.
To cancel the alarm:
1. Repeat Steps 1 and 2 above.
2. Select Off.
Press the Feature button and select
AccountCode from the Feature screen.
2. Dial the account code and #.
3. Lift the handset or press the Speaker
button to make a call.
4. Dial the outside number (including the dial-
out code, if required).
To enter or change an account code during a
call (the other party cannot hear your entry),
follow Steps 1 and 2. If an account code is
entered for an incoming call before it arrives,
you cannot change that code during the call.
3. Press the Home button. The display no
- Alarm -
longer shows a bell.
To time a call or other activity or to turn
Timer off:
1. Press the Menu button.
If there is something wrong with the system,
the red light next to your console’s Alarm
button goes on. Report the alarm immediately
to your system manager. Press the Alarm
button, then the Inspct button, to see how
many problems the system is reporting.
2. Select Timer.
The red light stays on until the problem is
cleared by your system manager.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Often-Used Features
- Authorization Codes -
- Barge-In -
If your system manager has given you an
authorization code, you can pick up someone
else’s telephone, enter your authorization
code, and make an outside call with your own
calling privileges. You must activate the
feature and enter your code for each call you
make, even when you are adding people to a
conference. It is not necessary to use your
authorization code for inside calls. Using an
authorization code does not affect the button
assignments on your own phone or the one
you are currently using.
If a co-worker is on the phone or using Do
Not Disturb, use Barge-In to reach that
person in an emergency or if you have special
instructions to interrupt. When the extension
is busy, you hear a tone and Barge-In
connects you to the call; if your co-worker is
using Do Not Disturb, his or her telephone
rings.
You cannot use Barge-In on the following:
• A conference call if the conference
already has the maximum number of
participants. (You hear a fast busy signal.)
• Telephones that have forwarded calls by
using Coverage, Forward, or Follow Me.
(You hear ringing at the extension you
are calling.)
• Telephones that have Privacy in use.
(You hear a fast busy signal.)
• Telephones that are being programmed.
(You hear ringing at the extension you
are calling.)
• Telephones that are in the process of
dialing. (You hear a fast busy signal.)
Security Alert
Compromise of authorization codes
could lead to toll fraud or unauthorized
charges.
Memorize yourauthorizationcode,anddonot
share it with anyone.
The way you activate the Authorization Code
feature depends upon the type of telephone
you are using to make the call. You cannot
use an authorization code at a QCC.
To use:
• If the telephone has a programmed
Authorization Code button, press it.
The system selects a line and automati-
cally activates the Speaker button (an
available line button is selected for you);
then continue with Step 3 below.
Press the Feature button and select Barge In.
• On an MLX display telephone (except a
QCC), press the Feature button, then
select AuthCode [Auth] from the display
or dial 80; then continue with Step 3 below.
To enter an authorization code at any type of
phone (except a QCC):
1. Lift the handset or press the Speaker
button. (You may first select an ICOM, SA,
or SSA button.)
2. Dial #80.
3. Dial your authorization code, followed by #.
4. Dial the dial-out code (usually a 9) for an
outside call and then dial the phone number.
5. To make another call, put the call on hold or
hang up, and repeat Steps 1–4.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Often-Used Features
- Camp-On -
- Follow Me -
Use Camp-On to direct a call to a busy or
unavailable inside telephone and have the call
wait at the extension for a longer period of time
than Release allows.
You can use the Follow Me feature when a
co-worker is meeting with you or working at
your desk, or to answer incoming calls to your
co-worker's extension while he or she is away.
If the telephone is busy, the person to whom
you directed the call hears a tone, signaling
that another call is waiting. If the call remains
unanswered, it returns to you or another
operator for further handling.
If Follow Me is activated and Delayed Call
Forwarding is programmed for a forwarding
extension, calls ring at the forwarding extension
for the programmed number of rings (0–9)
before being forwarded to your extension.
To camp on a busy extension, do one of the
following:
To use Follow Me to answer calls that arrive at
a co-worker’s extension:
• Select Camp On from the Home screen.
1. Press the Feature button.
• Press the Feature button and select
2. Select Follow Me.
3. Dial the co-worker’s extension or press the
DSS button.
To cancel:
1. Press the Feature button.
2. Select CanclFollow.
3. Dial the co-worker’s extension, press the
DSS button, or use the Extension Directory.
To cancel all extensions at once:
1. Press the Feature button.
2. Select CanclFollow.
3. Dial ✻.
Camp On.
Selecting the Camp-On feature completes
directing a call. You can only do this when
manually directing a call or with manual
completion. (If you have automatic completion
and use the DSS, the call does not camp on.)
Note: Do not use Camp-On if your system is
equipped with a voice mail system.
- Inspect -
The Inspct button displays information
about calls on Call buttons or features on
fixed-feature buttons. To use it, press the
Inspct button and then press a Call or
fixed-feature button. When you finish, press
the Home button to leave Inspect mode.
With Inspect, you can:
• Press a Call button to view information
about an incoming call, held call, or
conference call.
• Press the Pool Status button to view
the status of lines in all pools.
• On a DSS, press a Page button to view
the first number in the range that is
activated by the Page button.
• On a DSS, press a DSS button to view
extension information.
• Press the Alarm button to view the
status of system alarms.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Often-Used Features
- Night Service -
- Park -
To use Park, you must have a DSS with
Night Service is used to send after-hours
outside calls to another telephone or
telephones and/or calling group. Night
Service can also be set up so that you have
to enter a password before turning Night
Service on or off.
If Night Service is not set up to turn on and
off automatically, you must turn Night Service
on when you leave for the night and turn it off
when you start your day.
programmed for park zones. Park allows you
to hold a call when the recipient can’t be
located. Use Park with Pickup (p. 23) and
Paging features so that you can locate a
co-worker who needs to take a call or pick
up a parked call. After a specific period set by
your system manager, the parked call returns
to your console or to that of another operator.
To park a call and then page:
1. While on a call, press the button
programmed with a park zone. Skip the
remaining steps if you do not plan to page.
2. Press a Call button and lift handset or use
headset.
3. To page over telephone speakers, dial the
Group Paging or Page All number or DSS
button for that number,
To turn Night Service on or off:
1. Press the Night Service button. This
toggles the feature on and off. A green
light indicates that Night Service is on.
2. Enter the password if required. You have
one minute to enter the password or you
must start the procedure again.
OR
- Paging -
Press Home button and select Loudspkr
Pg, dial Loudspeaker Paging number or
press DSS button for it. Then dial paging
zone, if necessary.
4. Announce the call and park zone extension
number where the call is held.
To pick up a parked call:
1. Press the Home button.
2. Select Pickup.
3. Press the park zone DSS button or dial the
extension number where the call is parked.
For details, see Pickup, p. 23.
Paging features allow you to page groups of
individuals over their phone speakerphones
or over the company’s loudspeaker paging
system (if there is one). Group Paging, Page
All, Loudspeaker Paging, and paging zone
numbers can be programmed on DSS buttons.
To page over phone speakerphones, check
with your system manager for Group Paging
or Page All numbers, then:
1. Press a Call button.
2. Lift the handset or use the headset.
3. Dial the Group Page or Page All extension
number, OR
Press the DSS button for one of these
numbers.
4. Make the announcement and hang up.
Ask your system manager whether Loud-
speaker Paging is available, what the number
for it is, and whether there are paging zones
for different parts of your company. Then:
1. Press a Call button.
2. Lift the handset or use the headset.
3. Select Loudspkr Pg from the Home screen.
4. Enter the paging system number. Dial the
zone to be paged, if needed.
5. Make the announcement and hang up.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Often-Used Features
- Pickup -
- Position Busy -
Use Pickup to pick up a call:
• Parked by you or another operator in a
park zone
• Parked at an extension by a co-worker
• Put on hold at an extension
• Ringing at a line or extension
• Ringing at an extension for a Pickup
group of which you are a member (ask
your system manager whether you are in
a Pickup group).
Use Position Busy when you want to prevent
most calls from ringing at your console.
When you turn on Position Busy, the only calls
that ring at your console are calls made directly
to your extension number and calls that are
sent to your extension from co-workers using
the Forward and Follow Me features. All other
calls go to another operator or to a telephone
that is a member of a calling group
programmed by the system manager to be a
backup position.
If you pick up a call for a Pickup group, you do
not need to know which extension in the group
is receiving the call.
Note: If no other operator position is available
for backup and/or if there is no Position Busy
backup programmed in your system, Position
Busy does not work.
To use Individual Pickup:
1. Press the Home button.
2. Select Pickup.
3. Dial the extension number or press the DSS
button for the extension.
To use Position Busy:
1. Press the Position Busy button to turn on
the feature.
The green light next to the button goes on.
2. Press the Position Busy button again to
turn off the feature.
The green light next to the button goes off.
OR
Dial the line number where the call is
ringing or press the DSS button for the line.
OR
Press the DSS button for the park zone.
To use Group Pickup:
1. Press the Home button.
2. Select Pickup Grp.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Special Characters
When you program Personal Directory listings, you are storing a sequence of numbers to be dialed
automatically. Some dialing sequences need special characters. For example, you press the Hold
button to insert a pause (p) after the dial-out code in a dialing sequence. This way, the system is
allowed to seize an outside line before dialing the number. A pause can also be used to separate a
phone number from an extension number.
The following table describes special characters. Ask your system manager which special characters are
needed and when to use them.
- Special Characters -
When You You
This
Means...
Press...
See...
Drop
Hold
s
Stop. Halts dialing sequence to allow the system to respond.
p
Pause. Inserts 1.5-sec. pause in the dialing sequence. Multiple
consecutive pauses are allowed.
Conf
#
f
Flash. Sends switchhook flash. Must be first entry in sequence.
#
End of Dialing. Use to signal end of dialing sequence or to separate
grouped digits.
Copyright © 1996, Lucent Technologies. MERLIN LEGEND, MLX-10D, MLX-10DP, MLX-16DP, MLX-20L, MLX-28D,
and Passage Way are registered trademarks of Lucent Technologies. Mirage, StarSet, and Supra are registered trademarks
of Plantronics, Inc.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Display Reference
Fixed Display Buttons
Menu Screen
The Menu screen lists features and functions you can use only through your display. Calling information is
not shown on the Menu screen. You can make and receive calls while in Menu mode, except when using
the Alarm Clock or Personal Directory features. You can also use Menu features while you are on a call.
To select a feature from the Menu screen, press the unlabeled display button next to it. To return to the
Home screen, press the Home button.
Fixed Display Buttons
7-Line Display
Fixed Display Buttons
Unlabeled Display Buttons
Fixed Display Buttons
Press to select the
corresponding features
and options shown on
each screen.
More
Home
Press to select specific
display screens: Home,
Inspct
Menu
Menu, More, and
Inspct (Inspect).
Home
More
MENU MODE: Select Feature
Press HOME to Exit
Directory
Press for access to
System, Extension,
and Personal Directories
(p. 17).
Menu
Inspct
Messages
Press to view or post
messages(pp. 13–16).
Posted Msg
Alarm Clock
Timer
Sys Program
Maintenance
Unlabeled Display Buttons
Unlabeled Display Buttons
Volume
Press to use alarm clock
or timer (p. 19).
Feature
Transfer
Feature Button
HFAI
Conf
Press to display the
Mute
Drop
Feature screen to select
features you use often.
If your console is set up for system
programming and maintenance, Sys
Program and Maintenance are shown
on the right side of the Menu screen.
If you have not been trained or are not
familiar with these features, see your
system manager.
Speaker
Hold
Note: If your company has Caller ID services and Caller ID is supported in a caller’s area, an outside
caller’s phone number may appear on your display when an outside call comes in or is transferred to
you. When caller information is not available because of the caller’s local phone company or because
the caller has blocked the service, you may see No Caller ID, Out of Area, or Private.
Inspect Screen
The Inspect screen has five functions:
• To display information about Call buttons and fixed-feature buttons
• To enable you to view the status of system alarms and the number of busy trunks in a pool
• To display the extension and message status of DSS buttons
Home Screen
The Home screen, as shown in the following illustration, is displayed when you're not using your console's
features. Screen information changes when you receive or make a call and use features.
To return to the Home screen at any time, press the Home button.
• To display Busy/Do Not Disturb status using DSS buttons
• To view call-handling information when you're on a call, have other calls on hold, or are on a conference
You cannot inspect information about dedicated feature buttons, the unlabeled display buttons, or the fixed
display buttons. If you are in Inspect mode and you press Home, Menu, or a dedicated feature button, your
console is no longer in Inspect mode.
When the phone is idle, this screen
shows a posted message, if any.
When the phone is idle,
shows date and time.
It also displays Alarm
Clock and Timer (p. 19)
if either is set.
When a call comes in or is made,
this screen shows the number
called, name or number of the
caller, or other call-handling
information.
Home
Menu
More
Inspecting a Fixed-Feature Button
To view fixed-feature button information, press the Inspct button, then press a feature button.
• For Start, Headset/Handset Mute, Send/Remove Message, Position Busy, Release, Headset
Status, Night Service, Cancel, Join, Headset Auto Ans, or Forced Release, the feature name
appears on the display.
• For either Source or Destination, when a call is on hold on the button, the button name and calling
information about the held call appear.
• For Alarm, the display shows the number of alarms in your system.
• For Pool Status, the number of trunks in each pool and the number of trunks in use appear.
Inspct
MAR 01 1:55
Out To Lunch
Press to leave a message
for a user with a display
phone (p. 16).
Press to enter an
account code before
or during a call
(p. 19).
Leave Msg
Pickup
AccountCode
Directory
Camp On
Press to pick up a call
ringing at another extension
or at a specific line, but not
at your phone or to pick up
a call parked at a parking
zone (p. 23).
Press for access to
System, Extension,
and Personal
Press to camp on at
a busy extension (p. 21).
Directories (p. 17).
25
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Display Reference
Feature Screen
Inspecting a Call Button Screen
The Feature screen provides quick access to the features used most often. As you handle operator tasks, the
Feature screen tells you which features are available to help you. The features on this screen change
depending on your tasks.
Complete calling
information about the
call on the specific
button you're inspecting.
Home
More
FX-NAME
19075551212
Menu
Inspct
Home
Menu
More
Trk9111
4
Select a Feature
Press to pick up a call
ringing at another
extension or at a line
(p. 23).
Inspct
5
Press HOME to Exit
INSPECT MODE
Press to send calls
from another
3=FX-NAME
2=
5=CONF: 5
4=FORWARD
Pickup Grp
Pickup
Follow Me
CanclFollow
extension to this
extension (p. 21).
1=Return
Loudspkr Pg
AccountCode
The number of calls waiting
in your queue (first number)
and the number of calls waiting
in the system queue (second
number).
Direct VM
Press to enter an
account code before
or during a call
(p. 19).
Press to call a voice
mailbox (p. 15).
Abbreviated information about
the call on each Call button.
(The numbers correspond to the
numbers on the Call buttons.)
Feature Screen Options
Your Console
Feature Displayed
Display
Is not busy or has an inside
dial tone
Group Pickup
Pickup
Loudspeaker Page
Account Code
Follow Me
Cancel Follow Me
Direct Voice Mail
Pickup Grp
Pickup
Loudspkr Pg
AccountCode
Follow Me
CanclFollow
Direct VM
Inspecting a Conference Screen
Press the Call button where the conference is taking place to display conference information.
The number of people on
the conference call.
Home
Menu
More
Conference: 5
Trk9111
Inspct
Has reached a busy extension
Barge-In
Leave Message
Camp-On
Barge In
Leave Msg
Camp On
4
5
INSPECT MODE
* PIERRE
The number of calls waiting
in your queue (first number)
and the number of calls
waiting in the system queue
(second number).
FX-OSLO
FX-LA
Is ringing at an extension or
connected to an inside call
Leave Message
Barge-In
Camp-On
Direct Voice Mail
Leave Msg
Barge In
Camp On
Direct VM
MARIA
ANITA
Is connected to an outside line
Camp-On
Account Code
Follow Me
Camp On
AccountCode
FollowMe
Indicates the call that will
be dropped when the
Drop button is pressed.
Cancel Follow Me
Direct Voice Mail
CanclFollow
Direct VM
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes & Reminders
Account Code Entry
■ Required
■ Optional
Automatic/Manual Completion
■ Automatic Completion
■ Manual Completion
Queue Over Threshold
■ No
Automatic Hold/Release
■ Automatic Hold
■ Yes, give number of calls in queue
■ Automatic Release
for alert __________________
Pools
■ No
Night Service
■ No
■ Yes
Automatic On/Off
■ No
■ Yes
Password
■ No
■ Yes
■ Yes, list numbers
______ ______ ______ ______
______ ______ ______ ______
Direct Station Selector
■ No
■ Yes
Page 1 range ______ to ______
Page 2 range ______ to ______
Page 3 range ______ to ______
Automatic Hold/Release
■ Automatic Hold
■ Automatic Release
Dial-Out Code
■ No
■ Yes, code ___________________
Park Zones
■ No
■ Yes, list extensions
______ ______ ______ ______
______ ______ ______ ______
QCC Backup
■ No
■ Yes, calling group _____________
Voice Announce
■ Enabled
■ Disabled
Calls-In-Queue
(Tone when calls enter your queue.)
■ No
■ Yes
Delayed Call Forwarding
■ No, (0 rings)
■ Yes, number of rings Forwarding
is delayed (1–9 rings) _______
Download from Www.Somanuals.com.2A7ll Manuals Search And Download.
Notes & Reminders
PAGING NUMBERS
Paging Group(s)
No. Loudspeaker Paging
No.
Line Number
Zone 1
Zone 2
Zone 3
Zone 4
Page All
COVERAGE/PICKUP/CALLING GROUPS
Group Name
No. Group Name
No.
ADDITIONAL NUMBERS
Name
No. Name
No.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
|