Lucent Technologies Marine Radio 518 456 151 User Manual
PARTNER® Advanced  
Communications System  
System Planner  
518-456-151  
Issue 1  
November 1997  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Introduction  
Setup decisions for the PARTNER Advanced Communications System (ACS)  
should be recorded on the forms in this Planner. The forms must be filled out  
before installation to provide guidance for the technician who installs and  
programs the system.  
®
2. Provide advice to help the customer fill out any additional forms needed for  
installation.  
■ If button features should be programmed onto users’ telephones cen-  
trally (instead of letting users do it themselves), the desired button  
programming should be specified using the appropriate telephone  
templates or feature checklists on Form C1 through Form C8.  
The forms should also be used by the customer to record changes after  
installation, so there is an ongoing record of the programming for the system. If  
programming is inadvertently erased (for example, in the event of an extended  
power failure) and a backup of system programming is not available, the forms  
can be used to reprogram the system.  
■ If the customer plans to use dialing restrictions, Form D should be  
used to specify a list of Emergency Phone numbers that will override  
restrictions. Form D can also be used to specify lists of Disallowed  
and Allowed numbers to fine tune the dialing capabilities for individual  
extensions, to identify External Hotline phones that dial a specified  
telephone number as soon as the handset is lifted, and to specify up  
to 99 account codes for account code verification.  
Identifying a System Manager  
As part of the planning process, the customer should identify a person in the  
company to act as System Manager. The System Manager is the person who  
is responsible for the telephone system. The System Manager should work  
with you to fill out the forms, and should participate (with an alternate) in the  
training for the system. The System Manager can then provide training, answer  
questions for telephone users, and perform programming for the system after  
installation.  
■ If the customer wants System Speed Dial numbers programmed that will  
be available to all system users, Form E should be filled out.  
After the forms are completed, take the original and leave a copy with the  
customer.  
Customer Training  
Filling Out Planning Forms for the Customers  
The planning forms were designed to be as self explanatory as possible. The  
first few times you fill out the forms, it may help to refer to the supplemental  
instructions on the pages that follow. For detailed information about system  
features, see the PARTNER Advanced Communications System Programming  
and Use guide.  
In the U.S., a Lucent Technologies representative will provide training at the  
customer’s place of business when the system is installed and programmed.  
(Outside the U.S., customers should contact their Lucent Technologies Repre-  
sentative or local Authorized Dealer for information about training.) The repre-  
sentative will demonstrate how to:  
■ Handle calls and use system features  
We suggest you complete the forms as follows:  
■ Program features and phone numbers onto phone buttons  
■ Change the programming for the system and for individual telephones  
■ Use the Quick Reference cards and the Programming and Use guide  
To prepare for training, please tell the customer to:  
1. Fill out Form A (to describe the customer’s overall system configuration)  
and Form B1 (to record basic information for each system extension).  
If you want to customize extension settings for different users, complete  
Form B2 as well.  
■ Set aside approximately two hours of uninterrupted time for training on  
NOTE: For system options that require programming, the forms show the  
name of the procedure and the programming code in the form {#NNN} (for  
example, Line Assignment {#301}); centralized programming procedures  
for individual extensions are identified by the letters {CTP} for “Centralized  
Telephone Programming” (for example, Line Ringing {CTP}).  
installation day, preferably in a quiet place away from distractions.  
■ Designate one person (generally the System Manager) and an alternate to  
participate in the training. These persons will then train the rest of the  
company staff.  
This training will ensure that the customer takes maximum advantage of their  
new system. Thank you for your cooperation.  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
2
Form A Supplemental Instructions:  
System Configuration  
Salesperson completes items 1–12.  
Sales Support Representative completes items 13–15.  
VMS-AA  
ASA  
Automated Attendant service of PARTNER MAIL™ or  
PARTNER MAIL VS™, which must be purchased separately.  
If the receptionist does not answer an incoming call, VMS-AA  
lets the caller select an extension or route. Programmed using  
option 1 of Group Call Distribution {#206} for Hunt Group 7.  
6. Configure Hardware for Hybrid Mode  
Check “Yes” if the customer wants line pooling capabilities; otherwise check  
“No.” This feature is available only if you are using PARTNER ACS R2.0 or  
later.  
Automatic System Answer (ACS R2.0 or later only) plays  
a recorded message, then places the call on hold, disconnects  
the call, or continues to ring available extensions.  
By default, the system is configured for Key mode. Changing to Hybrid mode  
requires Lucent Technologies Authorized Personnel to administer the system at  
installation.  
Hunt Group Hunt Group sends incoming calls directly to an extension in  
the specified group 1–6. Programmed using option 1 of Group  
Call Distribution {#206}.  
IMPORTANT: In the U.S., a PARTNER ACS system installation for Hybrid  
mode requires Federal Communications Commission (FCC) registration informa-  
tion to be reported to the customer’s local telephone company. This includes the  
system’s operating mode (MF for Hybrid mode) and its FCC registration number,  
which can be found on the right side of the primary carrier. Although it is the  
customer’s responsibility to report FCC registration information, it is highly  
recommended that you report this information for the customer.  
VMS-Mail  
Voice Mail coverage of personal line by PARTNER MAIL® or  
PARTNER MAIL VS®, or the PARTNER Voice Messaging PC  
Card which must be purchased separately. Sends unanswered  
incoming calls directly to the line owner’s mailbox.  
NOTE: You can use option 3 of Group Call Distribution {#206}  
or Line Coverage Extension {#208} to specify VMS-Mail lines  
for ownership. With the #206 option, calls are routed to the  
user’s voice mailbox after four rings. The #208 option provides  
more flexibility because calls are routed after the number of  
rings specified with VMS Cover Rings {#117}, if the extension  
has VMS Cover on. The user also can turn on Do Not Disturb  
to send calls on the owned line immediately to VMS coverage.  
8. System Lines  
Enter information about individual lines in the table. Be sure to list the lines  
assigned to all extensions first, followed by personal and dedicated lines.  
Write R if Rotary (Dial Pulse) Line {#201}  
Leave blank for touch-tone lines.  
Write Ext. No. for Call Cover {#208}  
Hybrid Mode Only—Write auxiliary pool 881, 882, 883, or No Pool {#207}  
The default for Hybrid mode is all lines assigned to the main pool (880). To  
create auxiliary pools, specify the auxiliary pool access code 881, 882, or  
883. To identify lines that can be assigned to pooled extensions as individual  
lines, write “No Pool.”  
(ACS R2.0 or later only) If the customer wants a user who has a personal or  
individual line to be able to activate Call Coverage for that line, identify that  
user’s extension number in this column. Programmed using Line Coverage  
Extension {#208}.  
NOTE: Only one owner can be assigned to a specific line. However, multiple  
lines can be assigned ownership of the same extension.  
Line Coverage—You can select one per line  
If desired, identify an automated answering option for incoming calls on each  
line. (If all calls on a line should be covered by a human operator, leave all  
line coverage columns blank for that line.) To avoid confusing callers, it is  
recommended that only one of the following options be used to handle  
incoming calls throughout the system.  
Write User’s Name for Personal or Owned Line  
or Identify Equipment for Dedicated Line  
For a personal, owned, or dedicated line, write the user name or equipment  
description (for example, “Fax”); otherwise, leave blank. (If another user  
provides backup call coverage on the line, note the name of that user in  
parentheses.) Use Form B2 to record custom extension assignments.  
AA  
Automated attendant, which must be purchased separately.  
DXD  
Direct Extension Dialing (ACS R2.0 or later only) lets callers  
dial extensions without waiting for the receptionist.  
Check if Caller ID Service  
Check this column to indicate lines on which local telephone company Caller  
ID service is provided. For dial-code features that support this service, see  
Form C.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Star Code Dial Delay {#410}  
9. System Settings  
Receptionist answers calls during business hours?  
If “Yes,” be sure to record settings on these forms that will allow  
the receptionist to answer the phone before automatic coverage is applied.  
Contact the local telephone company to determine whether there is a delay  
after a star code is dialed, but before returning a second dial tone as a  
prompt for the user to enter more digits. Write in the number of seconds  
(1–5) to match the delay interval in the space provided.  
Number of Lines {#104}  
Music on Hold {#602}  
This programming procedure should be used only for installation—using it  
later erases custom settings for all extensions. After installation, use Line  
Assignment {#301} to assign lines and Pool Extension Assignment {#314}  
(ACS R2.0 or later only) to assign lines to pools.  
If Music on Hold is Not Active or no audio source is connected, callers on  
hold hear silence.  
10. Line Coverage  
DXD  
(ACS R2.0 or later only) If DXD was specified in Item 8, you can change the  
number of times that the phone should ring before the system answers. You  
must specify the message callers hear when the system answers. Be sure to  
specify a Direct Extension Dial Button {#113} for extension 10 on Form C to  
activate this feature.  
Transfer Return Rings {#105}  
The transfer return extension is identified on Form B1, Write Transfer Return  
Ext. No. {#306}.  
Outside Conference Denial {#109}  
To prevent all users from conferencing with more than one outside party,  
write “No” in the space provided.  
Call Coverage Rings {#116}  
VMS-AA  
Covered extensions are identified on Form A, Write Ext. No. for Call Cover  
{#208}. This feature is available only if you are using PARTNER ACS R2.0 or  
later.  
If VMS-AA was specified in Item 8, you can change the number of times that  
the phone should ring before the voice messaging system answers. You also  
can specify that the system should answer only when Night Service is off  
(Day only) or when Night Service is on (Night only). If Day only or Night only  
is selected, be sure to specify a Night Service Button {#503} for extension 10  
on Form C to activate this feature.  
VMS Cover Rings {#117}  
This feature applies to all intercom calls, transferred calls (that is, outside  
calls transferred by VMS-AA and inside transferred calls), and outside calls  
on owned lines (those specified using Line Coverage Extension {#208}) for  
extensions that have VMS Cover or Automatic VMS Cover {#310} active.  
ASA  
(ACS R2.0 or later only) If ASA was specified in Item 8, you can change the  
number of times that the phone should ring before the system answers and  
indicate how the system should handle the call after the greeting plays. You  
must specify the message callers hear when the system answers. Be sure to  
specify an Automatic System Answer Button {#111} for extension 10 on  
Form C to activate this feature.  
Ring on Transfer {#119}  
If Ring on Transfer is Not Active, callers hear silence unless Music on Hold is  
activated and an audio source is connected to the processor module.  
Toll Call Prefix {#402}  
If dialing a “0” or “1” to make long distance calls is not required, write “No” in  
the space provided.  
System Password {#403}  
Whoever knows the password can place any type of call at any time,  
regardless of dialing restrictions.  
NOTE: If a System Password is programmed, it must be entered to turn Night  
Service on and off. Also, users at Night Service Group extensions must enter  
the password before placing outside calls—except Marked System Speed Dial  
numbers and numbers on the Emergency Phone Number List.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
ASA/DXD PC Card (Release 2.0 or later only)  
Check this box if the customer purchased the optional ASA/DXD PC Card to  
store Automatic System Answer and Direct Extension Dial messages.  
11. Auxiliary Equipment (System)  
Check boxes that apply for auxiliary equipment connected to the control unit or  
to system wiring. All appropriate hardware and software must be purchased  
separately.  
PARTNER Voice Messaging PC Card (Release 1.1 or later only)  
Check this box if the customer purchased the optional PARTNER Voice  
Messaging PC Card to provide messaging features (store personal  
greetings, and store and retrieve messages) for up to four mailboxes.  
Battery Backup  
In some countries, battery backup is available to allow the customer to  
connect an external battery to keep the complete system operational during  
a commercial power failure. If it is available and the customer wants battery  
backup, check this box.  
Caller ID Devices  
If the customer wants to connect a Caller ID device (such as a PC to  
process Caller ID information) directly to a system line, check this box.  
A separate wiring run is required to connect each device directly to the  
network interface jack for a line.  
Loudspeaker Paging  
If the customer wants a loudspeaker paging system, check this box. If the  
loudspeaker paging system supports multiple zones, indicate the number of  
zones.  
Magic on Hold  
If the customer wants Magic On Hold, check this box. Magic On Hold  
includes a one year license that must be renewed annually.  
Uninterruptible Power Supply  
If the customer cannot afford to lose full communications capability during  
power outage, an uninterruptible power supply (UPS) should be ordered.  
SMDR  
If the customer wants to track phone usage in a printed report, check this  
box. Before changing SMDR Output Format {#610} to 24 digits, check the  
documentation for the call accounting device to verify that 24-digit output is  
supported.  
PARTNER Contact Closure Adjunct  
If the customer wants a Contact Closure Adjunct, check this box.  
Backup/Restore PC Card  
If the customer wants to be able to back up system programming, check this  
box. (The Backup/Restore PC Card is included with the PARTNER ACS  
processor module when the system is purchased in the United States or  
Canada; otherwise, it can be purchased separately.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Form B1 Supplemental Instructions:  
System Extensions  
This form provides basic information for each system extension. To customize  
line restrictions or other extension settings, you must also use Form B2.  
NOTE: In addition to the VMS extensions, you must specify an extension (with  
no lines assigned) where a remote maintenance device is installed. Write  
“VMS-RMD” in the Write Name/Description column.  
Write Name/Description  
These VMS extensions should be checked on Form B2, Identify Group  
Assignments, VMS Only. They must be assigned to Hunt Group 7 using Hunt  
Group Extensions {#505}.  
Write a user name or a description for auxiliary equipment (such as “Fax” or  
“VMS”) to be installed at the extension. If system display phones should show the  
name/description of the caller for internal calls, write the 20 characters you want  
to display, check the Check if Ext. Name Display {CTP} column, and complete  
Form B1, page 3 of 3. (MLS-model phones display only 12 characters.)  
PARTNER MAIL VS  
Check the 2 or 4 extensions used for PARTNER MAIL VS and write “VMS” in  
the Write Name/Description column. Note that the PARTNER MAIL VS module  
is installed in a carrier slot, and so takes up 6 extensions.  
Only the bottom 2 or 4 extensions, however, answer VMS calls—the other  
extensions can be used as guest mailboxes.  
Identify Telephone Attached to this Extension  
Check the appropriate column to indicate the type of phone.  
If a system and standard phone are combined on an extension, check the two  
appropriate Identify Telephone columns. If a phone and an auxiliary device are  
combined on the extension, check the appropriate Identify Telephone and  
Identify Auxiliary Equipment columns.  
These VMS extensions should be checked on Form B2, Identify Group  
Assignments, VMS Only. They must be assigned to Hunt Group 7 using Hunt  
Group Extensions {#505}.  
PARTNER Voice Messaging PC Card  
When the PARTNER Voice Messaging PC card is installed, virtual extensions  
86 and 87 are automatically assigned to the two voice ports on the PARTNER  
Voice Messaging system. Virtual extensions 86 and 87 are also assigned to  
Hunt Group 7 and any previous assignments for Hunt Group 7 are  
automatically erased.  
Identify Auxiliary Equipment  
Attached to this Extension  
Except as noted, check the appropriate column to indicate the type of auxiliary  
equipment.  
Call Waiting {#316}  
Extra Alert  
(Standard phones only) By default, the system’s Call Waiting feature is set for  
Not Active. To change the default, check extensions with standard phones  
that are to receive a tone while on a call to indicate a second incoming call.  
Check the extensions to which an extra alert, such as a light, is connected.  
IROB  
Check the extensions to which an In-Range Out-of-Building protector is  
connected to prevent electrical surges.  
External Hotline {#311}  
Check the extensions to be used as External Hotlines. Specify the telephone  
number that is dialed automatically from each External Hotline on Form D.  
AA Extension {#607}  
Check the extensions to which automated attendants are connected.  
Hotline {#603}  
Contact Closure Group {#612}  
Identify the extensions that can activate Contact Closure 1 and Contact Closure 2.  
Write “Hotline” in the Write Name/Description column and write “T” for touch-  
tone or “R” for rotary in the Standard column (under Identify Telephone) to  
indicate the phone type. (A hotline extension should have a standard touch-  
tone or rotary phone; a hotline alert extension can have any phone type.)  
PARTNER MAIL  
Check the 2, 4 or 6 extensions used to connect the PARTNER MAIL system  
and write “VMS” in the Write Name/Description column.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Write Transfer Return Ext. No. {#306}  
By default, a transferred call returns to the originating extension if the call is not  
picked up. To specify a different transfer return extension, write the extension  
number in this column. For extensions to which you are connecting a PARTNER  
MAIL system, PARTNER MAIL VS system, PARTNER Voice Messaging (virtual  
extensions 86 and 87), or auto attendant, indicate a transfer return extension—  
usually extension 10—where a person can pick up calls that are transferred by  
the VMS or AA extension but not answered.  
If DXD line coverage is used (see Form A), you also should specify a transfer  
return extension for extension 10 to provide backup coverage for calls that are  
not answered at extension 10 or at an extension that the caller selects.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Form B2 Supplemental Instructions:  
Customized Extension Settings  
Each row on Form B2 specifies settings—including group assignments—that  
can be copied to other extensions using Copy Settings {#399}. Default settings  
are shown at the top of Form B2.  
calls are not answered, write “A” (Assigned) in this column. To program a  
VMS Cover button to turn coverage on and off at an extension, see Form C.  
Voice Interrupt on Busy {#312}  
(System phones only) To identify an extension as being eligible for Voice  
Interrupt on Busy calls while busy with another intercom or outside call, write  
“A” (Assigned) in this column.  
Settings for Auxiliary Equipment  
The following settings may be useful for auxiliary equipment:  
■ For a dedicated line (such as a Fax line, see Form A), assign the line to the  
Line Access Mode {#313}  
equipment extension and remove it from other extensions.  
If the system has been set up for Hybrid mode, all extensions (except 10)  
operate as pooled extensions by default. To identify extensions that are to  
operate as key extensions, write “K” (Key) in this column. Extension 10  
always operates as a key extension.  
■ To prevent other extensions from interrupting calls, write “A” (Assigned) in  
the Automatic Extension Privacy {#304} column.  
■ In general, do not assign auxiliary equipment extensions to a Pickup Group,  
Calling Group, Hunt Group, or Night Service Group.  
Hybrid Mode Only—List individual lines {#301}  
For pooled extensions, list line numbers to identify individual lines to be  
assigned to extensions. By default, all lines are assigned to extension 10.  
Identify Extension Settings if Different from  
Default  
For each extension, identify extension settings that are different from the default.  
Line Ringing {CTP}  
Display Language {#303}  
(System display phones only) Indicate the language for display messages if  
different from English.  
The default is immediate ringing for all individual lines at all extensions. For  
pools, the default is no ring. For each extension, specify the lines or pools that  
should ring immediately, after a delay (about 20 seconds), or that should not  
ring. Also specify the lines or pools that should not be assigned.  
Automatic Extension Privacy {#304}  
By default, any user sharing a line can join calls at another extension  
(Privacy is Not Assigned). If all calls are to be private, write “A” (Assigned) in  
this column. Always use this feature for Fax and modem extensions.  
Settings for a Receptionist’s Extension  
If a receptionist at extension 10 is to answer calls, coordinate line assignments  
and line ringing for extension 10 with settings for other extensions, to deter-  
mine how incoming calls are handled.  
Abbreviated Ringing {#305}  
(System phones only) By default, a new call rings only once when a phone is  
in use (Abbreviated Ringing is Active); the line button light flashes until the  
call is answered or the caller hangs up. To change the default so a new call  
rings repeatedly, write “NA” (Not Active) in this column.  
■ If the receptionist is to answer all calls (immediate call handling), assign  
all lines to extension 10 with immediate ringing; assign lines or pools as  
needed to other extensions with no ringing. The receptionist will answer all  
calls and transfer them to the appropriate extensions. If you want another  
extension to provide backup coverage for the receptionist, assign all lines  
to that extension with delayed ringing.  
Forced Account Code Entry {#307}  
(System phones only) If a user should be required to enter an account code  
before placing an outside call, write “A” (Assigned) in this column.  
Distinctive Ring {#308}  
In Hybrid mode, immediate call handling is the factory setting for extension  
10. (Lines are assigned to individual line buttons on the phone at extension  
10 and all pools assigned to users’ extensions are set to no ring.)  
(Standard devices only) By default, outside, intercom, and transferred calls  
each have their own ringing pattern (Distinctive Ringing is Active). To change  
the default so that all calls ring the same, write “NA” (Not Active) in this column.  
■ If the receptionist is to answer calls only when users do not pick up immedi-  
ately (delayed call handling), set lines or pools to immediate ringing at  
users’ extensions and to delayed ringing at extension 10.  
Automatic VMS Cover {#310}  
If PARTNER MAIL, PARTNER MAIL VS or PARTNER Voice Messaging PC  
Card is installed and an extension should automatically be covered when its  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
8
Calling Group Extensions {#502}  
A user can ring or page (voice signal) all extensions in a Calling Group simul-  
taneously or transfer a call by ringing the group. Once an extension answers, the  
ringing or paging stops at the other extensions in the group. Do not assign  
extensions connected to auxiliary equipment, PARTNER MAIL, PARTNER MAIL  
VS, PARTNER Voice Messaging or External Hotlines to a Calling Group.  
Identify Restrictions/Permissions  
Specify restrictions and permissions for each extension.  
Line Access Restriction {#302} or  
Pool Access Restriction {#315}  
By default, access to all lines and pools is set to No Restriction. To change  
the default, write the line numbers or pool access codes in the appropriate  
columns, as follows:  
If a loudspeaker paging system is connected and Simultaneous Paging is  
desired, put all desired system phones with speakers in Calling Group 1.  
Outgoing only – User can place outside calls and receive only  
transferred calls on specified line or pool.  
NOTE: When the user voice signals an extension that has a system phone,  
the phone beeps and the user’s voice is heard through its built-in speaker.  
System phones are the only ones that can be voice signaled.  
Incoming only – User cannot place outside calls but can receive calls  
on specified line or pool.  
Hunt Group Extensions 1–6 {#505}  
No Access  
–
User cannot place or receive outside calls on  
specified line or pool (but can receive transferred  
calls, pick up calls on hold, or join calls in Key mode  
and on key extensions in Hybrid mode).  
Calls can ring or be transferred to the first non-busy extension in a Hunt  
Group. A call rings at an extension in a Hunt Group three times; if it is not  
answered, it hunts to the next non-busy extension, continuing until someone  
answers or the caller hangs up. (If you voice signal a Hunt Group, only the  
first extension is signaled; the call does not keep hunting if there is no  
answer.) Incoming calls on specific lines can be directed to a Hunt Group  
using Group Call Distribution {#206}. Do not put PARTNER MAIL or  
PARTNER MAIL VS extensions in Hunt Groups 1–6.  
NOTE: Pool Access Restriction for key extensions in Hybrid mode is set to  
No Access. Pooling and Hybrid mode are available only if you are using  
PARTNER ACS R2.0 or later.  
Outgoing Call Restriction {#401}  
Write “IN” or “LOC” to indicate restrictions for all outgoing calls on all lines at  
that extension, as follows:  
VMS Only (Hunt Group 7)  
For extension where PARTNER MAIL or PARTNER MAIL VS is connected,  
check this box to assign the extension to Hunt Group 7. For PARTNER Voice  
Messaging, virtual extensions 86 and 87 are automatically assigned to Hunt  
Group 7 and no system programming is required (any previous assignments  
for Hunt Group 7 are automatically erased). The system recognizes any  
extensions assigned to Hunt Group 7 as Voice Mail Service (VMS—  
PARTNER MAIL, PARTNER MAIL VS, or PARTNER Voice Messaging)  
extensions. Do not assign any extensions other than VMS extensions to Hunt  
Group 7. Also, do not assign PARTNER MAIL, PARTNER MAIL VS, or  
PARTNER Voice Messaging extensions to any other Hunt Groups, to any  
Calling or Pickup Groups, or to the Night Service Group.  
IN  
– User can make only intercom calls to other system extensions.  
LOC – User can make only intercom and local outside calls (no calls that  
require a “0” or “1” prefix).  
Any available outside lines can still be used to dial numbers on an Allowed  
Phone Number List assigned to the extension, numbers on the Emergency  
Phone Number List, or Marked System Speed Dial numbers.  
Identify Group Assignments  
To assign extensions to any of the following groups (each extension can be in  
one or more groups), write the group number or place a check mark in the  
appropriate columns.  
Night Service Group Extensions {#504}  
Pickup Group Extensions {#501}  
Check this box if the extension should be in the Night Service Group. When Night  
Service is on, incoming calls on assigned lines or pools ring immediately at the  
extensions in the Night Service Group, even if Line Ringing for those extensions is  
set for “delayed ring” or “no ring.” Do not put PARTNER MAIL, PARTNER MAIL  
VS or PARTNER Voice Messaging extensions in the Night Service Group.  
Any extension can answer an intercom, transferred, or outside call ringing at  
an extension in the Pickup Group, without knowing which extension is ringing  
and without being in the group. Do not put PARTNER MAIL, PARTNER MAIL  
VS or PARTNER Voice Messaging extensions in a Pickup Group.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Form C Supplemental Instructions:  
Button Templates  
There are eight pages to Form C—one page for each type of system phone and  
one page for an Intercom Autodialer. Use Form C to record line and pool button  
assignments and to indicate programming for system telephone buttons that do  
not have lines or pools assigned if the programming is to be performed from  
extension 10 or 11 during system installation. After installation, users can program  
additional features using the instructions on their Quick Reference Cards.  
PARTNER-6 Telephone  
3
1
4
2
MLS-34D Telephone  
17  
13  
9
18  
14  
10  
6
19  
15  
11  
7
16  
12  
8
A telephone button can be programmed as a line button (to access an outside  
line), as a pool button (to access a pool), as an Auto Dial button (to dial a phone  
number or a PBX/Centrex feature access code with one touch), or as a dial-code  
feature button (to access a dial-code feature with one touch). Line and pool  
buttons must have status lights; some features also require buttons with lights  
(see “Button Feature Summary”).  
5
1
2
3
4
MLS-18D, MLS-12D®, and MLS-12® Telephones  
13  
9
5
14  
10  
6
15  
11  
7
16  
12  
8
Using the information from Line Ringing and Line/Pool Access Restriction on  
Form B2, fill out Form C as follows:  
1
2
3
4
NOTE: On MLS-12D and MLS-12 telephones, only buttons 1 through 10  
have lights and can have lines assigned.  
■ Make as many copies of each page of Form C as you need. Where line and  
other button assignments are identical for two or more phones of the same  
type, you can use one copy of the form and indicate the extension numbers  
sharing the programming in the space provided at the bottom of the form.  
MLS-6® Telephone  
1
2
3
4
■ Indicate the order in which a line is selected when the user lifts the handset  
or presses S to place a call without first pressing a line or button (Auto-  
matic Line Selection) if the order is to be different than the default (outside  
lines in ascending numerical order followed by intercom).  
■ Use either the button template (to record the exact location of buttons and  
the programming assigned to them) or the Check Desired Features checklist  
(to identify features to be programmed), or both. By default, lines are  
assigned to buttons in the following order:  
PARTNER-34D Telephone  
19  
13  
7
1
14  
8
2
15  
9
3
16  
10  
4
17  
11  
5
18  
12  
6
PARTNER-18D and PARTNER-18 Telephones  
13  
9
5
14  
10  
6
15  
11  
7
16  
12  
8
1
2
3
4
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
10  
Intercom Autodialer  
The buttons on the Intercom Autodialer are automatically programmed as  
Intercom Auto Dial buttons for all system extensions in the following order:  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
NOTE: Extensions 42–49 are available only if you are using Release 2.0 or  
later of PARTNER ACS.  
You can program the buttons to ring, voice signal, or manually signal; and you  
can change the order. Only one button (on both the phone and  
Intercom Autodialer) can be programmed for each extension.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
page 11.) The 34-button telephone has 15 lines assigned, and the Intercom  
Autodialer is programmed with Intercom Auto Dial and Manual Signaling buttons  
for 31 extensions; the order of extensions has been changed to begin with  
extension 11 on the top left button. The user’s 18-button telephone has 5  
individual lines assigned; the other 11 buttons are used for Intercom Auto Dialing  
and dial-code features.  
Example Templates  
These examples show a PARTNER-34D telephone, PARTNER-CA48 Intercom  
Autodialer programmed for a receptionist, and a PARTNER-18 telephone  
programmed for a system in Hybrid mode for a user at a pooled extension.  
Buttons that are not used for lines or pools have dial-code features. (The  
abbreviations are explained in “Button Feature Summary” beginning on  
PARTNER-34D Telephone  
PARTNER-CA48 Intercom Autodialer  
Ext-11  
Ext-22  
ExtVS-33  
MS-44  
Sally  
Ext-12  
Joe  
Ext-23  
Sean  
MSVS-34  
Jack  
Ext-45  
June  
MSVS-46  
Lou  
Ext-13  
Ken  
Ext-24  
Steve  
Ext-35  
Kay  
ExtVS-47  
Ted  
Ext-14  
Rich  
Ext-36  
Dawn  
Ext-25  
Raj  
MSVS-49  
Linda  
Ext-15  
Hank  
Ext-26  
Mark  
Ext-37  
Hans  
Ext-16  
Jim  
ExtVS-27  
Jon  
Nan  
Ext-38  
Kim  
Ext-17  
Paul  
Ext-28  
Eve  
Ext-39  
Intercom  
Intercom  
Ext.  
Don  
Mike  
Bill  
Ext-18  
Ext-29  
Ext-40  
PARTNER-18 Telephone  
Raoul  
Kyle  
Zack  
ExtVS-19  
Ext-30  
MSVS-41  
VMMsgs-777  
Messages  
Laura  
Ext-20  
Kathy  
Ext-31  
Deb  
ExtVS-42  
DND  
ExtVS-23  
Priv  
Ext-22  
CC1  
Ext-10  
Lila  
Ext-21  
John  
ExtVS-32  
Jean  
ExtVS-43  
Lou  
Joe  
Pat  
Music  
12  
SNR  
LNR  
13  
Anvi  
Fran  
Jeff  
14  
VIOB  
10  
Intercom  
11  
Intercom  
Ext.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Wake Up Service Button  
Wake  
{#115}  
Button Feature Summary  
This section lists button features in order by feature type and feature name.  
For each feature, the first line shows the following information:  
Allows the user at extension 10 to schedule an intercom call to a target extension at a  
designated time. If Music on Hold {#602} is active, music is played when the phone is  
answered; otherwise, nothing is heard.  
■ The name of the feature.  
Auto Dialing Features  
■ Whether a button with lights is required ( ) or recommended ( ).  
■ An abbreviation that can be entered on the Form C templates.  
Auto Dial numbers can include the digits 0–9, *, #, and special functions  
that you store by pressing h (Pause), ! (Stop), S (Recall), and  
& (Touch-Tone Enable). To store an intercom number, you must press the  
left i button before entering the extension number. Only one Auto Dial  
number for an extension can be stored on the buttons available at an extension  
for both the phone and Intercom Autodialer.  
■ The entries needed to program the feature on a button. Some features can  
include a two-digit extension number (shown as xx) or a single-digit group  
number (shown as g).  
Auto Dialing (Outside Phone Number)  
xxx-xxxx  
Extension 10 Features  
Places a call to an outside telephone number. Outside telephone numbers can be  
up to 28 digits. If a dial-out code is required to dial outside numbers (for example, on  
PBX or Centrex lines), include it in the stored number followed by pauses, if  
necessary.  
These features can be assigned only to the phone at extension 10. Auto dialing  
and dial-code features can also be used at extension 10; of particular interest  
are the Intercom Auto Dialing and Manual Signaling features, which use button  
lights to show extension calling activity.  
Auto Dialing (PBX/Centrex Feature Code)  
xxx (NAME)  
Automatic System Answer Button  
ASA  
{#111}  
Dials a PBX/Centrex feature code. To program the button so the user can access  
the feature while on a call, specify “R” on Form C before the feature code, and  
include the Recall signal on the Auto Dial button.  
(ACS R2.0 or later only) Turns Automatic System Answer on and off. When the  
feature is on, a call that is not answered by the receptionist is answered by the  
system; the system plays a brief message, then places the call on hold, continues to  
ring all extensions that have the line, or disconnects the call. To use Automatic  
System Answer, extension 10 must be programmed with an ASA button.  
Fax Management  
Fax-xx  
ixx  
Transfers calls to the fax machine at the designated extension with one touch. If on  
a button with lights, the lights show when the fax is busy or when it is having trouble  
and not answering—for example, when it is out of paper.  
Direct Extension Dial Button  
DXD  
{#113}  
(ACS R2.0 or later only) Turns Direct Extension Dial on and off. When the feature is  
on, a call that is not answered by the receptionist is answered by the system; the  
system plays a brief message, then lets the caller dial an extension number or wait  
for the receptionist. To use Direct Extension Dialing, extension 10 must be  
programmed with a DXD button.  
Intercom Auto Dialing—Ring  
Ext-xx  
ixx  
Places a ringing intercom call to an extension, or transfers a call. If on a button with  
lights, the lights show calling activity at the destination extension.  
Intercom Auto Dialing—Voice Signal  
ExtVS-xx  
i*xx  
Places a voice-signaled intercom call to the extension’s phone speaker, or transfers  
a call with a voice-signaled announcement. If on a button with lights, the lights show  
calling activity at the destination extension.  
Night Service Button  
NightSvc  
{#503}  
Turns Night Service on and off. Phones in the Night Service Group ring immediately  
when the feature is active, regardless of normal ringing. To use Night Service,  
extension 10 must be programmed with a Night Service button. Night Service Group  
extensions should be identified on Form B2.  
Outgoing Call Restriction Button  
OCR  
{#114}  
Allows the user at extension 10 to change the outgoing call restriction for a particular  
extension. An Auto Dial button with lights must be programmed for each extension to  
be changed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Manual Signaling—Ring  
MS-xx  
F13xx  
Caller ID Name Display  
ID-Name  
F16  
Beeps the designated extension. If the user presses i first, pressing the button  
places a ringing intercom call to the extension, or transfers a call. If on a button with  
lights, the lights show calling activity at the destination extension.  
When a user at a display phone is on a call on a line that has Caller ID information  
available, this feature lets the user switch between the caller’s telephone number  
(the default display) and the caller’s name (if available). When the feature is active—  
indicating that the caller’s name should be displayed—the button light is on.  
Manual Signaling—Voice Signal  
MSVS-xx  
F13* xx  
Beeps the designated extension. If the user presses i first, pressing the button  
places a voice-signaled intercom call to the extension, or transfers a call with a  
voice-signaled announcement. If on a button with lights, the lights show calling  
activity at the destination extension.  
Conference Drop  
Drop  
F06  
Drops the last outside party added to a conference call.  
Contact Closure 1 CC1  
f41  
Allows user to activate Contact Closure 1. User must belong to Contact Closure  
Group. See Form B1.  
Dial-Code Features  
Account Code Entry  
Contact Closure 2  
CC2  
f42  
ACE  
F12  
Allows user to activate Contact Closure 2. User must belong to Contact Closure  
Group. See Form B1.  
Allows the user to enter an account code for a call by pressing the button, entering  
up to 16 digits for the account code, then pressing the button again. If on a button  
with lights, the lights show when the feature is in use.  
Direct Line Pickup—Active Line  
DLPA  
i68  
Allows the user to access a ringing, active, or held call on a line that is not assigned  
to the extension. Direct Line Pickup is subject to Line Access Restrictions  
programmed for the extension.  
Background Music  
Music  
F19  
Turns background music on and off at the speaker of an idle system phone. If on a  
button with lights, the lights show when the feature is in use.  
Direct Line Pickup—Idle Line  
DLPI  
i8  
Call Coverage  
Cover-xx xx F20 xx xx  
Allows the user to access an idle (non-busy) line that is not assigned to the  
extension. Direct Line Pickup is subject to Line Access Restrictions programmed for  
the extension.  
(ACS R2.0 or later only) Directs all intercom, transferred, and outside calls on lines  
assigned ownership to the designated extension. You may program originating and  
covering extension numbers on the button. If on a button with lights, the lights show  
when the feature is in use.  
Do Not Disturb  
DND  
F01  
Prevents calls from ringing at the extension. When the feature is active, the button  
light is on. Intercom calls get a busy signal, and outside callers hear ringing. Use  
only if someone else answers the extension’s outside calls.  
Call Forwarding/Call Follow-me  
CF-xx xx  
F11 xx xx  
Forwards all calls to the designated extension. Unless Do Not Disturb is on, phone  
beeps once each time a call is forwarded. You may program originating and  
destination extension numbers on the button. If on a button with lights, the lights  
show when the feature is in use.  
If VMS Cover and Do Not Disturb are both active, intercom, transferred, and outside  
calls on owned lines go directly to the extension’s voice mailbox. If Call Coverage  
and Do Not Disturb are both active, intercom, transferred, and outside calls on lines  
assigned ownership go directly to the covering extension.  
Call Park  
Park  
ixx  
Parks a call at a specific extension so it can be picked up from any other extension.  
Exclusive Hold  
ExHold  
F02  
Call Pickup  
Pickup-xx i6 xx  
Places a call on hold and prevents other extensions with the line from picking it up.  
Picks up a ringing or parked call at the designated extension.  
Group Calling—Page  
GCallP-g  
i*7 g  
Caller ID Inspect ID-Inspect  
F17  
Places a voice-signaled intercom call to all extensions in the designated Calling  
Group (no transfer capability). The caller is connected to the first extension that  
answers. g = 1–4  
When a user at a display phone is already on a call, this feature shows Caller ID  
information for another line (if Caller ID information is available on that line), without  
disconnecting the current call or putting it on hold. When the feature is active, the  
button light is on.  
Group Calling—Ring  
GCall-g  
i7 g  
Places a ringing intercom call to all extensions in the designated Calling Group. The  
caller is connected to the first extension that answers. Also can be used to transfer  
a call to an extension in the group. g = 1–4  
Caller ID Call Logging and Dialing  
ID-Logs  
F23  
(ACS R2.0 or later only) Users at a display phone, can access a Caller ID log to  
ascertain caller’s phone numbers automatically. When a user has logged calls, the  
word CALLS displays.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Group Hunting—Ring  
Hunt-g  
i77 g  
Save Number Redial  
SNR  
f04  
Rings the first available extension in the designated Hunt Group, or transfers a call  
to an extension in the group. If unanswered after 3 rings, the call moves to the next  
available extension, and so on, until the call is answered or until the caller hangs up.  
g = 1–6  
This feature can be programmed onto more than one button. Using this feature  
while on an outside call saves the number dialed into temporary memory. The  
number stays in memory until a different one is saved; this feature can be used  
again to redial the number at any time. (Unlike Last Number Redial, the user must  
use this feature to save the number as well as to redial it; Save Number Redial lets  
the user make other outside calls before redialing the saved number.) Account  
codes cannot be saved and redialed using this feature.  
Group Hunting—Voice Signal  
HuntVS-g  
i*77 g  
Voice signals the first available extension in the designated Hunt Group, or transfers  
a call to the extension with a voice-signaled announcement. The caller is connected  
only if that extension answers. g = 1–6  
Simultaneous Paging  
SPage  
i*70  
Accesses the loudspeaker paging system and all idle system phones with speakers  
assigned to Calling Group 1.  
Group Pickup  
P/U Grp-g  
i66 g  
Picks up an intercom, transferred, or outside call ringing at any extension in the  
designated Pickup Group. g = 1–4  
Station Lock  
Lock  
f21  
Lets the user lock the extension by entering a code of four digits (0-9) on the  
telephone dialpad.  
Last Number Redial  
LNR  
f05  
Automatically redials the last outside number dialed up to a maximum of 28 digits.  
This feature can be used only to redial the last outside number dialed.  
Touch-Tone Enable  
TT-EN  
f08  
Lets user with rotary lines access phone services that require touch-tone digits. For  
example, after calling a bank-by-phone service and being prompted to enter touch-  
tone digits, using this feature changes the digits dialed to touch tones for the rest of  
the call.  
Loudspeaker Paging  
Loudspk  
i70  
Connects the user to the loudspeaker paging system, if one is connected to the  
system.  
Message Light Off  
MsgOff-xx f10 xx  
Turns off the message light on the phone at the designated extension. You can also  
program an extension number on the button.  
VMS Cover  
VMSCover f15  
Turns voice mail coverage for the extension on and off if PARTNER MAIL,  
PARTNER MAIL VS, or PARTNER Voice Messaging is installed. When the feature  
is active, the button light is on. This feature overrides Automatic VMS Cover.  
Message Light On  
MsgOn-xx f09 xx  
Turns on the message light on the phone at the designated extension. You can also  
program an extension number on the button.  
Voice Interrupt on Busy Talk-Back  
VIOB  
f18  
Lets user respond to voice interrupt on busy call while still active on the existing call.  
Privacy  
Priv  
f07  
Voice Mail Messages VMMsgs-777 i777  
Prevents other people with the same line from joining calls being conducted at this  
extension. When the feature is active, the button light is on. This feature overrides  
Automatic Extension Privacy {#304}.  
Places an intercom call to the PARTNER MAIL, PARTNER MAIL VS, or PARTNER  
Voice Messaging (if available), so the user can check messages, send messages,  
or administer greetings.  
Recall  
Recall  
f03  
Voice Mailbox Transfer  
VMBox  
f14  
“Recalls” a dial tone to access a PBX/Centrex feature while on a call on a PBX/  
Centrex line (pressing Recall disconnects an intercom call).  
Transfers a caller directly to a specific extension’s voice mailbox, so that the caller  
can leave a message without having to first ring the extension.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Form D Supplemental Instructions:  
Number Lists  
Use this form to specify lists of Disallowed, Allowed, and Emergency telephone  
numbers. Also use this form to identify the phone numbers dialed automatically  
by External Hotlines.  
Disallowed Phone Number Lists {#404}  
With Disallowed lists, you can prevent users from dialing specific telephone  
numbers or categories (for example, calls to 976 exchanges for pre-recorded  
messages such as horoscopes, and calls to 900 area code “chat lines”).  
NOTE: To restrict long-distance calling, Toll Call Prefix {#402} (indicating  
whether you must dial a 0 or 1 to place long distance calls) must be set cor-  
rectly (see Form A, Item 9).  
Examples of Disallowed List Entries  
Preventing Calls to 976 Exchange Numbers  
Entries needed . . .  
if 0 or 1 toll prefix  
is required  
976  
if 0 or 1 toll prefix  
is not required  
976  
Creating Disallowed and Allowed Lists  
You can create up to 8 lists each of Disallowed and Allowed telephone num-  
bers. Each list can have up to 10 numbers.  
0976  
!0!976  
1. Under the List number, write a name for the list (for example, “Suppliers”).  
1976  
!1!976  
1!!!976  
0!!!976  
2. In the “Telephone Number” column, write the entries for the list. You can  
specify complete telephone numbers or categories of numbers.  
Preventing Calls to 900 Area Code  
Entries needed . . .  
■ To specify a complete number, write it exactly as it would be dialed,  
if 0 or 1 toll prefix  
is required  
if 0 or 1 toll prefix  
is not required  
including (if needed) a dial-out code, toll call prefix, and area code.  
■ To specify a category, provide one or more entries to describe an entire  
class of calls (such as an area code or local exchange). Preventing calls  
to a category may require more than one entry, to allow for different ways  
of dialing a number (see “Examples of Disallowed List Entries”).  
0900  
1900  
900  
Preventing International (011) Calls  
After a list has been created, it can be assigned to an extension (see Form B2).  
Entry needed . . .  
011  
Preventing Use of a Specific Local Telephone Company Feature  
Consisting of a and Two or Three Digits.  
*
Entries needed for star codes; for  
example Caller ID Blocking, 67. . .  
67  
1167  
*
*
Allowed Phone Number Lists {#407}  
Allowed telephone numbers are exceptions to restrictions. For example, you might  
put 976 numbers on a Disallowed list, but allow dialing of 976-1212 for weather  
reports. Or you might restrict an extension to local dialing only, but assign an  
Allowed list to permit the user to call specific customers or suppliers.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
16  
External Hotline {#311}  
Emergency Phone Number List {#406}  
For each extension that has been designated as an External Hotline on Form B1,  
write the telephone number that is dialed automatically when the handset is lifted.  
You can create a list of emergency numbers that can be dialed at any time by  
any extension that has access to an outside line. The list can have up to 10  
entries. Emergency numbers override all other dialing restrictions, including  
Night Service with a System Password.  
Forced Account Code List {#409}  
If an extension has been designated for Forced Account Code Entry {#307} on  
Form B2, the user must dial an account code before an outside telephone  
number can be dialed. Account codes, each up to 16 digits in length, can be  
used to associate telephone calls with a particular department or client. Account  
codes print on SMDR call reports and on reports generated by call accounting  
packages.  
NOTE: Various factors influence the effectiveness of dialing restrictions. Avoid  
putting 800 numbers in your Emergency Phone Number List. If you need to  
allow restricted users to access 800 numbers, put those numbers in an Al-  
lowed Phone Number List instead.  
Important Notices  
■ Consult your local phone directory to determine the numbers for police, fire,  
If Forced Account Code Verification is desired, entries must be made in the  
Forced Account Code List {#409}. When the system verifies an account code, it  
compares only the first six digits of the user-entered account code to the entries  
in the Forced Account Code List. For a match to be successful, the user must  
dial at least the account code’s associated list entry, even though the user can  
dial up to 16 digits for an account code. Wildcard entries are allowed on this list.  
and ambulance service, because “911” is not available everywhere.  
■ When programming emergency numbers and/or making test calls to  
emergency numbers:  
1. Stay on the line and briefly explain to the dispatcher the reason for the  
call before hanging up.  
2. Perform such activities during off-peak hours, such as in the early  
morning or late evening.  
Example Emergency List  
911  
611 (local phone company service)  
555-2345 (Boss’s home)  
555-4567 (auto club)  
555-1357 (company doctor)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Form E Supplemental Instructions:  
System Speed Dial Numbers  
Telephone Number  
With System Speed Dialing, a user can dial a stored number by pressing four  
buttons: the f button (# on a standard phone) followed by a 3-digit code.  
Storing a telephone number as a Speed Dial number lets users dial more  
quickly. Other kinds of numbers—such as account codes and other dialing  
sequences—also can be stored as Speed Dial numbers.  
Write the number exactly as it should be dialed. Numbers can be up to 28  
digits, including the digits 0–9, *, #, and the special dialing functions  
discussed next. To store a telephone number, include the dial-out code,  
toll-call prefix, and area code (if needed), along with the number.  
The system allows up to 100 System Speed Dial numbers that everyone on the  
system can use, as well as up to 20 Personal Speed Dial numbers for each  
extension (for the personal use of the extension user). Users should record  
their Personal Speed Dial numbers on their Quick Reference Cards.  
Special Dialing Functions  
Function  
Button to Press  
Display Description  
Pause  
h
P
Pauses for 1.5 seconds  
before dialing the rest of the  
stored number  
Please have the System Speed Dial Numbers form filled out when the  
technician arrives to install the system. After installation, photocopy this form  
and distribute a copy to everyone using the system. Users should keep this  
form near their phones for reference when placing calls.  
Recall  
Stop  
S
R
Sends a timed switchhook  
flash (useful for your  
telephone company’s  
custom calling features)  
General Guidelines  
Each System Speed Dial number is assigned a 3-digit code from 600-699.  
For example, suppose employees frequently call Acme Supplies and Acme’s  
telephone number is stored for code 620. To call Acme, a user simply dials  
f 6 2 0. If Acme moves, or the phone number changes, program the  
new telephone number and users still dial f 6 2 0 to reach Acme.  
!
S
T
Interrupts the dialing  
sequence until the code is  
dialed again  
Touch-Tone Enable  
&
Sends touch tones on a  
rotary line  
Record the following information for each System Speed Dial number:  
Name/Company  
Write the name of the person or company to which the number belongs. For  
other types of numbers, such as account codes, enter a description of the  
number.  
Column (Marked System Speed Dial Numbers)  
If users should be able to call a particular System Speed Dial number,  
regardless of any dialing restrictions placed on their extensions, “mark” the  
number so it can be dialed at all times. Mark the number by placing a check  
mark in this column, and by pressing * before the number when storing it.  
*
For marked numbers, the stored number does not appear on a display  
phone when a user dials the Speed Dial code. Account codes cannot be  
marked.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
1 of 3  
Form A: System Configuration  
Required for PARTNER Advanced Communications System.  
For additional instructions, see page 2.  
6. Administer system for Hybrid Mode (ACS Release 2.0 and  
later only):  
1. Customer Billing Name  
2. Installation Address  
3. Contact Name  
No ■  
Yes ■ If yes, call local telephone company—  
MF Mode and FCC # AS5 USA-21312-MF-E  
Phone  
7. Features Customer is most interested in (most important first):  
(XXX) XXX – XXX  
Phone  
4. Person to be Trained  
Phone  
Alternate Trainee’s Name  
(XXX) XXX – XXX  
(XXX) XXX – XXX  
Phone  
5. Sold by  
■
■
Lucent Technologies Sales Force  
Dealer:  
Salesperson’s Name  
(XXX) XXX – XXX  
8 . System Lines  
Line Coverage—You can select one per line  
Write  
R if  
Hybrid Mode  
Only:  
7
1
2
3
4
5
6
*
*
*
AA  
DXD  
VMS- ASA  
AA  
Hunt  
VMS-  
Mail  
{#206}  
or  
Write  
Line Write the Telephone  
Jack Numbers in order  
No. customer desires  
(list personal and  
Write User’s Name for  
Personal or Owned Line  
Check Identify other Local  
if Telephone Company  
Rotary  
(Dial  
Group  
Ext. No.  
for Call  
Cover  
Write auxiliary  
*
or Identify Equipment for Caller Subscription Services  
{#607} {#205} {#206} {#204} (write no.)  
Pulse)  
Line  
{#201}  
pool 881, 882,  
883 or No Pool  
{#207}  
Dedicated Line  
ID  
(e.g., Repeat Call)  
{#206}  
Only one of these  
dedicated lines last)  
Service  
{#208}  
{#208}  
types per system  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
1. Check if desired. Also see Form B1, AA Extension {#607} column.  
5. Write group number (1–6) covering this line. Also see Form B2, Hunt Group Extensions {#505} 1–6.  
6. Check desired line for #206 or enter line owner’s extension number for #208. Also see Form B1, PARTNER  
MAIL, PARTNER MAIL VS, or PARTNER Voice Messaging PC CARD column.  
7. Write extension number of line owner eligible for Call Coverage. Also write line owner’s name in next  
column.  
2. Check if desired. Also see Form A, Item 10—DXD, and Form C, Direct Extension Dial Button {#113}.  
3. Check if desired. Also see Form A, Item 10—VMS-AA, and Form B1, PARTNER MAIL, PARTNER MAIL VS,  
or PARTNER Voice Messaging column.  
4. Check if desired. Also see Form A, Item 10—ASA, and Form C, Automatic System Answer Button {#111}.  
*
Available with PARTNER ACS R2.0 or later only.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
2 of 3  
Form A: System Configuration  
Required for PARTNER Advanced Communications System.  
For additional instructions, see page 3.  
9. System Settings. Write response on line for each item.  
•
•
Receptionist answers calls during business hours? Write “Yes” or “No” ______.  
Number of Lines {#104}—By default, 3 lines per PARTNER ACS processor module or  
308EC module, 2 lines per 206 module, and 4 lines per 400 module are assigned to each  
extension (or to pool 880 in Hybrid Mode). Write number if different from default ______.  
•
Transfer Return Rings {#105}—By default, a transferred call rings 4 times before going to  
the transfer return extension. Write number (0-9, 0 = no return) if different from  
default ______.  
VMS-AA: If VMS-AA is checked, specify the following:  
VMS Hunt Delay {#506}—By default, VMS answers calls after 2 rings. Write “Del” if  
calls ring 4 times before VMS answers _____.  
•
•
Outside Conference Denial {#109}—By default, a conference call can include 2 outside  
parties. Write “No” if 2 outside parties are not allowed ______.  
VMS Hunt Schedule {#507}—By default, VMS is on all the time. Check if Day only or  
Night only is desired:  
Call Coverage Rings {#116} (ACS Release 2.0 and later only)—By default, a covered call  
rings 2 times before going to the covering extension. Write number (1-9) if different from  
■
Day only  
default ______.  
■
Night only  
•
•
•
•
VMS Cover Rings {#117}—By default, a call rings 3 times before going to the user’s  
mailbox. Write number (1-9) if different from default ______.  
ASA: (ACS Release 2.0 and later only) If ASA is checked, specify the following:  
Automatic System Answer Delay {#110}—By default, a call rings 2 times before it is  
answered by the system. Write number (0-9) if different from default _____.  
Ring on Transfer {#119}—By default, the caller hears ringing when the call is transferred.  
Write “NA” if music on hold or silence is desired ______.  
Automatic System Answer Mode {#121}—By default, ASA calls are put on hold after the  
greeting plays. Check if calls should continue to ring or be disconnected:  
Toll Call Prefix {#402}—By default, 0 or 1 must be dialed before the area code for a  
long distance call. Write “No” if 0 or 1 is not required ______.  
■
■
Ring  
Disconnect  
System Password {#403}—By default, no password is programmed to override dialing  
restrictions and to turn Night Service on and off. Write 4 digits if password is  
desired __ __ __ __.  
ASA Record/Playback (I 891)—message of up to 10 seconds that caller hears  
when the call is answered by the Automatic System Answer feature. Write  
message below and record from extension 10 or 11:  
•
•
Star Code Dial {#410}—By default, the system inserts a 0-second delay after a  
valid Central Office star code when it autodials. Write number (1–5) of seconds if a longer  
delay is desired or “NO” if this feature should not be active ______.  
Music on Hold {#602}—By default, the Music on Hold jack on the processor module is  
active. Write “No” if the jack is deactivated ______.  
10. Line Coverage. Complete items based on Line Coverage selection on Form A, Item 8.  
DXD: (ACS Release 2.0 and later only) If DXD is checked, specify the following:  
Direct Extension Dial Delay {#112}—By default, a call rings 2 times before it is  
answered by the system. Write number (0-9) if different from default _____.  
Direct Extension Dial Record/Playback (I 892)—message of up to 20 seconds that  
caller hears when call is answered with the Direct Extension Dial feature. Write  
message below and record from extension 10 or 11:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
3 of 3  
Form A: System Configuration  
Required for PARTNER Advanced Communications System.  
For additional instructions, see page 4.  
11. Auxiliary Equipment (System). Check if applicable:  
■ Battery Backup  
■ Caller ID Devices  
■ Loudspeaker Paging: Number of zones ______________  
■ Magic on Hold (Music on Hold {#602} must be active.)  
■ Uninterruptible Power Supply  
■ SMDR If checked, specify the following if appropriate:  
• SMDR Record Type {#608}—By default, all calls are included on call reports. Write  
“Out” if only outgoing calls are reported _________.  
• SMDR Output Format {#610}—By default, up to 15 digits are printed for dialed  
numbers in the Number field of the call report. Write “24” if a maximum of 24 digits  
is desired _________.  
• SMDR Talk Time {#611}—By default, a Talk field is not included on the call report.  
Write “Active” if the Talk field is desired_________.  
■ PARTNER Contact Closure Adjunct. If checked, write in the number (1–4) below to  
specify Operation Type for each Contact Closure as appropriate:  
OperationType  
{#613}  
Contact  
Closure 1  
Contact  
Closure 1  
1 = 1 second on  
2 = 3 seconds on (✓)  
3 = 5 seconds on  
4 = Toggle  
■ Backup/Restore PC Card. If checked, write “Active” if Automatic System  
Programming Backup {#123} is desired _________.  
ASA/DXD PC Card  
PARTNER Voice Messaging PC Card  
12. Notes: Write any additional information that you want to communicate to the installer.  
13. Installation Date  
14. Order Nos.  
Telephone No.  
15. Sales Support Representative’s Name  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
1 of 4  
Form B1: System Extensions  
Required for PARTNER Advanced Communications System.  
For additional instructions, see page 5.  
Identify Telephone  
Attached to this Extension  
Identify Auxiliary Equipment  
Attached to this Extension  
Write  
Transfer  
Return  
Ext. No.  
{#306}  
Ext.  
Jack  
No.  
Write in  
Other  
Equipment  
Write Name/Description  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
IMPORTANT: A system display phone is required for programming at extension 10 or 11. Extension 10 typically is the receptionist’s extension.  
Extension 11 is recommended as a second programming extension (typically the System Manager’s extension).  
1. If checked, see Form B1, Page 3 of 4  
7. To prevent other extensions from interrupting calls, assign Automatic Extension Privacy {#304} on Form B2.  
8. Check corresponding alert extensions in next column. To prevent outside calls, remove all outside lines–see  
Lines/Pools Not Assigned on Form B2.  
2. If there is a mix of PARTNER-model and MLS-model phones, write “P” for PARTNER and “M” for MLS.  
3. Write “T” for touch-tone or “R” for rotary. If Call Waiting is desired, check next column.  
4. Must be standard phone. If immediate dialing is required, use a dedicated line. Do not assign restrictions that prevent dialing the  
outside number, Forced Account Code Entry {#307}, or groups. Also see Form D, External Hotline {#311}.  
5. Standard phone is recommended. Write extension number of corresponding alert extension or “70” for loudspeaker paging  
system in next column.  
9. Also write Transfer Return Ext. No. {#306} on this form.  
10. Virtual extensions 86 and 87 are automatically assigned to the two voice ports on PARTNER Voice Messaging.  
Virtual extensions 86 and 87 are also assigned to Hunt Group 7 and any previous assignments for Hunt Group 7  
are automatically erased.  
6. Also write Transfer Return Ext. No. {#306} on this form (usually extension 10). Also see Form B2, Identify Group Assign-  
ments, VMS Only.  
*
Do not connect to extension 10, 11, or the first two extensions of any 206 or 308EC module.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
2 of 4  
Form B1: System Extensions  
Required for PARTNER Advanced Communications System.  
For additional instructions, see page 5.  
Identify Telephone  
Attached to this Extension  
Identify Auxiliary Equipment  
Attached to this Extension  
Write  
Transfer  
Return  
Ext. No.  
{#306}  
Ext.  
Jack  
No.  
Write in  
Other  
Equipment  
Write Name/Description  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42 10  
43 10  
44 10  
45 10  
46 10  
47 10  
48 10  
49 10  
86 11  
87 11  
✓
✓
1. If checked, see Form B1, Page 4 of 4  
7. To prevent other extensions from interrupting calls, assign Automatic Extension Privacy {#304} on Form B2.  
8. Check corresponding alert extensions in next column. To prevent outside calls, remove all outside lines–see  
Lines/Pools Not Assigned on Form B2.  
9. Also write Transfer Return Ext. No. {#306} on this form.  
10. Available only for PARTNER ACS R2.0 or later.  
2. If there is a mix of PARTNER-model and MLS-model phones, write “P” for PARTNER and “M” for MLS.  
3. Write “T” for touch-tone or “R” for rotary. If Call Waiting is desired, check next column.  
4. Must be standard phone. If immediate dialing is required, use a dedicated line. Do not assign restrictions that  
prevent dialing the outside number, Forced Account Code Entry {#307}, or groups. Also see Form D, External  
Hotline {#311}.  
11. PARTNER Voice Messaging PC Card available only with Release 1.1 or later. Virtual extension available only  
5. Standard phone is recommended. Write extension number of corresponding alert extension or “70” for loud-  
speaker paging system in next column.  
6. Also write Transfer Return Ext. No. {#306} on this form (usually extension 10). Also see Form B2, Identify Group  
with Release 1.1 or later and used only when a PARTNER Voice Messaging PC Card is installed.  
Do not connect to extension 10, 11, or the first two extensions of any 206 or 308EC module.  
*
Assignments, VMS Only.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
3 of 4  
Form B1: System Extensions  
May be used if Ext. Name Display is checked on Form B1,  
page 1 of 4 or page 2 of 4.  
Character Codes  
Letters:  
Ext.  
Jack  
No.  
A = 21  
B = 22  
C = 23  
D = 31  
E = 32  
F = 33  
G = 41  
H = 42  
N = 62  
O = 63  
P = 71  
Q = 72  
R = 73  
S = 74  
T = 81  
U = 82  
V = 83  
W = 91  
X = 92  
Y = 93  
Z = 94  
Write 2-Digit Code for Each Character To Be Displayed — See Table at Right  
10  
11  
12  
13  
14  
15  
I
= 43  
16  
17  
18  
19  
20  
21  
J = 51  
K = 52  
L = 53  
M = 61  
Numbers:  
blank = 11  
0 = 00  
1 = 10  
2 = 20  
3 = 30  
4 = 40  
22  
23  
24  
25  
26  
27  
5 = 50  
6 = 60  
7 = 70  
8 = 80  
9 = 90  
28  
29  
30  
31  
32  
33  
Note: Only 12 characters display on MLS-model phones.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
4 of 4  
Form B1: System Extensions  
May be used if Ext. Name Display is checked on Form B1,  
page 2 of 4.  
Character Codes  
Letters:  
Ext.  
Jack  
No.  
A = 21  
B = 22  
C = 23  
D = 31  
E = 32  
F = 33  
G = 41  
H = 42  
N = 62  
O = 63  
P = 71  
Q = 72  
R = 73  
S = 74  
T = 81  
U = 82  
V = 83  
W = 91  
X = 92  
Y = 93  
Z = 94  
Write 2-Digit Code for Each Character To Be Displayed — See Table at Right  
34  
35  
36  
37  
38  
39  
I
= 43  
40  
41  
42  
43  
44  
45  
J = 51  
K = 52  
L = 53  
M = 61  
Numbers:  
blank = 11  
0 = 00  
1 = 10  
2 = 20  
3 = 30  
4 = 40  
46  
47  
48  
49  
5 = 50  
6 = 60  
7 = 70  
8 = 80  
9 = 90  
Notes: Only 12 characters display on MLS-model phones.  
Extensions 42–49 are available only if you are using PARTNER ACS Release 2.0 or later.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
1 of 2  
Form B2: Customized Extension Settings  
Required if you want to change extension settings from defaults. For additional instructions, see pages 6 and 7.  
Identify Extension Settings  
if Different than Default  
Identify  
Group Assignments  
Identify Line Ringing {CTP} Option  
If Different than Default  
Identify Restrictions/Permissions  
If Different than Defaults  
Hybrid Mode  
Only:  
Write line numbers or pool access codes  
for Line Access Restriction {#302} or  
Pool Access Restriction {#315}*  
Write line numbers or pool access codes* in each  
column to show desired Line Ringing options  
No Restriction  
✔
No Ring  
pools  
Lines/Pools3  
Not Assigned  
1 – 4 1 – 4 1 – 4 1 – 4 1 – 6  
7
*
*
Immediate  
lines  
Incoming  
only  
Outgoing  
only  
NA✔  
Delayed  
No Access NR  
✔
✔
✔
E
✔
NA✔  
A✔  
NA✔  
A✔  
NA✔  
NA✔  
P✔  
NA✔  
NA✔  
NA✔  
NA✔  
K
ALL  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
1. Write S for Spanish or F for French.  
2. In Hybrid Mode only, write K for Key extension. Extension 10 always operates  
as a Key extension.  
3. In Key Mode, use Line Assignment {#301} to remove lines from or assign lines  
to extensions. In Hybrid Mode, use Pool Extension Assignment {#314} to  
remove pools from or assign pools to extensions.  
4. Write IN for Inside Only or LOC for Local Only to indicate restrictions for all  
outgoing calls on all lines.  
Assignments  
6. Write list number (1–8). Also see Form D, Allowed Phone Number Lists {#407}.  
7. Write group number (1–4).  
8. Write group number (1–4). If a loudspeaker is connected and Simultaneous Paging is desired,  
put appropriate extensions in Calling Group 1. Also see Form C, Simultaneous Paging.  
9. Write group number (1–6).  
10. Check off the same PARTNER MAIL or PARTNER MAIL VS extensions indicated on Form B1.  
For the PARTNER Voice Messaging PC Card, virtual extensions 86 and 87 are automatically  
assigned to Hunt Group 7.  
✔
A
E
NA  
NR  
P
=
=
=
=
=
=
Default  
Assigned or Active  
English  
Not Assigned or Not Active  
No Restriction  
Pooled  
{CTP} = Centralized Telephone Programming  
5. Write list number (1–8). Also see Form D, Disallowed Phone Number Lists {#404}.  
*
Pooling available only for ACS R2.0 or later.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
2 of 2  
Form B2: Customized Extension Settings  
Required if you want to change extension settings from defaults. For additional instructions, see pages  
6 and 7.  
Identify Extension Settings  
if Different than Default  
Identify  
Group Assignments  
Identify Line Ringing {CTP} Option  
If Different than Default  
Identify Restrictions/Permissions  
If Different than Defaults  
Hybrid Mode  
Only:  
Write line numbers or pool access codes  
for Line Access Restriction {#302} or  
Pool Access Restriction {#315}*  
Write line numbers or pool access codes* in each  
column to show desired Line Ringing options  
No Restriction  
✔
No Ring  
pools  
Lines/Pools3  
Not Assigned  
1 – 4 1 – 4 1 – 4 1 – 4 1 – 6  
7
*
Immediate  
lines  
Incoming  
only  
Outgoing  
only  
NA✔  
Delayed  
No Access NR  
✔
✔
✔
E
✔
NA✔  
A✔  
NA✔  
A✔  
NA✔  
NA✔  
P✔  
NA✔  
NA✔  
NA✔  
NA✔  
34  
35  
36  
37  
38  
39  
40  
41  
42*  
43*  
44*  
45*  
46*  
47*  
48*  
49*  
8611  
8711  
✓
✓
Assignments  
1. Write S for Spanish or F for French.  
2. In Hybrid Mode only, write K for Key extension.  
3. In Key Mode, use Line Assignment {#301} to remove lines from or assign lines  
to extensions. In Hybrid Mode, use Pool Extension Assignment {#314} to  
remove pools from or assign pools to extensions.  
5. Write list number (1–4). Also see Form D, Disallowed Phone Number Lists {#404}.  
6. Write list number (1–4). Also see Form D, Allowed Phone Number Lists {#407}.  
7. Write group number (1–4).  
8. Write group number (1–4). If a loudspeaker is connected and Simultaneous Paging is desired,  
put appropriate extensions in Calling Group 1. Also see Form C, Simultaneous Paging.  
9. Write group number (1–6).  
✔
A
E
NA  
NR  
P
=
=
=
=
=
=
Default  
Assigned or Active  
English  
Not Assigned or Not Active  
No Restriction  
4. Write IN for Inside Only or LOC for Local Only to indicate restrictions for all  
Pooled  
outgoing calls on all lines.  
10. Check off the same PARTNER MAIL, PARTNER MAIL VS, or PARTNER Voice Messaging PC  
Card extensions indicated on Form B1.  
{CTP} = Centralized Telephone Programming  
*
Available only for ACS R2.0 or later.  
11. Virtual extension available only for ACS R1.1 or later and used only when a PARTNER Voice  
Messaging PC Card is installed.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
1 of 8  
Form C1: PARTNER-34D Phone  
Make as many copies as you need. Use template and/or checklist. For additional instructions, see pages 8 through 13.  
Check Desired Features  
Also write in extension or group number  
Automatic System Answer Button {#111} 6  
ASA  
SAMPLE  
Template Instructions  
Direct Extension Dial Button {#113} 6  
Night Service Button {#503}  
Outgoing Call Restriction Button {#114} 1  
Wake Up Service Button {#115}  
Caller ID Call Log (F 23) 6  
Caller ID Inspect (F 17)  
DXD  
NightSvc  
OCR  
• If desired, write in line number, pool access code†, dial code feature, or auto dial number  
• If desired, write in Line Ringing (Imm, Del, or No) from Form B2  
04  
DEL  
IN  
• If desired, write in Line Access Restriction or Pool Access Restriction†  
(Out, In, or No) from Form B2  
Wake  
Calls  
† Available with ACS R2.0 or later only.  
ID-Inspect  
ID-Name  
DND  
Caller ID Name Display (F 16)  
Do Not Disturb (F 01)  
Privacy (F 07)  
Priv  
VMS Cover (F 15)  
VMSCover  
VIOB  
Voice Interrupt on Busy Talk-Back (F 18)  
Account Code Entry (F 12)2  
Background Music (F 19)2  
ACE  
1. Requires Auto  
Dial button for  
Music  
,6  
Call Coverage (F 20 XX XX)2,4  
Cover-XX XX  
each extension.  
2. Button with  
lights is  
Call Forwarding/Call Follow-Me (F 11 XX XX) 2,4 CF-XX XX  
Call Park (  
I
XX) 3  
Park  
Pickup-XX  
Drop  
recommended,  
but not required.  
Call Pickup (  
I
6 XX)  
3. Extension  
number can be  
programmed as  
Auto Dial  
Conference Drop (F 06)  
Contact Closure 1 (F 41) 2  
Contact Closure 2 (F 42) 2  
Direct Line Pickup-Active Line (  
CC1  
CC2  
button.  
4. You can  
program the  
origination  
I
68)  
DLPA  
DLPI  
ExHold  
Direct Line Pickup-Idle Line (  
Exclusive Hold (F 02)  
I
8)  
extension only  
or both the  
origination and  
destination  
extension.  
Fax Management (  
Group Calling-Ring/Page (  
Group Hunt-Ring/Signal ( 77 G or  
Group Pickup ( 66 G)  
Intercom Autodial ( XX or  
Last Number Redial (F 05)  
Loudspeaker Paging ( 70)  
I
XX) 2  
FAX-XX  
GCall-g  
Hunt-g  
I
7 G or  
I
I
*7 G)  
*77 G)  
I
5. You can  
program the  
extension  
number.  
6. Available with  
ACS R2.0 or  
later only.  
I
P/U Grp-g  
Ext-XX  
I
I
*XX) 2  
LNR  
I
Loudspk  
Manual Signaling (F 13 XX or F 13 *XX) 2  
MS-XX  
MsgOff-XX  
Intercom  
Intercom  
Message Light Off (F 10 XX) 5  
Message Light On (F 09 XX) 5  
F
= Feature button  
G = Group  
= Left Intercom  
button  
XX = Extension  
Ext.  
MsgOn-XX  
Recall (F 03)  
Save Number Redial (F 04)  
Recall  
SNR  
I
In Hybrid mode only, if pool 880 is assigned, these two buttons are associated with this pool. (ACS R2.0 or later only)  
Simultaneous Paging  
Station Lock (F 21) 2  
(I  
* 70)  
SPage  
Lock  
*
Specify Automatic Line Selection: ________________________________________________________________  
Identify extensions programmed as shown: ________________________________________________________  
Touch-Tone Enable (F 08)  
Voice Mail Messages Button (  
Voice Mailbox Transfer (F 14)  
TT-EN  
VMMsgs-777  
VMBox  
I
777)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
PAGE  
2 of 8  
Form C2: Intercom Autodialer  
Make as many copies as you need. Extension 10, Extension 11, or both can  
have an Intercom Autodialer. For additional instructions, see page 9.  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
Template Instructions  
• The numbers in the lower right corner for each button represent  
the default extension assignments. If you change them, write in the  
new assignments.  
SAMPLE  
MSVS–30  
• If desired, write in Intercom Ring (Ext-XX) or Voice Signal (ExtVS-XX), or  
Manual Signal Ring (MS-XX) or Voice Signal (MSVS-XX)  
• If desired, write in user name for this extension  
S. Jones  
Extensions programmed as shown (circle choices): 10 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
3 of 8  
Form C3: PARTNER-18 Phone  
Make as many copies as you need. Use template and/or checklist. For additional instructions, see pages 8 through 13.  
Check Desired Features  
Also write in extension or group number  
Automatic System Answer Button {#111} 6  
ASA  
Direct Extension Dial Button {#113} 6  
Night Service Button {#503}  
Outgoing Call Restriction Button {#114} 1  
Wake Up Service Button {#115}  
Caller ID Call Log (F 23) 6  
Caller ID Inspect (F 17)  
DXD  
NightSvc  
OCR  
SAMPLE  
Template Instructions  
• If desired, write in line number, pool access code†, dial code feature, or auto dial number  
• If desired, write in Line Ringing (Imm, Del, or No) from Form B2  
04  
DEL  
IN  
Wake  
• If desired, write in Line Access Restriction or Pool Access Restriction†  
(Out, In, or No) from Form B2  
Calls  
ID-Inspect  
ID-Name  
DND  
† Available with ACS R2.0 or later only.  
Caller ID Name Display (F 16)  
Do Not Disturb (F 01)  
Privacy (F 07)  
Priv  
VMS Cover (F 15)  
VMSCover  
VIOB  
PARTNER-18D only  
Voice Interrupt on Busy Talk-Back (F 18)  
Account Code Entry (F 12)2  
Background Music (F 19)2  
ACE  
1. Requires Auto  
Dial button for  
Music  
,6  
Call Coverage (F 20 XX XX)2,4  
Cover-XX XX  
each extension.  
2. Button with  
lights is  
Call Forwarding/Call Follow-Me (F 11 XX XX) 2,4 CF-XX XX  
Call Park (  
I
XX) 3  
Park  
Pickup-XX  
Drop  
recommended,  
but not required.  
Call Pickup (  
I
6 XX)  
3. Extension  
number can be  
programmed as  
Auto Dial  
Conference Drop (F 06)  
Contact Closure 1 (F 41) 2  
Contact Closure 2 (F 42) 2  
Direct Line Pickup-Active Line (  
CC1  
CC2  
button.  
I
68)  
DLPA  
DLPI  
ExHold  
4. You can  
program the  
origination  
Direct Line Pickup-Idle Line (  
Exclusive Hold (F 02)  
I
8)  
extension only  
or both the  
origination and  
destination  
extension.  
Fax Management (  
Group Calling-Ring/Page (  
Group Hunt-Ring/Signal ( 77 G or  
Group Pickup ( 66 G)  
Intercom Autodial ( XX or  
Last Number Redial (F 05)  
Loudspeaker Paging ( 70)  
I
XX) 2  
FAX-XX  
GCall-g  
Hunt-g  
P/U Grp-g  
Ext-XX  
I
7 G or  
I
I
*7 G)  
*77 G)  
I
5. You can  
program the  
extension  
number.  
6. Available with  
ACS R2.0 or  
later only.  
I
I
I
*XX) 2  
LNR  
Intercom  
Intercom  
I
Loudspk  
Manual Signaling (F 13 XX or F 13 *XX) 2  
Message Light Off (F 10 XX) 5  
MS-XX  
MsgOff-XX  
Ext.  
F
= Feature button  
G = Group  
= Left Intercom  
button  
XX = Extension  
Message Light On (F 09 XX) 5  
MsgOn-XX  
Recall (F 03)  
Save Number Redial (F 04)  
Recall  
SNR  
I
In Hybrid mode only, if pool 880 is assigned, these two buttons are associated with this pool.  
(ACS R2.0 or later only)  
*
Simultaneous Paging  
Station Lock (F 21) 2  
(I  
* 70)  
SPage  
Lock  
Specify Automatic Line Selection: ________________________________________________________________  
Identify extensions programmed as shown: __________________________________________________
Touch-Tone Enable (F 08)  
Voice Mail Messages Button (  
TT-EN  
VMMsgs-777  
VMBox  
I
777)  
Voice Mailbox Transfer (F 14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
4 of 8  
Form C4: PARTNER-6 Phone  
Make as many copies as you need. Use template and/or checklist.  
For additional instructions, see pages 8 through 13.  
Check Desired Features  
Also write in extension or group number  
SAMPLE  
Template Instructions  
Do Not Disturb (F 01)  
DND  
Priv  
• If desired, write in line number, pool access code†, dial code feature, or auto dial number  
• If desired, write in Line Ringing (Imm, Del, or No) from Form B2  
04  
DEL  
IN  
Privacy (F 07)  
VMS Cover (F 15)  
VMSCover  
VIOB  
• If desired, write in Line Access Restriction or Pool Access Restriction†  
(Out, In, or No) from Form B2  
Voice Interrupt on Busy Talk-Back (F 18)  
Account Code Entry (F 12)1  
ACE  
† Available with ACS R2.0 or later only.  
1. Button with  
lights is  
Background Music (F 19)1  
Call Coverage (F 20 XX XX)1,2,5  
✔
Music  
recommended,  
but not  
required.  
✔
Cover-XX XX  
Call Forwarding/Call Follow-Me (F 11 XX XX)1,2 CF-XX XX  
Call Park  
(I  
XX )3  
Park  
Pickup-XX  
Drop  
2. You can  
program the  
origination  
Call Pickup (  
I
6 XX)  
Conference Drop (F 06)  
extension only  
or both the  
origination and  
destination  
extension.  
Contact Closure 1 (F 41)1  
Contact Closure 2 (F 42)1  
Direct Line Pickup-Active Line (  
CC1  
CC2  
DLPA  
DLPI  
I
68)  
Direct Line Pickup-Idle Line (  
I
8)  
3. Extension  
number can be  
programmed as  
Auto Dial  
Exclusive Hold (F 02)  
ExHold  
Fax Management (  
Group Calling-Ring/Page (  
Group Hunt-Ring/Signal ( 77 G or  
Group Pickup ( 66 G)  
Intercom Autodial ( XX or  
Last Number Redial (F 05)  
Loudspeaker Paging ( 70)  
I
XX) 1  
FAX-XX  
GCall-g  
Intercom  
Intercom  
I
7 G or  
I
I
*7 G)  
*77 G)  
button.  
Ext.  
I
Hunt-g  
P/U Grp-g  
Ext-XX  
4. You can  
program the  
extension  
I
I
I
*XX) 1  
number.  
In Hybrid mode only, if pool 880 is assigned, these two buttons are associated with this pool.  
(ACS R2.0 or later only)  
*
LNR  
5. Available with  
ACS R2.0 or  
later only.  
I
Loudspk  
MS-XX  
MsgOff-XX  
MsgOn-XX  
Manual Signaling (F 13 XX or F 13 *XX) 1  
Message Light Off (F 10 XX) 4  
Message Light On (F 09 XX) 4  
Recall (F 03)  
Recall  
SNR  
Save Number Redial (F 04)  
Simultaneous Paging  
Station Lock(F 21) 1  
(I  
* 70)  
SPage  
Lock  
Touch-Tone Enable (F 08)  
Voice Mail Messages ( 777)  
Voice Mailbox Transfer (F 14)  
TT-EN  
VMMsgs-777  
I
VMBox  
F = Feature button G = Group I = Left Intercom button L = Line XX = Extension  
Specify Automatic Line Selection: ________________________________________________________________  
Identify extensions programmed as shown: __________________________________________________
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
5 of 8  
Form C5: MLS-34D Phone  
Make as many copies as you need. Use template and/or checklist. For additional instructions, see pages 8 through 13.  
Check Desired Features  
Also write in extension or group number  
Automatic System Answer Button {#111} 6  
ASA  
Direct Extension Dial Button {#113} 6  
Night Service Button {#503}  
Outgoing Call Restriction Button {#114} 1  
Wake Up Service Button {#115}  
Caller ID Call Log (F 23) 6  
Caller ID Inspect (F 17)  
DXD  
NightSvc  
OCR  
SAMPLE  
Template Instructions  
• If desired, write in line number, pool access code†, dial code feature, or auto dial number  
• If desired, write in Line Ringing (Imm, Del, or No) from Form B2  
04  
DEL  
IN  
Wake  
• If desired, write in Line Access Restriction or Pool Access Restriction†  
(Out, In, or No) from Form B2  
Calls  
ID-Inspect  
ID-Name  
DND  
† Available with ACS R2.0 or later only.  
Caller ID Name Display (F 16)  
Do Not Disturb (F 01)  
Privacy (F 07)  
Priv  
VMS Cover (F 15)  
VMSCover  
VIOB  
Voice Interrupt on Busy Talk-Back (F 18)  
Account Code Entry (F 12)2  
Background Music (F 19)2  
ACE  
1. Requires Auto  
Dial button for  
Music  
each extension.  
,6  
Call Coverage (F 20 XX XX)2,4  
Cover-XX XX  
2. Button with  
lights is  
Call Forwarding/Call Follow-Me (F 11 XX XX) 2,4 CF-XX XX  
Call Park (  
I
XX) 3  
Park  
Pickup-XX  
Drop  
recommended,  
but not required.  
Call Pickup (  
I
6 XX)  
3. Extension  
number can be  
programmed as  
Auto Dial  
Conference Drop (F 06)  
Contact Closure 1 (F 41) 2  
Contact Closure 2 (F 42) 2  
Direct Line Pickup-Active Line (  
CC1  
CC2  
button.  
4. You can  
program the  
origination  
I
68)  
DLPA  
DLPI  
ExHold  
Direct Line Pickup-Idle Line (  
Exclusive Hold (F 02)  
I
8)  
extension only  
or both the  
origination and  
destination  
extension.  
Fax Management (  
Group Calling-Ring/Page (  
Group Hunt-Ring/Signal ( 77 G or  
Group Pickup ( 66 G)  
Intercom Autodial ( XX or  
Last Number Redial (F 05)  
Loudspeaker Paging ( 70)  
I
XX) 2  
FAX-XX  
GCall-g  
Hunt-g  
P/U Grp-g  
Ext-XX  
I
7 G or  
I
I
*7 G)  
*77 G)  
I
Ext.  
5. You can  
program the  
extension  
number.  
6. Available with  
ACS R2.0 or  
later only.  
I
I
I
*XX) 2  
Intercom  
Intercom  
LNR  
I
Loudspk  
Manual Signaling (F 13 XX or F 13 *XX) 2  
MS-XX  
MsgOff-XX  
Message Light Off (F 10 XX) 5  
Message Light On (F 09 XX) 5  
F
= Feature button  
G = Group  
= Left Intercom  
button  
XX = Extension  
MsgOn-XX  
Recall (F 03)  
Save Number Redial (F 04)  
Recall  
SNR  
In Hybrid mode only, if pool 880 is assigned, these two buttons are associated with this pool.  
(ACS R2.0 or later only)  
I
*
Simultaneous Paging  
Station Lock (F 21) 2  
(I  
* 70)  
SPage  
Lock  
Specify Automatic Line Selection: ________________________________________________________________  
Identify extensions programmed as shown: ___________________________________________________  
Touch-Tone Enable (F 08)  
Voice Mail Messages Button (  
TT-EN  
VMMsgs-777  
VMBox  
I
777)  
Voice Mailbox Transfer (F 14)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
6 of 8  
Form C6: MLS-18D Phone  
Make as many copies as you need. Use template and/or checklist. For additional instructions, see pages 8 through 13.  
Check Desired Features  
Also write in extension or group number  
Automatic System Answer Button {#111} 6  
ASA  
Direct Extension Dial Button {#113} 6  
Night Service Button {#503}  
Outgoing Call Restriction Button {#114} 1  
Wake Up Service Button {#115}  
Caller ID Call Log (F 23) 6  
Caller ID Inspect (F 17)  
DXD  
NightSvc  
OCR  
SAMPLE  
Template Instructions  
• If desired, write in line number, pool access code†, dial code feature, or auto dial number  
• If desired, write in Line Ringing (Imm, Del, or No) from Form B2  
04  
DEL  
IN  
Wake  
Calls  
• If desired, write in Line Access Restriction or Pool Access Restriction†  
(Out, In, or No) from Form B2  
ID-Inspect  
ID-Name  
DND  
Caller ID Name Display (F 16)  
Do Not Disturb (F 01)  
† Available with ACS R2.0 or later only.  
Privacy (F 07)  
Priv  
VMS Cover (F 15)  
VMSCover  
VIOB  
Voice Interrupt on Busy Talk-Back (F 18)  
Account Code Entry (F 12)2  
Background Music (F 19)2  
ACE  
1. Requires Auto  
Dial button for  
Music  
,6  
Call Coverage (F 20 XX XX)2,4  
Cover-XX XX  
each extension.  
Call Forwarding/Call Follow-Me (F 11 XX XX) 2,4 CF-XX XX  
2. Button with  
lights is  
Call Park (  
I
XX) 3  
Park  
Pickup-XX  
Drop  
recommended,  
but not required.  
Call Pickup (  
I
6 XX)  
3. Extension  
number can be  
programmed as  
Auto Dial  
Conference Drop (F 06)  
Contact Closure 1 (F 41) 2  
Contact Closure 2 (F 42) 2  
Direct Line Pickup-Active Line (  
CC1  
CC2  
button.  
I
68)  
DLPA  
DLPI  
ExHold  
4. You can  
program the  
origination  
Direct Line Pickup-Idle Line (  
Exclusive Hold (F 02)  
I
8)  
extension only  
or both the  
origination and  
destination  
extension.  
Fax Management (  
Group Calling-Ring/Page (  
Group Hunt-Ring/Signal ( 77 G or  
Group Pickup ( 66 G)  
Intercom Autodial ( XX or  
Last Number Redial (F 05)  
Loudspeaker Paging ( 70)  
I
XX) 2  
FAX-XX  
GCall-g  
Hunt-g  
P/U Grp-g  
Ext-XX  
I
7 G or  
I
I
*7 G)  
*77 G)  
I
Intercom  
Intercom  
I
5. You can  
program the  
extension  
number.  
6. Available with  
ACS R2.0 or  
later only.  
I
I
*XX) 2  
Ext.  
LNR  
I
Loudspk  
Manual Signaling (F 13 XX or F 13 *XX) 2  
MS-XX  
MsgOff-XX  
Message Light Off (F 10 XX) 5  
Message Light On (F 09 XX) 5  
F
= Feature button  
G = Group  
= Left Intercom  
button  
XX = Extension  
MsgOn-XX  
In Hybrid mode only, if pool 880 is assigned, these two buttons are associated with this pool.  
(ACS R2.0 or later only)  
*
Recall (F 03)  
Save Number Redial (F 04)  
Recall  
SNR  
I
Simultaneous Paging  
Station Lock (F 21) 2  
(I  
* 70)  
SPage  
Lock  
Specify Automatic Line Selection: ________________________________________________________________  
Identify extensions programmed as shown: ___________________________________________________  
Touch-Tone Enable (F 08)  
TT-EN  
Voice Mail Messages Button (  
Voice Mailbox Transfer (F 14)  
I
777)  
VMMsgs-777  
VMBox  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
7 of 8  
Form C7: MLS-12/12D Phone  
Make as many copies as you need. Use template and/or checklist. For additional instructions, see pages 8 through 13.  
Check Desired Features  
Also write in extension or group number  
Automatic System Answer Button {#111} 6  
ASA  
Direct Extension Dial Button {#113} 6  
Night Service Button {#503}  
Outgoing Call Restriction Button {#114} 1  
Wake Up Service Button {#115}  
Caller ID Call Log (F 23) 6  
Caller ID Inspect (F 17)  
DXD  
NightSvc  
OCR  
SAMPLE  
Template Instructions  
• If desired, write in line number, pool access code†, dial code feature, or auto dial number  
• If desired, write in Line Ringing (Imm, Del, or No) from Form B2  
04  
DEL  
IN  
Wake  
Calls  
• If desired, write in Line Access Restriction or Pool Access Restriction†  
(Out, In, or No) from Form B2  
ID-Inspect  
ID-Name  
DND  
Caller ID Name Display (F 16)  
Do Not Disturb (F 01)  
† Available with ACS R2.0 or later only.  
Privacy (F 07)  
Priv  
VMS Cover (F 15)  
VMSCover  
VIOB  
Voice Interrupt on Busy Talk-Back (F 18)  
Account Code Entry (F 12)2  
Background Music (F 19)2  
ACE  
1. Requires Auto  
Dial button for  
Music  
,6  
Call Coverage (F 20 XX XX)2,4  
Cover-XX XX  
each extension.  
Call Forwarding/Call Follow-Me (F 11 XX XX) 2,4 CF-XX XX  
2. Button with  
lights is  
Call Park (  
I
XX) 3  
Park  
Pickup-XX  
Drop  
recommended,  
but not required.  
Call Pickup (  
I
6 XX)  
3. Extension  
number can be  
programmed as  
Auto Dial  
Conference Drop (F 06)  
Contact Closure 1 (F 41) 2  
Contact Closure 2 (F 42) 2  
Direct Line Pickup-Active Line (  
CC1  
CC2  
button.  
I
68)  
DLPA  
DLPI  
ExHold  
4. You can  
program the  
origination  
Direct Line Pickup-Idle Line (  
Exclusive Hold (F 02)  
I
8)  
extension only  
or both the  
origination and  
destination  
extension.  
Fax Management (  
Group Calling-Ring/Page (  
Group Hunt-Ring/Signal ( 77 G or  
Group Pickup ( 66 G)  
Intercom Autodial ( XX or  
Last Number Redial (F 05)  
Loudspeaker Paging ( 70)  
I
XX) 2  
FAX-XX  
GCall-g  
Hunt-g  
P/U Grp-g  
Ext-XX  
I
7 G or  
I
I
*7 G)  
*77 G)  
I
Intercom  
Intercom  
I
5. You can  
program the  
extension  
number.  
6. Available with  
ACS R2.0 or  
later only.  
I
I
*XX) 2  
Ext.  
LNR  
I
Loudspk  
Manual Signaling (F 13 XX or F 13 *XX) 2  
MS-XX  
MsgOff-XX  
Message Light Off (F 10 XX) 5  
Message Light On (F 09 XX) 5  
F
= Feature button  
G = Group  
= Left Intercom  
button  
XX = Extension  
In Hybrid mode only, if pool 880 is assigned, these two buttons are associated with this pool.  
(ACS R2.0 or later only)  
MsgOn-XX  
*
Recall (F 03)  
Save Number Redial (F 04)  
Recall  
SNR  
I
Simultaneous Paging  
Station Lock (F 21) 2  
(I  
* 70)  
SPage  
Lock  
Specify Automatic Line Selection: ________________________________________________________________  
Identify extensions programmed as shown: ___________________________________________________  
Touch-Tone Enable (F 08)  
TT-EN  
Voice Mail Messages Button (  
Voice Mailbox Transfer (F 14)  
I
777)  
VMMsgs-777  
VMBox  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
PAGE  
8 of 8  
Form C8: MLS-6 Phone  
Make as many copies as you need. Use template and/or checklist.  
For additional instructions, see page 8.  
Check Desired Features  
Also write in extension or group number  
SAMPLE  
Template Instructions  
Do Not Disturb (F 01)  
DND  
Priv  
• If desired, write in line number, pool access code†, dial code feature, or auto dial number  
• If desired, write in Line Ringing (Imm, Del, or No) from Form B2  
04  
DEL  
IN  
Privacy (F 07)  
VMS Cover (F 15)  
VMSCover  
VIOB  
• If desired, write in Line Access Restriction or Pool Access Restriction†  
(Out, In, or No) from Form B2  
Voice Interrupt on Busy Talk-Back (F 18)  
Account Code Entry (F 12)1  
ACE  
† Available with ACS R2.0 or later only.  
1. Button with  
Background Music (F 19)1  
Call Coverage (F 20 XX XX)1,2,5  
✔
Music  
lights is  
recommended,  
but not  
✔
Cover-XX XX  
Call Forwarding/Call Follow-Me (F 11 XX XX)1,2 CF-XX XX  
required.  
Call Park  
(I  
XX )3  
Park  
Pickup-XX  
Drop  
2. You can  
program the  
origination  
extension only  
or both the  
origination and  
destination  
extension.  
Call Pickup (  
I
6 XX)  
Conference Drop (F 06)  
Contact Closure 1 (F 41)1  
Contact Closure 2 (F 42)1  
Direct Line Pickup-Active Line (  
CC1  
CC2  
DLPA  
DLPI  
Intercom  
Intercom  
I
68)  
Ext.  
Direct Line Pickup-Idle Line (  
I
8)  
3. Extension  
Exclusive Hold (F 02)  
ExHold  
number can be  
programmed as  
Auto Dial  
Fax Management (  
Group Calling-Ring/Page (  
Group Hunt-Ring/Signal ( 77 G or  
Group Pickup ( 66 G)  
Intercom Autodial ( XX or  
Last Number Redial (F 05)  
Loudspeaker Paging ( 70)  
I
XX) 1  
FAX-XX  
GCall-g  
I
7 G or  
I
I
*7 G)  
*77 G)  
button.  
In Hybrid mode only, if pool 880 is assigned, these two buttons are associated with this pool.  
(ACS R2.0 or later only)  
I
Hunt-g  
P/U Grp-g  
Ext-XX  
4. You can  
*
program the  
extension  
number.  
I
I
I
*XX) 1  
LNR  
5. Available with  
ACS R2.0 or  
later only.  
I
Loudspk  
MS-XX  
MsgOff-XX  
MsgOn-XX  
Manual Signaling (F 13 XX or F 13 *XX) 1  
Message Light Off (F 10 XX) 4  
Message Light On (F 09 XX) 4  
Recall (F 03)  
Recall  
SNR  
Save Number Redial (F 04)  
Simultaneous Paging  
Station Lock(F 21) 1  
(I  
* 70)  
SPage  
Lock  
Touch-Tone Enable (F 08)  
Voice Mail Messages ( 777)  
Voice Mailbox Transfer (F 14)  
TT-EN  
VMMsgs-777  
I
VMBox  
F = Feature button G = Group I = Left Intercom button L = Line XX = Extension  
Specify Automatic Line Selection: ________________________________________________________________  
Identify extensions programmed as shown: ___________________________________________________  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
1 of 3  
Form D: Number Lists  
Required if Form B2 identifies Disallowed or Allowed List Assignments.  
For additional instructions, see page 14.  
Disallowed Phone Number Lists {#404}  
Required only if Disallowed List Assignment {#405} is specified on Form B2.  
Write the telephone numbers that users are prevented from dialing.  
List 1  
List 2  
List 3  
List 4  
List 5  
List 6  
List 7  
List 8  
Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
Allowed Phone Number Lists {#407}  
Required only if Allowed List Assignment {#408} is specified on Form B2.  
Write the telephone numbers that users can dial regardless of assigned restrictions.  
List 1  
List 2  
List 3 List 4 List 5 List 6  
List 7  
List 8  
Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1 Entry Telephone Number1  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
1. Telephone Number can be up to 12 characters, including 0-9, , and #. Write ! for wildcard (press Hold to program).  
*
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PAGE  
2 of 3  
Form D: Number Lists  
Required if Form B1 identifies External Hotlines. For additional  
instructions, see page 15.  
Emergency Phone Number List {#406}  
Write Emergency Phone Numbers that can be  
dialed from any phone that has access to an  
outside line regardless of assigned restrictions.  
External Hotline {#311}  
Required if External Hotline {#311}  
is checked on Form B1.  
Write Extension Jack number specified on  
Form B1, and the corresponding telephone  
number to be assigned to Personal Speed Dial  
Code 80 for that extension.  
Telephone Number1  
Person/Place  
Entry  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
Telephone Number2  
Ext.Jack  
1. Telephone Number can be up to 12 digits (0-9).  
2. Telephone Number can be up to 28 characters, including 0-9, , #, and special dialing functions.  
*
You can have more than 10 External Hotlines.  
NOTE: An External Hotline phone is a standard phone that dials the  
specified telephone number when the handset is lifted.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
Form D: Number Lists  
3 of 3  
Required only if Forced Account Code Verification is desired.  
For additional instructions, see page 15.  
Forced Account Code List {#409}  
Account Code (up to 6 digits)1  
Write Description  
Account Code (up to 6 digits)1  
Write Description  
Account Code (up to 6 digits)1  
Write Description  
Entry  
01  
02  
03  
04  
05  
06  
07  
08  
09  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
Entry  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
65  
66  
Entry  
67  
68  
69  
70  
71  
72  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
85  
86  
87  
88  
89  
90  
91  
92  
93  
94  
95  
96  
97  
98  
99  
1. Valid entries are 0-9; write ! for wildcard (press Hold to program).3 of  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PAGE  
1 of 1  
Form E: System Speed Dial Numbers  
Optional for PARTNER Advanced Communications System. For additional instructions, see page 16.  
To Dial: On system phones, press f + 3-digit code. On standard phones, press # + 3-digit code while receiving intercom dial tone.  
1
*
1
*
1
*
Code  
600  
601  
602  
603  
604  
605  
606  
607  
608  
609  
610  
611  
612  
613  
614  
615  
616  
617  
618  
619  
620  
621  
622  
623  
624  
625  
626  
627  
628  
629  
630  
631  
632  
633  
Name/Company  
Telephone Number2  
Code  
634  
635  
636  
637  
638  
639  
640  
641  
642  
643  
644  
645  
646  
647  
648  
649  
650  
651  
652  
653  
654  
655  
656  
657  
658  
659  
660  
661  
662  
663  
664  
665  
666  
Name/Company  
Telephone Number2  
Code  
667  
668  
669  
670  
671  
672  
673  
674  
675  
676  
677  
678  
679  
680  
681  
682  
683  
684  
685  
686  
687  
688  
689  
690  
691  
692  
693  
694  
695  
696  
697  
698  
699  
Name/Company  
Telephone Number2  
1
2
You can dial System Speed Dial numbers that are marked with at any time, regardless of  
dialing restrictions placed on your extension. System Speed Dial numbers are programmed by the  
System Manager (report problems and suggested revisions to your System Manager).  
Telephone number can be up to 28 digits, including 0-9, , #, and special dialing functions  
(see page 16 of instructions for detailed information).  
*
*
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
518-456-151  
Issue 1  
November 1997  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lexmark Printer Z54 User Manual
Magnavox DVD Player BDP170MW8 User Manual
Master Bilt Refrigerator BGR 14 User Manual
Maytag Range MGR6751BDW User Manual
Maytag Washer W10330943A User Manual
Melissa Blood Pressure Monitor 630 016 User Manual
Melissa Vacuum Cleaner 640 059 User Manual
Mercedes Benz Automobile 2002 SLK 230 Kompressor User Manual
Midland Radio Portable Radio 74 250C User Manual
Midway Games Arctic Thunder User Manual