UDS1100
User Guide
Part Number 900-417
Revision A February 2006
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
UDS1100 User Guide
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
UDS1100 User Guide
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
UDS1100 User Guide
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Figures
Tables
UDS1100 User Guide
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1: Using This Guide
Purpose and Audience
This guide provides the information needed to configure, use, and update the
UDS1100 device server. It is for system administrators and those responsible for
installing and maintaining the UDS.
Chapter Summary
The remaining chapters in this guide include:
Describes the main features of the UDS and the protocols it
supports.
Provides information for installing your unit and getting it up and
running using DeviceInstaller or a serial port connection.
Details using the Web-Manager to set parameters such as port
and server properties.
Provides instructions for accessing Setup Mode (command line
interface) using a Telnet connection through the network or a
terminal or terminal emulation program through the serial port.
Details the network (server) settings
Details the serial port settings.
Details expert and security settings and explains how to reset
the unit to factory default values.
Provides instructions for obtaining the latest firmware and
updating the UDS.
Provides instructions for accessing and using the command line
interface to monitor the network and diagnose problems.
contact Lantronix Technical Support.
Provides descriptions and illustrations of connection
hardware.
Lists technical specifications for the UDS.
BOOTP ARP, and Telnet to assign an IP address.
UDS1100 User Guide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
1: Using This Guide
Provides instructions for converting binary values to
hexadecimals.
Additional Documentation
The following information is available on the product CD or the Lantronix Web site:
UDS1100 Quick Start
Provides the steps for getting the UDS1100 up and
running.
DeviceInstaller Online Help
Provides instructions for using the Windows-based utility
to configure the UDS1100 and other Lantronix device
servers.
“Live” Tutorials on the
Lantronix Web Site (English)
Explain and demonstrate assigning an IP address to the
UDS and setting up the UDS and Com Port Redirector.
Com Port Redirector User
Guide
Provides information on using the Windows-based utility
to create a virtual com port.
UDS1100 User Guide
8
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Introduction
The UDS1100 is a single-port device server that provides a quick, simple, and cost-
effective way to bring the advantages of data accessibility and remote management
to devices not currently connected to a network.
Applications
The UDS family of Device Servers allows serial devices, such as those listed below,
to connect and communicate over Ethernet networks using the IP protocol family
(TCP for connection-oriented stream applications and UDP for datagram
applications).
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
‹
Security alarms
Access control devices
Fire control panels
Time/attendance clocks and terminals
ATM machines
Data collection devices
RFID readers
Universal Power Supply (UPS) management units
Telecommunications equipment
Data display devices
Virtually any asynchronous RS-232, RS422, or RS485 device
Application Examples
Using a method called serial tunneling, the UDS encapsulates serial data into
packets and transports them over Ethernet. Using two UDS units, connected by a
network, virtual serial connections can extend across a facility or around the world.
UDS1100 User Guide
9
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Introduction
Figure 2-1. Serial Tunneling Example
The Com Port Redirector software included on the product CD simplifies the
integration process by extending the functionality of COM-port-based Windows™
applications. Virtual COM ports, mapped to remote device servers on the network,
can replace direct serial connections.
Figure 2-2. Direct TCP/IP or Redirector Configuration
Note: For step-by-step instructions on configuring the UDS for serial tunneling or for
use with the Com Port Redirector, see UDS Configuration Tutorials on the Lantronix
UDS1100 User Guide
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Introduction
Protocol Support
The UDS uses the Internet Protocol (IP) for network communications and the
Transmission Control Protocol (TCP) to assure that no data is lost or duplicated and
that everything sent to the connection arrives correctly at the target.
Supported protocols include:
‹
ARP, UDP, TCP, ICMP, Telnet, TFTP, AutoIP, DHCP, HTTP, and SNMP for
network communications.
‹
‹
‹
‹
TCP, UDP, and Telnet for connections to the serial port.
TFTP for firmware updates.
IP for addressing, routing, and data block handling over the network.
User Datagram Protocol (UDP) for typical datagram applications in which
devices interact with other devices without a point-to-point connection.
Additional Features
Modem Emulation: In modem emulation mode, the UDS can replace dial-up
modems. The unit accepts modem AT commands on the serial port and then
establishes a network connection to the end device. This arrangement leverages
network connections and bandwidth to eliminate dedicated modems and phone lines.
Built-in Web Server: The UDS includes a built-in web server for configuring the unit
and displaying operating and troubleshooting information on the attached links to
online support.
Configuration Methods
After installation, the UDS requires configuration. For the unit to operate correctly on
a network, it must have a unique IP address on the network. There are three basic
methods for logging into the UDS and assigning IP addresses and other configurable
settings:
DeviceInstaller: Configure the IP address and other network settings on the UDS
using a Graphical User Interface (GUI) on a PC attached to a network.
Web-Manager: Through a web browser, configure the UDS settings using the
Serial and Telnet Ports: Use Setup Mode, a command line interface. There are two
approaches to accessing Setup Mode: making a Telnet connection to the network
port (9999) or connecting a terminal (or a PC running a terminal emulation program)
UDS1100 User Guide
11
Download from Www.Somanuals.com. All Manuals Search And Download.
2: Introduction
Product Information Label
The product information label on the underside of the unit contains the following
information about your specific unit:
‹
‹
‹
‹
‹
Bar code
Serial number
Product ID (name)
Product description
Hardware address (also referred to as the Ethernet or MAC address)
The first three bytes of the hardware address are fixed and read 00-20-4A, identifying
the unit as a Lantronix product. The fourth, fifth, and sixth bytes are unique numbers
assigned to each unit.
Figure 2-3. Sample Hardware Address
00-20-4A-14-01-18 or 00:20:4A:14:01:18
UDS1100 User Guide
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
This chapter describes how to get your UDS up and running in the shortest possible
time.
Package Contents
Verify and inspect the contents of the UDS1100 package using the following list. If
any item is missing or damaged, contact your place of purchase immediately.
‹
‹
‹
‹
UDS1100
Six-foot DB9F-to-DB25M modem cable (P/N 500-163 )
Power supply
CD with UDS1100 User Guide and utilities (DeviceInstaller and Com Port
Redirector)
‹
Quick Start Guide
UDS1100 User Guide
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
Installing the UDS
Figure 3-1. UDS1100 Connected to Serial Device and Network
To install the unit:
Complete the following steps in order. Refer to the numbers in the figure above.
Note: See the sections that follow for details about connectors and pinouts.
1. Connect a serial device to your unit.
2. Connect an Ethernet cable to the RJ45 port.
3. Supply power to your unit using the power supply that was included in the
packaging.
Note: The required input voltage is 9-30 VDC (center +) or 10-24 VAC
(1.5W maximum power required).
4. Supply power to the serial device.
diagnostic information.
UDS1100 User Guide
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
Required Information
Before configuring the UDS, have the following information available:
Hardware Address
Take note of the unit’s hardware address (also known as the Ethernet or MAC
address). It is on the product label, in the format: 00-20-4a-XX-XX-XX, where the XXs
Hardware Address: 00-20-4a-_____-_____-_____
IP Address
The UDS must have a unique IP address on your network. This address references
the specific unit. By default, the unit is DHCP-enabled and automatically assigned an
IP address on DHCP-enabled networks. If you are assigning a static IP address, the
systems administrator generally provides the IP address, subnet mask, and gateway.
Note: The factory default IP address is 0.0.0.0 to enable DHCP, BOOTP,
and AutoIP. When the units boots, it sends a DHCP broadcast to try and get
an IP address. If it receives no reply from a DHCP server, the UDS tries
BOOTP. If the UDS does not receive a response from BOOTP, it reverts to
an AutoIP address.
IP Address:
_______ _______ _______ _______
Subnet Mask: _______ _______ _______ _______
Gateway:
_______ _______ _______ _______
You have several options for assigning an IP address and related network settings to
your unit. This chapter provides information about using the DeviceInstaller (graphical
user interface) and serial port login (command line interface) methods.
Note: For information about other methods of assigning the IP address, such
as DHCP, AutoIP, ARP, and Telnet, see A: Alternative Ways to Assign an IP
UDS1100 User Guide
15
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
Assigning the IP Address: DeviceInstaller
This chapter covers the steps for getting the UDS1100 device server online and for
viewing its current configuration.
Note: DeviceInstaller online Help provides more detailed information on
using DeviceInstaller.
Installing DeviceInstaller
To use the DeviceInstaller utility, first install it from the product CD.
1. Insert the product CD into your CD-ROM drive. The Lantronix UDS1100
DeviceInstaller window displays.
2. If the CD does not launch automatically:
a) Click the Start button on the Task Bar and select Run.
b) Enter your CD drive letter, colon, backslash, Launch.exe (e.g.,
D:\Launch.exe).
3. Click the DeviceInstaller button.
4. Respond to the installation wizard prompts. (When prompted to select an
installation type, select Typical.)
Assigning an IP Address
The unit’s IP address must be configured before it can work correctly on a network.
The unit’s IP address is normally set to 0.0.0.0 at the factory. The hardware address
is on the product label. The unit is DHCP enabled as the default.
To assign an IP address manually:
1. Click StartÆPrograms Æ LantronixÆDeviceInstallerÆDeviceInstaller. If your
PC has more than one network adapter, a message displays. Select an adapter
and click OK.
Note: If the unit already has an IP address (e.g., DHCP has assigned an
IP address), click the Search icon
and select the unit from the list of
Lantronix device servers on the local network.
2. Click the Assign IP icon
.
3. If prompted, enter the hardware address (on the product label) and click Next.
4. Select Assign a specific IP address and click Next.
5. Enter the IP address. The Subnet mask displays automatically based on the IP
address; if desired, you may change it. On a local network, you can leave the
Default gateway blank (all zeros). Click Next.
6. Click the Assign button and wait several seconds until a confirmation message
displays. Click Finish.
UDS1100 User Guide
16
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
7. Select the device from the main window list and select Ping from the Tools
menu. The Ping Device dialog box shows the IP address of the selected unit.
8. From the Tools menu, click the Ping button. The results display in the Status
window. Click the Clear Status button to clear the window so you can ping the
device again.
Note: If you do not receive “Reply” messages, make sure the unit is
attached to the network properly and the IP address assigned is valid for
the particular network segment you are working with. If you are not sure,
check with your systems administrator.
9. Click the Close button to close the dialog box and return to the main window.
Adding the Unit to the Manage List
Now add the unit to the list of similar Lantronix devices on the network so you can
manage and configure it. To perform this step, click the Search icon
DeviceInstaller locates the unit and adds it to the list. Now you can manage
(configure) the unit so it works with the serial device on the network.
Accessing the UDS1100 Using DeviceInstaller
1. Click StartÆPrograms Æ LantronixÆDeviceInstallerÆDeviceInstaller.
2. Click the UDS1100 folder. The list of available Lantronix UDS1100 devices
displays.
3. Expand the list of UDS1100s by clicking the + symbol next to the UDS1100 icon.
Select the UDS1100 unit by clicking on its IP address to view its configuration.
Viewing the Current Configuration
DeviceInstaller provides a view of the unit's configuration.
To view the unit's current settings:
1. Follow the instructions above to locate the UDS1100.
2. In the right pane, click the Device Details tab. The current UDS1100
configuration displays:
Name
Configurable field. A name that identifies the UDS1100.
Double-click the field, type in the value, and press Enter to
complete. This name is not visible on other PCs or laptops
using DeviceInstaller.
Group
Configurable field. A group name to categorize the UDS1100.
Double-click the field, type in the value, and press Enter to
complete. This group name is not visible on other PCs or
laptops using DeviceInstaller.
Comments
Device Family
Configurable field. Information about the UDS1100. Double-
click the field, type in the value, and press Enter to complete.
This description or comment is not visible on other PCs or
laptops using DeviceInstaller.
Non-configurable field. Displays the UDS1100’s device family
type as UDS1100.
UDS1100 User Guide
17
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
Type
ID
Non-configurable field. Displays the device type as UDS1100.
Non-configurable field. Displays the UDS1100’s ID embedded
within the box.
Hardware Address
Firmware Version
Non-configurable field. Displays the UDS1100’s hardware (or
MAC) address.
Non-configurable field. Displays the firmware currently
installed on the UDS1100.
Extended Firmware
Version
Non-configurable field. Displays the full version nomenclature
of the firmware.
Online Status
Non-configurable field. Displays the UDS1100’s status as
online, offline, unreachable (the UDS1100 is on a different
subnet), or busy (the UDS1100 is currently performing a task).
Telnet Enabled
Telnet Port
Non-configurable field. Permits Telnet sessions.
Non-configurable field. Displays the UDS1100’s port for telnet
sessions.
Web Enabled
Web Port
Non-configurable field. Permits configuration through Web-
Manager.
Non-configurable field. Displays the UDS1100’s port for Web-
Manager configuration.
Maximum Baud Rate
Supported
Non-configurable field. Displays the UDS1100’s maximum
baud rate.
Note: The UDS1100 may not currently be running at this rate.
Firmware Upgradeable
IP Address
Non-configurable field. Displays True, indicating the
UDS1100’s firmware is upgradeable as newer version
become available.
Non-configurable field. Displays the UDS1100’s current IP
address. To change the IP address, see Assigning an IP
Number of COB partitions
supported
Non-configurable field. Displays the number of COB partitions
supported.
Supports Dynamic IP
Subnet Mask
Gateway
Non-configurable field. Indicates whether the current IP
address on the UDS1100 was set manually or assigned by
DHCP.
Non-configurable field. Displays the UDS1100’s current
subnet mask. To change the subnet mask, see Assigning an
Non-configurable field. Displays the UDS1100’s current
gateway. To change the gateway, see Assigning an IP
Number of Ports
TCP Keepalive
Non-configurable field. Displays the number of ports on the
UDS1100.
Non-configurable field. Displays the UDS1100’s TCP
keepalive value. The value is in the range 1-65s, and the
default setting is 45.
UDS1100 User Guide
18
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
Supports Configurable
Pins
Non-configurable field. Displays False.
Supports Email Triggers
Non-configurable field. Displays False.
Supports AES Data
Stream
Non-configurable field. Displays False.
Supports 485
Non-configurable field. Displays True. The UDS1100 supports
the RS-485 protocol.
Supports 920K Baudrate
Non-configurable field. Displays False. UDS1100 supports
baud rates up to 230 Kbaud.
Supports HTTP Server
Supports HTTP Setup
Supports 230K Baud Rate
Non-configurable field. Displays True.
Non-configurable field. Displays True.
Non-configurable field. UDS1100 supports a baud rate of 230
Kbaud.
Next Step
Now that the UDS has an IP address and other initial settings, you can configure it.
1. Double-click the unit in the list. Details about the unit display.
2. You have the following options:
‹
To configure the unit using a Web browser, click the Web Configuration tab.
The Lantronix Web-Manager window displays in your browser. Continue with 4:
Note: To assign Expert and Security settings, you must use the Setup
Mode window in a Telnet session.
‹
To configure the unit using a Telnet session, click the Telnet Configuration
tab. The Setup Mode window displays. Continue with 5: Configuration via
.
Assigning the IP Address: Serial Port Login
To assign the IP address and other network settings using a serial connection:
1. Connect a console terminal or a PC running a terminal emulation program to the
unit's serial port. The default serial port settings are 9600 baud, 8 bits, no
parity, 1 stop bit, no flow control.
2. To enter Setup Mode, cycle the unit's power (power off and back on). After
power-up, the self-test begins and the red Diagnostic LED starts blinking. You
have one second to enter three lowercase x characters.
Note: The easiest way to enter Setup Mode is to hold down the x key at
the terminal (or emulation) while powering up the unit.
3. Select 0 (Server Configuration) and follow the prompts until you get to
IP address.
4. Enter the new IP address, subnet mask, and gateway (if applicable).
UDS1100 User Guide
19
Download from Www.Somanuals.com. All Manuals Search And Download.
3: Getting Started
5. Do one of the following:
‹
‹
Continue with 5: Configuration via Telnet or Serial Port (Setup Mode).
Select 9 to save and exit Setup Mode. The unit performs a power reset.
UDS1100 User Guide
20
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
You must configure the unit so it can communicate on a network with your serial
device. For example, you must set the way the unit will respond to serial and network
traffic, how it will handle serial packets, and when to start or close a connection.
The unit’s configuration is stored in nonvolatile memory and is retained without
power. You can change the configuration at any time. The unit performs a reset after
you change and store the configuration.
In this chapter, we describe how to configure the UDS1100 using Web-Manager,
Lantronix’s browser-based configuration tool. (For information on using Setup Mode,
our command line configuration interface, see 5: Configuration via Telnet or Serial
Note: The examples in this section show a typical device. Your device may have
different configuration options.
Accessing UDS1100 Using DeviceInstaller
Note: Make note of the hardware (MAC) address. You will need it to locate
the UDS1100 using DeviceInstaller. For more information on the hardware
Follow the instructions on the product CD to install and run DeviceInstaller.
1. Click StartÆPrograms Æ LantronixÆDeviceInstallerÆDeviceInstaller. If the
PC has more than one network adapter, a message displays requesting the
selection of a network adapter. Select an adapter and click OK.
2. Click the Search icon
. The list of Lantronix device servers displays in the
left pane.
3. Click the UDS folder. The list of available UDS products displays.
4. Expand the list of UDS1100s by clicking the + symbol next to the UDS1100 icon.
5. Select the UDS1100 unit by clicking its hardware address.
6. In the right pane, click the Web Configuration tab.
7. To view the UDS1100’s Web-Manager in the current DeviceInstaller window,
click the Go button. To open the Web-Manager in a web browser, click the
External Browser button. The Web-Manager displays.
Note: Alternatively, to open Web-Manager, open your web browser and
enter the IP address of the UDS1100.
UDS1100 User Guide
21
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Figure 4-1. Lantronix Web-Manager
The main menu is in the left pane of the Web-Manager window.
Network Configuration
The unit’s network values display when you select Network from the main menu. The
following sections describe the configurable parameters on the Network Settings
page.
Figure 4-2. Network Settings
UDS1100 User Guide
22
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Automatic IP Address Configuration
An IP address can be assigned automatically. You then enter related network
settings.
To assign an IP address automatically:
1. On the main menu, click Network.
2. Select Obtain IP address automatically.
3. Enter the following (as necessary):
BOOTP
Select Enable to permit the Bootstrap Protocol (BOOTP)
server to assign the IP address from a pool of addresses
automatically. Enable is the default.
DHCP
Select Enable to permit the Dynamic Host Configuration
Protocol (DHCP) to assign a leased IP address to the
UDS1100 unit automatically. Enable is the default.
AutoIP
Select Enable to permit the UDS1100 to generate an IP in the
169.254.x.x address range with a Class B subnet. Enable is
the default.
DHCP Host Name
Enter the name of the host on the network providing the IP
address.
Note: Disabling BOOTP, DHCP, and AutoIP (all three checkboxes) is not
advised as the only available IP assignment method will then be ARP or
serial port.
4. When you are finished, click the OK button.
5. On the main menu, click Apply Settings.
Static IP Address Configuration
You can manually assign an IP address to the unit and enter related network
settings.
To assign an IP address manually:
1. On the main menu, click Network.
2. Select Use the following IP configuration.
3. Enter the following (as necessary):
IP Address
If DHCP is not used to assign IP addresses, enter it manually
in decimal-dot notation. The IP address must be set to a
unique value in the network.
Subnet Mask
A subnet mask defines the number of bits taken from the IP
address that are assigned for the host part.
Default Gateway
The gateway address, or router, allows communication to
other LAN segments. The gateway address should be the IP
address of the router connected to the same LAN segment as
the unit. The gateway address must be within the local
network.
UDS1100 User Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
4. When you are finished, click the OK button.
5. On the main menu, click Apply Settings.
Ethernet Configuration
You must specify the speed and direction of data transmission.
To specify how data will be transmitted:
1. On the main menu, click Network.
2. Enter the following (as necessary):
Auto Negotiate
With this option, the Ethernet port auto-negotiates the speed
and duplex with the hardware endpoint to which it is
connected. This is the default.
If this option is not selected, complete the fields that become
available:
‹
‹
Speed: The speed of data transmission. The default
setting is 100 Mbps.
Duplex: The direction of data transmission. The
default setting is Full.
3. When you are finished, click the OK button.
4. On the main menu, click Apply Settings.
Server Configuration
The unit’s server values display when you select Server from the main menu. The
following sections describe the configurable parameters on the Server Settings page.
UDS1100 User Guide
24
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Figure 4-3. Server Settings
To configure the UDS1100’s device server settings:
1. On the main menu, click Server.
2. Configure or modify the following fields:
Server Configuration
Telnet Password
Retype Password
Enter the password required for Telnet access.
Re-enter the password required for Telnet access.
Advanced
ARP Cache Timeout
(secs)
When the unit communicates with another device on the
network, it adds an entry into its ARP table. ARP Cache
timeout defines the number of seconds (1-600) before it
refreshes this table.
TCP Keepalive (secs)
Monitor Mode @ Bootup
HTTP Server Port
TCP Keepalive time defines how many seconds the unit waits
during an inactive connection before checking its status. If the
unit does not receive a response, it drops that connection.
Enter a value between 0 and 60 seconds. 0 disables
keepalive. The default setting is 45.
Select Disable to disable entry into the monitor mode using
the yyy or xx1 key sequence at startup. This field prevents
the unit from entering monitor mode by interpreting the stream
of characters that are received during the device server's
initialization at startup. The default setting is Enable.
This option allows the configuration of the web server port
number. The valid range is 1-65535. The default setting is 80.
UDS1100 User Guide
25
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
MTU Size
The Maximum Transmission Unit (MTU) is the largest physical
packet size a network can transmit for TCP and UDP. Enter
between 512 and 1400 bytes. The default setting is 1400
bytes.
3. When you are finished, click the OK button.
4. On the main menu, click Apply Settings.
Host List Configuration
The UDS1100 scrolls through the host list until it connects to a device listed in the
host list table. After a successful connection, the unit stops trying to connect to any
others. If this connection fails, the unit continues to scroll through the table until the
next successful connection.
The host list supports a minimum of 1 and a maximum of 12 entries. Each entry
contains an IP address and a port number.
Note: The host list is disabled for Manual and Modem Mode. The unit does
not accept a data connection from a remote device when the hostlist option is
enabled.
To configure the host list:
1. On the main menu, click Hostlist.
Figure 4-4. Hostlist Settings
2. Enter or modify the following fields:
Retry Settings
Retry Counter
Enter the value for the number of times the UDS1100 should
attempt to retry connecting to the host list. The default setting
is 3.
UDS1100 User Guide
26
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Retry Timeout
Enter the duration (in seconds) the UDS1100 should abandon
attempting a connection to the host list. The default setting is
250.
Host Information
Host Address
Port
Enter or modify the host’s IP address.
Enter the target port number.
3. When you are finished, click the OK button.
4. On the main menu, click Apply Settings.
Channel 1 Configuration
The Channel 1 configuration defines how the serial port responds to network and
serial communication.
Serial Settings
To configure the channel’s serial settings:
1. On the main menu, click Serial Settings (under Channel 1) to display the Serial
Settings window.
Figure 4-5. Channel Serial Settings
2. In the available fields, enter the following information:
UDS1100 User Guide
27
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Channel 1
Disable Serial Port
When selected, disables communication through the serial
port. The serial port is enabled by default.
Note: This feature is not available on single port device
servers.
Port Settings
Protocol
From the drop-down menu, select the protocol type for the
selected channel. The default setting is RS232.
Flow Control
Baud Rate
Flow control manages data flow between devices in a network
to ensure it is processed efficiently. Too much data arriving
before a device is prepared to manage it causes lost or
retransmitted data. None is the default.
The unit and attached serial device, such as a modem, must
agree on a speed or baud rate to use for the serial connection.
Valid baud rates are 300, 600, 1200, 2400, 4800, 9600
(default), 19200, 38400, 57600, 115200, and 230400 baud.
The default setting is 9600.
Data Bits
Indicates the number of bits in a transmitted data package.
The default setting is 8.
Parity
Checks for the parity bit. The default setting is None.
Stop Bits
The stop bit follows the data and parity bits in serial
communication. It indicates the end of transmission. The
default setting is 1.
Pack Control
Enable Packing
Select to enable packing on the UDS1100.
Two firmware-selectable packing algorithms define how and
when packets are sent to the network.
The standard algorithm is optimized for applications in which
the unit is used in a local environment, allowing for very small
delays for single characters, while keeping the packet count
low.
The alternate packing algorithm minimizes the packet count
on the network and is especially useful in applications in a
routed Wide Area Network (WAN). Adjusting parameters in
this mode can economize the network data stream.
Disabled by default.
Idle Gap Time
Select the maximum time for inactivity. The default time is
12 milliseconds.
Match 2 Byte Sequence
Use to indicate the end of a series of data to be sent as one
group. The sequence must occur sequentially to indicate end
of the data collection to the UDS1100. The default setting is
No.
UDS1100 User Guide
28
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Match Bytes
Use to indicate the end of a series of data to be sent as one
group. Set this value to 00 if specific functions are not needed.
Send Frame Only
After the detection of the byte sequence, indicates whether to
send the data frame or the entire buffer. Select Yes to send
only the data frame. The default setting is No.
Send Trailing Bytes
Select the number of bytes to send after the end-of-sequence
characters. The default setting is None.
Flush Input Buffer (Serial to Network)
With Active Connect
Select Yes to clear the input buffer with a connection that is
initiated from the device to the network. The default setting is
No.
With Passive Connect
At Time of Disconnect
Select Yes to clear the input buffer with a connection initiated
from the network to the device. The default setting is No.
Select Yes to clear the input buffer when the network
connection to or from the device is disconnected. The default
setting is No.
Flush Output Buffer (Network to Serial)
With Active Connect
Select Yes to clear the output buffer with a connection that is
initiated from the device to the network. The default setting is
No.
With Passive Connect
At Time of Disconnect
Select Yes to clear the output buffer with a connection initiated
from the network to the device. The default setting is No.
Select Yes to clear the output buffer when the network
connection to or from the device is disconnected. The default
setting is No.
3. When you are finished, click the OK button.
4. On the main menu, click Apply Settings.
Connection Settings - TCP
To configure a channel’s TCP settings:
1. On the main menu, click Connection. The Connection Settings window for the
channel displays.
UDS1100 User Guide
29
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Figure 4-6. TCP Connection Settings
2. In the available fields, enter or modify the following information:
Connect Protocol
Protocol
From the drop-down menu, select TCP.
Connect Mode: Passive Connection
Accept Incoming
Select Yes to accept incoming connections. The default
setting is Yes.
Password Required
Determines whether a password is required for an incoming
passive connection. This field is not available when a
password is set for Telnet mode. The default setting is No.
Password
If Password Required was set to Yes, enter the password for
passive connections.
UDS1100 User Guide
30
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Connect Mode: Active Connection
Active Connect
Select None (default) to disable Active Connect. Otherwise,
indicate the connection type from the drop-down list:
‹
‹
With Any Character: Attempts to connect when any
character is received from the serial port.
With Active Mdm Ctrl In: Accepts external
connection requests only when the
modem_control_in input is asserted.
‹
‹
‹
With Start Character: Attempts to connect when it
receives a specific start character from the serial
port. The default start character is carriage return.
Manual Connection: Attempts to connect when
directed by a command string received from the
serial port.
Auto Start: Automatically connects to the remote IP
address and port after booting up.
Start Character
Modem Mode
If Active Connect is set to With Start Character, enter the
start character in this field. The default setting is 0D.
Indicates the on-screen response type when in Modem Mode
(if Modem Mode is enabled). The default setting is None.
Endpoint Configuration
Local Port
Enter the local port number.
Auto increment for active
connect
Select to auto-increment the local port number for new
outgoing connections. The range of auto-incremented port
numbers is 50,000 to 59,999 and loops back to the beginning
when the maximum range is reached. Disabled by default.
Remote Port
Remote Host
Enter the remote port number.
Enter the IP address of the remote device.
Common Options
Telnet Mode
This field is available for configuration only when Active
Connect is set to None. Select Enable to permit Telnet
communication to the UDS1100 unit.
Terminal Name
This field is available for configuration only when Telnet Mode
is set to Enable.
Use the terminal name for the Telnet terminal type. Enter only
one name. When this option is enabled, the unit also reacts to
the end of record (EOR) and binary options, which can be
used for applications such as terminal emulation to IBM hosts.
Connect Response
A single character is transmitted to the serial port when there
is a change in connection state. The default setting is None.
UDS1100 User Guide
31
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Use Hostlist
If this option is set to True, the device server scrolls through
the host list until it connects to a device listed in the host list
table. Once it connects, the unit stops trying to connect to any
others. If this connection fails, the unit continues to scroll
through the table until it connects to another IP in the host list.
The host list is disabled for Manual Mode and for Modem
Mode. The unit will not accept a data connection from a
remote device when the host list option is enabled.
LED
Select Blink for the status LEDs to blink upon connection or
None for no LED output. The default setting is Blink.
Disconnect Mode
On Mdm_Ctrl_In Drop
Set to Yes for the network connection to or from the serial port
to drop when modem_control_in (DSR) transitions from a
high state to a low state. The default setting is No.
Hard Disconnect
With EOT
When set to Yes, the TCP connection closes even if the
remote site does not acknowledge the disconnect request.
Select Yes to drop the connection when Ctrl-D or Hex 04 is
detected. Both Telnet Mode and Disconnect with EOT must
be enabled for Disconnect with EOT to function properly.
Ctrl+D is only detected going from the serial port to the
network. The default setting is No.
Inactivity Timeout
Use this parameter to set an inactivity timeout. The unit drops
the connection if there is no activity on the serial line before
the set time expires. Enter time in the format mm:ss, where m
is the number of minutes and s is the number of seconds. To
disable the inactivity timeout, enter 00:00.
3. When you are finished, click the OK button.
4. On the main menu, click Apply Settings.
Connection Settings - UDP
To configure a channel’s UDP settings:
1. On the main menu, click Connection. The Connection Settings window for the
selected channel displays.
2. In the available fields, enter or modify the following information:
UDS1100 User Guide
32
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Figure 4-7. UDP Connection Settings
Connect Protocol
Protocol
Select UDP from the drop-down menu.
Datagram Mode
Datagram Type
Configures the remote IP or network broadcast address and
the remote port. Enter 01 for directed or broadcast UDP. The
default setting is 00.
Accept Incoming
Select Yes to accept incoming UDP datagrams. The default
setting is Yes.
Endpoint Configuration
Local Port
Enter the local port number.
Remote Port
Enter the port number of the remote device.
Enter the IP address of the remote device.
Remote Host
UDS1100 User Guide
33
Download from Www.Somanuals.com. All Manuals Search And Download.
4: Configuration Using Web-Manager
Device Address Table
The table is enabled when Datagram Type is set to FD. Enter
values between 1 and 255 to identify units on the local
network of device servers.
Note: Lantronix Tech Support supports Datagram type 01.
Datagram Type FD is for OEM use.
3. When you are finished, click the OK button.
4. On the main menu, click Apply Settings.
Apply Settings
1. To save and apply the configuration changes to the device server, click the
Apply Settings button.
Note: Clicking OK on each page does not change the configuration on the device.
OK tells the UDS1100 what changes to use; Apply Settings makes the changes
permanent and reboots the UDS1100.
Apply Factory Defaults
1. Click the Apply Defaults button to set the device server back to the default
2. Click Yes to set factory settings, or click No to cancel.
UDS1100 User Guide
34
Download from Www.Somanuals.com. All Manuals Search And Download.
5: Configuration via Telnet or Serial Port
(Setup Mode)
You must configure the unit so it can communicate on a network with your serial
device. As an alternative to using a web browser, as described in the previous
chapter, you can use the following procedures remotely or locally:
‹
‹
Use a Telnet connection to configure the unit over the network.
Use a terminal or terminal emulation program to access the serial port locally.
The series of prompts at which you enter configuration settings is called Setup
Mode.
Note: Detailed information about other setup methods is available from your
Lantronix Sales Associate.
The unit’s configuration is stored in nonvolatile memory and is retained without
power. You can change the configuration at any time. The unit performs a reset after
the configuration has been changed and stored.
This chapter tells you how to access Setup Mode and the general procedure for
using it. To complete the configuration, continue with 6: Setup Mode: Server
Note: The menus in the configuration chapters show a typical device. Your
device may have different configuration options.
Accessing Setup Mode
Telnet Connection
To configure the unit over the network, establish a Telnet connection to port 9999.
Note: You can also use DeviceInstaller to access Telnet. Select the device
from the main window list, and click the Telnet Configuration tab. Skip
steps 1 and 2.
To establish a Telnet connection:
1. From the Windows Start menu, click Run and type the following command,
where x.x.x.x is the IP address, and 9999 is the unit’s fixed network configuration
port number:
Windows: telnet x.x.x.x 9999
UNIX: telnet x.x.x.x:9999
2. Click OK. The following information displays.
UDS1100 User Guide
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5: Configuration via Telnet or Serial Port (Setup Mode)
Figure 5-1. MAC Address
3. To enter Setup Mode, press Enter within 5 seconds. The configuration settings
display, followed by the Change Setup menu.
Figure 5-2. Setup Menu Options
4. Select an option on the menu by entering the number of the option in the Your
choice ? field and pressing Enter.
5. To enter a value for a parameter, type the value and press Enter, or to confirm a
current value, just press Enter.
6. When you are finished, save the new configuration (option 9). The unit reboots.
Serial Port Connection
To configure the unit through a serial connection:
1. Connect a console terminal or PC running a terminal emulation program to your
unit's serial port. The default serial port settings are 9600 baud, 8 bits, no
parity, 1-stop bit, no-flow control.
2. Reset the UDS1100 unit by cycling the unit's power (turning the power off and
back on). Immediately upon resetting the device, enter three lowercase x
characters (xxx).
Note: The easiest way to enter Setup Mode is to hold down the x key at
the terminal (or emulation) while resetting the unit. You must do this
within three seconds of resetting the UDS1100.
At this point, the screen display is the same as when you use a Telnet connection. To
Exiting Setup Mode
To exit setup mode:
You have two options:
‹
To save all changes and reboot the device, select option 9 Save and exit from
the Change Setup menu. All values are stored in nonvolatile memory.
‹
To exit the configuration mode without saving any changes or rebooting. select
option 8 Exit without save from the Change Setup menu.
UDS1100 User Guide
36
Download from Www.Somanuals.com. All Manuals Search And Download.
6: Setup Mode: Server Configuration
This chapter explains how to configure the network settings.
Note: Current values display in parentheses.
Server Configuration (Option 0)
The unit’s basic network parameters display when you select Server configuration
(option 0). The IP Address, Set Gateway IP Address, and Netmask fields display
the current values.
Figure 6-1. Network Settings
IP Address : (000) .(000) .(000) .(000)
Set Gateway IP Address (N)
Netmask: Number of Bits for Host Part (0=default) (0)
Change telnet config password (N)
IP Address
If DHCP is not used to assign IP addresses, enter the IP address manually. The IP
address must be set to a unique value in the network. Enter each octet and press
Enter between each section. The current value displays in parentheses.
IP Address : (000) (000) (000) (000) _
If DHCP is used, the third octet of the IP address sets the BootP/DHCP/AutoIP
options. The following table shows the bits you can manually configure to force the
UDS1100 to disable AutoIP, DHCP, or BootP. To disable an option, set the
appropriate bit.
Table 6-1. BootP/DHCP/AutoIP options
Value
Options
Bit
AutoIP
0
1
2
1
2
4
DHCP
BootP
For example, if the third octet is 0.0.5.0, the AutoIP and BootP options are
disabled; only DHCP is enabled. (The value 5 results from adding the binary
equivalents of 0 and 2.) This is the most common setting when using DHCP.
Set Gateway IP Address
The gateway address, or router, allows communication to other LAN segments. The
gateway address should be the IP address of the router connected to the same LAN
segment as the unit. The gateway address must be within the local network. The
UDS1100 User Guide
37
Download from Www.Somanuals.com. All Manuals Search And Download.
6: Setup Mode: Server Configuration
default setting is N (No), meaning the gateway address has not been set. To set the
gateway address, type Y and enter the address.
Set Gateway IP Address (N) ? Y
Gateway IP addr (000) (000) (000) (000)_
Netmask: Number of Bits for Host Part
A netmask defines the number of bits taken from the IP address that are assigned for
the host part.
Netmask: Number of Bits for Host Part (0=default) (0) _
Note: Class A: 24 bits; Class B: 16 bits; Class C: 8 bits
The unit prompts for the number of host bits to be entered, then calculates the
netmask, which appears in standard decimal-dot notation (for example,
255.255.255.0) when the saved parameters display. The default setting is 0.
Table 6-2. Standard IP Network Netmasks
Network Class
Host Bits
Netmask
A
B
C
24
16
8
255.0.0.0
255.255.0.0
255.255.255.0
Change Telnet Configuration Password
Setting the Telnet configuration password prevents unauthorized access to the setup
menu through a Telnet connection to port 9999 or through web pages. The password
must have 4 characters. The default setting is N (No).
Figure 6-2. Change Telnet Configuration Password
Change telnet config password (N) ? _
An enhanced password setting (for Telnet access only) of 16 characters is available
Note: You do not need a password to access the Setup Mode window by a
serial connection.
DHCP Name
If a DHCP server has automatically assigned the IP address and network settings,
you can discover the unit by using the DeviceInstaller network search feature or
Note: When you enter Monitor Mode from the serial port with network
connection enabled and issue the NC (Network Communication) command,
you see the unit’s IP configuration.
UDS1100 User Guide
38
Download from Www.Somanuals.com. All Manuals Search And Download.
6: Setup Mode: Server Configuration
There are three methods for assigning DHCP names to the unit.
‹
Default DHCP Name: If you do not change the DHCP name, and you are
using an IP of 0.0.0.0, then the DHCP name defaults to XX.XX.XX.XX
(XXXXXX is the last 6 digits of the MAC address shown on the label on the
bottom/side of the unit). For example, if the MAC address is 00-20-4A-12-34-
56, then the default DHCP name is C123456.
‹
Custom DHCP Name: You can create your own DHCP name. If you are using
an IP address of 0.0.0.0, then the last option in Server configuration is Change
DHCP device name. This option allows you to change the DHCP name to an
alphanumeric name (LTX in our example).
Change DHCP device name (not set) ? (N) Y
Enter new DHCP device name : LTX
‹
Numeric DHCP Name: You can change the DHCP name by specifying the last
octet of the IP address. When you use this method, the DHCP name is LTXYY
where YY is what you chose for the last octet of the IP address. If the IP
address you specify is 0.0.0.12, then the DHCP name is LTX12. This method
only works with 2 digit numbers (01-99).
UDS1100 User Guide
39
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
This chapter explains how to configure the serial port.
Notes:
‹
‹
Current values display in parenthesis.
You must enter some values in hexadecimal notation. (See B: Binary to
Channel 1 (Option 1)
Select Channel 1 (option 1) from the Change Setup menu to define how the serial
port responds to network and serial communications. The following sections describe
the configurable parameters within the Channel configuration menu.
Figure 7-1. Serial Port Settings
Baudrate
The unit and attached serial device, such as a modem, must agree on a speed or
baud rate to use for the serial connection. Valid baud rates are 300, 600, 1200, 2400,
4800, 9600 (default), 19200, 38400, 57600, 115200, and 230400 baud.
Baudrate (9600) ? _
UDS1100 User Guide
40
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
I/F (Interface) Mode
The Interface (I/F) Mode is a bit-coded byte entered in hexadecimal notation. The
default setting is 4C.
Figure 7-2. Interface Mode
I/F Mode (4C) ? _
The following table displays available I/F Mode options:
Note: All bit positions in the table that are blank represent “don’t care” bits
for that particular option, which can be set to either a 0 or 1 value.
Table 7-1. Interface Mode Options
I/F Mode Option
RS-232C
7
6
5
4
3
2
1
0
0
0
(1)
RS-422/485 4-wire
RS-485 2-wire
7 Bit
0
1
1
1
1
1
0
1
8 Bit
No Parity
0
1
0
0
1
1
Even Parity
Odd Parity
1 stop bit
0
1
1
2 stop bits(1)
1
(1)
2 stop bits are implemented by the software. This might influence performance.
The following table demonstrates how to build some common Interface Mode
settings:
Table 7-2. Common Interface Mode Settings
Common I/F Mode Setting
Binary
Hex
RS-232C, 8-bit, No Parity, 1 stop bit
0100 1100
4C
RS-232C, 7-bit, Even Parity, 1 stop bit
RS-485 2-wire, 8-bit, No Parity, 1 stop bit
RS-422, 8-bit, Odd Parity, 1 stop bit
0111 1000
0100 1111
0101 1101
78
4F
5D
Flow
Flow control sets the local handshaking method for stopping serial input/output. The
default setting is 00.
Flow (00) ? _
UDS1100 User Guide
41
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Use the following table to select flow control options:
Table 7-3. Flow Control Options
Flow Control Option
Hex
00
No flow control
XON/XOFF flow control
01
Hardware handshake with RTS/CTS lines 02
XON/XOFF pass characters to host 05
Port Number
The setting represents the source port number in TCP connections. It is the number
that identifies the channel for remote initiating connections.
Port No (10001) ? _
The default setting for Port 1 is 10001. The range is 1-65535, except for the following
reserved port numbers:
Table 7-4. Reserved Port Numbers
Port Numbers Reserved for
1 – 1024
9999
Reserved (well known ports)
Telnet setup
14000-14009
30704
Reserved for Redirector
Reserved (77F0h)
30718
Reserved (77FEh)
Warning: We recommend that you not use the reserved port numbers
for this setting as incorrect operation may result.
Use Port 0 for the outgoing local port to change with each connection. The port range
is 50,000-59,999. Each subsequent connection increments the number by 1 (it wraps
back around to 50,000).
Only use this automatic port increment feature to initiate a connection using TCP. Set
the port to a non-zero value when the unit is in a passive mode or when using UDP
instead of TCP.
Connect Mode
Connect Mode defines how the unit makes a connection, and how it reacts to
incoming connections over the network.
ConnectMode (C0) ? _
Enter Connect Mode options in hexadecimal notation. The default setting is C0.
Note: All bit positions in the table that are blank represent “don’t care” bits for
that particular option, which can be set to either a 0 or 1 value.
UDS1100 User Guide
42
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Table 7-5. Connect Mode Options
Connect Mode Option
7
6
5
4
3
2
1
0
a) Incoming Connection
Never accept incoming
Accept with DTR Active
Always Accept
0
0
1
0
1
1
0
0
0
b) Response
Nothing (quiet)
0
1
Character response (C=connect,
D=disconnect, N=unreachable)
c) Active Startup
No active startup
With any character
With DTR Active
With a specific start character
Manual connection
Autostart
0
0
0
0
0
0
0
0
0
0
1
1
0
0
1
1
0
0
0
1
0
1
0
1
Hostlist
0
0
1
0
d) Datagram Type
Directed UDP
e) Modem Mode
No Echo
1
1
0
0
0
0
0
1
1
1
1
1
Data Echo & Modem Response
(Numeric)
1
Data Echo & Modem Response
(Verbose)
0
1
1
1
0
Modem Response Only (Numeric)
Modem Response Only (Verbose)
0
0
0
0
1
1
1
1
1
1
1
0
a) Incoming Connection
Never Accept Incoming
Accept with DTR Active
Rejects all external connection attempts.
Accepts external connection requests only when the DTR input
is asserted. Cannot be used with Modem Mode.
Always Accept
Accepts any incoming connection when a connection is not
already established. Default setting.
UDS1100 User Guide
43
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
b) Response
Character Response
A single character is transmitted to the serial port when there is a
change in connection state:
C = connected, D = disconnected, N = host unreachable.
This option is overridden when the Active Start Modem Mode
or Active Start Host List is in effect. Default setting is Nothing
(quiet).
c) Active Startup
No Active Startup
Does not attempt to initiate a connection under any
circumstance. Default setting.
With Any Character
With DTR Active
Attempts to connect when any character is received from the
serial port.
Attempts to connect when the DTR input changes from not
asserted to asserted.
With a Specific Start
Character
Attempts to connect when it receives a specific start character
from the serial port. The default start character is carriage return.
Manual Connection
Attempts to connect when directed by a command string
received from the serial port. The first character of the command
string must be a C (ASCII 0x43), and the last character must be
either a carriage return (ASCII 0x0D) or a line feed (0x0A). No
blanks or space characters may be in the command string.
Between the first and last command string characters must be a
full or partial destination IP address and may be a destination
port number.
The IP address must be in standard decimal-dot notation and
may be a partial address, representing the least significant 1, 2,
or 3 bytes of the remote IP address. The period is required
between each pair of IP address numbers.
If present, the port number must follow the IP address, must be
presented as a decimal number in the range 1-65535, and must
be preceded by a forward slash (ASCII 0x2F). The slash
separates the IP address and the port number. If you omit the
port number from a command string, the internally stored remote
port number starts a connection.
If a partial IP address is presented in a command string, it is
interpreted to be the least significant bytes of the IP address and
uses the internally stored remote IP address to provide the most
significant bytes of the IP address. If the IP address entered is
0.0.0.0/0, the device server enters Monitor Mode.
For example, if the remote IP address already configured in the
unit is 129.1.2.3, then an example command string would be
C3/7. (This would connect to 129.1.2.3 and port 7.) You may
also use a different ending for the connection string. For
example, C50.1/23 would connect you to 129.1.50.1 and port 23.
UDS1100 User Guide
44
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Figure 7-3. Manual Connection Address Example
Command String
Result if remote IP is 129.1.2.3 and remote port is 1234
Complete override; connection is started with host 121.2.4.5,
port 1.
C121.2.4.5/1
C5
Connects to 129.1.2.5, port 1234.
Connects to 129.1.28.10, port 12.
Enters Monitor Mode.
C28.10/12
C0.0.0.0/0
Autostart (Automatic
Connection)
If you enable Autostart, the unit automatically connects to the
remote IP address and remote port specified when the firmware
starts.
Hostlist
If you enable this option, the device server scrolls through the
hostlist until it connects to a device listed in the hostlist table.
Once it connects, the unit stops trying to connect to any others. If
this connection fails, the unit continues to scroll through the table
until it is able to connect to another IP in the hostlist.
Hostlist supports a minimum of 1 and a maximum of 12 entries.
Each entry contains the IP address and the port number.
The hostlist is disabled for Manual and Modem Modes. The unit
does not accept a data connection from a remote device when
the hostlist option is enabled.
Figure 4-7. Hostlist Option
UDS1100 User Guide
45
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
To enable the hostlist:
1. Enter a Connect Mode of 0x20 (2X), where X is any digit. The menu shows you
a list of current entries already defined in the product.
2. To delete, modify, or add an entry, select Yes. If you enter an IP address of
0.0.0.0, that entry and all others after it are deleted.
3. After completing the hostlist, repeat the previous step if necessary to edit the
hostlist again.
4. For Retrycounter, enter the number of times the Lantronix unit should try to
make a good network connection to a hostlist entry that it has successfully
ARPed. The range is 1-15, with the default set to 3.
5. For Retrytimeout, enter the number of seconds the unit should wait before
failing an attempted connection. The time is stored as units of milliseconds in the
range of 1-65535. The default setting is 250.
d) Datagram Type
Directed UDP
When selecting this option, you are prompted for the Datagram type.
Enter 01 for directed or broadcast UDP.
When the UDP option is in effect, the unit never attempts to initiate a
TCP connection because it uses UDP datagrams to send and receive
data.
e) Modem Mode
In Modem (Emulation) Mode, the unit presents a modem interface to the attached
serial device. It accepts AT-style modem commands and handles the modem signals
correctly.
Normally, there is a modem connected to a local PC and a modem connected to a
remote machine. A user must dial from the local PC to the remote machine,
accumulating phone charges for each connection. Modem Mode allows you to
replace modems with UDS1100s, and to use an Ethernet connection instead of a
phone call. By not having to change communications applications, you avoid
potentially expensive phone calls.
To select Modem Mode, set the Connect Mode to C6 (no echo), D6 (echo with full
verbose), D7 (echo with numeric response), CF (modem responses only, numeric
response), or CE (modem responses only, full verbose).
Note: If the unit is in Modem Mode, and the serial port is idle, the unit can
still accept network TCP connections to the serial port if Connect Mode is set
to C6 (no echo), D6 (echo with full verbose), D7 (echo with numeric
response, CF (modem responses only, numeric response), or CE (modem
responses only, full verbose).
Without Echo
In Modem Mode, echo refers to the echo of all of the characters
entered in command mode; it does not mean to echo data that is
transferred. Quiet Mode (without echo) refers to the modem not
sending an answer to the commands received (or displaying what
was typed).
UDS1100 User Guide
46
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Data Echo & Modem
Response
Full Verbose: The unit echoes modem commands and responds to
a command with a message string shown in the table below.
Numeric Response: The unit echoes modem commands and
responds to a command with a numeric response.
Modem Responses
Only
Full Verbose: The unit does not echo modem commands and
responds to a command with a message string shown in the table
below.
Numeric Response: The unit does not echo modem commands
and responds to a command with a numeric response.
Table 4-11. Modem Mode Messages
Meaning
Message
Full Verbose
OK
Command was executed without error.
A network connection has been established.
A network connection has been closed.
CONNECT
NO CARRIER
A remote device, having IP address n.n.n.n, is connecting to this
device.
RING n.n.n.n.
Numeric Response
0
1
2
3
4
OK
Connected
Ring
No Carrier
Error
Received commands must begin with the two-character sequence AT and be
terminated with a carriage return character.
The unit ignores any character sequence received not starting with AT, and only
recognizes and processes single AT-style commands. The unit treats compound AT
commands as unrecognized commands.
If the Full Verbose option is in effect, the unit responds to an unrecognized
command string that is otherwise formatted correctly (begins with AT and ends with
carriage return) with the "OK" message and takes no further action.
If the Numeric Response option is in effect, the unit responds to an unrecognized
command string that is otherwise formatted correctly with a "0" message and takes
no further action.
When an active connection is in effect, the unit transfers data and does not process
commands received from the serial interface.
When a connection is terminated or lost, the unit reverts to command mode.
UDS1100 User Guide
47
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
When an active connection is in effect, the unit terminates the connection if it
receives the following sequence from the attached serial device:
‹
‹
No serial data is received for one second.
The character sequence +++ is received, with no more than one second
between each two characters.
‹
‹
No serial data is received for one second after the last + character. At this time,
the unit responds affirmatively per the selected echo/response mode.
The character string ATH is received, terminated with a carriage return. The
unit responds affirmatively according to the selected echo/response mode and
drops the network connection. The serial interface reverts to accepting
command strings.
If this sequence is not followed, the unit remains in data transfer mode.
Table 7-6. Modem Mode Commands
Modem Mode
Command
Function
ATDTx.x.x.x,pppp or Makes a connection to an IP address (x.x.x.x) and a remote port
ATDTx.x.x.x/pppp
number (pppp).
Makes a connection to an IP address (x.x.x.x) and the remote port
number defined within the unit.
ATDTx.x.x.x
Forces the unit into Monitor Mode if a remote IP address and port
number are defined within the unit.
ATD0.0.0.0
ATD
Forces the unit into Monitor Mode if a remote IP address and port
number are not defined within the unit.
Makes a connection to an IP address (x.x.x.x) and the remote port
number defined within the unit.
ATDx.x.x.x
ATH
Hangs up the connection (Entered as +++ATH ).
Enables or disables connections from the network going to the serial
port.
n=0 disables the ability to make a connection from the network to the
serial port.
ATS0=n
n=1-9 enables the ability to make a connection from the network to
the serial port.
n>1-9 is invalid.
Enables or disables character echo and responses.
n=0 disables character echo and responses.
n=1 enables character echo and responses.
ATEn
ATVn
Enables numeric response or full verbose.
n=0 enables numeric response.
n=1 enables full verbose.
Note: The unit recognizes these AT commands as single commands such as
ATE0 or ATV1; it does not recognize compound commands such as ATE0V.
UDS1100 User Guide
48
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Send the Escape Sequence (+++) in Modem Mode
Send ‘+++’ in Modem Mode (Y) ? _
Disable or enable the UDS1100’s ability to send the escape sequence. The default
setting is Y (Yes) (send the escape sequence).
Auto Increment Source Port
Auto increment source port (N) ? _
Y (Yes) auto increment the source port. The UDS1100 increments the port number
used with each new connection.
Remote IP Address
This is the destination IP address used with an outgoing connection.
Remote IP Address : (000) (000) (000) (000)_
Note: This option does not display when Hostlist is enabled from the
Remote Port
You must set the remote TCP port number for the unit to make outgoing connections.
This parameter defines the port number on the target host to which a connection is
attempted.
Remote Port (0) ? _
To connect an ASCII terminal to a host using the unit for login purposes, use the
remote port number 23 (Internet standard port number for Telnet services).
Note: This option does not display when Hostlist is enabled from the
DisConnMode
This setting determines the conditions under which the unit will cause a network
connection to terminate. The default setting is 00.
DisConnMode (00) ? _
Notes:
‹
In DisConnMode (Disconnect Mode), DTR drop either drops the connection or
is ignored.
‹
All bit positions in the table that are blank represent “don’t care” bits for that
particular option, which can be set to either a 0 or 1 value.
UDS1100 User Guide
49
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Table 7-7. Disconnect Mode Options
Disconnect Mode Option
7
6
5
4
3
2
1
0
(6)
Disconnect with DTR drop
1
Ignore DTR
0
Telnet mode and terminal type setup (1)
Channel (port) password (2)
Hard disconnect (3)
1
1
0
1
Disable hard disconnect
State LED off with connection (4)
Disconnect with EOT (^D) (5)
1
1
(1) The UDS sends the "Terminal Type" upon an outgoing connection.
(2) A password is required for a connection to the serial port from the network.
(3) The TCP connection closes even if the remote site does not acknowledge the
disconnection.
(4) When there is a network connection to or from the serial port, the state LED turns off
instead of blinking.
(5) When Ctrl+D or Hex 04 is detected, the connection is dropped. Both Telnet Mode
and Disconnect with EOT must be enabled for Disconnect with EOT to function
properly. Ctrl+D is only detected going from the serial port to the network.
(6) When DTR transitions from a high state to a low state, the network connection to or
from the serial port drops.
Flush Mode (Buffer Flushing)
Using this parameter, you can control line handling and network buffers with
connection startup and disconnect. The default setting is 00.
FlushMode (00) ? _
You can also select between two different packing algorithms.
Note: All bit positions in the table that are blank represent “don’t care” bits for
that particular option, which can be set to either a 0 or 1 value.
UDS1100 User Guide
50
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Table 7-8. Flush Mode Options
Function
7
6
5
4
3
2
1
0
Input Buffer (Serial to Network)
Clear with a connection initiated from the device to the network
Clear with a connection initiated from the network to the device
Clear when the network connection to or from the device is disconnected
Output Buffer (Network to Serial)
1
1
1
Clear with a connection initiated from the device to the network
Clear with a connection initiated from the network to the device
Clear when the network connection to or from the device is disconnected
Alternate Packing Algorithm (Pack Control)
1
1
1
Enable
1
Pack Control
The packing algorithms define how and when packets are sent to the network. The
standard algorithm is optimized for applications in which the unit is used in a local
environment, allowing for very small delays for single characters, while keeping the
packet count low. The alternate packing algorithm minimizes the packet count on the
network and is especially useful in applications in a routed Wide Area Network
(WAN). Adjusting parameters in this mode can economize the network data stream.
Pack control settings are enabled in Flush Mode. Set this value to 00 if you do not
need specific functions.
Note: All bit positions in the table that are blank represent “don’t care” bits for
that particular option, which can be set to either a 0 or 1 value.
Table 7-9. Pack Control Options
Option
7
6
5
4
3
2
1
0
Packing Interval
Interval: 12 msec
Interval: 52 msec
Interval: 250 msec
Interval: 5 sec
Trailing Characters
None
0
0
1
1
0
1
0
1
0
0
1
0
1
0
One
Two
UDS1100 User Guide
51
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
Option
7
6
5
4
3
2
1
0
Send Characters
2-Byte Send Character Sequence
Send Immediately After Send chars
1
1
Packing Interval
Packing Interval defines how long the unit should wait before sending accumulated
characters. This wait period is between successive network segments containing
data. For alternate packing, the default interval is 12 ms.
Trailing Characters
In some applications, CRC, Checksum, or other trailing characters follow the end-of-
sequence character; this option helps to adapt frame transmission to the frame
boundary. The default setting is 00 (none).
Send Characters
‹
‹
If 2-Byte Send Character Sequence is enabled, the unit interprets the
sendchars as a 2-byte sequence; if this option is not enabled, the unit
interprets them independently. The default setting is 0 (disabled).
If Send Immediately After Characters is not set, any characters already in
the serial buffer are included in the transmission after a "transmit" condition is
found. If this option is set, the unit sends immediately after recognizing the
transmit condition (sendchar or timeout). The default setting is 0.
Note: A transmission might occur if status information needs to be
exchanged or an acknowledgment needs to be sent.
DisConnTime (Inactivity Timeout)
Use this parameter to set an inactivity timeout. The unit drops the connection if there
is no activity on the serial line before the set time expires. Enter time in the format
mm:ss, where m is the number of minutes and s is the number of seconds.
DisConnTime (00:00) ?:
To disable the inactivity timeout, enter 00:00. Range is 0 (disabled) to 5999 seconds
(99 minutes, 59 seconds). Default setting is 0.
Send Characters
Enter up to two characters in hexadecimal representation in sendchar.
SendChar 1 (00) ? _
SendChar 2 (00) ? _
If the unit receives a character on the serial line that matches one of these
characters, it sends the character immediately, along with any awaiting characters, to
the TCP connection. This action minimizes the response time for specific protocol
characters on the serial line (for example, ETX, EOT). Setting the first sendchar to 00
UDS1100 User Guide
52
Download from Www.Somanuals.com. All Manuals Search And Download.
7: Setup Mode: Channel Configuration
disables the recognition of the characters. Alternatively, the unit can interpret two
Telnet Terminal Type
This parameter displays only if you enabled the terminal type option in Disconnect
Mode. With this option enabled, you can use the terminal name for the Telnet
terminal type. Enter only one name.
With terminal type option enabled, the unit also reacts to the EOR (end of record) and
binary options, useful for applications like terminal emulation to IBM hosts.
Channel (Port) Password
This parameter appears only if the channel (port) password option is enabled in
Disconnect Mode. With this option enabled, you can set a password on the serial
port. The default setting is all 0s.
UDS1100 User Guide
53
Download from Www.Somanuals.com. All Manuals Search And Download.
8: Setup Mode: Advanced Settings
Expert Settings (Option 5)
Note: You can change these settings using Telnet or serial connections only,
not on the Web-Manager.
Caution: Changing the expert settings can drastically affect the
performance and access to the product. These settings should only be
changed by an experienced network administrator.
Figure 8-1. Expert Settings
The default settings are listed below:
TCP Keepalive time in s
(1s – 65s; 0s=disable)
45
ARP Cache timeout in s
(1s – 600s)
600
Disable Monitor Mode @
bootup
Enabled
80
HTTP Port Number
(1-65535)
MTU Size (512 – 1400)
Enable alternate MAC
Ethernet connection type
0 (resulting in an operational value of 1400)
Disabled (OEM use only)
0 (resulting in auto-negotiation)
TCP Keepalive time in seconds
This option allows you to change how many seconds the unit waits during a silent
connection before attempting to see if the currently connected network device is still
on the network. If the unit gets no response, it drops that connection. The default
setting is 45.
TCP Keepalive time in s (1s – 65s; 0s=disable): (45)? _
UDS1100 User Guide
54
Download from Www.Somanuals.com. All Manuals Search And Download.
8: Setup Mode: Advanced Settings
ARP Cache timeout in seconds
Whenever the unit communicates with another device on the network, it adds an
entry into its ARP table. The ARP Cache timeout option allows you to define how
many seconds (1-600) the unit will wait before timing out this table. The default
setting is 600.
ARP Cache timeout in s (1s – 65s; 0s=disable): (600)? _
Disable Monitor Mode at bootup
This option allows you to disable all entries into Monitor Mode during startup, except
for the ‘xxx’ sequence. This prevents entry using yyy, zzz, xx1, and yy1 key
sequences (only during the bootup sequence). The default for Monitor Mode at
Monitor Mode @ bootup : enabled
HTTP Port Number
This option allows the configuration of the web server port number. The valid range is
1-65535. The default HTTP port number is 80.
HTTP Port Number : (80) ? _
MTU Size
The Maximum Transmission Unit (MTU) is the largest physical packet size a network
can transmit for TCP and UDP. Enter between 512 and 1400 bytes. The default
setting is 1400 bytes.
MTU Size: (1400) ? _
Enable alternate MAC
If necessary, enable the alternate MAC address (if specified in the OEM setup
record). The default setting is N (No).
Enable alternate MAC (N) ? _
Ethernet connection type
The UDS1100 allows for the Ethernet speed and duplex to be manually configured.
Enter 0 for auto-negotiation (default). To select the speed and duplex, enter one of
the following: 2 (10Mbit/half duplex), 3 (10Mbit/full duplex), 4 (100Mbit/half duplex), or
5 (100Mbit/full duplex).
Ethernet connection type: (0) ? _
UDS1100 User Guide
55
Download from Www.Somanuals.com. All Manuals Search And Download.
8: Setup Mode: Advanced Settings
Security Settings (Option 6)
You can change security settings by means of Telnet or serial connections only, not
on the Web-Manager. We recommend that you set security over the dedicated
network or over the serial setup to prevent eavesdropping.
Caution: Disabling both Telnet Setup and Port 77FE will prevent users
from accessing the setup menu from the network. Disabling Port 77FE
also disables the Web from configuring the device.
Select 7 to configure security settings.
Figure 8-2. Security Settings
Disable SNMP
This setting allows you to disable the SNMP protocol on the unit for security reasons.
The default setting is N (No).
Disable SNMP (N) ? _
SNMP Community Name
The SNMP Community Name is a required field for NMS to read or write to a device.
Enter a string of 1 to 13 characters. The default setting is public.
SNMP Community Name (public): _
The default entry is public. The current value is displayed in parentheses.
Disable Telnet Setup
Note: If you choose to disable this option, keep in mind that disabling both
Telnet Setup and Port 77FE will prevent users from accessing the setup
menu from the network.
This setting defaults to the N (No) option. The Y (Yes) option disables access to
Setup Mode by Telnet (port 9999). It only allows access locally using the web pages
and the serial port of the unit.
Disable Telnet Setup (N) ? _
UDS1100 User Guide
56
Download from Www.Somanuals.com. All Manuals Search And Download.
8: Setup Mode: Advanced Settings
Disable TFTP Firmware Update
This setting defaults to the N (No) option. The Y (Yes) option disables the use of
TFTP to perform network firmware upgrades. With this option, you can download
firmware upgrades over the serial port using DeviceInstaller’s Recover Firmware
Disable TFTP Firmware Update (N) : _
Disable Port 77FE (Hex)
Note: If you choose to disable this option, keep in mind that disabling both
Telnet Setup and Port 77FE will prevent users from accessing the setup
menu from the network.
Port 77FE is a setting that allows DeviceInstaller, Web-Manager, and custom
programs to configure the unit remotely. You may wish to disable this capability for
security purposes.
Disable Port 77FEh (N) ? _
The default setting is the N (No) option, which enables remote configuration. You can
configure the unit by using DeviceInstaller, web pages, Telnet, or serial configuration.
The Y (Yes) option disables remote configuration and web sites.
Disable Web Server
This setting defaults to the N (No) option. The Y (Yes) option disables the web
server.
Disable Web Server (N) ? _
Disable Web Setup
The Y (Yes) option disables configuration using the Web-Manager. This setting
defaults to the N (No) option.
Disable Web Setup (N) ? _
Disable ECHO Ports
This setting controls whether port 7 echoes characters it receives. The default setting
is Y (Yes), which disables ECHO ports.
Disable ECHO ports (Y) ? _
Enable Enhanced Password
This setting defaults to the N (No) option, which allows you to set a 4-character
password that protects Setup Mode by means of Telnet and web pages. The Y (Yes)
option allows you to set an extended security password of 16-characters for
protecting Telnet and Web Page access.
Enable Enhanced Password (N) ? _
UDS1100 User Guide
57
Download from Www.Somanuals.com. All Manuals Search And Download.
8: Setup Mode: Advanced Settings
Default Settings (Option 7)
Select 7 to reset the unit’s Channel 1 configuration and expert settings to the default
settings. The server configuration settings for IP address, gateway IP address, and
netmask remain unchanged. The configurable pins’ settings also remain unchanged.
The specific settings that this option changes are listed below:
Channel 1 Configuration Defaults
Baudrate
9600
I/F Mode
4C (1 stop bit, no parity, 8 bit, RS-232C)
10001
Own TCP port number
Connect Mode
C0 (always accept incoming connection; no active
connection startup)
Hostlist retry counter
3
Hostlist retry timeout
250 (msec)
0x0D (CR)
0
Start character for serial channel 1
All other parameters
Expert Settings Defaults
TCP Keepalive time in s
45
ARP Cache timeout in s
600
No
80
Disable Monitor Mode @ bootup
HTTP Port Number
(1-65535)
MTU Size (512 – 1400)
Enable alternate MAC
Ethernet Connection Type
1400
No ( for OEM use only)
0 (auto-negotiate)
Security Settings Defaults
Disable SNMP
No
SNMP community name
Disable Telnet setup
public
No
Disable TFTP Firmware Update
Disable Port 77FEh
No
No
Disable Web Server
No
UDS1100 User Guide
58
Download from Www.Somanuals.com. All Manuals Search And Download.
8: Setup Mode: Advanced Settings
Disable Web Setup
No
Disable ECHO ports
Yes
No
Enable Enhanced Password
UDS1100 User Guide
59
Download from Www.Somanuals.com. All Manuals Search And Download.
9: Firmware Upgrades
Obtaining Firmware
You can obtain the most up-to-date firmware and release notes for the unit from the
Reloading Firmware
There are several ways to update the unit's internal operational code (*.ROM): using
DeviceInstaller (the preferred way), using TFTP, or using the serial port. You can also
update the unit's internal Web interface (*.COB) using TFTP or DeviceInstaller.
Here are typical names for those files. Check the Lantronix web site for the latest
versions and release notes.
Table 9-1. Firmware Files
ROM File
COB
uds1100_6101.rom
uds1100_webm_1401.cob
Please refer to the DeviceInstaller online Help for information about reloading
firmware using DeviceInstaller. The other methods are discussed below.
Using TFTP: Graphical User Interface
To download new firmware from a computer:
1. Use a TFTP client to send a binary file to the unit (*.ROM to upgrade the unit's
internal operational code and *.COB to upgrade its internal Web interface).
Note: TFTP requires the .ROM (binary) version of the unit's internal
operational code.
2. In the TFTP server field, enter the IP address of the unit being upgraded.
3. Select Upload operation and Binary format.
4. Enter the full path of the firmware file in the Local file name field.
5. In the Remote file name field, enter the current internal operational code (U3) or
WEB1 to WEB19 for the internal Web interface.
6. Click the Upload Now button to transfer the file to the unit.
UDS1100 User Guide
60
Download from Www.Somanuals.com. All Manuals Search And Download.
9: Firmware Upgrades
Figure 9-1. TFTP Window
After the firmware has been loaded and stored, which takes approximately 8 seconds
to complete, the unit performs a power reset.
Using TFTP: Command Line Interface
To download new firmware from a computer:
1. Enter the following from a TFTP command line interface:
tftp –i <ip address> put <local filename> <destination file name>
The following examples demonstrate the TFTP command sequence to download
the .rom file and the .cob file:
tftp –i 192.168.1.111 put uds1100_6101.rom U3
tftp –i 192.168.1.111 put uds1100_webm_1401.cob WEB4
2. In the Remote file name field, enter the current internal operational code (U3) or
WEB1 to WEB19 for the internal Web interface.
Recovering the Firmware Using the Serial Port and DeviceInstaller
If for some reason the firmware is damaged, you can recover the firmware file by
using DeviceInstaller to download the *.ROM file over the serial port.
To recover firmware:
1. Start DeviceInstaller. If your PC has more than one network adapter, a message
displays. Select an adapter and click OK.
2. From the Tools menu, select Advanced/Recover Firmware. The Serial Port
Firmware Upgrade window displays.
3. For Port on PC, enter the COM port on the PC that is connected to the serial
port of the Lantronix unit.
4. For Device Model, be sure the appropriate device (e.g., UDS1100)
displays.
UDS1100 User Guide
61
Download from Www.Somanuals.com. All Manuals Search And Download.
9: Firmware Upgrades
5. For Firmware File, click the Browse button and go to the location where the
firmware file resides.
Note: Make sure the UDS1100 on which you are recovering firmware is connected to
this selected port on your PC.
6. Click OK to download the file.
7. When prompted, reset the device. Status messages and a progress bar at the
bottom of the screen show the progress of the file transfer. When the file transfer
completes, the message “Successful, Click OK to Close” displays.
8. Click the OK button to complete this procedure.
Note For more information, see Recovering Firmware in the DeviceInstaller
online Help.
UDS1100 User Guide
62
Download from Www.Somanuals.com. All Manuals Search And Download.
10: Monitor Mode
Monitor Mode is a command-line interface used for diagnostic purposes.
There are two ways to enter Monitor Mode: locally using the serial port or remotely
using the network.
Entering Monitor Mode Using the Serial Port
To enter Monitor Mode locally:
1. Follow the same steps used for setting the serial configuration parameters
2. Instead of typing three x keys, however:
a) Type zzz (or xx1) to enter Monitor Mode with network connections.
b) Type yyy (or yy1) to enter Monitor Mode without network connections.
A 0> prompt indicates that you have successfully entered Monitor Mode.
Entering Monitor Mode Using the Network Port
To enter Monitor Mode using a Telnet connection:
1. Establish a Telnet session to the configuration port (9999). The following
message appears:
2. Type M (upper case) immediately.
A 0> prompt indicates that you have successfully entered Monitor Mode.
Monitor Mode Commands
The following commands are available in Monitor Mode. Many commands have an IP
address as an optional parameter (xxx.xxx.xxx.xxx). If you enter the IP address, the
command is applied to another unit with that IP address. If you do not enter the IP
address, the command is executed locally.
Note: All commands must be in capital letters. Responses to some of the
commands are in Intel Hex format.
UDS1100 User Guide
63
Download from Www.Somanuals.com. All Manuals Search And Download.
10: Monitor Mode
Table 10-1. Monitor Mode Commands
Command
Command Name
Function
VS x.x.x.x
Version
Queries software header record (16 bytes) of unit
with IP address x.x.x.x.
GC x.x.x.x
SC x.x.x.x
PI x.x.x.x
Get Configuration
Send Configuration
Ping
Gets configuration of unit with IP address x.x.x.x as
hex records (120 bytes).
Sets configuration of unit with IP address x.x.x.x
from hex records.
Pings unit with IP address x.x.x.x to check device
status.
AT
TT
ARP Table
Shows the unit’s ARP table entries.
TCP Connection
Table
Shows all incoming and outgoing TCP connections.
NC
Network Connection
Shows the unit’s IP configuration.
Resets the unit’s power.
RS
Reset
Quit
QU
Exits diagnostics mode.
G0, G1, ....,Ge, Gf
Get configuration
from memory page
Gets a memory page of configuration information
from the device.
S0, S1,...,Se, Sf
Set configuration to
memory page
Sets a memory page of configuration information
on the device.
GM
SS
Get MAC address
Set Security record
Shows the unit's 6-byte MAC address.
Sets the Security record without the encryption key
and length parameters. The entire record must still
be written, but the encryption-specific bytes do not
need to be provided (they can be null since they
are not overwritten).
Note: Entering any of the commands listed above generates one of the
following command response codes:
Table 7-2. Command Response Codes
Response
Meaning
0>
OK; no error
1>
2>
8>
9>
No answer from remote device
Cannot reach remote device or no answer
Wrong parameter(s)
Invalid command
UDS1100 User Guide
64
Download from Www.Somanuals.com. All Manuals Search And Download.
11: Troubleshooting and Contact Information
This chapter discusses how you can diagnose and fix errors quickly without having to
contact a dealer or Lantronix. It helps to connect a terminal to the serial port while
diagnosing an error to view summary messages that may display. When
troubleshooting, always ensure that the physical connections (power cable, network
cable, and serial cable) are secure.
Note: Some unexplained errors might be caused by duplicate IP addresses on the
network. Make sure that your unit's IP address is unique.
When troubleshooting the following problems, make sure that the UDS1100 is
powered up. Confirm that you are using a good network connection.
LEDs
The UDS has the following LEDs, which help you diagnose problems.
‹
‹
‹
‹
‹
Power LED (green)
Ethernet 10/100 Link (yellow = 10 Mb/green = 100 Mb)
Ethernet Half/Full Duplex Activity (yellow = Half Duplex/green = Full Duplex)
Diagnostic (red)
Status (green)
Simultaneously lit Diagnostic (red) and Status (green) LEDs mean something is
wrong. If the Diagnostic LED is lit or blinking, count the number of times the Status
LED blinks between its pauses. The following table explains the LED functions:
Table 11-1. UDS1100 LEDs
Condition
Diagnostic LED
Channel 1 Status LED
No Errors
OFF
N/A
Network controller error
ON
ON
Blinks 3x/4 seconds
Blinks 4x/4 seconds
Serial number storage
checksum error
Duplicate IP address present
No DHCP response
ON
Blinks 5x/4 seconds
Blinks 5x/4 seconds
Blinks 2x/second
Blinks 2x/second
Setup menu active
Follows Diagnostic LED for 2
seconds, off for 2 seconds
UDS1100 User Guide
65
Download from Www.Somanuals.com. All Manuals Search And Download.
11: Troubleshooting and Contact Information
Problems and Error Messages
Table 11-2. Problems and Error Messages
Problem/Message
Reason
Solution
When you issue the ARP –S
command in Windows, the "ARP
entry addition failed: 5" message
displays.
Your currently logged-in
user does not have the
correct rights to use this
command on this PC.
Have someone from your IT
department log you in with
sufficient rights.
When you attempt to assign an IP
address to the unit by the ARP
method, the "Press Enter to go into
Setup Mode" error "(described
below) message displays. Now
when you Telnet to the device
server, the connection fails.
When you Telnet to port 1
on the device server, you
are only assigning a
temporary IP address.
When you Telnet into port
9999 and do not press
Enter quickly, the device
server reboots, causing it to
lose the IP address.
Telnet back to Port 1. Wait for it to
fail, then Telnet to port 9999 again.
Make sure you press Enter
quickly.
When you Telnet to port 9999, the
You did not press Enter
"Press Enter to go into Setup Mode" quickly enough. You only
Telnet to port 9999 again, but
press Enter as soon as you see
the "Press Enter to go into Setup
message displays. However,
have 5 seconds to press
nothing happens when you press
Enter, or your connection is closed.
Enter before the connection Mode" message.
is closed.
When you Telnet to port 1 to assign
an IP address to the device server,
the Telnet window does not
You may have entered the
Ethernet address incorrectly that you entered with the ARP
with the ARP command.
Confirm that the Ethernet address
command is correct. The Ethernet
address may only include numbers
0-9 and letters A-F. In Windows
and usually in Unix, the segments
of the Ethernet address are
respond for a long time.
separated by dashes. In some
forms of Unix, the Ethernet
address is segmented with colons.
The IP address you are
trying to assign is not on
your logical subnet.
Confirm that your PC has an IP
address and that it is in the same
logical subnet that you are trying to
assign to the device server.
The device server may not
Make sure that the Link LED is lit.
be plugged into the network If the Link LED is not lit, then the
properly.
device server is not properly
plugged into the network.
UDS1100 User Guide
66
Download from Www.Somanuals.com. All Manuals Search And Download.
11: Troubleshooting and Contact Information
Problem/Message
Reason
Solution
When you try to assign an IP with
DeviceInstaller, you get the
following :
The cause is most likely
one of the following:
Double-check the parameters that
you specified.
The hardware address you
specified is incorrect.
Note: You cannot assign an IP
address to a device server through
a router.
"No response from device!
Verify the IP, Hardware
Address and Network Class.
Please try again."
The IP address you are
trying to assign is not a
valid IP for your logical
subnet.
You did not choose the
correct subnet mask.
The device server is not
communicating with the serial
device to which it is attached.
The most likely reason is
the wrong serial settings
were chosen.
The serial settings for the serial
device and the device server must
match. The default serial settings
for the device server are RS-232,
9600 baud, 8 character bits, no
parity, 1 stop bit, no flow control.
When you try to enter the setup
mode on the device server using
the serial port, you get no response. previous problem, or
The issue is most likely
something covered in the
Double-check everything in the
problem above. Confirm that Caps
Lock is not on.
possibly, you have Caps
Lock on.
You can ping the device server, but
not Telnet to the device server on
port 9999.
There may be an IP
address conflict on your
network
Turn the device server off and then
issue the following commands at
the DOS prompt of your computer:
You are not Telneting to
port 9999.
ARP -D X.X.X.X (X.X.X.X is the IP
of the device server).
The Telnet configuration
port (9999) is disabled
within the device server
security settings.
PING X.X.X.X (X.X.X.X is the IP of
the device server).
If you get a response, then there is
a duplicate IP address on the
network. If you do not get a
response, use the serial port to
verify that Telnet is not disabled.
With DeviceInstaller, you get the
Wrong Password error when you try to load is the incorrect
to upgrade the firmware. firmware file for the UDS.
The file you are attempting
Download the correct firmware file
from the Lantronix website.
UDS1100 User Guide
67
Download from Www.Somanuals.com. All Manuals Search And Download.
11: Troubleshooting and Contact Information
Problem/Message
Reason
Solution
The device server appears to be set If you are sure that the
You can check to see whether
there is a socket connection to or
from the UDS by looking at the
Status LED.
up correctly, but you are not
communicating with your device
attached to the device server
across the network.
serial port setting is correct,
then you may not be
connecting to the correct
socket of the device server.
If the Status LED is blinking
consistently, then there is a good
socket connection.
Another possibility is that
the device server is not set
up correctly to make a good
socket connection to the
network.
If the Status LED is solid green,
then the socket connection does
not exist. Use the Connect Mode
option C0 for making a connection
to the UDS from the network. Use
Connect Mode option C1 or C5 for
a connection to the network from
the UDS.
When connecting to the Web-
Manager within the device server,
the "No Connection With The
Device Server" message displays.
Your computer is not able
to connect to port 30718
(77FEh) on the device
server.
Make sure that port 30718 (77FEh)
is not blocked with any router that
you are using on the network. Also,
make sure that port 77FEh is not
disabled within the Security
settings of the device server.
Technical Support
If you are experiencing an error that is not described in this chapter, or if you are
unable to fix the error, you have the following options:
To check our online knowledge base or send a question to Technical Support, go to
Technical Support Europe, Middle East, and Africa
Phone: +33 (0) 1 39 30 41 72
Firmware downloads, FAQs, and the most up-to-date documentation are available at:
When you report a problem, please provide the following information:
‹
‹
‹
‹
‹
Your name, and your company name, address, and phone number
Lantronix model number
Lantronix MAC number
Software version (on the first screen shown when you Telnet to port 9999)
Description of the problem
Status of the unit when the problem occurred (please try to include information on
user and network activity at the time of the problem)
UDS1100 User Guide
68
Download from Www.Somanuals.com. All Manuals Search And Download.
12: Connections and Pinouts
Serial Port
The UDS has a female DCE DB25 serial port that supports RS-232 and RS-485/422
serial standards (software selectable) up to 230 Kbaud.
Figure 12-1. Serial Interface
DB25 Serial Port
Serial Connector Pinouts
The unit’s female DB25 connector provides an RS-232C, RS-485, or RS-422 DCE
serial port. The default serial port settings are 9600 baud, 8 bits, no parity, and 1 stop
bit.
Figure 12-2. DB25 Female DCE Interface RS232
UDS1100 User Guide
69
Download from Www.Somanuals.com. All Manuals Search And Download.
12: Connections and Pinouts
Figure 12-3. DB25 Female Interface RS422 (4 wire mode)
Figure 12-4. DB25 Female Interface RS485 (2 wire mode)
Modem Cable
When attaching the DB25 of the UDS to the DB9 com port on a PC, use a
standard straight-through serial cable (Lantronix Part No. 500-163). The
figure below shows the pinouts for a DB25 to DB9 straight-through cable,
often referred to as a "Modem Cable".
To configure the UDS using the DB9 serial port, you need only pin out the
TXD, RXD, and GND signals.
UDS1100 User Guide
70
Download from Www.Somanuals.com. All Manuals Search And Download.
12: Connections and Pinouts
Figure 12-5. Null Modem Cable (Lantronix Part No. 500-163)
Network Port
The unit's back panel contains a power plug and an RJ45 (10/100) Ethernet port.
Figure 12-6. Network Interface
RJ45 Ethernet Port
Power Plug
UDS1100 User Guide
71
Download from Www.Somanuals.com. All Manuals Search And Download.
12: Connections and Pinouts
Ethernet Connector Pinouts
The UDS1100 supports 10/100 Mbps half or full duplex Ethernet through an RJ45
connector.
Figure 12-7. RJ45 Ethernet Connector
ug
Power Plug
Power input on the power plug is 9 -30 VDC (center +) or 10-24 VAC
(1.5W maximum power required).
UDS1100 User Guide
72
Download from Www.Somanuals.com. All Manuals Search And Download.
13: Technical Specifications
Table 13-1. UDS1100 Technical Specifications
Category
Description
CPU
Lantronix DSTNI-EX 48 MHz clock
256 KB zero wait state SRAM
2 MB Flash
Internal CPU Memory
Flash
EEPROM
2 KB EEPROM
Serial Interface
1 DB25F DCE serial port
Software-selectable baud rate from 300 to 230 KBaud
Software-selectable RS232, RS422 or RS485 (2 and 4 wire support)
Serial Line Formats
Characters: 7 or 8 data bits
Stop bits: 1 or 2
Parity: odd, even, none
Modem Control
Flow Control
DTR, DSR
Hardware: CTS/RTS
Software: XON/XOFF
Power Input
9-30 VDC or 9-24 VAC on barrel connector (1.5 Watts maximum consumption)
9-30 VDC on DB25F serial interface
Network Interface
1 RJ45 10Base-T/100Base-TX Ethernet port
Software selectable Ethernet speed 10/100/Auto
Software selectable Half/Full/Auto duplex
Dimensions
Height: 2.3 cm (0.9 in)
Width: 6.4 cm (2.5 in)
Depth: 9.0 cm (3.5 in)
Weight
0.20 kg (0.45 lb)
Temperature
Operating range: 5° to +50° C (41° to 122° F)
Storage -40° to 66° C (-40 to 151° F)
Relative Humidity
Case
Operating 10% to 90% non-condensing, 40% to 60% recommended
Storage 10% to 90% non-condensing
Metal enclosure with integrated wall mounts
Optional 35 mm Din Rail mount available
Protocols Supported
ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, and HTTP
ModBus TCP, ModBus ASCII/RTU, DF1 Multi-Master (IAP version only)
Installable Industrial
Protocols
Management
Internal web server
SNMP (read only)
Serial login
Telnet login
UDS1100 User Guide
73
Download from Www.Somanuals.com. All Manuals Search And Download.
13: Technical Specifications
Category
System Software
LEDs
Description
DeviceInstaller software
DeviceInstaller, Windows® 95/98/ME/NT/2000/XP-based configuration software
Com Port Redirector, Windows® 98/NT/2000/XP-based virtual com port software
Power
10/100 Mb Link
10/100 Activity
Diagnostic
Status
Emissions
FCC Part 15 Subpart B Class A
Radiated Emissions 30MHz – 1000MHz
Radiated Emissions 30MHz – 1000MHz
Radiated Emissions 30MHz – 1000MHz
ICES-003 Issue 4 February 2004 Class A
AS/NZS CISPR 22: 2004 Class A
EN55022: 1998 + A1: 2000 + A2: 2003 Class A Radiated Emissions 30MHz –
1000MHz
VCCI V-3/2005.04 Class A
EN61000-3-2: 2000 Class A
EN61000-3-3: 1995 + A1: 2001
Radiated Emissions 30MHz – 1000MHz
Harmonic Current Emissions
Fluctuations and Flicker
Immunity
EN55024: 1998 +A1: 2001 +A2: 2003
IEC_61000-4-2: 1995
(Direct/Indirect)
ESD 8KV Air Discharge (Direct), 4KV Contact Discharge
IEC_61000-4-3: 1995
IEC_61000-4-4: 1995
Radiated Immunity 3.0V/m, 1KHz AM Sine Wave at 80%
EFT/Burst 1.0KV Power Lines, 0.5KV I/O Lines
IEC_61000-4-5: 1995
Mode
Surge Immunity 1.0KV Common Mode, 1.0 KV Differential
IEC_61000-4-6: 1996
IEC_61000-4-8: 1993
IEC_61000-4-11: 1994
Conducted Immunity 3.0 Vrms, 80% AM Modulated (1KHz)
Magnetic Field Immunity 50Hz 1.0 Arms/m
Voltage Dips and Interrupts (>95%, 0.5 periods), (30%, 25
periods), (>95%, 250 periods)
Isolation
Designed with protections against transients and ESD for use under harsh
environments
Serial Port: 15 KV ESD protection on RS232 and RS422/485 transceivers
Power Input: Up to non-repeated 600 W 10/100 usec pulse protection against transient
over voltages
Ethernet Port: 1500 VAC isolation shielded with shield connected to chassis ground for
signal integrity and ESD protection
Agency Approvals
UL, CSA, FCC, CE, TUV, CTick, VCCI
UDS1100 User Guide
74
Download from Www.Somanuals.com. All Manuals Search And Download.
A: Alternative Ways to Assign an IP Address
Earlier chapters describe how to assign a static IP address using DeviceInstaller,
Web Manager, and Setup Mode (through a Telnet or serial connection). This section
covers other methods for assigning an IP address over the network.
DHCP
The unit ships with a default IP address of 0.0.0.0, which automatically enables
DHCP. If a DHCP server exists on the network, it provides the unit with an
IP address, gateway address, and subnet mask when the unit boots up.
You can use the DeviceInstaller software to search the network for the DHCP-
assigned IP address and add it to the list of devices retrieved.
Note: This DHCP address does not appear in the unit’s Setup Mode or in
Web Manager. You can determine your unit’s DHCP-assigned IP address in
Monitor Mode. When you enter Monitor Mode from the serial port with
network connection enabled and issue the NC (Network Communication)
command, you see the unit’s IP configuration.
AutoIP
The unit ships with a default IP address of 0.0.0.0, which automatically enables
Auto IP within the unit. AutoIP is an alternative to DHCP that allows hosts to obtain
an IP address automatically in smaller networks that may not have a DHCP server. A
range of IP addresses (from 169.254.0.1 to 169.254.255.1) has been explicitly
reserved for AutoIP-enabled devices. Do not use this range of Auto IP addresses
over the Internet.
‹
If your unit cannot find a DHCP server, and you have not manually assigned an
IP address to it, the unit automatically selects an address from the AutoIP
reserved range. Then, your unit sends out a (ARP) request to other nodes on
the same network to see whether the selected address is being used.
‹
‹
If the selected address is not in use, then the unit uses it for local subnet
communication.
If another device is using the selected IP address, the unit selects another
address from the AutoIP range and reboots. After reboot, the unit sends out
another ARP request to see if the selected address is in use, and so on.
AutoIP does not replace DHCP. The unit continues to look for a DHCP server on the
network. If it finds a DHCP server, the unit switches to the DHCP server-provided
address and reboots.
Note: If a DHCP server is found, but it denies the request for an IP address,
the unit does not attach to the network, but waits and retries.
AutoIP can be disabled by setting the unit’s IP address to 0.0.1.0. This setting
enables DHCP but disables AutoIP.
UDS1100 User Guide
75
Download from Www.Somanuals.com. All Manuals Search And Download.
A: Alternative Ways to Assign an IP Address
BOOTP
Similar to DHCP, but for smaller networks. Automatically assigns the IP address for a
specific duration of time.
ARP and Telnet
If the unit has no IP address, you can use Address Resolution Protocol (ARP)
method from UNIX and Windows-based systems to assign a temporary IP address.
To assign a temporary IP address:
1. On a UNIX or Windows-based host, create an entry in the host's ARP table
using the intended IP address and the hardware address of the unit (on the
product label on the bottom of the unit).
arp -s 191.12.3.77 00:20:4a:xx:xx:xx (Unix)
arp -s 191.12.3.77 00-20-4a-xx-xx-xx (Windows)
Note: For the ARP command to work on Windows 95, the ARP table
on the PC must have at least one IP address defined other than its
own.
2. If you are using Windows 95, type ARP -A at the DOS command prompt to
verify that there is at least one entry in the ARP table. If the local machine is
the only entry, ping another IP address on your network to build a new entry
in the ARP table; the IP address must be a host other than the machine on
which you are working. Once there is at least one additional entry in the ARP
table, use the following command to ARP an IP address to the unit:
arp -s 191.12.3.77 00-20-4a-xx-xx-xx
3. Open a Telnet connection to port 1. The connection fails quickly, but the unit
temporarily changes its IP address to the one designated in this step.
telnet 191.12.3.77 1
4. Open a Telnet connection to port 9999, and press Enter within five seconds
to go into Setup Mode. If you wait longer than five seconds, the unit reboots.
telnet 191.12.3.77 9999
Note: The IP address you just set is temporary and reverts to the default
value when the unit’s power is reset, unless you configure the unit with a
static IP address and store the changes permanently.
UDS1100 User Guide
76
Download from Www.Somanuals.com. All Manuals Search And Download.
B: Binary to Hexadecimal Conversions
Many of the unit’s configuration procedures require assembling a series of options
(represented as bits) into a complete command (represented as a byte). Convert the
resulting binary value to a hexadecimal representation.
Converting Binary to Hexadecimal
Following are two simple ways to convert binary numbers to hexadecimals.
Conversion Table
Hexadecimal digits have values ranging from 0 to F, which are represented as 0-9, A
(for 10), B (for 11), etc. To convert a binary value (for example, 0100 1100) to a
hexadecimal representation, the upper and lower four bits are treated separately,
resulting in a two-digit hexadecimal number (in this case, 4C). Use the following table
to convert values from binary to hexadecimal.
Decimal
Binary Hex
0
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
UDS1100 User Guide
77
Download from Www.Somanuals.com. All Manuals Search And Download.
B: Binary to Hexadecimal Conversions
Scientific Calculator
Another simple way to convert binary to hexadecimals is to use a scientific calculator,
such as the one available on Windows’ operating systems. For example:
1. On the Windows’ Start menu, click ProgramsÆAccessoriesÆCalculator.
2. On the View menu, select Scientific. The scientific calculator displays.
3. Select Bin (Binary), and type the number to convert.
4. Click Hex. The hexadecimal value displays.
UDS1100 User Guide
78
Download from Www.Somanuals.com. All Manuals Search And Download.
C: Warranty
Lantronix warrants each Lantronix product to be free from defects in material and
workmanship for a period of TWO YEARS after the date of shipment. During this
period, if a customer is unable to resolve a product problem and Lantronix Technical
Support determines the product is defective, a Return Material Authorization (RMA)
will be issued. Following receipt of an RMA number, the customer shall return the
product to Lantronix, freight prepaid. Upon verification of warranty, Lantronix will -- at
its option -- repair or replace the product and return it to the customer freight prepaid.
If the product is not under warranty, the customer may have Lantronix repair the unit
on a fee basis or return it. No services are handled at the customer's site under this
warranty. This warranty is voided if the customer uses the product in an unauthorized
or improper way, or in an environment for which it was not designed.
Lantronix warrants the media containing its software product to be free from defects
and warrants that the software will operate substantially according to Lantronix
specifications for a period of 60 DAYS after the date of shipment. The customer will
ship defective media to Lantronix. Lantronix will ship the replacement media to the
customer.
*
*
*
*
In no event will Lantronix be responsible to the user in contract, in tort (including
negligence), strict liability or otherwise for any special, indirect, incidental or
consequential damage or loss of equipment, plant or power system, cost of capital,
loss of profits or revenues, cost of replacement power, additional expenses in the use
of existing software, hardware, equipment or facilities, or claims against the user by
its employees or customers resulting from the use of the information,
recommendations, descriptions and safety notations supplied by Lantronix. Lantronix
liability is limited (at its election) to:
Refund of buyer's purchase price for such affected products (without interest)
Repair or replacement of such products, provided that the buyer follows the
above procedures.
There are no understandings, agreements, representations or warranties, express or
implied, including warranties of merchantability or fitness for a particular purpose,
other than those specifically set out above or by any existing contract between the
parties. Any such contract states the entire obligation of Lantronix. The contents of
this document shall not become part of or modify any prior or existing agreement,
commitment, or relationship.
For details on the Lantronix warranty replacement policy, please go to our Web site
UDS1100 User Guide
79
Download from Www.Somanuals.com. All Manuals Search And Download.
D: Compliance and Disclaimer
Manufacturer’s Name & Address
Lantronix 15353 Barranca Parkway, Irvine, CA 92618 USA
Declares that the following product:
Product Name Model: UDS1100 Device Server
Conforms to the following standards or other normative documents:
Safety
UL 60950-1
CSA 22.2. No 60950-1-03
EN 60950-1
TUV
VCCI
C-TICK
Electromagnetic Emissions
FCC Part 15 Subpart B Class A
ICES-003 Issue 4 February 2004 Class A
AS/NZS CISPR 22: 2004 Class A
EN55022: 1998 + A1: 2000 + A2: 2003 CLASS A
EN61000-3-2: 2000 Class A
EN61000-3-3: 1995 +A1: 2001
VCCI
Electromagnetic Immunity
EN55024: 1998 +A1: 2001 +A2: 2003
IEC 61000-4-2: 1995
IEC 61000-4-3: 1995
IEC 61000-4-4: 1995
IEC 61000-4-5: 1995
IEC 61000-4-6: 1996
IEC 61000-4-8: 1993
IEC 61000-4-11: 1994
UDS1100 User Guide
80
Download from Www.Somanuals.com. All Manuals Search And Download.
D:Compliance and Disclaimer
Disclaimer and Supplementary Information
This product has been designed to comply with the limits for a Class A digital device
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable
protection against such interference when operating in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy, and if not
installed and used in accordance with this guide, may cause harmful interference to
radio communications. Operation of this equipment of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to
correct the interference at user own expense.
This Class A digital apparatus complies with Canadian ICES-003
Cet appareil num′erique de la classe A est conforme ′a la norme NMB-003 du
Canada
The product complies with the requirements of the Low Voltage Directive 72/23/EEC
and the EMC Directive 89/336/EEC.
Changes or modifications to this device not explicitly approved by Lantronix will void
the user's authority to operate this device. The information in this guide may change
without notice. The manufacturer assumes no responsibility for any errors that may
appear in this guide.
Manufacturer’s Contact
Director of Quality Assurance, Lantronix
15353 Barranca Parkway, Irvine, CA 92618 USA
Tel: 949-453-3990
Fax: 949-453-3995
UDS1100 User Guide
81
Download from Www.Somanuals.com. All Manuals Search And Download.
Index
Applications, 9
requirement, 15
ARP and Telnet, 76
AutoIP, 15, 75
searching for on the network, 17
Label, 12
Binary to hexadecimal conversions, 77
BOOTP, 15, 76
LEDs, 65
MAC address, 12
Channel settings, 27, 40
Command line interface, 35
Configuration methods, 11
Connect Mode, 42
Connection settings
TCP, 29
Modem emulation, 11
Modem Mode, 46
Monitor Mode, 63
Netmask, 38
Network settings, 22
Null modem cable, 70
Package contents, 13
Password for Telnet configuration, 38
Pinouts, 69
UDP, 32
Connectors, 69
Contacts, 2
Default settings
Ethernet connector, 72
serial connector, 69
Power plug, 71
applying in Setup Mode, 58
applying in Web-Manager, 34
DeviceInstaller
Problems, 66
accessing the unit, 21
assigning the IP address, 16
installing from product CD, 16
DHCP, 15, 75
Protocols, 11
Redirection software, 10
Required information, 15
RJ45 Ethernet port, 71
RS-232 and RS-485/422 standards, 69
Security settings, 56
Serial port
DHCP name. See
Error messages, 66
Ethernet address, 12
Expert settings, 54
Firmware
accessing Setup Mode, 19
login, 19
recovering, 61
Serial tunneling, 9
Server settings
upgrading, 60
Gateway, 37
Setup Mode, 37
Getting started, 13
Hardware address, 12, 15
Host list settings
Web-Manager, 24
Setup Mode, 35
accessing by serial port connection, 36
accessing by Telnet. See
SNMP, 56
Setup Mode, 45
Web-Manager, 26
Installation, 14
TCP settings, 29
Internal web server, 11
IP address
Technical specifications
Technical Support, 68
TFTP, 60
assigning, 16, 23, 37
automatic assignment, 23
factory default, 15
gateway, 37
Troubleshooting, 7, 65
UDP settings, 32
Warranty, 79
other ways to assign, 75
Web-Manager, 21
UDS1100 User Guide
82
Download from Www.Somanuals.com. All Manuals Search And Download.
UDS1100 User Guide
83
Download from Www.Somanuals.com. All Manuals Search And Download.
|