Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
PURCHASER'S WARRANTY
KW Products Inc. guarantees all parts of its equipment, to the original purchaser, for
one full year from date of recorded warranty (except as provided below) against defects
in material or workmanship when the equipment is installed in strict accordance with
pertinent specifications and procedures.
KW Products Inc. will repair and/or replace free of charge all such defective parts only
when returned to the factory in Marion, with shipping charges prepaid.
This warranty does not cover damage caused by accident, abuse or improper
installation, nor repair or replacement of parts worn or consumed in normal operation of
the machine.
Additionally, this warranty does not cover such items as dresser diamonds, ball
bearings, grinding wheels, belts, carbide tool bits and other accessory items, except at
the discretion of the company. The warranty on electric motors or electrical component
parts is for a period of ninety days from date of delivery.
This warranty is at no time intended to mean the entire machine.
KW Products Inc.
800-553-5953
1.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
RECEIVING SHIPMENT
Upon taking delivery of your machine, carefully inspect the assembly before removing
the crating and packing materials.
If evidence of damage exists, contact the shipper and KW Products Inc. immediately.
Although KW Products Inc. is not responsible for damage incurred during transit, you
will be provided assistance in preparation and filing of any necessary claims.
CAREFULLY READ THIS MANUAL BEFORE ATTEMPTING TO SET-UP OR
OPERATE THIS MACHINE.
Important Note:
Always have your serial number ready when communicating with KW Products Inc.
regarding parts or service.
Keep this manual in a safe place.
DATE RECEIVED:
SERIAL #:
KW Products Inc.
800-553-5953
2.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
SAFETY FIRST
This manual has been prepared for the owner and those responsible for the maintenance of this
machine. It’s purpose aside from proper maintenance and operations, is to promote safety
through the use of accepted practice.
READ THE SAFETY AND OPERATING
INSTRUCTIONS THOROUGHLY BEFORE OPERATING THE MACHINE.
In order to obtain maximum life and efficiency from your machine, follow all the instructions in
the operating manuals carefully.
The specifications put forth in this manual were in effect at the time of publication. However,
owing to KW Products’ policy of continuous improvement, changes to these specifications may
be made at any time without obligation.
KW Products Inc.
800-553-5953
3.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
SAFETY INSTRUCTIONS
1. Read, understand and follow the safety and operating instructions found in this manual. Know
the limitations and hazards associated with operating the machine.
2. Eye Safety: Wear an approved safety face shield, goggles or safety glasses to protect eyes
when operating the machine.
3. Grounding the Machine: Machines equipped with three prong grounding plugs are so equipped
for your protection against shock hazards and should be plugged directly into a properly
grounded three-prong receptacle in accordance with national electrical codes and local codes
and ordinances. A grounding adapter may be used. If one is used, the green lead should be
securely connected to a suitable electrical ground such as a ground wire system. Do not cut off
the grounding prong or use an adapter with the grounding prong removed.
4. Work Area: Keep the floor around the machine clean and free of tools, tooling, stock scrap and
other foreign material and oil, grease or coolant to minimize the danger of tripping or slipping.
Kwik-Way recommends the use of anti-skid floor strips on the floor area where the operator
normally stands and that each machine's work area be marked off. Make certain the work area
is well lighted and ventilated. Provide for adequate workspace around the machine.
5. Guards: Keep all machine guards in place at all times when machine is in use.
6. Do Not Overreach: Maintain a balanced stance and keep your body under control at all times.
7. Hand Safety: NEVER wear gloves while operating this machine.
8. Machine Capacity: Do not attempt to use the machine beyond its stated capacity or operations.
This type of use will reduce the productive life of the machine and could cause the breakage of
parts, which could result in personal injury.
9. Avoid Accidental Starting: Make certain the main switch is in the OFF position before connecting
power to the machine.
10. Careless Acts: Give the work you are doing your undivided attention. Looking around, carrying
on a conversation and horseplay are careless acts that can result in serious injury.
11. Job Completion: If the operation is complete, the machine should be emptied and the work area
cleaned.
12. Disconnect All Power and Air to Machine before performing any service or maintenance.
13. Replacement Parts: Use only Kwik-Way replacement parts and accessories; otherwise,
warranty will be null and void.
14. Misuse: Do not use the machine for other than its intended use. If used for other purposes, KW
Products Inc. disclaims any real or implied warranty and holds itself harmless for any injury or
loss that may result from such use.
KW Products Inc.
800-553-5953
4.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
SAFETY GUIDE FOR SEAT GRINDER WHEELS
(Read before installing the Wheel)
Importance of Proper Machine Maintenance
The most common cause of wheel breakage is due to improper mounting and abusive and/or
careless operation. Only through proper use, regular machine maintenance, service and
inspection procedures can wheel breakage be prevented.
It is the responsibility of the user to inspect, at regular intervals, to be certain that mounting
flanges are in usable condition, are of proper size and shape and that no damage has occurred
to the wheel or the machine.
The following DO'S and DONT'S should be used as a guide to safer grinding
DO
DON'T
1) CHECK all wheels for CRACKS or other
1) DON'T USE wheels WHICH HAVE BEEN
DROPPED or otherwise damaged.
2) DON'T USE EXCESSIVE PRESSURE
WHEN MOUNTING wheel. Tighten nut only
enough to hold wheel firmly.
DAMAGE before mounting.
2) USE MOUNTING BLOTTERS when
supplied with wheels
3) Be sure WHEEL HOLE, threaded or
unthreaded, FITS machine arbor
PROPERLY and that flanges are clean, flat
and of the proper type for the wheel you
are mounting.
3) DON'T USE HEAVY GRINDING
PRESSURE
4) Always RUN WHEEL WITH GUARD IN
PLACE at least one minute before grinding
(wheel dresser).
4) DON'T USE MACHINE FOR ANY
PURPOSE OTHER THAN GRINDING
VALVE SEATS.
5) Always WEAR PROTECTIVE SAFETY
GLASSES or proper face shield.
6) Wear a DUST RESPIRATOR, as dust
conditions are present in most grinding
operations
WARNING:
IMPROPER USE MAY CAUSE BREAKAGE AND SERIOUS INJURY
KW Products Inc.
800-553-5953
5.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
WHEEL DRESSER SET-UP
1. Loosen handle #3 and rotate the pointer line until it aligns to the index angle desired and
retighten.
2. After attaching the correct grinding wheel to the grinder unit, carefully lower the grinder unit
onto the dresser arbor item #1
3. Loosen item #5 and raise or lower the arbor until the face of the wheel is in relative position
to the diamond (#6). Retighten # 5
4. Adjust the diamond #6 by turning the knurled knob #2 until the diamond is nearly in contact
to the face of the grinding wheel.
5. Start the motor and begin dressing the wheel using handle #4 and slowly sweeping the face.
(Follow the directions below)
6. Slowly feed the diamond in while moving it across the face of the grinding wheel while
moving it with handle #4.
WARNING: Take the lightest cut possible – never jam the diamond into the grinding wheel.
KW Products Inc.
800-553-5953
6.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
DRESSING OR TRUING THE VALVE SEAT WHEEL
It is necessary to true or dress seat wheels that have become dull or loaded, or have lost their
form (angle). To obtain the best possible dress, observe the following.
1. Feed the diamond into the wheel very slowly until the diamond just touches the wheel.
2. Move the diamond across the face of the wheel beginning from the bottom and sweep up.
A slow sweep will provide a smoother finish while a rapid sweep will provide a coarse finish.
NOTE: How the wheel is dressed will directly influence the finish of the valve seat. Take care
when dressing the seat wheels, this will improve valve seat finish and increase diamond life.
Check the dress of the wheel frequently during the seat grinding operation. It is better to dress
frequently and remove a slight amount of wheel than to wait too long and have a necessity to
remove an excessive amount to correct the wheel
Changing a valve seat stone angle is only advised if it is to increase the stone angle, i.e., taking
a 15-degree angle wheel and making it a 30-degree.
It is not cost effective to attempt to reduce an angle, too much abrasive and diamond is required
to perform this operation.
KW Products Inc.
800-553-5953
7.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
WHEEL TIGHTENING
In case the grinding wheel should stick on the grinder unit, take the wooden blocks from the box
and use them as shown below. In doing this, be sure to place the blocks up close to the wheel
(within 1/8”) so the pressure will be taken by the bearing area of the unit rather than by the thin
wall in the center. This will avoid any possible damage to the unit.
After gripping the unit tightly, you should be able to unscrew the wheel with the hand. If this
cannot be done, the strap-type wrench furnished will loosen the wheel.
CAUTION: Never grip either the grinding unit or grinding wheel directly in a vise. The body of
the grinding unit could easily be damaged by doing so or the wheel very likely broken.
KW Products Inc.
800-553-5953
8.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
SEAT GRINDING
In preparation for grinding valve seats the following should be observed:
1. Select the correct arbor for the valve guide. The correct arbor should extend approximately
2 3/4" above the valve seat.
2. Pass the stem end of the arbor through an oily shop towel. DO NOT squirt oil into the valve
guide.
3. Insert the arbor into the valve guide. Care should taken to insure the valve guide is clean
and in good repair.
NOTE: Worn guides will not allow correct reseating of the valve.
4. Select the correct size wheel and angle to grind the valve seat angle. The wheel should be
trued prior to attempting to service the seat. Always true the wheel to the manufacturers
recommended angle for the valve seat to be serviced. (See dressing the wheel)
Helpful Hint: Place a piece of fine sandpaper between the face of the grinding wheel and the
seat (Abrasive facing the valve seat). Turn the stone holder by hand, this will remove any
excess carbon and place it into the sandpaper and not into the wheel. This increases the life of
the wheel by reducing excess dressing to remove carbon from the face of the wheel.
5. Hold the grinding motor up and support its weight, do not push down with the motor during
the grinding operation. Try to maintain as high a RPM as possible while grinding. Run the
stone for approximately 45 seconds then stop and evaluate the seat.
EVALUATION: Seat run-out and surface finish is very critical. Seat width should be to
manufacturer specification and runout generally MUST be below .002 for seats over 1.50" in
diameter and .0015 for seats smaller in diameter than 1.50".
6. Top angle and throat angle should be ground only when necessary to obtain the correct
location of valve seat to valve face. It is also used to narrow a seat angle that is too wide.
KW Products Inc.
800-553-5953
9.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
VALVE PRINTS
The above illustrations provide guidelines to correct seat width and location. Seat width should
be to manufacturer specifications and seat run-out should be as close to 0 as possible.
Maximum not to exceed .002 on 1.5” seats or larger and .0015 on seats below 1.5”
KW Products Inc.
800-553-5953
10.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
MAINTENANCE
Your Kwik-Way SGF Seat Grinder is designed to require minimal maintenance. However, some
basic maintenance assures the unit will continue to operate in a satisfactory manner.
1. The motor features permanently sealed bearings that require no routine oiling.
2. The gears located in the nose housing may require lubrication on a yearly basis. (depending
on use) We recommend the following:
a. Remove the four cap screws and two pan head screws holding the nose to the motor
housing.
b. Keep the motor armature in place by holding against the fan with a screwdriver (prevents
armature from slipping out of the brushes) and remove the nose housing.
c. Once removed, add approximately one teaspoon of grease to the gear cavity of the
housing.
CAUTION: Do not overfill, excess grease will cause the gears to run hot.
3. Brushes should be removed and inspected for wear every 3 months or sooner depending on
use, replace them as required.
KW Products Inc.
800-553-5953
11.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
HELPFUL HINTS
A. PRELIMINARY
1. Be sure to remove the carbon from the valve seats, the ports, and be sure to clean the
valve stem guides.
2. It is good practice to pass the stem of the arbor through an oily cloth both before
and after use. DO NOT SQUIRT OIL IN THE VALVE GUIDE.
3. Care should be taken on some aluminum heads. Forcing the arbor to a very tight fit may
distort the guide. Valve seats ground under these conditions may not end up being
concentric. (Check seats for looseness).
4. Use an arbor that will extend approximately 2-3/4" above the valve seat when properly
set in the guide. Using an arbor that does not extend above the valve seat is likely to
allow the inner key of the grinder unit to continually disengage and engage. This will
break the key and cause premature wear in the sleeve of the guide unit as well as cause
considerable difficulty in grinding accurate valve seats.
B. DRESSING THE WHEEL
1. Feed the diamond to the wheel to take a very light cut; then move it across the wheel
face until the wheel is entirely trued up. (Never jam the diamond into the wheel nor the
wheel against the diamond).
2. Dress the wheel only after the wheel face becomes "worn" or "loaded" by
contact with the seat.
C. GRINDING (USE A TAPPING MOTION WHEN GRINDING TO KEEP THE WHEEL
CLEAN)
1. Before starting the motor, LOWER THE UNIT CAREFULLY ON THE ARBOR UNTIL
THE WHEEL ALMOST CONTACTS THE SEAT.
2. The motor should be held directly in line with the grinder unit, so as to exert a minimum
of side pressure against the arbor.
D. TIGHT WHEEL
1. If the grinder wheel should stick on the grinder unit, it can usually be removed by
gripping the body with the wood block provided, clamped lightly in a vise and unscrewing
the wheel by hand. If stuck too tightly to be unscrewed by hand, it can always be
loosened by using the strap-type wrench furnished.
2. CAUTION: Never grip either the grinding unit or grinding wheel directly in a vise. The
body of the grinding unit: could easily be distorted by doing so or the wheel very likely
broken.
KW Products Inc.
800-553-5953
12.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
STRAIGHT DRIVE ASSEMBLY
REF# PART #
DESCRIPTION
REQ’D
1
2
3
4
5
6
7
8
000-0342-74
6-32 x 5/16 Round Head Machine Screw – N.S.
Tolerance Ring
Loading Spring
2
1
1
3
1
4
4
1
1
1
1
1
1
1
1
1
1
1
000-1400-23
000-1820-44
000-1605-39
000-7300-25
000-0245-89
000-1180-36
000-0566-26
000-0590-21
031-3005-09
031-3006-06
001-0150-44
031-3008-00
031-3009-32
031-3011-30
031-3014-08
031-3019-04
000-0590-56
Bearing
#2 Woodruff Key – N.S.
10-24 x 1 Fillister Head Machine Screw
3/16 Split Lockwasher – Medium Z.P.
5/16-24 x 5/16 Cone Point Socket Set Screw
Tool Bit Screw
Drive Housing
Bearing Retainer
Type H Locktite (.01 ox.) – N.S.
Pinion Nut
Drive Pinion
9
10
11
12
13
14
15
16
17
18
Driven Gear
Bearing Spacer
Drive Coupling
5/16-18 x 3/8 SS – Special
KW Products Inc.
800-553-5953
13.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
MOTOR HOUSING ASSEMBLY
KW Products Inc.
800-553-5953
14.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
MOTOR ASSEMBLY
REF#.
PART #
DESCRIPTION
115V
9,500
RPM
1
115V
11,500
RPM
1
230V
9,500
RPM
230V
11,500
RPM
1
1
2
2
2
2
3
3
3
3
4
5
6
000-1261-01
000-1261-28
000-1412-59
000-1412-70
000-1412-67
000-1412-30
000-1412-08
000-1412-20
000-1412-16
000-1412-25
000-0202-65
000-0245-97
000-0361-45
16-3 SJO Cord Set (8'-6") (115V
16-3 SJO Cord Set (8'-6") (230V)
Rotor (With Shaft)
Rotor (With Shaft)
Rotor (With Shaft)
Rotor (With Shaft)
Stator Assembly
Stator Assembly
Stator Assembly
1
1
1
1
1
1
1
1
1
Stator Assembly
1
2
2
1
6-32 X 1/4 Round Head Machine Screw
10-24 X 2-1/2 Fil. Head Machine Screw
6-32 X 3/16 Pan Head Brass Machine
Screw
2
2
1
2
2
1
2
2
1
7
8
9
000-0482-67
000-1170-13
000-1180-01
000-1201-20
000-1247-02
000-1400-15
000-1425-06
000-1604-82
000-1820-79
000-2005-49
000-2800-38
000-6602-30
000-6602-28
000-6602-27
000-6602-29
000-7300-25
003-0062-04
003-0072-43
031-0198-42
031-3001-52
031-3001-50
031-3001-53
031-3001-51
031-3000-10
031-3000-15
031-3000-29
031-3000-35
10-24 X 3/16 C. P. Socket Set Screw
External Locking Washer
#10 Split Lock Washer-Med. Z.P. N.S
C-H Switch
Eye Terminal
Tolerance Ring
Brush Holder Cap
Bearing
Loading Spring
21/32 I.D. X 1-1/8 O.D. X .010 Fish Paper
Insulator Bushing
Nameplate
Nameplate
Nameplate
Nameplate
#2 Woodruff Key
Brush Holder
Motor Brush
Cord Protector
Housing Assembly
Housing Assembly
Housing Assembly
Housing Assembly
SGF Motor Assembly, Complete – N.S.
SGF Motor Assembly, Complete – N.S.
SGF Motor Assembly, Complete – N.S.
SGF Motor Assembly, Complete – N.S.
2
1
2
1
1
1
2
1
1
2
1
1
2
1
2
1
1
1
2
1
1
2
1
2
1
2
1
1
1
2
1
1
2
1
2
1
2
1
1
1
2
1
1
2
1
10
11
12
13
14
15
16
17
18
18
18
18
19
20
21
22
23*
23*
23*
23*
24**
24**
24**
24**
1
1
1
1
2
2
1
1
2
2
1
1
1
2
2
1
1
2
2
1
1
1
1
1
1
1
1
*
Includes Motor Housing, Handle Plate & Screws Only
** Includes Motor Assembly & Angle Drive Assembly
N.S. = Not Shown
KW Products Inc.
800-553-5953
15.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
FLEX GRINDER UNIT WITHOUT STABILIZER
REF#
1
2
3
4
5
6
7
8
PART #
DESCRIPTION
Inner Sleeve Key
Spring Retainer
Garter Spring
Inner Bearing Spacer
Ball Bearing Sleeve
Grinder Body Cap Assembly
Seat Grinder Body
Flex Coupling (Steel)
Coupling Sleeve
REQ’D
031-0317-53
031-0315-83
031-0315-16
031-0315-08
031-0312-22
031-0302-77
031-0301-02
031-0304-10
031-0124-22
031-0121-39
004-0018-34
031-1005-42
031-1005-34
031-1005-26
031-1005-18
000-1602-10
000-1135-06
000-0402-90
000-1600-83
031-0125-70
031-1121-09
1
1
1
1
1
1
1
1
9
1
1
1
10
11
12
13
14
15
16
17
18
19
20
21
Motor Coupling Shank
Plastic Closure
.010 Thick Steel Shim
.005 Thick Steel Shim
.003 Thick Steel Shim
.002 Thick Steel Shim
Bearing
Bearing Locknut
10-32 UNF x 1/8 Long Cup Point Socket Set Screw
Bearing
As Req’d
As Req’d
As Req’d
As Req’d
1
1
2
1
1
1
Coupling (HOSE)
Coupling Screw
KW Products Inc.
800-553-5953
16.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
ARBOR PULLER ASSEMBLY – 7/16 & 13/32
REF #
PART #
DESCRIPTION
REQ’D
1
2
3
4
5
6
7
000-0485-18
000-1802-46
000-7204-70
049-0401-05
049-0402-02
049-0403-00
049-0405-04
1/4-20 x 1/4 Socket Cup Point Set Screw
Compression Spring
1/8 x 5/8 Roll Pin
Arbor Pulley Body
Pilot Pullout Pin
1
1
2
1
1
2
2
Puller Arm
Puller Pin
KW Products Inc.
800-553-5953
17.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
ECCENTRIMETER ASSEMBLY
REF #
PART #
DESCRIPTION
REQ’D
1
2
3
4
5
6
7
8
000-0400-10
049-0145-20
000-0760-40
049-0342-61
000-0205-75
049-0341-21
049-0143-84
049-0143-25
001-0036-15
000-1180-36
8-32 X 1/8 Headless Set Screw
Finger Nut
Thumb Screw
3
1
1
1
1
1
1
1
1
1
Finger Holder
10-32 x 1/4 Round Head Machine Screw Z.P
Eccentrimeter Body (7/16)
Short Finger- 1"
Long Finger - 1 1/2"
Indicator
9
10
3/16 Lock washer – Medium – Z.P.
NOTE: Either length finger is available.
KW Products Inc.
800-553-5953
18.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
BRAKE ASSEMBLY
REF #
PART #
DESCRIPTION
REQ’D
1
2
3
4
031-3017-00
031-0189-35
031-3018-07
031-0190-36
End Cap Sleeve
Inner Brake Ring
Outer Brake Collar
Brake Pin
1
1
1
2
KW Products Inc.
800-553-5953
19.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
HEAVY DUTY WHEEL DRESSER ASSEMBLY (031-1900-02)
NOTE: Part numbers marked (*) are part of Item #17 and are listed for service only.
KW Products Inc.
800-553-5953
20.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
HEAVY DUTY WHEEL DRESSER ASSEMBLY
R£FNO.
1
2
3
4
5
6
7
8
PART #
DESCRIPTION
Base
REQ'D
031-1901-00
031-1916-10
000-0485-18
031-1908-00
000-1070-18
004-0015-40
031-1909-83
000-4500-22
000-0228-02
000-1047-60
031-1905-09
031-0204-41
031-1903-80
031-1922-00
031-1921-02
031-1906-06
031-1912-03
000-6601-40
031-1912-54
031-1910-09
000-0225-35
031-1911-06
065-0315-07
000-1800-92
031-1917-00
031-1920-05
000-0487-63
031-1919-04
000-1600-67
031-1913-00
000-1850-78
000-1803-86
031-1917-85
000-0100-14
000-7203-72
031-0202-80
1
1
1
1
1
1
1
3
2
1
3
3
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
Diamond Holder Assembly
1/4-20 x 1/4 Cup Point Socket Set Screw
Diamond Swivel Plate
1/2-20 Hex Finish Jam Nut
Handle
Wheel Guard - 4"
5/16-18 Ball
1/4-20 x 3/4 Flat Head Machine Screw
1/4-13 Hex Finish Jam Nut
Lock screw Handle
Lock screw Head
Arbor Lock screw
Lock screw Collar
Swivel Plate Lock screw
Pivot Pin
Diamond Carrier Arm Assembly (Includes Items *)
Nameplate
Diamond Carrier Shaft
Carrier Clamping Plate
10-24 x 1/2 Flat Head Machine Screw
Swivel Plate Key
Spring Tension Screw
Compression Spring (Not Shown)
Plug (Not Shown)
Carrier Stop Pin
5/16-18 x 5/16 Cup Point Socket Set Screw
Carrier Stop Collar
Bearing
Spacer
Torsion Spring
Compression Spring
End Washer
1/4-20 x 1/2 Hex Head Cap Screw
1/8 x 3/8 Roll Pin
Wheel Truing Arbor 7/16 Top – N.S.
9
10
11
12
13
14
15
16
17
18
19*
20
21
22
23*
24*
25*
26*
27*
28*
29*
30*
31*
32*
33*
34*
35*
36
*NOTE: Parts Marked (*) are Part of Item 17 and are listed for service
KW Products Inc.
800-553-5953
21.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
STABILIZER ASSEMBLY
REF #
1
2
PART #
031-0126-78
031-0127-67
DESCRIPTION
Stabilizer
Stabilizer Bushing
REQ’D
1
1
KW Products Inc.
800-553-5953
22.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
SGF SEAT GRINDER
TROUBLE SHOOTING
CONDITIONS
POSSIBLE CAUSES
Rough finish on grinding wheel
Truing cut too heavy or travel of diamond too quick
Damaged diamond
Frequent redressing of grinding wheel necessary
Carbon residue on valve seats
Wrong type grinder wheel for valve seat material
Valve seat finish (rough or chatter) and/or vibration Rough finish on grinder wheel
Loose arbor in guide
Not using Kwik-Way grinder wheels
Worn inner sleeve of grinder body
Worn arbor
Worn bearings in grinder unit
Valve seat not concentric
Worn arbor
Loose arbor in guide
Side pressure
Bent arbor
KW Products Inc.
800-553-5953
23.
500 57th Street, Marion, IA 52302 USA
Copyright 2004 All Rights Reserved
Equipment specifications, options and accessories subject to change without
Download from Www.Somanuals.com. All Manuals Search And Download.
KW Products Inc.
500 57th St., Marion, IA 52302 USA
319/377-9421
319/377-9101 (FAX)
800/553-5953
Download from Www.Somanuals.com. All Manuals Search And Download.
|