RETURN TO MAIN MENU
IM481-B
February, 2011
CV 500-I
For use with machines Codes 10088 thru 10092, 10277, 10278, 11356
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However,
your overall safety can be
increased by proper installation
... and thoughtful operation on
your part. DO NOT INSTALL,
OPERATE OR REPAIR THIS
EQUIPMENT WITHOUT READ-
ING THIS MANUAL AND THE
SAFETY PRECAUTIONS CON-
TAINED THROUGHOUT. And,
most importantly, think before
you act and be careful.
OPERATOR’S MANUAL
Copyright © Lincoln Global Inc.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEBꢀSITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
ii
ii
SAFETY
ARC RAYS can burn.
ELECTRIC SHOCK can
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
fumes and gases. When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
• AC Welder with Reduced Voltage Control.
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and within applicable OSHA PEL and
ACGIH TLV limits using local exhaust or mechanical
ventilation. In confined spaces or in some circum-
stances, outdoors, a respirator may be required.
Additional precautions are also required when welding
on galvanized steel.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f. Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
5. b. The operation of welding fume control equipment is affected
by various factors including proper use and positioning of
the equipment, maintenance of the equipment and the spe-
cific welding procedure and application involved. Worker
exposure level should be checked upon installation and
periodically thereafter to be certain it is within applicable
OSHA PEL and ACGIH TLV limits.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
5.c. Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
5.d. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.e. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.f. Also see item 1.b.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
iii
iii
SAFETY
WELDING and CUTTING
CYLINDER may explode
if damaged.
SPARKS can
cause fire or explosion.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
process used and properly operating
regulators designed for the gas and
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
7.c. Cylinders should be located:
•Away from areas where they may be struck or subjected to
physical damage.
•A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f. Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir-
cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
6.h. Also see item 1.c.
6.I. Read and follow NFPA 51B “ Standard for Fire Prevention
During Welding, Cutting and Other Hot Work”, available
from NFPA, 1 Batterymarch Park, PO box 9101, Quincy, Ma
022690-9101.
6.j. Do not use a welding power source for pipe thawing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
iv
iv
SAFETY
PRÉCAUTIONS DE SÛRETÉ
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
Sûreté Pour Soudage A L’Arc
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
-5-
Download from Www.Somanuals.com. All Manuals Search And Download.
for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
Thank You
CUSTOMER ASSISTANCE POLICY
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equip-
ment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln
Electric for advice or information about their use of our products. We respond to our customers based on the best information in our posses-
sion at that time. Lincoln Electric is not in a position to warrant or guarantee such advice, and assumes no liability, with respect to such infor-
mation or advice. We expressly disclaim any warranty of any kind, including any warranty of fitness for any customer’s particular purpose,
with respect to such information or advice. As a matter of practical consideration, we also cannot assume any responsibility for updating or
correcting any such information or advice once it has been given, nor does the provision of information or advice create, expand or alter any
warranty with respect to the sale of our products.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control
of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in
applying these types of fabrication methods and service requirements.
for any updated information.
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
• For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
• For On-Line Registration: Go to our WEB SITE at www.lincolnelectric.com. Choose “Quick Links” and then
“Product Registration”. Please complete the form and submit your registration.
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or loss of life.
CAUTION
This statement appears where the information must be followed to avoid minor personal injury or damage to this equipment.
-6-
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Page
Safety Precautions .............................................................................................................2-5
Introductory Information.......................................................................................................7
Meaning of Graphic Symbols ............................................................................................8-11
General Machine Description..............................................................................................12
Recommended Processes & Equipment ............................................................................12
Design Summary ................................................................................................................12
Operational Features & Controls ...............................................................................12-14
Technical Specifications .....................................................................................................15
Installation ........................................................................................................................16-18
Safety Precautions .......................................................................................................16
Location........................................................................................................................16
Application Limitations..................................................................................................16
Stacking........................................................................................................................16
Input Power Connections .............................................................................................16
Output Cable Connections ...........................................................................................17
Installation of Field Installed Options .........................................................................17-18
Installation of Equipment Required for Recommended Processes ..............................18
Operating Instructions.........................................................................................................19
Safety Precautions .......................................................................................................19
Power Source Operation..................................................................................................19-21
Duty Cycle ....................................................................................................................19
Starting the Machine.....................................................................................................19
Control Settings & Descriptions........................................................................................19-21
Maintenance .......................................................................................................................21
Routine Maintenance....................................................................................................21
Troubleshooting................................................................................................................22-25
Procedure for Replacing P.C. Boards.................................................................................26
Remote Control & System Checks .....................................................................................27
Twist Mate Welding Cable Plug Instructions.......................................................................28
Diagrams..........................................................................................................................29-30
Parts Pages.................................................................................................................P236 Series
-7-
Download from Www.Somanuals.com. All Manuals Search And Download.
MEANINGS OF GRAPHIC SYMBOLS
The CV 500-I nameplate has been designed to use international symbols in describing the function of the various
components. Below are the symbols used.
POWER ON-OFF SWITCH
Input (Power)
On
Off
OUTPUT CONTROL DIAL
Output Voltage Control (Export Model)
V
Output Voltage Control (European Model)
U
Increase / Decrease of Output Voltage
OUTPUT CONTROL “LOCAL-REMOTE” SWITCH
Remote Output Voltage Control
Local Output Voltage Control
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
CIRCUIT BREAKER
Circuit Breaker
THERMAL PROTECTION LIGHT
High Temperature
VOLTMETER SWITCH
Voltmeter
Positive Electrode
Negative Electrode
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
RATING PLATE
Designates welder complies with National Electrical Manufacturers
Association requirements EW 1. (Export Model only)
NEMAꢀEWꢀ1
Designates welder complies with International Electrotechnical
commission requirements 974-1. (European model only)
IECꢀ974-1
Three Phase Power
Transformer
Rectifier
Rectified DC Output
Constant Voltage Characteristic
Line Connection
Shielded Metal Arc Welding
Flux Cored Arc Welding
Designates Welder can be used in environments with
increased hazard of electric shock. (European model only)
S
Degree of protection provided by the enclosure
IP21
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING IDENTIFICATION
Warning Identification
EARTH GROUND CONNECTION
Signifying the Earth (Ground) Connection
CHASSIS GROUND CONNECTION
Signifying the Chassis (Ground) Connection
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
MACHINE OUTPUT CONTROL SWITCH “LOCAL”
OR “REMOTE”
GENERAL MACHINE DESCRIPTION
The CV 500-I is an SCR controlled three phase DC
power source. It is designed with a single range
potentiometer control.
The machine output voltage can be controlled by
either the “OUTPUT CONTROL” on the machine con-
trol panel, the output control on the wire feed unit, or
an optional “remote control” that is available. This
switch selects the mode of control, either “LOCAL” or
“REMOTE”.
The CV500-I has two models - an Export model and a
European model. The Export model complies with
NEMA EW 1 requirements and the European model
complies with IEC 974-1 requirements.
POLARITY SELECTION
Polarity selection is made by appropriately connecting
the electrode and work welding cables to either the
“+” stud or to the “-” stud. Select “VOLTMETER”
RECOMMENDED PROCESSES
& EQUIPMENT
switch for “+” or “-” electrode, for the remote (#21)
work sensing lead.
The CV 500-I is supplied as a constant voltage power
,
source only. It is designed for all Innershield®
Outershield® and all solid wire and gas procedures
within the capacity of the machine. The output char-
acteristics have been optimized for these CV process-
es without use of a variable arc control.
VOLTMETER SWITCH “+” ELECTRODE OR “-”
ELECTRODE
This switch selects electrode polarity for the remote
(#21) work sensing lead of automatic or semiautomat-
ic equipment.
The CV 500-I is designed to be used with the LN-7*,
LN-7 GMA*, LN-8*, LN-9*, LN-9 GMA*, LN-22,
LN-23P**, LN-25, or LN-742 semiautomatic wire feed-
ers, the NA-3*,NA-5* and NA-5R* automatics within
115 VOLT POWERꢀSWITCH
the capacity of the machine. The CV 500-I Diode
option is required to utilize the cold start and cold elec-
trode sensing features of the NA-3, NA-5 and NA-5R.
* The 14 pin receptacle of the European model does not provide 115 VAC for
these feeders..
The power input contactor operates from an auxiliary
115 volt transformer that is energized through the
POWER toggle switch on the machine control panel.
“ I ” is on and “0” is off.
** Use K350 Adapter Kit.
PILOT LIGHT
A white light on the machine control panel indicates
when the power source input contactor is closed. This
means the main power transformer and all auxiliary
and control transformers are energized.
DESIGN SUMMARY
Operational Features & Controls
ARCꢀCHARACTERISTICS
THERMAL PROTECTION LIGHT
Through the unique combination of the transformer,
three phase semiconverter rectifier, capacitor bank,
and output choke design, in conjunction with the solid
state control system, an outstanding constant voltage
welding performance is achieved with a fixed pinch
setting optimized for the most popular arc characteris-
tics.
An amber light on the machine control panel indicates
when either of the two protective thermostats have
opened. Output power will be removed but input
power will still be applied to the machine.
INPUT CONTACTOR
The power source is equipped with an input contactor.
OUTPUT VOLTAGE CONTROL
The OUTPUT voltage control, a small 2 watt poten-
tiometer, is calibrated from 1 to 10.
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
AUXILIARY POWER CONNECTIONS
SOLID STATE OUTPUT CONTROL
The power source is equipped to furnish nominally
115 volt AC and 42 volt AC auxiliary power for operat-
ing wire feeding equipment, etc. The auxiliary power
is available at the 14-pin MS-style connector recepta-
cle on the control panel and/or at a terminal strip
behind the hinged control panel on the front of the
power source. 115V AC is available at receptacle
pins A and J, (except on European model), and termi-
nals 31 and 32. 42V AC is available only at recepta-
cle pins I and K. The 115V AC and the 42V AC are
isolated circuits and each is protected by a 10 amp
circuit breaker.
The output of the welder is electronically controlled by
SCR’s instead of mechanical contactors, providing
extra long life for highly repetitive welding applica-
tions.
SOLID STATE CONTROL SYSTEM
The Control PC Board is located behind the control
panel which hinges down for easy access to the
board. The Snubber PCꢀBoard is mounted on the
back of the case front.
MACHINE COOLING
REMOTE CONTROL CONNECTIONS
The fan pulls air in through the louvered front of the
machine over the internal parts and exhausts out the
louvered rear of the machine. The fan motor is fully
enclosed, has sealed ball bearings, requires no lubri-
cation, and operates when the power switch is turned
on.
Remote control connections are available both at a
14-pin connector receptacle located on the control
panel, and on terminal strips with screw connections
located behind the hinged control panel on the front of
the power source.
WATERꢀCOOLERꢀCONNECTOR
CASE FEATURES
A Continental European receptacle (220V Schuko
type) is located on the rear panel for supplying
220VAC to a water cooler. A 2 amp circuit breaker
which is also located on the rear panel protects this
circuit.
The machine uses a 32” (813mm) long base. The low
profile case facilitates installation of the machine
under a workbench and stacking the machines three
high to conserve floor space.
The case front incorporates a recessed hinged control
panel where all the machine controls are mounted.
This recessed panel protects the controls and mini-
mizes the possibilities of accidental contact. This con-
trol panel can be easily opened to permit access to
the enclosed section which contains the terminal
strips, PC board, etc.The output lead terminals are
also recessed to avoid any object or person acciden-
tally coming in contact with an output terminal.
OUTPUT CONNECTIONS
The output terminals are recessed on the case front
and labeled “+” and “-”. The CV 500-I provides Twist-
Mate™ European connector receptacles.
K852 Twist-Mate European connector plugs are avail-
able for the cable size to be used. The Export model
includes two Twist-Mate plugs for 2/0 - 3/0 (70-
95mm2) cable and S18737 installation instructions.
The individual case sides are removable for easy
access for internal service or inspection. These are
removable even though the machines are stacked
three high.
INPUT CONNECTIONS
The three input lines are brought in through the rear
panel of the power source and attached to the input
contactor. Removal of the removable access panel
makes the contactor accessible for the input cable
connections.
The case rear, top section, is equipped with a remov-
able access panel. This provides easy access to the
input contactor, easy connection and reconnection of
input leads, and easy access for service or inspection.
Although the machine is designed for use in rain-sheltered
environemnts, the transformer and choke assembly
are dipped in a special corrosion resistant epoxy
paint.
INPUT LINE VOLTAGE COMPENSATION
The power source is equipped with input line voltage
compensation as standard. For a line voltage fluctua-
tion of ±10% the output will remain essentially con-
stant. This is accomplished through the feedback net-
work in the control circuit.
A permanent lifting hook is located at the top of the
machine and is positioned so that it acts as nearly as
possible through the center of gravity. This lift hook is
so positioned that it fits without interference under the
base of the second machine when stacking.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
PARALLELING
There are no provisions on the CV 500-I to permit par-
alleling.
DIODEꢀOPTION (Factory installed only)
The CV 500-I Diode option is required to utilize the
cold start and cold electrode sensing features of the
NA-3, NA-5 or NA-5R. When this option is not used
with an NA-3, NA-5 or NA-5R, see the CV 500-I /
NA-3, CV 500-I / NA-5 or CV 500-I / NA-5R connection
diagram for instructions on how to disable this circuit.
If the circuit is not disabled, the wire cannot be inched
down.
METERꢀOPTION
Factory installed Ammeter and Voltmeter
Machine & Circuit Protection
(Thermal Protection Light)
The power source is thermostatically protected with
proximity thermostats against overload or insufficient
cooling. One thermostat is located on the nose of the
center bottom primary coil and a second thermostat is
attached to the lead connecting the secondaries.
Both thermostats are connected in a series with the 2-
4 circuit. If the machine is overloaded, the primary
thermostat will open, the output will be zero, and the
thermal protection light will be on; the fan will continue
to run. The secondary thermostat will open either with
an excessive overload or insufficient cooling. The out-
put will be zero and the protection light will be on; the
fan will continue to run. When the thermostats reset
the protection light will be off.
The power source is also protected against overloads
on the SCR bridge assembly through an electronic
protection circuit. This circuit senses an overload on
the power source and limits the output to 550 amps by
phasing back the SCR’s.
Protection is provided to protect the circuitry from
accidental grounds. If the customer accidentally
“grounds” 75, 76, or 77 to the positive output lead, the
output will be reduced to a low value, thus preventing
any damage to the machine. If the ground occurs
between 75, 76, 77 and the negative output lead, one
of the PC board “self-restoring” fuses will blow, pre-
venting any machine damage. After the ground is
cleared, the fuses automatically reset within a few
seconds.
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SPECIFICATIONS
Model
Type
Frequency
CV 500-I
K1347
50/60ꢀHz
Output Rating
Amperes
DC
500 450
400
36
34
Volts NEMA EW1
IEC 974-1
Duty Cycle
40
39
38
36.5
50% 60% 100%
Output Range (Min.)
(Max.)
60A 12V
500A 42V
Max. O.C.V.
46
Input Ratings
220/440
220/380/440
230/460
Standard Voltages
Single Voltages (Available)
Rated Current
Input kVA
Power Factor
Efficiency
Yes
45A @ 400A 34V (380V/50 Hz)
29.6 @ 400A 34V (50 Hz)
.65 @ 400A 34V (50 Hz)
70% @ 400A 34V (50 Hz)
3.2A (380V 50 Hz)
1.0 KW (50 Hz)
Idle Current
Idle Power
Optional Features
Remote Control Adapter Cable
115V Starter Circuit
Suitable Undercarriages
Remote output Control
Yes
Standard
Yes
Yes
Stackable Case
Other Features
Net Weight
383 Lbs (174 kg)
M12244-7
L9269
Dimension Print
Wiring Diagram
Standards Compliance
Operating Temperature
IECꢀ974-1, S Rated (230/400V only)
NEMA EW1 (All others)
IP21 (All)
-40°C to +40°C
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATIONꢀLIMITATIONS
INSTALLATION
Safety Precautions
There are no provisions on the CV 500-I for parallel-
ing, and outdoor operations without rain sheltering is
not recommended.
WARNING
ELECTRIC SHOCK can kill.
• Do not touch electrically live parts or
electrode with skin or wet clothing.
• Insulate yourself from work and
ground.
STACKING
WARNING
FALLINGꢀEQUIPMENT can cause
injury.
• Do not lift this machine using lift bale if
it is equipped with a heavy accessory
such as trailer or gas cylinder.
• Always wear dry insulating gloves.
------------------------------------------------------------------------
FUMES AND GASES can be danger-
ous.
• Keep your head out of fumes.
• Use ventilation or exhaust to remove
fumes from breathing zone.
• Lift only with equipment of adequate lifting capacity.
• Be sure machine is stable when lifting.
• Do not stack more than three high.
• Do not stack the CV 500-I on top of any other
machine.
------------------------------------------------------------------------
WELDINGꢀSPARKSꢀcan cause fire or
explosion.
---------------------------------------------------------------------
• Keep flammable material away.
• Do not weld on closed containers.
The units may be stacked three high by observing the
following safety precautions.
------------------------------------------------------------------------
ARCꢀRAYS can burn eyes and skin.
• Wear eye, ear and body
1. Make sure the first or bottom unit is setting on a
level, well supported surface.
protection.
2. The units must be stacked with their fronts flush,
making sure the two holes in the base rails of the
unit being stacked on top are over the two holes
located on the top front corners of the unit it is
being stacked on. Fasten the units together with
5/16 bolts, nuts and lockwashers through these
holes.
------------------------------------------------------------
See additional warning information at
front of this operator’s manual.
-----------------------------------------------------------
3. Remove fastening bolts before lifting unit off stacks.
LOCATION
Input Power Connections
The machine should be located in a clean, dry place
where there is free circulation of clean air such that air
movement in through the front and out through the
back will not be restricted. Dirt and dust that can be
drawn into the machine should be kept to a minimum.
Failure to observe these precautions can result in
excessive operating temperatures and nuisance shut-
down of the machine.
By removing the rear access panel the three phase
input power is connected to the three line terminals on
the input contactor, and the earth grounding lead to
the grounding terminal on the input box floor marked
with the
symbol. Install the reconnect panel jumper
links for the proper input voltage per the diagram pasted
inside the access panel cover.
See Installation Data below:
INSTALLATIONꢀDATA
Recommended input wire and fuse sizes for maximum rated output.
In addition, follow latest National Electrical Code and Local Code.
Input Rating
Input Wire Size*
Amperes** (Type 75°C Copper
Minimum Grounding BUSSMANN SUPER-LAG
Wire Size
(Copper Conductors)
AWG
FUSE SIzE AND
CATALOG NUMBER***
FUSE SIzE CATALOG
NUMBER
on
Nameplate
Conductors in
Conduit)ꢀAWG
Voltage
220
Hertz
78
75
3 (27mm2)
4 (21mm2)
6 (13mm2)
8 (8.4mm2)
8 (8.4mm2)
8 (10mm2)
8 (10mm2)
10 (5.3mm2)
10 (5.3mm2)
10 (5.3mm2)
100
100
REN-100
REN-100
230
380
400
440
50/60
45
43
39
60
60
50
RES-60
RES-60
RES-50
*
Ambient temperature of 40°C (104°F).
** At rated output of 400A, 100% duty cycle.
*** Use only Bussmann Super-Lag fuses specified. Other fuses may not protect the welder and may cause over-
heating and possible fire damage.
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
CAUTION
REMOTE CONTROL ADAPTER CABLE (K864)
C
-
L
S
T
H
E
)
T
5
O
T
T
Failure to follow these instructions can cause immedi-
ate failure of components within the machine.
When powering welder from a generator be sure to
turn off the welder first, before generator is shut down
in order to prevent damage to welder.
CABLE RECEPTACLE (6 SOCKET)
STRAIGHT PLUG (14 PIN)
TO POWER SOURCE
TO: K857 REMOTE CONTROL
CABLE RECEPTACLE (14 SOCKET)
TO: LN-7 WIRE FEEDERS
Output Cable Connections
The output leads are connected to the output termi-
nals marked “+” and “-”. They are located at the lower
right and lower left corners of the front panel. The CV
500-I provides Twist-Mate European weld cable con-
nector receptacles.
A “V” cable 12” (.30m) long to connect a K857
Remote Control (6 pin connector) with a wire-feeder
(14-pin connector) and the machine (14-pin connec-
tor). If a remote control is used alone the wire-feeder
connection is then not used.
K852 Twist-Mate European connector plugs are avail-
able for the cable size to be used. The Export model
includes two Twist-Mate plugs for 2/0 - 3/0 (70-95mm2)
cable and S18737 installation instructions. This informa-
tion is also located at the rear of this manual.
WARNING
ELECTRIC SHOCK can kill.
• Turn the power switch of the
welding power source “OFF”
before installing plugs on cables or
when connecting or disconnecting plugs to
welding power source.
Output Cables
CABLE SIzES FOR COMBINED LENGTH OF
ELECTRODE AND WORK CABLE
MACHINE LOAD
------------------------------------------------------------
400A 500A
(100% DUTY (50% DUTY
CAPACITOR DISCHARGE CIRCUIT (K828-1)
CABLE LENGTHS
CYCLE)
CYCLE)
UP TO 50 ft
(15m)
3/0
85 mm2
2/0
67 mm2
Circuit that mounts inside the CV 500-I.
Recommended when:
50 to 100 ft
(15-30 m)
3/0
85 mm2
2/0
67 mm2
1) CV 500-I is used in conjunction with any LN-23P or
older LN-8 or LN-9 semiautomatic wire-feeder.
Eliminates possible arc flash re-start of weld when
trigger interlock is used. Not required with current
LN-8 (above Code 8700), or LN-9’s with serial
numbers above 115187 (manufactured after
12/83), or any LN-9 having an L6043-1 Power PC
Board.
100-150 ft
(30-46 m)
3/0
85 mm2
3/0
85 mm2
150-200 ft
(46-61 m)
3/0
85 mm2
3/0
85 mm2
200-250 ft
(67-76 m)
4/0
107 mm2
4/0
107 mm2
2) CV 500-I is used with an LN-22 equipped with an
older K279 Contactor-Voltage Control Option.
Eliminates electrode overrun when gun trigger is
released. Not required when later K279 (above
Code 8800) is used.
Installation of Field Installed Options
REMOTE OUTPUT CONTROL
(K857 WITH K864 ADAPTER OR K775 )
The K857 has a 6-pin MS-style connector. The K857
requires a K864 adapter cable which connects to the
14-pin connector on the machine.
The K775 consists of a control box with 28 ft (8.5m) of
four conductor cable. This connects to terminals 75, 76,
and 77 on the terminal strip and the case grounding
3) CV 500-I is used with any semiautomatic wire-
feeder and possible small spark, if electrode touch-
es work just after gun trigger is released, is objec-
tionable.
Install per M17060 instructions included with the
Kit.
screw so marked with the symbol
on the machine.
These terminals are located behind the control panel on
the front of the power source. This control will give the
same control as the output control on the machine.
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
UNDERCARRIAGES (K817P, K841)
CONNECTION OF CV 500-I TO LN-22 OR LN-25
For easy moving of the machine, optional undercar-
riages are available with polyolefin wheels (K817P) or
a platform undercarriage (K841) with mountings for
two gas cylinders at rear of welder.
a) Turn off all power.
b) Connect a jumper from “2 to 4” on terminal strip
TS2 or jumper pins “C to D” in 14-pin connector
plug ( a K484 14-pin jumper plug is available).
Install per instructions provided with undercarriage.
c) Connect the electrode cable to the output terminal
of polarity required by electrode. Connect the work
lead to the other terminal.
Installation of Equipment Required for
Recommended Processes
d) Place the OUTPUT CONTROL Switch at “LOCAL”
position unless a Remote Control is connected to
the CV 500-I.
WIRE FEEDER CONTROL CABLE CONNECTIONS
For control cable with 14-pin connector:
NOTE: The output terminals are energized at all
times.
Connect control cable to 14-pin connector on the front
panel of the machine. See the appropriate connection
diagram for the exact instructions for the wire feeder
being used. Refer to “115VAC and 42VAC Auxiliary
Power and Control Connections” section for connector
pin functions.
A cover (Lincoln Electric Part Number S17062-3) is
available for the unused 14-pin connector to protect it
against dirt and moisture.
For control cable with terminal strip connectors:
The control cable from the wire feeding equipment is
connected to the terminal strips behind the control
panel. A strain relief box connector is provided for
access into the terminal strip section. A chassis
ground screw is also provided below the terminal strip
marked with the symbol
for connecting the auto-
matic equipment grounding wire. See the appropriate
connection diagram for the exact instructions for the
wire feeder being used. Refer to “115VAC and 42VAC
Auxiliary Power and Control Connections” section for
access to terminal strips.
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
Safety Precautions
POWER SOURCE OPERATION
Duty Cycle and Time Period
WARNING
ELECTRICꢀSHOCK can kill.
• Have an electrician install and service
this equipment.
• Turn the input power off at the fuse
box before working on equipment.
The CV 500-I is rated at the following duty cycles:
Duty Cycle*
Amps
Volts
100%
60%
50%
400
450
500
36
38
40
• Do not touch electrically hot parts.
• This next section applies to CV 500-I’s without the
Capacitor Discharge Option:
---------------------------------------------------------------------
* Based upon a 10 minute time period. (i.e., for 60%
duty cycle, it is 6 minutes on and 4 minutes off).
When using a CV 500-I power source with wire feed-
ers, there will be a small spark if the electrode con-
tacts the work or ground within several seconds after
releasing the trigger.
Overloading the power source may result in opening
of an internal protective thermostat as indicated by the
amber thermal protection light turning on.
When used with some wire feeders with the electrical
trigger interlock in the ON position, the arc can restart
if the electrode touches the work or ground during
these several seconds.
STARTING THE MACHINE
The POWER toggle switch at the extreme right side of
the control panel in the “ I “ position energizes and
closes the three phase input contactor from a 115 volt
auxiliary transformer. This in turn energizes the main
power transformer.
The machine is de-energized when the POWER
switch is in the “0” position.
The white light next to the POWER switch indicates
when the input contactor is energized.
CONTROL SETTINGS & DESCRIPTIONS
OUTPUTꢀVOLTAGE CONTROL DIAL
The Output control dial at the right of the control panel
is a continuous control of the machine output voltage.
The control may be rotated between minimum and
maximum to adjust the machine output, even while
welding.
The machine is equipped with line voltage compensa-
tion as a standard feature. This will hold the output
constant except at maximum output of the machine,
through a fluctuation of ±10% input line voltage.
– 19 –
Download from Www.Somanuals.com. All Manuals Search And Download.
OUTPUT CONTROL “LOCAL-REMOTE” SWITCH
FRONT VIEW OF 14-PIN CONNECTOR
RECEPTACLE
The Output Control toggle switch on the control panel
labeled “Local-Remote” gives the operator the option
of controlling the output at the machine control panel
or at a remote station. For remote control, the toggle
switch is set in the “Remote” position and controlled at
the wire feed unit control, or by connecting a K775
control to terminals 75, 76, and 77 on the terminal
strip at the front of the machine, or by connecting a
K857 control with a K864 adapter to the 14-pin con-
nector on the front of the machine. For control at the
machine control panel (Output Voltage control dial),
the toggle switch is set in the “Local” position.
K=42
J=31
I=41
A=32
B=GND
L
N
C=2
D=4
E=77
H=21
G=75
F=76
M
PIN
LEADꢀNO.
FUNCTION
(Exception: When used with an LN-9, LN-9 GMA or
NA-5 wire feeder, the Output Control switch must be
in the “Remote” position or automatic shutdown of the
LN-9 or NA-5 may occur.)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
32
GND
2
115 VAC (Export Model Only)
Chassis Connection
Trigger Circuit
Trigger Circuit
Output Control
Output Control
Output Control
Work Connection
42 VAC
115 VAC (Export Model Only)
42 VAC
---
---
---
4
77
76
75
21
41
31
42
---
---
---
POLARITY SELECTION
Polarity selection is made by appropriately connecting
the electrode and work welding cables to either the
“+” terminal or to the “-” terminal. Select “Voltmeter”
switch for “+” or “-” electrode for the remote (#21)
work sensing lead.
VOLTMETER SWITCH
Select “+” for positive electrode or “-” for negative
electrode. This switch selects electrode polarity for the
remote (#21) work sensing lead of automatic or semi-
automatic equipment.
Terminal Strip Connections
Terminal strip TS2 located behind the hinged control
panel on the front of the power source supplies 115
VAC. A 10 amp circuit breaker protects this circuit.
This 115 VAC is also available in the 14-pin connector
(except on the European model).
THERMAL PROTECTION LIGHT
The amber thermal protection light will be lit if either of
the two protective thermostats have opened. The out-
put power will be disabled but input power will still be
applied to the welder.
Terminal strip TS1 also located behind the hinged
control panel allows for connecting of a K775 remote
control to terminals 75, 76, and 77.
115 VACꢀand 42 VACꢀAUXILIARY POWER AND
CONTROL CONNECTIONS
A chassis ground screw is provided below the terminal
strips marked with the symbol
for connecting the
automatic equipment grounding wire or remote control
grounding wire.
14-Pin Connector
The 14-pin connector receptacle (type MS-3102A-20-
27SX) supplies auxiliary power.
To gain access to the terminal strips simply remove
the two #10 sheet metal screws from the top of the
welder nameplate. Tilt panel forward so it rests in a
horizontal position. See Table above for lead number
functions.
42 VAC is available at receptacle pins I and K.
A 10 amp circuit breaker protects this circuit.
115 VAC is available at receptacle pins A and J
(except on the European model). A 10 amp circuit
breaker protects this circuit. Note that the 42 VAC and
115 VAC circuits are electrically isolated from each
other.
– 20 –
Download from Www.Somanuals.com. All Manuals Search And Download.
220 VAC AUXILIARY POWER FOR WATER COOLER
MAINTENANCE
A Continental European receptacle (220V Schuko
type) is located on the rear panel for supplying
220VAC to a water cooler. A 2 amp circuit breaker
which is also located on the rear panel protects this
circuit from excessive overloads or short circuits.
WARNING
ELECTRICꢀSHOCK can kill.
• Have an electrician install and service
this equipment.
• Turn the input power off at the fuse
box before working on equipment.
MACHINE AND CIRCUIT PROTECTION
• Do not touch electrically hot parts.
---------------------------------------------------------------------
The power source is thermostatically protected with
proximity thermostats against overload or insufficient
cooling. One thermostat is located on the nose of the
center bottom primary coil and a second thermostat is
attached to the lead connecting the secondaries. Both
thermostats are connected in series with 2-4 circuit. If
the machine is overloaded, the primary thermostat will
open, the output will be zero, the amber thermal pro-
tection light will be on and the fan will continue to run.
The secondary thermostat will open either with an
excessive overload or insufficient cooling. The output
will be zero, the amber protection light will be on and
the fan will continue to run. When the thermostats
reset the protection light will be off.
Routine Maintenance
1. The fan motor has sealed bearings which require
no service.
2. In extremely dusty locations, dirt may clog the air
channels causing the welder to run hot. Blow out
the machine at regular intervals.
3. In extremely dusty locations, dirt may accumulate
on the remote control terminal strip. Wipe or blow
this terminal strip off at regular intervals. This is
particularly important in damp locations.
The power source is also protected against overloads
on the SCR bridge assembly through the solid state
fault protection circuit. This circuit senses an overload
on the power source and limits the output to approxi-
mately 550 amps by phasing back the SCR’s.
Protection is provided to protect the circuitry from
accidental grounds. If leads 75, 76, or 77 are acciden-
tally “grounded” to the positive output lead, the output
will be reduced to a low value, thus preventing any
damage to the machine. If the ground occurs between
75, 76, 77 and the negative output lead, one of the PC
board electronic “self-restoring” fuses will blow, pre-
venting any machine damage. After the ground is
cleared, the fuses automatically reset within a few
seconds.
– 21 –
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
HOW TO USE TROUBLESHOOTING GUIDE
WARNING
Service and Repair should only be performed by Lincoln Electric Factory Trained Personnel.
Unauthorized repairs performed on this equipment may result in danger to the technician and
machine operator and will invalidate your factory warranty. For your safety and to avoid Electrical
Shock, please observe all safety notes and precautions detailed throughout this manual.
__________________________________________________________________________
This Troubleshooting Guide is provided to help you
locate and repair possible machine malfunctions.
Simply follow the three-step procedure listed below.
Step 3. RECOMMENDED COURSE OF ACTION
This column provides a course of action for the
Possible Cause, generally it states to contact your
local Lincoln Authorized Field Service Facility.
Step 1. LOCATE PROBLEMꢀ(SYMPTOM).
Look under the column labeled “PROBLEM (SYMP-
TOMS)”. This column describes possible symptoms
that the machine may exhibit. Find the listing that
best describes the symptom that the machine is
exhibiting.
If you do not understand or are unable to perform the
Recommended Course of Action safely, contact your
local Lincoln Authorized Field Service Facility.
Step 2. POSSIBLE CAUSE.
The second column labeled “POSSIBLE CAUSE” lists
the obvious external possibilities that may contribute
to the machine symptom.
CAUTION
If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your
Local Lincoln Authorized Field Service Facility for technical troubleshooting assistance before you proceed.
– 22 –
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTINGꢀGUIDE
Trouble
Cause
What To Do
1. Repair or replace.
2. Check input power.
1. Faulty input contactor (CR1).
2. Low line voltage.
Input contactor (CR1 chatters).
1. Replace if blown - look for reason
first.
1. Supply line fuse blown.
Machine input contactor does not
operate.
2. Check control transformer T2
and associated leads.
3. Check input voltage at contactor.
4. Check voltage against instruc-
tions.
2. Contactor power circuit dead.
3. Broken power lead.
4. Wrong input voltage.
5. Replace coil.
6. Replace switch.
5. Open input contactor coil.
6. POWER “I/O” switch (S1) not
closing.
1. Make sure trigger circuit is being
closed.
2. Repair connection.
1. Circuit between #2 (Cꢀ) and #4
(D) is not being closed.
2. Electrode or work lead loose or
broken.
Machine input contactor operates,
but no output when trying to weld.
3. Repair
3. Open main transformer (T1) pri-
mary or secondary circuit.
4. Defective Control PC Board.
4. Replace. See Procedure for
Replacing PC Boards.
5. Amber thermal protection light is
on: Check for overheating; make
sure fan is operating and there is
no obstruction to free air flow.
5. Primary or secondary ther-
mostats open.
1. Check 75, 76, or 77 for ground to
positive output circuit. Nearly
zero ohms to ground indicates a
grounded circuit. A value greater
than a few thousand ohms is nor-
mal. Self-restoring fuses on PC
Board automatically reset within
a few seconds after ground is
cleared.
1. Terminals 75, 76, or 77 grounded
to positive output.
Machine has minimum output and
no control.
1. Check 75, 76, or 77 for ground to
negative output circuit. Nearly
zero ohms to ground indicates a
grounded circuit. A value greater
than a few thousand ohms is nor-
mal. Self-restoring fuses on PC
Board automatically reset within
a few seconds after ground is
cleared.
1. Terminals 75, 76, or 77 grounded
to negative output.
Machine has high output and no
control.
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble
Cause
What To Do
Machine has low output and no con-
trol.
1. Output Control “Local-Remote”
switch (S2) in wrong position.
2. Output Control switch faulty.
1. Check position of switch.
2. Check switch and replace if
faulty.
3. Open in feedback circuitry.
4. Faulty Control PC Board.
3. Check wiring and control PC
Board wiring harness plugs.
4. Replace. See Procedure for
Replacing PC Boards.
5. Check and replace potentiometer
if faulty. Check wiring of Lead
#75.
5. Output control potentiometer cir-
cuit open (Lead 75).
Machine does not have maximum
output.
1. One input fuse blown.
1. Check and replace if blown after
checking for reason for blown
fuse.
2. One phase of main transformer
open.
3. Faulty Control PC Board.
2. Check for open and repair.
3. Replace. See Procedure for
Replacing PC Boards.
4. Check and replace if faulty.
4. Output control potentiometer
defective.
5. Output control potentiometer
Leads 210, 211, or 75 open.
5. Check and repair broken leads.
Machine will not shut off.
1. Input contactor contacts frozen.
2. Defective Power “I/O”
switch, (S1).
1. Check and replace if necessary.
2. Replace.
Variable or sluggish welding arc.
1. Poor work or electrode connec-
tion.
2. Welding leads too small.
1. Check and clean all connections.
2. Check table in instruction manual.
3. Welding current or voltage too
low.
4. Defective main SCR bridge.
3. Check procedures for recom-
mended settings.
4. Check and replace if defective.
Output control not functioning on the
machine.
1. Output Control “Local-Remote”
switch (S2) in wrong position.
1. Place switch in “Local”.
2. Faulty Output Control switch.
3. Faulty Output Control potentiometer.
2. Check and replace if found faulty.
3. Check and replace if found faulty.
4. Leads or connections open in
control circuit.
4. Check lead continuity and con-
nections for an open and repair if
necessary.
5. Faulty Control PC Board.
5. Replace. See Procedure for
Replacing PC Boards.
– 24 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble
Cause
What To Do
Output control not functioning on
“Remote” control.
1. Output Control switch in wrong
position.
1. Place switch in “Remote”.
2. Faulty Output Control switch.
3. Faulty remote control poten-
tiometer.
2. Check and replace if found faulty.
3. Check and replace if found faulty.
4. Leads or connections open in
control circuit.
4. Check all leads and connections,
internal or remote, for continuity;
repair if necessary.
5. Faulty Control PC Board.
5. Replace. See Procedure for
Replacing PC Boards.
Poor arc striking with semiautomatic
or automatic wire feeders.
1. Poor work connection.
2. Improper procedures.
1. Work connection must be ade-
quate for application.
2. Adjust procedures for improved
starting.
3. Defective Control PC Board.
3. Replace. See Procedure for
Replacing PC Boards.
Poor arc characteristics.
1. Defective Control PC Board.
1. Replace. See Procedure for
Replacing PC Boards.
2. Capacitor(s) in output circuit
failed. A failure is indicated if the
small vent plug on top of a
2. Replace entire bank of capaci-
tors. Do not replace individual
capacitors.
capacitor is raised or blown out.
WARNING: The liquid electrolyte
in these capacitors is toxic. Avoid
contact with any portion of your
body. Clean up vented electrolyte
using rubber gloves and a water
dampened cloth. Any electrolyte
which gets on skin, clean with
soap and water.
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Procedure for Replacing PC Boards
CHECKING SNUBBER PC BOARD
WARNING
ELECTRICꢀSHOCK can kill.
• Have an electrician install and service
this equipment.
In case of an SCR malfunction or failure, the Snubber
PC Board should be checked. Turn the machine off
and remove the sides of the machine. Board is mount-
ed on back of the case front.
• Turn the input power off at the fuse
box before working on equipment.
• Do not touch electrically hot parts.
---------------------------------------------------------------------
1. Visually inspect the Board for overheated compo-
nents or damaged components.
CHECKING OUTPUT CONTROL RHEOSTAT ON
MACHINE
When a PC board is suspected to be defective, the
following procedure must be followed:
Turn machine off (“0” position).
1. Visually inspect the PC board. If the board has
fuses, check to see if any are blown. Are any of
the components damaged? Is a conductor on the
back side of the board damaged? If electrical dam-
age is visible on the PC board, inspect the
machine wiring for grounds or shorts to avoid
damaging a new PC board. Install a new PC board
only after a visual inspection of the PC board and
machine wiring is satisfactory.
Remove the screws from the hinged control panel and
open the panel.
Turn the Output Control switch to “Remote”.
Disconnect the harness plug from the Control PC
Board.
With an ohmmeter on X1K, connect it to lead 210 and
75 on R4.
2. If the problem is remedied by a new PC board,
install the old PC board and see if the problem still
exists. If the problem does not return with the old
board:
Exercise caution to avoid damaging rheostat tabs.
Rotate the Output control rheostat. The resistance
reading should be from around zero to 10K ohms.
Check the resistance reading between 77 and 75 on
the terminal strip. The reading must be 10K ohms. No
reading will indicate an open rheostat and a low read-
ing will indicate a shorted or partially shorted rheostat;
in either case, replace.
a. Check the PC board harness plug and PC
board plug for contamination, corrosion or
oversize.
b. Check leads in the harness for loose connec-
tions.
CONNECTING THE REMOTE CONTROL TO THE
MACHINE
POWERꢀ“ I/O “ SWITCH CHECK
1. Turn off the machine input power (“0” position). S1
has 115 volts across it when the input power is
connected.
Extreme caution must be observed when installing or
extending the wiring of a remote control. Improper
connection of this unit can lead to loss of control
and/or poor welding. Only the green lead can and
should be grounded to the machine case. When
extending the standard remote control, make sure the
leads are the same and the splice is waterproof. Be
very careful not to ground the cable when in use and
don’t let the lugs touch against the case.
2. Isolate the switch to be tested by removing all con-
necting leads.
3. Check to make sure the switch is making open
and closed connections with a V.O.M. meter. Put
ohmmeter on X1 scale. The meter should read
zero resistance with switch “I” and infinite with
switch “0”.
OUTPUT VOLTAGE
The open circuit voltage of the machine should be
adjustable from 10 to 46 volts. If any other condition
exists, refer to the Troubleshooting Guide.
4. Put the ohmmeter on X1K scale and measure the
resistance between the terminal and the case of
the machine (touch a self-tapping screw). Reading
should be infinite.
FAULT PROTECTION OPERATION
5. If either step (3) or step (4) fails, replace the
switch.
The overload protection circuit, in the Control Board,
will limit the welding current (heat) to approximately
550 amps if a short or overload is applied to the
machine.
– 26 –
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL CHECK
resistance in both directions. An open diode will
have an infinite or high resistance in both direc-
tions and a good diode will have a low resistance
in Step b. and a much higher resistance in Step c.
Disconnect the remote output control and connect an
ohmmeter across 75 and 76 and rotate the rheostat in
the remote control. The resistance reading should go
from zero to 10K ohms. Repeat with ohmmeter across
77 and 76 with same results. Connect ohmmeter
across 75 and 77. The reading should be 10K ohms.
A lower reading will indicate a shorted or partially
shorted rheostat. A very high reading will indicate an
open rheostat. In either of the last two cases, replace
rheostat. Check cable for any physical damage.
3. Power Silicon Controlled Rectifier Test
The SCR must be mounted in the heat sink when
making this test.
a. Connect the ohmmeter (set to the X10 scale) leads
to the anode and cathode.
POWER RECTIFIER BRIDGE ASSEMBLY
CHECKING PROCEDURE
b. Reverse the leads of the ohmmeter from Step a.
c. A shorted SCR will indicate zero or an equally low
resistance in one or both directions.
WARNING
ELECTRICꢀSHOCK can kill.
• Have an electrician install and service
this equipment.
• Turn the input power off at the fuse
box before working on equipment.
d. Establish the polarity of the ohmmeter. Connect
the positive lead to the gate and the negative lead
to the cathode.
e. An open gate circuit will have an infinite or high
resistance. A good gate circuit will read a low
resistance, but not zero ohms. If gate circuit reads
zero ohms, check gate harness for shorts between
gate leads and 204 before replacing SCR.
• Do not touch electrically hot parts.
---------------------------------------------------------------------
1. Bridge and Device Isolation
Disconnect the following, shown in Diagram 1:
a. Unplug P3 (G1, G2, G3, and 204) from the Control
PC Board.
b. Unplug P5 from the Snubber PC Board.
c. Secondary leads X1, X2, and X3 from the anodes
of the SCR’s and cathodes of the diodes.
d. Disconnect positive bridge lead from shunt and
positive capacitor bank lead and from lug with dual
204 leads.
e. Perform following steps 2 and 3. If diodes and
SCR’s are not shorted, bridge test is completed. If
any device appears shorted, disconnect the cath-
ode lead of each diode (4 total) and repeat steps 2
and 3.
2. Power Diode Test
a. Establish the polarity of the ohmmeter leads and
set to X10 scale.
b. Connect the ohmmeter positive lead to anode and
negative lead to the cathode.
c. Reverse the leads of the ohmmeter from Step b.
d. A shorted diode will indicate zero or an equally low
– 27 –
Download from Www.Somanuals.com. All Manuals Search And Download.
6
C
t
9
2
f
o
t
t
A
e
s
v
)
e
l
C
d
K
B
T
T
W
C
L
I
L
A
N
C
S
TWIST-MATE WELDING CABLE PLUG INSTALLATION INSTRUCTIONS
TURN THE POWER SWITCH OF THE WELDING POWER
SOURCE "OFF" BEFORE INSTALLING PLUGS ON CABLES
OR WHEN CONNECTING OR DISCONNECTING PLUGS TO
WELDING POWER SOURCE.
CHECK THAT THE CONNECTOR BOOT IS MARKED FOR THE
APPROPRIATE CABLE SIZE PER TABLE BELOW; AND
SKIN CABLE JACKET TO LENGTH SPECIFIED:
1.
AMERICAN (EUROPEAN) RANGE
CABLE SIZE
CABLE SKIN LENGTH
BOOT MARKING
2
1
1
INCH (25.4mm)
INCH (25.4mm)
mm
)
35-50
50-70
70-95
#2-#1
(
35-50
2
mm
mm
)
1/0-2/0
2/0-3/0
(
50-70
(70-95
2
)
1.5 INCH (38.1mm)
If necessary, trim cable end of boot at groove(s) to match cable
diameter. Boot must fit tightly enough to seal around outside
2.
3.
diameter of cable. NOTE: Some boots are designed to accommodate
different cable diameters without trimming. These boots do not
have grooves at the cable end. Soap or other non petroleum
based lubricant will help to slide the boot over the cable.
Slide rubber boot onto cable end.
BOOT
WELDING CABLE
SEE
ABOVE
TRIM
Slide the copper tube into the brass plug.
4.
5.
SET SCREW
(70-95 size may
have set
screws)
Insert cable into copper tube.
2
BRASS PLUG
COPPER TUBE
Tighten set screw(s) to collapse copper tube. Screw(s)
must apply firm pressure against welding cable. The top of the
set screw(s) will be nearly flush or below the surface of the
brass plug after tightening.
6.
7.
Slide rubber boot over brass plug. The rubber boot must be
positioned to completely cover all electrical surfaces after
the plug is locked into the receptacle.
9-20-91J
S18737
RUBBER BOOT
MARKED WITH
"70-95"
.800
.740
N.A.
BRASS
.600
.553
.513
.503
.415
.385
TIN PLATED
COPPER TUBE
.200
.150
.207
.167
(2)SET SCREWS
NOTES:
N.A. DISPLACEMENT HOLE PERMISSIBLE.
N.B.
N.B. RELATIONSHIP BETWEEN SET SCREWS AND
RAISED TAB NOT IMPORTANT.
9-20-91J
M15479-1
– 28 –
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER RECTIFIER BRIDGEꢀ
DIAGRAM 1
PLUG TO SNUBBER BOARD
P5
220
_
+
220
223
204
221
222
X
X
X
3
1
2
D1
D2
ANODE D3
To (+) sideꢀ
of capacitorꢀ
bank
CATHODE
D4
ANODE
SCR1
SCR2
SCR3
GATE
CATHODE
SHUNT
_
+
204
P
U
O
N
B
B
D
2
2
X
2
P
2
A
D
X
s
D
D
D
O
4
of
ap
G
CAT
H
E
2
2
S
N
p
g
C
a
ꢀ
P3
G1
G2
G3
tr
T1
2
r
T
pl
204
204
G1
G2
G3
Gate leadsꢀ
plug to Controlꢀ
P.C. board
P3
To plugꢀ
P1
To T1 mainꢀ
transformer
– 29 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Enhanced Diagram
– 30 –
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Do not touch electrically live parts or
electrode with skin or wet clothing.
Insulate yourself from work and
ground.
•
•
Keep flammable materials away.
•
•
Wear eye, ear and body protection.
WARNING
Spanish
•
No toque las partes o los electrodos
bajo carga con la piel o ropa moja-
da.
Mantenga el material combustible
fuera del área de trabajo.
Protéjase los ojos, los oídos y el
cuerpo.
AVISO DE
PRECAUCION
French
•
•
Aislese del trabajo y de la tierra.
Ne laissez ni la peau ni des vête-
ments mouillés entrer en contact
avec des pièces sous tension.
Isolez-vous du travail et de la terre.
•
•
Gardez à l’écart de tout matériel
inflammable.
•
•
Protégez vos yeux, vos oreilles et
votre corps.
ATTENTION
•
•
German
Berühren Sie keine stromführenden
Teile oder Elektroden mit Ihrem
Körper oder feuchter Kleidung!
Isolieren Sie sich von den
Entfernen Sie brennbarres Material!
Tragen Sie Augen-, Ohren- und Kör-
perschutz!
WARNUNG
•
Elektroden und dem Erdboden!
Portuguese
•
•
Não toque partes elétricas e electro-
dos com a pele ou roupa molhada.
Isole-se da peça e terra.
•
Mantenha inflamáveis bem guarda-
dos.
•
Use proteção para a vista, ouvido e
corpo.
ATENÇÃO
Japanese
Chinese
Korean
Arabic
READ AND UNDERSTAND THE MANUFACTURER’S INSTRUCTION FOR THIS EQUIPMENT AND THE
CONSUMABLES TO BE USED AND FOLLOW YOUR EMPLOYER’S SAFETY PRACTICES.
SE RECOMIENDA LEER Y ENTENDER LAS INSTRUCCIONES DEL FABRICANTE PARA EL USO DE
ESTE EQUIPO Y LOS CONSUMIBLES QUE VA A UTILIZAR, SIGA LAS MEDIDAS DE SEGURIDAD DE SU
SUPERVISOR.
LISEZ ET COMPRENEZ LES INSTRUCTIONS DU FABRICANT EN CE QUI REGARDE CET EQUIPMENT
ET LES PRODUITS A ETRE EMPLOYES ET SUIVEZ LES PROCEDURES DE SECURITE DE VOTRE
EMPLOYEUR.
LESEN SIE UND BEFOLGEN SIE DIE BETRIEBSANLEITUNG DER ANLAGE UND DEN ELEKTRO-
DENEINSATZ DES HERSTELLERS. DIE UNFALLVERHÜTUNGSVORSCHRIFTEN DES ARBEITGEBERS
SIND EBENFALLS ZU BEACHTEN.
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Keep your head out of fumes.
Use ventilation or exhaust to
remove fumes from breathing zone.
•
•
Turn power off before servicing.
•
•
Do not operate with panel open or
guards off.
WARNING
Spanish
•
•
Los humos fuera de la zona de res-
piración.
Mantenga la cabeza fuera de los
humos. Utilice ventilación o
aspiración para gases.
Desconectar el cable de ali-
mentación de poder de la máquina
antes de iniciar cualquier servicio.
No operar con panel abierto o
guardas quitadas.
AVISO DE
PRECAUCION
French
•
•
Débranchez le courant avant l’entre-
tien.
•
•
N’opérez pas avec les panneaux
ouverts ou avec les dispositifs de
protection enlevés.
•
•
Gardez la tête à l’écart des fumées.
Utilisez un ventilateur ou un aspira-
teur pour ôter les fumées des zones
de travail.
ATTENTION
German
Strom vor Wartungsarbeiten
abschalten! (Netzstrom völlig öffnen;
Maschine anhalten!)
Anlage nie ohne Schutzgehäuse
oder Innenschutzverkleidung in
Betrieb setzen!
•
•
Vermeiden Sie das Einatmen von
Schweibrauch!
Sorgen Sie für gute Be- und
Entlüftung des Arbeitsplatzes!
WARNUNG
Portuguese
•
•
Não opere com as tampas removidas.
Desligue a corrente antes de fazer
serviço.
•
•
Mantenha-se afastado das partes
moventes.
Não opere com os paineis abertos
ou guardas removidas.
•
•
Mantenha seu rosto da fumaça.
Use ventilação e exhaustão para
remover fumo da zona respiratória.
ATENÇÃO
•
Não toque as partes elétricas nuas.
Japanese
Chinese
Korean
Arabic
LEIA E COMPREENDA AS INSTRUÇÕES DO FABRICANTE PARA ESTE EQUIPAMENTO E AS PARTES
DE USO, E SIGA AS PRÁTICAS DE SEGURANÇA DO EMPREGADOR.
Download from Www.Somanuals.com. All Manuals Search And Download.
• World's Leader in Welding and Cutting Products •
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: 216.481.8100 FAX: 216.486.1751 WEBꢀSITE: www.lincolnelectric.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|